Hi,
We have encountered the PHY issue on 6.1 LTS with SJA1105Q Switch
connected to DP84849I PHY. DP84849I PHY supports dual ethernet ports
so we configure the DT to connect two ports from the switch to PHY and
one port to CPU (FEC in i.MX6DL).
&ecspi2 {
cs-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi2>;
status = "okay";
switch@0 {
compatible = "nxp,sja1105q";
reg = <0>;
spi-max-frequency = <4000000>;
spi-rx-delay-us = <1>;
spi-tx-delay-us = <1>;
spi-cpha;
clocks = <&clk25m>;
pinctrl-0 = <&pinctrl_sja1105_rst>;
pinctrl-names = "default";
reset-gpios = <&gpio6 5 GPIO_ACTIVE_LOW>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
label = "ethphy0";
phy-handle = <ðphy0>;
phy-mode = "mii";
};
port@1 {
reg = <1>;
label = "ethphy1";
phy-handle = <ðphy1>;
phy-mode = "mii";
};
port@2 {
reg = <2>;
status = "disabled";
};
port@3 {
reg = <3>;
status = "disabled";
};
port@4 {
reg = <4>;
label = "cpu";
ethernet = <&fec>;
phy-mode = "mii";
rx-internal-delay-ps = <2000>;
tx-internal-delay-ps = <2000>;
fixed-link {
speed = <100>;
full-duplex;
};
};
};
};
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "mii";
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
ethphy0: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0>;
};
ethphy1: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
};
};
};
Since DP84849I shares the same register spec as DP83848, I have used
the DP83848 driver with the below PHY_ID change
diff --git a/drivers/net/phy/dp83848.c b/drivers/net/phy/dp83848.c
index c38d33fd3706..c2c82ce5bb41 100644
--- a/drivers/net/phy/dp83848.c
+++ b/drivers/net/phy/dp83848.c
@@ -8,6 +8,7 @@
#include <linux/module.h>
#include <linux/phy.h>
+#define TI_DP83849I_PHY_ID 0x20005ca2
#define TI_DP83848C_PHY_ID 0x20005ca0
#define TI_DP83620_PHY_ID 0x20005ce0
#define NS_DP83848C_PHY_ID 0x20005c90
@@ -173,6 +174,8 @@ MODULE_DEVICE_TABLE(mdio, dp83848_tbl);
}
static struct phy_driver dp83848_driver[] = {
+ DP83848_PHY_DRIVER(TI_DP83849I_PHY_ID, "TI DP83849I 10/100 Mbps PHY",
+ NULL),
DP83848_PHY_DRIVER(TI_DP83848C_PHY_ID, "TI DP83848C 10/100 Mbps PHY",
NULL),
DP83848_PHY_DRIVER(NS_DP83848C_PHY_ID, "NS DP83848C 10/100 Mbps PHY",
The Switch and dual-phy seem detecting as expected but when we try to
bring up the link the PHY0 says NOLINK as mentioned, below.
root@limx6solo:~# dmesg | grep sja
[ 23.765086] sja1105 spi1.0: spi_imx_setup: mode 1, 8 bpw, 4000000 hz
[ 23.765164] sja1105 spi1.0: setup mode 1, 8 bits/w, 4000000 Hz max --> 0
[ 23.766160] sja1105 spi1.0: Probed switch chip: SJA1105Q
[ 24.037103] sja1105 spi1.0: configuring for fixed/mii link mode
[ 24.119891] sja1105 spi1.0 ethphy0 (uninitialized): PHY
[2188000.ethernet-1:00] driver [TI DP83849I 10/100 Mbps PHY]
(irq=POLL)
[ 24.279129] sja1105 spi1.0 ethphy1 (uninitialized): PHY
[2188000.ethernet-1:01] driver [TI DP83849I 10/100 Mbps PHY]
(irq=POLL)
[ 26.406998] sja1105 spi1.0: Link is Up - 100Mbps/Full - flow control off
root@imx6solo:~# cat /usr/phy.sh
#!/bin/sh
echo ======= MDIO: PHY0 ========
mdio 2188000.ethernet-1 phy 0 raw 0x0
mdio 2188000.ethernet-1 phy 0 raw 0x1
mdio 2188000.ethernet-1 phy 0 raw 0x2
mdio 2188000.ethernet-1 phy 0 raw 0x3
mdio 2188000.ethernet-1 phy 0 raw 0x4
mdio 2188000.ethernet-1 phy 0 raw 0x5
mdio 2188000.ethernet-1 phy 0 raw 0x6
mdio 2188000.ethernet-1 phy 0 raw 0x7
mdio 2188000.ethernet-1 phy 0 raw 0x10
mdio 2188000.ethernet-1 phy 0 raw 0x19
echo ======= MDIO: PHY1 ========
mdio 2188000.ethernet-1 phy 1 raw 0x0
mdio 2188000.ethernet-1 phy 1 raw 0x1
mdio 2188000.ethernet-1 phy 1 raw 0x2
mdio 2188000.ethernet-1 phy 1 raw 0x3
mdio 2188000.ethernet-1 phy 1 raw 0x4
mdio 2188000.ethernet-1 phy 1 raw 0x5
mdio 2188000.ethernet-1 phy 1 raw 0x6
mdio 2188000.ethernet-1 phy 1 raw 0x7
mdio 2188000.ethernet-1 phy 1 raw 0x10
mdio 2188000.ethernet-1 phy 1 raw 0x19
ip link set dev eth0 down
ip link set dev ethphy0 down
ip link set dev ethphy1 down
ip link set dev ethphy0 address 00:11:22:33:44:55
ip link set dev ethphy1 address 00:11:22:33:44:66
ip addr add dev ethphy0 169.254.178.1/16
ip addr add dev ethphy1 169.253.178.2/16
ip link set dev eth0 up
ip link set dev ethphy0 up
ip link set dev ethphy1 up
echo ########## MDIO: PHY0 ###########
mdio 2188000.ethernet-1 phy 0 raw 0x0
mdio 2188000.ethernet-1 phy 0 raw 0x1
mdio 2188000.ethernet-1 phy 0 raw 0x2
mdio 2188000.ethernet-1 phy 0 raw 0x3
mdio 2188000.ethernet-1 phy 0 raw 0x4
mdio 2188000.ethernet-1 phy 0 raw 0x5
mdio 2188000.ethernet-1 phy 0 raw 0x6
mdio 2188000.ethernet-1 phy 0 raw 0x7
mdio 2188000.ethernet-1 phy 0 raw 0x10
mdio 2188000.ethernet-1 phy 0 raw 0x19
echo ########## MDIO: PHY1 ###########
mdio 2188000.ethernet-1 phy 1 raw 0x0
mdio 2188000.ethernet-1 phy 1 raw 0x1
mdio 2188000.ethernet-1 phy 1 raw 0x2
mdio 2188000.ethernet-1 phy 1 raw 0x3
mdio 2188000.ethernet-1 phy 1 raw 0x4
mdio 2188000.ethernet-1 phy 1 raw 0x5
mdio 2188000.ethernet-1 phy 1 raw 0x6
mdio 2188000.ethernet-1 phy 1 raw 0x7
mdio 2188000.ethernet-1 phy 1 raw 0x10
mdio 2188000.ethernet-1 phy 1 raw 0x19
root@ltts-imx6solo:~# bash /usr/phy.sh
======= MDIO: PHY0 ========
0x0: 0x3900
0x1: 0x7849
0x2: 0x2000
0x3: 0x5ca2
0x4: 0x01e1
0x5: 0x45e1
0x6: 0x0006
0x7: 0x2001
0x10: 0x0000
0x19: 0x8020
======= MDIO: PHY1 ========
0x0: 0x3100
0x1: 0x786d
0x2: 0x2000
0x3: 0x5ca2
0x4: 0x01e1
0x5: 0x45e1
0x6: 0x0007
0x7: 0x2801
0x10: 0x0015
0x19: 0x8021
ip link set dev eth0 down
ip link set dev ethphy0 down
ip link set dev ethphy1 down
ip link set dev ethphy0 address 00:11:22:33:44:55
ip link set dev ethphy1 address 00:11:22:33:44:66
ip link set dev eth0 up
ip link set dev ethphy0 up
ip link set dev ethphy1 up
[ 1254.929229] TI DP83849I 10/100 Mbps PHY 2188000.ethernet-1:00:
attached PHY driver (mii_bus:phy_addr=2188000.ethernet-1:00, irq=POLL)
[ 1254.993819] sja1105 spi1.0 ethphy0: configuring for phy/mii link mode
[ 1255.005027] ------------[ cut here ]------------
[ 1255.009962] WARNING: CPU: 0 PID: 374 at drivers/net/phy/phy.c:1157
phy_start+0x58/0xb4
[ 1255.018062] called from state NOLINK
[ 1255.021656] Modules linked in: mdio_netlink(O) bnep tag_sja1105
sja1105 pcs_xpcs brcmfmac brcmutil imx_sdma coda_vpu v4l2_jpeg
imx_vdoa evbug
[ 1255.034578] CPU: 0 PID: 374 Comm: ip Tainted: G O 6.1.58 #1
[ 1255.041560] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 1255.048103] unwind_backtrace from show_stack+0x10/0x14
[ 1255.053361] show_stack from dump_stack_lvl+0x58/0x70
[ 1255.058441] dump_stack_lvl from __warn+0x70/0x1a4
[ 1255.063258] __warn from warn_slowpath_fmt+0x1bc/0x270
[ 1255.068416] warn_slowpath_fmt from phy_start+0x58/0xb4
[ 1255.073662] phy_start from dsa_port_enable_rt+0x54/0x9c
[ 1255.079000] dsa_port_enable_rt from dsa_slave_open+0xb8/0x17c
[ 1255.084860] dsa_slave_open from __dev_open+0xec/0x1ac
[ 1255.090024] __dev_open from __dev_change_flags+0x18c/0x224
[ 1255.095613] __dev_change_flags from dev_change_flags+0x14/0x44
[ 1255.101549] dev_change_flags from do_setlink+0x254/0xe4c
[ 1255.106974] do_setlink from rtnl_newlink+0x598/0x80c
[ 1255.112048] rtnl_newlink from rtnetlink_rcv_msg+0x168/0x574
[ 1255.117722] rtnetlink_rcv_msg from netlink_rcv_skb+0xb8/0x11c
[ 1255.123572] netlink_rcv_skb from netlink_unicast+0x1a8/0x2dc
[ 1255.129343] netlink_unicast from netlink_sendmsg+0x1d8/0x450
[ 1255.135117] netlink_sendmsg from ____sys_sendmsg+0x188/0x258
[ 1255.140891] ____sys_sendmsg from ___sys_sendmsg+0x6c/0xa4
[ 1255.146397] ___sys_sendmsg from sys_sendmsg+0x50/0x98
[ 1255.151556] sys_sendmsg from ret_fast_syscall+0x0/0x1c
[ 1255.156801] Exception stack(0xf10c9fa8 to 0xf10c9ff0)
[ 1255.161867] 9fa0: 00000000 00000001 00000003
beef2730 00000000 00000000
[ 1255.170057] 9fc0: 00000000 00000001 b6f9e5a0 00000128 626adc51
00000000 004d1cc0 004d1cc0
[ 1255.178244] 9fe0: 00000128 beef26d0 b6e9f6d3 b6e11ae6
[ 1255.183469] irq event stamp: 3345
[ 1255.186852] hardirqs last enabled at (3355): [<c0195dbc>]
__up_console_sem+0x50/0x60
[ 1255.194715] hardirqs last disabled at (3362): [<c0195da8>]
__up_console_sem+0x3c/0x60
[ 1255.202628] softirqs last enabled at (3344): [<c01017d0>]
__do_softirq+0x2c0/0x57c
[ 1255.210365] softirqs last disabled at (3325): [<c012f204>]
__irq_exit_rcu+0x138/0x17c
[ 1255.218281] ---[ end trace 0000000000000000 ]---
[ 1255.293759] sja1105 spi1.0 ethphy1: configuring for phy/mii link mode
0x3100
0x7849
0x2000
0x5ca2
0x05e1
0x0000
0x0004
0x2001
0x0000
0x8020
0x3100
0x7849
0x2000
0x5ca2
0x0141
0x0000
0x0005
0x2801
0x0000
0x8021
root@ltts-imx6solo:~# [ 1257.045875] fec 2188000.ethernet eth0: Link
is Up - 100Mbps/Full - flow control rx/tx
[ 1257.054008] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1257.365971] sja1105 spi1.0 ethphy1: Link is Up - 100Mbps/Full -
flow control off
[ 1257.373455] IPv6: ADDRCONF(NETDEV_CHANGE): ethphy1: link becomes ready
root@ltts-imx6solo:~# ifconfig -a
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1504
inet6 fe80::7c4c:1aff:fe5e:cbf0 prefixlen 64 scopeid 0x20<link>
ether 7e:4c:1a:5e:cb:f0 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
ethphy0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 169.254.178.1 netmask 255.255.0.0 broadcast 0.0.0.0
ether 00:11:22:33:44:55 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
ethphy1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 169.253.178.2 netmask 255.255.0.0 broadcast 0.0.0.0
inet6 fe80::211:22ff:fe33:4466 prefixlen 64 scopeid 0x20<link>
ether 00:11:22:33:44:66 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 32 bytes 4211 (4.1 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 91 bytes 7801 (7.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 91 bytes 7801 (7.6 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
sit0: flags=128<NOARP> mtu 1480
unspec 00-00-00-00-31-00-00-4A-00-00-00-00-00-00-00-00
txqueuelen 1000 (UNSPEC)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether c0:ee:40:82:2f:fc txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
root@ltts-imx6solo:~# mdio 2188000.ethernet-1
DEV PHY-ID LINK
0x00 0x20005ca2 up
0x01 0x20005ca2 up
--
Jagan Teki,
Amarula Solutions India Pvt. Ltd.
