2024-02-26 21:28:28

by Sebastian Reichel

[permalink] [raw]
Subject: [PATCH v5 0/6] UNI-T UTi260B support

From: Sebastian Reichel <[email protected]>

Hi,

This adds adds support for the UNI-T UTi260B thermal camera, which is based
on i.MX6ULL. The series first updates DT bindings, so that CHECK_DTBS no
longer reports any errors for i.MX6ULL (i.e. for an empty board). They are
not specific to the UTi260B and in fact that machine has most of the IP
handled by these patches marked as disabled. The last patch adds the actual
thermal camera DT.

The DT is based on reverse engineered information. More information about
the device can be found in this presentation from Embedded Recipes 2023:

* https://embedded-recipes.org/2023/wp-content/uploads/2023/10/Running-FOSS-on-a-Thermal-Camera-Sebastian-Reichel-compressed.pdf
* https://www.youtube.com/watch?v=uvObsCG-Cqo

I also prepared a branch with these patches (and a minimal kernel config)
and published it here:

https://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-misc.git/log/?h=uti260b-v5

Changes since PATCHv4:
* https://lore.kernel.org/all/[email protected]/
- drop merged patches
- use new NXP mailing list
- UTi260B board DT: change patch title
- UTi260B board DT: fix node order

Changes since PATCHv3:
* https://lore.kernel.org/all/[email protected]/
- weim binding: use " instead of '
- weim binding: use "if: not: required: - foo" instead of "if: properties: foo: false"
- imx6ull-uti260b.dts: merge ecspi3_csgrp into ecspi3grp
- collect Reviewed-by from Krzysztof Kozlowski

Changes since PATCHv2:
* https://lore.kernel.org/all/[email protected]/
- drop fsl,imx-asrc YAML binding conversion (merged)
- collect a bunch of Reviewed-by/Acked-by tags
- weim DT binding: fix issue with requirements
- xnur-gpio -> xnur-gpios change: Improve patch long description

Changes since PATCHv1:
* https://lore.kernel.org/all/[email protected]/
- uni-t,imx6ull-uti260b -> uni-t,uti260b
- add Acked-by for uni-t vendor prefix
- add Acked-by for HDMI audio index fix
- add Acked-by for LCDIF power-domain requirement drop
- anatop DT binding: Fixed indentation in example
- anatop DT binding: Described IRQs
- touchscreen DT binding: change tsc@ to touchscreen@ in example
- touchscreen DT binding: change xnur-gpio to xnur-gpios
- weim DT binding: drop acme,whatever example
- weim DT binding: use flash@ instead of nor@
- weim DT binding: update weim.txt reference in arcx,anybus-controller.txt
- weim DT binding: switch to memory-controller binding
- fsl,imx-asrc DT binding: fix ASoC patch subject prefix
- fsl,imx-asrc DT binding: add constraints
- add new patch fixing xnur-gpio(s) in all i.MX6UL board DT files
- add new patch fixing touchscreen nodename in i.MX6UL SoC DT file
- add new patch fixing weim nodename in all i.MX SoC DT files
- device DTS: use color/functions for the led
- device DTS: increase SPI speed
- device DTS: add comment for SD / eMMC node

Unadressed feedback from PATCHv1:
- anatop phandle vs parent: technically it makes sense to just use the
parent, but this driver is only used by i.MX6. The current code makes
use of the phandle, so we cannot drop it because of backwards
compatibility. So I don't see a point in deprecating this property.
- touchscreen binding: I kept measure-delay-time and pre-charge-time
values in hex, since that is being used everywhere and the unit
is unknown. The values are directly written into HW registers and
the i.MX6UL TRM does not provide any hints about the unit. I do not
have an i.MX6UL device with a touchsreen, so I cannot test either.
- regulator name in DT: I did not rename the regulators to just
"regulator", since the nodename must be unique.

