This series adds device-tree nodes for CPSW2G and CPSW9G instance
of the CPSW Ethernet Switch on TI's J784S4 SoC. Additionally,
two device-tree overlays are also added:
1. QSGMII mode with the CPSW9G instance via the ENET EXPANSION 1
connector.
2. USXGMII mode with MAC Ports 1 and 2 of the CPSW9G instance via
ENET EXPANSION 1 and 2 connectors, configured in fixed-link
mode of operation at 5Gbps link speed.
Link to v4:
https://lore.kernel.org/r/[email protected]/
Changes from v4 to v5:
1. Removed Patch at:
https://lore.kernel.org/r/[email protected]/
from this version as it is posted as a separate patch at:
https://lore.kernel.org/r/[email protected]/
2. Disabled node "main_cpsw1_mdio" in k3-j784s4-main.dtsi and enabled it
in k3-j784s4-evm.dts.
Chintan Vankar (1):
arm64: dts: ti: k3-j784s4-evm: Add alias for MCU CPSW2G
Siddharth Vadapalli (4):
arm64: dts: ti: k3-j784s4-main: Add CPSW2G and CPSW9G nodes
arm64: dts: ti: k3-j784s4-evm: Enable Main CPSW2G node and add aliases
for it
arm64: dts: ti: k3-j784s4: Add overlay to enable QSGMII mode with
CPSW9G
arm64: dts: ti: k3-j784s4: Add overlay for dual port USXGMII mode
arch/arm64/boot/dts/ti/Makefile | 11 +-
.../ti/k3-j784s4-evm-quad-port-eth-exp1.dtso | 147 ++++++++++++++
.../ti/k3-j784s4-evm-usxgmii-exp1-exp2.dtso | 81 ++++++++
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 51 +++++
arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 187 ++++++++++++++++++
5 files changed, 476 insertions(+), 1 deletion(-)
create mode 100644 arch/arm64/boot/dts/ti/k3-j784s4-evm-quad-port-eth-exp1.dtso
create mode 100644 arch/arm64/boot/dts/ti/k3-j784s4-evm-usxgmii-exp1-exp2.dtso
--
2.34.1
Add alias for the MCU CPSW2G port to enable Linux to fetch MAC Address
for the port directly from U-Boot.
Signed-off-by: Chintan Vankar <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index 81fd7afac8c5..1f390c22844e 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -27,6 +27,7 @@ aliases {
mmc1 = &main_sdhci1;
i2c0 = &wkup_i2c0;
i2c3 = &main_i2c0;
+ ethernet0 = &mcu_cpsw_port1;
};
memory@80000000 {
--
2.34.1
From: Siddharth Vadapalli <[email protected]>
J784S4 SoC has MAIN CPSW2G and CPSW9G instances of the CPSW
Ethernet Switch. CPSW2G has 1 external port and 1 host port
while CPSW9G has 8 external ports and 1 host port.
Add device-tree nodes for MAIN CPSW2G and CPSW9G and disable
them by default. MAIN CPSW2G will be enabled in the board file
while device-tree overlays will be used to enable CPSW9G.
