From: Siddharth Vadapalli <[email protected]>
J784S4 SoC has a 9 port Ethernet Switch instance with 8 external
ports and 1 host port, referred to as CPSW9G.
Add device-tree nodes for CPSW9G and disable it by default.
Device-tree overlays will be used to enable it.
Add device-tree nodes for Main CPSW2G nodes and disable it
by default.
Signed-off-by: Siddharth Vadapalli <[email protected]>
Signed-off-by: Chintan Vankar <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 182 +++++++++++++++++++++
1 file changed, 182 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
index 56c8eaad6324..89578b449450 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
@@ -47,6 +47,19 @@ scm_conf: bus@100000 {
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x00 0x00 0x00100000 0x1c000>;
+
+ cpsw1_phy_gmii_sel: phy@4034 {
+ compatible = "ti,am654-phy-gmii-sel";
+ reg = <0x4034 0x4>;
+ #phy-cells = <1>;
+ };
+
+ cpsw0_phy_gmii_sel: phy@4044 {
+ compatible = "ti,j784s4-cpsw9g-phy-gmii-sel";
+ ti,qsgmii-main-ports = <7>, <7>;
+ reg = <0x4044 0x20>;
+ #phy-cells = <1>;
+ };
serdes_ln_ctrl: mux-controller@4080 {
compatible = "reg-mux";
@@ -1242,6 +1255,175 @@ cpts@310d0000 {
};
};
+ main_cpsw0: ethernet@c000000 {
+ compatible = "ti,j784s4-cpswxg-nuss";
+ reg = <0x00 0xc000000 0x00 0x200000>;
+ reg-names = "cpsw_nuss";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x00 0x00 0x00 0xc000000 0x00 0x200000>;
+ dma-coherent;
+ clocks = <&k3_clks 64 0>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 64 TI_SCI_PD_EXCLUSIVE>;
+
+ dmas = <&main_udmap 0xca00>,
+ <&main_udmap 0xca01>,
+ <&main_udmap 0xca02>,
+ <&main_udmap 0xca03>,
+ <&main_udmap 0xca04>,
+ <&main_udmap 0xca05>,
+ <&main_udmap 0xca06>,
+ <&main_udmap 0xca07>,
+ <&main_udmap 0x4a00>;
+ dma-names = "tx0", "tx1", "tx2", "tx3",
+ "tx4", "tx5", "tx6", "tx7",
+ "rx";
+
+ status = "disabled";
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ main_cpsw0_port1: port@1 {
+ reg = <1>;
+ label = "port1";
+ ti,mac-only;
+ status = "disabled";
+ };
+
+ main_cpsw0_port2: port@2 {
+ reg = <2>;
+ label = "port2";
+ ti,mac-only;
+ status = "disabled";
+ };
+
+ main_cpsw0_port3: port@3 {
+ reg = <3>;
+ label = "port3";
+ ti,mac-only;
+ status = "disabled";
+ };
+
+ main_cpsw0_port4: port@4 {
+ reg = <4>;
+ label = "port4";
+ ti,mac-only;
+ status = "disabled";
+ };
+
+ main_cpsw0_port5: port@5 {
+ reg = <5>;
+ label = "port5";
+ status = "disabled";
+ };
+
+ main_cpsw0_port6: port@6 {
+ reg = <6>;
+ label = "port6";
+ status = "disabled";
+ };
+
+ main_cpsw0_port7: port@7 {
+ reg = <7>;
+ label = "port7";
+ status = "disabled";
+ };
+
+ main_cpsw0_port8: port@8 {
+ reg = <8>;
+ label = "port8";
+ status = "disabled";
+ };
+ };
+
+ main_cpsw0_mdio: mdio@f00 {
+ compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+ reg = <0x00 0xf00 0x00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&k3_clks 64 0>;
+ clock-names = "fck";
+ bus_freq = <1000000>;
+ status = "disabled";
+ };
+
+ cpts@3d000 {
+ compatible = "ti,am65-cpts";
+ reg = <0x00 0x3d000 0x00 0x400>;
+ clocks = <&k3_clks 64 3>;
+ clock-names = "cpts";
+ interrupts-extended = <&gic500 GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "cpts";
+ ti,cpts-ext-ts-inputs = <4>;
+ ti,cpts-periodic-outputs = <2>;
+ };
+ };
+
+ main_cpsw1: ethernet@c200000 {
