The following series includes some fixes and improvements around RS485 in
the serial core and UART drivers:
Patch 1: serial: Do not hold the port lock when setting rx-during-tx GPIO
Patch 2: serial: core: set missing supported flag for RX during TX GPIO
Patch 3: serial: core: fix sanitizing check for RTS settings
Patch 4: serial: core: make sure RS485 cannot be enabled when it is not
supported
Patch 5: serial: core, imx: do not set RS485 enabled if it is not supported
Patch 6: serial: omap: do not override settings for RS485 support
Patch 7: serial: 8250_exar: Set missing rs485_supported flag
Changes in v8:
- remove wrong setting of SER_RS485_RX_DURING_TX introduced with patch
version 7 (pointed out by Ilpo)
- fix commit message as pointed out by Ilpo
Changes in v7:
- fix errorneous condition in stm32 driver for setting the
SER_RS485_RX_DURING_TX flag (pointed out by Maarten)
- fix compilation issue spotted by kernel test robot
Changes in v6:
- restore RS485 GPIO settings if setting rs485 configuration fails
(pointed out by Ilpo)
- drop change for uart_get_rs485_config()
- rephrase and correct commit messages (pointed out by Ilpo)
- remove unnecessary structure nullification (suggested by Ilpo)
- move all RS485 tasks into one function (suggested by Ilpo)
Changes in v5:
- do not combine the functions that set the RS484 GPIOs (as Hugo originally
suggested)
Changes in v4:
- add comment for function uart_set_rs485_gpios after hint from Hugo
- correct commit message as pointed out by Hugo
- rephrase commit messages
- add patch 7 after discussion with Ilpo
Changes in v3
- Drop patch "Get rid of useless wrapper pl011_get_rs485_mode()" as
requested by Greg
Changes in v2:
- add missing 'Fixes' tags as requested by Greg
- corrected a typo as pointed out by Hugo
- fix issue in imx driver in the serial core as suggested by Uwe
- partly rephrase some commit messages
- add patch 7
Lino Sanfilippo (7):
serial: Do not hold the port lock when setting rx-during-tx GPIO
serial: core: set missing supported flag for RX during TX GPIO
serial: core: fix sanitizing check for RTS settings
serial: core: make sure RS485 cannot be enabled when it is not
supported
serial: core, imx: do not set RS485 enabled if it is not supported
serial: omap: do not override settings for RS485 support
serial: 8250_exar: Set missing rs485_supported flag
drivers/tty/serial/8250/8250_exar.c | 5 ++-
drivers/tty/serial/imx.c | 11 ------
drivers/tty/serial/omap-serial.c | 27 +++++++------
drivers/tty/serial/serial_core.c | 61 +++++++++++++++++++++++------
drivers/tty/serial/stm32-usart.c | 5 +--
5 files changed, 66 insertions(+), 43 deletions(-)
base-commit: 610a9b8f49fbcf1100716370d3b5f6f884a2835a
--
2.43.0
Both the imx and stm32 driver set the rx-during-tx GPIO in rs485_config().
Since this function is called with the port lock held, this can be an
problem in case that setting the GPIO line can sleep (e.g. if a GPIO
expander is used which is connected via SPI or I2C).
Avoid this issue by moving the GPIO setting outside of the port lock into
the serial core and thus making it a generic feature.
Also reset old GPIO settings in case that changing the RS485 configuration
failed.