Signed-off-by: Siddharth Vadapalli <[email protected]>
Signed-off-by: Chintan Vankar <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 187 +++++++++++++++++++++
1 file changed, 187 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
index b67c37460a73..ddf28b2143aa 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
@@ -48,6 +48,19 @@ scm_conf: bus@100000 {
#size-cells = <1>;
ranges = <0x00 0x00 0x00100000 0x1c000>;
+ cpsw1_phy_gmii_sel: phy@4034 {
+ compatible = "ti,am654-phy-gmii-sel";
+ reg = <0x4034 0x4>;
+ #phy-cells = <1>;
+ };
+
+ cpsw0_phy_gmii_sel: phy@4044 {
+ compatible = "ti,j784s4-cpsw9g-phy-gmii-sel";
+ ti,qsgmii-main-ports = <7>, <7>;
+ reg = <0x4044 0x20>;
+ #phy-cells = <1>;
+ };
+
serdes_ln_ctrl: mux-controller@4080 {
compatible = "reg-mux";
reg = <0x00004080 0x30>;
@@ -1439,6 +1452,180 @@ cpts@310d0000 {
};
};
+ main_cpsw0: ethernet@c000000 {
+ compatible = "ti,j784s4-cpswxg-nuss";
+ reg = <0x00 0xc000000 0x00 0x200000>;
+ reg-names = "cpsw_nuss";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x00 0x00 0x00 0xc000000 0x00 0x200000>;
+ dma-coherent;
+ clocks = <&k3_clks 64 0>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 64 TI_SCI_PD_EXCLUSIVE>;
+
+ dmas = <&main_udmap 0xca00>,
+ <&main_udmap 0xca01>,
+ <&main_udmap 0xca02>,
+ <&main_udmap 0xca03>,
+ <&main_udmap 0xca04>,
+ <&main_udmap 0xca05>,
+ <&main_udmap 0xca06>,
+ <&main_udmap 0xca07>,
+ <&main_udmap 0x4a00>;
+ dma-names = "tx0", "tx1", "tx2", "tx3",
+ "tx4", "tx5", "tx6", "tx7",
+ "rx";
+
+ status = "disabled";
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ main_cpsw0_port1: port@1 {
+ reg = <1>;
+ label = "port1";
+ ti,mac-only;
+ status = "disabled";
+ };
+
+ main_cpsw0_port2: port@2 {
+ reg = <2>;
+ label = "port2";
+ ti,mac-only;
+ status = "disabled";
+ };
+
+ main_cpsw0_port3: port@3 {
+ reg = <3>;
+ label = "port3";
+ ti,mac-only;
+ status = "disabled";
+ };
+
+ main_cpsw0_port4: port@4 {
+ reg = <4>;
+ label = "port4";
+ ti,mac-only;
+ status = "disabled";
+ };
+
+ main_cpsw0_port5: port@5 {
+ reg = <5>;
+ label = "port5";
+ ti,mac-only;
+ status = "disabled";
+ };
+
+ main_cpsw0_port6: port@6 {
+ reg = <6>;
+ label = "port6";
+ ti,mac-only;
+ status = "disabled";
+ };
+
+ main_cpsw0_port7: port@7 {
+ reg = <7>;
+ label = "port7";
+ ti,mac-only;
+ status = "disabled";
+ };
+
+ main_cpsw0_port8: port@8 {
+ reg = <8>;
+ label = "port8";
+ ti,mac-only;
+ status = "disabled";
+ };
+ };
+
+ main_cpsw0_mdio: mdio@f00 {
+ compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+ reg = <0x00 0xf00 0x00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&k3_clks 64 0>;
+ clock-names = "fck";
+ bus_freq = <1000000>;
+ status = "disabled";
+ };
+
+ cpts@3d000 {
+ compatible = "ti,am65-cpts";
+ reg = <0x00 0x3d000 0x00 0x400>;
+ clocks = <&k3_clks 64 3>;
+ clock-names = "cpts";
+ interrupts-extended = <&gic500 GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "cpts";
+ ti,cpts-ext-ts-inputs = <4>;
+ ti,cpts-periodic-outputs = <2>;
+ };
+ };
+
+ main_cpsw1: ethernet@c200000 {
+ compatible = "ti,j721e-cpsw-nuss";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ reg = <0x00 0xc200000 0x00 0x200000>;
+ reg-names = "cpsw_nuss";
+ ranges = <0x00 0x00 0x00 0xc200000 0x00 0x200000>;
+ dma-coherent;
+ clocks = <&k3_clks 62 0>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 62 TI_SCI_PD_EXCLUSIVE>;
+
+ dmas = <&main_udmap 0xc640>,
+ <&main_udmap 0xc641>,
+ <&main_udmap 0xc642>,
+ <&main_udmap 0xc643>,
+ <&main_udmap 0xc644>,
+ <&main_udmap 0xc645>,
+ <&main_udmap 0xc646>,
+ <&main_udmap 0xc647>,
+ <&main_udmap 0x4640>;
+ dma-names = "tx0", "tx1", "tx2", "tx3",