Co-Founder & Embedded Linux Architect
405/E-Block, Sri Lakshmi Shubham Arcade, Chandanagar, Hyderabad - 500050, India
M. (+91) 910 009 0959
[`as] http://www.amarulasolutions.com
On Wed, Dec 20, 2023 at 12:49:30PM +0530, Jagan Teki wrote:
> [ 1255.021656] Modules linked in: mdio_netlink(O) bnep tag_sja1105 sja1105 pcs_xpcs brcmfmac brcmutil imx_sdma coda_vpu v4l2_jpeg imx_vdoa evbug
> [ 1255.034578] CPU: 0 PID: 374 Comm: ip Tainted: G O 6.1.58 #1
Can you please reproduce the issue with no out-of-tree modules used
(here mdio_netlink)?
On Fri, Dec 22, 2023 at 8:21 PM Vladimir Oltean <[email protected]> wrote:
>
> On Wed, Dec 20, 2023 at 12:49:30PM +0530, Jagan Teki wrote:
> > [ 1255.021656] Modules linked in: mdio_netlink(O) bnep tag_sja1105 sja1105 pcs_xpcs brcmfmac brcmutil imx_sdma coda_vpu v4l2_jpeg imx_vdoa evbug
> > [ 1255.034578] CPU: 0 PID: 374 Comm: ip Tainted: G O 6.1.58 #1
>
> Can you please reproduce the issue with no out-of-tree modules used
> (here mdio_netlink)?
root@imx6solo:~# ip link set dev eth0 down
root@imx6solo:~# ip link set dev ethphy0 down
root@imx6solo:~# ip link set dev ethphy1 down
root@imx6solo:~# ip link set dev ethphy0 address 00:11:22:33:44:55
root@imx6solo:~# ip link set dev ethphy1 address 00:11:22:33:44:66
root@imx6solo:~# ip addr add dev ethphy0 192.168.1.1/16
root@imx6solo:~# ip addr add dev ethphy1 192.168.1.5/16
root@imx6solo:~# ip link set dev eth0 up
[ 617.126753] dp83848_config_init: ret 0
[ 617.130831] TI DP83849I 10/100 Mbps PHY 2188000.ethernet-1:00:
attached PHY driver (mii_bus:phy_addr=2188000.ethernet-1:00, irq=POLL)
root@imx6solo:~# [ 619.207519] fec 2188000.ethernet eth0: Link is Up
- 100Mbps/Full - flow control rx/tx
[ 619.215698] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
root@imx6solo:~# ip link set dev ethphy0 up
[ 634.114608] sja1105 spi1.0 ethphy0: configuring for phy/mii link mode
[ 634.126617] ------------[ cut here ]------------
[ 634.131463] WARNING: CPU: 0 PID: 330 at drivers/net/phy/phy.c:1157
phy_start+0x58/0xb4
[ 634.139627] called from state RUNNING
[ 634.143310] Modules linked in: bnep tag_sja1105 sja1105 pcs_xpcs
brcmfmac brcmutil imx_sdma coda_vpu v4l2_jpeg imx_vdoa evbug
[ 634.154815] CPU: 0 PID: 330 Comm: ip Not tainted 6.1.58 #1
[ 634.160321] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 634.166866] unwind_backtrace from show_stack+0x10/0x14
[ 634.172125] show_stack from dump_stack_lvl+0x58/0x70
[ 634.177205] dump_stack_lvl from __warn+0x70/0x1a4
[ 634.182023] __warn from warn_slowpath_fmt+0x1bc/0x270
[ 634.187181] warn_slowpath_fmt from phy_start+0x58/0xb4
[ 634.192427] phy_start from dsa_port_enable_rt+0x54/0x9c
[ 634.197765] dsa_port_enable_rt from dsa_slave_open+0xb8/0x17c
[ 634.203624] dsa_slave_open from __dev_open+0xec/0x1ac
[ 634.208788] __dev_open from __dev_change_flags+0x18c/0x224
[ 634.214377] __dev_change_flags from dev_change_flags+0x14/0x44
[ 634.220313] dev_change_flags from do_setlink+0x254/0xe4c
[ 634.225737] do_setlink from rtnl_newlink+0x598/0x80c
[ 634.230811] rtnl_newlink from rtnetlink_rcv_msg+0x168/0x574
[ 634.236485] rtnetlink_rcv_msg from netlink_rcv_skb+0xb8/0x11c
[ 634.242337] netlink_rcv_skb from netlink_unicast+0x1a8/0x2dc
[ 634.248108] netlink_unicast from netlink_sendmsg+0x1d8/0x450
[ 634.253884] netlink_sendmsg from ____sys_sendmsg+0x188/0x258
[ 634.259656] ____sys_sendmsg from ___sys_sendmsg+0x6c/0xa4
[ 634.265164] ___sys_sendmsg from sys_sendmsg+0x50/0x98
[ 634.270324] sys_sendmsg from ret_fast_syscall+0x0/0x1c
[ 634.275569] Exception stack(0xf1071fa8 to 0xf1071ff0)
[ 634.280637] 1fa0: 00000000 00000001 00000003
bef4d710 00000000 00000000
[ 634.288828] 1fc0: 00000000 00000001 b6f415a0 00000128 626ad475
00000000 00531cc0 00531cc0
[ 634.297016] 1fe0: 00000128 bef4d6b0 b6e3f6d3 b6db1ae6
[ 634.302150] irq event stamp: 3327
[ 634.305485] hardirqs last enabled at (3335): [<c0195dbc>]
__up_console_sem+0x50/0x60
[ 634.313404] hardirqs last disabled at (3344): [<c0195da8>]
__up_console_sem+0x3c/0x60
[ 634.321318] softirqs last enabled at (3230): [<c01017d0>]
__do_softirq+0x2c0/0x57c
[ 634.329055] softirqs last disabled at (3187): [<c012f204>]
__irq_exit_rcu+0x138/0x17c
[ 634.336971] ---[ end trace 0000000000000000 ]---
root@imx6solo:~# ip link set dev ethphy1 up
[ 644.613564] sja1105 spi1.0 ethphy1: configuring for phy/mii link mode
root@imx6solo:~# [ 646.727549] sja1105 spi1.0 ethphy1: Link is Up -
100Mbps/Full - flow control off
[ 646.735033] IPv6: ADDRCONF(NETDEV_CHANGE): ethphy1: link becomes ready
Thanks,
Jagan.
On Tue, Dec 26, 2023 at 01:11:08PM +0530, Jagan Teki wrote:
> &fec {
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_enet>;
> phy-mode = "mii";
> status = "okay";
tl;dr: I think what is missing is:
fixed-link {
speed = <100>;
full-duplex;
};
>
> mdio {
> #address-cells = <1>;
> #size-cells = <0>;
>
> ethphy0: ethernet-phy@0 {
> compatible = "ethernet-phy-ieee802.3-c22";
> reg = <0>;
> };
>
> ethphy1: ethernet-phy@1 {
> compatible = "ethernet-phy-ieee802.3-c22";
> reg = <1>;
> };
> };
> };
>
> root@imx6solo:~# ip link set dev eth0 down
> root@imx6solo:~# ip link set dev ethphy0 down
> root@imx6solo:~# ip link set dev ethphy1 down
> root@imx6solo:~# ip link set dev ethphy0 address 00:11:22:33:44:55
> root@imx6solo:~# ip link set dev ethphy1 address 00:11:22:33:44:66
> root@imx6solo:~# ip addr add dev ethphy0 192.168.1.1/16
> root@imx6solo:~# ip addr add dev ethphy1 192.168.1.5/16
> root@imx6solo:~# ip link set dev eth0 up
> [ 617.126753] dp83848_config_init: ret 0
> [ 617.130831] TI DP83849I 10/100 Mbps PHY 2188000.ethernet-1:00: attached PHY driver (mii_bus:phy_addr=2188000.ethernet-1:00, irq=POLL)
> root@imx6solo:~# [ 619.207519] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
> [ 619.215698] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0 is the FEC port, right?
> root@imx6solo:~# ip link set dev ethphy0 up
> [ 634.114608] sja1105 spi1.0 ethphy0: configuring for phy/mii link mode
> [ 634.126617] ------------[ cut here ]------------
> [ 634.131463] WARNING: CPU: 0 PID: 330 at drivers/net/phy/phy.c:1157 phy_start+0x58/0xb4
> [ 634.139627] called from state RUNNING
> [ 634.143310] Modules linked in: bnep tag_sja1105 sja1105 pcs_xpcs brcmfmac brcmutil imx_sdma coda_vpu v4l2_jpeg imx_vdoa evbug
> [ 634.154815] CPU: 0 PID: 330 Comm: ip Not tainted 6.1.58 #1
> [ 634.160321] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
> [ 634.166866] unwind_backtrace from show_stack+0x10/0x14
> [ 634.172125] show_stack from dump_stack_lvl+0x58/0x70
> [ 634.177205] dump_stack_lvl from __warn+0x70/0x1a4
> [ 634.182023] __warn from warn_slowpath_fmt+0x1bc/0x270
> [ 634.187181] warn_slowpath_fmt from phy_start+0x58/0xb4
> [ 634.192427] phy_start from dsa_port_enable_rt+0x54/0x9c
> [ 634.197765] dsa_port_enable_rt from dsa_slave_open+0xb8/0x17c
> [ 634.203624] dsa_slave_open from __dev_open+0xec/0x1ac
> [ 634.208788] __dev_open from __dev_change_flags+0x18c/0x224
> [ 634.214377] __dev_change_flags from dev_change_flags+0x14/0x44
> [ 634.220313] dev_change_flags from do_setlink+0x254/0xe4c
> [ 634.225737] do_setlink from rtnl_newlink+0x598/0x80c
> [ 634.230811] rtnl_newlink from rtnetlink_rcv_msg+0x168/0x574
> [ 634.236485] rtnetlink_rcv_msg from netlink_rcv_skb+0xb8/0x11c
> [ 634.242337] netlink_rcv_skb from netlink_unicast+0x1a8/0x2dc
> [ 634.248108] netlink_unicast from netlink_sendmsg+0x1d8/0x450
> [ 634.253884] netlink_sendmsg from ____sys_sendmsg+0x188/0x258
> [ 634.259656] ____sys_sendmsg from ___sys_sendmsg+0x6c/0xa4
> [ 634.265164] ___sys_sendmsg from sys_sendmsg+0x50/0x98
> [ 634.270324] sys_sendmsg from ret_fast_syscall+0x0/0x1c
> [ 634.275569] Exception stack(0xf1071fa8 to 0xf1071ff0)
> [ 634.280637] 1fa0: 00000000 00000001 00000003 bef4d710 00000000 00000000
> [ 634.288828] 1fc0: 00000000 00000001 b6f415a0 00000128 626ad475 00000000 00531cc0 00531cc0
> [ 634.297016] 1fe0: 00000128 bef4d6b0 b6e3f6d3 b6db1ae6
> [ 634.302150] irq event stamp: 3327
> [ 634.305485] hardirqs last enabled at (3335): [<c0195dbc>] __up_console_sem+0x50/0x60
> [ 634.313404] hardirqs last disabled at (3344): [<c0195da8>] __up_console_sem+0x3c/0x60
> [ 634.321318] softirqs last enabled at (3230): [<c01017d0>] __do_softirq+0x2c0/0x57c
> [ 634.329055] softirqs last disabled at (3187): [<c012f204>] __irq_exit_rcu+0x138/0x17c
> [ 634.336971] ---[ end trace 0000000000000000 ]---
> root@imx6solo:~# ip link set dev ethphy1 up
> [ 644.613564] sja1105 spi1.0 ethphy1: configuring for phy/mii link mode
> root@imx6solo:~# [ 646.727549] sja1105 spi1.0 ethphy1: Link is Up -
> 100Mbps/Full - flow control off
> [ 646.735033] IPv6: ADDRCONF(NETDEV_CHANGE): ethphy1: link becomes ready
Ok. The WARN_ON() is saying that the DSA user port's phy_start() found
the attached PHY already in the RUNNING state. As if there was already
someone else driving it.