Fixes: c54d48543689 ("serial: stm32: Add support for rs485 RX_DURING_TX output GPIO")
Fixes: ca530cfa968c ("serial: imx: Add support for RS485 RX_DURING_TX output GPIO")
Cc: Shawn Guo <[email protected]>
Cc: Sascha Hauer <[email protected]>
Cc: [email protected]
Signed-off-by: Lino Sanfilippo <[email protected]>
---
drivers/tty/serial/imx.c | 4 ----
drivers/tty/serial/serial_core.c | 26 ++++++++++++++++++++++++--
drivers/tty/serial/stm32-usart.c | 5 +----
3 files changed, 25 insertions(+), 10 deletions(-)
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 708b9852a575..9cffeb23112b 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -1943,10 +1943,6 @@ static int imx_uart_rs485_config(struct uart_port *port, struct ktermios *termio
rs485conf->flags & SER_RS485_RX_DURING_TX)
imx_uart_start_rx(port);
- if (port->rs485_rx_during_tx_gpio)
- gpiod_set_value_cansleep(port->rs485_rx_during_tx_gpio,
- !!(rs485conf->flags & SER_RS485_RX_DURING_TX));
-
return 0;
}
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index f1348a509552..d155131f221d 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -1402,6 +1402,16 @@ static void uart_set_rs485_termination(struct uart_port *port,
!!(rs485->flags & SER_RS485_TERMINATE_BUS));
}
+static void uart_set_rs485_rx_during_tx(struct uart_port *port,
+ const struct serial_rs485 *rs485)
+{
+ if (!(rs485->flags & SER_RS485_ENABLED))
+ return;
+
+ gpiod_set_value_cansleep(port->rs485_rx_during_tx_gpio,
+ !!(rs485->flags & SER_RS485_RX_DURING_TX));
+}
+
static int uart_rs485_config(struct uart_port *port)
{
struct serial_rs485 *rs485 = &port->rs485;
@@ -1413,12 +1423,17 @@ static int uart_rs485_config(struct uart_port *port)
uart_sanitize_serial_rs485(port, rs485);
uart_set_rs485_termination(port, rs485);
+ uart_set_rs485_rx_during_tx(port, rs485);
uart_port_lock_irqsave(port, &flags);
ret = port->rs485_config(port, NULL, rs485);
uart_port_unlock_irqrestore(port, flags);
- if (ret)
+ if (ret) {
memset(rs485, 0, sizeof(*rs485));
+ /* unset GPIOs */
+ gpiod_set_value_cansleep(port->rs485_term_gpio, 0);
+ gpiod_set_value_cansleep(port->rs485_rx_during_tx_gpio, 0);
+ }
return ret;
}
@@ -1457,6 +1472,7 @@ static int uart_set_rs485_config(struct tty_struct *tty, struct uart_port *port,
return ret;
uart_sanitize_serial_rs485(port, &rs485);
uart_set_rs485_termination(port, &rs485);
+ uart_set_rs485_rx_during_tx(port, &rs485);
uart_port_lock_irqsave(port, &flags);
ret = port->rs485_config(port, &tty->termios, &rs485);
@@ -1468,8 +1484,14 @@ static int uart_set_rs485_config(struct tty_struct *tty, struct uart_port *port,
port->ops->set_mctrl(port, port->mctrl);
}
uart_port_unlock_irqrestore(port, flags);
- if (ret)
+ if (ret) {
+ /* restore old GPIO settings */
+ gpiod_set_value_cansleep(port->rs485_term_gpio,
+ !!(port->rs485.flags & SER_RS485_TERMINATE_BUS));
+ gpiod_set_value_cansleep(port->rs485_rx_during_tx_gpio,
+ !!(port->rs485.flags & SER_RS485_RX_DURING_TX));
return ret;
+ }
if (copy_to_user(rs485_user, &port->rs485, sizeof(port->rs485)))
return -EFAULT;
diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index 3048620315d6..ec9a72a5bea9 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -226,10 +226,7 @@ static int stm32_usart_config_rs485(struct uart_port *port, struct ktermios *ter
stm32_usart_clr_bits(port, ofs->cr1, BIT(cfg->uart_enable_bit));
- if (port->rs485_rx_during_tx_gpio)
- gpiod_set_value_cansleep(port->rs485_rx_during_tx_gpio,
- !!(rs485conf->flags & SER_RS485_RX_DURING_TX));
- else
+ if (!port->rs485_rx_during_tx_gpio)
rs485conf->flags |= SER_RS485_RX_DURING_TX;
if (rs485conf->flags & SER_RS485_ENABLED) {
--
2.43.0
If the RS485 feature RX-during-TX is supported by means of a GPIO set the
according supported flag. Otherwise setting this feature from userspace may
not be possible, since in uart_sanitize_serial_rs485() the passed RS485
configuration is matched against the supported features and unsupported
settings are thereby removed and thus take no effect.
