Samsung Galaxy S5 has many variants. Currently, the only supported one
is klte. Samsung Galaxy S5 China (kltechn) is the China edition of
klte, and it can mostly work with the klte DTB, with only LEDs and WiFi
missing.
This patchset splits out the common part of klte DTS into klte-common
DTSI, and adds DTS for kltechn by fixing up the GPIO pins for the LEDs
and GPIO expander connected by the WiFi module. A "brcm,board-type"
property is added into the wifi@1 node of the common DTSI to allow all
klte* variants to load the same NVRAM file.
Signed-off-by: Rong Zhang <[email protected]>
---
Changes in v2:
- Split out the common part of klte DTS into klte-common DTSI.
- Fix dt-binding to make it consistent with kltechn compatible.
- Link to v1: https://lore.kernel.org/r/[email protected]/
---
Rong Zhang (4):
ARM: dts: qcom: msm8974: Split out common part of samsung-klte
ARM: dts: qcom: msm8974-klte-common: Pin WiFi board type
dt-bindings: arm: qcom: Add Samsung Galaxy S5 China (kltechn)
ARM: dts: qcom: msm8974: Add DTS for Samsung Galaxy S5 China (kltechn)
.../devicetree/bindings/arm/qcom.yaml | 7 +
arch/arm/boot/dts/qcom/Makefile | 1 +
.../qcom-msm8974pro-samsung-klte-common.dtsi | 818 ++++++++++++++++++
.../dts/qcom/qcom-msm8974pro-samsung-klte.dts | 813 +----------------
.../qcom/qcom-msm8974pro-samsung-kltechn.dts | 16 +
5 files changed, 848 insertions(+), 807 deletions(-)
create mode 100644 arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte-common.dtsi
create mode 100644 arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-kltechn.dts
base-commit: 3a5879d495b226d0404098e3564462d5f1daa33b
--
2.43.0
Samsung Galaxy S5 has many variants. Variants that support LTE use klte*
as their codename. Currently, the only supported one is the one without
any suffix, namely, klte. It is known that other klte* variants have
only minor differences compared to klte and can mostly work with the
klte DTB.
Split the common part into a common DTSI so that it can be imported in
the DTS of klte and other klte* variants.
Signed-off-by: Rong Zhang <[email protected]>
---
.../qcom-msm8974pro-samsung-klte-common.dtsi | 812 +++++++++++++++++
.../dts/qcom/qcom-msm8974pro-samsung-klte.dts | 813 +-----------------
2 files changed, 818 insertions(+), 807 deletions(-)
create mode 100644 arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte-common.dtsi
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte-common.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte-common.dtsi
new file mode 100644
index 000000000000..11e35b34ebd6
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte-common.dtsi
@@ -0,0 +1,812 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974pro.dtsi"
+#include "pma8084.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ chassis-type = "handset";
+
+ aliases {
+ serial0 = &blsp1_uart1;
+ mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+ mmc1 = &sdhc_3; /* SDC2 SD card slot */
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys_pin_a>;
+
+ key-volume-down {
+ label = "volume_down";
+ gpios = <&pma8084_gpios 2 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ debounce-interval = <15>;
+ };
+
+ key-home {
+ label = "home_key";
+ gpios = <&pma8084_gpios 3 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_HOMEPAGE>;
+ wakeup-source;
+ debounce-interval = <15>;
+ };
+
+ key-volume-up {
+ label = "volume_up";
+ gpios = <&pma8084_gpios 5 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_VOLUMEUP>;
+ debounce-interval = <15>;
+ };
+ };
+
+ i2c-gpio-touchkey {
+ compatible = "i2c-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ sda-gpios = <&tlmm 95 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&tlmm 96 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_touchkey_pins>;
+
+ touchkey@20 {
+ compatible = "cypress,tm2-touchkey";
+ reg = <0x20>;
+
+ interrupt-parent = <&pma8084_gpios>;
+ interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&touchkey_pin>;
+
+ vcc-supply = <&max77826_ldo15>;
+ vdd-supply = <&pma8084_l19>;
+
+ linux,keycodes = <KEY_APPSELECT KEY_BACK>;
+ };
+ };
+
+ i2c_led_gpio: i2c-gpio-led {
+ compatible = "i2c-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_led_gpioex_pins>;
+
+ i2c-gpio,delay-us = <2>;
+
+ gpio_expander: gpio@20 {
+ compatible = "nxp,pcal6416";
+ reg = <0x20>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ vcc-supply = <&pma8084_s4>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpioex_pin>;
+
+ reset-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
+ };
+
+ led-controller@30 {
+ compatible = "panasonic,an30259a";
+ reg = <0x30>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@1 {
+ reg = <1>;
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ led@2 {
+ reg = <2>;
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ };
+
+ led@3 {
+ reg = <3>;
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+ };