That "someone else" seems to be the FEC driver from the log above, which
for some reason has connected to the DP83849I by itself, and phylink/phylib
hasn't denied the second attempt to connect to the same PHY for some
reason.
If you look at fec_enet_mii_probe(), I see it has 2 code paths, one for
when fep->phy_node (defined as the "phy-handle" reference) is non-NULL,
and one for when it is NULL. What you're missing is a fixed-link
specifier in the device tree for FEC, otherwise it tries to call
phy_connect() to some random MDIO address on the bus and that breaks
things in some way which I don't understand.
The code which should have prevented this from happening is in
phy_attach_direct():
if (phydev->attached_dev) {
dev_err(&dev->dev, "PHY already attached\n");
err = -EBUSY;
goto error;
}
> Ok. The WARN_ON() is saying that the DSA user port's phy_start() found
> the attached PHY already in the RUNNING state. As if there was already
> someone else driving it.
>
> That "someone else" seems to be the FEC driver from the log above, which
> for some reason has connected to the DP83849I by itself, and phylink/phylib
> hasn't denied the second attempt to connect to the same PHY for some
> reason.
>
> If you look at fec_enet_mii_probe(), I see it has 2 code paths, one for
> when fep->phy_node (defined as the "phy-handle" reference) is non-NULL,
> and one for when it is NULL. What you're missing is a fixed-link
> specifier in the device tree for FEC, otherwise it tries to call
> phy_connect() to some random MDIO address on the bus and that breaks
> things in some way which I don't understand.
At has an open coded phy_find_first(), or something similar. The FEC
is a bit of a mess in this respect, but it is hard to fix because of
backwards compatibility.
> The code which should have prevented this from happening is in
> phy_attach_direct():
>
> if (phydev->attached_dev) {
> dev_err(&dev->dev, "PHY already attached\n");
> err = -EBUSY;
> goto error;
> }
Yes, that is odd.
Andrew
> The code which should have prevented this from happening is in
> phy_attach_direct():
>
> if (phydev->attached_dev) {
> dev_err(&dev->dev, "PHY already attached\n");
> err = -EBUSY;
> goto error;
> }
The problem might be dsa_shared_port_phylink_register():
err = phylink_of_phy_connect(dp->pl, port_dn, 0);
if (err && err != -ENODEV) {
pr_err("could not attach to PHY: %d\n", err);
goto err_phy_connect;
}
return 0;
Since it is not -ENODEV, it just keep going.
Andrew
On Tue, Dec 26, 2023 at 06:00:17PM +0100, Andrew Lunn wrote:
> > The code which should have prevented this from happening is in
> > phy_attach_direct():
> >
> > if (phydev->attached_dev) {
> > dev_err(&dev->dev, "PHY already attached\n");
> > err = -EBUSY;
> > goto error;
> > }
>
> The problem might be dsa_shared_port_phylink_register():
>
> err = phylink_of_phy_connect(dp->pl, port_dn, 0);
> if (err && err != -ENODEV) {
> pr_err("could not attach to PHY: %d\n", err);
> goto err_phy_connect;
> }
>
> return 0;
>
> Since it is not -ENODEV, it just keep going.
>
> Andrew
"Shared" ports are DSA and CPU ports, the report is on a user port.
There, if phylink_of_phy_connect() fails, we try dsa_user_phy_connect(),
but only if the driver provides a ds->user_mii_bus, which sja1105 does not.
So the failure should be nice and clean. It might be worth posting a
full boot log though, since this is really strange.
On Tue, Dec 26, 2023 at 9:00 PM Vladimir Oltean <[email protected]> wrote:
>
> On Tue, Dec 26, 2023 at 01:11:08PM +0530, Jagan Teki wrote:
> > &fec {
> > pinctrl-names = "default";
> > pinctrl-0 = <&pinctrl_enet>;
> > phy-mode = "mii";
> > status = "okay";
>
> tl;dr: I think what is missing is:
>
> fixed-link {
> speed = <100>;
> full-duplex;
> };
Okay. I added this and now the warning seems gone. Please check the below log.
>
> >
> > mdio {
> > #address-cells = <1>;
> > #size-cells = <0>;
> >
> > ethphy0: ethernet-phy@0 {
> > compatible = "ethernet-phy-ieee802.3-c22";
> > reg = <0>;
> > };
> >
> > ethphy1: ethernet-phy@1 {
> > compatible = "ethernet-phy-ieee802.3-c22";
> > reg = <1>;
> > };
> > };
> > };
> >
> > root@imx6solo:~# ip link set dev eth0 down
> > root@imx6solo:~# ip link set dev ethphy0 down
> > root@imx6solo:~# ip link set dev ethphy1 down
> > root@imx6solo:~# ip link set dev ethphy0 address 00:11:22:33:44:55
> > root@imx6solo:~# ip link set dev ethphy1 address 00:11:22:33:44:66
> > root@imx6solo:~# ip addr add dev ethphy0 192.168.1.1/16
> > root@imx6solo:~# ip addr add dev ethphy1 192.168.1.5/16
> > root@imx6solo:~# ip link set dev eth0 up
> > [ 617.126753] dp83848_config_init: ret 0
> > [ 617.130831] TI DP83849I 10/100 Mbps PHY 2188000.ethernet-1:00: attached PHY driver (mii_bus:phy_addr=2188000.ethernet-1:00, irq=POLL)
> > root@imx6solo:~# [ 619.207519] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
> > [ 619.215698] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
>
> eth0 is the FEC port, right?
Yes.
With fec0 fixed-link and 3 different switch port configurations, the
result of the link seems to be up but the ping not working and even
the packets are not transmitted via eth0.
DT Combinations:
- Port0 is ethphy0, Port1 is ethphy1, Port2 is disabled, Port3 is
disabled, Port4 is FEC
- Port0 is disabled, Port1 is ethphy0, Port2 is ethphy1, Port3 is
disabled, Port4 is FEC
- Port0 is disabled, Port1 is disabled, Port2 is ethphy0, Port3 is
ethphy1, Port4 as FEC
DT: (with Port0 is ethphy0, Port1 is ethphy1, Port2 is disabled, Port3
is disabled, Port4 is FEC)
&ecspi2 {
cs-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi2>;
status = "okay";
switch@0 {
compatible = "nxp,sja1105q";
reg = <0>;
spi-max-frequency = <4000000>;
spi-rx-delay-us = <1>;
spi-tx-delay-us = <1>;
spi-cpha;
clocks = <&clk25m>;
pinctrl-0 = <&pinctrl_sja1105_rst>;
pinctrl-names = "default";
reset-gpios = <&gpio6 5 GPIO_ACTIVE_LOW>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
label = "ethphy0";
phy-handle = <ðphy0>;
phy-mode = "mii";
};
port@1 {
reg = <1>;
label = "ethphy1";
phy-handle = <ðphy1>;
phy-mode = "mii";
};
port@2 {
reg = <2>;
status = "disabled";
};
port@3 {
reg = <3>;
status = "disabled";
};
port@4 {
reg = <4>;
label = "cpu";
ethernet = <&fec>;
phy-mode = "mii";
rx-internal-delay-ps = <2000>;
tx-internal-delay-ps = <2000>;
fixed-link {
speed = <100>;
full-duplex;
};
};
};
};
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "mii";
status = "okay";
fixed-link {
speed = <100>;
full-duplex;
};
mdio {
#address-cells = <1>;
#size-cells = <0>;
ethphy0: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0>;
};
ethphy1: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
};
};
};
Full dmesg:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 6.1.58 (oe-user@oe-host)
(arm-fslc-linux-gnueabi-gcc (GCC) 11.4.0, GNU ld (GNU Binutils)
2.38.20220708) #1 SMP Sun Oct 15 16:32:41 UTC 2023
[ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] OF: fdt: Machine model: LTTS i.MX6DL/SOLO Processor
Board (P0-PHY0, P1-PHY1)
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 64 MiB at 0x4c000000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000010000000-0x000000003fffffff]
[ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff]
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] percpu: Embedded 17 pages/cpu s38452 r8192 d22988 u69632
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608
[ 0.000000] Kernel command line: console=ttymxc1,115200
root=/dev/mmcblk0p2 rootwait rw
mtdparts=gpmi-nand:2m(spl),2m(uboot),1m(env),16m(kernel),1m(dtb),-(rootfs)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7,
524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144
bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 942324K/1048576K available (15360K kernel code,
2198K rwdata, 5632K rodata, 1024K init, 6674K bss, 40716K reserved,
65536K cma-reserved, 196608K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] trace event string verifier disabled
[ 0.000000] Running RCU self tests
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU lockdep checking is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay
is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] L2C-310 erratum 769419 enabled
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 cache controller enabled, 16 ways, 512 kB
[ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76450001
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] Switching to timer-based delay loop, resolution 333ns
[ 0.000001] sched_clock: 32 bits at 3000kHz, resolution 333ns,
wraps every 715827882841ns
[ 0.000026] clocksource: mxc_timer1: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 637086815595 ns
[ 0.002024] Console: colour dummy device 80x30
[ 0.002103] Lock dependency validator: Copyright (c) 2006 Red Hat,
Inc., Ingo Molnar
[ 0.002115] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.002127] ... MAX_LOCK_DEPTH: 48
[ 0.002140] ... MAX_LOCKDEP_KEYS: 8192
[ 0.002151] ... CLASSHASH_SIZE: 4096
[ 0.002163] ... MAX_LOCKDEP_ENTRIES: 32768
[ 0.002174] ... MAX_LOCKDEP_CHAINS: 65536
[ 0.002186] ... CHAINHASH_SIZE: 32768
[ 0.002197] memory used by lock dependency info: 4061 kB
[ 0.002209] memory used for stack traces: 2112 kB
[ 0.002220] per task-struct memory footprint: 1536 bytes
[ 0.002337] Calibrating delay loop (skipped), value calculated
using timer frequency.. 6.00 BogoMIPS (lpj=30000)
[ 0.002370] CPU: Testing write buffer coherency: ok
[ 0.002550] CPU0: Spectre v2: using BPIALL workaround
[ 0.002570] pid_max: default: 32768 minimum: 301
[ 0.003241] Mount-cache hash table entries: 2048 (order: 1, 8192
bytes, linear)
[ 0.003279] Mountpoint-cache hash table entries: 2048 (order: 1,
8192 bytes, linear)
[ 0.008782] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.012642] cblist_init_generic: Setting adjustable number of
callback queues.
[ 0.012663] cblist_init_generic: Setting shift to 1 and lim to 1.
