Hello everyone,
Here's a V6 for the link topo and multi-phy support series.
Most of the changes were from Jakub's and Russell's reviews, the main
point being a rework of the netlink API, removing uneeded nests and
cleaning-up the dump code. Thanks's Jakub for all the tips, hopefulle
the API is cleaner now.
Another change is that we now try to re-use the phy index if possible,
but I couldn't reliably have this and the alloc-topology-on-first-attached-phy
feature as well, with the risk of assigning the same index to different
PHYs when setting an interface down then up again.
Here's what the new listings would look like :
- eth0 has a 88x3310 acting as media converter, and an SFP module with
an embedded 88e1111 PHY
- eth2 has a 88e1510 PHY
# ethtool --show-phys *
PHY for eth0:
PHY index: 1
Driver name: mv88x3310
PHY device name: f212a600.mdio-mii:00
Downstream SFP bus name: sfp-eth0
PHY id: 0
Upstream type: MAC
PHY for eth0:
PHY index: 2
Driver name: Marvell 88E1111
PHY device name: i2c:sfp-eth0:16
PHY id: 21040322
Upstream type: PHY
Upstream PHY index: 1
Upstream SFP name: sfp-eth0
PHY for eth2:
PHY index: 1
Driver name: Marvell 88E1510
PHY device name: f212a200.mdio-mii:00
PHY id: 21040593
Upstream type: MAC
Ethtool patches : https://github.com/minimaxwell/ethtool/tree/link-topo-v6
Link to V5: https://lore.kernel.org/netdev/[email protected]/
Link to V4: https://lore.kernel.org/netdev/[email protected]/
Link to V3: https://lore.kernel.org/netdev/[email protected]/
Link to V2: https://lore.kernel.org/netdev/[email protected]/
Link to V1: https://lore.kernel.org/netdev/[email protected]/
Maxime Chevallier (13):
net: phy: Introduce ethernet link topology representation
net: sfp: pass the phy_device when disconnecting an sfp module's PHY
net: phy: add helpers to handle sfp phy connect/disconnect
net: sfp: Add helper to return the SFP bus name
net: ethtool: Allow passing a phy index for some commands
netlink: specs: add phy-index as a header parameter
net: ethtool: Introduce a command to list PHYs on an interface
netlink: specs: add ethnl PHY_GET command set
net: ethtool: plca: Target the command to the requested PHY
net: ethtool: pse-pd: Target the command to the requested PHY
net: ethtool: cable-test: Target the command to the requested PHY
net: ethtool: strset: Allow querying phy stats by index
Documentation: networking: document phy_link_topology
Documentation/netlink/specs/ethtool.yaml | 62 ++++
Documentation/networking/ethtool-netlink.rst | 46 +++
Documentation/networking/index.rst | 1 +
.../networking/phy-link-topology.rst | 121 +++++++
MAINTAINERS | 2 +
drivers/net/phy/Makefile | 2 +-
drivers/net/phy/at803x.c | 2 +
drivers/net/phy/marvell-88x2222.c | 2 +
drivers/net/phy/marvell.c | 2 +
drivers/net/phy/marvell10g.c | 2 +
drivers/net/phy/phy_device.c | 55 ++++
drivers/net/phy/phy_link_topology.c | 105 ++++++
drivers/net/phy/phylink.c | 3 +-
drivers/net/phy/sfp-bus.c | 15 +-
include/linux/netdevice.h | 4 +-
include/linux/phy.h | 6 +
include/linux/phy_link_topology.h | 72 +++++
include/linux/phy_link_topology_core.h | 25 ++
include/linux/sfp.h | 8 +-
include/uapi/linux/ethtool.h | 16 +
include/uapi/linux/ethtool_netlink.h | 21 ++
net/core/dev.c | 9 +
net/ethtool/Makefile | 2 +-
net/ethtool/cabletest.c | 16 +-
net/ethtool/netlink.c | 53 +++-
net/ethtool/netlink.h | 10 +
net/ethtool/phy.c | 298 ++++++++++++++++++
net/ethtool/plca.c | 19 +-
net/ethtool/pse-pd.c | 13 +-
net/ethtool/strset.c | 17 +-
30 files changed, 966 insertions(+), 43 deletions(-)
create mode 100644 Documentation/networking/phy-link-topology.rst
create mode 100644 drivers/net/phy/phy_link_topology.c
create mode 100644 include/linux/phy_link_topology.h
create mode 100644 include/linux/phy_link_topology_core.h
create mode 100644 net/ethtool/phy.c
--
2.43.0
Some netlink commands are target towards ethernet PHYs, to control some
of their features. As there's several such commands, add the ability to
pass a PHY index in the ethnl request, which will populate the generic
ethnl_req_info with the relevant phydev when the command targets a PHY.
Signed-off-by: Maxime Chevallier <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
---
V6: - Added dedicated policies when passing a PHY index
- Dropped Andrew's R-b as there were changes
V5: - Added Andrew's R-b
- Fix a typo reported by Simon
V4: - No Changes
V3: - Fixed the documentation
V2: - New patch
Documentation/networking/ethtool-netlink.rst | 7 ++++
include/uapi/linux/ethtool_netlink.h | 1 +
net/ethtool/netlink.c | 44 +++++++++++++++++++-
net/ethtool/netlink.h | 5 +++
4 files changed, 55 insertions(+), 2 deletions(-)
diff --git a/Documentation/networking/ethtool-netlink.rst b/Documentation/networking/ethtool-netlink.rst
index d583d9abf2f8..3ca6c21e74af 100644
--- a/Documentation/networking/ethtool-netlink.rst
+++ b/Documentation/networking/ethtool-netlink.rst
@@ -57,6 +57,7 @@ Structure of this header is
``ETHTOOL_A_HEADER_DEV_INDEX`` u32 device ifindex
``ETHTOOL_A_HEADER_DEV_NAME`` string device name
``ETHTOOL_A_HEADER_FLAGS`` u32 flags common for all requests
+ ``ETHTOOL_A_HEADER_PHY_INDEX`` u32 phy device index
============================== ====== =============================
``ETHTOOL_A_HEADER_DEV_INDEX`` and ``ETHTOOL_A_HEADER_DEV_NAME`` identify the
@@ -81,6 +82,12 @@ the behaviour is backward compatible, i.e. requests from old clients not aware
of the flag should be interpreted the way the client expects. A client must
not set flags it does not understand.
+``ETHTOOL_A_HEADER_PHY_INDEX`` identify the ethernet PHY the message relates to.
+As there are numerous commands that are related to PHY configuration, and because
+we can have more than one PHY on the link, the PHY index can be passed in the
+request for the commands that needs it. It is however not mandatory, and if it
+is not passed for commands that target a PHY, the net_device.phydev pointer
+is used, as a fallback that keeps the legacy behaviour.
Bit sets
========
diff --git a/include/uapi/linux/ethtool_netlink.h b/include/uapi/linux/ethtool_netlink.h
index 3f89074aa06c..422e8cfdd98c 100644
--- a/include/uapi/linux/ethtool_netlink.h
+++ b/include/uapi/linux/ethtool_netlink.h
@@ -133,6 +133,7 @@ enum {
ETHTOOL_A_HEADER_DEV_INDEX, /* u32 */
ETHTOOL_A_HEADER_DEV_NAME, /* string */
ETHTOOL_A_HEADER_FLAGS, /* u32 - ETHTOOL_FLAG_* */
+ ETHTOOL_A_HEADER_PHY_INDEX, /* u32 */
/* add new constants above here */
__ETHTOOL_A_HEADER_CNT,
diff --git a/net/ethtool/netlink.c b/net/ethtool/netlink.c
index fe3553f60bf3..5a9beb09e5d4 100644
--- a/net/ethtool/netlink.c
+++ b/net/ethtool/netlink.c
@@ -4,6 +4,7 @@
#include <linux/ethtool_netlink.h>
#include <linux/pm_runtime.h>
#include "netlink.h"
+#include <linux/phy_link_topology.h>
static struct genl_family ethtool_genl_family;
@@ -30,6 +31,24 @@ const struct nla_policy ethnl_header_policy_stats[] = {
ETHTOOL_FLAGS_STATS),
};
+const struct nla_policy ethnl_header_policy_phy[] = {
+ [ETHTOOL_A_HEADER_DEV_INDEX] = { .type = NLA_U32 },
+ [ETHTOOL_A_HEADER_DEV_NAME] = { .type = NLA_NUL_STRING,
+ .len = ALTIFNAMSIZ - 1 },
+ [ETHTOOL_A_HEADER_FLAGS] = NLA_POLICY_MASK(NLA_U32,
+ ETHTOOL_FLAGS_BASIC),
+ [ETHTOOL_A_HEADER_PHY_INDEX] = NLA_POLICY_MIN(NLA_U32, 1),
+};
+
+const struct nla_policy ethnl_header_policy_phy_stats[] = {
+ [ETHTOOL_A_HEADER_DEV_INDEX] = { .type = NLA_U32 },
+ [ETHTOOL_A_HEADER_DEV_NAME] = { .type = NLA_NUL_STRING,
+ .len = ALTIFNAMSIZ - 1 },
+ [ETHTOOL_A_HEADER_FLAGS] = NLA_POLICY_MASK(NLA_U32,
+ ETHTOOL_FLAGS_STATS),
+ [ETHTOOL_A_HEADER_PHY_INDEX] = NLA_POLICY_MIN(NLA_U32, 1),
+};
+
int ethnl_ops_begin(struct net_device *dev)
{
int ret;
@@ -89,8 +108,9 @@ int ethnl_parse_header_dev_get(struct ethnl_req_info *req_info,
const struct nlattr *header, struct net *net,
struct netlink_ext_ack *extack, bool require_dev)
{
- struct nlattr *tb[ARRAY_SIZE(ethnl_header_policy)];
+ struct nlattr *tb[ARRAY_SIZE(ethnl_header_policy_phy)];
const struct nlattr *devname_attr;
+ struct phy_device *phydev = NULL;
struct net_device *dev = NULL;
u32 flags = 0;
int ret;
@@ -104,7 +124,7 @@ int ethnl_parse_header_dev_get(struct ethnl_req_info *req_info,
/* No validation here, command policy should have a nested policy set
* for the header, therefore validation should have already been done.
