The code in qcom_q6v5_init() requests the "wdog" IRQ as
IRQF_TRIGGER_RISING. If dt defines the interrupt type as LEVEL_HIGH then
the driver will have issues getting the IRQ again after probe deferral
with an error like:
irq: type mismatch, failed to map hwirq-14 for interrupt-controller@b220000!
Fix that by updating the devicetrees to use IRQ_TYPE_EDGE_RISING for
these interrupts, as is already used in most dt's. Also the driver was
already using the interrupts with that type.
Signed-off-by: Luca Weiss <[email protected]>
---
See also this thread:
https://lore.kernel.org/linux-arm-msm/[email protected]/
---
arch/arm64/boot/dts/qcom/sc7280.dtsi | 4 ++--
arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 6 +++---
arch/arm64/boot/dts/qcom/sm6350.dtsi | 4 ++--
arch/arm64/boot/dts/qcom/sm6375.dtsi | 2 +-
arch/arm64/boot/dts/qcom/sm8250.dtsi | 6 +++---
5 files changed, 11 insertions(+), 11 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index c31a09bac4ed..8379ca283d52 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -3707,7 +3707,7 @@ remoteproc_adsp: remoteproc@3700000 {
compatible = "qcom,sc7280-adsp-pas";
reg = <0 0x03700000 0 0x100>;
- interrupts-extended = <&pdc 6 IRQ_TYPE_LEVEL_HIGH>,
+ interrupts-extended = <&pdc 6 IRQ_TYPE_EDGE_RISING>,
<&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
<&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
<&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
@@ -3944,7 +3944,7 @@ remoteproc_cdsp: remoteproc@a300000 {
compatible = "qcom,sc7280-cdsp-pas";
reg = <0 0x0a300000 0 0x10000>;
- interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>,
+ interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>,
<&cdsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
<&cdsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
<&cdsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
index a5b194813079..c9058c7fc1a3 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
@@ -2641,7 +2641,7 @@ remoteproc_adsp: remoteproc@3000000 {
compatible = "qcom,sc8280xp-adsp-pas";
reg = <0 0x03000000 0 0x100>;
- interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
+ interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
@@ -4977,7 +4977,7 @@ remoteproc_nsp0: remoteproc@1b300000 {
compatible = "qcom,sc8280xp-nsp0-pas";
reg = <0 0x1b300000 0 0x100>;
- interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>,
+ interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>,
<&smp2p_nsp0_in 0 IRQ_TYPE_EDGE_RISING>,
<&smp2p_nsp0_in 1 IRQ_TYPE_EDGE_RISING>,
<&smp2p_nsp0_in 2 IRQ_TYPE_EDGE_RISING>,
@@ -5108,7 +5108,7 @@ remoteproc_nsp1: remoteproc@21300000 {
compatible = "qcom,sc8280xp-nsp1-pas";
reg = <0 0x21300000 0 0x100>;
- interrupts-extended = <&intc GIC_SPI 887 IRQ_TYPE_LEVEL_HIGH>,
+ interrupts-extended = <&intc GIC_SPI 887 IRQ_TYPE_EDGE_RISING>,
<&smp2p_nsp1_in 0 IRQ_TYPE_EDGE_RISING>,
<&smp2p_nsp1_in 1 IRQ_TYPE_EDGE_RISING>,
<&smp2p_nsp1_in 2 IRQ_TYPE_EDGE_RISING>,
diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 24bcec3366ef..0be053555602 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -1252,7 +1252,7 @@ adsp: remoteproc@3000000 {
compatible = "qcom,sm6350-adsp-pas";
reg = <0 0x03000000 0 0x100>;
- interrupts-extended = <&pdc 6 IRQ_TYPE_LEVEL_HIGH>,
+ interrupts-extended = <&pdc 6 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
@@ -1511,7 +1511,7 @@ cdsp: remoteproc@8300000 {
compatible = "qcom,sm6350-cdsp-pas";
reg = <0 0x08300000 0 0x10000>;
- interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>,
+ interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>,
<&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
<&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
<&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
diff --git a/arch/arm64/boot/dts/qcom/sm6375.dtsi b/arch/arm64/boot/dts/qcom/sm6375.dtsi
index 4386f8a9c636..f40509d91bbd 100644
--- a/arch/arm64/boot/dts/qcom/sm6375.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6375.dtsi
@@ -1561,7 +1561,7 @@ remoteproc_adsp: remoteproc@a400000 {
compatible = "qcom,sm6375-adsp-pas";
reg = <0 0x0a400000 0 0x100>;
- interrupts-extended = <&intc GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+ interrupts-extended = <&intc GIC_SPI 282 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index f3c70b87efad..03c7dda1d542 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -3062,7 +3062,7 @@ slpi: remoteproc@5c00000 {
compatible = "qcom,sm8250-slpi-pas";
reg = <0 0x05c00000 0 0x4000>;
- interrupts-extended = <&pdc 9 IRQ_TYPE_LEVEL_HIGH>,
+ interrupts-extended = <&pdc 9 IRQ_TYPE_EDGE_RISING>,
<&smp2p_slpi_in 0 IRQ_TYPE_EDGE_RISING>,
<&smp2p_slpi_in 1 IRQ_TYPE_EDGE_RISING>,
<&smp2p_slpi_in 2 IRQ_TYPE_EDGE_RISING>,
@@ -3766,7 +3766,7 @@ cdsp: remoteproc@8300000 {
compatible = "qcom,sm8250-cdsp-pas";
reg = <0 0x08300000 0 0x10000>;
- interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>,
+ interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>,
<&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
<&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
<&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
@@ -5928,7 +5928,7 @@ adsp: remoteproc@17300000 {
compatible = "qcom,sm8250-adsp-pas";
reg = <0 0x17300000 0 0x100>;
- interrupts-extended = <&pdc 6 IRQ_TYPE_LEVEL_HIGH>,
+ interrupts-extended = <&pdc 6 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
---
base-commit: 35a4fdde2466b9d90af297f249436a270ef9d30e
change-id: 20240219-remoteproc-irqs-63f3293af260
Best regards,
--
Luca Weiss <[email protected]>
On Mon, 19 Feb 2024 15:33:27 +0100, Luca Weiss wrote:
> The code in qcom_q6v5_init() requests the "wdog" IRQ as
> IRQF_TRIGGER_RISING. If dt defines the interrupt type as LEVEL_HIGH then
> the driver will have issues getting the IRQ again after probe deferral
> with an error like:
>
> irq: type mismatch, failed to map hwirq-14 for interrupt-controller@b220000!
>
> [...]
Applied, thanks!
[1/1] arm64: dts: qcom: Fix type of "wdog" IRQs for remoteprocs
commit: dd6943ef8edde3c6b8aee06cb142c9a41086e3b3
Best regards,
--
Bjorn Andersson <[email protected]>