These patches were backported from v6.6 upstream and
are intended for 6.1.y stable kernel.
Patches have been successfully tested on the latest 6.1.75 kernel.
[PATCH 6.1.y 1/7] ASoC: codecs: es8326: Convert to i2c's .probe_new()
[PATCH 6.1.y 2/7] ASoC: codecs: ES8326: Add es8326_mute function
[PATCH 6.1.y 3/7] ASoC: codecs: ES8326: Change Hp_detect register names
[PATCH 6.1.y 4/7] ASoC: codecs: ES8326: Change Volatile Reg function
[PATCH 6.1.y 5/7] ASoC: codecs: ES8326: Fix power-up sequence
[PATCH 6.1.y 6/7] ASOC: codecs: ES8326: Add calibration support for
[PATCH 6.1.y 7/7] ASoC: codecs: ES8326: Update jact detection function
From: Zhu Ning <[email protected]>
Commit f1230a27c14b4d05e1d6af02be55c617b53728a4 upstream.
The new calibration and headphone detection function
require reading new volatile registers. Add them in
the volatile register function.
Signed-off-by: Zhu Ning <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Vasiliy Kovalev <[email protected]>
---
sound/soc/codecs/es8326.c | 23 ++++++++++++++---------
1 file changed, 14 insertions(+), 9 deletions(-)
diff --git a/sound/soc/codecs/es8326.c b/sound/soc/codecs/es8326.c
index e953c0157ba03f..7cfe535e0b6da4 100644
--- a/sound/soc/codecs/es8326.c
+++ b/sound/soc/codecs/es8326.c
@@ -158,20 +158,25 @@ static const struct snd_soc_dapm_route es8326_dapm_routes[] = {
{"HPOR", NULL, "RHPMIX"},
};
-static const struct regmap_range es8326_volatile_ranges[] = {
- regmap_reg_range(ES8326_HPDET_STA, ES8326_HPDET_STA),
-};
-
-static const struct regmap_access_table es8326_volatile_table = {
- .yes_ranges = es8326_volatile_ranges,
- .n_yes_ranges = ARRAY_SIZE(es8326_volatile_ranges),
-};
+static bool es8326_volatile_register(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case ES8326_HPL_OFFSET_INI:
+ case ES8326_HPR_OFFSET_INI:
+ case ES8326_HPDET_STA:
+ case ES8326_CTIA_OMTP_STA:
+ case ES8326_CSM_MUTE_STA:
+ return true;
+ default:
+ return false;
+ }
+}
static const struct regmap_config es8326_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
.max_register = 0xff,
- .volatile_table = &es8326_volatile_table,
+ .volatile_reg = es8326_volatile_register,
.cache_type = REGCACHE_RBTREE,
};
--
2.33.8
From: Zhu Ning <[email protected]>
Commit 04f96c9340463aae20d2511a3d6cb0b005b07d24 upstream.
The old jack detection function only supports fixed OMTP/CTIA
hardware connection. The new one supports auto OMTP/CTIA
headset detection
Signed-off-by: Zhu Ning <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Vasiliy Kovalev <[email protected]>
---
sound/soc/codecs/es8326.c | 109 +++++++++++++++++++++++++++++++-------
1 file changed, 89 insertions(+), 20 deletions(-)
diff --git a/sound/soc/codecs/es8326.c b/sound/soc/codecs/es8326.c
index 50b13296e246e1..74c03d151005d3 100644
--- a/sound/soc/codecs/es8326.c
+++ b/sound/soc/codecs/es8326.c
@@ -41,6 +41,8 @@ struct es8326_priv {
bool calibrated;
int version;
+ int hp;
+ int jack_remove_retry;
};
static const SNDRV_CTL_TLVD_DECLARE_DB_SCALE(dac_vol_tlv, -9550, 50, 0);
@@ -535,6 +537,7 @@ static void es8326_jack_button_handler(struct work_struct *work)
cur_button = SND_JACK_BTN_0;
break;
case 0x6f:
+ case 0x4b:
/* button volume up */
cur_button = SND_JACK_BTN_1;
break;
@@ -543,6 +546,7 @@ static void es8326_jack_button_handler(struct work_struct *work)
cur_button = SND_JACK_BTN_2;
break;
case 0x1e:
+ case 0xe2:
/* button released or not pressed */
cur_button = 0;
break;
@@ -552,20 +556,20 @@ static void es8326_jack_button_handler(struct work_struct *work)
if ((prev_button == cur_button) && (cur_button != 0)) {
press_count++;
- if (press_count > 10) {
- /* report a press every 500ms */
+ if (press_count > 3) {
+ /* report a press every 120ms */
snd_soc_jack_report(es8326->jack, cur_button,
SND_JACK_BTN_0 | SND_JACK_BTN_1 | SND_JACK_BTN_2);
press_count = 0;
}
button_to_report = cur_button;
queue_delayed_work(system_wq, &es8326->button_press_work,
- msecs_to_jiffies(50));
+ msecs_to_jiffies(35));
} else if (prev_button != cur_button) {
/* mismatch, detect again */
prev_button = cur_button;
queue_delayed_work(system_wq, &es8326->button_press_work,
- msecs_to_jiffies(50));
+ msecs_to_jiffies(35));
} else {
/* released or no pressed */
if (button_to_report != 0) {
@@ -589,32 +593,96 @@ static void es8326_jack_detect_handler(struct work_struct *work)
mutex_lock(&es8326->lock);
iface = snd_soc_component_read(comp, ES8326_HPDET_STA);
dev_dbg(comp->dev, "gpio flag %#04x", iface);
+
+ if (es8326->jack_remove_retry == 1) {
+ if (iface & ES8326_HPINSERT_FLAG)
+ es8326->jack_remove_retry = 2;
+ else
+ es8326->jack_remove_retry = 0;
+
+ dev_dbg(comp->dev, "remove event check, set HPJACK_POL normal, cnt = %d\n",
+ es8326->jack_remove_retry);
+ /*
+ * Inverted HPJACK_POL bit to trigger one IRQ to double check HP Removal event
+ */
+ regmap_update_bits(es8326->regmap, ES8326_HPDET_TYPE,
+ ES8326_HP_DET_JACK_POL, (es8326->jd_inverted ?