*/
- ret = nla_parse_nested(tb, ARRAY_SIZE(ethnl_header_policy) - 1, header,
+ ret = nla_parse_nested(tb, ARRAY_SIZE(ethnl_header_policy_phy) - 1, header,
NULL, extack);
if (ret < 0)
return ret;
@@ -145,6 +165,26 @@ int ethnl_parse_header_dev_get(struct ethnl_req_info *req_info,
return -EINVAL;
}
+ if (dev) {
+ if (tb[ETHTOOL_A_HEADER_PHY_INDEX]) {
+ u32 phy_index = nla_get_u32(tb[ETHTOOL_A_HEADER_PHY_INDEX]);
+
+ phydev = phy_link_topo_get_phy(dev->link_topo,
+ phy_index);
+ if (!phydev) {
+ NL_SET_ERR_MSG_ATTR(extack, header,
+ "no phy matches phy index");
+ return -EINVAL;
+ }
+ } else {
+ /* If we need a PHY but no phy index is specified, fallback
+ * to dev->phydev
+ */
+ phydev = dev->phydev;
+ }
+ }
+
+ req_info->phydev = phydev;
req_info->dev = dev;
req_info->flags = flags;
return 0;
diff --git a/net/ethtool/netlink.h b/net/ethtool/netlink.h
index 9a333a8d04c1..d57a890b5d9e 100644
--- a/net/ethtool/netlink.h
+++ b/net/ethtool/netlink.h
@@ -250,6 +250,7 @@ static inline unsigned int ethnl_reply_header_size(void)
* @dev: network device the request is for (may be null)
* @dev_tracker: refcount tracker for @dev reference
* @flags: request flags common for all request types
+ * @phydev: phy_device connected to @dev this request is for (may be null)
*
* This is a common base for request specific structures holding data from
* parsed userspace request. These always embed struct ethnl_req_info at
@@ -259,6 +260,7 @@ struct ethnl_req_info {
struct net_device *dev;
netdevice_tracker dev_tracker;
u32 flags;
+ struct phy_device *phydev;
};
static inline void ethnl_parse_header_dev_put(struct ethnl_req_info *req_info)
@@ -395,9 +397,12 @@ extern const struct ethnl_request_ops ethnl_rss_request_ops;
extern const struct ethnl_request_ops ethnl_plca_cfg_request_ops;
extern const struct ethnl_request_ops ethnl_plca_status_request_ops;
extern const struct ethnl_request_ops ethnl_mm_request_ops;
+extern const struct ethnl_request_ops ethnl_phy_request_ops;
extern const struct nla_policy ethnl_header_policy[ETHTOOL_A_HEADER_FLAGS + 1];
extern const struct nla_policy ethnl_header_policy_stats[ETHTOOL_A_HEADER_FLAGS + 1];
+extern const struct nla_policy ethnl_header_policy_phy[ETHTOOL_A_HEADER_PHY_INDEX + 1];
+extern const struct nla_policy ethnl_header_policy_phy_stats[ETHTOOL_A_HEADER_PHY_INDEX + 1];
extern const struct nla_policy ethnl_strset_get_policy[ETHTOOL_A_STRSET_COUNTS_ONLY + 1];
extern const struct nla_policy ethnl_linkinfo_get_policy[ETHTOOL_A_LINKINFO_HEADER + 1];
extern const struct nla_policy ethnl_linkinfo_set_policy[ETHTOOL_A_LINKINFO_TP_MDIX_CTRL + 1];
--
2.43.0
Update the spec to take the newly introduced phy-index as a generic
request parameter.
Signed-off-by: Maxime Chevallier <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
---
V6: No changes
V5: Added Andrew's R-b
V4: Ditch the ethtool-user generated code
V3: New patch
Documentation/netlink/specs/ethtool.yaml | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/netlink/specs/ethtool.yaml b/Documentation/netlink/specs/ethtool.yaml
index 197208f419dc..bb6e1dc6d1c5 100644
--- a/Documentation/netlink/specs/ethtool.yaml
+++ b/Documentation/netlink/specs/ethtool.yaml
@@ -30,6 +30,9 @@ attribute-sets:
-
name: flags
type: u32
+ -
+ name: phy-index
+ type: u32
-
name: bitset-bit
--
2.43.0
The PHY_GET command, supporting both DUMP and GET operations, is used to
retrieve the list of PHYs connected to a netdevice, and get topology
information to know where exactly it sits on the physical link.
Add the netlink specs corresponding to that command.
Signed-off-by: Maxime Chevallier <[email protected]>
---
V6: Updated the spec according to the new attributes
V5: No changes
V4: Remove the ethtool-user generated code
V3: New patch
Documentation/netlink/specs/ethtool.yaml | 59 ++++++++++++++++++++++++
1 file changed, 59 insertions(+)
diff --git a/Documentation/netlink/specs/ethtool.yaml b/Documentation/netlink/specs/ethtool.yaml
index bb6e1dc6d1c5..e98d78fbc2f3 100644
--- a/Documentation/netlink/specs/ethtool.yaml
+++ b/Documentation/netlink/specs/ethtool.yaml
@@ -16,6 +16,11 @@ definitions:
name: stringset
type: enum
entries: []
+ -
+ name: phy-upstream-type
+ enum-name:
+ type: enum
+ entries: [ mac, phy ]
attribute-sets:
-
@@ -945,6 +950,38 @@ attribute-sets:
-
name: burst-tmr
type: u32
+ -
+ name: phy
+ attributes:
+ -
+ name: header
+ type: nest
+ nested-attributes: header
+ -
+ name: index
+ type: u32
+ -
+ name: drvname
+ type: string
+ -
+ name: name
+ type: string
+ -
+ name: upstream-type
+ type: u32
+ enum: phy-upstream-type
+ -
+ name: upstream-phy-index
+ type: u32
+ -
+ name: upstream-sfp-name
+ type: string
+ -
+ name: downstream-sfp-name
+ type: string
+ -
+ name: id
+ type: u32
operations:
enum-model: directional
@@ -1696,3 +1733,25 @@ operations:
name: mm-ntf
doc: Notification for change in MAC Merge configuration.
notify: mm-get
+ -
+ name: phy-get
+ doc: Get PHY devices attached to an interface
+
+ attribute-set: phy
+
+ do: &phy-get-op
+ request:
+ attributes:
+ - header
+ reply:
+ attributes:
+ - header
+ - index
+ - drvname
+ - name
+ - upstream-type
+ - upstream-phy-index
+ - upstream-sfp-name
+ - downstream-sfp-name
+ - id
+ dump: *phy-get-op
--
2.43.0
Knowing the bus name is helpful when we want to expose the link topology
to userspace, add a helper to return the SFP bus name.
Signed-off-by: Maxime Chevallier <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
---
V6: - No changes
V5: - Added Andrew's R-b
V4: - No changes
V3: - Added RTNL assert
- Made the stub inline
V2: New patch
drivers/net/phy/sfp-bus.c | 11 +++++++++++
include/linux/sfp.h | 6 ++++++
2 files changed, 17 insertions(+)
diff --git a/drivers/net/phy/sfp-bus.c b/drivers/net/phy/sfp-bus.c
index e05013aeecc3..413021619afe 100644
--- a/drivers/net/phy/sfp-bus.c
+++ b/drivers/net/phy/sfp-bus.c
@@ -859,3 +859,14 @@ void sfp_unregister_socket(struct sfp_bus *bus)
sfp_bus_put(bus);
}
EXPORT_SYMBOL_GPL(sfp_unregister_socket);
+
+const char *sfp_get_name(struct sfp_bus *bus)
+{
+ ASSERT_RTNL();
+
+ if (bus->sfp_dev)
+ return dev_name(bus->sfp_dev);
+
+ return NULL;
+}
+EXPORT_SYMBOL_GPL(sfp_get_name);
diff --git a/include/linux/sfp.h b/include/linux/sfp.h
index 0573e53b0c11..55c0ab17c9e2 100644
--- a/include/linux/sfp.h
+++ b/include/linux/sfp.h
@@ -570,6 +570,7 @@ struct sfp_bus *sfp_bus_find_fwnode(const struct fwnode_handle *fwnode);
int sfp_bus_add_upstream(struct sfp_bus *bus, void *upstream,
const struct sfp_upstream_ops *ops);
void sfp_bus_del_upstream(struct sfp_bus *bus);
+const char *sfp_get_name(struct sfp_bus *bus);
#else
static inline int sfp_parse_port(struct sfp_bus *bus,
const struct sfp_eeprom_id *id,
@@ -648,6 +649,11 @@ static inline int sfp_bus_add_upstream(struct sfp_bus *bus, void *upstream,
static inline void sfp_bus_del_upstream(struct sfp_bus *bus)
{
}
+
+static inline const char *sfp_get_name(struct sfp_bus *bus)
+{
+ return NULL;
+}
#endif
#endif
--
2.43.0
As we have the ability to track the PHYs connected to a net_device
through the link_topology, we can expose this list to userspace. This
allows userspace to use these identifiers for phy-specific commands and
take the decision of which PHY to target by knowing the link topology.
Add PHY_GET and PHY_DUMP, which can be a filtered DUMP operation to list
devices on only one interface.
Signed-off-by: Maxime Chevallier <[email protected]>
---
V6: - Removed un-needed nest
- Fixed the DUMP code
- Fixed the documentation formatting
V5: - Fixed xmas tree
- Fixed uninitialized return variable (Simon)
V4: - Fixed errors when not having SFP enabled, resulting in null names
being passed as parameters to strlen.
V3: - Fixed the documentation
- Fixed the DUMP implementation
V2: New patch
Documentation/networking/ethtool-netlink.rst | 39 +++
include/uapi/linux/ethtool_netlink.h | 20 ++
net/ethtool/Makefile | 2 +-
net/ethtool/netlink.c | 9 +
net/ethtool/netlink.h | 5 +
net/ethtool/phy.c | 298 +++++++++++++++++++
6 files changed, 372 insertions(+), 1 deletion(-)
create mode 100644 net/ethtool/phy.c
diff --git a/Documentation/networking/ethtool-netlink.rst b/Documentation/networking/ethtool-netlink.rst
index 3ca6c21e74af..e498c3b0b28f 100644
--- a/Documentation/networking/ethtool-netlink.rst
+++ b/Documentation/networking/ethtool-netlink.rst
@@ -2011,6 +2011,44 @@ The attributes are propagated to the driver through the following structure:
.. kernel-doc:: include/linux/ethtool.h
:identifiers: ethtool_mm_cfg
+PHY_GET
+=======
+
+Retrieve information about a given Ethernet PHY sitting on the link. As there
+can be more than one PHY, the DUMP operation can be used to list the PHYs
+present on a given interface, by passing an interface index or name in
+the dump request
+
+Request contents:
+
+ ==================================== ====== ==========================
+ ``ETHTOOL_A_PHY_HEADER`` nested request header
+ ==================================== ====== ==========================
+
+Kernel response contents:
+
+ ===================================== ====== ===============================
+ ``ETHTOOL_A_PHY_HEADER`` nested request header
+ ``ETHTOOL_A_PHY_INDEX`` u32 the phy's unique index, that can
+ be used for phy-specific
+ requests
+ ``ETHTOOL_A_PHY_DRVNAME`` string the phy driver name
+ ``ETHTOOL_A_PHY_NAME`` string the phy device name
+ ``ETHTOOL_A_PHY_UPSTREAM_TYPE`` u32 the type of device this phy is
+ connected to
+ ``ETHTOOL_A_PHY_UPSTREAM_INDEX`` u32 the PHY index of the upstream
+ PHY
+ ``ETHTOOL_A_PHY_UPSTREAM_SFP_NAME`` string if this PHY is connected to
+ it's parent PHY through an SFP
+ bus, the name of this sfp bus
+ ``ETHTOOL_A_PHY_DOWNSTREAM_SFP_NAME`` string if the phy controls an sfp bus,
+ the name of the sfp bus
+ ``ETHTOOL_A_PHY_ID`` u32 the phy id if the phy is C22
+ ===================================== ====== ===============================
+
+When ``ETHTOOL_A_PHY_UPSTREAM_TYPE`` is PHY_UPSTREAM_PHY, the PHY's parent is
+another PHY.
