From: Nikita Shubin <[email protected]>
- add OF ID match table
- drop platform DMA and filters
- change DMA setup to OF, so we can defer probe
Reviewed-by: Sergey Shtylyov <[email protected]>
Acked-by: Damien Le Moal <[email protected]>
Signed-off-by: Nikita Shubin <[email protected]>
---
drivers/ata/pata_ep93xx.c | 81 +++++++++++++++++++++++++----------------------
1 file changed, 43 insertions(+), 38 deletions(-)
diff --git a/drivers/ata/pata_ep93xx.c b/drivers/ata/pata_ep93xx.c
index c84a20892f1b..2bc446bdea06 100644
--- a/drivers/ata/pata_ep93xx.c
+++ b/drivers/ata/pata_ep93xx.c
@@ -44,8 +44,8 @@
#include <linux/delay.h>
#include <linux/dmaengine.h>
#include <linux/ktime.h>
+#include <linux/mod_devicetable.h>
-#include <linux/platform_data/dma-ep93xx.h>
#include <linux/soc/cirrus/ep93xx.h>
#define DRV_NAME "ep93xx-ide"
@@ -126,7 +126,7 @@ enum {
};
struct ep93xx_pata_data {
- const struct platform_device *pdev;
+ struct platform_device *pdev;
void __iomem *ide_base;
struct ata_timing t;
bool iordy;
@@ -135,9 +135,7 @@ struct ep93xx_pata_data {
unsigned long udma_out_phys;
struct dma_chan *dma_rx_channel;
- struct ep93xx_dma_data dma_rx_data;
struct dma_chan *dma_tx_channel;
- struct ep93xx_dma_data dma_tx_data;
};
static void ep93xx_pata_clear_regs(void __iomem *base)
@@ -637,20 +635,13 @@ static void ep93xx_pata_release_dma(struct ep93xx_pata_data *drv_data)
}
}
-static bool ep93xx_pata_dma_filter(struct dma_chan *chan, void *filter_param)
+static int ep93xx_pata_dma_init(struct ep93xx_pata_data *drv_data)
{
- if (ep93xx_dma_chan_is_m2p(chan))
- return false;
-
- chan->private = filter_param;
- return true;
-}
-
-static void ep93xx_pata_dma_init(struct ep93xx_pata_data *drv_data)
-{
- const struct platform_device *pdev = drv_data->pdev;
+ struct platform_device *pdev = drv_data->pdev;
+ struct device *dev = &pdev->dev;
dma_cap_mask_t mask;
struct dma_slave_config conf;
+ int ret;
dma_cap_zero(mask);
dma_cap_set(DMA_SLAVE, mask);
@@ -660,22 +651,17 @@ static void ep93xx_pata_dma_init(struct ep93xx_pata_data *drv_data)
* to request only one channel, and reprogram it's direction at
* start of new transfer.
*/
- drv_data->dma_rx_data.port = EP93XX_DMA_IDE;
- drv_data->dma_rx_data.direction = DMA_DEV_TO_MEM;
- drv_data->dma_rx_data.name = "ep93xx-pata-rx";
- drv_data->dma_rx_channel = dma_request_channel(mask,
- ep93xx_pata_dma_filter, &drv_data->dma_rx_data);
- if (!drv_data->dma_rx_channel)
- return;
+ drv_data->dma_rx_channel = dma_request_chan(dev, "rx");
+ if (IS_ERR(drv_data->dma_rx_channel)) {
+ ret = PTR_ERR(drv_data->dma_rx_channel);
+ return dev_err_probe(dev, ret, "rx DMA setup failed\n");
+ }
- drv_data->dma_tx_data.port = EP93XX_DMA_IDE;
- drv_data->dma_tx_data.direction = DMA_MEM_TO_DEV;
- drv_data->dma_tx_data.name = "ep93xx-pata-tx";
- drv_data->dma_tx_channel = dma_request_channel(mask,
- ep93xx_pata_dma_filter, &drv_data->dma_tx_data);
- if (!drv_data->dma_tx_channel) {
- dma_release_channel(drv_data->dma_rx_channel);
- return;
+ drv_data->dma_tx_channel = dma_request_chan(&pdev->dev, "tx");
+ if (IS_ERR(drv_data->dma_tx_channel)) {
+ ret = PTR_ERR(drv_data->dma_tx_channel);
+ dev_err_probe(dev, ret, "tx DMA setup failed\n");