[ 0.013078] Running RCU-tasks wait API self tests
[ 0.013428] Setting up static identity map for 0x10100000 - 0x10100078
[ 0.014115] Callback from call_rcu_tasks_trace() invoked.
[ 0.014401] rcu: Hierarchical SRCU implementation.
[ 0.014416] rcu: Max phase no-delay instances is 1000.
[ 0.017147] smp: Bringing up secondary CPUs ...
[ 0.020861] smp: Brought up 1 node, 1 CPU
[ 0.020887] SMP: Total of 1 processors activated (6.00 BogoMIPS).
[ 0.020906] CPU: All CPU(s) started in SVC mode.
[ 0.023936] devtmpfs: initialized
[ 0.064038] VFP support v0.3: implementor 41 architecture 3 part 30
variant 9 rev 4
[ 0.066614] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.066685] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.069638] pinctrl core: initialized pinctrl subsystem
[ 0.076431] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.103057] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.108831] thermal_sys: Registered thermal governor 'step_wise'
[ 0.109233] cpuidle: using governor menu
[ 0.109642] CPU identified as i.MX6DL, silicon rev 1.4
[ 0.129331] platform soc: Fixed dependency cycle(s) with
/soc/bus@2000000/gpc@20dc000
[ 0.196131] platform 2400000.ipu: Fixed dependency cycle(s) with
/ldb/lvds-channel@0/port@1/endpoint
[ 0.196257] platform 2400000.ipu: Fixed dependency cycle(s) with
/ldb/lvds-channel@0/port@0/endpoint
[ 0.196358] platform 2400000.ipu: Fixed dependency cycle(s) with
/soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi1_mux/port@5/endpoint
[ 0.196495] platform 2400000.ipu: Fixed dependency cycle(s) with
/soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi0_mux/port@5/endpoint
[ 0.201135] platform panel: Fixed dependency cycle(s) with
/ldb/lvds-channel@0/port@4/endpoint
[ 0.208560] No ATAGs?
[ 0.208881] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1
watchpoint registers.
[ 0.208926] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.214921] imx6dl-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver
[ 0.272738] kprobes: kprobe jump-optimization is enabled. All
kprobes are optimized if possible.
[ 1.498973] SCSI subsystem initialized
[ 1.501106] usbcore: registered new interface driver usbfs
[ 1.501396] usbcore: registered new interface driver hub
[ 1.501565] usbcore: registered new device driver usb
[ 1.502033] usb_phy_generic usbphynop1: supply vcc not found, using
dummy regulator
[ 1.502911] usb_phy_generic usbphynop1: dummy supplies not allowed
for exclusive requests
[ 1.503404] usb_phy_generic usbphynop2: supply vcc not found, using
dummy regulator
[ 1.504037] usb_phy_generic usbphynop2: dummy supplies not allowed
for exclusive requests
[ 1.510235] i2c i2c-0: IMX I2C adapter registered
[ 1.514947] i2c i2c-1: IMX I2C adapter registered
[ 1.518067] i2c i2c-2: IMX I2C adapter registered
[ 1.518853] mc: Linux media interface: v0.10
[ 1.519141] videodev: Linux video capture interface: v2.00
[ 1.522785] pps_core: LinuxPPS API ver. 1 registered
[ 1.522807] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
Rodolfo Giometti <[email protected]>
[ 1.522874] PTP clock support registered
[ 1.525697] Advanced Linux Sound Architecture Driver Initialized.
[ 1.529830] Bluetooth: Core ver 2.22
[ 1.529992] NET: Registered PF_BLUETOOTH protocol family
[ 1.530010] Bluetooth: HCI device and connection manager initialized
[ 1.530145] Bluetooth: HCI socket layer initialized
[ 1.530180] Bluetooth: L2CAP socket layer initialized
[ 1.530347] Bluetooth: SCO socket layer initialized
[ 1.533222] vgaarb: loaded
[ 1.535344] clocksource: Switched to clocksource mxc_timer1
[ 1.538364] VFS: Disk quotas dquot_6.6.0
[ 1.538543] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.579519] NET: Registered PF_INET protocol family
[ 1.580549] IP idents hash table entries: 16384 (order: 5, 131072
bytes, linear)
[ 1.584148] tcp_listen_portaddr_hash hash table entries: 512
(order: 2, 20480 bytes, linear)
[ 1.584256] Table-perturb hash table entries: 65536 (order: 6,
262144 bytes, linear)
[ 1.584303] TCP established hash table entries: 8192 (order: 3,
32768 bytes, linear)
[ 1.584658] TCP bind hash table entries: 8192 (order: 7, 655360
bytes, linear)
[ 1.586988] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.587712] UDP hash table entries: 512 (order: 3, 49152 bytes, linear)
[ 1.587929] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear)
[ 1.588553] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.591483] RPC: Registered named UNIX socket transport module.
[ 1.591536] RPC: Registered udp transport module.
[ 1.591553] RPC: Registered tcp transport module.
[ 1.591567] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.593486] PCI: CLS 0 bytes, default 64
[ 1.595609] armv7-pmu pmu: hw perfevents: no interrupt-affinity
property, guessing.
[ 1.598721] hw perfevents: enabled with armv7_cortex_a9 PMU driver,
7 counters available
[ 1.606329] Initialise system trusted keyrings
[ 1.607301] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[ 1.635184] NFS: Registering the id_resolver key type
[ 1.635456] Key type id_resolver registered
[ 1.635507] Key type id_legacy registered
[ 1.635885] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.635995] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver
Registering...
[ 1.636188] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 1.637781] fuse: init (API version 7.37)
[ 1.730733] Key type asymmetric registered
[ 1.730857] Asymmetric key parser 'x509' registered
[ 1.731593] bounce: pool size: 64 pages
[ 1.732072] io scheduler mq-deadline registered
[ 1.732097] io scheduler kyber registered
[ 1.749796] pwm-backlight backlight-lvds: supply power not found,
using dummy regulator
[ 1.794041] mxs-dma 110000.dma-apbh: initialized
[ 1.830861] pfuze100-regulator 1-0008: Full layer: 2, Metal layer: 1
[ 1.831964] pfuze100-regulator 1-0008: FAB: 0, FIN: 0
[ 1.831988] pfuze100-regulator 1-0008: pfuze100 found.
[ 1.911047] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 268,
base_baud = 5000000) is a IMX
[ 3.289603] printk: console [ttymxc1] enabled
[ 3.298390] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 269,
base_baud = 5000000) is a IMX
[ 3.310022] 21f4000.serial: ttymxc4 at MMIO 0x21f4000 (irq = 270,
base_baud = 5000000) is a IMX
[ 3.339597] panel-simple panel: supply power not found, using dummy regulator
[ 3.365682] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops)
[ 3.372400] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops)
[ 3.378114] etnaviv-gpu 130000.gpu: model: GC880, revision: 5106
[ 3.385550] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007
[ 3.395114] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0
[ 3.409334] imx-ipuv3 2400000.ipu: IPUv3H probed
[ 3.456061] brd: module loaded
[ 3.491073] loop: module loaded
[ 3.506529] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xd3
[ 3.512923] nand: Winbond W29N08GV
[ 3.516421] nand: 1024 MiB, SLC, erase size: 128 KiB, page size:
2048, OOB size: 64
[ 3.525991] Bad block table found at page 524224, version 0x01
[ 3.532422] Bad block table found at page 524160, version 0x01
[ 3.538885] 6 cmdlinepart partitions found on MTD device gpmi-nand
[ 3.545094] Creating 6 MTD partitions on "gpmi-nand":
[ 3.550240] 0x000000000000-0x000000200000 : "spl"
[ 3.566776] 0x000000200000-0x000000400000 : "uboot"
[ 3.579186] 0x000000400000-0x000000500000 : "env"
[ 3.591520] 0x000000500000-0x000001500000 : "kernel"
[ 3.604423] 0x000001500000-0x000001600000 : "dtb"
[ 3.618303] 0x000001600000-0x000040000000 : "rootfs"
[ 3.659665] gpmi-nand 112000.nand-controller: driver registered.
[ 3.666959] SPI driver spidev has no spi_device_id for ltts,evalspi
[ 3.686253] CAN device driver interface
[ 3.702126] pps pps0: new PPS source ptp0
[ 3.709056] fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00
[ 3.715988] fec 2188000.ethernet: Using random MAC address: 86:d6:01:18:ff:de
[ 3.733304] fec 2188000.ethernet eth0: registered PHC device 0
[ 3.741777] usbcore: registered new interface driver r8152
[ 3.747648] usbcore: registered new interface driver lan78xx
[ 3.753513] usbcore: registered new interface driver asix
[ 3.759328] usbcore: registered new interface driver ax88179_178a
[ 3.765791] usbcore: registered new interface driver cdc_ether
[ 3.771827] usbcore: registered new interface driver smsc95xx
[ 3.777918] usbcore: registered new interface driver net1080
[ 3.783727] usbcore: registered new interface driver cdc_subset
[ 3.789881] usbcore: registered new interface driver zaurus
[ 3.795672] usbcore: registered new interface driver MOSCHIP
usb-ethernet driver
[ 3.803385] usbcore: registered new interface driver cdc_ncm
[ 3.809271] usbcore: registered new interface driver r8153_ecm
[ 3.815506] usbcore: registered new interface driver usb-storage
[ 3.831006] SPI driver ads7846 has no spi_device_id for ti,tsc2046
[ 3.837316] SPI driver ads7846 has no spi_device_id for ti,ads7843
[ 3.843521] SPI driver ads7846 has no spi_device_id for ti,ads7845
[ 3.849776] SPI driver ads7846 has no spi_device_id for ti,ads7873
[ 4.445853] input: ILI210x Touchscreen as
/devices/platform/soc/2100000.bus/21a0000.i2c/i2c-0/0-0041/input/input0
[ 4.463608] pwm-beeper buzzer: supply amp not found, using dummy regulator
[ 4.471904] input: pwm-beeper as /devices/platform/buzzer/input/input1
[ 4.489945] rtc-rv3032 2-0051: registered as rtc0
[ 4.495855] rtc-rv3032 2-0051: hctosys: unable to read the hardware clock
[ 4.508809] hwmon hwmon0: temp1_input not attached to any thermal zone
[ 4.521570] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc1
[ 4.528373] i2c_dev: i2c /dev entries driver
[ 4.549409] Bluetooth: HCI UART driver ver 2.3
[ 4.553894] Bluetooth: HCI UART protocol H4 registered
[ 4.559248] Bluetooth: HCI UART protocol LL registered
[ 4.564605] usbcore: registered new interface driver btusb
[ 4.573887] sdhci: Secure Digital Host Controller Interface driver
[ 4.580184] sdhci: Copyright(c) Pierre Ossman
[ 4.584567] sdhci-pltfm: SDHCI platform and OF driver helper
[ 4.594237] sdhci-esdhc-imx 2190000.mmc: Got CD GPIO
[ 4.608457] caam 2100000.crypto: Entropy delay = 3200
[ 4.674334] caam 2100000.crypto: Instantiated RNG4 SH0
[ 4.735099] caam 2100000.crypto: Instantiated RNG4 SH1
[ 4.745853] caam 2100000.crypto: device ID = 0x0a16010000000100 (Era 4)
[ 4.752569] caam 2100000.crypto: job rings = 2, qi = 0
[ 4.766963] caam algorithms registered in /proc/crypto
[ 4.772822] caam 2100000.crypto: registering rng-caam
[ 4.786217] mmc0: SDHCI controller on 2190000.mmc [2190000.mmc] using ADMA
[ 4.797221] caam 2100000.crypto: rng crypto API alg registered prng-caam
[ 4.810644] usbcore: registered new interface driver usbhid
[ 4.816367] usbhid: USB HID core driver
[ 4.826100] imx-ipuv3-csi imx-ipuv3-csi.0: Registered ipu1_csi0
capture as /dev/video0
[ 4.836462] imx-ipuv3 2400000.ipu: Registered ipu1_ic_prpenc
capture as /dev/video1
[ 4.845191] imx-ipuv3 2400000.ipu: Registered ipu1_ic_prpvf capture
as /dev/video2
[ 4.854918] imx-ipuv3-csi imx-ipuv3-csi.1: Registered ipu1_csi1
capture as /dev/video3
[ 4.871518] mmc0: host does not support reading read-only switch,
assuming write-enable
[ 4.887794] mmc0: new high speed SDHC card at address 0001
[ 4.907708] mmcblk0: mmc0:0001 USD 7.44 GiB
[ 4.923964] NET: Registered PF_INET6 protocol family
[ 4.938124] mmcblk0: p1 p2 p3
[ 4.949653] Segment Routing with IPv6
[ 4.953421] In-situ OAM (IOAM) with IPv6
[ 4.958277] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 4.967245] NET: Registered PF_PACKET protocol family
[ 4.973235] can: controller area network core
[ 4.978040] NET: Registered PF_CAN protocol family
[ 4.982948] can: raw protocol
[ 4.986206] random: crng init done
[ 4.989816] can: broadcast manager protocol
[ 4.994071] can: netlink gateway - max_hops=1
[ 4.999596] Key type dns_resolver registered
[ 5.016720] Registering SWP/SWPB emulation handler
[ 5.022738] Loading compiled-in X.509 certificates
[ 5.204409] Stack Depot allocating hash table of 65536 entries with kvcalloc
[ 5.216619] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops
ipu_crtc_ops)
[ 5.224503] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops
ipu_crtc_ops)
[ 5.232738] imx-drm display-subsystem: bound ldb (ops imx_ldb_ops)
[ 5.242432] [drm] Initialized imx-drm 1.0.0 20120507 for
display-subsystem on minor 1
[ 5.336982] Console: switching to colour frame buffer device 160x50
[ 5.363752] imx-drm display-subsystem: [drm] fb0: imx-drmdrmfb
frame buffer device
[ 5.997424] mxs_phy 20c9000.usbphy: Data pin can't make good contact.