+ ~es8326->jack_pol : es8326->jack_pol));
+ goto exit;
+ }
+
if ((iface & ES8326_HPINSERT_FLAG) == 0) {
/* Jack unplugged or spurious IRQ */
- dev_dbg(comp->dev, "No headset detected");
+ dev_dbg(comp->dev, "No headset detected\n");
+ es8326_disable_micbias(es8326->component);
if (es8326->jack->status & SND_JACK_HEADPHONE) {
+ dev_dbg(comp->dev, "Report hp remove event\n");
snd_soc_jack_report(es8326->jack, 0, SND_JACK_HEADSET);
- snd_soc_component_write(comp, ES8326_ADC1_SRC, es8326->mic2_src);
- es8326_disable_micbias(comp);
+ /* mute adc when mic path switch */
+ regmap_write(es8326->regmap, ES8326_ADC_SCALE, 0x33);
+ regmap_write(es8326->regmap, ES8326_ADC1_SRC, 0x44);
+ regmap_write(es8326->regmap, ES8326_ADC2_SRC, 0x66);
+ es8326->hp = 0;
+ }
+ regmap_update_bits(es8326->regmap, ES8326_HPDET_TYPE, 0x03, 0x01);
+ /*
+ * Inverted HPJACK_POL bit to trigger one IRQ to double check HP Removal event
+ */
+ if (es8326->jack_remove_retry == 0) {
+ es8326->jack_remove_retry = 1;
+ dev_dbg(comp->dev, "remove event check, invert HPJACK_POL, cnt = %d\n",
+ es8326->jack_remove_retry);
+ regmap_update_bits(es8326->regmap, ES8326_HPDET_TYPE,
+ ES8326_HP_DET_JACK_POL, (es8326->jd_inverted ?
+ es8326->jack_pol : ~es8326->jack_pol));
+
+ } else {
+ es8326->jack_remove_retry = 0;
}
} else if ((iface & ES8326_HPINSERT_FLAG) == ES8326_HPINSERT_FLAG) {
+ es8326->jack_remove_retry = 0;
+ if (es8326->hp == 0) {
+ dev_dbg(comp->dev, "First insert, start OMTP/CTIA type check\n");
+ /*
+ * set auto-check mode, then restart jack_detect_work after 100ms.
+ * Don't report jack status.
+ */
+ regmap_update_bits(es8326->regmap, ES8326_HPDET_TYPE, 0x03, 0x01);
+ usleep_range(50000, 70000);
+ regmap_update_bits(es8326->regmap, ES8326_HPDET_TYPE, 0x03, 0x00);
+ queue_delayed_work(system_wq, &es8326->jack_detect_work,
+ msecs_to_jiffies(100));
+ es8326->hp = 1;
+ goto exit;
+ }
if (es8326->jack->status & SND_JACK_HEADSET) {
/* detect button */
+ dev_dbg(comp->dev, "button pressed\n");
queue_delayed_work(system_wq, &es8326->button_press_work, 10);
+ goto exit;
+ }
+ if ((iface & ES8326_HPBUTTON_FLAG) == 0x01) {
+ dev_dbg(comp->dev, "Headphone detected\n");
+ snd_soc_jack_report(es8326->jack,
+ SND_JACK_HEADPHONE, SND_JACK_HEADSET);
} else {
- if ((iface & ES8326_HPBUTTON_FLAG) == 0x00) {
- dev_dbg(comp->dev, "Headset detected");
- snd_soc_jack_report(es8326->jack,
- SND_JACK_HEADSET, SND_JACK_HEADSET);
- snd_soc_component_write(comp,
- ES8326_ADC1_SRC, es8326->mic1_src);
- } else {
- dev_dbg(comp->dev, "Headphone detected");
- snd_soc_jack_report(es8326->jack,
- SND_JACK_HEADPHONE, SND_JACK_HEADSET);
- }
+ dev_dbg(comp->dev, "Headset detected\n");
+ snd_soc_jack_report(es8326->jack,
+ SND_JACK_HEADSET, SND_JACK_HEADSET);
+
+ regmap_write(es8326->regmap, ES8326_ADC_SCALE, 0x33);
+ regmap_update_bits(es8326->regmap, ES8326_PGA_PDN,
+ 0x08, 0x08);
+ regmap_update_bits(es8326->regmap, ES8326_PGAGAIN,
+ 0x80, 0x80);
+ regmap_write(es8326->regmap, ES8326_ADC1_SRC, 0x00);
+ regmap_write(es8326->regmap, ES8326_ADC2_SRC, 0x00);
+ regmap_update_bits(es8326->regmap, ES8326_PGA_PDN,
+ 0x08, 0x00);
+ usleep_range(10000, 15000);
}
}
+exit:
mutex_unlock(&es8326->lock);
}
@@ -633,7 +701,7 @@ static irqreturn_t es8326_irq(int irq, void *dev_id)
msecs_to_jiffies(10));
else
queue_delayed_work(system_wq, &es8326->jack_detect_work,
- msecs_to_jiffies(300));
+ msecs_to_jiffies(600));
out:
return IRQ_HANDLED;
@@ -763,7 +831,8 @@ static int es8326_resume(struct snd_soc_component *component)
(ES8326_HP_DET_SRC_PIN9 | es8326->jack_pol) :
(ES8326_HP_DET_SRC_PIN9 | es8326->jack_pol | 0x04)));
- es8326_irq(es8326->irq, es8326);
+ es8326->jack_remove_retry = 0;
+ es8326->hp = 0;
return 0;
}
--
2.33.8
From: Uwe Kleine-König <[email protected]>
Commit 784252bac835c831e10c48be633cd1ff0d697326 upstream.
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Vasiliy Kovalev <[email protected]>
---
sound/soc/codecs/es8326.c | 5 ++---
1 file changed, 2 insertions(+), 3 deletions(-)
diff --git a/sound/soc/codecs/es8326.c b/sound/soc/codecs/es8326.c
index 555125efd9ad3f..28a0565c2a955b 100644
--- a/sound/soc/codecs/es8326.c
+++ b/sound/soc/codecs/es8326.c
@@ -816,8 +816,7 @@ static const struct snd_soc_component_driver soc_component_dev_es8326 = {
.endianness = 1,
};
-static int es8326_i2c_probe(struct i2c_client *i2c,
- const struct i2c_device_id *id)
+static int es8326_i2c_probe(struct i2c_client *i2c)
{
struct es8326_priv *es8326;
int ret;
@@ -897,7 +896,7 @@ static struct i2c_driver es8326_i2c_driver = {
.acpi_match_table = ACPI_PTR(es8326_acpi_match),
.of_match_table = of_match_ptr(es8326_of_match),
},
- .probe = es8326_i2c_probe,
+ .probe_new = es8326_i2c_probe,
.id_table = es8326_i2c_id,
};
module_i2c_driver(es8326_i2c_driver);
--
2.33.8
From: Zhu Ning <[email protected]>
Commit 4ddad00c609bdcd6635537d3acb9bd57a5fc79e6 upstream.