+ };
+
+ vreg_wlan: wlan-regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "wl-reg";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio_expander 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vreg_panel: panel-regulator {
+ compatible = "regulator-fixed";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&panel_en_pin>;
+
+ regulator-name = "panel-vddr-reg";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+
+ gpio = <&pma8084_gpios 14 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vreg_vph_pwr: vreg-vph-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "vph-pwr";
+
+ regulator-min-microvolt = <3600000>;
+ regulator-max-microvolt = <3600000>;
+
+ regulator-always-on;
+ };
+};
+
+&blsp1_i2c2 {
+ status = "okay";
+
+ touchscreen@20 {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x20>;
+
+ interrupt-parent = <&pma8084_gpios>;
+ interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
+
+ vdd-supply = <&max77826_ldo13>;
+ vio-supply = <&pma8084_lvs2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&touch_pin>;
+
+ syna,startup-delay-ms = <100>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rmi4-f01@1 {
+ reg = <0x1>;
+ syna,nosleep-mode = <1>;
+ };
+
+ rmi4-f12@12 {
+ reg = <0x12>;
+ syna,sensor-type = <1>;
+ };
+ };
+};
+
+&blsp1_i2c6 {
+ status = "okay";
+
+ pmic@60 {
+ reg = <0x60>;
+ compatible = "maxim,max77826";
+
+ regulators {
+ max77826_ldo1: LDO1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ max77826_ldo2: LDO2 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ max77826_ldo3: LDO3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ max77826_ldo4: LDO4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ max77826_ldo5: LDO5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ max77826_ldo6: LDO6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ max77826_ldo7: LDO7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ max77826_ldo8: LDO8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ max77826_ldo9: LDO9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ max77826_ldo10: LDO10 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ max77826_ldo11: LDO11 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ max77826_ldo12: LDO12 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ max77826_ldo13: LDO13 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ max77826_ldo14: LDO14 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ max77826_ldo15: LDO15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ max77826_buck: BUCK {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ max77826_buckboost: BUCKBOOST {
+ regulator-min-microvolt = <3400000>;
+ regulator-max-microvolt = <3400000>;
+ };
+ };
+ };
+};
+
+&blsp1_uart2 {
+ status = "okay";
+};
+
+&blsp2_i2c6 {
+ status = "okay";
+
+ fuelgauge@36 {
+ compatible = "maxim,max17048";
+ reg = <0x36>;
+
+ maxim,double-soc;
+ maxim,rcomp = /bits/ 8 <0x56>;
+
+ interrupt-parent = <&pma8084_gpios>;
+ interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&fuelgauge_pin>;
+ };
+};
+
+&blsp2_uart2 {
+ status = "okay";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp2_uart2_pins_active>;
+ pinctrl-1 = <&blsp2_uart2_pins_sleep>;
+
+ bluetooth {
+ compatible = "brcm,bcm43540-bt";
+ max-speed = <3000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_pins>;
+ device-wakeup-gpios = <&tlmm 91 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&gpio_expander 9 GPIO_ACTIVE_HIGH>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <75 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host-wakeup";
+ };
+};
+
+&gpu {
+ status = "okay";
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dsi0 {
+ status = "okay";
+
+ vdda-supply = <&pma8084_l2>;
+ vdd-supply = <&pma8084_l22>;
+ vddio-supply = <&pma8084_l12>;
+
+ panel: panel@0 {
+ reg = <0>;
+ compatible = "samsung,s6e3fa2";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&panel_te_pin &panel_rst_pin>;
+
+ iovdd-supply = <&pma8084_lvs4>;
+ vddr-supply = <&vreg_panel>;
+
+ reset-gpios = <&pma8084_gpios 17 GPIO_ACTIVE_LOW>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+ };
+};
+
+&mdss_dsi0_out {
+ remote-endpoint = <&panel_in>;
+ data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+ status = "okay";
+
+ vddio-supply = <&pma8084_l12>;
+};
+
+&pma8084_gpios {
+ gpio_keys_pin_a: gpio-keys-active-state {
+ pins = "gpio2", "gpio3", "gpio5";
+ function = "normal";
+
+ bias-pull-up;
+ power-source = <PMA8084_GPIO_S4>;
+ };
+
+ touchkey_pin: touchkey-int-state {
+ pins = "gpio6";
+ function = "normal";
+ bias-disable;
+ input-enable;
+ power-source = <PMA8084_GPIO_S4>;
+ };
+
+ touch_pin: touchscreen-int-state {
+ pins = "gpio8";
+ function = "normal";
+ bias-disable;
+ input-enable;
+ power-source = <PMA8084_GPIO_S4>;
+ };
+
+ panel_en_pin: panel-en-state {
+ pins = "gpio14";
+ function = "normal";
+ bias-pull-up;
