From: Frieder Schrempf <[email protected]>
This series adds upstream support for the Sielaff i.MX6 Solo board.
It is used as controller and user interface in vending machines. It
is based on the i.MX6 Solo SoC and features the following
peripherals and interfaces:
* 512 MB DDR3 RAM
* 512 MB NAND Flash
* 1 MB NOR Flash
* SD card
* Debug LED
* Debug UART
* Key Inputs
* RTC
* RS232
* 100 MBit Ethernet
* USB Hub
* USB OTG
* HDMI
* 7" LVDS IPS panel
* PWM Backlight
* Optional Extension Board with USB Ethernet NIC
Patch 1 adds the vendor prefix, patch 2 adds the DT bindings and
patch 3 adds the DT.
Changes in v2:
* Add Acked-by from Conor (Thanks!)
* Fix touchscreen node names (Thanks Fabio!)
Frieder Schrempf (3):
dt-bindings: vendor-prefixes: Add Sielaff
dt-bindings: arm: fsl: Add Sielaff i.MX6 Solo board
ARM: dts: imx6dl: Add support for Sielaff i.MX6 Solo board
.../devicetree/bindings/arm/fsl.yaml | 1 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
arch/arm/boot/dts/nxp/imx/Makefile | 1 +
arch/arm/boot/dts/nxp/imx/imx6dl-sielaff.dts | 533 ++++++++++++++++++
4 files changed, 537 insertions(+)
create mode 100644 arch/arm/boot/dts/nxp/imx/imx6dl-sielaff.dts
--
2.43.0
From: Frieder Schrempf <[email protected]>
Add "Sielaff GmbH & Co. KG Automatenbau Herrieden" (https://sielaff.de).
Signed-off-by: Frieder Schrempf <[email protected]>
Acked-by: Conor Dooley <[email protected]>
---
Changes in v2:
* Add Acked-by from Conor (Thanks!)
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 309b94c328c84..8825a9f60ac5a 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1233,6 +1233,8 @@ patternProperties:
description: Si-En Technology Ltd.
"^si-linux,.*":
description: Silicon Linux Corporation
+ "^sielaff,.*":
+ description: Sielaff GmbH & Co. KG Automatenbau Herrieden
"^siemens,.*":
description: Siemens AG
"^sifive,.*":
--
2.43.0
From: Frieder Schrempf <[email protected]>
Add compatible for the Sielaff i.MX6 Solo board.
Signed-off-by: Frieder Schrempf <[email protected]>
Acked-by: Conor Dooley <[email protected]>
---
Changes in v2:
* Add Acked-by from Conor (Thanks!)
---
Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 32b195852a75c..f6cdf4a8e51a2 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -469,6 +469,7 @@ properties:
- prt,prtvt7 # Protonic VT7 board
- rex,imx6dl-rex-basic # Rex Basic i.MX6 Dual Lite Board
- riot,imx6s-riotboard # RIoTboard i.MX6S
+ - sielaff,imx6dl-board # Sielaff i.MX6 Solo Board
- skov,imx6dl-skov-revc-lt2 # SKOV IMX6 CPU SoloCore lt2
- skov,imx6dl-skov-revc-lt6 # SKOV IMX6 CPU SoloCore lt6
- solidrun,cubox-i/dl # SolidRun Cubox-i Solo/DualLite
--
2.43.0
From: Frieder Schrempf <[email protected]>
The Sielaff i.MX6 Solo board is used as controller and user interface
in vending machines. It is based on the i.MX6 Solo SoC and features
the following peripherals and interfaces:
* 512 MB DDR3 RAM
* 512 MB NAND Flash
* 1 MB NOR Flash
* SD card
* Debug LED
* Debug UART
* Key Inputs
* RTC
* RS232
* 100 MBit Ethernet
* USB Hub
* USB OTG
* HDMI
* 7" LVDS IPS panel
* PWM Backlight
* Optional Extension Board with USB Ethernet NIC
Signed-off-by: Frieder Schrempf <[email protected]>
---
Changes in v2:
* Fix touchscreen node names (Thanks Fabio!)