+ "tx4", "tx5", "tx6", "tx7",
+ "rx";
+
+ status = "disabled";
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ main_cpsw1_port1: port@1 {
+ reg = <1>;
+ label = "port1";
+ phys = <&cpsw1_phy_gmii_sel 1>;
+ ti,mac-only;
+ status = "disabled";
+ };
+ };
+
+ main_cpsw1_mdio: mdio@f00 {
+ compatible = "ti,cpsw-mdio", "ti,davinci_mdio";
+ reg = <0x00 0xf00 0x00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&k3_clks 62 0>;
+ clock-names = "fck";
+ bus_freq = <1000000>;
+ status = "disabled";
+ };
+
+ cpts@3d000 {
+ compatible = "ti,am65-cpts";
+ reg = <0x00 0x3d000 0x00 0x400>;
+ clocks = <&k3_clks 62 3>;
+ clock-names = "cpts";
+ interrupts-extended = <&gic500 GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "cpts";
+ ti,cpts-ext-ts-inputs = <4>;
+ ti,cpts-periodic-outputs = <2>;
+ };
+ };
+
main_mcan0: can@2701000 {
compatible = "bosch,m_can";
reg = <0x00 0x02701000 0x00 0x200>,
--
2.34.1
From: Siddharth Vadapalli <[email protected]>
The J7 Quad Port Add-On Ethernet Card for J784S4 EVM supports
QSGMII mode. Use the overlay to configure CPSW9G ports in QSGMII
mode with the Add-On Ethernet Card connected to the ENET Expansion
1 slot on the EVM.
Add support to reset the PHY from kernel by using gpio-hog and
gpio-reset.
Add aliases for CPSW9G ports to enable kernel to fetch MAC Addresses
directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <[email protected]>
Signed-off-by: Chintan Vankar <[email protected]>
---
arch/arm64/boot/dts/ti/Makefile | 7 +-
.../ti/k3-j784s4-evm-quad-port-eth-exp1.dtso | 147 ++++++++++++++++++
2 files changed, 153 insertions(+), 1 deletion(-)
create mode 100644 arch/arm64/boot/dts/ti/k3-j784s4-evm-quad-port-eth-exp1.dtso
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 9a722c2473fb..f8e47278df43 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -100,6 +100,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm.dtb
# Boards with J784s4 SoC
dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm-quad-port-eth-exp1.dtbo
# Build time test only, enabled by CONFIG_OF_ALL_DTBS
k3-am625-beagleplay-csi2-ov5640-dtbs := k3-am625-beagleplay.dtb \
@@ -145,6 +146,8 @@ k3-j721e-sk-csi2-dual-imx219-dtbs := k3-j721e-sk.dtb \
k3-j721e-sk-csi2-dual-imx219.dtbo
k3-j721s2-evm-pcie1-ep-dtbs := k3-j721s2-common-proc-board.dtb \
k3-j721s2-evm-pcie1-ep.dtbo
+k3-j784s4-evm-quad-port-eth-exp1-dtbs := k3-j784s4-evm.dtb \
+ k3-j784s4-evm-quad-port-eth-exp1.dtbo
dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
k3-am625-beagleplay-csi2-tevi-ov5640.dtb \
k3-am625-sk-csi2-imx219.dtb \
@@ -165,7 +168,8 @@ dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
k3-am69-sk-csi2-dual-imx219-dtbs \
k3-j721e-evm-pcie0-ep.dtb \
k3-j721e-sk-csi2-dual-imx219-dtbs \
- k3-j721s2-evm-pcie1-ep.dtb
+ k3-j721s2-evm-pcie1-ep.dtb \
+ k3-j784s4-evm-quad-port-eth-exp1.dtb
# Enable support for device-tree overlays
DTC_FLAGS_k3-am625-beagleplay += -@
@@ -181,3 +185,4 @@ DTC_FLAGS_k3-am69-sk += -@
DTC_FLAGS_k3-j721e-common-proc-board += -@
DTC_FLAGS_k3-j721e-sk += -@
DTC_FLAGS_k3-j721s2-common-proc-board += -@
+DTC_FLAGS_k3-j784s4-evm += -@
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm-quad-port-eth-exp1.dtso b/arch/arm64/boot/dts/ti/k3-j784s4-evm-quad-port-eth-exp1.dtso
new file mode 100644
index 000000000000..0667389b07be
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm-quad-port-eth-exp1.dtso
@@ -0,0 +1,147 @@
+/* SPDX-License-Identifier: GPL-2.0-only OR MIT */
+/**
+ * DT Overlay for CPSW9G in QSGMII mode using J7 Quad Port ETH EXP Add-On Ethernet Card with
+ * J784S4 EVM. The Add-On Ethernet Card has to be connected to ENET Expansion 1 slot on the
+ * board.