+ compatible = "ti,j721e-cpsw-nuss";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ reg = <0x00 0xc200000 0x00 0x200000>;
+ reg-names = "cpsw_nuss";
+ ranges = <0x00 0x00 0x00 0xc200000 0x00 0x200000>;
+ dma-coherent;
+ clocks = <&k3_clks 62 0>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 62 TI_SCI_PD_EXCLUSIVE>;
+
+ dmas = <&main_udmap 0xc640>,
+ <&main_udmap 0xc641>,
+ <&main_udmap 0xc642>,
+ <&main_udmap 0xc643>,
+ <&main_udmap 0xc644>,
+ <&main_udmap 0xc645>,
+ <&main_udmap 0xc646>,
+ <&main_udmap 0xc647>,
+ <&main_udmap 0x4640>;
+ dma-names = "tx0", "tx1", "tx2", "tx3",
+ "tx4", "tx5", "tx6", "tx7",
+ "rx";
+
+ status = "disabled";
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ main_cpsw1_port1: port@1 {
+ reg = <1>;
+ label = "port1";
+ phys = <&cpsw1_phy_gmii_sel 1>;
+ ti,mac-only;
+ status = "disabled";
+ };
+ };
+
+ main_cpsw1_mdio: mdio@f00 {
+ compatible = "ti,cpsw-mdio", "ti,davinci_mdio";
+ reg = <0x00 0xf00 0x00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&k3_clks 62 0>;
+ clock-names = "fck";
+ bus_freq = <1000000>;
+ };
+
+ cpts@3d000 {
+ compatible = "ti,am65-cpts";
+ reg = <0x00 0x3d000 0x00 0x400>;
+ clocks = <&k3_clks 62 3>;
+ clock-names = "cpts";
+ interrupts-extended = <&gic500 GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "cpts";
+ ti,cpts-ext-ts-inputs = <4>;
+ ti,cpts-periodic-outputs = <2>;
+ };
+ };
+
main_mcan0: can@2701000 {
compatible = "bosch,m_can";
reg = <0x00 0x02701000 0x00 0x200>,
--
2.34.1
Hello Chintan,
On 25/01/24 15:34, Chintan Vankar wrote:
> From: Siddharth Vadapalli <[email protected]>
>
..
>
> + main_cpsw0: ethernet@c000000 {
> + compatible = "ti,j784s4-cpswxg-nuss";
> + reg = <0x00 0xc000000 0x00 0x200000>;
> + reg-names = "cpsw_nuss";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges = <0x00 0x00 0x00 0xc000000 0x00 0x200000>;
> + dma-coherent;
> + clocks = <&k3_clks 64 0>;
> + clock-names = "fck";
> + power-domains = <&k3_pds 64 TI_SCI_PD_EXCLUSIVE>;
> +
> + dmas = <&main_udmap 0xca00>,
> + <&main_udmap 0xca01>,
> + <&main_udmap 0xca02>,
> + <&main_udmap 0xca03>,
> + <&main_udmap 0xca04>,
> + <&main_udmap 0xca05>,
> + <&main_udmap 0xca06>,
> + <&main_udmap 0xca07>,
> + <&main_udmap 0x4a00>;
> + dma-names = "tx0", "tx1", "tx2", "tx3",
> + "tx4", "tx5", "tx6", "tx7",
> + "rx";
> +
> + status = "disabled";
> +
> + ethernet-ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + main_cpsw0_port1: port@1 {
> + reg = <1>;
> + label = "port1";
> + ti,mac-only;
> + status = "disabled";
> + };
> +
> + main_cpsw0_port2: port@2 {
> + reg = <2>;
> + label = "port2";
> + ti,mac-only;
> + status = "disabled";
> + };
> +
> + main_cpsw0_port3: port@3 {
> + reg = <3>;
> + label = "port3";
> + ti,mac-only;
> + status = "disabled";
> + };
> +
> + main_cpsw0_port4: port@4 {
> + reg = <4>;
> + label = "port4";
> + ti,mac-only;
> + status = "disabled";
> + };
> +
> + main_cpsw0_port5: port@5 {
> + reg = <5>;
> + label = "port5";
Please add the "ti,mac-only" property here and in the following 3 nodes as well
to keep it consistent.
> + status = "disabled";
> + };
> +
> + main_cpsw0_port6: port@6 {
> + reg = <6>;
> + label = "port6";
> + status = "disabled";
> + };
> +
> + main_cpsw0_port7: port@7 {
> + reg = <7>;
> + label = "port7";
> + status = "disabled";
> + };
> +
> + main_cpsw0_port8: port@8 {
> + reg = <8>;
> + label = "port8";
> + status = "disabled";
> + };
> + };
> +
..
--
Regards,
Siddharth.