---
arch/arm/boot/dts/nxp/imx/Makefile | 1 +
arch/arm/boot/dts/nxp/imx/imx6dl-sielaff.dts | 533 +++++++++++++++++++
2 files changed, 534 insertions(+)
create mode 100644 arch/arm/boot/dts/nxp/imx/imx6dl-sielaff.dts
diff --git a/arch/arm/boot/dts/nxp/imx/Makefile b/arch/arm/boot/dts/nxp/imx/Makefile
index a724d1a7a9a07..c32e004e7610c 100644
--- a/arch/arm/boot/dts/nxp/imx/Makefile
+++ b/arch/arm/boot/dts/nxp/imx/Makefile
@@ -118,6 +118,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-sabrelite.dtb \
imx6dl-sabresd.dtb \
imx6dl-savageboard.dtb \
+ imx6dl-sielaff.dtb \
imx6dl-skov-revc-lt2.dtb \
imx6dl-skov-revc-lt6.dtb \
imx6dl-solidsense.dtb \
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-sielaff.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-sielaff.dts
new file mode 100644
index 0000000000000..7de8d5f265187
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-sielaff.dts
@@ -0,0 +1,533 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2022 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Sielaff i.MX6 Solo";
+ compatible = "sielaff,imx6dl-board", "fsl,imx6dl";
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ backlight: pwm-backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ pwms = <&pwm3 0 50000 0>;
+ brightness-levels = <0 0 64 88 112 136 184 232 255>;
+ default-brightness-level = <4>;
+ enable-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+ power-supply = <®_backlight>;
+ };
+
+ cec {
+ compatible = "cec-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hdmi_cec>;
+ cec-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
+ hdmi-phandle = <&hdmi>;
+ };
+
+ enet_ref: clock-enet-ref {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <50000000>;
+ clock-output-names = "enet-ref";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ key-0 {
+ gpios = <&gpio2 16 0>;
+ debounce-interval = <10>;
+ linux,code = <1>;
+ };
+
+ key-1 {
+ gpios = <&gpio3 27 0>;
+ debounce-interval = <10>;
+ linux,code = <2>;
+ };
+
+ key-2 {
+ gpios = <&gpio5 4 0>;
+ debounce-interval = <10>;
+ linux,code = <3>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+
+ led-debug {
+ label = "debug-led";
+ gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ memory@80000000 {
+ reg = <0x80000000 0x20000000>;
+ device_type = "memory";
+ };
+
+ osc_eth_phy: clock-osc-eth-phy {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ clock-output-names = "osc-eth-phy";
+ };
+
+ panel {
+ compatible = "lg,lb070wv8";
+ backlight = <&backlight>;
+ power-supply = <®_3v3>;
+
+ port {
+ panel_in_lvds: endpoint {
+ remote-endpoint = <&lvds_out>;
+ };
+ };
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_backlight: regulator-backlight {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_backlight>;
+ enable-active-high;
+ gpio = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+ regulator-name = "backlight";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ reg_usb_otg_vbus: regulator-usb-otg-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usbotg_vbus>;
+ enable-active-high;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ cs-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&fec {
+ /*
+ * Set PTP clock to external instead of internal reference, as the
+ * REF_CLK from the PHY is fed back into the i.MX6 and the GPR
+ * register needs to be set accordingly (see mach-imx6q.c).
