This patch series adds power-supply properties for sdmmc nodes on Microchip boards.
Mihai Sain (8):
ARM: dts: microchip: sam9x60_curiosity: Add power-supply properties for sdmmc nodes
ARM: dts: microchip: sam9x60ek: Add power-supply properties for sdmmc nodes
ARM: dts: microchip: sama5d27_som1_ek: Add power-supply properties for sdmmc nodes
ARM: dts: microchip: sama5d27_wlsom1: Add power-supply property for sdmmc1 node
ARM: dts: microchip: sama5d27_wlsom1_ek: Add power-supply property for sdmmc0 node
ARM: dts: microchip: sama5d29_curiosity: Add power-supply properties for sdmmc nodes
ARM: dts: microchip: sama5d2_icp: Add power-supply property for sdmmc0 node
ARM: dts: microchip: sama5d2_xplained: Add power-supply property for sdmmc0 node
arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts | 4 ++++
arch/arm/boot/dts/microchip/at91-sam9x60ek.dts | 4 ++++
arch/arm/boot/dts/microchip/at91-sama5d27_som1_ek.dts | 4 ++++
arch/arm/boot/dts/microchip/at91-sama5d27_wlsom1.dtsi | 2 ++
arch/arm/boot/dts/microchip/at91-sama5d27_wlsom1_ek.dts | 2 ++
arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts | 4 ++++
arch/arm/boot/dts/microchip/at91-sama5d2_icp.dts | 2 ++
arch/arm/boot/dts/microchip/at91-sama5d2_xplained.dts | 2 ++
8 files changed, 24 insertions(+)
--
2.43.0
The sdmmc0 and sdmmc1 controllers are powered from 3.3V regulator.
Add vmmc-supply and vqmmc-supply properties to sdmmc nodes.
Signed-off-by: Mihai Sain <[email protected]>
---
arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts b/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
index c6fbdd29019f..457c54dde0b7 100644
--- a/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
+++ b/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
@@ -452,6 +452,8 @@ &sdmmc0 {
pinctrl-0 = <&pinctrl_sdmmc0_default &pinctrl_sdmmc0_cd>;
cd-gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
disable-wp;
+ vmmc-supply = <&vdd1_3v3>;
+ vqmmc-supply = <&vdd1_3v3>;
status = "okay";
};
@@ -460,6 +462,8 @@ &sdmmc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdmmc1_default>;
disable-wp;
+ vmmc-supply = <&vdd1_3v3>;
+ vqmmc-supply = <&vdd1_3v3>;
status = "okay";
};
--
2.43.0
The sdmmc0 and sdmmc1 controllers are powered from 3.3V regulator.
Add vmmc-supply and vqmmc-supply properties to sdmmc nodes.
Signed-off-by: Mihai Sain <[email protected]>
---
arch/arm/boot/dts/microchip/at91-sama5d27_som1_ek.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/microchip/at91-sama5d27_som1_ek.dts b/arch/arm/boot/dts/microchip/at91-sama5d27_som1_ek.dts
index f3ffb8f01d8a..255ee0640133 100644
--- a/arch/arm/boot/dts/microchip/at91-sama5d27_som1_ek.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d27_som1_ek.dts
@@ -56,6 +56,8 @@ sdmmc0: sdio-host@a0000000 {
bus-width = <8>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdmmc0_default>;
+ vmmc-supply = <&vddin_3v3>;
+ vqmmc-supply = <&vddin_3v3>;
status = "okay";
};
@@ -63,6 +65,8 @@ sdmmc1: sdio-host@b0000000 {
bus-width = <4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdmmc1_default>;
+ vmmc-supply = <&vddin_3v3>;
+ vqmmc-supply = <&vddin_3v3>;
status = "okay";
};
--
2.43.0
The sdmmc0 controller is powered from 3.3V regulator.
Add vmmc-supply and vqmmc-supply properties to sdmmc0 node.