+ power-source = <PMA8084_GPIO_S4>;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ };
+
+ wlan_sleep_clk_pin: wlan-sleep-clk-state {
+ pins = "gpio16";
+ function = "func2";
+
+ output-high;
+ power-source = <PMA8084_GPIO_S4>;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
+ };
+
+ panel_rst_pin: panel-rst-state {
+ pins = "gpio17";
+ function = "normal";
+ bias-disable;
+ power-source = <PMA8084_GPIO_S4>;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ };
+
+ fuelgauge_pin: fuelgauge-int-state {
+ pins = "gpio21";
+ function = "normal";
+ bias-disable;
+ input-enable;
+ power-source = <PMA8084_GPIO_S4>;
+ };
+};
+
+&remoteproc_adsp {
+ status = "okay";
+ cx-supply = <&pma8084_s2>;
+};
+
+&remoteproc_mss {
+ status = "okay";
+ cx-supply = <&pma8084_s2>;
+ mss-supply = <&pma8084_s6>;
+ mx-supply = <&pma8084_s1>;
+ pll-supply = <&pma8084_l12>;
+};
+
+&rpm_requests {
+ regulators-0 {
+ compatible = "qcom,rpm-pma8084-regulators";
+
+ pma8084_s1: s1 {
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-always-on;
+ };
+
+ pma8084_s2: s2 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ pma8084_s3: s3 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ pma8084_s4: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pma8084_s5: s5 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ };
+
+ pma8084_s6: s6 {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ pma8084_l1: l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ pma8084_l2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pma8084_l3: l3 {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pma8084_l4: l4 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ pma8084_l5: l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pma8084_l6: l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pma8084_l7: l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pma8084_l8: l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pma8084_l9: l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pma8084_l10: l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pma8084_l11: l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ pma8084_l12: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ pma8084_l13: l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pma8084_l14: l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pma8084_l15: l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ pma8084_l16: l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ pma8084_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ pma8084_l18: l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ pma8084_l19: l19 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pma8084_l20: l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-system-load = <200000>;
+ regulator-allow-set-load;
+ };
+
+ pma8084_l21: l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-system-load = <200000>;
+ regulator-allow-set-load;
+ };
+
+ pma8084_l22: l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pma8084_l23: l23 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ pma8084_l24: l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };
+
+ pma8084_l25: l25 {
+ regulator-min-microvolt = <2100000>;
+ regulator-max-microvolt = <2100000>;
+ };
+
+ pma8084_l26: l26 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ pma8084_l27: l27 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ pma8084_lvs1: lvs1 {};
+ pma8084_lvs2: lvs2 {};
+ pma8084_lvs3: lvs3 {};
+ pma8084_lvs4: lvs4 {};
+
+ pma8084_5vs1: 5vs1 {};
+ };
+};
+
+&sdhc_1 {
+ status = "okay";
+
+ vmmc-supply = <&pma8084_l20>;
+ vqmmc-supply = <&pma8084_s4>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc1_on>;
+ pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+ status = "okay";
+ max-frequency = <100000000>;
+ vmmc-supply = <&vreg_wlan>;
+ vqmmc-supply = <&pma8084_s4>;
+ non-removable;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_on>;
+ pinctrl-1 = <&sdc2_off>;
+
+ wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host-wake";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_sleep_clk_pin &wifi_pin>;
+ };
+};
+
+&sdhc_3 {
+ status = "okay";
+ max-frequency = <100000000>;
+ vmmc-supply = <&pma8084_l21>;
+ vqmmc-supply = <&pma8084_l13>;
+
+ /*
+ * cd-gpio is intentionally disabled. If enabled, an SD card
+ * present during boot is not initialized correctly. Without
+ * cd-gpios the driver resorts to polling, so hotplug works.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdc3_on /* &sdhc3_cd_pin */>;
+ /* cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>; */
+};
+
+&tlmm {
+ /* This seems suspicious, but somebody with this device should look into it. */
+ blsp2_uart2_pins_active: blsp2-uart2-pins-active-state {
+ pins = "gpio45", "gpio46", "gpio47", "gpio48";
+ function = "blsp_uart8";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ blsp2_uart2_pins_sleep: blsp2-uart2-pins-sleep-state {
