According to the datasheet of BMP38x and BMP390 devices, for an SPI
read operation the first byte that is returned needs to be dropped,
and the rest of the bytes are the actual data returned from the
sensor.
Fixes: 8d329309184d ("iio: pressure: bmp280: Add support for BMP380 sensor family")
Signed-off-by: Vasileios Amoiridis <[email protected]>
---
drivers/iio/pressure/bmp280-spi.c | 49 ++++++++++++++++++++++++++++++-
1 file changed, 48 insertions(+), 1 deletion(-)
diff --git a/drivers/iio/pressure/bmp280-spi.c b/drivers/iio/pressure/bmp280-spi.c
index e8a5fed07e88..1972014dca93 100644
--- a/drivers/iio/pressure/bmp280-spi.c
+++ b/drivers/iio/pressure/bmp280-spi.c
@@ -8,6 +8,7 @@
#include <linux/spi/spi.h>
#include <linux/err.h>
#include <linux/regmap.h>
+#include <linux/bits.h>
#include "bmp280.h"
@@ -35,6 +36,33 @@ static int bmp280_regmap_spi_read(void *context, const void *reg,
return spi_write_then_read(spi, reg, reg_size, val, val_size);
}
+static int bmp380_regmap_spi_read(void *context, const void *reg,
+ size_t reg_size, void *val, size_t val_size)
+{
+ struct spi_device *spi = to_spi_device(context);
+ u8 rx_buf[4];
+ ssize_t status;
+
+ /*
+ * Maximum number of consecutive bytes read for a temperature or
+ * pressure measurement is 3.
+ */
+ if (val_size > 3)
+ return -EINVAL;
+ /*
+ * According to the BMP3xx datasheets, for a basic SPI read opertion,
+ * the first byte needs to be dropped and the rest are the requested
+ * data.
+ */
+ status = spi_write_then_read(spi, reg, 1, rx_buf, val_size + 1);
+ if (status)
+ return status;
+
+ memcpy(val, rx_buf + 1, val_size);
+
+ return 0;
+}
+
static struct regmap_bus bmp280_regmap_bus = {
.write = bmp280_regmap_spi_write,
.read = bmp280_regmap_spi_read,
@@ -42,10 +70,19 @@ static struct regmap_bus bmp280_regmap_bus = {
.val_format_endian_default = REGMAP_ENDIAN_BIG,
};
+static struct regmap_bus bmp380_regmap_bus = {
+ .write = bmp280_regmap_spi_write,
+ .read = bmp380_regmap_spi_read,
+ .read_flag_mask = BIT(7),
+ .reg_format_endian_default = REGMAP_ENDIAN_BIG,
+ .val_format_endian_default = REGMAP_ENDIAN_BIG,
+};
+
static int bmp280_spi_probe(struct spi_device *spi)
{
const struct spi_device_id *id = spi_get_device_id(spi);
const struct bmp280_chip_info *chip_info;
+ struct regmap_bus *bmp_regmap_bus;
struct regmap *regmap;
int ret;
@@ -58,8 +95,18 @@ static int bmp280_spi_probe(struct spi_device *spi)
chip_info = spi_get_device_match_data(spi);
+ switch (chip_info->chip_id[0]) {
+ case BMP380_CHIP_ID:
+ case BMP390_CHIP_ID:
+ bmp_regmap_bus = &bmp380_regmap_bus;
+ break;
+ default:
+ bmp_regmap_bus = &bmp280_regmap_bus;
+ break;
+ }
+
regmap = devm_regmap_init(&spi->dev,
- &bmp280_regmap_bus,
+ bmp_regmap_bus,
&spi->dev,
chip_info->regmap_config);
if (IS_ERR(regmap)) {
--
2.25.1
Alphabetical sorting and separation of headers for the BMPxxx
SPI driver.
Signed-off-by: Vasileios Amoiridis <[email protected]>
---
drivers/iio/pressure/bmp280-spi.c | 7 ++++---
1 file changed, 4 insertions(+), 3 deletions(-)
diff --git a/drivers/iio/pressure/bmp280-spi.c b/drivers/iio/pressure/bmp280-spi.c
index 1972014dca93..3458806f11fb 100644
--- a/drivers/iio/pressure/bmp280-spi.c
+++ b/drivers/iio/pressure/bmp280-spi.c
@@ -4,11 +4,12 @@
*
* Inspired by the older BMP085 driver drivers/misc/bmp085-spi.c
*/
-#include <linux/module.h>
-#include <linux/spi/spi.h>
+#include <linux/bits.h>
#include <linux/err.h>
+#include <linux/module.h>
#include <linux/regmap.h>
-#include <linux/bits.h>
+
+#include <linux/spi/spi.h>
#include "bmp280.h"
--
2.25.1
On Tue, Feb 20, 2024 at 07:41:25PM +0100, Vasileios Amoiridis wrote:
> Alphabetical sorting and separation of headers for the BMPxxx
> SPI driver.