+
Request translation
===================
@@ -2117,4 +2155,5 @@ are netlink only.
n/a ``ETHTOOL_MSG_PLCA_GET_STATUS``
n/a ``ETHTOOL_MSG_MM_GET``
n/a ``ETHTOOL_MSG_MM_SET``
+ n/a ``ETHTOOL_MSG_PHY_GET``
=================================== =====================================
diff --git a/include/uapi/linux/ethtool_netlink.h b/include/uapi/linux/ethtool_netlink.h
index 422e8cfdd98c..f7a13e93ecb7 100644
--- a/include/uapi/linux/ethtool_netlink.h
+++ b/include/uapi/linux/ethtool_netlink.h
@@ -57,6 +57,7 @@ enum {
ETHTOOL_MSG_PLCA_GET_STATUS,
ETHTOOL_MSG_MM_GET,
ETHTOOL_MSG_MM_SET,
+ ETHTOOL_MSG_PHY_GET,
/* add new constants above here */
__ETHTOOL_MSG_USER_CNT,
@@ -109,6 +110,8 @@ enum {
ETHTOOL_MSG_PLCA_NTF,
ETHTOOL_MSG_MM_GET_REPLY,
ETHTOOL_MSG_MM_NTF,
+ ETHTOOL_MSG_PHY_GET_REPLY,
+ ETHTOOL_MSG_PHY_NTF,
/* add new constants above here */
__ETHTOOL_MSG_KERNEL_CNT,
@@ -977,6 +980,23 @@ enum {
ETHTOOL_A_MM_MAX = (__ETHTOOL_A_MM_CNT - 1)
};
+enum {
+ ETHTOOL_A_PHY_UNSPEC,
+ ETHTOOL_A_PHY_HEADER, /* nest - _A_HEADER_* */
+ ETHTOOL_A_PHY_INDEX, /* u32 */
+ ETHTOOL_A_PHY_DRVNAME, /* string */
+ ETHTOOL_A_PHY_NAME, /* string */
+ ETHTOOL_A_PHY_UPSTREAM_TYPE, /* u32 */
+ ETHTOOL_A_PHY_UPSTREAM_INDEX, /* u32 */
+ ETHTOOL_A_PHY_UPSTREAM_SFP_NAME, /* string */
+ ETHTOOL_A_PHY_DOWNSTREAM_SFP_NAME, /* string */
+ ETHTOOL_A_PHY_ID, /* u32 */
+
+ /* add new constants above here */
+ __ETHTOOL_A_PHY_CNT,
+ ETHTOOL_A_PHY_MAX = (__ETHTOOL_A_PHY_CNT - 1)
+};
+
/* generic netlink info */
#define ETHTOOL_GENL_NAME "ethtool"
#define ETHTOOL_GENL_VERSION 1
diff --git a/net/ethtool/Makefile b/net/ethtool/Makefile
index 504f954a1b28..0ccd0e9afd3f 100644
--- a/net/ethtool/Makefile
+++ b/net/ethtool/Makefile
@@ -8,4 +8,4 @@ ethtool_nl-y := netlink.o bitset.o strset.o linkinfo.o linkmodes.o rss.o \
linkstate.o debug.o wol.o features.o privflags.o rings.o \
channels.o coalesce.o pause.o eee.o tsinfo.o cabletest.o \
tunnels.o fec.o eeprom.o stats.o phc_vclocks.o mm.o \
- module.o pse-pd.o plca.o mm.o
+ module.o pse-pd.o plca.o mm.o phy.o
diff --git a/net/ethtool/netlink.c b/net/ethtool/netlink.c
index 5a9beb09e5d4..6334e8ce95f7 100644
--- a/net/ethtool/netlink.c
+++ b/net/ethtool/netlink.c
@@ -1169,6 +1169,15 @@ static const struct genl_ops ethtool_genl_ops[] = {
.policy = ethnl_mm_set_policy,
.maxattr = ARRAY_SIZE(ethnl_mm_set_policy) - 1,
},
+ {
+ .cmd = ETHTOOL_MSG_PHY_GET,
+ .doit = ethnl_phy_doit,
+ .start = ethnl_phy_start,
+ .dumpit = ethnl_phy_dumpit,
+ .done = ethnl_phy_done,
+ .policy = ethnl_phy_get_policy,
+ .maxattr = ARRAY_SIZE(ethnl_phy_get_policy) - 1,
+ },
};
static const struct genl_multicast_group ethtool_nl_mcgrps[] = {
diff --git a/net/ethtool/netlink.h b/net/ethtool/netlink.h
index d57a890b5d9e..0e71b53bdb1c 100644
--- a/net/ethtool/netlink.h
+++ b/net/ethtool/netlink.h
@@ -446,6 +446,7 @@ extern const struct nla_policy ethnl_plca_set_cfg_policy[ETHTOOL_A_PLCA_MAX + 1]
extern const struct nla_policy ethnl_plca_get_status_policy[ETHTOOL_A_PLCA_HEADER + 1];
extern const struct nla_policy ethnl_mm_get_policy[ETHTOOL_A_MM_HEADER + 1];
extern const struct nla_policy ethnl_mm_set_policy[ETHTOOL_A_MM_MAX + 1];
+extern const struct nla_policy ethnl_phy_get_policy[ETHTOOL_A_PHY_HEADER + 1];
int ethnl_set_features(struct sk_buff *skb, struct genl_info *info);
int ethnl_act_cable_test(struct sk_buff *skb, struct genl_info *info);
@@ -453,6 +454,10 @@ int ethnl_act_cable_test_tdr(struct sk_buff *skb, struct genl_info *info);
int ethnl_tunnel_info_doit(struct sk_buff *skb, struct genl_info *info);
int ethnl_tunnel_info_start(struct netlink_callback *cb);
int ethnl_tunnel_info_dumpit(struct sk_buff *skb, struct netlink_callback *cb);
+int ethnl_phy_start(struct netlink_callback *cb);
+int ethnl_phy_doit(struct sk_buff *skb, struct genl_info *info);
+int ethnl_phy_dumpit(struct sk_buff *skb, struct netlink_callback *cb);
+int ethnl_phy_done(struct netlink_callback *cb);
extern const char stats_std_names[__ETHTOOL_STATS_CNT][ETH_GSTRING_LEN];
extern const char stats_eth_phy_names[__ETHTOOL_A_STATS_ETH_PHY_CNT][ETH_GSTRING_LEN];
diff --git a/net/ethtool/phy.c b/net/ethtool/phy.c
new file mode 100644
index 000000000000..116a60a2b1be
--- /dev/null
+++ b/net/ethtool/phy.c
@@ -0,0 +1,298 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2023 Bootlin
+ *
+ */
+#include "common.h"
+#include "netlink.h"
+
+#include <linux/phy.h>
+#include <linux/phy_link_topology.h>
+#include <linux/sfp.h>
+
+struct phy_req_info {
+ struct ethnl_req_info base;
+ struct phy_device_node pdn;
+};
+
+#define PHY_REQINFO(__req_base) \
+ container_of(__req_base, struct phy_req_info, base)
+
+const struct nla_policy ethnl_phy_get_policy[ETHTOOL_A_PHY_HEADER + 1] = {
+ [ETHTOOL_A_PHY_HEADER] = NLA_POLICY_NESTED(ethnl_header_policy),
+};
+
+/* Caller holds rtnl */
+static ssize_t
+ethnl_phy_reply_size(const struct ethnl_req_info *req_base,
+ struct netlink_ext_ack *extack)
+{
+ struct phy_req_info *req_info = PHY_REQINFO(req_base);
+ struct phy_device_node *pdn = &req_info->pdn;
+ struct phy_device *phydev = pdn->phy;
+ size_t size = 0;
+
+ ASSERT_RTNL();
+
+ /* ETHTOOL_A_PHY_INDEX */
+ size += nla_total_size(sizeof(u32));
+
+ /* ETHTOOL_A_DRVNAME */
+ if (phydev->drv)
+ size += nla_total_size(strlen(phydev->drv->name) + 1);
+
+ /* ETHTOOL_A_NAME */
+ size += nla_total_size(strlen(dev_name(&phydev->mdio.dev)) + 1);
+
+ /* ETHTOOL_A_PHY_UPSTREAM_TYPE */
+ size += nla_total_size(sizeof(u32));
+
+ /* ETHTOOL_A_PHY_ID */
+ size += nla_total_size(sizeof(u32));
+
+ if (phy_on_sfp(phydev)) {
+ const char *upstream_sfp_name = sfp_get_name(pdn->parent_sfp_bus);
+
+ /* ETHTOOL_A_PHY_UPSTREAM_SFP_NAME */
+ if (upstream_sfp_name)
+ size += nla_total_size(strlen(upstream_sfp_name) + 1);
+
+ /* ETHTOOL_A_PHY_UPSTREAM_INDEX */
+ size += nla_total_size(sizeof(u32));
+ }
+
+ /* ETHTOOL_A_PHY_DOWNSTREAM_SFP_NAME */
+ if (phydev->sfp_bus) {
+ const char *sfp_name = sfp_get_name(phydev->sfp_bus);
+
+ if (sfp_name)
+ size += nla_total_size(strlen(sfp_name) + 1);
+ }
+
+ return size;
+}
+
+static int
+ethnl_phy_fill_reply(const struct ethnl_req_info *req_base, struct sk_buff *skb)
+{
+ struct phy_req_info *req_info = PHY_REQINFO(req_base);
+ struct phy_device_node *pdn = &req_info->pdn;
+ struct phy_device *phydev = pdn->phy;
+ enum phy_upstream ptype;
+
+ ptype = pdn->upstream_type;
+
+ if (nla_put_u32(skb, ETHTOOL_A_PHY_INDEX, phydev->phyindex) ||
+ nla_put_string(skb, ETHTOOL_A_PHY_NAME, dev_name(&phydev->mdio.dev)) ||
+ nla_put_u32(skb, ETHTOOL_A_PHY_UPSTREAM_TYPE, ptype) ||
+ nla_put_u32(skb, ETHTOOL_A_PHY_ID, phydev->phy_id))
+ return -EMSGSIZE;
+
+ if (phydev->drv && nla_put_string(skb, ETHTOOL_A_PHY_DRVNAME, phydev->drv->name))
+ return -EMSGSIZE;
+
+ if (ptype == PHY_UPSTREAM_PHY) {
+ struct phy_device *upstream = pdn->upstream.phydev;
+ const char *sfp_upstream_name;
+
+ /* Parent index */
+ if (nla_put_u32(skb, ETHTOOL_A_PHY_UPSTREAM_INDEX, upstream->phyindex))
+ return -EMSGSIZE;
+
+ if (pdn->parent_sfp_bus) {
+ sfp_upstream_name = sfp_get_name(pdn->parent_sfp_bus);
+ if (sfp_upstream_name && nla_put_string(skb,
+ ETHTOOL_A_PHY_UPSTREAM_SFP_NAME,
+ sfp_upstream_name))
+ return -EMSGSIZE;
+ }
+ }
+
+ if (phydev->sfp_bus) {
+ const char *sfp_name = sfp_get_name(phydev->sfp_bus);
+
+ if (sfp_name &&
+ nla_put_string(skb, ETHTOOL_A_PHY_DOWNSTREAM_SFP_NAME,
+ sfp_name))
+ return -EMSGSIZE;
+ }
+
+ return 0;
+}
+
+static int ethnl_phy_parse_request(struct ethnl_req_info *req_base,
+ struct nlattr **tb)
+{
+ struct phy_link_topology *topo = req_base->dev->link_topo;
+ struct phy_req_info *req_info = PHY_REQINFO(req_base);
+ struct phy_device_node *pdn;
+
+ if (!req_base->phydev)
+ return 0;
+
+ pdn = xa_load(&topo->phys, req_base->phydev->phyindex);
+ memcpy(&req_info->pdn, pdn, sizeof(*pdn));
+
+ return 0;
+}
+
+int ethnl_phy_doit(struct sk_buff *skb, struct genl_info *info)
+{
+ struct phy_req_info req_info = {};
+ struct nlattr **tb = info->attrs;