[ 6.013128] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 6.018536] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[ 6.055398] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 6.062453] usb usb1: New USB device found, idVendor=1d6b,
idProduct=0002, bcdDevice= 6.01
[ 6.071010] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 6.078308] usb usb1: Product: EHCI Host Controller
[ 6.083208] usb usb1: Manufacturer: Linux 6.1.58 ehci_hcd
[ 6.089002] usb usb1: SerialNumber: ci_hdrc.1
[ 6.098174] hub 1-0:1.0: USB hub found
[ 6.102309] hub 1-0:1.0: 1 port detected
[ 6.113416] video-mux 20e0000.iomuxc-gpr:ipu1_csi0_mux: Consider
updating driver video-mux to match on endpoints
[ 6.126877] video-mux 20e0000.iomuxc-gpr:ipu1_csi1_mux: Consider
updating driver video-mux to match on endpoints
[ 6.145163] imx-media: Registered ipu_ic_pp csc/scaler as /dev/video4
[ 6.156758] imx_thermal 20c8000.anatop:tempmon: Extended Commercial
CPU temperature grade - max:105C critical:100C passive:95C
[ 6.181973] cfg80211: Loading compiled-in X.509 certificates for
regulatory database
[ 6.196443] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 6.204613] platform regulatory.0: Direct firmware load for
regulatory.db failed with error -2
[ 6.213542] platform regulatory.0: Falling back to sysfs fallback
for: regulatory.db
[ 6.224065] ALSA device list:
[ 6.230889] No soundcards found.
[ 6.271484] EXT4-fs (mmcblk0p2): mounted filesystem with ordered
data mode. Quota mode: none.
[ 6.281110] VFS: Mounted root (ext4 filesystem) on device 179:2.
[ 6.289875] devtmpfs: mounted
[ 6.295188] Freeing unused kernel image (initmem) memory: 1024K
[ 6.302075] Run /sbin/init as init process
[ 6.395409] usb 1-1: new high-speed USB device number 2 using ci_hdrc
[ 6.598005] usb 1-1: New USB device found, idVendor=0451,
idProduct=8142, bcdDevice= 1.00
[ 6.606485] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=1
[ 6.613748] usb 1-1: SerialNumber: EA030849138F
[ 6.628789] hub 1-1:1.0: USB hub found
[ 6.633391] hub 1-1:1.0: 4 ports detected
[ 6.772078] systemd[1]: System time before build time, advancing clock.
[ 6.900824] systemd[1]: systemd 250.5+ running in system mode (-PAM
-AUDIT -SELINUX -APPARMOR +IMA -SMACK +SECCOMP -GCRYPT -GNUTLS
-OPENSSL +ACL +BLKID -CURL -ELFUTILS -FIDO2 -IDN2 -IDN -IPTC +KMOD
-LIBCRYPTSETUP +LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -BZIP2
-LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT
default-hierarchy=hybrid)
[ 6.934384] systemd[1]: Detected architecture arm.
Welcome to FSLC FrameBuffer [ 6.955469] usb 1-1.1: new high-speed
USB device number 3 using ci_hdrc
4.0 (kirkstone)!
[ 6.987732] systemd[1]: Hostname set to <ltts-imx6solo>.
[ 7.002838] systemd[1]: Initializing machine ID from random generator.
[ 7.107401] usb 1-1.1: New USB device found, idVendor=04b4,
idProduct=bd30, bcdDevice= 1.00
[ 7.116088] usb 1-1.1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 7.138412] hub 1-1.1:1.0: USB hub found
[ 7.145842] hub 1-1.1:1.0: 2 ports detected
[ 7.575615] usb 1-1.1.1: new high-speed USB device number 4 using ci_hdrc
[ 7.747978] usb 1-1.1.1: New USB device found, idVendor=04b4,
idProduct=bd29, bcdDevice= 0.01
[ 7.756770] usb 1-1.1.1: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 7.764382] usb 1-1.1.1: Product: Remote Download Wireless Adapter
[ 7.770725] usb 1-1.1.1: Manufacturer: Cypress Semiconductor Corp.
[ 7.776982] usb 1-1.1.1: SerialNumber: 000000000001
[ 7.905545] usb 1-1.1.2: new high-speed USB device number 5 using ci_hdrc
[ 8.067618] usb 1-1.1.2: New USB device found, idVendor=04b4,
idProduct=640c, bcdDevice= 1.12
[ 8.076399] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 8.083962] usb 1-1.1.2: Product: BCM2045A0
[ 8.088278] usb 1-1.1.2: Manufacturer: Cypress Semiconductor Corp.
[ 8.094481] usb 1-1.1.2: SerialNumber: C0EE40822FFD
[ 8.115037] Bluetooth: : invalid diagnostic descriptors
[ 8.258777] Bluetooth: hci0: BCM: chip id 135
[ 8.264757] Bluetooth: hci0: BCM: features 0x0f
[ 8.270748] Bluetooth: hci0: BCM4373A0
[ 8.274527] Bluetooth: hci0: BCM (001.001.025) build 0000
[ 8.586409] systemd[1]: Queued start job for default target
Multi-User System.
[ 8.603805] systemd[1]: Created slice Slice /system/getty.
[ OK ] Created slice Slice /system/getty.
[ 8.648833] systemd[1]: Created slice Slice /system/modprobe.
[ OK ] Created slice Slice /system/modprobe.
[ 8.688774] systemd[1]: Created slice Slice /system/serial-getty.
[ OK ] Created slice Slice /system/serial-getty.
[ 8.727817] systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
[ 8.766815] systemd[1]: Started Dispatch Password Requests to
Console Directory Watch.
[ OK ] Started Dispatch Password …ts to Console Directory Watch.
[ 8.806596] systemd[1]: Started Forward Password Requests to Wall
Directory Watch.
[ OK ] Started Forward Password R…uests to Wall Directory Watch.
[ 8.846133] systemd[1]: Reached target Remote File Systems.
[ OK ] Reached target Remote File Systems.
[ 8.885810] systemd[1]: Reached target Slice Units.
[ OK ] Reached target Slice Units.
[ 8.915823] systemd[1]: Reached target Swaps.
[ OK ] Reached target Swaps.
[ 9.039331] systemd[1]: Listening on RPCbind Server Activation Socket.
[ OK ] Listening on RPCbind Server Activation Socket.
[ 9.075978] systemd[1]: Reached target RPC Port Mapper.
[ OK ] Reached target RPC Port Mapper.
[ 9.118117] systemd[1]: Listening on Syslog Socket.
[ OK ] Listening on Syslog Socket.
[ 9.157256] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ 9.209924] systemd[1]: Journal Audit Socket was skipped because of
a failed condition check (ConditionSecurity=audit).
[ 9.222922] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 9.267869] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 9.307376] systemd[1]: Listening on Network Service Netlink Socket.
[ OK ] Listening on Network Service Netlink Socket.
[ 9.348009] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 9.387020] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 9.427590] systemd[1]: Listening on User Database Manager Socket.
[ OK ] Listening on User Database Manager Socket.
[ 9.467036] systemd[1]: Huge Pages File System was skipped because
of a failed condition check
(ConditionPathExists=/sys/kernel/mm/hugepages).
[ 9.481016] systemd[1]: POSIX Message Queue File System was skipped
because of a failed condition check
(ConditionPathExists=/proc/sys/fs/mqueue).
[ 9.527378] systemd[1]: Mounting Kernel Debug File System...
Mounting Kernel Debug File System...
[ 9.558506] systemd[1]: Mounting Kernel Trace File System...
Mounting Kernel Trace File System...
[ 9.616712] systemd[1]: Mounting Temporary Directory /tmp...
Mounting Temporary Directory /tmp...
[ 9.656702] systemd[1]: Create List of Static Device Nodes was
skipped because of a failed condition check
(ConditionFileNotEmpty=/lib/modules/6.1.58/modules.devname).
[ 9.707567] systemd[1]: Starting Load Kernel Module configfs...
Starting Load Kernel Module configfs...
[ 9.751753] systemd[1]: Starting Load Kernel Module drm...
Starting Load Kernel Module drm...
[ 9.798167] systemd[1]: Starting Load Kernel Module fuse...
Starting Load Kernel Module fuse...
[ 9.832532] systemd[1]: Starting RPC Bind...
Starting RPC Bind...
[ 9.886356] systemd[1]: File System Check on Root Device was
skipped because of a failed condition check
(ConditionPathIsReadWrite=!/).
[ 9.957558] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 9.988890] systemd[1]: Load Kernel Modules was skipped because all
trigger condition checks failed.
[ 10.042346] systemd[1]: Starting Generate network units from Kernel
command line...
Starting Generate network …ts from Kernel command line...
[ 10.133724] systemd[1]: Starting Remount Root and Kernel File Systems...
Starting Remount Root and Kernel File Systems...
[ 10.243537] systemd[1]: Starting Apply Kernel Variables...
Starting Apply Kernel Variables...
[ 10.343465] systemd[1]: Starting Coldplug All udev Devices...
[ 10.374405] EXT4-fs (mmcblk0p2): re-mounted. Quota mode: none.
Starting Coldplug All udev Devices...
[ 10.534913] systemd[1]: Started RPC Bind.
[ OK ] Started RPC Bind.
[ 10.608027] systemd[1]: Mounted Kernel Debug File System.
[ OK ] Mounted Kernel Debug File System.
[ 10.637271] systemd[1]: Mounted Kernel Trace File System.
[ OK ] Mounted Kernel Trace File System.
[ 10.657321] systemd[1]: Mounted Temporary Directory /tmp.
[ OK ] Mounted Temporary Directory /tmp.
[ 10.681203] systemd[1]: [email protected]: Deactivated successfully.
[ 10.737464] systemd[1]: Finished Load Kernel Module configfs.
[ OK ] Finished Load Kernel Module configfs.
[ 10.760018] systemd[1]: [email protected]: Deactivated successfully.
[ 10.806004] systemd[1]: Finished Load Kernel Module drm.
[ OK ] Finished Load Kernel Module drm.
[ 10.849819] systemd[1]: [email protected]: Deactivated successfully.
[ 10.886052] systemd[1]: Finished Load Kernel Module fuse.
[ OK ] Finished Load Kernel Module fuse.
[ 10.936205] systemd[1]: Finished Generate network units from Kernel
command line.
[ OK ] Finished Generate network units from Kernel command line.
[ 10.969049] systemd[1]: Finished Remount Root and Kernel File Systems.
[ OK ] Finished Remount Root and Kernel File Systems.