Cc: [email protected]
Fixes: 163f080eb717 ("serial: core: Add option to output RS485 RX_DURING_TX state via GPIO")
Reviewed-by: Ilpo Järvinen <[email protected]>
Signed-off-by: Lino Sanfilippo <[email protected]>
---
drivers/tty/serial/serial_core.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index d155131f221d..1204102d7162 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -3642,6 +3642,8 @@ int uart_get_rs485_mode(struct uart_port *port)
if (IS_ERR(desc))
return dev_err_probe(dev, PTR_ERR(desc), "Cannot get rs485-rx-during-tx-gpios\n");
port->rs485_rx_during_tx_gpio = desc;
+ if (port->rs485_rx_during_tx_gpio)
+ port->rs485_supported.flags |= SER_RS485_RX_DURING_TX;
return 0;
}
--
2.43.0
Among other things uart_sanitize_serial_rs485() tests the sanity of the RTS
settings in a RS485 configuration that has been passed by userspace.
If RTS-on-send and RTS-after-send are both set or unset the configuration
is adjusted and RTS-after-send is disabled and RTS-on-send enabled.
This however makes only sense if both RTS modes are actually supported by
the driver.
With commit be2e2cb1d281 ("serial: Sanitize rs485_struct") the code does
take the driver support into account but only checks if one of both RTS
modes are supported. This may lead to the errorneous result of RTS-on-send
being set even if only RTS-after-send is supported.
Fix this by changing the implemented logic: First clear all unsupported
flags in the RS485 configuration, then adjust an invalid RTS setting by
taking into account which RTS mode is supported.
Cc: [email protected]
Fixes: be2e2cb1d281 ("serial: Sanitize rs485_struct")
Reviewed-by: Ilpo Järvinen <[email protected]>
Signed-off-by: Lino Sanfilippo <[email protected]>
---
drivers/tty/serial/serial_core.c | 28 ++++++++++++++++++----------
1 file changed, 18 insertions(+), 10 deletions(-)
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index 1204102d7162..f67fb6a04983 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -1371,19 +1371,27 @@ static void uart_sanitize_serial_rs485(struct uart_port *port, struct serial_rs4
return;
}
+ rs485->flags &= supported_flags;
+
/* Pick sane settings if the user hasn't */
- if ((supported_flags & (SER_RS485_RTS_ON_SEND|SER_RS485_RTS_AFTER_SEND)) &&
- !(rs485->flags & SER_RS485_RTS_ON_SEND) ==
+ if (!(rs485->flags & SER_RS485_RTS_ON_SEND) ==
!(rs485->flags & SER_RS485_RTS_AFTER_SEND)) {
- dev_warn_ratelimited(port->dev,
- "%s (%d): invalid RTS setting, using RTS_ON_SEND instead\n",
- port->name, port->line);
- rs485->flags |= SER_RS485_RTS_ON_SEND;
- rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
- supported_flags |= SER_RS485_RTS_ON_SEND|SER_RS485_RTS_AFTER_SEND;
- }
+ if (supported_flags & SER_RS485_RTS_ON_SEND) {
+ rs485->flags |= SER_RS485_RTS_ON_SEND;
+ rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
- rs485->flags &= supported_flags;
+ dev_warn_ratelimited(port->dev,
+ "%s (%d): invalid RTS setting, using RTS_ON_SEND instead\n",
+ port->name, port->line);
+ } else {
+ rs485->flags |= SER_RS485_RTS_AFTER_SEND;
+ rs485->flags &= ~SER_RS485_RTS_ON_SEND;
+
+ dev_warn_ratelimited(port->dev,
+ "%s (%d): invalid RTS setting, using RTS_AFTER_SEND instead\n",
+ port->name, port->line);
+ }
+ }
uart_sanitize_serial_rs485_delays(port, rs485);
--
2.43.0
The UART supports an auto-RTS mode in which the RTS pin is automatically
activated during transmission. So mark this mode as being supported even
if RTS is not controlled by the driver but the UART.
