From: Hiago De Franco <[email protected]>
This patch series introduces support for the new Apalis Evaluation Board
v1.2. With the introduction of v1.2, a common dtsi file, containing
shared configurations for both apalis-eval.dts and apalis-eval-v1.2.dts,
has been created. The eval and eval-v1.2 dts files will now capture the
differences between these two boards. Additionally, updates have been
made to nxp/imx/Makefile and arm/fsl.yaml to accommodate these changes.
Hiago De Franco (2):
dt-bindings: arm: fsl: Add toradex,apalis_imx6q-eval-v1.2 board
arm: dts: nxp: imx: Add support for Apalis Evaluation Board v1.2
.../devicetree/bindings/arm/fsl.yaml | 3 +-
arch/arm/boot/dts/nxp/imx/Makefile | 1 +
.../dts/nxp/imx/imx6q-apalis-eval-v1.2.dts | 198 ++++++++++++++++++
.../boot/dts/nxp/imx/imx6q-apalis-eval.dts | 108 +---------
.../boot/dts/nxp/imx/imx6q-apalis-eval.dtsi | 120 +++++++++++
5 files changed, 323 insertions(+), 107 deletions(-)
create mode 100644 arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts
create mode 100644 arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi
--
2.43.0
From: Hiago De Franco <[email protected]>
Add support for the new Apalis Evaluation Board v1.2. Because
only the imx6q-apalis-eval.dts was available, the imx6q-apalis-eval.dtsi
has been created which has common hardware configurations for v1.0, v1.1
and v1.2. Both imx6q-apalis-eval.dts and imx6q-apalis-eval-v1.2.dts
files include imx6q-apalis-eval.dtsi.
Versions 1.0 and 1.1 are compatible with each other and should
use imx6q-apalis-eval.dts file. Now for v1.2, the new device-tree file
should be used.
Signed-off-by: Hiago De Franco <[email protected]>
---
arch/arm/boot/dts/nxp/imx/Makefile | 1 +
.../dts/nxp/imx/imx6q-apalis-eval-v1.2.dts | 198 ++++++++++++++++++
.../boot/dts/nxp/imx/imx6q-apalis-eval.dts | 108 +---------
.../boot/dts/nxp/imx/imx6q-apalis-eval.dtsi | 120 +++++++++++
4 files changed, 321 insertions(+), 106 deletions(-)
create mode 100644 arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts
create mode 100644 arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi
diff --git a/arch/arm/boot/dts/nxp/imx/Makefile b/arch/arm/boot/dts/nxp/imx/Makefile
index a724d1a7a9a0..0473f9b86ec7 100644
--- a/arch/arm/boot/dts/nxp/imx/Makefile
+++ b/arch/arm/boot/dts/nxp/imx/Makefile
@@ -147,6 +147,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-yapp4-phoenix.dtb \
imx6dl-yapp4-ursa.dtb \
imx6q-apalis-eval.dtb \
+ imx6q-apalis-eval-v1.2.dtb \
imx6q-apalis-ixora.dtb \
imx6q-apalis-ixora-v1.1.dtb \
imx6q-apalis-ixora-v1.2.dtb \
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts
new file mode 100644
index 000000000000..2fba7ed1061c
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts
@@ -0,0 +1,198 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6q-apalis-eval.dtsi"
+
+/ {
+ model = "Toradex Apalis iMX6Q/D Module on Apalis Evaluation Board v1.2";
+ compatible = "toradex,apalis_imx6q-eval-v1.2", "toradex,apalis_imx6q",
+ "fsl,imx6q";
+
+ reg_3v3_mmc: regulator-3v3-mmc {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enable_3v3_mmc>;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "3.3V_MMC";
+ startup-delay-us = <100>;
+ };
+
+ reg_3v3_sd: regulator-3v3-sd {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enable_3v3_sd>;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "3.3V_SD";
+ startup-delay-us = <100>;
+ };
+
+ reg_can1: regulator-can1 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enable_can1_power>;
+ regulator-name = "5V_SW_CAN1";
+ startup-delay-us = <1000>;
+ };
+
+ reg_can2: regulator-can2 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enable_can2_power>;
+ regulator-name = "5V_SW_CAN2";
+ startup-delay-us = <1000>;
+ };
+
+ sound-carrier {
+ compatible = "simple-audio-card";
+ simple-audio-card,bitclock-master = <&codec_dai>;
+ simple-audio-card,format = "i2s";
+ simple-audio-card,frame-master = <&codec_dai>;
+ simple-audio-card,name = "apalis-nau8822";
+ simple-audio-card,routing =
+ "Headphones", "LHP",
+ "Headphones", "RHP",