+ *
+ * Product Datasheet: https://www.ti.com/lit/ug/spruj74/spruj74.pdf
+ *
+ * Link to QSGMII Daughtercard: https://www.ti.com/tool/J721EXENETXPANEVM
+ *
+ * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy-cadence.h>
+#include <dt-bindings/phy/phy.h>
+
+#include "k3-pinctrl.h"
+#include "k3-serdes.h"
+
+&{/} {
+ aliases {
+ ethernet1 = "/bus@100000/ethernet@c000000/ethernet-ports/port@5";
+ ethernet2 = "/bus@100000/ethernet@c000000/ethernet-ports/port@6";
+ ethernet3 = "/bus@100000/ethernet@c000000/ethernet-ports/port@7";
+ ethernet4 = "/bus@100000/ethernet@c000000/ethernet-ports/port@8";
+ ethernet5 = "/bus@100000/ethernet@c200000/ethernet-ports/port@1";
+ };
+};
+
+&main_cpsw0 {
+ status = "okay";
+};
+
+&main_cpsw0_port5 {
+ status = "okay";
+ phy-handle = <&cpsw9g_phy1>;
+ phy-mode = "qsgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 5>, <&serdes2_qsgmii_link>;
+ phy-names = "mac", "serdes";
+};
+
+&main_cpsw0_port6 {
+ status = "okay";
+ phy-handle = <&cpsw9g_phy2>;
+ phy-mode = "qsgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 6>, <&serdes2_qsgmii_link>;
+ phy-names = "mac", "serdes";
+};
+
+&main_cpsw0_port7 {
+ status = "okay";
+ phy-handle = <&cpsw9g_phy0>;
+ phy-mode = "qsgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 7>, <&serdes2_qsgmii_link>;
+ phy-names = "mac", "serdes";
+};
+
+&main_cpsw0_port8 {
+ status = "okay";
+ phy-handle = <&cpsw9g_phy3>;
+ phy-mode = "qsgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 8>, <&serdes2_qsgmii_link>;
+ phy-names = "mac", "serdes";
+};
+
+&main_cpsw0_mdio {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio0_default_pins>;
+ bus_freq = <1000000>;
+ reset-gpios = <&exp2 17 GPIO_ACTIVE_LOW>;
+ reset-post-delay-us = <120000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpsw9g_phy0: ethernet-phy@16 {
+ reg = <16>;
+ };
+ cpsw9g_phy1: ethernet-phy@17 {
+ reg = <17>;
+ };
+ cpsw9g_phy2: ethernet-phy@18 {
+ reg = <18>;
+ };
+ cpsw9g_phy3: ethernet-phy@19 {
+ reg = <19>;
+ };
+};
+
+&exp2 {
+ /* Power-up ENET1 EXPANDER PHY. */
+ qsgmii-line-hog {
+ gpio-hog;
+ gpios = <16 GPIO_ACTIVE_HIGH>;
+ output-low;
+ };
+
+ /* Toggle MUX2 for MDIO lines */
+ mux-sel-hog {
+ gpio-hog;
+ gpios = <13 GPIO_ACTIVE_HIGH>, <14 GPIO_ACTIVE_HIGH>, <15 GPIO_ACTIVE_HIGH>;
+ output-high;
+ };
+};
+
+&main_pmx0 {
+ mdio0_default_pins: mdio0-default-pins {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x05c, PIN_INPUT, 4) /* (AC36) MCASP2_AXR0.MDIO1_MDIO */
+ J784S4_IOPAD(0x058, PIN_INPUT, 4) /* (AE37) MCASP2_AFSX.MDIO1_MDC */
+ >;
+ };
+};
+
+&serdes_ln_ctrl {
+ idle-states = <J784S4_SERDES0_LANE0_PCIE1_LANE0>, <J784S4_SERDES0_LANE1_PCIE1_LANE1>,
+ <J784S4_SERDES0_LANE2_IP3_UNUSED>, <J784S4_SERDES0_LANE3_USB>,
+ <J784S4_SERDES1_LANE0_PCIE0_LANE0>, <J784S4_SERDES1_LANE1_PCIE0_LANE1>,