The old register naming method is confusing. The reg 0x57 decides
the default headset hardware connection type, and the reg 0xfb is
the headset detection status register, which changes during headset
insertion. Change the name to ES8326_HPDET_TYPE and ES8326_HPDET_STA.
Signed-off-by: Zhu Ning <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Vasiliy Kovalev <[email protected]>
---
sound/soc/codecs/es8326.c | 10 +++++-----
sound/soc/codecs/es8326.h | 12 ++++++++----
2 files changed, 13 insertions(+), 9 deletions(-)
diff --git a/sound/soc/codecs/es8326.c b/sound/soc/codecs/es8326.c
index 4399ba36aee25d..e953c0157ba03f 100644
--- a/sound/soc/codecs/es8326.c
+++ b/sound/soc/codecs/es8326.c
@@ -159,7 +159,7 @@ static const struct snd_soc_dapm_route es8326_dapm_routes[] = {
};
static const struct regmap_range es8326_volatile_ranges[] = {
- regmap_reg_range(ES8326_HP_DETECT, ES8326_HP_DETECT),
+ regmap_reg_range(ES8326_HPDET_STA, ES8326_HPDET_STA),
};
static const struct regmap_access_table es8326_volatile_table = {
@@ -519,7 +519,7 @@ static void es8326_jack_button_handler(struct work_struct *work)
return;
mutex_lock(&es8326->lock);
- iface = snd_soc_component_read(comp, ES8326_HP_DETECT);
+ iface = snd_soc_component_read(comp, ES8326_HPDET_STA);
switch (iface) {
case 0x93:
/* pause button detected */
@@ -578,7 +578,7 @@ static void es8326_jack_detect_handler(struct work_struct *work)
unsigned int iface;
mutex_lock(&es8326->lock);
- iface = snd_soc_component_read(comp, ES8326_HP_DETECT);
+ iface = snd_soc_component_read(comp, ES8326_HPDET_STA);
dev_dbg(comp->dev, "gpio flag %#04x", iface);
if ((iface & ES8326_HPINSERT_FLAG) == 0) {
/* Jack unplugged or spurious IRQ */
@@ -651,7 +651,7 @@ static int es8326_resume(struct snd_soc_component *component)
regmap_write(es8326->regmap, ES8326_ADC1_SRC, es8326->mic1_src);
regmap_write(es8326->regmap, ES8326_ADC2_SRC, es8326->mic2_src);
regmap_write(es8326->regmap, ES8326_HPJACK_TIMER, 0x88);
- regmap_write(es8326->regmap, ES8326_HP_DET,
+ regmap_write(es8326->regmap, ES8326_HPDET_TYPE,
ES8326_HP_DET_SRC_PIN9 | es8326->jack_pol);
regmap_write(es8326->regmap, ES8326_INT_SOURCE, es8326->interrupt_src);
regmap_write(es8326->regmap, ES8326_INTOUT_IO, es8326->interrupt_clk);
@@ -743,7 +743,7 @@ static void es8326_enable_jack_detect(struct snd_soc_component *component,
mutex_lock(&es8326->lock);
if (es8326->jd_inverted)
- snd_soc_component_update_bits(component, ES8326_HP_DET,
+ snd_soc_component_update_bits(component, ES8326_HPDET_TYPE,
ES8326_HP_DET_JACK_POL, ~es8326->jack_pol);
es8326->jack = jack;
diff --git a/sound/soc/codecs/es8326.h b/sound/soc/codecs/es8326.h
index 65ed4d1dc7da09..cd04d11a88d96a 100644
--- a/sound/soc/codecs/es8326.h
+++ b/sound/soc/codecs/es8326.h
@@ -73,15 +73,19 @@
#define ES8326_DRC_RECOVERY 0x53
#define ES8326_DRC_WINSIZE 0x54
#define ES8326_HPJACK_TIMER 0x56
-#define ES8326_HP_DET 0x57
+#define ES8326_HPDET_TYPE 0x57
#define ES8326_INT_SOURCE 0x58
#define ES8326_INTOUT_IO 0x59
#define ES8326_SDINOUT1_IO 0x5A
#define ES8326_SDINOUT23_IO 0x5B
#define ES8326_JACK_PULSE 0x5C
+#define ES8326_HP_MISC 0xF7
+#define ES8326_CTIA_OMTP_STA 0xF8
#define ES8326_PULLUP_CTL 0xF9
-#define ES8326_HP_DETECT 0xFB
+#define ES8326_CSM_I2C_STA 0xFA
+#define ES8326_HPDET_STA 0xFB
+#define ES8326_CSM_MUTE_STA 0xFC
#define ES8326_CHIP_ID1 0xFD
#define ES8326_CHIP_ID2 0xFE
#define ES8326_CHIP_VERSION 0xFF
@@ -146,7 +150,7 @@
#define ES8326_ADC3_SHIFT 0
#define ES8326_ADC4_SHIFT 3
-/* ES8326_HP_DET */
+/* ES8326_HPDET_TYPE */
#define ES8326_HP_DET_SRC_PIN27 (1 << 5)
#define ES8326_HP_DET_SRC_PIN9 (1 << 4)
#define ES8326_HP_DET_JACK_POL (1 << 3)
@@ -174,7 +178,7 @@
#define ES8326_SDINOUT2_SHIFT 4
#define ES8326_SDINOUT3_SHIFT 0
-/* ES8326_HP_DETECT */
+/* ES8326_HPDET_STA */
#define ES8326_HPINSERT_FLAG (1 << 1)
#define ES8326_HPBUTTON_FLAG (1 << 0)
--
2.33.8
From: Zhu Ning <[email protected]>
Commit ac20a73d765c0374f5e7b5d0f2f43c4598d69c66 upstream.
Old power-up sequence causes large pop noise during start-up.
Using a new sequence instead.
Also, the registers are now reset to default value in suspend
function.