Signed-off-by: Mihai Sain <[email protected]>
---
arch/arm/boot/dts/microchip/at91-sama5d27_wlsom1_ek.dts | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/microchip/at91-sama5d27_wlsom1_ek.dts b/arch/arm/boot/dts/microchip/at91-sama5d27_wlsom1_ek.dts
index 15239834d886..7b36e1970bb7 100644
--- a/arch/arm/boot/dts/microchip/at91-sama5d27_wlsom1_ek.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d27_wlsom1_ek.dts
@@ -199,6 +199,8 @@ &sdmmc0 {
bus-width = <4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdmmc0_default>;
+ vmmc-supply = <&vdd_3v3>;
+ vqmmc-supply = <&vdd_3v3>;
status = "okay";
};
--
2.43.0
The sdmmc0 controller is powered from 3.3V regulator.
Add vmmc-supply and vqmmc-supply properties to sdmmc0 node.
Signed-off-by: Mihai Sain <[email protected]>
---
arch/arm/boot/dts/microchip/at91-sama5d2_icp.dts | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/microchip/at91-sama5d2_icp.dts b/arch/arm/boot/dts/microchip/at91-sama5d2_icp.dts
index 999adeca6f33..adcb3240e5f5 100644
--- a/arch/arm/boot/dts/microchip/at91-sama5d2_icp.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d2_icp.dts
@@ -712,6 +712,8 @@ &sdmmc0 {
bus-width = <4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdmmc0_default>;
+ vmmc-supply = <&vdd_io_reg>; // 3.3V
+ vqmmc-supply = <&vdd_io_reg>; // 3.3V
status = "okay";
};
--
2.43.0
The sdmmc0 and sdmmc1 controllers are powered from 3.3V regulator.
Add vmmc-supply and vqmmc-supply properties to sdmmc nodes.
Signed-off-by: Mihai Sain <[email protected]>
---
arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts b/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts
index 6b02b7bcfd49..4a86597d089a 100644
--- a/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts
@@ -504,6 +504,8 @@ &sdmmc0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdmmc0_default>;
disable-wp;
+ vmmc-supply = <&vdd_3v3>;
+ vqmmc-supply = <&vdd_3v3>;
status = "okay";
};
@@ -512,6 +514,8 @@ &sdmmc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdmmc1_default>;
disable-wp;
+ vmmc-supply = <&vdd_3v3>;
+ vqmmc-supply = <&vdd_3v3>;
status = "okay";
};
--
2.43.0
The sdmmc0 and sdmmc1 controllers are powered from 3.3V regulator.
Add vmmc-supply and vqmmc-supply properties to sdmmc nodes.
Signed-off-by: Mihai Sain <[email protected]>
---
arch/arm/boot/dts/microchip/at91-sam9x60ek.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/microchip/at91-sam9x60ek.dts b/arch/arm/boot/dts/microchip/at91-sam9x60ek.dts
index f3cbb675cea4..b19a0956dc97 100644
--- a/arch/arm/boot/dts/microchip/at91-sam9x60ek.dts
+++ b/arch/arm/boot/dts/microchip/at91-sam9x60ek.dts
@@ -560,6 +560,8 @@ &sdmmc0 {
status = "okay";
cd-gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
disable-wp;
+ vmmc-supply = <&vdd1_3v3>;
+ vqmmc-supply = <&vdd1_3v3>;
};
&sdmmc1 {
@@ -568,6 +570,8 @@ &sdmmc1 {
pinctrl-0 = <&pinctrl_sdmmc1_default>;
no-1-8-v;
non-removable;
+ vmmc-supply = <&vdd1_3v3>;
+ vqmmc-supply = <&vdd1_3v3>;
status = "disabled"; /* Conflict with flx4. */
};
--
2.43.0
The sdmmc0 controller is powered from 3.3V regulator.
Add vmmc-supply and vqmmc-supply properties to sdmmc0 node.
Signed-off-by: Mihai Sain <[email protected]>
---
arch/arm/boot/dts/microchip/at91-sama5d2_xplained.dts | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/microchip/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/microchip/at91-sama5d2_xplained.dts
index 6680031387e8..9b7e56790a5a 100644
--- a/arch/arm/boot/dts/microchip/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d2_xplained.dts
@@ -67,6 +67,8 @@ sdmmc0: sdio-host@a0000000 {
pinctrl-0 = <&pinctrl_sdmmc0_default>;
non-removable;
mmc-ddr-3_3v;
+ vmmc-supply = <&vdd_3v3_reg>;
+ vqmmc-supply = <&vdd_3v3_reg>;
status = "okay";
};
--
2.43.0
On 23/01/2024 09:31, Mihai Sain wrote:
> The sdmmc0 and sdmmc1 controllers are powered from 3.3V regulator.