[ 11.036198] systemd[1]: Finished Apply Kernel Variables.
[ OK ] Finished Apply Kernel Variables.
[ 11.087501] systemd[1]: Mounting FUSE Control File System...
Mounting FUSE Control File System...
[ 11.176360] systemd[1]: Mounting Kernel Configuration File System...
Mounting Kernel Configuration File System...
[ 11.215767] systemd[1]: Rebuild Hardware Database was skipped
because all trigger condition checks failed.
[ 11.251767] systemd[1]: Platform Persistent Storage Archival was
skipped because of a failed condition check
(ConditionDirectoryNotEmpty=/sys/fs/pstore).
[ 11.328008] systemd[1]: Starting Create System Users...
Starting Create System Users...
[ 11.364934] systemd[1]: Mounted FUSE Control File System.
[ OK ] Mounted FUSE Control File System.
[ 11.497676] systemd[1]: Mounted Kernel Configuration File System.
[ OK ] Mounted Kernel Configuration File System.
[ 11.646076] systemd[1]: Finished Create System Users.
[ OK ] Finished Create System Users.
[ 11.713902] systemd[1]: Starting Create Static Device Nodes in /dev...
Starting Create Static Device Nodes in /dev...
[ 11.874042] systemd[1]: Started Journal Service.
[ OK ] Started Journal Service.
Starting Flush Journal to Persistent Storage...
[ OK ] Finished Create Static Device Nodes in /dev.
[ OK ] Reached target Preparation for Local File Systems.
[ 12.106123] systemd-journald[189]: Received client request to flush
runtime journal.
Mounting /var/volatile...
Starting Rule-based Manage…for Device Events and Files...
[ OK ] Finished Flush Journal to Persistent Storage.
[ OK ] Mounted /var/volatile.
Starting Load/Save Random Seed...
[ OK ] Reached target Local File Systems.
Starting Rebuild Dynamic Linker Cache...
Starting Create Volatile Files and Directories...
[ OK ] Finished Load/Save Random Seed.
[ OK ] Started Rule-based Manager for Device Events and Files.
[ OK ] Finished Create Volatile Files and Directories.
Starting Rebuild Journal Catalog...
Starting Network Time Synchronization...
Starting Record System Boot/Shutdown in UTMP...
[ OK ] Finished Record System Boot/Shutdown in UTMP.
[ OK ] Finished Rebuild Journal Catalog.
[ 16.493054] platform 2008000.spi: deferred probe pending
[ 16.499144] platform 200c000.spi: deferred probe pending
[ OK ] Finished Rebuild Dynamic Linker Cache.
Starting Update is Completed...
[ OK ] Started Network Time Synchronization.
[ OK ] Reached target System Time Set.
[ OK ] Finished Update is Completed.
[ OK ] Created slice Slice /system/systemd-backlight.
Starting Load/Save Screen …of backlight:backlight-lvds...
[ 18.799032] mtdblock: MTD device 'spl' is NAND, please consider
using UBI block devices instead.
[ 18.816735] mtdblock: MTD device 'env' is NAND, please consider
using UBI block devices instead.
[ 18.828089] mtdblock: MTD device 'uboot' is NAND, please consider
using UBI block devices instead.
[ OK ] Finished Load/Save Screen …s of backlight:backlight-lvds.
[ 18.876158] mtdblock: MTD device 'kernel' is NAND, please consider
using UBI block devices instead.
[ 19.041189] mtdblock: MTD device 'dtb' is NAND, please consider
using UBI block devices instead.
[ 19.110839] mtdblock: MTD device 'rootfs' is NAND, please consider
using UBI block devices instead.
[ OK ] Finished Coldplug All udev Devices.
[ 19.724404] coda 2040000.vpu: Firmware code revision: 46076
[ 19.730290] coda 2040000.vpu: Initialized CODA960.
[ 19.735106] coda 2040000.vpu: Firmware version: 3.1.1
[ OK ] Reached target System Initialization.
[ OK ] Started CUPS Scheduler.
[ 19.976908] coda 2040000.vpu: coda-jpeg-encoder registered as video5
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Reached target Path Units.
[ OK ] Reached target Timer Units.
[ 20.070627] coda 2040000.vpu: coda-jpeg-decoder registered as video6
[ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
[ 20.152447] coda 2040000.vpu: coda-video-encoder registered as video7
[ 20.209677] coda 2040000.vpu: coda-video-decoder registered as video8
[ 20.338632] switch@0 enforce active low on chipselect handle
[ OK ] Listening on [ 20.369744] imx-sdma 20ec000.dma-controller:
loaded firmware 3.5
CUPS LPD Server Socket.
[ OK ] Listening on CUPS Scheduler.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Socket Units.
[ OK ] Reached target Basic System.
[ OK ] Started Kernel Logging Service.
[ OK ] Started System Logging Service.
Starting D-Bus System Message Bus...
[ OK ] Started Getty on tty1.
Starting IPv6 Packet Filtering Framework...
Starting IPv4 Packet Filtering Framework...
Starting Turn OFF RGB LED...
Starting Telephony service...
[ OK ] Started Serial Getty on ttymxc1.
[ 22.118482] brcmfmac: brcmf_fw_alloc_request: using
brcm/brcmfmac4373 for chip BCM4373/0
[ OK ] Reached target Login Prompts.
[ 22.318014] usbcore: registered new interface driver brcmfmac
Starting User Login Management...
[ OK ] Started D-Bus System Message Bus.
[ OK ] Finished IPv6 Packet Filtering Framework.
[ OK ] Finished IPv4 Packet Filtering Framework.
[ OK ] Finished Turn OFF RGB LED.
[ 25.296596] sja1105 spi1.0: Probed switch chip: SJA1105Q
[ 25.567725] sja1105 spi1.0: configuring for fixed/mii link mode
[ 25.646176] sja1105 spi1.0 ethphy0 (uninitialized): PHY
[2188000.ethernet-1:00] driver [TI DP83848C 10/100 Mbps PHY]
(irq=POLL)
[ OK ] Started Telephony service.
[ 25.805638] sja1105 spi1.0 ethphy1 (uninitialized): PHY
[2188000.ethernet-1:01] driver [TI DP83848C 10/100 Mbps PHY]
(irq=POLL)
[ 25.925915] device eth0 entered promiscuous mode
[ 25.930974] DSA: tree 0 setup
FSLC FrameBuffer 4.0 ltts-imx6solo ttymxc1
ltts-imx6solo login: [ 27.736803] usb 1-1.1.1: USB disconnect, device number 4
[ 27.844068] brcmfmac: brcmf_usb_dl_cmd: usb_submit_urb failed -19
[ 27.936752] sja1105 spi1.0: Link is Up - 100Mbps/Full - flow control off
[ 28.235476] usb 1-1.1.1: new high-speed USB device number 6 using ci_hdrc
[ 28.418004] usb 1-1.1.1: New USB device found, idVendor=04b4,
idProduct=0bdc, bcdDevice= 0.01
[ 28.426753] usb 1-1.1.1: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 28.434317] usb 1-1.1.1: Product: Cypress USB 802.11 Wireless Adapter
[ 28.440924] usb 1-1.1.1: Manufacturer: Cypress Semiconductor Corp.
[ 28.447196] usb 1-1.1.1: SerialNumber: 000000000001
[ 28.565571] brcmfmac: brcmf_fw_alloc_request: using
brcm/brcmfmac4373 for chip BCM4373/0
[ 28.627016] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4373/0
wl0: Nov 16 2022 23:54:18 version 13.10.246.300 (ed9caf7 CY) FWID
01-3b88916b
[ 29.486120] Generic PHY fixed-0:00: attached PHY driver
(mii_bus:phy_addr=fixed-0:00, irq=POLL)
[ 29.497422] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full -
flow control off
[ 29.623164] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 29.637065] Bluetooth: BNEP socket layer initialized
[ 29.836814] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 69.610610] cfg80211: failed to load regulatory.db
[ 69.620405] Bluetooth: hci0: BCM 'brcm/BCM-04b4-640c.hcd' Patch
[ 70.347701] Bluetooth: hci0: BCM: features 0x0f
[ 70.353703] Bluetooth: hci0: CYW94373 UART 37.4MHz Class 1 wlbga sLNA-0102
[ 70.360747] Bluetooth: hci0: BCM (001.001.025) build 0149
[ 70.422010] Bluetooth: MGMT ver 1.22
ltts-imx6solo login: root
root@ltts-imx6solo:~# cat /usr/phynew.sh
#!/bin/sh
echo ======= MDIO: PHY0 ========
mdio 2188000.ethernet-1 phy 0 raw 0x0
mdio 2188000.ethernet-1 phy 0 raw 0x1
mdio 2188000.ethernet-1 phy 0 raw 0x2
mdio 2188000.ethernet-1 phy 0 raw 0x3
mdio 2188000.ethernet-1 phy 0 raw 0x4
mdio 2188000.ethernet-1 phy 0 raw 0x5
mdio 2188000.ethernet-1 phy 0 raw 0x6
mdio 2188000.ethernet-1 phy 0 raw 0x7
mdio 2188000.ethernet-1 phy 0 raw 0x10
mdio 2188000.ethernet-1 phy 0 raw 0x19
echo ======= MDIO: PHY1 ========
mdio 2188000.ethernet-1 phy 1 raw 0x0
mdio 2188000.ethernet-1 phy 1 raw 0x1
mdio 2188000.ethernet-1 phy 1 raw 0x2
mdio 2188000.ethernet-1 phy 1 raw 0x3
mdio 2188000.ethernet-1 phy 1 raw 0x4
mdio 2188000.ethernet-1 phy 1 raw 0x5
mdio 2188000.ethernet-1 phy 1 raw 0x6
mdio 2188000.ethernet-1 phy 1 raw 0x7
mdio 2188000.ethernet-1 phy 1 raw 0x10
mdio 2188000.ethernet-1 phy 1 raw 0x19
ip link set dev eth0 down
ip link set dev ethphy0 down
ip link set dev ethphy1 down
ip link set dev ethphy0 address 00:11:22:33:44:55
ip link set dev ethphy1 address 00:11:22:33:44:66
ip addr add dev ethphy0 169.254.178.1/16
ip addr add dev ethphy1 169.253.178.2/16
ip link set dev eth0 up
ip link set dev ethphy0 up
ip link set dev ethphy1 up
ip link
echo ########## MDIO: PHY0 ###########
mdio 2188000.ethernet-1 phy 0 raw 0x0
mdio 2188000.ethernet-1 phy 0 raw 0x1
mdio 2188000.ethernet-1 phy 0 raw 0x2
mdio 2188000.ethernet-1 phy 0 raw 0x3
mdio 2188000.ethernet-1 phy 0 raw 0x4
mdio 2188000.ethernet-1 phy 0 raw 0x5
mdio 2188000.ethernet-1 phy 0 raw 0x6
mdio 2188000.ethernet-1 phy 0 raw 0x7
mdio 2188000.ethernet-1 phy 0 raw 0x10
mdio 2188000.ethernet-1 phy 0 raw 0x19
echo ########## MDIO: PHY1 ###########
mdio 2188000.ethernet-1 phy 1 raw 0x0
mdio 2188000.ethernet-1 phy 1 raw 0x1
mdio 2188000.ethernet-1 phy 1 raw 0x2
mdio 2188000.ethernet-1 phy 1 raw 0x3
mdio 2188000.ethernet-1 phy 1 raw 0x4
mdio 2188000.ethernet-1 phy 1 raw 0x5
mdio 2188000.ethernet-1 phy 1 raw 0x6
mdio 2188000.ethernet-1 phy 1 raw 0x7
mdio 2188000.ethernet-1 phy 1 raw 0x10
mdio 2188000.ethernet-1 phy 1 raw 0x19
root@ltts-imx6solo:~# bash /usr/phynew.sh
======= MDIO: PHY0 ========
[ 162.426515] mdio_netlink: loading out-of-tree module taints kernel.