Greetings,

-- Sebastian

Sebastian Reichel (6):
dt-bindings: pinctrl: fsl,imx6ul-pinctrl: convert to YAML
dt-bindings: input: touchscreen: fsl,imx6ul-tsc convert to YAML
dt-bindings: soc: imx: fsl,imx-anatop: add binding
dt-bindings: soc: imx: fsl,imx-iomuxc-gpr: add imx6
dt-bindings: fsl-imx-sdma: fix HDMI audio index
ARM: dts: imx: Add UNI-T UTi260B thermal camera board

.../devicetree/bindings/dma/fsl,imx-sdma.yaml | 3 +-
.../input/touchscreen/fsl,imx6ul-tsc.yaml | 97 +++
.../bindings/input/touchscreen/imx6ul_tsc.txt | 38 --
.../bindings/pinctrl/fsl,imx6ul-pinctrl.txt | 37 --
.../bindings/pinctrl/fsl,imx6ul-pinctrl.yaml | 116 ++++
.../bindings/soc/imx/fsl,imx-anatop.yaml | 128 ++++
.../bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml | 18 +-
arch/arm/boot/dts/nxp/imx/Makefile | 1 +
arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts | 566 ++++++++++++++++++
9 files changed, 927 insertions(+), 77 deletions(-)
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/fsl,imx6ul-tsc.yaml
delete mode 100644 Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt
delete mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt
create mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.yaml
create mode 100644 Documentation/devicetree/bindings/soc/imx/fsl,imx-anatop.yaml
create mode 100644 arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts

--
2.43.0



2024-02-26 21:29:16

by Sebastian Reichel

[permalink] [raw]
Subject: [PATCH v5 5/6] dt-bindings: fsl-imx-sdma: fix HDMI audio index

HDMI Audio has been added to the DT binding documentation with an
incorrect index. DT and the driver use index 26. This happened,
because the binding is missing MULTI_SAI type, which is using
index 25.

Reported-by: Michael Yackavage <[email protected]>
Fixes: 7bdbd87d4008 ("dt-bindings: fsl-imx-sdma: Convert imx sdma to DT schema")
Acked-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
---
Documentation/devicetree/bindings/dma/fsl,imx-sdma.yaml | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/dma/fsl,imx-sdma.yaml b/Documentation/devicetree/bindings/dma/fsl,imx-sdma.yaml
index b95dd8db5a30..37135fa024f9 100644
--- a/Documentation/devicetree/bindings/dma/fsl,imx-sdma.yaml
+++ b/Documentation/devicetree/bindings/dma/fsl,imx-sdma.yaml
@@ -92,7 +92,8 @@ properties:
description: needs firmware more than ver 2
- Shared ASRC: 23
- SAI: 24
- - HDMI Audio: 25
+ - Multi SAI: 25
+ - HDMI Audio: 26

The third cell: transfer priority ID
enum:
--
2.43.0


2024-02-26 21:30:47

by Sebastian Reichel

[permalink] [raw]
Subject: [PATCH v5 2/6] dt-bindings: input: touchscreen: fsl,imx6ul-tsc convert to YAML

Convert the i.MX6UL touchscreen DT binding to YAML.

Reviewed-by: Rob Herring <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
---
.../input/touchscreen/fsl,imx6ul-tsc.yaml | 97 +++++++++++++++++++
.../bindings/input/touchscreen/imx6ul_tsc.txt | 38 --------
2 files changed, 97 insertions(+), 38 deletions(-)
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/fsl,imx6ul-tsc.yaml
delete mode 100644 Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt

diff --git a/Documentation/devicetree/bindings/input/touchscreen/fsl,imx6ul-tsc.yaml b/Documentation/devicetree/bindings/input/touchscreen/fsl,imx6ul-tsc.yaml
new file mode 100644
index 000000000000..678756ad0f92
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/fsl,imx6ul-tsc.yaml
@@ -0,0 +1,97 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/touchscreen/fsl,imx6ul-tsc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale i.MX6UL Touch Controller
+
+maintainers:
+ - Haibo Chen <[email protected]>
+ - Shawn Guo <[email protected]>
+ - Sascha Hauer <[email protected]>
+
+properties:
+ compatible:
+ const: fsl,imx6ul-tsc
+
+ reg:
+ items:
+ - description: touch controller address
+ - description: ADC2 address
+
+ interrupts:
+ items:
+ - description: touch controller address
+ - description: ADC2 address
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ items:
+ - const: tsc
+ - const: adc
+
+ xnur-gpios:
+ maxItems: 1
+ description:
+ The X- gpio this controller connect to. This xnur-gpio returns to
+ low once the finger leave the touch screen (The last touch event
+ the touch controller capture).
+
+ measure-delay-time:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ The value of measure delay time. Before X-axis or Y-axis measurement,
+ the screen need some time before even potential distribution ready.
+ default: 0xffff
+ minimum: 0
+ maximum: 0xffffff
+
+ pre-charge-time:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ The touch screen need some time to precharge.
+ default: 0xfff
+ minimum: 0
+ maximum: 0xffffffff
+
+ touchscreen-average-samples:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Number of data samples which are averaged for each read.
+ enum: [ 1, 4, 8, 16, 32 ]
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+ - xnur-gpios
+
+allOf:
+ - $ref: touchscreen.yaml#
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/imx6ul-clock.h>
+ #include <dt-bindings/gpio/gpio.h>
+ touchscreen@2040000 {
+ compatible = "fsl,imx6ul-tsc";
+ reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_IPG>,
+ <&clks IMX6UL_CLK_ADC2>;
+ clock-names = "tsc", "adc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tsc>;
+ xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ measure-delay-time = <0xfff>;
+ pre-charge-time = <0xffff>;
+ touchscreen-average-samples = <32>;
+ };
diff --git a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt
deleted file mode 100644
index 164915004424..000000000000
--- a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt
+++ /dev/null
@@ -1,38 +0,0 @@
-* Freescale i.MX6UL Touch Controller
-
-Required properties:
-- compatible: must be "fsl,imx6ul-tsc".
-- reg: this touch controller address and the ADC2 address.
-- interrupts: the interrupt of this touch controller and ADC2.
-- clocks: the root clock of touch controller and ADC2.
-- clock-names; must be "tsc" and "adc".
-- xnur-gpio: the X- gpio this controller connect to.
- This xnur-gpio returns to low once the finger leave the touch screen (The
- last touch event the touch controller capture).
-
-Optional properties:
-- measure-delay-time: the value of measure delay time.
- Before X-axis or Y-axis measurement, the screen need some time before
- even potential distribution ready.
- This value depends on the touch screen.
-- pre-charge-time: the touch screen need some time to precharge.
- This value depends on the touch screen.
-- touchscreen-average-samples: Number of data samples which are averaged for
- each read. Valid values are 1, 4, 8, 16 and 32.
-
-Example:
- tsc: tsc@2040000 {
- compatible = "fsl,imx6ul-tsc";
- reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_IPG>,
- <&clks IMX6UL_CLK_ADC2>;
- clock-names = "tsc", "adc";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_tsc>;
- xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
- measure-delay-time = <0xfff>;
- pre-charge-time = <0xffff>;
- touchscreen-average-samples = <32>;
- };
--
2.43.0


2024-02-26 21:31:54

by Sebastian Reichel

[permalink] [raw]
Subject: [PATCH v5 6/6] ARM: dts: imx: Add UNI-T UTi260B thermal camera board

Add DT for the UNI-T UTi260B handheld thermal camera.

Reviewed-by: Stefan Wahren <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
---
arch/arm/boot/dts/nxp/imx/Makefile | 1 +
arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts | 566 ++++++++++++++++++
2 files changed, 567 insertions(+)
create mode 100644 arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts

diff --git a/arch/arm/boot/dts/nxp/imx/Makefile b/arch/arm/boot/dts/nxp/imx/Makefile
index a724d1a7a9a0..47350cf3ddeb 100644
--- a/arch/arm/boot/dts/nxp/imx/Makefile
+++ b/arch/arm/boot/dts/nxp/imx/Makefile
@@ -349,6 +349,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ull-tarragon-slavext.dtb \
imx6ull-tqma6ull2-mba6ulx.dtb \
imx6ull-tqma6ull2l-mba6ulx.dtb \
+ imx6ull-uti260b.dtb \
imx6ulz-14x14-evk.dtb \
imx6ulz-bsh-smm-m2.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts
new file mode 100644
index 000000000000..e4576d509a5b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts
@@ -0,0 +1,566 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// Copyright (C) 2022-2024 Sebastian Reichel <[email protected]>
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/clock/imx6ul-clock.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "UNI-T UTi260B Thermal Camera";
+ compatible = "uni-t,uti260b", "fsl,imx6ull";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>;
+ };
+
+ panel_backlight: backlight {
+ compatible = "pwm-backlight";
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ enable-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_backlight_enable>;
+ power-supply = <&reg_vsd>;
+ pwms = <&pwm1 0 50000 0>;
+ };
+
+ battery: battery {
+ compatible = "simple-battery";
+ /* generic 26650 battery */
+ device-chemistry = "lithium-ion";
+ charge-full-design-microamp-hours = <5000000>;
+ voltage-max-design-microvolt = <4200000>;
+ voltage-min-design-microvolt = <3300000>;
+ };
+
+ tp5000: charger {
+ compatible = "gpio-charger";
+ charger-type = "usb-sdp";
+ gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_charger_stat1>;
+ };
+
+ fuel-gauge {
+ compatible = "adc-battery";
+ charged-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+ io-channel-names = "voltage";
+ io-channels = <&adc1 7>;
+ monitored-battery = <&battery>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_charger_stat2>;
+ power-supplies = <&tp5000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_gpio_keys>;
+ autorepeat;
+
+ up-key {
+ label = "Up";
+ gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_UP>;
+ };
+
+ down-key {
+ label = "Down";
+ gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_DOWN>;
+ };
+
+ left-key {
+ label = "Left";
+ gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_LEFT>;
+ };
+
+ right-key {
+ label = "Right";
+ gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RIGHT>;
+ };
+
+ ok-key {
+ label = "Ok";
+ gpios = <&gpio2 9 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_ENTER>;
+ };
+
+ return-key {
+ label = "Return";
+ gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_ESC>;
+ };
+
+ play-key {
+ label = "Media";
+ gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_MEDIA>;
+ };
+
+ trigger-key {
+ label = "Trigger";
+ gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_TRIGGER>;
+ };
+
+ power-key {
+ label = "Power";
+ gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ };
+
+ light-key {
+ label = "Light";
+ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_LIGHTS_TOGGLE>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_led_ctrl>;
+
+ led {
+ color = <LED_COLOR_ID_WHITE>;
+ function = LED_FUNCTION_FLASH;
+ gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_poweroff>;
+ };
+
+ reg_vref: regulator-vref-4v2 {
+ compatible = "regulator-fixed";
+ regulator-name = "VREF_4V2";
+ regulator-min-microvolt = <4200000>;
+ regulator-max-microvolt = <4200000>;
+ };
+
+ reg_vsd: regulator-vsd {
+ compatible = "regulator-fixed";
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&adc1 {
+ #io-channel-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_adc>;
+ vref-supply = <&reg_vref>;
+ status = "okay";
+};
+
+&csi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_csi>;
+ status = "okay";
+
+ port {
+ parallel_from_gc0308: endpoint {
+ remote-endpoint = <&gc0308_to_parallel>;
+ };
+ };
+};
+
+&ecspi3 {
+ cs-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_spi3>;
+ status = "okay";
+
+ panel@0 {
+ compatible = "inanbo,t28cp45tn89-v17";
+ reg = <0>;
+ backlight = <&panel_backlight>;
+ power-supply = <&reg_vsd>;
+ spi-cpha;
+ spi-cpol;
+ spi-max-frequency = <1000000>;
+ spi-rx-bus-width = <0>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+};
+
+&gpio1 {
+ ir-reset-hog {
+ gpio-hog;
+ gpios = <3 GPIO_ACTIVE_LOW>;
+ line-name = "ir-reset-gpio";
+ output-low;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_ir_reset>;
+ };
+};
+
+&gpio2 {
+ /* configuring this to output-high results in poweroff */
+ power-en-hog {
+ gpio-hog;
+ gpios = <6 GPIO_ACTIVE_HIGH>;
+ line-name = "power-en-gpio";
+ output-low;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_poweroff2>;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_i2c1>;
+ status = "okay";
+
+ camera@21 {
+ compatible = "galaxycore,gc0308";
+ reg = <0x21>;
+ clocks = <&clks IMX6UL_CLK_CSI>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_gc0308>;
+ powerdown-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ vdd28-supply = <&reg_vsd>;
+
+ port {
+ gc0308_to_parallel: endpoint {
+ remote-endpoint = <&parallel_from_gc0308>;
+ bus-width = <8>;
+ data-shift = <2>; /* lines 9:2 are used */
+ hsync-active = <1>; /* active high */
+ vsync-active = <1>; /* active high */
+ data-active = <1>; /* active high */
+ pclk-sample = <1>; /* sample on rising edge */
+ };
+ };
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_i2c2>;
+ status = "okay";
+
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&lcdif {
+ assigned-clocks = <&clks IMX6UL_CLK_LCDIF_PRE_SEL>;
+ assigned-clock-parents = <&clks IMX6UL_CLK_PLL5_VIDEO_DIV>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_lcd_data>, <&mux_lcd_ctrl>;
+ status = "okay";
+
+ port {
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_pwm>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_uart>;
+ status = "okay";
+};
+
+&usbotg1 {
+ /* USB-C connector */
+ disable-over-current;
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbotg2 {