+ goto fail_release_rx;
}
/* Configure receive channel direction and source address */
@@ -683,10 +669,10 @@ static void ep93xx_pata_dma_init(struct ep93xx_pata_data *drv_data)
conf.direction = DMA_DEV_TO_MEM;
conf.src_addr = drv_data->udma_in_phys;
conf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- if (dmaengine_slave_config(drv_data->dma_rx_channel, &conf)) {
- dev_err(&pdev->dev, "failed to configure rx dma channel\n");
- ep93xx_pata_release_dma(drv_data);
- return;
+ ret = dmaengine_slave_config(drv_data->dma_rx_channel, &conf);
+ if (ret) {
+ dev_err_probe(dev, ret, "failed to configure rx dma channel");
+ goto fail_release_dma;
}
/* Configure transmit channel direction and destination address */
@@ -694,10 +680,20 @@ static void ep93xx_pata_dma_init(struct ep93xx_pata_data *drv_data)
conf.direction = DMA_MEM_TO_DEV;
conf.dst_addr = drv_data->udma_out_phys;
conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- if (dmaengine_slave_config(drv_data->dma_tx_channel, &conf)) {
- dev_err(&pdev->dev, "failed to configure tx dma channel\n");
- ep93xx_pata_release_dma(drv_data);
+ ret = dmaengine_slave_config(drv_data->dma_tx_channel, &conf);
+ if (ret) {
+ dev_err_probe(dev, ret, "failed to configure tx dma channel");
+ goto fail_release_dma;
}
+
+ return 0;
+
+fail_release_rx:
+ dma_release_channel(drv_data->dma_rx_channel);
+fail_release_dma:
+ ep93xx_pata_release_dma(drv_data);
+
+ return ret;
}
static void ep93xx_pata_dma_start(struct ata_queued_cmd *qc)
@@ -954,7 +950,9 @@ static int ep93xx_pata_probe(struct platform_device *pdev)
drv_data->ide_base = ide_base;
drv_data->udma_in_phys = mem_res->start + IDEUDMADATAIN;
drv_data->udma_out_phys = mem_res->start + IDEUDMADATAOUT;
- ep93xx_pata_dma_init(drv_data);
+ err = ep93xx_pata_dma_init(drv_data);
+ if (err)
+ return err;
/* allocate host */
host = ata_host_alloc(&pdev->dev, 1);
@@ -1021,9 +1019,16 @@ static void ep93xx_pata_remove(struct platform_device *pdev)
ep93xx_ide_release_gpio(pdev);
}
+static const struct of_device_id ep93xx_pata_of_ids[] = {
+ { .compatible = "cirrus,ep9312-pata" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, ep93xx_pata_of_ids);
+
static struct platform_driver ep93xx_pata_platform_driver = {
.driver = {
.name = DRV_NAME,
+ .of_match_table = ep93xx_pata_of_ids,
},
.probe = ep93xx_pata_probe,
.remove_new = ep93xx_pata_remove,
--
2.41.0
Thu, Jan 18, 2024 at 11:21:05AM +0300, Nikita Shubin kirjoitti:
> - add OF ID match table
> - drop platform DMA and filters
> - change DMA setup to OF, so we can defer probe
..
> + drv_data->dma_rx_channel = dma_request_chan(dev, "rx");
> + if (IS_ERR(drv_data->dma_rx_channel)) {
> + ret = PTR_ERR(drv_data->dma_rx_channel);
> + return dev_err_probe(dev, ret, "rx DMA setup failed\n");
It can be done in one statement:
return dev_err_probe(dev, PTR_ERR(drv_data->dma_rx_channel),
"rx DMA setup failed\n");
> + }
..
> + drv_data->dma_tx_channel = dma_request_chan(&pdev->dev, "tx");
> + if (IS_ERR(drv_data->dma_tx_channel)) {
> + ret = PTR_ERR(drv_data->dma_tx_channel);
> + dev_err_probe(dev, ret, "tx DMA setup failed\n");
In the similar way
ret = dev_err_probe(...);
> + goto fail_release_rx;
> }
--
With Best Regards,
Andy Shevchenko