Signed-off-by: Zhu Ning <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Vasiliy Kovalev <[email protected]>
---
sound/soc/codecs/es8326.c | 95 ++++++++++++++++++++++++++++-----------
sound/soc/codecs/es8326.h | 10 ++++-
2 files changed, 77 insertions(+), 28 deletions(-)
diff --git a/sound/soc/codecs/es8326.c b/sound/soc/codecs/es8326.c
index 7cfe535e0b6da4..1525fac1f9b8b1 100644
--- a/sound/soc/codecs/es8326.c
+++ b/sound/soc/codecs/es8326.c
@@ -638,40 +638,77 @@ static irqreturn_t es8326_irq(int irq, void *dev_id)
static int es8326_resume(struct snd_soc_component *component)
{
struct es8326_priv *es8326 = snd_soc_component_get_drvdata(component);
- unsigned int reg;
regcache_cache_only(es8326->regmap, false);
regcache_sync(es8326->regmap);
+ /* reset internal clock state */
+ regmap_write(es8326->regmap, ES8326_RESET, 0x1f);
+ regmap_write(es8326->regmap, ES8326_VMIDSEL, 0x0E);
+ usleep_range(10000, 15000);
+ regmap_write(es8326->regmap, ES8326_HPJACK_TIMER, 0x88);
+ /* set headphone default type and detect pin */
+ regmap_write(es8326->regmap, ES8326_HPDET_TYPE, 0x81);
+ regmap_write(es8326->regmap, ES8326_CLK_RESAMPLE, 0x05);
+
+ /* set internal oscillator as clock source of headpone cp */
+ regmap_write(es8326->regmap, ES8326_CLK_DIV_CPC, 0x84);
regmap_write(es8326->regmap, ES8326_CLK_CTL, ES8326_CLK_ON);
- /* Two channel ADC */
- regmap_write(es8326->regmap, ES8326_PULLUP_CTL, 0x02);
+ /* clock manager reset release */
+ regmap_write(es8326->regmap, ES8326_RESET, 0x17);
+ /* set headphone detection as half scan mode */
+ regmap_write(es8326->regmap, ES8326_HP_MISC, 0x08);
+ regmap_write(es8326->regmap, ES8326_PULLUP_CTL, 0x00);
+
+ /* enable headphone driver */
+ regmap_write(es8326->regmap, ES8326_HP_DRIVER, 0xa7);
+ usleep_range(2000, 5000);
+ regmap_write(es8326->regmap, ES8326_HP_DRIVER_REF, 0xab);
+ usleep_range(2000, 5000);
+ regmap_write(es8326->regmap, ES8326_HP_DRIVER_REF, 0xbb);
+ usleep_range(2000, 5000);
+ regmap_write(es8326->regmap, ES8326_HP_DRIVER, 0xa1);
+
regmap_write(es8326->regmap, ES8326_CLK_INV, 0x00);
- regmap_write(es8326->regmap, ES8326_CLK_DIV_CPC, 0x1F);
- regmap_write(es8326->regmap, ES8326_CLK_VMIDS1, 0xC8);
- regmap_write(es8326->regmap, ES8326_CLK_VMIDS2, 0x88);
- regmap_write(es8326->regmap, ES8326_CLK_CAL_TIME, 0x20);
+ regmap_write(es8326->regmap, ES8326_CLK_VMIDS1, 0xc4);
+ regmap_write(es8326->regmap, ES8326_CLK_VMIDS2, 0x81);
+ regmap_write(es8326->regmap, ES8326_CLK_CAL_TIME, 0x00);
+
+ /* turn off headphone out */
+ regmap_write(es8326->regmap, ES8326_HP_CAL, 0x00);
+ /* set ADC and DAC in low power mode */
+ regmap_write(es8326->regmap, ES8326_ANA_LP, 0xf0);
+
+ /* force micbias on */
+ regmap_write(es8326->regmap, ES8326_ANA_MICBIAS, 0x4f);
regmap_write(es8326->regmap, ES8326_SYS_BIAS, 0x08);
- regmap_write(es8326->regmap, ES8326_DAC2HPMIX, 0x22);
- regmap_write(es8326->regmap, ES8326_ADC1_SRC, es8326->mic1_src);
- regmap_write(es8326->regmap, ES8326_ADC2_SRC, es8326->mic2_src);
- regmap_write(es8326->regmap, ES8326_HPJACK_TIMER, 0x88);
- regmap_write(es8326->regmap, ES8326_HPDET_TYPE,
- ES8326_HP_DET_SRC_PIN9 | es8326->jack_pol);
- regmap_write(es8326->regmap, ES8326_INT_SOURCE, es8326->interrupt_src);
- regmap_write(es8326->regmap, ES8326_INTOUT_IO, es8326->interrupt_clk);
+ regmap_write(es8326->regmap, ES8326_ANA_VSEL, 0x7F);
+ /* select vdda as micbias source */
+ regmap_write(es8326->regmap, ES8326_VMIDLOW, 0x23);
+ /* set dac dsmclip = 1 */
+ regmap_write(es8326->regmap, ES8326_DAC_DSM, 0x08);
+ regmap_write(es8326->regmap, ES8326_DAC_VPPSCALE, 0x15);
+
+ regmap_write(es8326->regmap, ES8326_INT_SOURCE,
+ (ES8326_INT_SRC_PIN9 | ES8326_INT_SRC_BUTTON));
+ regmap_write(es8326->regmap, ES8326_INTOUT_IO,
+ es8326->interrupt_clk);
+ regmap_write(es8326->regmap, ES8326_SDINOUT1_IO,
+ (ES8326_IO_DMIC_CLK << ES8326_SDINOUT1_SHIFT));
+ regmap_write(es8326->regmap, ES8326_SDINOUT23_IO, ES8326_IO_INPUT);
+
+ regmap_write(es8326->regmap, ES8326_ANA_PDN, 0x3b);
regmap_write(es8326->regmap, ES8326_RESET, ES8326_CSM_ON);
- snd_soc_component_update_bits(component, ES8326_PGAGAIN,
- ES8326_MIC_SEL_MASK, ES8326_MIC1_SEL);
-
- regmap_read(es8326->regmap, ES8326_CHIP_VERSION, ®);
- if ((reg & ES8326_VERSION_B) == 1) {
- regmap_write(es8326->regmap, ES8326_ANA_MICBIAS, 0xDD);
- regmap_write(es8326->regmap, ES8326_ANA_VSEL, 0x7F);
- regmap_write(es8326->regmap, ES8326_VMIDLOW, 0x0F);
- /* enable button detect */
- regmap_write(es8326->regmap, ES8326_HP_DRIVER, 0xA0);
- }
+ regmap_update_bits(es8326->regmap, ES8326_PGAGAIN, ES8326_MIC_SEL_MASK,
+ ES8326_MIC1_SEL);
+
+ regmap_update_bits(es8326->regmap, ES8326_DAC_MUTE, ES8326_MUTE_MASK,
+ ES8326_MUTE);
+
+ regmap_write(es8326->regmap, ES8326_HPDET_TYPE, 0x80 |
+ ((es8326->version == ES8326_VERSION_B) ?