+ struct sk_buff *rskb;
+ void *reply_payload;
+ int reply_len;
+ int ret;
+
+ ret = ethnl_parse_header_dev_get(&req_info.base,
+ tb[ETHTOOL_A_PHY_HEADER],
+ genl_info_net(info), info->extack,
+ true);
+ if (ret < 0)
+ return ret;
+
+ rtnl_lock();
+
+ ret = ethnl_phy_parse_request(&req_info.base, tb);
+ if (ret < 0)
+ goto err_unlock_rtnl;
+
+ /* No PHY, return early */
+ if (!req_info.pdn.phy)
+ goto err_unlock_rtnl;
+
+ ret = ethnl_phy_reply_size(&req_info.base, info->extack);
+ if (ret < 0)
+ goto err_unlock_rtnl;
+ reply_len = ret + ethnl_reply_header_size();
+
+ rskb = ethnl_reply_init(reply_len, req_info.base.dev,
+ ETHTOOL_MSG_PHY_GET_REPLY,
+ ETHTOOL_A_PHY_HEADER,
+ info, &reply_payload);
+ if (!rskb) {
+ ret = -ENOMEM;
+ goto err_unlock_rtnl;
+ }
+
+ ret = ethnl_phy_fill_reply(&req_info.base, rskb);
+ if (ret)
+ goto err_free_msg;
+
+ rtnl_unlock();
+ ethnl_parse_header_dev_put(&req_info.base);
+ genlmsg_end(rskb, reply_payload);
+
+ return genlmsg_reply(rskb, info);
+
+err_free_msg:
+ nlmsg_free(rskb);
+err_unlock_rtnl:
+ rtnl_unlock();
+ ethnl_parse_header_dev_put(&req_info.base);
+ return ret;
+}
+
+struct ethnl_phy_dump_ctx {
+ struct phy_req_info *phy_req_info;
+ unsigned long ifindex;
+ unsigned long phy_index;
+};
+
+int ethnl_phy_start(struct netlink_callback *cb)
+{
+ const struct genl_dumpit_info *info = genl_dumpit_info(cb);
+ struct ethnl_phy_dump_ctx *ctx = (void *)cb->ctx;
+ struct nlattr **tb = info->info.attrs;
+ int ret;
+
+ BUILD_BUG_ON(sizeof(*ctx) > sizeof(cb->ctx));
+
+ ctx->phy_req_info = kzalloc(sizeof(*ctx->phy_req_info), GFP_KERNEL);
+ if (!ctx->phy_req_info)
+ return -ENOMEM;
+
+ ret = ethnl_parse_header_dev_get(&ctx->phy_req_info->base,
+ tb[ETHTOOL_A_PHY_HEADER],
+ sock_net(cb->skb->sk), cb->extack,
+ false);
+ ctx->ifindex = 0;
+ ctx->phy_index = 0;
+ return ret;
+}
+
+int ethnl_phy_done(struct netlink_callback *cb)
+{
+ struct ethnl_phy_dump_ctx *ctx = (void *)cb->ctx;
+
+ kfree(ctx->phy_req_info);
+
+ return 0;
+}
+
+static int ethnl_phy_dump_one_dev(struct sk_buff *skb, struct net_device *dev,
+ struct netlink_callback *cb)
+{
+ struct ethnl_phy_dump_ctx *ctx = (void *)cb->ctx;
+ struct phy_req_info *pri = ctx->phy_req_info;
+ struct phy_device_node *pdn;
+ int ret = 0;
+ void *ehdr;
+
+ pri->base.dev = dev;
+
+ xa_for_each_start(&dev->link_topo->phys, ctx->phy_index, pdn, ctx->phy_index) {
+ ehdr = ethnl_dump_put(skb, cb,
+ ETHTOOL_MSG_PHY_GET_REPLY);
+ if (!ehdr) {
+ ret = -EMSGSIZE;
+ break;
+ }
+
+ ret = ethnl_fill_reply_header(skb, dev,
+ ETHTOOL_A_PHY_HEADER);
+ if (ret < 0) {
+ genlmsg_cancel(skb, ehdr);
+ break;
+ }
+
+ memcpy(&pri->pdn, pdn, sizeof(*pdn));
+ ret = ethnl_phy_fill_reply(&pri->base, skb);
+
+ genlmsg_end(skb, ehdr);
+ }
+
+ return ret;
+}
+
+int ethnl_phy_dumpit(struct sk_buff *skb, struct netlink_callback *cb)
+{
+ struct ethnl_phy_dump_ctx *ctx = (void *)cb->ctx;
+ struct net *net = sock_net(skb->sk);
+ struct net_device *dev;
+ int ret = 0;
+
+ rtnl_lock();
+
+ if (ctx->phy_req_info->base.dev) {
+ ret = ethnl_phy_dump_one_dev(skb, ctx->phy_req_info->base.dev, cb);
+ ethnl_parse_header_dev_put(&ctx->phy_req_info->base);
+ ctx->phy_req_info->base.dev = NULL;
+ } else {
+ for_each_netdev_dump(net, dev, ctx->ifindex) {
+ ret = ethnl_phy_dump_one_dev(skb, dev, cb);
+ if (ret)
+ break;
+
+ ctx->phy_index = 0;
+ }
+ }
+ rtnl_unlock();
+
+ if (ret == -EMSGSIZE && skb->len)
+ return skb->len;
+
+ return ret;
+}
+
--
2.43.0
There are a few PHY drivers that can handle SFP modules through their
sfp_upstream_ops. Introduce Phylib helpers to keep track of connected
SFP PHYs in a netdevice's namespace, by adding the SFP PHY to the
upstream PHY's netdev's namespace.
By doing so, these SFP PHYs can be enumerated and exposed to users,
which will be able to use their capabilities.
Signed-off-by: Maxime Chevallier <[email protected]>
---
V6: Moved phy_get_link_topology() definition to this patch
V5: No Changes
V4: Rebased the at803x part with the newer version on net-next
V3: Renaming
V2: Renaming
drivers/net/phy/at803x.c | 2 ++
drivers/net/phy/marvell-88x2222.c | 2 ++
drivers/net/phy/marvell.c | 2 ++
drivers/net/phy/marvell10g.c | 2 ++
drivers/net/phy/phy_device.c | 48 +++++++++++++++++++++++++++++++
include/linux/phy.h | 2 ++
6 files changed, 58 insertions(+)
diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index a62442a55774..2f50170738f3 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -1475,6 +1475,8 @@ static const struct sfp_upstream_ops at8031_sfp_ops = {
.attach = phy_sfp_attach,
.detach = phy_sfp_detach,
.module_insert = at8031_sfp_insert,
+ .connect_phy = phy_sfp_connect_phy,
+ .disconnect_phy = phy_sfp_disconnect_phy,
};
static int at8031_parse_dt(struct phy_device *phydev)
diff --git a/drivers/net/phy/marvell-88x2222.c b/drivers/net/phy/marvell-88x2222.c
index e3aa30dad2e6..3f77bbc7e04f 100644
--- a/drivers/net/phy/marvell-88x2222.c
+++ b/drivers/net/phy/marvell-88x2222.c
@@ -555,6 +555,8 @@ static const struct sfp_upstream_ops sfp_phy_ops = {
.link_down = mv2222_sfp_link_down,
.attach = phy_sfp_attach,
.detach = phy_sfp_detach,
+ .connect_phy = phy_sfp_connect_phy,
+ .disconnect_phy = phy_sfp_disconnect_phy,
};
static int mv2222_probe(struct phy_device *phydev)
diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
index eba652a4c1d8..674e29bce2cc 100644
--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -3254,6 +3254,8 @@ static const struct sfp_upstream_ops m88e1510_sfp_ops = {
.module_remove = m88e1510_sfp_remove,
.attach = phy_sfp_attach,
.detach = phy_sfp_detach,
+ .connect_phy = phy_sfp_connect_phy,
+ .disconnect_phy = phy_sfp_disconnect_phy,
};
static int m88e1510_probe(struct phy_device *phydev)
diff --git a/drivers/net/phy/marvell10g.c b/drivers/net/phy/marvell10g.c
index ad43e280930c..6642eb642d4b 100644
--- a/drivers/net/phy/marvell10g.c
+++ b/drivers/net/phy/marvell10g.c
@@ -503,6 +503,8 @@ static int mv3310_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
static const struct sfp_upstream_ops mv3310_sfp_ops = {
.attach = phy_sfp_attach,
.detach = phy_sfp_detach,
+ .connect_phy = phy_sfp_connect_phy,
+ .disconnect_phy = phy_sfp_disconnect_phy,
.module_insert = mv3310_sfp_insert,
};
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 9385a4ee9380..436c7b62d5be 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -266,6 +266,14 @@ static void phy_mdio_device_remove(struct mdio_device *mdiodev)
static struct phy_driver genphy_driver;
+static struct phy_link_topology *phy_get_link_topology(struct phy_device *phydev)
+{
+ if (phydev->attached_dev)
+ return phydev->attached_dev->link_topo;
+
+ return NULL;
+}
+
static LIST_HEAD(phy_fixup_list);
static DEFINE_MUTEX(phy_fixup_lock);
@@ -1355,6 +1363,46 @@ phy_standalone_show(struct device *dev, struct device_attribute *attr,
}
static DEVICE_ATTR_RO(phy_standalone);
+/**
+ * phy_sfp_connect_phy - Connect the SFP module's PHY to the upstream PHY
+ * @upstream: pointer to the upstream phy device
+ * @phy: pointer to the SFP module's phy device
+ *
+ * This helper allows keeping track of PHY devices on the link. It adds the
+ * SFP module's phy to the phy namespace of the upstream phy
+ */
+int phy_sfp_connect_phy(void *upstream, struct phy_device *phy)
+{
+ struct phy_device *phydev = upstream;
+ struct phy_link_topology *topo = phy_get_link_topology(phydev);
+
+ if (topo)
+ return phy_link_topo_add_phy(topo, phy, PHY_UPSTREAM_PHY, phydev);
+
+ return 0;
+}
+EXPORT_SYMBOL(phy_sfp_connect_phy);
+
+/**
+ * phy_sfp_disconnect_phy - Disconnect the SFP module's PHY from the upstream PHY
+ * @upstream: pointer to the upstream phy device
+ * @phy: pointer to the SFP module's phy device
+ *
+ * This helper allows keeping track of PHY devices on the link. It removes the
+ * SFP module's phy to the phy namespace of the upstream phy. As the module phy
+ * will be destroyed, re-inserting the same module will add a new phy with a
+ * new index.