+ <J784S4_SERDES1_LANE2_PCIE0_LANE2>, <J784S4_SERDES1_LANE3_PCIE0_LANE3>,
+ <J784S4_SERDES2_LANE0_QSGMII_LANE5>, <J784S4_SERDES2_LANE1_QSGMII_LANE6>,
+ <J784S4_SERDES2_LANE2_QSGMII_LANE7>, <J784S4_SERDES2_LANE3_QSGMII_LANE8>;
+};
+
+&serdes_wiz2 {
+ status = "okay";
+};
+
+&serdes2 {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ serdes2_qsgmii_link: phy@0 {
+ reg = <2>;
+ cdns,num-lanes = <1>;
+ #phy-cells = <0>;
+ cdns,phy-type = <PHY_TYPE_QSGMII>;
+ resets = <&serdes_wiz2 3>;
+ };
+};
--
2.34.1
From: Siddharth Vadapalli <[email protected]>
Enable MAIN CPSW2G and add alias for it to enable Linux to fetch
MAC Address for the port directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <[email protected]>
Signed-off-by: Jayesh Choudhary <[email protected]>
Signed-off-by: Chintan Vankar <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 50 ++++++++++++++++++++++++
1 file changed, 50 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index 1f390c22844e..49195349a156 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -28,6 +28,7 @@ aliases {
i2c0 = &wkup_i2c0;
i2c3 = &main_i2c0;
ethernet0 = &mcu_cpsw_port1;
+ ethernet1 = &main_cpsw1_port1;
};
memory@80000000 {
@@ -281,6 +282,30 @@ &wkup_gpio0 {
&main_pmx0 {
bootph-all;
+ main_cpsw2g_default_pins: main-cpsw2g-default-pins {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x0b8, PIN_INPUT, 6) /* (AC34) MCASP1_ACLKX.RGMII1_RD0 */
+ J784S4_IOPAD(0x0a0, PIN_INPUT, 6) /* (AD34) MCASP0_AXR12.RGMII1_RD1 */
+ J784S4_IOPAD(0x0a4, PIN_INPUT, 6) /* (AJ36) MCASP0_AXR13.RGMII1_RD2 */
+ J784S4_IOPAD(0x0a8, PIN_INPUT, 6) /* (AF34) MCASP0_AXR14.RGMII1_RD3 */
+ J784S4_IOPAD(0x0b0, PIN_INPUT, 6) /* (AL33) MCASP1_AXR3.RGMII1_RXC */
+ J784S4_IOPAD(0x0ac, PIN_INPUT, 6) /* (AE34) MCASP0_AXR15.RGMII1_RX_CTL */
+ J784S4_IOPAD(0x08c, PIN_INPUT, 6) /* (AE35) MCASP0_AXR7.RGMII1_TD0 */
+ J784S4_IOPAD(0x090, PIN_INPUT, 6) /* (AC35) MCASP0_AXR8.RGMII1_TD1 */
+ J784S4_IOPAD(0x094, PIN_INPUT, 6) /* (AG35) MCASP0_AXR9.RGMII1_TD2 */
+ J784S4_IOPAD(0x098, PIN_INPUT, 6) /* (AH36) MCASP0_AXR10.RGMII1_TD3 */
+ J784S4_IOPAD(0x0b4, PIN_INPUT, 6) /* (AL34) MCASP1_AXR4.RGMII1_TXC */
+ J784S4_IOPAD(0x09c, PIN_INPUT, 6) /* (AF35) MCASP0_AXR11.RGMII1_TX_CTL */
+ >;
+ };
+
+ main_cpsw2g_mdio_default_pins: main-cpsw2g-mdio-default-pins {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x0c0, PIN_INPUT, 6) /* (AD38) MCASP1_AXR0.MDIO0_MDC */
+ J784S4_IOPAD(0x0bc, PIN_INPUT, 6) /* (AD33) MCASP1_AFSX.MDIO0_MDIO */
+ >;
+ };
+
main_uart8_pins_default: main-uart8-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -833,6 +858,31 @@ &mcu_cpsw_port1 {
phy-handle = <&mcu_phy0>;
};
+&main_cpsw1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_cpsw2g_default_pins>;
+};
+