+ "Speaker", "LSPK",
+ "Speaker", "RSPK",
+ "Line Out", "AUXOUT1",
+ "Line Out", "AUXOUT2",
+ "LAUX", "Line In",
+ "RAUX", "Line In",
+ "LMICP", "Mic In",
+ "RMICP", "Mic In";
+ simple-audio-card,widgets =
+ "Headphones", "Headphones",
+ "Line Out", "Line Out",
+ "Speaker", "Speaker",
+ "Microphone", "Mic In",
+ "Line", "Line In";
+
+ codec_dai: simple-audio-card,codec {
+ sound-dai = <&nau8822_1a>;
+ system-clock-frequency = <12288000>;
+ };
+
+ simple-audio-card,cpu {
+ sound-dai = <&ssi2>;
+ };
+ };
+};
+
+&can1 {
+ xceiver-supply = <®_can1>;
+ status = "okay";
+};
+
+&can2 {
+ xceiver-supply = <®_can2>;
+ status = "okay";
+};
+
+/* I2C1_SDA/SCL on MXM3 209/211 */
+&i2c1 {
+ /* Audio Codec */
+ nau8822_1a: audio-codec@1a {
+ compatible = "nuvoton,nau8822";
+ reg = <0x1a>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nau8822>;
+ #sound-dai-cells = <0>;
+ };
+
+ /* Current measurement into module VCC */
+ hwmon@40 {
+ compatible = "ti,ina219";
+ reg = <0x40>;
+ shunt-resistor = <5000>;
+ };
+
+ /* Temperature Sensor */
+ temperature-sensor@4f {
+ compatible = "ti,tmp75c";
+ reg = <0x4f>;
+ };
+
+ /* EEPROM */
+ eeprom@57 {
+ compatible = "st,24c02", "atmel,24c02";
+ reg = <0x57>;
+ pagesize = <16>;
+ size = <256>;
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&ssi2 {
+ status = "okay";
+};
+
+/* MMC1 */
+&usdhc1 {
+ bus-width = <4>;
+ pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_mmc_cd>;
+ vmmc-supply = <®_3v3_mmc>;
+ status = "okay";
+};
+
+/* SD1 */
+&usdhc2 {
+ cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&pinctrl_usdhc2 &pinctrl_sd_cd>;
+ vmmc-supply = <®_3v3_sd>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_enable_3v3_mmc: enable3v3mmcgrp {
+ fsl,pins = <
+ /* MMC1_PWR_CTRL */
+ MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0xb000
+ >;
+ };
+
+ pinctrl_enable_3v3_sd: enable3v3sdgrp {
+ fsl,pins = <
+ /* SD1_PWR_CTRL */
+ MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0xb000
+ >;
+ };
+
+ pinctrl_enable_can1_power: enablecan1powergrp {
+ fsl,pins = <
+ /* CAN1_PWR_EN */
+ MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0xb000
+ >;
+ };
+
+ pinctrl_enable_can2_power: enablecan2powergrp {
+ fsl,pins = <
+ /* CAN2_PWR_EN */
+ MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0xb000
+ >;
+ };
+
+ pinctrl_nau8822: nau8822grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT16__AUD5_TXC 0x130b0
+ MX6QDL_PAD_DISP0_DAT17__AUD5_TXD 0x130b0
+ MX6QDL_PAD_DISP0_DAT18__AUD5_TXFS 0x130b0
+ MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x130b0
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts
index 3fc079dfd61e..e1077e2da5f4 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts
@@ -7,29 +7,13 @@
/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include "imx6q.dtsi"
-#include "imx6qdl-apalis.dtsi"
+#include "imx6q-apalis-eval.dtsi"
/ {
model = "Toradex Apalis iMX6Q/D Module on Apalis Evaluation Board";
compatible = "toradex,apalis_imx6q-eval", "toradex,apalis_imx6q",
"fsl,imx6q";
- aliases {
- i2c0 = &i2c1;
- i2c1 = &i2c3;
- i2c2 = &i2c2;
- rtc0 = &rtc_i2c;
- rtc1 = &snvs_rtc;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
reg_pcie_switch: regulator-pcie-switch {
compatible = "regulator-fixed";
enable-active-high;
@@ -40,14 +24,6 @@ reg_pcie_switch: regulator-pcie-switch {
startup-delay-us = <100000>;
status = "okay";
};
-
- reg_3v3_sw: regulator-3v3-sw {
- compatible = "regulator-fixed";
- regulator-always-on;
- regulator-max-microvolt = <3300000>;
- regulator-min-microvolt = <3300000>;
- regulator-name = "3.3V_SW";
- };
};
&can1 {
@@ -62,102 +38,22 @@ &can2 {
/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
&i2c1 {
- status = "okay";
-
+ /* PCIe Switch */
pcie-switch@58 {
compatible = "plx,pex8605";
reg = <0x58>;
};
-
- /* M41T0M6 real time clock on carrier board */
- rtc_i2c: rtc@68 {
- compatible = "st,m41t0";
- reg = <0x68>;
- };
-};
-
-/*
- * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
- * board)
- */
-&i2c3 {
- status = "okay";
};