> Add vmmc-supply and vqmmc-supply properties to sdmmc nodes.
>
> Signed-off-by: Mihai Sain <[email protected]>
> ---
> arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts | 4 ++++
> 1 file changed, 4 insertions(+)
>
> diff --git a/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts b/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
> index c6fbdd29019f..457c54dde0b7 100644
> --- a/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
> +++ b/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
> @@ -452,6 +452,8 @@ &sdmmc0 {
> pinctrl-0 = <&pinctrl_sdmmc0_default &pinctrl_sdmmc0_cd>;
> cd-gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
> disable-wp;
> + vmmc-supply = <&vdd1_3v3>;
> + vqmmc-supply = <&vdd1_3v3>;
For this and all other patches:
It is surprising that you use the same supply for both. Looks like
inaccurate description. It is possible, but I think unlikely because
usually VQMMC has lower voltage than 3.3V.
Best regards,
Krzysztof
Hi Krzysztof,
I'm sorry for quoting (email is sent from Outlook).
The sdmmc controller from SAM9 MPUs doesn't support the IO voltage signaling/switching required by the UHS sd-card.
On the electrical schematics of the boards the controller and sd-card power pins are connected to 3V3 regulator.
On the SAMA5 MPUs there is support for IO voltage switching but since we have issues with the tuning procedure required but the UHS cards,
we want to keep vqmmc at 3V3 in order to use high-speed mode.
Best regards,
Mihai Sain
----------------------------------------------------------------------
> diff --git a/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
> b/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
> index c6fbdd29019f..457c54dde0b7 100644
> --- a/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
> +++ b/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
> @@ -452,6 +452,8 @@ &sdmmc0 {
> pinctrl-0 = <&pinctrl_sdmmc0_default &pinctrl_sdmmc0_cd>;
> cd-gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
> disable-wp;
> + vmmc-supply = <&vdd1_3v3>;
> + vqmmc-supply = <&vdd1_3v3>;
For this and all other patches:
It is surprising that you use the same supply for both. Looks like inaccurate description. It is possible, but I think unlikely because usually VQMMC has lower voltage than 3.3V.
Best regards,
Krzysztof
On 23/01/2024 10:07, [email protected] wrote:
> Hi Krzysztof,
>
> I'm sorry for quoting (email is sent from Outlook).
> The sdmmc controller from SAM9 MPUs doesn't support the IO voltage signaling/switching required by the UHS sd-card.
> On the electrical schematics of the boards the controller and sd-card power pins are connected to 3V3 regulator.
> On the SAMA5 MPUs there is support for IO voltage switching but since we have issues with the tuning procedure required but the UHS cards,
> we want to keep vqmmc at 3V3 in order to use high-speed mode.
OK, it is fine for me.
Best regards,
Krzysztof
Hi, Mihai,
On 23.01.2024 11:07, [email protected] wrote:
> Hi Krzysztof,
>
> I'm sorry for quoting (email is sent from Outlook).
> The sdmmc controller from SAM9 MPUs doesn't support the IO voltage signaling/switching required by the UHS sd-card.
> On the electrical schematics of the boards the controller and sd-card power pins are connected to 3V3 regulator.
> On the SAMA5 MPUs there is support for IO voltage switching but since we have issues with the tuning procedure required but the UHS cards,
> we want to keep vqmmc at 3V3 in order to use high-speed mode.
Can you capture this information in each patch description?
>
> Best regards,
> Mihai Sain
>
> ----------------------------------------------------------------------
>
>> diff --git a/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
>> b/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
>> index c6fbdd29019f..457c54dde0b7 100644
>> --- a/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
>> +++ b/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
>> @@ -452,6 +452,8 @@ &sdmmc0 {
>> pinctrl-0 = <&pinctrl_sdmmc0_default &pinctrl_sdmmc0_cd>;
>> cd-gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
>> disable-wp;
>> + vmmc-supply = <&vdd1_3v3>;
>> + vqmmc-supply = <&vdd1_3v3>;
>
> For this and all other patches:
>
> It is surprising that you use the same supply for both. Looks like inaccurate description. It is possible, but I think unlikely because usually VQMMC has lower voltage than 3.3V.
>
> Best regards,
> Krzysztof
>