+ pins = "gpio45", "gpio46", "gpio47", "gpio48";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ bt_pins: bt-pins-state {
+ hostwake-pins {
+ pins = "gpio75";
+ function = "gpio";
+ drive-strength = <16>;
+ };
+
+ devwake-pins {
+ pins = "gpio91";
+ function = "gpio";
+ drive-strength = <2>;
+ };
+ };
+
+ sdc1_on: sdhc1-on-state {
+ clk-pins {
+ pins = "sdc1_clk";
+ drive-strength = <4>;
+ bias-disable;
+ };
+
+ cmd-data-pins {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <4>;
+ bias-pull-up;
+ };
+ };
+
+ sdc3_on: sdc3-on-state {
+ pins = "gpio35", "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
+ function = "sdc3";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ sdhc3_cd_pin: sdc3-cd-on-state {
+ pins = "gpio62";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ sdc2_on: sdhc2-on-state {
+ clk-pins {
+ pins = "sdc2_clk";
+ drive-strength = <6>;
+ bias-disable;
+ };
+
+ cmd-data-pins {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
+
+ i2c_touchkey_pins: i2c-touchkey-state {
+ pins = "gpio95", "gpio96";
+ function = "gpio";
+ bias-pull-up;
+ };
+
+ i2c_led_gpioex_pins: i2c-led-gpioex-state {
+ function = "gpio";
+ bias-pull-down;
+ };
+
+ gpioex_pin: gpioex-state {
+ pins = "gpio145";
+ function = "gpio";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ wifi_pin: wifi-state {
+ pins = "gpio92";
+ function = "gpio";
+ bias-pull-down;
+ };
+
+ panel_te_pin: panel-state {
+ pins = "gpio12";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&usb {
+ status = "okay";
+
+ phys = <&usb_hs1_phy>;
+ phy-select = <&tcsr 0xb000 0>;
+
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+};
+
+&usb_hs1_phy {
+ status = "okay";
+
+ v1p8-supply = <&pma8084_l6>;
+ v3p3-supply = <&pma8084_l24>;
+
+ qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
index b93539e2b87e..954665f3a9dd 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
@@ -1,817 +1,16 @@
// SPDX-License-Identifier: GPL-2.0
-#include "qcom-msm8974pro.dtsi"
-#include "pma8084.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-#include <dt-bindings/leds/common.h>
+#include "qcom-msm8974pro-samsung-klte-common.dtsi"
/ {
model = "Samsung Galaxy S5";
compatible = "samsung,klte", "qcom,msm8974pro", "qcom,msm8974";
- chassis-type = "handset";
-
- aliases {
- serial0 = &blsp1_uart1;
- mmc0 = &sdhc_1; /* SDC1 eMMC slot */
- mmc1 = &sdhc_3; /* SDC2 SD card slot */
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- gpio-keys {
- compatible = "gpio-keys";
-
- pinctrl-names = "default";
- pinctrl-0 = <&gpio_keys_pin_a>;
-
- key-volume-down {
- label = "volume_down";
- gpios = <&pma8084_gpios 2 GPIO_ACTIVE_LOW>;
- linux,input-type = <1>;
- linux,code = <KEY_VOLUMEDOWN>;
- debounce-interval = <15>;
- };
-
- key-home {
- label = "home_key";
- gpios = <&pma8084_gpios 3 GPIO_ACTIVE_LOW>;
- linux,input-type = <1>;
- linux,code = <KEY_HOMEPAGE>;
- wakeup-source;
- debounce-interval = <15>;
- };
-
- key-volume-up {
- label = "volume_up";
- gpios = <&pma8084_gpios 5 GPIO_ACTIVE_LOW>;
- linux,input-type = <1>;
- linux,code = <KEY_VOLUMEUP>;
- debounce-interval = <15>;
- };
- };
-
- i2c-gpio-touchkey {
- compatible = "i2c-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
- sda-gpios = <&tlmm 95 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- scl-gpios = <&tlmm 96 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c_touchkey_pins>;
-
- touchkey@20 {
- compatible = "cypress,tm2-touchkey";
- reg = <0x20>;
-
- interrupt-parent = <&pma8084_gpios>;
- interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
- pinctrl-names = "default";
- pinctrl-0 = <&touchkey_pin>;
-
- vcc-supply = <&max77826_ldo15>;
- vdd-supply = <&pma8084_l19>;
-
- linux,keycodes = <KEY_APPSELECT KEY_BACK>;
- };
- };
-
- i2c-gpio-led {
- compatible = "i2c-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
- scl-gpios = <&tlmm 121 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- sda-gpios = <&tlmm 120 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c_led_gpioex_pins>;
-
- i2c-gpio,delay-us = <2>;
-
- gpio_expander: gpio@20 {
- compatible = "nxp,pcal6416";
- reg = <0x20>;
-
- gpio-controller;
- #gpio-cells = <2>;
-
- vcc-supply = <&pma8084_s4>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&gpioex_pin>;
-
- reset-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
- };
-
- led-controller@30 {
- compatible = "panasonic,an30259a";
- reg = <0x30>;
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- led@1 {
- reg = <1>;
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_RED>;
- };
-
- led@2 {
- reg = <2>;
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_GREEN>;
- };
-
- led@3 {
- reg = <3>;
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_BLUE>;
- };
- };
- };
-
- vreg_wlan: wlan-regulator {
- compatible = "regulator-fixed";
-