&pcie {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_reset_moci>;
- /* active-high meaning opposite of regular PERST# active-low polarity */
- reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
- reset-gpio-active-high;
vpcie-supply = <®_pcie_switch>;
status = "okay";
};
-&pwm1 {
- status = "okay";
-};
-
-&pwm2 {
- status = "okay";
-};
-
-&pwm3 {
- status = "okay";
-};
-
-&pwm4 {
- status = "okay";
-};
-
-®_usb_host_vbus {
- status = "okay";
-};
-
-®_usb_otg_vbus {
- status = "okay";
-};
-
-&sata {
- status = "okay";
-};
-
&sound_spdif {
status = "okay";
};
-&spdif {
- status = "okay";
-};
-
-&uart1 {
- status = "okay";
-};
-
-&uart2 {
- status = "okay";
-};
-
-&uart4 {
- status = "okay";
-};
-
-&uart5 {
- status = "okay";
-};
-
-&usbh1 {
- disable-over-current;
- vbus-supply = <®_usb_host_vbus>;
- status = "okay";
-};
-
-&usbotg {
- disable-over-current;
- vbus-supply = <®_usb_otg_vbus>;
- status = "okay";
-};
-
/* MMC1 */
&usdhc1 {
status = "okay";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi
new file mode 100644
index 000000000000..b6c45ad3f430
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi
@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2014-2024 Toradex
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6q.dtsi"
+#include "imx6qdl-apalis.dtsi"
+
+/ {
+ aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c3;
+ i2c2 = &i2c2;
+ rtc0 = &rtc_i2c;
+ rtc1 = &snvs_rtc;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ reg_3v3_sw: regulator-3v3-sw {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "3.3V_SW";
+ };
+};
+
+&i2c1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ /* M41T0M6 real time clock on carrier board */
+ rtc_i2c: rtc@68 {
+ compatible = "st,m41t0";
+ reg = <0x68>;
+ };
+};
+
+/*
+ * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
+ * board)
+ */
+&i2c3 {
+ status = "okay";
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reset_moci>;
+ /* active-high meaning opposite of regular PERST# active-low polarity */
+ reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ reset-gpio-active-high;
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&pwm3 {
+ status = "okay";
+};
+
+&pwm4 {
+ status = "okay";
+};
+
+®_usb_host_vbus {
+ status = "okay";
+};
+
+®_usb_otg_vbus {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&spdif {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+};
+
+&uart5 {
+ status = "okay";
+};
+
+&usbh1 {
+ disable-over-current;
+ vbus-supply = <®_usb_host_vbus>;
+ status = "okay";
+};
+
+&usbotg {
+ disable-over-current;
+ vbus-supply = <®_usb_otg_vbus>;
+ status = "okay";
+};
--
2.43.0
On Mon, Jan 22, 2024 at 09:35:00AM -0300, Hiago De Franco wrote:
> From: Hiago De Franco <[email protected]>
>
> Add support for the new Apalis Evaluation Board v1.2. Because
> only the imx6q-apalis-eval.dts was available, the imx6q-apalis-eval.dtsi
> has been created which has common hardware configurations for v1.0, v1.1
> and v1.2. Both imx6q-apalis-eval.dts and imx6q-apalis-eval-v1.2.dts
> files include imx6q-apalis-eval.dtsi.
>
> Versions 1.0 and 1.1 are compatible with each other and should
> use imx6q-apalis-eval.dts file. Now for v1.2, the new device-tree file
> should be used.
>
> Signed-off-by: Hiago De Franco <[email protected]>
Reviewed-by: Francesco Dolcini <[email protected]>
Hello Shawn,
On Mon, Jan 22, 2024 at 09:34:58AM -0300, Hiago De Franco wrote:
> From: Hiago De Franco <[email protected]>
>
> This patch series introduces support for the new Apalis Evaluation Board
> v1.2. With the introduction of v1.2, a common dtsi file, containing
> shared configurations for both apalis-eval.dts and apalis-eval-v1.2.dts,
> has been created. The eval and eval-v1.2 dts files will now capture the
> differences between these two boards. Additionally, updates have been
> made to nxp/imx/Makefile and arm/fsl.yaml to accommodate these changes.
We found a couple of late issues during some additional testing on the
DTS, some regulator delays are not correct. Hiago will send a v2 in the
next couple of days.
Thanks,
Francesco