+ (ES8326_HP_DET_SRC_PIN9 | es8326->jack_pol) :
+ (ES8326_HP_DET_SRC_PIN9 | es8326->jack_pol | 0x04)));
es8326_irq(es8326->irq, es8326);
return 0;
@@ -688,6 +725,10 @@ static int es8326_suspend(struct snd_soc_component *component)
regcache_cache_only(es8326->regmap, true);
regcache_mark_dirty(es8326->regmap);
+ /* reset register value to default */
+ regmap_write(es8326->regmap, ES8326_CSM_I2C_STA, 0x01);
+ usleep_range(1000, 3000);
+ regmap_write(es8326->regmap, ES8326_CSM_I2C_STA, 0x00);
return 0;
}
@@ -717,7 +758,7 @@ static int es8326_probe(struct snd_soc_component *component)
ret = device_property_read_u8(component->dev, "everest,jack-pol", &es8326->jack_pol);
if (ret != 0) {
dev_dbg(component->dev, "jack-pol return %d", ret);
- es8326->jack_pol = ES8326_HP_DET_BUTTON_POL | ES8326_HP_TYPE_OMTP;
+ es8326->jack_pol = ES8326_HP_TYPE_AUTO;
}
dev_dbg(component->dev, "jack-pol %x", es8326->jack_pol);
diff --git a/sound/soc/codecs/es8326.h b/sound/soc/codecs/es8326.h
index cd04d11a88d96a..90a08351d6acd0 100644
--- a/sound/soc/codecs/es8326.h
+++ b/sound/soc/codecs/es8326.h
@@ -160,6 +160,13 @@
#define ES8326_HP_TYPE_AUTO (1 << 0)
#define ES8326_HP_TYPE_AUTO_INV (0 << 0)
+/* ES8326_INT_SOURCE */
+#define ES8326_INT_SRC_DAC_MOZ (1 << 0)
+#define ES8326_INT_SRC_ADC_MOZ (1 << 1)
+#define ES8326_INT_SRC_BUTTON (1 << 2)
+#define ES8326_INT_SRC_PIN9 (1 << 3)
+#define ES8326_INT_SRC_PIN27 (1 << 4)
+
/* ES8326_SDINOUT1_IO */
#define ES8326_IO_INPUT (0 << 0)
#define ES8326_IO_SDIN_SLOT0 (1 << 0)
@@ -183,6 +190,7 @@
#define ES8326_HPBUTTON_FLAG (1 << 0)
/* ES8326_CHIP_VERSION 0xFF */
-#define ES8326_VERSION_B (1 << 0)
+#define ES8326_VERSION (1 << 0)
+#define ES8326_VERSION_B (3 << 0)
#endif
--
2.33.8
From: Zhu Ning <[email protected]>
Commit 083912c240de0c5f797da0443f5a99e87b75fcb3 upstream.
The internal analog power and hp Vref of es8326 should always be on to
reduce pop noise. The HP_VOL and HP_CAL are moved to es8326_mute function
so they are turned on at last and turned off at first.
Also, the calibration should be done manually once during start-up
to reduce DC offset on headphone.
Signed-off-by: Zhu Ning <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Vasiliy Kovalev <[email protected]>
---
sound/soc/codecs/es8326.c | 75 ++++++++++++++++-----------------------
sound/soc/codecs/es8326.h | 8 +++--
2 files changed, 36 insertions(+), 47 deletions(-)
diff --git a/sound/soc/codecs/es8326.c b/sound/soc/codecs/es8326.c
index 28a0565c2a955b..4399ba36aee25d 100644
--- a/sound/soc/codecs/es8326.c
+++ b/sound/soc/codecs/es8326.c
@@ -38,6 +38,9 @@ struct es8326_priv {
u8 interrupt_clk;
bool jd_inverted;
unsigned int sysclk;
+
+ bool calibrated;
+ int version;
};
static const SNDRV_CTL_TLVD_DECLARE_DB_SCALE(dac_vol_tlv, -9550, 50, 0);
@@ -121,33 +124,12 @@ static const struct snd_soc_dapm_widget es8326_dapm_widgets[] = {
/* Analog Power Supply*/
SND_SOC_DAPM_DAC("Right DAC", NULL, ES8326_ANA_PDN, 0, 1),
SND_SOC_DAPM_DAC("Left DAC", NULL, ES8326_ANA_PDN, 1, 1),
- SND_SOC_DAPM_SUPPLY("Analog Power", ES8326_ANA_PDN, 7, 1, NULL, 0),
- SND_SOC_DAPM_SUPPLY("IBias Power", ES8326_ANA_PDN, 6, 1, NULL, 0),
- SND_SOC_DAPM_SUPPLY("ADC Vref", ES8326_ANA_PDN, 5, 1, NULL, 0),
- SND_SOC_DAPM_SUPPLY("DAC Vref", ES8326_ANA_PDN, 4, 1, NULL, 0),
- SND_SOC_DAPM_SUPPLY("Vref Power", ES8326_ANA_PDN, 3, 1, NULL, 0),
SND_SOC_DAPM_SUPPLY("MICBIAS1", ES8326_ANA_MICBIAS, 2, 0, NULL, 0),
SND_SOC_DAPM_SUPPLY("MICBIAS2", ES8326_ANA_MICBIAS, 3, 0, NULL, 0),
SND_SOC_DAPM_PGA("LHPMIX", ES8326_DAC2HPMIX, 7, 0, NULL, 0),
SND_SOC_DAPM_PGA("RHPMIX", ES8326_DAC2HPMIX, 3, 0, NULL, 0),
- /* Headphone Charge Pump and Output */
- SND_SOC_DAPM_SUPPLY("HPOR Cal", ES8326_HP_CAL, 7, 1, NULL, 0),
- SND_SOC_DAPM_SUPPLY("HPOL Cal", ES8326_HP_CAL, 3, 1, NULL, 0),
- SND_SOC_DAPM_SUPPLY("Headphone Charge Pump", ES8326_HP_DRIVER,
- 3, 1, NULL, 0),
- SND_SOC_DAPM_SUPPLY("Headphone Driver Bias", ES8326_HP_DRIVER,
- 2, 1, NULL, 0),
- SND_SOC_DAPM_SUPPLY("Headphone LDO", ES8326_HP_DRIVER,
- 1, 1, NULL, 0),