+ */
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>,
+ <&enet_ref>,
+ <&clks IMX6QDL_CLK_ENET_REF>;
+ clock-names = "ipg", "ahb", "ptp", "enet_out";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-connection-type = "rmii";
+ phy-handle = <ðphy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@1 {
+ reg = <1>;
+ clocks = <&osc_eth_phy>;
+ clock-names = "rmii-ref";
+ micrel,led-mode = <1>;
+ reset-assert-us = <500>;
+ reset-deassert-us = <100>;
+ reset-gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "key-out", "key-in",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "lan9500a-rst", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ status = "okay";
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c4>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ clock-frequency = <100000>;
+ status = "okay";
+
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ clock-frequency = <100000>;
+ status = "okay";
+
+ touchscreen@55 {
+ compatible = "sitronix,st1633";
+ reg = <0x55>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_touch>;
+ interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-parent = <&gpio5>;
+ gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+ status = "disabled";
+ };
+
+ touchscreen@5d {
+ compatible = "goodix,gt928";
+ reg = <0x5d>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_touch>;
+ interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio5>;
+ irq-gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+ status = "disabled";
+ };
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ clock-frequency = <100000>;
+ status = "okay";
+};
+
+&ldb {
+ status = "okay";
+
+ lvds: lvds-channel@0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <24>;
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds_out: endpoint {
+ remote-endpoint = <&panel_in_lvds>;
+ };
+ };
+ };
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&usbh1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1>;
+ disable-over-current;
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb1@1 {
+ compatible = "usb4b4,6570";
+ reg = <1>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+
+ assigned-clocks = <&clks IMX6QDL_CLK_CKO>,
+ <&clks IMX6QDL_CLK_CKO2_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_CKO2>,
+ <&clks IMX6QDL_CLK_OSC>;
+ assigned-clock-rates = <12000000 0>;
+ };
+};
+
+&usbotg {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ dr_mode = "host";
+ over-current-active-low;
+ vbus-supply = <®_usb_otg_vbus>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <®_3v3>;
+ voltage-ranges = <3300 3300>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RD0__GPIO6_IO25 0x1b0b0 /* PMIC_IRQ */
+ MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0
+ MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
+ MX6QDL_PAD_SD2_DAT0__GPIO1_IO15 0x1b0b0
+ MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0
+ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b0
+ >;
+ };
+
+ pinctrl_backlight: backlightgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29 0x100b1
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b1
+ >;
+ };
+
+ pinctrl_gpio_keys: gpiokeysgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x1b080
+ MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x1b080
+ MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x1b080
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ >;
+ };
+
+ pinctrl_hdmi_cec: hdmicecgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A21__GPIO2_IO17 0x1b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001f8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__I2C4_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_8__I2C4_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_reg_backlight: regbacklightgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23 0x1b0b1
+ >;
+ };
+
+ pinctrl_reg_usbotg_vbus: regusbotgvbusgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b1
+ >;
+ };
+
+ pinctrl_touch: touchgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b0
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbh1: usbh1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b1
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x100b1
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__WDOG1_B 0x1b0b0
+ >;
+ };
+};
--
2.43.0
On Tue, Jan 16, 2024 at 07:10:25PM +0100, Frieder Schrempf wrote:
> From: Frieder Schrempf <[email protected]>
>
> This series adds upstream support for the Sielaff i.MX6 Solo board.
> It is used as controller and user interface in vending machines. It
> is based on the i.MX6 Solo SoC and features the following
> peripherals and interfaces:
>
> * 512 MB DDR3 RAM
> * 512 MB NAND Flash
> * 1 MB NOR Flash
> * SD card
> * Debug LED
> * Debug UART
> * Key Inputs
> * RTC
> * RS232
> * 100 MBit Ethernet
> * USB Hub
> * USB OTG
> * HDMI
> * 7" LVDS IPS panel
> * PWM Backlight
> * Optional Extension Board with USB Ethernet NIC
>
> Patch 1 adds the vendor prefix, patch 2 adds the DT bindings and
> patch 3 adds the DT.
>
> Changes in v2:
> * Add Acked-by from Conor (Thanks!)
> * Fix touchscreen node names (Thanks Fabio!)
>
> Frieder Schrempf (3):
> dt-bindings: vendor-prefixes: Add Sielaff
> dt-bindings: arm: fsl: Add Sielaff i.MX6 Solo board
> ARM: dts: imx6dl: Add support for Sielaff i.MX6 Solo board
Applied both, thanks!