+ */
+void phy_sfp_disconnect_phy(void *upstream, struct phy_device *phy)
+{
+ struct phy_device *phydev = upstream;
+ struct phy_link_topology *topo = phy_get_link_topology(phydev);
+
+ if (topo)
+ phy_link_topo_del_phy(topo, phy);
+}
+EXPORT_SYMBOL(phy_sfp_disconnect_phy);
+
/**
* phy_sfp_attach - attach the SFP bus to the PHY upstream network device
* @upstream: pointer to the phy device
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 78647b5e0c13..3637bdfc1166 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -1725,6 +1725,8 @@ int phy_suspend(struct phy_device *phydev);
int phy_resume(struct phy_device *phydev);
int __phy_resume(struct phy_device *phydev);
int phy_loopback(struct phy_device *phydev, bool enable);
+int phy_sfp_connect_phy(void *upstream, struct phy_device *phy);
+void phy_sfp_disconnect_phy(void *upstream, struct phy_device *phy);
void phy_sfp_attach(void *upstream, struct sfp_bus *bus);
void phy_sfp_detach(void *upstream, struct sfp_bus *bus);
int phy_sfp_probe(struct phy_device *phydev,
--
2.43.0
Cable testing is a PHY-specific command. Instead of targeting the command
towards dev->phydev, use the request to pick the targeted PHY.
Signed-off-by: Maxime Chevallier <[email protected]>
---
V6: Use dedicated policy
V5: Added Andrew's R-b
V4: No changes
V3: No changes
V2: New patch
net/ethtool/cabletest.c | 16 ++++++++--------
1 file changed, 8 insertions(+), 8 deletions(-)
diff --git a/net/ethtool/cabletest.c b/net/ethtool/cabletest.c
index 06a151165c31..536800bbc379 100644
--- a/net/ethtool/cabletest.c
+++ b/net/ethtool/cabletest.c
@@ -13,7 +13,7 @@
const struct nla_policy ethnl_cable_test_act_policy[] = {
[ETHTOOL_A_CABLE_TEST_HEADER] =
- NLA_POLICY_NESTED(ethnl_header_policy),
+ NLA_POLICY_NESTED(ethnl_header_policy_phy),
};
static int ethnl_cable_test_started(struct phy_device *phydev, u8 cmd)
@@ -69,7 +69,7 @@ int ethnl_act_cable_test(struct sk_buff *skb, struct genl_info *info)
return ret;
dev = req_info.dev;
- if (!dev->phydev) {
+ if (!req_info.phydev) {
ret = -EOPNOTSUPP;
goto out_dev_put;
}
@@ -85,12 +85,12 @@ int ethnl_act_cable_test(struct sk_buff *skb, struct genl_info *info)
if (ret < 0)
goto out_rtnl;
- ret = ops->start_cable_test(dev->phydev, info->extack);
+ ret = ops->start_cable_test(req_info.phydev, info->extack);
ethnl_ops_complete(dev);
if (!ret)
- ethnl_cable_test_started(dev->phydev,
+ ethnl_cable_test_started(req_info.phydev,
ETHTOOL_MSG_CABLE_TEST_NTF);
out_rtnl:
@@ -220,7 +220,7 @@ static const struct nla_policy cable_test_tdr_act_cfg_policy[] = {
const struct nla_policy ethnl_cable_test_tdr_act_policy[] = {
[ETHTOOL_A_CABLE_TEST_TDR_HEADER] =
- NLA_POLICY_NESTED(ethnl_header_policy),
+ NLA_POLICY_NESTED(ethnl_header_policy_phy),
[ETHTOOL_A_CABLE_TEST_TDR_CFG] = { .type = NLA_NESTED },
};
@@ -321,7 +321,7 @@ int ethnl_act_cable_test_tdr(struct sk_buff *skb, struct genl_info *info)
return ret;
dev = req_info.dev;
- if (!dev->phydev) {
+ if (!req_info.phydev) {
ret = -EOPNOTSUPP;
goto out_dev_put;
}
@@ -342,12 +342,12 @@ int ethnl_act_cable_test_tdr(struct sk_buff *skb, struct genl_info *info)
if (ret < 0)
goto out_rtnl;
- ret = ops->start_cable_test_tdr(dev->phydev, info->extack, &cfg);
+ ret = ops->start_cable_test_tdr(req_info.phydev, info->extack, &cfg);
ethnl_ops_complete(dev);
if (!ret)
- ethnl_cable_test_started(dev->phydev,
+ ethnl_cable_test_started(req_info.phydev,
ETHTOOL_MSG_CABLE_TEST_TDR_NTF);
out_rtnl:
--
2.43.0
The ETH_SS_PHY_STATS command gets PHY statistics. Use the phydev pointer
from the ethnl request to allow query phy stats from each PHY on the
link.
Signed-off-by: Maxime Chevallier <[email protected]>
---
V6: Use dedicated policy
V5: Added Andrew's R-b
V4: No changes
V3: No changes
V2: New patch
net/ethtool/strset.c | 17 +++++++++--------
1 file changed, 9 insertions(+), 8 deletions(-)
diff --git a/net/ethtool/strset.c b/net/ethtool/strset.c
index c678b484a079..edc826407564 100644
--- a/net/ethtool/strset.c
+++ b/net/ethtool/strset.c
@@ -126,7 +126,7 @@ struct strset_reply_data {
const struct nla_policy ethnl_strset_get_policy[] = {
[ETHTOOL_A_STRSET_HEADER] =
- NLA_POLICY_NESTED(ethnl_header_policy),
+ NLA_POLICY_NESTED(ethnl_header_policy_phy),
[ETHTOOL_A_STRSET_STRINGSETS] = { .type = NLA_NESTED },
[ETHTOOL_A_STRSET_COUNTS_ONLY] = { .type = NLA_FLAG },
};
@@ -233,17 +233,18 @@ static void strset_cleanup_data(struct ethnl_reply_data *reply_base)
}
static int strset_prepare_set(struct strset_info *info, struct net_device *dev,
- unsigned int id, bool counts_only)
+ struct phy_device *phydev, unsigned int id,
+ bool counts_only)
{
const struct ethtool_phy_ops *phy_ops = ethtool_phy_ops;
const struct ethtool_ops *ops = dev->ethtool_ops;
void *strings;
int count, ret;
- if (id == ETH_SS_PHY_STATS && dev->phydev &&
+ if (id == ETH_SS_PHY_STATS && phydev &&
!ops->get_ethtool_phy_stats && phy_ops &&
phy_ops->get_sset_count)
- ret = phy_ops->get_sset_count(dev->phydev);
+ ret = phy_ops->get_sset_count(phydev);
else if (ops->get_sset_count && ops->get_strings)
ret = ops->get_sset_count(dev, id);
else
@@ -258,10 +259,10 @@ static int strset_prepare_set(struct strset_info *info, struct net_device *dev,
strings = kcalloc(count, ETH_GSTRING_LEN, GFP_KERNEL);
if (!strings)
return -ENOMEM;
- if (id == ETH_SS_PHY_STATS && dev->phydev &&
+ if (id == ETH_SS_PHY_STATS && phydev &&
!ops->get_ethtool_phy_stats && phy_ops &&
phy_ops->get_strings)
- phy_ops->get_strings(dev->phydev, strings);
+ phy_ops->get_strings(phydev, strings);
else
ops->get_strings(dev, id, strings);
info->strings = strings;
@@ -305,8 +306,8 @@ static int strset_prepare_data(const struct ethnl_req_info *req_base,
!data->sets[i].per_dev)
continue;
- ret = strset_prepare_set(&data->sets[i], dev, i,
- req_info->counts_only);
+ ret = strset_prepare_set(&data->sets[i], dev, req_base->phydev,
+ i, req_info->counts_only);
if (ret < 0)
goto err_ops;
}
--
2.43.0
Link topologies containing multiple network PHYs attached to the same
net_device can be found when using a PHY as a media converter for use
with an SFP connector, on which an SFP transceiver containing a PHY can
be used.
With the current model, the transceiver's PHY can't be used for
operations such as cable testing, timestamping, macsec offload, etc.
The reason being that most of the logic for these configuration, coming
from either ethtool netlink or ioctls tend to use netdev->phydev, which
in multi-phy systems will reference the PHY closest to the MAC.
Introduce a numbering scheme allowing to enumerate PHY devices that
belong to any netdev, which can in turn allow userspace to take more
precise decisions with regard to each PHY's configuration.
The numbering is maintained per-netdev, in a phy_device_list.
The numbering works similarly to a netdevice's ifindex, with
identifiers that are only recycled once INT_MAX has been reached.
This prevents races that could occur between PHY listing and SFP
transceiver removal/insertion.
The identifiers are assigned at phy_attach time, as the numbering
depends on the netdevice the phy is attached to. The PHY index can be
re-used for PHYs that are persistent.