Also the serial core expects now at least one of both modes rts-on-send or
rts-after-send to be supported. This is since during sanitization
unsupported flags are deleted from a RS485 configuration set by userspace.
However if the configuration ends up with both flags unset, the core prints
a warning since it considers such a configuration invalid (see
uart_sanitize_serial_rs485()).
Cc: [email protected]
Reviewed-by: Ilpo Järvinen <[email protected]>
Signed-off-by: Lino Sanfilippo <[email protected]>
---
drivers/tty/serial/8250/8250_exar.c | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
index 6085d356ad86..23366f868ae3 100644
--- a/drivers/tty/serial/8250/8250_exar.c
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -480,7 +480,7 @@ static int sealevel_rs485_config(struct uart_port *port, struct ktermios *termio
}
static const struct serial_rs485 generic_rs485_supported = {
- .flags = SER_RS485_ENABLED,
+ .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND,
};
static const struct exar8250_platform exar8250_default_platform = {
@@ -524,7 +524,8 @@ static int iot2040_rs485_config(struct uart_port *port, struct ktermios *termios
}
static const struct serial_rs485 iot2040_rs485_supported = {
- .flags = SER_RS485_ENABLED | SER_RS485_RX_DURING_TX | SER_RS485_TERMINATE_BUS,
+ .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
+ SER_RS485_RX_DURING_TX | SER_RS485_TERMINATE_BUS,
};
static const struct property_entry iot2040_gpio_properties[] = {
--
2.43.0
Some uart drivers specify a rs485_config() function and then decide later
to disable RS485 support for some reason (e.g. imx and ar933).
In these cases userspace may be able to activate RS485 via TIOCSRS485
nevertheless, since in uart_set_rs485_config() an existing rs485_config()
function indicates that RS485 is supported.
Make sure that this is not longer possible by checking the uarts
rs485_supported.flags instead and bailing out if SER_RS485_ENABLED is not
set.
Furthermore instead of returning an empty structure return -ENOTTY if the
RS485 configuration is requested via TIOCGRS485 but RS485 is not supported.
This has a small impact on userspace visibility but it is consistent with
the -ENOTTY error for TIOCGRS485.
Fixes: e849145e1fdd ("serial: ar933x: Fill in rs485_supported")
Fixes: 55e18c6b6d42 ("serial: imx: Remove serial_rs485 sanitization")
Cc: Shawn Guo <[email protected]>
Cc: Sascha Hauer <[email protected]>
Cc: [email protected]
Reviewed-by: Ilpo Järvinen <[email protected]>
Signed-off-by: Lino Sanfilippo <[email protected]>
---
drivers/tty/serial/serial_core.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index f67fb6a04983..28bcbc686c67 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -1469,7 +1469,7 @@ static int uart_set_rs485_config(struct tty_struct *tty, struct uart_port *port,
int ret;
unsigned long flags;
- if (!port->rs485_config)
+ if (!(port->rs485_supported.flags & SER_RS485_ENABLED))
return -ENOTTY;
if (copy_from_user(&rs485, rs485_user, sizeof(*rs485_user)))
--
2.43.0
The drivers RS485 support is deactivated if there is no RTS GPIO available.
This is done by nullifying the ports rs485_supported struct. After that
however the settings in serial_omap_rs485_supported are assigned to the
same structure unconditionally, which results in an unintended reactivation
of RS485 support.
Fix this by moving the assignment to the beginning of
serial_omap_probe_rs485() and thus before the check for the RTS GPIO.
Also relocate the assignment of serial_omap_config_rs485() to have the
complete RS485 setup in one function.