+&main_cpsw1_mdio {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_cpsw2g_mdio_default_pins>;
+
+ main_cpsw1_phy0: ethernet-phy@0 {
+ reg = <0>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ };
+};
+
+&main_cpsw1_port1 {
+ status = "okay";
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&main_cpsw1_phy0>;
+};
+
&mailbox0_cluster0 {
status = "okay";
interrupts = <436>;
--
2.34.1
From: Siddharth Vadapalli <[email protected]>
The CPSW9G instance of the CPSW Ethernet Switch supports USXGMII mode
with MAC Ports 1 and 2 of the instance, which are connected to ENET
Expansion 1 and ENET Expansion 2 slots on the EVM respectively, through
the Serdes2 instance of the SERDES.
Enable CPSW9G MAC Ports 1 and 2 in fixed-link configuration USXGMII mode
at 5 Gbps each.
Signed-off-by: Siddharth Vadapalli <[email protected]>
Signed-off-by: Chintan Vankar <[email protected]>
---
arch/arm64/boot/dts/ti/Makefile | 6 +-
.../ti/k3-j784s4-evm-usxgmii-exp1-exp2.dtso | 81 +++++++++++++++++++
2 files changed, 86 insertions(+), 1 deletion(-)
create mode 100644 arch/arm64/boot/dts/ti/k3-j784s4-evm-usxgmii-exp1-exp2.dtso
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index f8e47278df43..2d798ef415e4 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -101,6 +101,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm-quad-port-eth-exp1.dtbo
+dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm-usxgmii-exp1-exp2.dtbo
# Build time test only, enabled by CONFIG_OF_ALL_DTBS
k3-am625-beagleplay-csi2-ov5640-dtbs := k3-am625-beagleplay.dtb \
@@ -148,6 +149,8 @@ k3-j721s2-evm-pcie1-ep-dtbs := k3-j721s2-common-proc-board.dtb \
k3-j721s2-evm-pcie1-ep.dtbo
k3-j784s4-evm-quad-port-eth-exp1-dtbs := k3-j784s4-evm.dtb \
k3-j784s4-evm-quad-port-eth-exp1.dtbo
+k3-j784s4-evm-usxgmii-exp1-exp2.dtbs := k3-j784s4-evm.dtb \
+ k3-j784s4-evm-usxgmii-exp1-exp2.dtbo
dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
k3-am625-beagleplay-csi2-tevi-ov5640.dtb \
k3-am625-sk-csi2-imx219.dtb \
@@ -169,7 +172,8 @@ dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
k3-j721e-evm-pcie0-ep.dtb \
k3-j721e-sk-csi2-dual-imx219-dtbs \
k3-j721s2-evm-pcie1-ep.dtb \
- k3-j784s4-evm-quad-port-eth-exp1.dtb
+ k3-j784s4-evm-quad-port-eth-exp1.dtb \
+ k3-j784s4-evm-usxgmii-exp1-exp2.dtb
# Enable support for device-tree overlays
DTC_FLAGS_k3-am625-beagleplay += -@
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm-usxgmii-exp1-exp2.dtso b/arch/arm64/boot/dts/ti/k3-j784s4-evm-usxgmii-exp1-exp2.dtso
new file mode 100644
index 000000000000..b8e7fed6105a
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm-usxgmii-exp1-exp2.dtso
@@ -0,0 +1,81 @@
+/* SPDX-License-Identifier: GPL-2.0-only OR MIT */
+/**
+ * DT Overlay for CPSW9G in dual port fixed-link USXGMII mode using ENET-1
+ * and ENET-2 Expansion slots of J784S4 EVM.