Signed-off-by: Maxime Chevallier <[email protected]>
---
V6: - Made link_topo a pointer
- Reworked the init/cleanup sequence
- Added phy_index recycling if possible
V5: - Dropped the ASSERT_RTNL()
- Made the phy_link_topo_get_phy inline
V4: - Moved the phy_link_topo_init() code to an inline header function
- Made the code build without phylib
V3: - Renamed to phy_link_topology
- Added assertions for RTNL
- Various cleanups of leftover, unused test code
- Made the PHY index u32
MAINTAINERS | 2 +
drivers/net/phy/Makefile | 2 +-
drivers/net/phy/phy_device.c | 7 ++
drivers/net/phy/phy_link_topology.c | 105 +++++++++++++++++++++++++
include/linux/netdevice.h | 4 +-
include/linux/phy.h | 4 +
include/linux/phy_link_topology.h | 72 +++++++++++++++++
include/linux/phy_link_topology_core.h | 25 ++++++
include/uapi/linux/ethtool.h | 16 ++++
net/core/dev.c | 9 +++
10 files changed, 244 insertions(+), 2 deletions(-)
create mode 100644 drivers/net/phy/phy_link_topology.c
create mode 100644 include/linux/phy_link_topology.h
create mode 100644 include/linux/phy_link_topology_core.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 92152ac346c8..d61b1e6dcd1b 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7939,6 +7939,8 @@ F: include/linux/mii.h
F: include/linux/of_net.h
F: include/linux/phy.h
F: include/linux/phy_fixed.h
+F: include/linux/phy_link_topology.h
+F: include/linux/phy_link_topology_core.h
F: include/linux/phylib_stubs.h
F: include/linux/platform_data/mdio-bcm-unimac.h
F: include/linux/platform_data/mdio-gpio.h
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index 6097afd44392..f218954fd7a8 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -2,7 +2,7 @@
# Makefile for Linux PHY drivers
libphy-y := phy.o phy-c45.o phy-core.o phy_device.o \
- linkmode.o
+ linkmode.o phy_link_topology.o
mdio-bus-y += mdio_bus.o mdio_device.o
ifdef CONFIG_MDIO_DEVICE
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 3611ea64875e..9385a4ee9380 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -29,6 +29,7 @@
#include <linux/phy.h>
#include <linux/phylib_stubs.h>
#include <linux/phy_led_triggers.h>
+#include <linux/phy_link_topology.h>
#include <linux/pse-pd/pse.h>
#include <linux/property.h>
#include <linux/rtnetlink.h>
@@ -1491,6 +1492,11 @@ int phy_attach_direct(struct net_device *dev, struct phy_device *phydev,
if (phydev->sfp_bus_attached)
dev->sfp_bus = phydev->sfp_bus;
+
+ err = phy_link_topo_add_phy(dev->link_topo, phydev,
+ PHY_UPSTREAM_MAC, dev);
+ if (err)
+ goto error;
}
/* Some Ethernet drivers try to connect to a PHY device before
@@ -1820,6 +1826,7 @@ void phy_detach(struct phy_device *phydev)
if (dev) {
phydev->attached_dev->phydev = NULL;
phydev->attached_dev = NULL;
+ phy_link_topo_del_phy(dev->link_topo, phydev);
}
phydev->phylink = NULL;
diff --git a/drivers/net/phy/phy_link_topology.c b/drivers/net/phy/phy_link_topology.c
new file mode 100644
index 000000000000..985941c5c558
--- /dev/null
+++ b/drivers/net/phy/phy_link_topology.c
@@ -0,0 +1,105 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Infrastructure to handle all PHY devices connected to a given netdev,
+ * either directly or indirectly attached.
+ *
+ * Copyright (c) 2023 Maxime Chevallier<[email protected]>
+ */
+
+#include <linux/phy_link_topology.h>
+#include <linux/netdevice.h>
+#include <linux/phy.h>
+#include <linux/rtnetlink.h>
+#include <linux/xarray.h>
+
+struct phy_link_topology *phy_link_topo_create(struct net_device *dev)
+{
+ struct phy_link_topology *topo;
+
+ topo = kzalloc(sizeof(*topo), GFP_KERNEL);
+ if (!topo)
+ return ERR_PTR(-ENOMEM);
+
+ xa_init_flags(&topo->phys, XA_FLAGS_ALLOC1);
+ topo->next_phy_index = 1;
+
+ return topo;
+}
+
+void phy_link_topo_destroy(struct phy_link_topology *topo)
+{
+ if (!topo)
+ return;
+
+ xa_destroy(&topo->phys);
+ kfree(topo);
+}
+
+int phy_link_topo_add_phy(struct phy_link_topology *topo,
+ struct phy_device *phy,
+ enum phy_upstream upt, void *upstream)
+{
+ struct phy_device_node *pdn;
+ int ret;
+
+ pdn = kzalloc(sizeof(*pdn), GFP_KERNEL);
+ if (!pdn)
+ return -ENOMEM;
+
+ pdn->phy = phy;
+ switch (upt) {
+ case PHY_UPSTREAM_MAC:
+ pdn->upstream.netdev = (struct net_device *)upstream;
+ if (phy_on_sfp(phy))
+ pdn->parent_sfp_bus = pdn->upstream.netdev->sfp_bus;
+ break;
+ case PHY_UPSTREAM_PHY:
+ pdn->upstream.phydev = (struct phy_device *)upstream;
+ if (phy_on_sfp(phy))
+ pdn->parent_sfp_bus = pdn->upstream.phydev->sfp_bus;
+ break;
+ default:
+ ret = -EINVAL;
+ goto err;
+ }
+ pdn->upstream_type = upt;
+
+ /* Attempt to re-use a previously allocated phy_index */
+ if (phy->phyindex) {
+ ret = xa_insert(&topo->phys, phy->phyindex, pdn, GFP_KERNEL);
+
+ /* Errors could be either -ENOMEM or -EBUSY. If the phy has an
+ * index, and there's another entry at the same index, this is
+ * unexpected and we still error-out
+ */
+ if (ret)
+ goto err;
+ return 0;
+ }
+
+ ret = xa_alloc_cyclic(&topo->phys, &phy->phyindex, pdn, xa_limit_32b,
+ &topo->next_phy_index, GFP_KERNEL);
+ if (ret)
+ goto err;
+
+ return 0;
+
+err:
+ kfree(pdn);
+ return ret;
+}
+EXPORT_SYMBOL_GPL(phy_link_topo_add_phy);
+
+void phy_link_topo_del_phy(struct phy_link_topology *topo,
+ struct phy_device *phy)
+{
+ struct phy_device_node *pdn = xa_erase(&topo->phys, phy->phyindex);
+
+ /* We delete the PHY from the topology, however we don't re-set the
+ * phy->phyindex field. If the PHY isn't gone, we can re-assign it the
+ * same index next time it's added back to the topology
+ */
+
+ kfree(pdn);
+}
+EXPORT_SYMBOL_GPL(phy_link_topo_del_phy);
diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h
index 118c40258d07..eef604c4df81 100644
--- a/include/linux/netdevice.h
+++ b/include/linux/netdevice.h
@@ -40,7 +40,6 @@
#include <net/dcbnl.h>
#endif
#include <net/netprio_cgroup.h>
-
#include <linux/netdev_features.h>
#include <linux/neighbour.h>
#include <uapi/linux/netdevice.h>
@@ -52,6 +51,7 @@
#include <net/net_trackers.h>
#include <net/net_debug.h>
#include <net/dropreason-core.h>
+#include <linux/phy_link_topology_core.h>
struct netpoll_info;
struct device;
@@ -2047,6 +2047,7 @@ enum netdev_stat_type {
* @fcoe_ddp_xid: Max exchange id for FCoE LRO by ddp
*
* @priomap: XXX: need comments on this one
+ * @link_topo: Physical link topology tracking attached PHYs
* @phydev: Physical device may attach itself
* for hardware timestamping
* @sfp_bus: attached &struct sfp_bus structure.
@@ -2441,6 +2442,7 @@ struct net_device {
#if IS_ENABLED(CONFIG_CGROUP_NET_PRIO)
struct netprio_map __rcu *priomap;
#endif
+ struct phy_link_topology *link_topo;
struct phy_device *phydev;
struct sfp_bus *sfp_bus;
struct lock_class_key *qdisc_tx_busylock;
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 684efaeca07c..78647b5e0c13 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -544,6 +544,9 @@ struct macsec_ops;
* @drv: Pointer to the driver for this PHY instance
* @devlink: Create a link between phy dev and mac dev, if the external phy
* used by current mac interface is managed by another mac interface.
+ * @phyindex: Unique id across the phy's parent tree of phys to address the PHY
+ * from userspace, similar to ifindex. A zero index means the PHY
+ * wasn't assigned an id yet.
* @phy_id: UID for this device found during discovery
* @c45_ids: 802.3-c45 Device Identifiers if is_c45.
* @is_c45: Set to true if this PHY uses clause 45 addressing.
@@ -642,6 +645,7 @@ struct phy_device {
struct device_link *devlink;
+ u32 phyindex;
u32 phy_id;
struct phy_c45_device_ids c45_ids;
diff --git a/include/linux/phy_link_topology.h b/include/linux/phy_link_topology.h
new file mode 100644
index 000000000000..fdc630a4637b
--- /dev/null
+++ b/include/linux/phy_link_topology.h
@@ -0,0 +1,72 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * PHY device list allow maintaining a list of PHY devices that are
+ * part of a netdevice's link topology. PHYs can for example be chained,
+ * as is the case when using a PHY that exposes an SFP module, on which an
+ * SFP transceiver that embeds a PHY is connected.
+ *
+ * This list can then be used by userspace to leverage individual PHY
+ * capabilities.
+ */
+#ifndef __PHY_LINK_TOPOLOGY_H
+#define __PHY_LINK_TOPOLOGY_H
+
+#include <linux/ethtool.h>
+#include <linux/phy_link_topology_core.h>
+
+struct xarray;
+struct phy_device;
+struct net_device;
+struct sfp_bus;
+
+struct phy_device_node {
+ enum phy_upstream upstream_type;
+
+ union {
+ struct net_device *netdev;
+ struct phy_device *phydev;
+ } upstream;
+
+ struct sfp_bus *parent_sfp_bus;
+
+ struct phy_device *phy;
+};
+
+struct phy_link_topology {
+ struct xarray phys;
+ u32 next_phy_index;
+};
+
+static inline struct phy_device *
+phy_link_topo_get_phy(struct phy_link_topology *topo, u32 phyindex)
+{
+ struct phy_device_node *pdn = xa_load(&topo->phys, phyindex);
+
+ if (pdn)
+ return pdn->phy;
+
+ return NULL;
+}
+
+#if IS_ENABLED(CONFIG_PHYLIB)
+int phy_link_topo_add_phy(struct phy_link_topology *topo,
+ struct phy_device *phy,
+ enum phy_upstream upt, void *upstream);
+
+void phy_link_topo_del_phy(struct phy_link_topology *lt, struct phy_device *phy);
+
+#else
+static inline int phy_link_topo_add_phy(struct phy_link_topology *topo,
+ struct phy_device *phy,
+ enum phy_upstream upt, void *upstream)
+{
+ return 0;
+}
+
+static inline void phy_link_topo_del_phy(struct phy_link_topology *topo,
+ struct phy_device *phy)
+{
+}
+#endif
+
+#endif /* __PHY_LINK_TOPOLOGY_H */
diff --git a/include/linux/phy_link_topology_core.h b/include/linux/phy_link_topology_core.h
new file mode 100644
index 000000000000..b1265428979b
--- /dev/null
+++ b/include/linux/phy_link_topology_core.h
@@ -0,0 +1,25 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __PHY_LINK_TOPOLOGY_CORE_H
+#define __PHY_LINK_TOPOLOGY_CORE_H
+
+struct phy_link_topology;
+
+#if IS_ENABLED(CONFIG_PHYLIB)
+
+struct phy_link_topology *phy_link_topo_create(struct net_device *dev);
+void phy_link_topo_destroy(struct phy_link_topology *topo);
+
+#else
+
+static inline struct phy_link_topology *phy_link_topo_create(struct net_device *dev)
+{
+ return NULL;
+}
+
+static inline void phy_link_topo_destroy(struct phy_link_topology *topo)
+{
+}
+
+#endif
+
+#endif /* __PHY_LINK_TOPOLOGY_CORE_H */
diff --git a/include/uapi/linux/ethtool.h b/include/uapi/linux/ethtool.h
index 06ef6b78b7de..01ba529dbb6d 100644
--- a/include/uapi/linux/ethtool.h
+++ b/include/uapi/linux/ethtool.h
@@ -2220,4 +2220,20 @@ struct ethtool_link_settings {
* __u32 map_lp_advertising[link_mode_masks_nwords];
*/
};
+
+/**
+ * enum phy_upstream - Represents the upstream component a given PHY device
+ * is connected to, as in what is on the other end of the MII bus. Most PHYs
+ * will be attached to an Ethernet MAC controller, but in some cases, there's
+ * an intermediate PHY used as a media-converter, which will driver another
+ * MII interface as its output.