Fixes: e2752ae3cfc9 ("serial: omap: Disallow RS-485 if rts-gpio is not specified")
Cc: [email protected]
Reviewed-by: Ilpo Järvinen <[email protected]>
Signed-off-by: Lino Sanfilippo <[email protected]>
---
drivers/tty/serial/omap-serial.c | 27 ++++++++++++++-------------
1 file changed, 14 insertions(+), 13 deletions(-)
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index ad4c1c5d0a7f..f4c6ff806465 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -1483,6 +1483,13 @@ static struct omap_uart_port_info *of_get_uart_port_info(struct device *dev)
return omap_up_info;
}
+static const struct serial_rs485 serial_omap_rs485_supported = {
+ .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND |
+ SER_RS485_RX_DURING_TX,
+ .delay_rts_before_send = 1,
+ .delay_rts_after_send = 1,
+};
+
static int serial_omap_probe_rs485(struct uart_omap_port *up,
struct device *dev)
{
@@ -1497,6 +1504,9 @@ static int serial_omap_probe_rs485(struct uart_omap_port *up,
if (!np)
return 0;
+ up->port.rs485_config = serial_omap_config_rs485;
+ up->port.rs485_supported = serial_omap_rs485_supported;
+
ret = uart_get_rs485_mode(&up->port);
if (ret)
return ret;
@@ -1531,13 +1541,6 @@ static int serial_omap_probe_rs485(struct uart_omap_port *up,
return 0;
}
-static const struct serial_rs485 serial_omap_rs485_supported = {
- .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND |
- SER_RS485_RX_DURING_TX,
- .delay_rts_before_send = 1,
- .delay_rts_after_send = 1,
-};
-
static int serial_omap_probe(struct platform_device *pdev)
{
struct omap_uart_port_info *omap_up_info = dev_get_platdata(&pdev->dev);
@@ -1604,17 +1607,11 @@ static int serial_omap_probe(struct platform_device *pdev)
dev_info(up->port.dev, "no wakeirq for uart%d\n",
up->port.line);
- ret = serial_omap_probe_rs485(up, &pdev->dev);
- if (ret < 0)
- goto err_rs485;
-
sprintf(up->name, "OMAP UART%d", up->port.line);
up->port.mapbase = mem->start;
up->port.membase = base;
up->port.flags = omap_up_info->flags;
up->port.uartclk = omap_up_info->uartclk;
- up->port.rs485_config = serial_omap_config_rs485;
- up->port.rs485_supported = serial_omap_rs485_supported;
if (!up->port.uartclk) {
up->port.uartclk = DEFAULT_CLK_SPEED;
dev_warn(&pdev->dev,
@@ -1622,6 +1619,10 @@ static int serial_omap_probe(struct platform_device *pdev)
DEFAULT_CLK_SPEED);
}
+ ret = serial_omap_probe_rs485(up, &pdev->dev);
+ if (ret < 0)
+ goto err_rs485;
+
up->latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE;
up->calc_latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE;
cpu_latency_qos_add_request(&up->pm_qos_request, up->latency);
--
2.43.0
If the imx driver cannot support RS485 it nullifies the ports
rs485_supported structure. But it still calls uart_get_rs485_mode() which
may set the RS485_ENABLED flag nevertheless.
This may lead to an attempt to configure RS485 even if it is not supported
when the flag is evaluated in uart_configure_port() at port startup.
Avoid this by bailing out of uart_get_rs485_mode() if the RS485_ENABLED
flag is not supported by the caller.
With this fix a check for RTS availability is now obsolete in the imx
driver, since it can not evaluate to true any more. So remove this check.
Furthermore the explicit nullifcation of rs485_supported is not needed,
since the memory has already been set to zeros at allocation. So remove
this, too.