+ *
+ * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy-cadence.h>
+#include <dt-bindings/phy/phy.h>
+
+#include "k3-serdes.h"
+
+&{/} {
+ aliases {
+ ethernet1 = "/bus@100000/ethernet@c000000/ethernet-ports/port@1";
+ ethernet2 = "/bus@100000/ethernet@c000000/ethernet-ports/port@2";
+ ethernet3 = "/bus@100000/ethernet@c200000/ethernet-ports/port@1";
+ };
+};
+
+&main_cpsw0 {
+ status = "okay";
+ pinctrl-names = "default";
+};
+
+&main_cpsw0_port1 {
+ status = "okay";
+ phy-mode = "usxgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 1>, <&serdes2_usxgmii_link>;
+ phy-names = "mac", "serdes";
+ fixed-link {
+ speed = <5000>;
+ full-duplex;
+ };
+};
+
+&main_cpsw0_port2 {
+ status = "okay";
+ phy-mode = "usxgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 2>, <&serdes2_usxgmii_link>;
+ phy-names = "mac", "serdes";
+ fixed-link {
+ speed = <5000>;
+ full-duplex;
+ };
+};
+
+&serdes_wiz2 {
+ status = "okay";
+ assigned-clock-parents = <&k3_clks 406 9>; /* Use 156.25 MHz clock for USXGMII */
+};
+
+&serdes2 {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ serdes2_usxgmii_link: phy@2 {
+ reg = <2>;
+ cdns,num-lanes = <2>;
+ #phy-cells = <0>;
+ cdns,phy-type = <PHY_TYPE_USXGMII>;
+ resets = <&serdes_wiz2 3>, <&serdes_wiz2 4>;
+ };
+};
+
+&serdes_ln_ctrl {
+ idle-states = <J784S4_SERDES0_LANE0_PCIE1_LANE0>, <J784S4_SERDES0_LANE1_PCIE1_LANE1>,
+ <J784S4_SERDES0_LANE2_IP3_UNUSED>, <J784S4_SERDES0_LANE3_USB>,
+ <J784S4_SERDES1_LANE0_PCIE0_LANE0>, <J784S4_SERDES1_LANE1_PCIE0_LANE1>,
+ <J784S4_SERDES1_LANE2_PCIE0_LANE2>, <J784S4_SERDES1_LANE3_PCIE0_LANE3>,
+ <J784S4_SERDES2_LANE0_IP2_UNUSED>, <J784S4_SERDES2_LANE1_IP2_UNUSED>,
+ <J784S4_SERDES2_LANE2_QSGMII_LANE1>, <J784S4_SERDES2_LANE3_QSGMII_LANE2>;
+};
--
2.34.1
On 12:51-20240314, Chintan Vankar wrote:
> +&serdes2 {
> + status = "okay";
> + #address-cells = <1>;
> + #size-cells = <0>;
Here and elsewhere
Please follow https://docs.kernel.org/devicetree/bindings/dts-coding-style.html#order-of-properties-in-device-node
> + serdes2_qsgmii_link: phy@0 {
> + reg = <2>;
> + cdns,num-lanes = <1>;
> + #phy-cells = <0>;
> + cdns,phy-type = <PHY_TYPE_QSGMII>;
> + resets = <&serdes_wiz2 3>;
> + };
> +};
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D