0x3100
0x7869
0x2000
0x5ca2
0x01e1
0x45e1
0x0007
0x2801
0x4015
0x8020
======= MDIO: PHY1 ========
0x3100
0x7869
0x2000
0x5ca2
0x01e1
0x45e1
0x0007
0x2801
0x0015
0x8021
[ 162.992201] Generic PHY fixed-0:00: attached PHY driver
(mii_bus:phy_addr=fixed-0:00, irq=POLL)
[ 163.002179] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full -
flow control off
[ 163.035906] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 163.074193] sja1105 spi1.0 ethphy0: configuring for phy/mii link mode
[ 163.144909] sja1105 spi1.0 ethphy1: configuring for phy/mii link mode
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
mode DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1504 qdisc pfifo_fast
state UP mode DEFAULT group default qlen 1000
link/ether 6a:fb:08:df:d3:77 brd ff:ff:ff:ff:ff:ff
3: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT
group default qlen 1000
link/sit 0.0.0.0 brd 0.0.0.0
4: ethphy0@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc
noqueue state LOWERLAYERDOWN mode DEFAULT group default qlen 1000
link/ether 00:11:22:33:44:55 brd ff:ff:ff:ff:ff:ff
5: ethphy1@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc
noqueue state LOWERLAYERDOWN mode DEFAULT group default qlen 1000
link/ether 00:11:22:33:44:66 brd ff:ff:ff:ff:ff:ff
6: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
link/ether c0:ee:40:82:2f:fc brd ff:ff:ff:ff:ff:ff
0x3100
0x7849
0x2000
0x5ca2
0x0141
0x0000
0x0005
0x2801
0x4000
0x8020
0x3100
0x7849
0x2000
0x5ca2
0x0141
0x0000
0x0005
0x2801
0x0000
0x8021
root@ltts-imx6solo:~# [ 165.208656] sja1105 spi1.0 ethphy0: Link is
Up - 100Mbps/Full - flow control off
[ 165.225788] sja1105 spi1.0 ethphy1: Link is Up - 100Mbps/Full -
flow control off
[ 165.235925] IPv6: ADDRCONF(NETDEV_CHANGE): ethphy0: link becomes ready
[ 165.255777] IPv6: ADDRCONF(NETDEV_CHANGE): ethphy1: link becomes ready
root@ltts-imx6solo:~# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1504
inet6 fe80::68fb:8ff:fedf:d377 prefixlen 64 scopeid 0x20<link>
ether 6a:fb:08:df:d3:77 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
ethphy0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 169.254.178.1 netmask 255.255.0.0 broadcast 0.0.0.0
inet6 fe80::211:22ff:fe33:4455 prefixlen 64 scopeid 0x20<link>
ether 00:11:22:33:44:55 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 30 bytes 4071 (3.9 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
ethphy1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 169.253.178.2 netmask 255.255.0.0 broadcast 0.0.0.0
inet6 fe80::211:22ff:fe33:4466 prefixlen 64 scopeid 0x20<link>
ether 00:11:22:33:44:66 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 30 bytes 4071 (3.9 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 89 bytes 7675 (7.4 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 89 bytes 7675 (7.4 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
mytsl02383@MYTSL02383:~$ ifconfig -a
enp43s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 169.254.178.2 netmask 255.255.0.0 broadcast 169.254.255.255
inet6 fe80::d71b:4bdd:27bd:2a1a prefixlen 64 scopeid 0x20<link>
ether 00:be:43:20:9a:26 txqueuelen 1000 (Ethernet)
RX packets 272356 bytes 27099064 (27.0 MB)
RX errors 0 dropped 19 overruns 0 frame 0
TX packets 862 bytes 300806 (300.8 KB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
mytsl02383@MYTSL02383:~$ ping 169.254.178.1
PING 169.254.178.1 (169.254.178.1) 56(84) bytes of data.
From 169.254.178.2 icmp_seq=1 Destination Host Unreachable
Let me know if you need any more details.
Thanks,
Jagan.
On Fri, Dec 29, 2023 at 05:12:39PM +0530, Jagan Teki wrote:
> With fec0 fixed-link and 3 different switch port configurations, the
> result of the link seems to be up but the ping not working and even
> the packets are not transmitted via eth0.
>
> DT Combinations:
>
> - Port0 is ethphy0, Port1 is ethphy1, Port2 is disabled, Port3 is
> disabled, Port4 is FEC
> - Port0 is disabled, Port1 is ethphy0, Port2 is ethphy1, Port3 is
> disabled, Port4 is FEC
> - Port0 is disabled, Port1 is disabled, Port2 is ethphy0, Port3 is
> ethphy1, Port4 as FEC
Why all these combinations? You don't know which switch port is which?
> DT: (with Port0 is ethphy0, Port1 is ethphy1, Port2 is disabled, Port3
> is disabled, Port4 is FEC)
>
> &ecspi2 {
> cs-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>;
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_ecspi2>;
> status = "okay";
>
> switch@0 {
> compatible = "nxp,sja1105q";
> reg = <0>;
> spi-max-frequency = <4000000>;
> spi-rx-delay-us = <1>;
> spi-tx-delay-us = <1>;
> spi-cpha;
>
> clocks = <&clk25m>;
>
> pinctrl-0 = <&pinctrl_sja1105_rst>;
> pinctrl-names = "default";
> reset-gpios = <&gpio6 5 GPIO_ACTIVE_LOW>;
>
> ports {
> #address-cells = <1>;
> #size-cells = <0>;
>
> port@0 {
> reg = <0>;
> label = "ethphy0";
> phy-handle = <ðphy0>;
> phy-mode = "mii";
> };
>
> port@1 {
> reg = <1>;
> label = "ethphy1";
> phy-handle = <ðphy1>;
> phy-mode = "mii";
> };
>
> port@2 {
> reg = <2>;
> status = "disabled";
> };
>
> port@3 {
> reg = <3>;
> status = "disabled";
> };
>
> port@4 {
> reg = <4>;
> label = "cpu";
> ethernet = <&fec>;
> phy-mode = "mii";
> rx-internal-delay-ps = <2000>;
> tx-internal-delay-ps = <2000>;
This looks suspicious. "rx-internal-delay-ps" and "tx-internal-delay-ps"
are only relevant for the RGMII modes, but you specify phy-mode = "mii".
Does the board schematic confirm that MII is the physical connection
being used from the switch to the FEC?
If you are truly using MII, then you should remove the RGMII delay
properties, and since you are using a 6.1 kernel - hence after kernel
commit 5d645df99ac6 ("net: dsa: sja1105: determine PHY/MAC role from PHY
interface type") - you should be using phy-mode = "rev-mii" to put this
port in MII PHY ("RevMII") mode - to interoperate with the FEC in MII
MAC mode.
>
> fixed-link {
> speed = <100>;
> full-duplex;
> };
> };
> };
> };
> };
>
> &fec {
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_enet>;
> phy-mode = "mii";
> status = "okay";
>
> fixed-link {
> speed = <100>;
> full-duplex;
> };
>
> mdio {
> #address-cells = <1>;
> #size-cells = <0>;
>
> ethphy0: ethernet-phy@0 {
> compatible = "ethernet-phy-ieee802.3-c22";
> reg = <0>;
> };
>
> ethphy1: ethernet-phy@1 {
> compatible = "ethernet-phy-ieee802.3-c22";
> reg = <1>;
> };
> };
> };
>
> root@ltts-imx6solo:~# bash /usr/phynew.sh
> ======= MDIO: PHY0 ========
> [ 162.426515] mdio_netlink: loading out-of-tree module taints kernel.
Still, please refrain from involving out-of-tree modules when asking for
help upstream. Thanks.
> root@ltts-imx6solo:~# [ 165.208656] sja1105 spi1.0 ethphy0: Link is
> Up - 100Mbps/Full - flow control off
> [ 165.225788] sja1105 spi1.0 ethphy1: Link is Up - 100Mbps/Full -
> flow control off
> [ 165.235925] IPv6: ADDRCONF(NETDEV_CHANGE): ethphy0: link becomes ready
> [ 165.255777] IPv6: ADDRCONF(NETDEV_CHANGE): ethphy1: link becomes ready
>
> root@ltts-imx6solo:~# ifconfig
> eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1504
> inet6 fe80::68fb:8ff:fedf:d377 prefixlen 64 scopeid 0x20<link>
> ether 6a:fb:08:df:d3:77 txqueuelen 1000 (Ethernet)
> RX packets 0 bytes 0 (0.0 B)
> RX errors 0 dropped 0 overruns 0 frame 0
> TX packets 0 bytes 0 (0.0 B)
> TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
>
> ethphy0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
> inet 169.254.178.1 netmask 255.255.0.0 broadcast 0.0.0.0
> inet6 fe80::211:22ff:fe33:4455 prefixlen 64 scopeid 0x20<link>
> ether 00:11:22:33:44:55 txqueuelen 1000 (Ethernet)
> RX packets 0 bytes 0 (0.0 B)
> RX errors 0 dropped 0 overruns 0 frame 0
> TX packets 30 bytes 4071 (3.9 KiB)
> TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
>
> ethphy1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
> inet 169.253.178.2 netmask 255.255.0.0 broadcast 0.0.0.0
> inet6 fe80::211:22ff:fe33:4466 prefixlen 64 scopeid 0x20<link>
> ether 00:11:22:33:44:66 txqueuelen 1000 (Ethernet)
> RX packets 0 bytes 0 (0.0 B)
> RX errors 0 dropped 0 overruns 0 frame 0
> TX packets 30 bytes 4071 (3.9 KiB)
> TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
>
> lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
> inet 127.0.0.1 netmask 255.0.0.0
> inet6 ::1 prefixlen 128 scopeid 0x10<host>
> loop txqueuelen 1000 (Local Loopback)
> RX packets 89 bytes 7675 (7.4 KiB)
> RX errors 0 dropped 0 overruns 0 frame 0
> TX packets 89 bytes 7675 (7.4 KiB)
> TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
ifconfig reports statistics counters from the /proc/net/dev interface,
which the sja1105 does not report very well (they don't come from hardware).
It's best to use "ethtool -S eth0 | grep -v ': 0'" for FEC and SJA1105
CPU port (named "p04_*") counters, and "ethtool -S ethphy0 | grep -v ': 0'"
to get hardware counters from the switch user ports.
You can also use the RX counters to determine which switch port is which
(but the phy-handle of each port to each PHY needs to be correct).
> mytsl02383@MYTSL02383:~$ ifconfig -a
> enp43s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
> inet 169.254.178.2 netmask 255.255.0.0 broadcast 169.254.255.255
> inet6 fe80::d71b:4bdd:27bd:2a1a prefixlen 64 scopeid 0x20<link>
> ether 00:be:43:20:9a:26 txqueuelen 1000 (Ethernet)
> RX packets 272356 bytes 27099064 (27.0 MB)
> RX errors 0 dropped 19 overruns 0 frame 0
> TX packets 862 bytes 300806 (300.8 KB)
> TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
> mytsl02383@MYTSL02383:~$ ping 169.254.178.1
> PING 169.254.178.1 (169.254.178.1) 56(84) bytes of data.
> From 169.254.178.2 icmp_seq=1 Destination Host Unreachable
>
> Let me know if you need any more details.
I'm not convinced packets are routed through ethphy0 or ethphy1, since
all interfaces have IPv4 link-local addresses only. You can use
"ip route get 169.254.178.1" to confirm what interface gets chosen.
This is not indicative of a device-level problem, just a setup one.
Please set up some IPv4 static addresses which are not link-local on the
DSA user ports and try to ping a link partner which has an IP address in
the same subnet.
On Fri, Dec 29, 2023 at 8:55 PM Vladimir Oltean <[email protected]> wrote:
>
> On Fri, Dec 29, 2023 at 05:12:39PM +0530, Jagan Teki wrote:
> > With fec0 fixed-link and 3 different switch port configurations, the
> > result of the link seems to be up but the ping not working and even
> > the packets are not transmitted via eth0.
> >
> > DT Combinations:
> >
> > - Port0 is ethphy0, Port1 is ethphy1, Port2 is disabled, Port3 is
> > disabled, Port4 is FEC
> > - Port0 is disabled, Port1 is ethphy0, Port2 is ethphy1, Port3 is
> > disabled, Port4 is FEC
> > - Port0 is disabled, Port1 is disabled, Port2 is ethphy0, Port3 is
> > ethphy1, Port4 as FEC
>
> Why all these combinations? You don't know which switch port is which?