Fixes: 00d7a00e2a6f ("serial: imx: Fill in rs485_supported")
Cc: Shawn Guo <[email protected]>
Cc: Sascha Hauer <[email protected]>
Cc: [email protected]
Reviewed-by: Ilpo Järvinen <[email protected]>
Suggested-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Lino Sanfilippo <[email protected]>
---
drivers/tty/serial/imx.c | 7 -------
drivers/tty/serial/serial_core.c | 3 +++
2 files changed, 3 insertions(+), 7 deletions(-)
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 9cffeb23112b..198ce7e7bc8b 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -2206,7 +2206,6 @@ static enum hrtimer_restart imx_trigger_stop_tx(struct hrtimer *t)
return HRTIMER_NORESTART;
}
-static const struct serial_rs485 imx_no_rs485 = {}; /* No RS485 if no RTS */
static const struct serial_rs485 imx_rs485_supported = {
.flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND |
SER_RS485_RX_DURING_TX,
@@ -2290,8 +2289,6 @@ static int imx_uart_probe(struct platform_device *pdev)
/* RTS is required to control the RS485 transmitter */
if (sport->have_rtscts || sport->have_rtsgpio)
sport->port.rs485_supported = imx_rs485_supported;
- else
- sport->port.rs485_supported = imx_no_rs485;
sport->port.flags = UPF_BOOT_AUTOCONF;
timer_setup(&sport->timer, imx_uart_timeout, 0);
@@ -2328,10 +2325,6 @@ static int imx_uart_probe(struct platform_device *pdev)
return ret;
}
- if (sport->port.rs485.flags & SER_RS485_ENABLED &&
- (!sport->have_rtscts && !sport->have_rtsgpio))
- dev_err(&pdev->dev, "no RTS control, disabling rs485\n");
-
/*
* If using the i.MX UART RTS/CTS control then the RTS (CTS_B)
* signal cannot be set low during transmission in case the
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index 28bcbc686c67..93e4e1693601 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -3600,6 +3600,9 @@ int uart_get_rs485_mode(struct uart_port *port)
u32 rs485_delay[2];
int ret;
+ if (!(port->rs485_supported.flags & SER_RS485_ENABLED))
+ return 0;
+
ret = device_property_read_u32_array(dev, "rs485-rts-delay",
rs485_delay, 2);
if (!ret) {
--
2.43.0
On Fri, Jan 05, 2024 at 03:11:46PM +0100, Lino Sanfilippo wrote:
> The following series includes some fixes and improvements around RS485 in
> the serial core and UART drivers:
>
> Patch 1: serial: Do not hold the port lock when setting rx-during-tx GPIO
> Patch 2: serial: core: set missing supported flag for RX during TX GPIO
> Patch 3: serial: core: fix sanitizing check for RTS settings
> Patch 4: serial: core: make sure RS485 cannot be enabled when it is not
> supported
> Patch 5: serial: core, imx: do not set RS485 enabled if it is not supported
> Patch 6: serial: omap: do not override settings for RS485 support
> Patch 7: serial: 8250_exar: Set missing rs485_supported flag
>
> Changes in v8:
> - remove wrong setting of SER_RS485_RX_DURING_TX introduced with patch
> version 7 (pointed out by Ilpo)
> - fix commit message as pointed out by Ilpo
Aren't these already in the tree? None of them apply, what am I doing
wrong?
confused,
greg k-h
Hi,
On 28.01.24 04:10, Greg KH wrote:
> ATTENTION: This e-mail is from an external sender. Please check attachments and links before opening e.g. with mouseover.
>
>
> On Fri, Jan 05, 2024 at 03:11:46PM +0100, Lino Sanfilippo wrote:
>> The following series includes some fixes and improvements around RS485 in
>> the serial core and UART drivers:
>>
>> Patch 1: serial: Do not hold the port lock when setting rx-during-tx GPIO
>> Patch 2: serial: core: set missing supported flag for RX during TX GPIO
>> Patch 3: serial: core: fix sanitizing check for RTS settings
>> Patch 4: serial: core: make sure RS485 cannot be enabled when it is not
>> supported
>> Patch 5: serial: core, imx: do not set RS485 enabled if it is not supported
>> Patch 6: serial: omap: do not override settings for RS485 support
>> Patch 7: serial: 8250_exar: Set missing rs485_supported flag
>>
>> Changes in v8:
>> - remove wrong setting of SER_RS485_RX_DURING_TX introduced with patch
>> version 7 (pointed out by Ilpo)
>> - fix commit message as pointed out by Ilpo
>
> Aren't these already in the tree? None of them apply, what am I doing
> wrong?
>
> confused,
>
> greg k-h
Right, the series is already applied. However patch 1 -
07c30ea5861f (" serial: Do not hold the port lock when setting rx-during-tx GPIO") -
still contains a flaw which is why I sent a v8 to correct that. I sent it a bit too late
obviously, sorry for that.
You can ignore series v8 and instead I can send a follow up patch that corrects the flaw.
Again, sorry for the confusion.
Regards,
Lino