+ * @PHY_UPSTREAM_MAC: Upstream component is a MAC (a switch port,
+ * or ethernet controller)
+ * @PHY_UPSTREAM_PHY: Upstream component is a PHY (likely a media converter)
+ */
+enum phy_upstream {
+ PHY_UPSTREAM_MAC,
+ PHY_UPSTREAM_PHY,
+};
+
#endif /* _UAPI_LINUX_ETHTOOL_H */
diff --git a/net/core/dev.c b/net/core/dev.c
index cb2dab0feee0..0fed31da523a 100644
--- a/net/core/dev.c
+++ b/net/core/dev.c
@@ -153,6 +153,7 @@
#include <linux/prandom.h>
#include <linux/once_lite.h>
#include <net/netdev_rx_queue.h>
+#include <linux/phy_link_topology_core.h>
#include "dev.h"
#include "net-sysfs.h"
@@ -10875,6 +10876,12 @@ struct net_device *alloc_netdev_mqs(int sizeof_priv, const char *name,
#ifdef CONFIG_NET_SCHED
hash_init(dev->qdisc_hash);
#endif
+ dev->link_topo = phy_link_topo_create(dev);
+ if (IS_ERR(dev->link_topo)) {
+ dev->link_topo = NULL;
+ goto free_all;
+ }
+
dev->priv_flags = IFF_XMIT_DST_RELEASE | IFF_XMIT_DST_RELEASE_PERM;
setup(dev);
@@ -10963,6 +10970,8 @@ void free_netdev(struct net_device *dev)
free_percpu(dev->xdp_bulkq);
dev->xdp_bulkq = NULL;
+ phy_link_topo_destroy(dev->link_topo);
+
/* Compatibility with error handling in drivers */
if (dev->reg_state == NETREG_UNINITIALIZED) {
netdev_freemem(dev);
--
2.43.0
Pass the phy_device as a parameter to the sfp upstream .disconnect_phy
operation. This is preparatory work to help track phy devices across
a net_device's link.
Signed-off-by: Maxime Chevallier <[email protected]>
---
V6: Moved an incorrectly added hunk from the previous series to patch 0003
V5: No changes
V4: No changes
V3: No changes
drivers/net/phy/phylink.c | 3 ++-
drivers/net/phy/sfp-bus.c | 4 ++--
include/linux/sfp.h | 2 +-
3 files changed, 5 insertions(+), 4 deletions(-)
diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index ed0b4ccaa6a6..a816391add12 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -3385,7 +3385,8 @@ static int phylink_sfp_connect_phy(void *upstream, struct phy_device *phy)
return ret;
}
-static void phylink_sfp_disconnect_phy(void *upstream)
+static void phylink_sfp_disconnect_phy(void *upstream,
+ struct phy_device *phydev)
{
phylink_disconnect_phy(upstream);
}
diff --git a/drivers/net/phy/sfp-bus.c b/drivers/net/phy/sfp-bus.c
index db39dec7f247..e05013aeecc3 100644
--- a/drivers/net/phy/sfp-bus.c
+++ b/drivers/net/phy/sfp-bus.c
@@ -486,7 +486,7 @@ static void sfp_unregister_bus(struct sfp_bus *bus)
bus->socket_ops->stop(bus->sfp);
bus->socket_ops->detach(bus->sfp);
if (bus->phydev && ops && ops->disconnect_phy)
- ops->disconnect_phy(bus->upstream);
+ ops->disconnect_phy(bus->upstream, bus->phydev);
}
bus->registered = false;
}
@@ -742,7 +742,7 @@ void sfp_remove_phy(struct sfp_bus *bus)
const struct sfp_upstream_ops *ops = sfp_get_upstream_ops(bus);
if (ops && ops->disconnect_phy)
- ops->disconnect_phy(bus->upstream);
+ ops->disconnect_phy(bus->upstream, bus->phydev);
bus->phydev = NULL;
}
EXPORT_SYMBOL_GPL(sfp_remove_phy);
diff --git a/include/linux/sfp.h b/include/linux/sfp.h
index 9346cd44814d..0573e53b0c11 100644
--- a/include/linux/sfp.h
+++ b/include/linux/sfp.h
@@ -544,7 +544,7 @@ struct sfp_upstream_ops {
void (*link_down)(void *priv);
void (*link_up)(void *priv);
int (*connect_phy)(void *priv, struct phy_device *);
- void (*disconnect_phy)(void *priv);
+ void (*disconnect_phy)(void *priv, struct phy_device *);
};
#if IS_ENABLED(CONFIG_SFP)
--
2.43.0
The newly introduced phy_link_topology tracks all ethernet PHYs that are
attached to a netdevice. Document the base principle, internal and
external APIs. As the phy_link_topology is expected to be extended, this
documentation will hold any further improvements and additions made
relative to topology handling.
Signed-off-by: Maxime Chevallier <[email protected]>
---
V6: No changes
V5: Fixed a lot of typos
V4: No changes
V3: New patch
Documentation/networking/index.rst | 1 +
.../networking/phy-link-topology.rst | 121 ++++++++++++++++++
2 files changed, 122 insertions(+)
create mode 100644 Documentation/networking/phy-link-topology.rst
diff --git a/Documentation/networking/index.rst b/Documentation/networking/index.rst
index 69f3d6dcd9fd..a2c45a75a4a6 100644
--- a/Documentation/networking/index.rst
+++ b/Documentation/networking/index.rst
@@ -88,6 +88,7 @@ Contents:
operstates
packet_mmap
phonet
+ phy-link-topology
pktgen
plip
ppp_generic
diff --git a/Documentation/networking/phy-link-topology.rst b/Documentation/networking/phy-link-topology.rst
new file mode 100644
index 000000000000..1fd8e904ef4b
--- /dev/null
+++ b/Documentation/networking/phy-link-topology.rst
@@ -0,0 +1,121 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=================
+PHY link topology
+=================
+
+Overview
+========
+
+The PHY link topology representation in the networking stack aims at representing
+the hardware layout for any given Ethernet link.
+
+An Ethernet Interface from userspace's point of view is nothing but a
+:c:type:`struct net_device <net_device>`, which exposes configuration options
+through the legacy ioctls and the ethool netlink commands. The base assumption
+when designing these configuration channels were that the link looked
+something like this ::
+
+ +-----------------------+ +----------+ +--------------+
+ | Ethernet Controller / | | Ethernet | | Connector / |
+ | MAC | ------ | PHY | ---- | Port | ---... to LP
+ +-----------------------+ +----------+ +--------------+
+ struct net_device struct phy_device
+
+Commands that needs to configure the PHY will go through the net_device.phydev
+field to reach the PHY and perform the relevant configuration.
+
+This assumption falls apart in more complex topologies that can arise when,
+for example, using SFP transceivers (although that's not the only specific case).
+
+Here, we have 2 basic scenarios. Either the MAC is able to output a serialized
+interface, that can directly be fed to an SFP cage, such as SGMII, 1000BaseX,
+10GBaseR, etc.
+
+The link topology then looks like this (when an SFP module is inserted) ::
+
+ +-----+ SGMII +------------+
+ | MAC | ------- | SFP Module |
+ +-----+ +------------+
+
+Knowing that some modules embed a PHY, the actual link is more like ::
+
+ +-----+ SGMII +--------------+
+ | MAC | -------- | PHY (on SFP) |
+ +-----+ +--------------+
+
+In this case, the SFP PHY is handled by phylib, and registered by phylink through
+its SFP upstream ops.
+
+Now some Ethernet controllers aren't able to output a serialized interface, so
+we can't directly connect them to an SFP cage. However, some PHYs can be used
+as media-converters, to translate the non-serialized MAC MII interface to a
+serialized MII interface fed to the SFP ::
+
+ +-----+ RGMII +-----------------------+ SGMII +--------------+
+ | MAC | ------- | PHY (media converter) | ------- | PHY (on SFP) |
+ +-----+ +-----------------------+ +--------------+
+
+This is where the model of having a single net_device.phydev pointer shows its
+limitations, as we now have 2 PHYs on the link.
+
+The phy_link topology framework aims at providing a way to keep track of every
+PHY on the link, for use by both kernel drivers and subsystems, but also to
+report the topology to userspace, allowing to target individual PHYs in configuration
+commands.
+
+API
+===
+
+The :c:type:`struct phy_link_topology <phy_link_topology>` is a per-netdevice
+resource, that gets initialized at netdevice creation. Once it's initialized,
+it is then possible to register PHYs to the topology through :
+
+:c:func:`phy_link_topo_add_phy`
+
+Besides registering the PHY to the topology, this call will also assign a unique
+index to the PHY, which can then be reported to userspace to refer to this PHY
+(akin to the ifindex). This index is a u32, ranging from 1 to U32_MAX. The value
+0 is reserved to indicate the PHY doesn't belong to any topology yet.
+
+The PHY can then be removed from the topology through
+
+:c:func:`phy_link_topo_del_phy`
+
+These function are already hooked into the phylib subsystem, so all PHYs that
+are linked to a net_device through :c:func:`phy_attach_direct` will automatically
+join the netdev's topology.
+
+PHYs that are on a SFP module will also be automatically registered IF the SFP
+upstream is phylink (so, no media-converter).
+
+PHY drivers that can be used as SFP upstream need to call :c:func:`phy_sfp_attach_phy`
+and :c:func:`phy_sfp_detach_phy`, which can be used as a
+.attach_phy / .detach_phy implementation for the
+:c:type:`struct sfp_upstream_ops <sfp_upstream_ops>`.