- regulator-name = "wl-reg";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- gpio = <&gpio_expander 8 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vreg_panel: panel-regulator {
- compatible = "regulator-fixed";
-
- pinctrl-names = "default";
- pinctrl-0 = <&panel_en_pin>;
-
- regulator-name = "panel-vddr-reg";
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1500000>;
-
- gpio = <&pma8084_gpios 14 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vreg_vph_pwr: vreg-vph-pwr {
- compatible = "regulator-fixed";
- regulator-name = "vph-pwr";
-
- regulator-min-microvolt = <3600000>;
- regulator-max-microvolt = <3600000>;
-
- regulator-always-on;
- };
-};
-
-&blsp1_i2c2 {
- status = "okay";
-
- touchscreen@20 {
- compatible = "syna,rmi4-i2c";
- reg = <0x20>;
-
- interrupt-parent = <&pma8084_gpios>;
- interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
-
- vdd-supply = <&max77826_ldo13>;
- vio-supply = <&pma8084_lvs2>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&touch_pin>;
-
- syna,startup-delay-ms = <100>;
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- rmi4-f01@1 {
- reg = <0x1>;
- syna,nosleep-mode = <1>;
- };
-
- rmi4-f12@12 {
- reg = <0x12>;
- syna,sensor-type = <1>;
- };
- };
-};
-
-&blsp1_i2c6 {
- status = "okay";
-
- pmic@60 {
- reg = <0x60>;
- compatible = "maxim,max77826";
-
- regulators {
- max77826_ldo1: LDO1 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- max77826_ldo2: LDO2 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- };
-
- max77826_ldo3: LDO3 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- max77826_ldo4: LDO4 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- max77826_ldo5: LDO5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- max77826_ldo6: LDO6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- max77826_ldo7: LDO7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- max77826_ldo8: LDO8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- max77826_ldo9: LDO9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- max77826_ldo10: LDO10 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- max77826_ldo11: LDO11 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2950000>;
- };
-
- max77826_ldo12: LDO12 {
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <3300000>;
- };
-
- max77826_ldo13: LDO13 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- max77826_ldo14: LDO14 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- max77826_ldo15: LDO15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- max77826_buck: BUCK {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- max77826_buckboost: BUCKBOOST {
- regulator-min-microvolt = <3400000>;
- regulator-max-microvolt = <3400000>;
- };
- };
- };
-};
-
-&blsp1_uart2 {
- status = "okay";
-};
-
-&blsp2_i2c6 {
- status = "okay";
-
- fuelgauge@36 {
- compatible = "maxim,max17048";
- reg = <0x36>;
-
- maxim,double-soc;
- maxim,rcomp = /bits/ 8 <0x56>;
-
- interrupt-parent = <&pma8084_gpios>;
- interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&fuelgauge_pin>;
- };
-};
-
-&blsp2_uart2 {
- status = "okay";
-
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&blsp2_uart2_pins_active>;
- pinctrl-1 = <&blsp2_uart2_pins_sleep>;
-
- bluetooth {
- compatible = "brcm,bcm43540-bt";
- max-speed = <3000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&bt_pins>;
- device-wakeup-gpios = <&tlmm 91 GPIO_ACTIVE_HIGH>;
- shutdown-gpios = <&gpio_expander 9 GPIO_ACTIVE_HIGH>;
- interrupt-parent = <&tlmm>;
- interrupts = <75 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "host-wakeup";
- };
-};
-
-&gpu {
- status = "okay";
-};
-
-&mdss {
- status = "okay";
-};
-
-&mdss_dsi0 {
- status = "okay";
-
- vdda-supply = <&pma8084_l2>;
- vdd-supply = <&pma8084_l22>;
- vddio-supply = <&pma8084_l12>;
-
- panel: panel@0 {
- reg = <0>;
- compatible = "samsung,s6e3fa2";
-
- pinctrl-names = "default";
- pinctrl-0 = <&panel_te_pin &panel_rst_pin>;
-
- iovdd-supply = <&pma8084_lvs4>;
- vddr-supply = <&vreg_panel>;
-
- reset-gpios = <&pma8084_gpios 17 GPIO_ACTIVE_LOW>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&mdss_dsi0_out>;
- };
- };
- };
-};
-
-&mdss_dsi0_out {
- remote-endpoint = <&panel_in>;
- data-lanes = <0 1 2 3>;
-};
-
-&mdss_dsi0_phy {
- status = "okay";
-
- vddio-supply = <&pma8084_l12>;
};
-&pma8084_gpios {
- gpio_keys_pin_a: gpio-keys-active-state {
- pins = "gpio2", "gpio3", "gpio5";
- function = "normal";
-
- bias-pull-up;
- power-source = <PMA8084_GPIO_S4>;
- };
-
- touchkey_pin: touchkey-int-state {
- pins = "gpio6";
- function = "normal";
- bias-disable;
- input-enable;
- power-source = <PMA8084_GPIO_S4>;
- };
-
- touch_pin: touchscreen-int-state {
- pins = "gpio8";
- function = "normal";
- bias-disable;
- input-enable;
- power-source = <PMA8084_GPIO_S4>;
- };
-
- panel_en_pin: panel-en-state {
- pins = "gpio14";
- function = "normal";
- bias-pull-up;
- power-source = <PMA8084_GPIO_S4>;
- qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
- };
-
- wlan_sleep_clk_pin: wlan-sleep-clk-state {
- pins = "gpio16";
- function = "func2";
-
- output-high;
- power-source = <PMA8084_GPIO_S4>;
- qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
- };
-
- panel_rst_pin: panel-rst-state {
- pins = "gpio17";
- function = "normal";
- bias-disable;
- power-source = <PMA8084_GPIO_S4>;
- qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
- };
-
- fuelgauge_pin: fuelgauge-int-state {
- pins = "gpio21";
- function = "normal";
- bias-disable;
- input-enable;
- power-source = <PMA8084_GPIO_S4>;
- };
+&i2c_led_gpio {
+ scl-gpios = <&tlmm 121 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&tlmm 120 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
};
-&remoteproc_adsp {
- status = "okay";
- cx-supply = <&pma8084_s2>;
-};
-
-&remoteproc_mss {
- status = "okay";
- cx-supply = <&pma8084_s2>;
- mss-supply = <&pma8084_s6>;
- mx-supply = <&pma8084_s1>;
- pll-supply = <&pma8084_l12>;
-};
-
-&rpm_requests {
- regulators-0 {
- compatible = "qcom,rpm-pma8084-regulators";
-
- pma8084_s1: s1 {
- regulator-min-microvolt = <675000>;
- regulator-max-microvolt = <1050000>;
- regulator-always-on;
- };
-
- pma8084_s2: s2 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- pma8084_s3: s3 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- };
-
- pma8084_s4: s4 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_s5: s5 {
- regulator-min-microvolt = <2150000>;
- regulator-max-microvolt = <2150000>;
- };
-
- pma8084_s6: s6 {
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1050000>;
- };
-
- pma8084_l1: l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- pma8084_l2: l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- pma8084_l3: l3 {
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1200000>;
- };
-
- pma8084_l4: l4 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1225000>;
- };
-
- pma8084_l5: l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_l6: l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_l7: l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_l8: l8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_l9: l9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- pma8084_l10: l10 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- pma8084_l11: l11 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- };
-
- pma8084_l12: l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- pma8084_l13: l13 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- pma8084_l14: l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_l15: l15 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- pma8084_l16: l16 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- pma8084_l17: l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- pma8084_l18: l18 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- pma8084_l19: l19 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- pma8084_l20: l20 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-system-load = <200000>;
- regulator-allow-set-load;
- };
-
- pma8084_l21: l21 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-system-load = <200000>;
- regulator-allow-set-load;
- };
-
- pma8084_l22: l22 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3300000>;
- };
-
- pma8084_l23: l23 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- pma8084_l24: l24 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
-
- pma8084_l25: l25 {
- regulator-min-microvolt = <2100000>;
- regulator-max-microvolt = <2100000>;
- };
-
- pma8084_l26: l26 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2050000>;
- };
-
- pma8084_l27: l27 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1225000>;
- };
-
- pma8084_lvs1: lvs1 {};
- pma8084_lvs2: lvs2 {};
- pma8084_lvs3: lvs3 {};
- pma8084_lvs4: lvs4 {};
-
- pma8084_5vs1: 5vs1 {};
- };
-};
-
-&sdhc_1 {
- status = "okay";
-
- vmmc-supply = <&pma8084_l20>;
- vqmmc-supply = <&pma8084_s4>;
-
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sdc1_on>;
- pinctrl-1 = <&sdc1_off>;
-};
-
-&sdhc_2 {
- status = "okay";
- max-frequency = <100000000>;
- vmmc-supply = <&vreg_wlan>;
- vqmmc-supply = <&pma8084_s4>;
- non-removable;
-
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sdc2_on>;
- pinctrl-1 = <&sdc2_off>;
-
- wifi@1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
-
- interrupt-parent = <&tlmm>;
- interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "host-wake";
-
- pinctrl-names = "default";
- pinctrl-0 = <&wlan_sleep_clk_pin &wifi_pin>;
- };
-};
-
-&sdhc_3 {
- status = "okay";
- max-frequency = <100000000>;
- vmmc-supply = <&pma8084_l21>;
- vqmmc-supply = <&pma8084_l13>;
-
- /*
- * cd-gpio is intentionally disabled. If enabled, an SD card
- * present during boot is not initialized correctly. Without
- * cd-gpios the driver resorts to polling, so hotplug works.