This is where I get confused in the first place. I didn't find proper
information on binding about how the physical pin-out is to be
configured in DT ports or maybe I didn't understand properly.
As per schematics.
Pin MII0_RXD0-D3/TXD0-D3 is connected to PROC_MII0_RXD0-D3/TXD0-D3
this would be fec0.
Pin MII1_RXD0-D3/TXD0-D3 is connected to PHY_MII1_RXD0-D3/TXD0-D3 this
would be ethphy0.
Pin MII2_RXD0-D3/TXD0-D3 is connected to PHY_MII2_RXD0-D3/TXD0-D3 this
would be ethphy1.
Pin MII3_RXD0-D3/TXD0-D3 is grounded
Pin MII4_RXD0-D3/TXD0-D3 is grounded
So, I did use the above 3 combinations and assumed fec0 is always a
port4 based on existing DTS in the tree. Please let me know which
configuration is proper as per schematic connections.
>
> > DT: (with Port0 is ethphy0, Port1 is ethphy1, Port2 is disabled, Port3
> > is disabled, Port4 is FEC)
> >
> > &ecspi2 {
> > cs-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>;
> > pinctrl-names = "default";
> > pinctrl-0 = <&pinctrl_ecspi2>;
> > status = "okay";
> >
> > switch@0 {
> > compatible = "nxp,sja1105q";
> > reg = <0>;
> > spi-max-frequency = <4000000>;
> > spi-rx-delay-us = <1>;
> > spi-tx-delay-us = <1>;
> > spi-cpha;
> >
> > clocks = <&clk25m>;
> >
> > pinctrl-0 = <&pinctrl_sja1105_rst>;
> > pinctrl-names = "default";
> > reset-gpios = <&gpio6 5 GPIO_ACTIVE_LOW>;
> >
> > ports {
> > #address-cells = <1>;
> > #size-cells = <0>;
> >
> > port@0 {
> > reg = <0>;
> > label = "ethphy0";
> > phy-handle = <ðphy0>;
> > phy-mode = "mii";
> > };
> >
> > port@1 {
> > reg = <1>;
> > label = "ethphy1";
> > phy-handle = <ðphy1>;
> > phy-mode = "mii";
> > };
> >
> > port@2 {
> > reg = <2>;
> > status = "disabled";
> > };
> >
> > port@3 {
> > reg = <3>;
> > status = "disabled";
> > };
> >
> > port@4 {
> > reg = <4>;
> > label = "cpu";
> > ethernet = <&fec>;
> > phy-mode = "mii";
> > rx-internal-delay-ps = <2000>;
> > tx-internal-delay-ps = <2000>;
>
> This looks suspicious. "rx-internal-delay-ps" and "tx-internal-delay-ps"
> are only relevant for the RGMII modes, but you specify phy-mode = "mii".
> Does the board schematic confirm that MII is the physical connection
> being used from the switch to the FEC?
Yes, the design uses MII.
>
> If you are truly using MII, then you should remove the RGMII delay
> properties, and since you are using a 6.1 kernel - hence after kernel
> commit 5d645df99ac6 ("net: dsa: sja1105: determine PHY/MAC role from PHY
> interface type") - you should be using phy-mode = "rev-mii" to put this
> port in MII PHY ("RevMII") mode - to interoperate with the FEC in MII
> MAC mode.
Okay, I will remove RGMII delay. is phy-mode = "rev-mii" applicable to
all ports or only for fec port4?
>
> >
> > fixed-link {
> > speed = <100>;
> > full-duplex;
> > };
> > };
> > };
> > };
> > };
> >
> > &fec {
> > pinctrl-names = "default";
> > pinctrl-0 = <&pinctrl_enet>;
> > phy-mode = "mii";
> > status = "okay";
> >
> > fixed-link {
> > speed = <100>;
> > full-duplex;
> > };
> >
> > mdio {
> > #address-cells = <1>;
> > #size-cells = <0>;
> >
> > ethphy0: ethernet-phy@0 {
> > compatible = "ethernet-phy-ieee802.3-c22";
> > reg = <0>;
> > };
> >
> > ethphy1: ethernet-phy@1 {
> > compatible = "ethernet-phy-ieee802.3-c22";
> > reg = <1>;
> > };
> > };
> > };
> >
> > root@ltts-imx6solo:~# bash /usr/phynew.sh
> > ======= MDIO: PHY0 ========
> > [ 162.426515] mdio_netlink: loading out-of-tree module taints kernel.
>
> Still, please refrain from involving out-of-tree modules when asking for
> help upstream. Thanks.
Sorry, I didn't remove it during this log, but I did remove this
module at runtime during my actual sanity tests.
>
> > root@ltts-imx6solo:~# [ 165.208656] sja1105 spi1.0 ethphy0: Link is
> > Up - 100Mbps/Full - flow control off
> > [ 165.225788] sja1105 spi1.0 ethphy1: Link is Up - 100Mbps/Full -
> > flow control off
> > [ 165.235925] IPv6: ADDRCONF(NETDEV_CHANGE): ethphy0: link becomes ready
> > [ 165.255777] IPv6: ADDRCONF(NETDEV_CHANGE): ethphy1: link becomes ready
> >
> > root@ltts-imx6solo:~# ifconfig
> > eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1504
> > inet6 fe80::68fb:8ff:fedf:d377 prefixlen 64 scopeid 0x20<link>
> > ether 6a:fb:08:df:d3:77 txqueuelen 1000 (Ethernet)
> > RX packets 0 bytes 0 (0.0 B)
> > RX errors 0 dropped 0 overruns 0 frame 0
> > TX packets 0 bytes 0 (0.0 B)
> > TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
> >
> > ethphy0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
> > inet 169.254.178.1 netmask 255.255.0.0 broadcast 0.0.0.0
> > inet6 fe80::211:22ff:fe33:4455 prefixlen 64 scopeid 0x20<link>
> > ether 00:11:22:33:44:55 txqueuelen 1000 (Ethernet)
> > RX packets 0 bytes 0 (0.0 B)
> > RX errors 0 dropped 0 overruns 0 frame 0
> > TX packets 30 bytes 4071 (3.9 KiB)
> > TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
> >
> > ethphy1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
> > inet 169.253.178.2 netmask 255.255.0.0 broadcast 0.0.0.0
> > inet6 fe80::211:22ff:fe33:4466 prefixlen 64 scopeid 0x20<link>
> > ether 00:11:22:33:44:66 txqueuelen 1000 (Ethernet)
> > RX packets 0 bytes 0 (0.0 B)
> > RX errors 0 dropped 0 overruns 0 frame 0
> > TX packets 30 bytes 4071 (3.9 KiB)
> > TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
> >
> > lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
> > inet 127.0.0.1 netmask 255.0.0.0
> > inet6 ::1 prefixlen 128 scopeid 0x10<host>
> > loop txqueuelen 1000 (Local Loopback)
> > RX packets 89 bytes 7675 (7.4 KiB)
> > RX errors 0 dropped 0 overruns 0 frame 0
> > TX packets 89 bytes 7675 (7.4 KiB)
> > TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
>
> ifconfig reports statistics counters from the /proc/net/dev interface,
> which the sja1105 does not report very well (they don't come from hardware).
> It's best to use "ethtool -S eth0 | grep -v ': 0'" for FEC and SJA1105
> CPU port (named "p04_*") counters, and "ethtool -S ethphy0 | grep -v ': 0'"
> to get hardware counters from the switch user ports.
Okay.
>
> You can also use the RX counters to determine which switch port is which
> (but the phy-handle of each port to each PHY needs to be correct).
RX counters in ethtool you mean?
>
> > mytsl02383@MYTSL02383:~$ ifconfig -a
> > enp43s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
> > inet 169.254.178.2 netmask 255.255.0.0 broadcast 169.254.255.255
> > inet6 fe80::d71b:4bdd:27bd:2a1a prefixlen 64 scopeid 0x20<link>
> > ether 00:be:43:20:9a:26 txqueuelen 1000 (Ethernet)
> > RX packets 272356 bytes 27099064 (27.0 MB)
> > RX errors 0 dropped 19 overruns 0 frame 0
> > TX packets 862 bytes 300806 (300.8 KB)
> > TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
> > mytsl02383@MYTSL02383:~$ ping 169.254.178.1
> > PING 169.254.178.1 (169.254.178.1) 56(84) bytes of data.
> > From 169.254.178.2 icmp_seq=1 Destination Host Unreachable
> >
> > Let me know if you need any more details.
>
> I'm not convinced packets are routed through ethphy0 or ethphy1, since
> all interfaces have IPv4 link-local addresses only. You can use
> "ip route get 169.254.178.1" to confirm what interface gets chosen.
> This is not indicative of a device-level problem, just a setup one.
> Please set up some IPv4 static addresses which are not link-local on the
> DSA user ports and try to ping a link partner which has an IP address in
> the same subnet.
Okay. I will update this test along with DT changes.
Thanks,
Jagan.
> > If you are truly using MII, then you should remove the RGMII delay
> > properties, and since you are using a 6.1 kernel - hence after kernel
> > commit 5d645df99ac6 ("net: dsa: sja1105: determine PHY/MAC role from PHY
> > interface type") - you should be using phy-mode = "rev-mii" to put this
> > port in MII PHY ("RevMII") mode - to interoperate with the FEC in MII
> > MAC mode.
>
> Okay, I will remove RGMII delay. is phy-mode = "rev-mii" applicable to
> all ports or only for fec port4?
phy-mode indicates what the PHY should be doing. In this case, the
switch is taking the place of the PHY and so the switch MAC needs to
be revMII so that it acts like a PHY. For the other ports of the
switch, you have a real PHY connected, so you want MII.
Andrew
On Sat, Dec 30, 2023 at 01:48:38AM +0530, Jagan Teki wrote:
> On Fri, Dec 29, 2023 at 8:55 PM Vladimir Oltean <[email protected]> wrote:
> > Why all these combinations? You don't know which switch port is which?
>
> This is where I get confused in the first place. I didn't find proper
> information on binding about how the physical pin-out is to be
> configured in DT ports or maybe I didn't understand properly.
>
> As per schematics.
> Pin MII0_RXD0-D3/TXD0-D3 is connected to PROC_MII0_RXD0-D3/TXD0-D3
> this would be fec0.
> Pin MII1_RXD0-D3/TXD0-D3 is connected to PHY_MII1_RXD0-D3/TXD0-D3 this
> would be ethphy0.
> Pin MII2_RXD0-D3/TXD0-D3 is connected to PHY_MII2_RXD0-D3/TXD0-D3 this
> would be ethphy1.
> Pin MII3_RXD0-D3/TXD0-D3 is grounded
> Pin MII4_RXD0-D3/TXD0-D3 is grounded
>
> So, I did use the above 3 combinations and assumed fec0 is always a
> port4 based on existing DTS in the tree. Please let me know which
> configuration is proper as per schematic connections.
With this switch, any port can be a CPU port. The CPU port selection
from existing, unrelated upstream boards has no influence upon yours.
The pin naming in "MII0_RXD/TXD" follows the same numbering scheme as
"port@0" etc. The SJA1105PQRS.pdf datasheet should tell you as much.
So your CPU port should be the "port@0" node and not "port@4". The
switch "port@3" and "port@4" sound like they should be the ones with
status = "disabled".
> > If you are truly using MII, then you should remove the RGMII delay
> > properties, and since you are using a 6.1 kernel - hence after kernel
> > commit 5d645df99ac6 ("net: dsa: sja1105: determine PHY/MAC role from PHY
> > interface type") - you should be using phy-mode = "rev-mii" to put this
> > port in MII PHY ("RevMII") mode - to interoperate with the FEC in MII
> > MAC mode.
>
> Okay, I will remove RGMII delay. is phy-mode = "rev-mii" applicable to
> all ports or only for fec port4?
Use phy-mode = "rev-mii" for the switch port going to the FEC, and
phy-mode = "mii" for the switch ports going to MII PHYs (and for the FEC
itself).
> > You can also use the RX counters to determine which switch port is which
> > (but the phy-handle of each port to each PHY needs to be correct).
>
> RX counters in ethtool you mean?
Yes.