+
+UAPI
+====
+
+There exist a set of netlink commands to query the link topology from userspace,
+see ``Documentation/networking/ethtool-netlink.rst``.
+
+The whole point of having a topology representation is to assign the phyindex
+field in :c:type:`struct phy_device <phy_device>`. This index is reported to
+userspace using the ``ETHTOOL_MSG_PHY_GET`` ethtnl command. Performing a DUMP operation
+will result in all PHYs from all net_device being listed. The DUMP command
+accepts either a ``ETHTOOL_A_HEADER_DEV_INDEX`` or ``ETHTOOL_A_HEADER_DEV_NAME``
+to be passed in the request to filter the DUMP to a single net_device.
+
+The retrieved index can then be passed as a request parameter using the
+``ETHTOOL_A_HEADER_PHY_INDEX`` field in the following ethnl commands :
+
+* ``ETHTOOL_MSG_STRSET_GET`` to get the stats string set from a given PHY
+* ``ETHTOOL_MSG_CABLE_TEST_ACT`` and ``ETHTOOL_MSG_CABLE_TEST_ACT``, to perform
+ cable testing on a given PHY on the link (most likely the outermost PHY)
+* ``ETHTOOL_MSG_PSE_SET`` and ``ETHTOOL_MSG_PSE_GET`` for PHY-controlled PoE and PSE settings
+* ``ETHTOOL_MSG_PLCA_GET_CFG``, ``ETHTOOL_MSG_PLCA_SET_CFG`` and ``ETHTOOL_MSG_PLCA_GET_STATUS``
+ to set the PLCA (Physical Layer Collision Avoidance) parameters
+
+Note that the PHY index can be passed to other requests, which will silently
+ignore it if present and irrelevant.
--
2.43.0
PSE and PD configuration is a PHY-specific command. Instead of targeting
the command towards dev->phydev, use the request to pick the targeted
PHY device.
Signed-off-by: Maxime Chevallier <[email protected]>
---
V6: Use dedicated policy
V5: Added-back an incorrectly removed check
V4: No changes
V3: No changes
V2: New patch
net/ethtool/pse-pd.c | 13 +++++--------
1 file changed, 5 insertions(+), 8 deletions(-)
diff --git a/net/ethtool/pse-pd.c b/net/ethtool/pse-pd.c
index cc478af77111..be50d79122c4 100644
--- a/net/ethtool/pse-pd.c
+++ b/net/ethtool/pse-pd.c
@@ -28,15 +28,13 @@ struct pse_reply_data {
/* PSE_GET */
const struct nla_policy ethnl_pse_get_policy[ETHTOOL_A_PSE_HEADER + 1] = {
- [ETHTOOL_A_PSE_HEADER] = NLA_POLICY_NESTED(ethnl_header_policy),
+ [ETHTOOL_A_PSE_HEADER] = NLA_POLICY_NESTED(ethnl_header_policy_phy),
};
-static int pse_get_pse_attributes(struct net_device *dev,
+static int pse_get_pse_attributes(struct phy_device *phydev,
struct netlink_ext_ack *extack,
struct pse_reply_data *data)
{
- struct phy_device *phydev = dev->phydev;
-
if (!phydev) {
NL_SET_ERR_MSG(extack, "No PHY is attached");
return -EOPNOTSUPP;
@@ -64,7 +62,7 @@ static int pse_prepare_data(const struct ethnl_req_info *req_base,
if (ret < 0)
return ret;
- ret = pse_get_pse_attributes(dev, info->extack, data);
+ ret = pse_get_pse_attributes(req_base->phydev, info->extack, data);
ethnl_ops_complete(dev);
@@ -109,7 +107,7 @@ static int pse_fill_reply(struct sk_buff *skb,
/* PSE_SET */
const struct nla_policy ethnl_pse_set_policy[ETHTOOL_A_PSE_MAX + 1] = {
- [ETHTOOL_A_PSE_HEADER] = NLA_POLICY_NESTED(ethnl_header_policy),
+ [ETHTOOL_A_PSE_HEADER] = NLA_POLICY_NESTED(ethnl_header_policy_phy),
[ETHTOOL_A_PODL_PSE_ADMIN_CONTROL] =
NLA_POLICY_RANGE(NLA_U32, ETHTOOL_PODL_PSE_ADMIN_STATE_DISABLED,
ETHTOOL_PODL_PSE_ADMIN_STATE_ENABLED),
@@ -124,7 +122,6 @@ ethnl_set_pse_validate(struct ethnl_req_info *req_info, struct genl_info *info)
static int
ethnl_set_pse(struct ethnl_req_info *req_info, struct genl_info *info)
{
- struct net_device *dev = req_info->dev;
struct pse_control_config config = {};
struct nlattr **tb = info->attrs;
struct phy_device *phydev;
@@ -132,7 +129,7 @@ ethnl_set_pse(struct ethnl_req_info *req_info, struct genl_info *info)
/* this values are already validated by the ethnl_pse_set_policy */
config.admin_cotrol = nla_get_u32(tb[ETHTOOL_A_PODL_PSE_ADMIN_CONTROL]);
- phydev = dev->phydev;
+ phydev = req_info->phydev;
if (!phydev) {
NL_SET_ERR_MSG(info->extack, "No PHY is attached");
return -EOPNOTSUPP;
--
2.43.0
PLCA is a PHY-specific command. Instead of targeting the command
towards dev->phydev, use the request to pick the targeted PHY.
Signed-off-by: Maxime Chevallier <[email protected]>
---
V6: Use dedicated policy
V5: Added Andrew's R-b
V4: No changes
V3: No changes
V2: New patch
net/ethtool/plca.c | 19 +++++++++----------
1 file changed, 9 insertions(+), 10 deletions(-)
diff --git a/net/ethtool/plca.c b/net/ethtool/plca.c
index b1e2e3b5027f..43b31a4a164e 100644
--- a/net/ethtool/plca.c
+++ b/net/ethtool/plca.c
@@ -25,7 +25,7 @@ struct plca_reply_data {
const struct nla_policy ethnl_plca_get_cfg_policy[] = {
[ETHTOOL_A_PLCA_HEADER] =
- NLA_POLICY_NESTED(ethnl_header_policy),
+ NLA_POLICY_NESTED(ethnl_header_policy_phy),
};
static void plca_update_sint(int *dst, struct nlattr **tb, u32 attrid,
@@ -61,7 +61,7 @@ static int plca_get_cfg_prepare_data(const struct ethnl_req_info *req_base,
int ret;
// check that the PHY device is available and connected
- if (!dev->phydev) {
+ if (!req_base->phydev) {
ret = -EOPNOTSUPP;
goto out;
}
@@ -80,7 +80,7 @@ static int plca_get_cfg_prepare_data(const struct ethnl_req_info *req_base,
memset(&data->plca_cfg, 0xff,
sizeof_field(struct plca_reply_data, plca_cfg));
- ret = ops->get_plca_cfg(dev->phydev, &data->plca_cfg);
+ ret = ops->get_plca_cfg(req_base->phydev, &data->plca_cfg);
ethnl_ops_complete(dev);
out:
@@ -129,7 +129,7 @@ static int plca_get_cfg_fill_reply(struct sk_buff *skb,
const struct nla_policy ethnl_plca_set_cfg_policy[] = {
[ETHTOOL_A_PLCA_HEADER] =
- NLA_POLICY_NESTED(ethnl_header_policy),
+ NLA_POLICY_NESTED(ethnl_header_policy_phy),
[ETHTOOL_A_PLCA_ENABLED] = NLA_POLICY_MAX(NLA_U8, 1),
[ETHTOOL_A_PLCA_NODE_ID] = NLA_POLICY_MAX(NLA_U32, 255),
[ETHTOOL_A_PLCA_NODE_CNT] = NLA_POLICY_RANGE(NLA_U32, 1, 255),
@@ -141,7 +141,6 @@ const struct nla_policy ethnl_plca_set_cfg_policy[] = {
static int
ethnl_set_plca(struct ethnl_req_info *req_info, struct genl_info *info)
{
- struct net_device *dev = req_info->dev;
const struct ethtool_phy_ops *ops;
struct nlattr **tb = info->attrs;
struct phy_plca_cfg plca_cfg;
@@ -149,7 +148,7 @@ ethnl_set_plca(struct ethnl_req_info *req_info, struct genl_info *info)
int ret;
// check that the PHY device is available and connected
- if (!dev->phydev)
+ if (!req_info->phydev)
return -EOPNOTSUPP;
ops = ethtool_phy_ops;
@@ -168,7 +167,7 @@ ethnl_set_plca(struct ethnl_req_info *req_info, struct genl_info *info)
if (!mod)
return 0;
- ret = ops->set_plca_cfg(dev->phydev, &plca_cfg, info->extack);
+ ret = ops->set_plca_cfg(req_info->phydev, &plca_cfg, info->extack);
return ret < 0 ? ret : 1;
}
@@ -191,7 +190,7 @@ const struct ethnl_request_ops ethnl_plca_cfg_request_ops = {
const struct nla_policy ethnl_plca_get_status_policy[] = {
[ETHTOOL_A_PLCA_HEADER] =
- NLA_POLICY_NESTED(ethnl_header_policy),
+ NLA_POLICY_NESTED(ethnl_header_policy_phy),
};
static int plca_get_status_prepare_data(const struct ethnl_req_info *req_base,
@@ -204,7 +203,7 @@ static int plca_get_status_prepare_data(const struct ethnl_req_info *req_base,
int ret;
// check that the PHY device is available and connected
- if (!dev->phydev) {
+ if (!req_base->phydev) {
ret = -EOPNOTSUPP;
goto out;
}
@@ -223,7 +222,7 @@ static int plca_get_status_prepare_data(const struct ethnl_req_info *req_base,
memset(&data->plca_st, 0xff,
sizeof_field(struct plca_reply_data, plca_st));
- ret = ops->get_plca_status(dev->phydev, &data->plca_st);
+ ret = ops->get_plca_status(req_base->phydev, &data->plca_st);
ethnl_ops_complete(dev);
out:
return ret;
--
2.43.0
On Fri, 26 Jan 2024 19:38:37 +0100 Maxime Chevallier wrote:
> Most of the changes were from Jakub's and Russell's reviews, the main
> point being a rework of the netlink API, removing uneeded nests and
> cleaning-up the dump code. Thanks's Jakub for all the tips, hopefulle
> the API is cleaner now.
Didn't get a chance to look today, sorry, but it appears to break
allmodconfig build:
ld: net/core/dev.o: in function `free_netdev':
dev.c:(.text+0x76e1): undefined reference to `phy_link_topo_destroy'
ld: net/core/dev.o: in function `alloc_netdev_mqs':
dev.c:(.text+0x79c2): undefined reference to `phy_link_topo_create'
so maybe fix up and post v7?
--
pw-bot: cr