- */
- pinctrl-names = "default";
- pinctrl-0 = <&sdc3_on /* &sdhc3_cd_pin */>;
- /* cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>; */
-};
-
-&tlmm {
- /* This seems suspicious, but somebody with this device should look into it. */
- blsp2_uart2_pins_active: blsp2-uart2-pins-active-state {
- pins = "gpio45", "gpio46", "gpio47", "gpio48";
- function = "blsp_uart8";
- drive-strength = <8>;
- bias-disable;
- };
-
- blsp2_uart2_pins_sleep: blsp2-uart2-pins-sleep-state {
- pins = "gpio45", "gpio46", "gpio47", "gpio48";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- };
-
- bt_pins: bt-pins-state {
- hostwake-pins {
- pins = "gpio75";
- function = "gpio";
- drive-strength = <16>;
- };
-
- devwake-pins {
- pins = "gpio91";
- function = "gpio";
- drive-strength = <2>;
- };
- };
-
- sdc1_on: sdhc1-on-state {
- clk-pins {
- pins = "sdc1_clk";
- drive-strength = <4>;
- bias-disable;
- };
-
- cmd-data-pins {
- pins = "sdc1_cmd", "sdc1_data";
- drive-strength = <4>;
- bias-pull-up;
- };
- };
-
- sdc3_on: sdc3-on-state {
- pins = "gpio35", "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
- function = "sdc3";
- drive-strength = <8>;
- bias-disable;
- };
-
- sdhc3_cd_pin: sdc3-cd-on-state {
- pins = "gpio62";
- function = "gpio";
-
- drive-strength = <2>;
- bias-disable;
- };
-
- sdc2_on: sdhc2-on-state {
- clk-pins {
- pins = "sdc2_clk";
- drive-strength = <6>;
- bias-disable;
- };
-
- cmd-data-pins {
- pins = "sdc2_cmd", "sdc2_data";
- drive-strength = <6>;
- bias-pull-up;
- };
- };
-
- i2c_touchkey_pins: i2c-touchkey-state {
- pins = "gpio95", "gpio96";
- function = "gpio";
- bias-pull-up;
- };
-
- i2c_led_gpioex_pins: i2c-led-gpioex-state {
- pins = "gpio120", "gpio121";
- function = "gpio";
- bias-pull-down;
- };
-
- gpioex_pin: gpioex-state {
- pins = "gpio145";
- function = "gpio";
- bias-pull-up;
- drive-strength = <2>;
- };
-
- wifi_pin: wifi-state {
- pins = "gpio92";
- function = "gpio";
- bias-pull-down;
- };
-
- panel_te_pin: panel-state {
- pins = "gpio12";
- function = "mdp_vsync";
- drive-strength = <2>;
- bias-disable;
- };
-};
-
-&usb {
- status = "okay";
-
- phys = <&usb_hs1_phy>;
- phy-select = <&tcsr 0xb000 0>;
-
- hnp-disable;
- srp-disable;
- adp-disable;
-};
-
-&usb_hs1_phy {
- status = "okay";
-
- v1p8-supply = <&pma8084_l6>;
- v3p3-supply = <&pma8084_l24>;
-
- qcom,init-seq = /bits/ 8 <0x1 0x64>;
+&i2c_led_gpioex_pins {
+ pins = "gpio120", "gpio121";
};
--
2.43.0
klte* variants have little difference in the WiFi part. Without
"brcm,board-type", variant-specific NVRAM file will be probed (e.g.,
klte probes samsung,klte). Pin it to "samsung,klte" to allow klte* to
load the same NVRAM file as klte.
Signed-off-by: Rong Zhang <[email protected]>
---
.../boot/dts/qcom/qcom-msm8974pro-samsung-klte-common.dtsi | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte-common.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte-common.dtsi
index 11e35b34ebd6..b5443fd5b425 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte-common.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte-common.dtsi
@@ -661,6 +661,12 @@ wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
+ /*
+ * Allow all klte* variants to load the same NVRAM file,
+ * as they have little difference in the WiFi part.
+ */
+ brcm,board-type = "samsung,klte";
+
interrupt-parent = <&tlmm>;
interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "host-wake";
--
2.43.0
Document Samsung Galaxy S5 China (kltechn) as a klte variant based on
msm8974pro. Also including "samsung,klte" in the compatible chain as
kltechn works fine with the klte DTB except for LEDs and WiFi missing.
Signed-off-by: Rong Zhang <[email protected]>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 1a5fb889a444..4979ccae2b64 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -227,6 +227,13 @@ properties:
- const: qcom,msm8974pro
- const: qcom,msm8974
+ - items:
+ - enum:
+ - samsung,kltechn
+ - const: samsung,klte
+ - const: qcom,msm8974pro
+ - const: qcom,msm8974
+
- items:
- const: qcom,msm8916-mtp
- const: qcom,msm8916-mtp/1
--
2.43.0
The only difference between Samsung Galaxy S5 China (kltechn) and klte
is the gpio pins of i2c_led_gpio. With pins corrected, the LEDs and WiFi
are able to work properly.
Signed-off-by: Rong Zhang <[email protected]>
---
arch/arm/boot/dts/qcom/Makefile | 1 +
.../dts/qcom/qcom-msm8974pro-samsung-kltechn.dts | 16 ++++++++++++++++
2 files changed, 17 insertions(+)
create mode 100644 arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-kltechn.dts
diff --git a/arch/arm/boot/dts/qcom/Makefile b/arch/arm/boot/dts/qcom/Makefile
index 9cc1e14e6cd0..5d7a34adf826 100644
--- a/arch/arm/boot/dts/qcom/Makefile
+++ b/arch/arm/boot/dts/qcom/Makefile
@@ -44,6 +44,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-msm8974pro-fairphone-fp2.dtb \
qcom-msm8974pro-oneplus-bacon.dtb \
qcom-msm8974pro-samsung-klte.dtb \
+ qcom-msm8974pro-samsung-kltechn.dtb \
qcom-msm8974pro-sony-xperia-shinano-castor.dtb \
qcom-mdm9615-wp8548-mangoh-green.dtb \
qcom-sdx55-mtp.dtb \
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-kltechn.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-kltechn.dts
new file mode 100644
index 000000000000..b902e31b16c2
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-kltechn.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974pro-samsung-klte-common.dtsi"
+
+/ {
+ model = "Samsung Galaxy S5 China";
+ compatible = "samsung,kltechn", "samsung,klte", "qcom,msm8974pro", "qcom,msm8974";
+};
+
+&i2c_led_gpio {
+ scl-gpios = <&tlmm 61 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&tlmm 60 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+};
+
+&i2c_led_gpioex_pins {
+ pins = "gpio60", "gpio61";
+};
--
2.43.0
On 27/01/2024 18:21, Rong Zhang wrote:
> Document Samsung Galaxy S5 China (kltechn) as a klte variant based on
> msm8974pro. Also including "samsung,klte" in the compatible chain as
> kltechn works fine with the klte DTB except for LEDs and WiFi missing.