+ /* thermal sensor */
+ disable-over-current;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy1 {
+ fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+ fsl,tx-d-cal = <106>;
+};
+
+&usdhc1 {
+ /* MicroSD */
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ keep-power-in-suspend;
+ no-1-8-v;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&mux_sdhc1>, <&mux_sdhc1_cd>;
+ pinctrl-1 = <&mux_sdhc1_100mhz>, <&mux_sdhc1_cd>;
+ pinctrl-2 = <&mux_sdhc1_200mhz>, <&mux_sdhc1_cd>;
+ wakeup-source;
+ vmmc-supply = <&reg_vsd>;
+ status = "okay";
+};
+
+&usdhc2 {
+ /* eMMC */
+ keep-power-in-suspend;
+ no-1-8-v;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_sdhc2>;
+ wakeup-source;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_wdog>;
+};
+
+&iomuxc {
+ mux_adc: adcgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__GPIO1_IO07 0xb0
+ >;
+ };
+
+ mux_backlight_enable: blenablegrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x3008
+ >;
+ };
+
+ mux_charger_stat1: charger1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0x3008
+ >;
+ };
+
+ mux_charger_stat2: charger2grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0x3008
+ >;
+ };
+
+ mux_csi: csi1grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088
+ MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088
+ MX6UL_PAD_CSI_HSYNC__CSI_HSYNC 0x1b088
+ MX6UL_PAD_CSI_DATA00__CSI_DATA02 0x1b088
+ MX6UL_PAD_CSI_DATA01__CSI_DATA03 0x1b088
+ MX6UL_PAD_CSI_DATA02__CSI_DATA04 0x1b088
+ MX6UL_PAD_CSI_DATA03__CSI_DATA05 0x1b088
+ MX6UL_PAD_CSI_DATA04__CSI_DATA06 0x1b088
+ MX6UL_PAD_CSI_DATA05__CSI_DATA07 0x1b088
+ MX6UL_PAD_CSI_DATA06__CSI_DATA08 0x1b088
+ MX6UL_PAD_CSI_DATA07__CSI_DATA09 0x1b088
+ >;
+ };
+
+ mux_gc0308: gc0308grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1e038
+ MX6UL_PAD_GPIO1_IO05__GPIO1_IO05 0x1b088
+ MX6UL_PAD_GPIO1_IO06__GPIO1_IO06 0x1b088
+ >;
+ };
+
+ mux_gpio_keys: gpiokeygrp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11 0x3008
+ MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12 0x3008
+ MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13 0x3008
+ MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10 0x3008
+ MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09 0x3008
+ MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15 0x3008
+ MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08 0x3008
+ MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14 0x3008
+ MX6UL_PAD_ENET1_TX_DATA0__GPIO2_IO03 0x3008
+ MX6UL_PAD_ENET1_RX_DATA1__GPIO2_IO01 0x3008
+ >;
+ };
+
+ mux_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
+ MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
+ >;
+ };
+
+ mux_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001f8a8
+ MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001f8a8
+ >;
+ };
+
+ mux_ir_reset: irresetgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0x3008
+ >;
+ };
+
+ mux_lcd_ctrl: lcdifctrlgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79
+ MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79
+ MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79
+ MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79
+ >;
+ };
+
+ mux_lcd_data: lcdifdatgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79
+ MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79
+ MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79
+ MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79
+ MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79
+ MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79
+ MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79
+ MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79
+ MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79
+ MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79
+ MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79
+ MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79
+ MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79
+ MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79
+ MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79
+ MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79
+ MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79
+ MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79
+ >;
+ };
+
+ mux_led_ctrl: ledctrlgrp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_RX_EN__GPIO2_IO02 0x3008
+ >;
+ };
+
+ mux_poweroff: poweroffgrp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_TX_DATA1__GPIO2_IO04 0x3008
+ >;
+ };
+
+ mux_poweroff2: poweroff2grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_TX_CLK__GPIO2_IO06 0x3008
+ >;
+ };
+
+ mux_pwm: pwm1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO08__PWM1_OUT 0x110b0
+ >;
+ };
+
+ mux_sdhc1: sdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10071
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
+ >;
+ };
+
+ mux_sdhc1_100mhz: sdhc1-100mhz-grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x170b9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
+ >;
+ };
+
+ mux_sdhc1_200mhz: sdhc1-200mhz-grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x170f9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
+ >;
+ };
+
+ mux_sdhc1_cd: sdhc1-cd-grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059
+ >;
+ };
+
+ mux_sdhc2: sdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10069
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17059
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17059
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17059
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17059
+ >;
+ };
+
+ mux_spi3: ecspi3grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI 0x100b1
+ MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK 0x100b1
+ MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20 0x3008
+ >;
+ };
+
+ mux_uart: uartgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ mux_wdog: wdoggrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY 0x30b0
+ >;
+ };
+};
--
2.43.0