- SND_SOC_DAPM_SUPPLY("Headphone Reference", ES8326_HP_DRIVER,
- 0, 1, NULL, 0),
- SND_SOC_DAPM_REG(snd_soc_dapm_supply, "HPOR Supply", ES8326_HP_CAL,
- ES8326_HPOR_SHIFT, 7, 7, 0),
- SND_SOC_DAPM_REG(snd_soc_dapm_supply, "HPOL Supply", ES8326_HP_CAL,
- 0, 7, 7, 0),
-
SND_SOC_DAPM_OUTPUT("HPOL"),
SND_SOC_DAPM_OUTPUT("HPOR"),
};
@@ -166,34 +148,12 @@ static const struct snd_soc_dapm_route es8326_dapm_routes[] = {
{"I2S OUT", NULL, "ADC L"},
{"I2S OUT", NULL, "ADC R"},
- {"I2S OUT", NULL, "Analog Power"},
- {"I2S OUT", NULL, "ADC Vref"},
- {"I2S OUT", NULL, "Vref Power"},
- {"I2S OUT", NULL, "IBias Power"},
- {"I2S IN", NULL, "Analog Power"},
- {"I2S IN", NULL, "DAC Vref"},
- {"I2S IN", NULL, "Vref Power"},
- {"I2S IN", NULL, "IBias Power"},
-
{"Right DAC", NULL, "I2S IN"},
{"Left DAC", NULL, "I2S IN"},
{"LHPMIX", NULL, "Left DAC"},
{"RHPMIX", NULL, "Right DAC"},
- {"HPOR", NULL, "HPOR Cal"},
- {"HPOL", NULL, "HPOL Cal"},
- {"HPOR", NULL, "HPOR Supply"},
- {"HPOL", NULL, "HPOL Supply"},
- {"HPOL", NULL, "Headphone Charge Pump"},
- {"HPOR", NULL, "Headphone Charge Pump"},
- {"HPOL", NULL, "Headphone Driver Bias"},
- {"HPOR", NULL, "Headphone Driver Bias"},
- {"HPOL", NULL, "Headphone LDO"},
- {"HPOR", NULL, "Headphone LDO"},
- {"HPOL", NULL, "Headphone Reference"},
- {"HPOR", NULL, "Headphone Reference"},
-
{"HPOL", NULL, "LHPMIX"},
{"HPOR", NULL, "RHPMIX"},
};
@@ -419,6 +379,31 @@ static int es8326_pcm_hw_params(struct snd_pcm_substream *substream,
return 0;
}
+static int es8326_mute(struct snd_soc_dai *dai, int mute, int direction)
+{
+ struct snd_soc_component *component = dai->component;
+ struct es8326_priv *es8326 = snd_soc_component_get_drvdata(component);
+
+ if (mute) {
+ regmap_write(es8326->regmap, ES8326_HP_CAL, ES8326_HP_OFF);
+ regmap_update_bits(es8326->regmap, ES8326_DAC_MUTE,
+ ES8326_MUTE_MASK, ES8326_MUTE);
+ regmap_write(es8326->regmap, ES8326_HP_DRIVER, 0xf0);
+ } else {
+ if (!es8326->calibrated) {
+ regmap_write(es8326->regmap, ES8326_HP_CAL, ES8326_HP_FORCE_CAL);
+ msleep(30);
+ es8326->calibrated = true;
+ }
+ regmap_write(es8326->regmap, ES8326_HP_DRIVER, 0xa0);
+ regmap_write(es8326->regmap, ES8326_HP_VOL, 0x00);
+ regmap_write(es8326->regmap, ES8326_HP_CAL, ES8326_HP_ON);
+ regmap_update_bits(es8326->regmap, ES8326_DAC_MUTE,
+ ES8326_MUTE_MASK, ~(ES8326_MUTE));
+ }
+ return 0;
+}
+
static int es8326_set_bias_level(struct snd_soc_component *codec,
enum snd_soc_bias_level level)
{
@@ -469,6 +454,8 @@ static const struct snd_soc_dai_ops es8326_ops = {
.hw_params = es8326_pcm_hw_params,
.set_fmt = es8326_set_dai_fmt,
.set_sysclk = es8326_set_dai_sysclk,
+ .mute_stream = es8326_mute,
+ .no_capture_mute = 1,
};
static struct snd_soc_dai_driver es8326_dai = {
@@ -691,7 +678,7 @@ static int es8326_suspend(struct snd_soc_component *component)
cancel_delayed_work_sync(&es8326->jack_detect_work);
es8326_disable_micbias(component);
-
+ es8326->calibrated = false;
regmap_write(es8326->regmap, ES8326_CLK_CTL, ES8326_CLK_OFF);
regcache_cache_only(es8326->regmap, true);
regcache_mark_dirty(es8326->regmap);
diff --git a/sound/soc/codecs/es8326.h b/sound/soc/codecs/es8326.h
index 8e5ffe5ee10da3..65ed4d1dc7da09 100644
--- a/sound/soc/codecs/es8326.h
+++ b/sound/soc/codecs/es8326.h
@@ -9,8 +9,6 @@
#ifndef _ES8326_H
#define _ES8326_H
-#define CONFIG_HHTECH_MINIPMP 1
-
/* ES8326 register space */
#define ES8326_RESET 0x00
#define ES8326_CLK_CTL 0x01
@@ -94,6 +92,8 @@
#define ES8326_PWRUP_SEQ_EN (1 << 5)
#define ES8326_CODEC_RESET (0x0f << 0)
#define ES8326_CSM_OFF (0 << 7)
+#define ES8326_MUTE_MASK (3 << 0)
+#define ES8326_MUTE (3 << 0)
/* ES8326_CLK_CTL */
#define ES8326_CLK_ON (0x7f << 0)
@@ -122,7 +122,9 @@
#define ES8326_MIC2_SEL (1 << 5)
/* ES8326_HP_CAL */
-#define ES8326_HPOR_SHIFT 4
+#define ES8326_HP_OFF 0
+#define ES8326_HP_FORCE_CAL ((1 << 7) | (1 << 3))
+#define ES8326_HP_ON ((7 << 4) | (7 << 0))
/* ES8326_ADC1_SRC */
#define ES8326_ADC1_SHIFT 0
--
2.33.8
From: Zhu Ning <[email protected]>
Commit 0663286e58e6f611f3578b5e63e1faa576d139fd upstream.