>
> Signed-off-by: Rong Zhang <[email protected]>
> ---
This is a friendly reminder during the review process.
It looks like you received a tag and forgot to add it.
If you do not know the process, here is a short explanation:
Please add Acked-by/Reviewed-by/Tested-by tags when posting new
versions, under or above your Signed-off-by tag. Tag is "received", when
provided in a message replied to you on the mailing list. Tools like b4
can help here. However, there's no need to repost patches *only* to add
the tags. The upstream maintainer will do that for tags received on the
version they apply.
https://elixir.bootlin.com/linux/v6.5-rc3/source/Documentation/process/submitting-patches.rst#L577
If a tag was not added on purpose, please state why and what changed.
Best regards,
Krzysztof
On 27/01/2024 18:21, Rong Zhang wrote:
> Samsung Galaxy S5 has many variants. Variants that support LTE use klte*
> as their codename. Currently, the only supported one is the one without
> any suffix, namely, klte. It is known that other klte* variants have
> only minor differences compared to klte and can mostly work with the
> klte DTB.
>
> Split the common part into a common DTSI so that it can be imported in
> the DTS of klte and other klte* variants.
>
> Signed-off-by: Rong Zhang <[email protected]>
> ---
> .../qcom-msm8974pro-samsung-klte-common.dtsi | 812 +++++++++++++++++
> .../dts/qcom/qcom-msm8974pro-samsung-klte.dts | 813 +-----------------
> 2 files changed, 818 insertions(+), 807 deletions(-)
Why code move is not detected? It's difficult to review it. You moved
almost 100% of lines. Please use correct -B/-M/-C arguments when
generating patch and create new one with proper code move.
Best regards,
Krzysztof
On Mon, 2024-01-29 at 09:20 +0100, Krzysztof Kozlowski wrote:
> On 27/01/2024 18:21, Rong Zhang wrote:
> > Document Samsung Galaxy S5 China (kltechn) as a klte variant based on
> > msm8974pro. Also including "samsung,klte" in the compatible chain as
> > kltechn works fine with the klte DTB except for LEDs and WiFi missing.
> >
> > Signed-off-by: Rong Zhang <[email protected]>
> > ---
>
> This is a friendly reminder during the review process.
>
> It looks like you received a tag and forgot to add it.
>
> If you do not know the process, here is a short explanation:
> Please add Acked-by/Reviewed-by/Tested-by tags when posting new
> versions, under or above your Signed-off-by tag. Tag is "received", when
> provided in a message replied to you on the mailing list. Tools like b4
> can help here. However, there's no need to repost patches *only* to add
> the tags. The upstream maintainer will do that for tags received on the
> version they apply.
>
> https://elixir.bootlin.com/linux/v6.5-rc3/source/Documentation/process/submitting-patches.rst#L577
Sorry for forgetting that. I will check more precisely the next time.
> If a tag was not added on purpose, please state why and what changed.
I meant not to add your Acked-by because the dt-binding has changed
into a different form to make it consistent with the kltechn DTS. I
should have stated it but hopefully it's not too late to ask if the new
dt-binding is still eligible to receive your ACK.
Thanks,
Rong
On Mon, 2024-01-29 at 09:22 +0100, Krzysztof Kozlowski wrote:
> On 27/01/2024 18:21, Rong Zhang wrote:
> > Samsung Galaxy S5 has many variants. Variants that support LTE use klte*
> > as their codename. Currently, the only supported one is the one without
> > any suffix, namely, klte. It is known that other klte* variants have
> > only minor differences compared to klte and can mostly work with the
> > klte DTB.
> >
> > Split the common part into a common DTSI so that it can be imported in
> > the DTS of klte and other klte* variants.
> >
> > Signed-off-by: Rong Zhang <[email protected]>
> > ---
> > .../qcom-msm8974pro-samsung-klte-common.dtsi | 812 +++++++++++++++++
> > .../dts/qcom/qcom-msm8974pro-samsung-klte.dts | 813 +-----------------
> > 2 files changed, 818 insertions(+), 807 deletions(-)
>
> Why code move is not detected? It's difficult to review it. You moved
> almost 100% of lines. Please use correct -B/-M/-C arguments when
> generating patch and create new one with proper code move.
Will do in v3.
Thanks,
Rong