..
> -#include <linux/module.h>
> -#include <linux/spi/spi.h>
> +#include <linux/bits.h>
> #include <linux/err.h>
> +#include <linux/module.h>
> #include <linux/regmap.h>
> -#include <linux/bits.h>
That's what I meant. Please do not add it into the wrong place to begin with.
> +#include <linux/spi/spi.h>
--
With Best Regards,
Andy Shevchenko
On Tue, Feb 20, 2024 at 07:41:24PM +0100, Vasileios Amoiridis wrote:
> According to the datasheet of BMP38x and BMP390 devices, for an SPI
> read operation the first byte that is returned needs to be dropped,
> and the rest of the bytes are the actual data returned from the
> sensor.
..
> +static int bmp380_regmap_spi_read(void *context, const void *reg,
> + size_t reg_size, void *val, size_t val_size)
> +{
> + struct spi_device *spi = to_spi_device(context);
> + u8 rx_buf[4];
> + ssize_t status;
> +
> + /*
> + * Maximum number of consecutive bytes read for a temperature or
> + * pressure measurement is 3.
> + */
> + if (val_size > 3)
> + return -EINVAL;
I would add a blank line here.
> + /*
> + * According to the BMP3xx datasheets, for a basic SPI read opertion,
> + * the first byte needs to be dropped and the rest are the requested
> + * data.
> + */
> + status = spi_write_then_read(spi, reg, 1, rx_buf, val_size + 1);
> + if (status)
> + return status;
> +
> + memcpy(val, rx_buf + 1, val_size);
> +
> + return 0;
> +}
With above and bits.h location being addressed
Reviewed-by: Andy Shevchenko <[email protected]>
--
With Best Regards,
Andy Shevchenko
On Tue, 20 Feb 2024 21:57:35 +0200
Andy Shevchenko <[email protected]> wrote:
> On Tue, Feb 20, 2024 at 07:41:24PM +0100, Vasileios Amoiridis wrote:
> > According to the datasheet of BMP38x and BMP390 devices, for an SPI
> > read operation the first byte that is returned needs to be dropped,
> > and the rest of the bytes are the actual data returned from the
> > sensor.
>
> ...
>
> > +static int bmp380_regmap_spi_read(void *context, const void *reg,
> > + size_t reg_size, void *val, size_t val_size)
> > +{
> > + struct spi_device *spi = to_spi_device(context);
> > + u8 rx_buf[4];
> > + ssize_t status;
> > +
> > + /*
> > + * Maximum number of consecutive bytes read for a temperature or
> > + * pressure measurement is 3.
> > + */
> > + if (val_size > 3)
> > + return -EINVAL;
>
> I would add a blank line here.
>
> > + /*
> > + * According to the BMP3xx datasheets, for a basic SPI read opertion,
> > + * the first byte needs to be dropped and the rest are the requested
> > + * data.
> > + */
> > + status = spi_write_then_read(spi, reg, 1, rx_buf, val_size + 1);
> > + if (status)
> > + return status;
> > +
> > + memcpy(val, rx_buf + 1, val_size);
> > +
> > + return 0;
> > +}
>
> With above and bits.h location being addressed
> Reviewed-by: Andy Shevchenko <[email protected]>
>
I'd picked up previous version and tweaked it for the header being first.
Now updated the spacing above and added your tag.
Only did this rebase because it was the top of my fixes tree.
On Tue, 20 Feb 2024 21:56:15 +0200
Andy Shevchenko <[email protected]> wrote:
> On Tue, Feb 20, 2024 at 07:41:25PM +0100, Vasileios Amoiridis wrote:
> > Alphabetical sorting and separation of headers for the BMPxxx
> > SPI driver.
>
> ...
>
> > -#include <linux/module.h>
> > -#include <linux/spi/spi.h>
> > +#include <linux/bits.h>
> > #include <linux/err.h>
> > +#include <linux/module.h>
> > #include <linux/regmap.h>
>
> > -#include <linux/bits.h>
>
> That's what I meant. Please do not add it into the wrong place to begin with.
>
> > +#include <linux/spi/spi.h>
>
This isn't going be something I rush in with the fix, so
plenty of time to revisit this next cycle.
Thanks,
Jonathan