Version_b requires a new way of calibrating headset offset. A new
calibration function is added.
Signed-off-by: Zhu Ning <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Vasiliy Kovalev <[email protected]>
---
sound/soc/codecs/es8326.c | 83 ++++++++++++++++++++++++++++++++-------
1 file changed, 68 insertions(+), 15 deletions(-)
diff --git a/sound/soc/codecs/es8326.c b/sound/soc/codecs/es8326.c
index 1525fac1f9b8b1..50b13296e246e1 100644
--- a/sound/soc/codecs/es8326.c
+++ b/sound/soc/codecs/es8326.c
@@ -388,6 +388,7 @@ static int es8326_mute(struct snd_soc_dai *dai, int mute, int direction)
{
struct snd_soc_component *component = dai->component;
struct es8326_priv *es8326 = snd_soc_component_get_drvdata(component);
+ unsigned int offset_l, offset_r;
if (mute) {
regmap_write(es8326->regmap, ES8326_HP_CAL, ES8326_HP_OFF);
@@ -398,10 +399,16 @@ static int es8326_mute(struct snd_soc_dai *dai, int mute, int direction)
if (!es8326->calibrated) {
regmap_write(es8326->regmap, ES8326_HP_CAL, ES8326_HP_FORCE_CAL);
msleep(30);
+ regmap_write(es8326->regmap, ES8326_HP_CAL, ES8326_HP_OFF);
+ regmap_read(es8326->regmap, ES8326_HPL_OFFSET_INI, &offset_l);
+ regmap_read(es8326->regmap, ES8326_HPR_OFFSET_INI, &offset_r);
+ regmap_write(es8326->regmap, ES8326_HP_OFFSET_CAL, 0x8c);
+ regmap_write(es8326->regmap, ES8326_HPL_OFFSET_INI, offset_l);
+ regmap_write(es8326->regmap, ES8326_HPR_OFFSET_INI, offset_r);
es8326->calibrated = true;
}
regmap_write(es8326->regmap, ES8326_HP_DRIVER, 0xa0);
- regmap_write(es8326->regmap, ES8326_HP_VOL, 0x00);
+ regmap_write(es8326->regmap, ES8326_HP_VOL, 0x80);
regmap_write(es8326->regmap, ES8326_HP_CAL, ES8326_HP_ON);
regmap_update_bits(es8326->regmap, ES8326_DAC_MUTE,
ES8326_MUTE_MASK, ~(ES8326_MUTE));
@@ -420,15 +427,17 @@ static int es8326_set_bias_level(struct snd_soc_component *codec,
ret = clk_prepare_enable(es8326->mclk);
if (ret)
return ret;
- regmap_write(es8326->regmap, ES8326_RESET, ES8326_PWRUP_SEQ_EN);
- regmap_write(es8326->regmap, ES8326_INTOUT_IO, 0x45);
+
+ regmap_write(es8326->regmap, ES8326_RESET, 0x9f);
+ msleep(20);
+ regmap_update_bits(es8326->regmap, ES8326_DAC_DSM, 0x01, 0x00);
+ regmap_write(es8326->regmap, ES8326_INTOUT_IO, es8326->interrupt_clk);
regmap_write(es8326->regmap, ES8326_SDINOUT1_IO,
(ES8326_IO_DMIC_CLK << ES8326_SDINOUT1_SHIFT));
- regmap_write(es8326->regmap, ES8326_SDINOUT23_IO, ES8326_IO_INPUT);
- regmap_write(es8326->regmap, ES8326_CLK_RESAMPLE, 0x05);
- regmap_write(es8326->regmap, ES8326_VMIDSEL, 0x02);
+ regmap_write(es8326->regmap, ES8326_VMIDSEL, 0x0E);
regmap_write(es8326->regmap, ES8326_PGA_PDN, 0x40);
- regmap_write(es8326->regmap, ES8326_DAC2HPMIX, 0xAA);
+ regmap_write(es8326->regmap, ES8326_ANA_PDN, 0x00);
+ regmap_update_bits(es8326->regmap, ES8326_CLK_CTL, 0x20, 0x20);
regmap_write(es8326->regmap, ES8326_RESET, ES8326_CSM_ON);
break;
case SND_SOC_BIAS_PREPARE:
@@ -437,15 +446,10 @@ static int es8326_set_bias_level(struct snd_soc_component *codec,
break;
case SND_SOC_BIAS_OFF:
clk_disable_unprepare(es8326->mclk);
- regmap_write(es8326->regmap, ES8326_DAC2HPMIX, 0x11);
- regmap_write(es8326->regmap, ES8326_RESET, ES8326_CSM_OFF);
- regmap_write(es8326->regmap, ES8326_PGA_PDN, 0xF8);
+ regmap_write(es8326->regmap, ES8326_ANA_PDN, 0x3b);
regmap_write(es8326->regmap, ES8326_VMIDSEL, 0x00);
- regmap_write(es8326->regmap, ES8326_INT_SOURCE, 0x08);
+ regmap_update_bits(es8326->regmap, ES8326_CLK_CTL, 0x20, 0x00);
regmap_write(es8326->regmap, ES8326_SDINOUT1_IO, ES8326_IO_INPUT);
- regmap_write(es8326->regmap, ES8326_SDINOUT23_IO, ES8326_IO_INPUT);
- regmap_write(es8326->regmap, ES8326_RESET,
- ES8326_CODEC_RESET | ES8326_PWRUP_SEQ_EN);
break;
}
@@ -635,6 +639,54 @@ static irqreturn_t es8326_irq(int irq, void *dev_id)
return IRQ_HANDLED;
}
+static int es8326_calibrate(struct snd_soc_component *component)
+{
+ struct es8326_priv *es8326 = snd_soc_component_get_drvdata(component);
+ unsigned int reg;
+ unsigned int offset_l, offset_r;
+
+ regmap_read(es8326->regmap, ES8326_CHIP_VERSION, ®);
+ es8326->version = reg;
+
+ if ((es8326->version == ES8326_VERSION_B) && (es8326->calibrated == false)) {
+ dev_dbg(component->dev, "ES8326_VERSION_B, calibrating\n");
+ regmap_write(es8326->regmap, ES8326_CLK_INV, 0xc0);
+ regmap_write(es8326->regmap, ES8326_CLK_DIV1, 0x01);