2024-03-05 17:31:43

by Dmitry Torokhov

[permalink] [raw]
Subject: Re: [PATCH v5 2/6] dt-bindings: input: touchscreen: fsl,imx6ul-tsc convert to YAML

On Mon, Feb 26, 2024 at 10:26:24PM +0100, Sebastian Reichel wrote:
> Convert the i.MX6UL touchscreen DT binding to YAML.
>
> Reviewed-by: Rob Herring <[email protected]>
> Signed-off-by: Sebastian Reichel <[email protected]>

Should I pick it though my tree or you'll push the whole bunch through
some other tree? If the latter:

Acked-by: Dmitry Torokhov <[email protected]>

Thanks.

--
Dmitry

2024-03-05 17:35:06

by Rob Herring (Arm)

[permalink] [raw]
Subject: Re: [PATCH v5 0/6] UNI-T UTi260B support

On Mon, Feb 26, 2024 at 10:26:22PM +0100, Sebastian Reichel wrote:
> From: Sebastian Reichel <[email protected]>
>
> Hi,
>
> This adds adds support for the UNI-T UTi260B thermal camera, which is based
> on i.MX6ULL. The series first updates DT bindings, so that CHECK_DTBS no
> longer reports any errors for i.MX6ULL (i.e. for an empty board). They are
> not specific to the UTi260B and in fact that machine has most of the IP
> handled by these patches marked as disabled. The last patch adds the actual
> thermal camera DT.

I imagine that this has missed 6.9 for arm-soc, so I've applied the
binding patches. The anatop binding in particular fixes a warning in
dt_binding_check.

Rob

2024-03-28 13:55:23

by Shawn Guo

[permalink] [raw]
Subject: Re: [PATCH v5 6/6] ARM: dts: imx: Add UNI-T UTi260B thermal camera board

On Mon, Feb 26, 2024 at 10:26:28PM +0100, Sebastian Reichel wrote:
> Add DT for the UNI-T UTi260B handheld thermal camera.
>
> Reviewed-by: Stefan Wahren <[email protected]>
> Signed-off-by: Sebastian Reichel <[email protected]>

Applied, thanks!