+ regmap_write(es8326->regmap, ES8326_CLK_DLL, 0x30);
+ regmap_write(es8326->regmap, ES8326_CLK_MUX, 0xed);
+ regmap_write(es8326->regmap, ES8326_CLK_TRI, 0xc1);
+ regmap_write(es8326->regmap, ES8326_DAC_MUTE, 0x03);
+ regmap_write(es8326->regmap, ES8326_ANA_VSEL, 0x7f);
+ regmap_write(es8326->regmap, ES8326_VMIDLOW, 0x33);
+ regmap_write(es8326->regmap, ES8326_DAC2HPMIX, 0x88);
+ regmap_write(es8326->regmap, ES8326_HP_VOL, 0x80);
+ regmap_write(es8326->regmap, ES8326_HP_OFFSET_CAL, 0x8c);
+ regmap_write(es8326->regmap, ES8326_RESET, 0xc0);
+ usleep_range(15000, 20000);
+
+ regmap_write(es8326->regmap, ES8326_HP_OFFSET_CAL, ES8326_HP_OFF);
+ regmap_read(es8326->regmap, ES8326_CSM_MUTE_STA, ®);
+ if ((reg & 0xf0) != 0x40)
+ msleep(50);
+
+ regmap_write(es8326->regmap, ES8326_HP_CAL, 0xd4);
+ msleep(200);
+ regmap_write(es8326->regmap, ES8326_HP_CAL, 0x4d);
+ msleep(200);
+ regmap_write(es8326->regmap, ES8326_HP_CAL, ES8326_HP_OFF);
+ regmap_read(es8326->regmap, ES8326_HPL_OFFSET_INI, &offset_l);
+ regmap_read(es8326->regmap, ES8326_HPR_OFFSET_INI, &offset_r);
+ regmap_write(es8326->regmap, ES8326_HP_OFFSET_CAL, 0x8c);
+ regmap_write(es8326->regmap, ES8326_HPL_OFFSET_INI, offset_l);
+ regmap_write(es8326->regmap, ES8326_HPR_OFFSET_INI, offset_r);
+ regmap_write(es8326->regmap, ES8326_CLK_INV, 0x00);
+
+ es8326->calibrated = true;
+ }
+
+ return 0;
+}
+
static int es8326_resume(struct snd_soc_component *component)
{
struct es8326_priv *es8326 = snd_soc_component_get_drvdata(component);
@@ -673,7 +725,8 @@ static int es8326_resume(struct snd_soc_component *component)
regmap_write(es8326->regmap, ES8326_CLK_VMIDS1, 0xc4);
regmap_write(es8326->regmap, ES8326_CLK_VMIDS2, 0x81);
regmap_write(es8326->regmap, ES8326_CLK_CAL_TIME, 0x00);
-
+ /* calibrate for B version */
+ es8326_calibrate(component);
/* turn off headphone out */
regmap_write(es8326->regmap, ES8326_HP_CAL, 0x00);
/* set ADC and DAC in low power mode */
--
2.33.8
On Tue, Jan 30, 2024 at 12:47:02PM +0300, [email protected] wrote:
> From: Uwe Kleine-K?nig <[email protected]>
>
> Commit 784252bac835c831e10c48be633cd1ff0d697326 upstream.
>
> The probe function doesn't make use of the i2c_device_id * parameter so it
> can be trivially converted.
This is obviously not a bug fix.
On Tue, Jan 30, 2024 at 12:47:01PM +0300, [email protected] wrote:
> These patches were backported from v6.6 upstream and
> are intended for 6.1.y stable kernel.
>
> Patches have been successfully tested on the latest 6.1.75 kernel.
>
> [PATCH 6.1.y 1/7] ASoC: codecs: es8326: Convert to i2c's .probe_new()
> [PATCH 6.1.y 2/7] ASoC: codecs: ES8326: Add es8326_mute function
> [PATCH 6.1.y 3/7] ASoC: codecs: ES8326: Change Hp_detect register names
> [PATCH 6.1.y 4/7] ASoC: codecs: ES8326: Change Volatile Reg function
> [PATCH 6.1.y 5/7] ASoC: codecs: ES8326: Fix power-up sequence
> [PATCH 6.1.y 6/7] ASOC: codecs: ES8326: Add calibration support for
> [PATCH 6.1.y 7/7] ASoC: codecs: ES8326: Update jact detection function
>
>
What exactly is being "fixed" here? Was the driver not working properly
in 5.15? What broke in 6.1? Or has this hardware just never worked?
These all don't seem to be fixes, so what is the need for these?
confused,
greg k-h
On Fri, Feb 02, 2024 at 05:13:50PM -0800, Greg KH wrote:
> On Tue, Jan 30, 2024 at 12:47:01PM +0300, [email protected] wrote:
> > These patches were backported from v6.6 upstream and
> > are intended for 6.1.y stable kernel.
> >
> > Patches have been successfully tested on the latest 6.1.75 kernel.
> >
> > [PATCH 6.1.y 1/7] ASoC: codecs: es8326: Convert to i2c's .probe_new()
> > [PATCH 6.1.y 2/7] ASoC: codecs: ES8326: Add es8326_mute function
> > [PATCH 6.1.y 3/7] ASoC: codecs: ES8326: Change Hp_detect register names
> > [PATCH 6.1.y 4/7] ASoC: codecs: ES8326: Change Volatile Reg function
> > [PATCH 6.1.y 5/7] ASoC: codecs: ES8326: Fix power-up sequence
> > [PATCH 6.1.y 6/7] ASOC: codecs: ES8326: Add calibration support for
> > [PATCH 6.1.y 7/7] ASoC: codecs: ES8326: Update jact detection function
> >
> >
>
> What exactly is being "fixed" here? Was the driver not working properly
> in 5.15? What broke in 6.1? Or has this hardware just never worked?
>
> These all don't seem to be fixes, so what is the need for these?
Dropped from my queues due to lack of response :(