This series aims to add support for Rockchip RK816 PMIC series. As per
datasheet it's targeted for RK3126/RK3128 (RK816-1), RK1108 (RK816-2) and
PX3-SE (RK816-3) but might be used for other SoCs as well. The MFD consists
of an integrated RTC, a GPIO controller, two 32k clock outputs, a power
key, 3 buck- and 6 ldo regulators, 3 regulator-switches, and charger with
integrated fuel gauge. Charger and fuel gauge are not part of this series.
Two of the switches (otg/boost) are part of the binding, but not of
the driver. They must only ever be enabled if no battery charging is
happening, but it will be enabled automatically if a battery is attached
and an external power source is connected. Thus that needs some
incorporation of a yet to be added charger driver.
Integration in the existing rk8xx-infrastructure was pretty straightforward
and only needed very little tweaking. In order to not further bloat the
driver(s) too much with additional `#define`s I tried to re-use existing
ones wherever possible.
The patches are loosely based on the vendor's implementation, verified
against the datasheet and tested/measured on a RK3126 board. As they are
touching several subsystems I'm sending them (very) early for the
6.10.-cycle.
changes since v1:
- integrated Krzysztof's feedback for the bindings and the resulting
driver changes
- fixed a sparse warning
link to v1:
https://lore.kernel.org/lkml/[email protected]/
changes since v2:
- integrated Krzysztof's feedback to v2 of the bindings and the resulting
driver changes
link to v2:
https://lore.kernel.org/lkml/[email protected]/
Please see individual patches for details about the changes.
Alex Bee (5):
dt-bindings: mfd: Add rk816 binding
mfd: rk8xx: Add RK816 support
pinctrl: rk805: Add rk816 pinctrl support
regulator: rk808: Support apply_bit for
rk808_set_suspend_voltage_range
regulator: rk808: Add RK816 support
.../bindings/mfd/rockchip,rk816.yaml | 274 ++++++++++++++++++
drivers/mfd/Kconfig | 4 +-
drivers/mfd/rk8xx-core.c | 103 +++++++
drivers/mfd/rk8xx-i2c.c | 45 ++-
drivers/pinctrl/pinctrl-rk805.c | 69 +++++
drivers/regulator/rk808-regulator.c | 218 +++++++++++++-
include/linux/mfd/rk808.h | 141 +++++++++
7 files changed, 847 insertions(+), 7 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml
--
2.43.2
Add DT binding document for Rockchip's RK816 PMIC
Signed-off-by: Alex Bee <[email protected]>
---
changes since v1:
- lowercase/hyphens for regulator node names
- rename "-reg" to "-regulator" to make node names generic
- dropped superfluous description for clock-output-names and
wakeup-source
- dropped "|" for text blocks that don't require to preserve formatting
- use full path for `$ref`s
- added pins description to the binding
- added charger function to description
changes since v2:
- dropped "-regulator"-suffix from regulator device names
- use "'"-quotes consistently in the binding
- dropped "pin_fun"-prefix from pin-function names
- added pin to example
.../bindings/mfd/rockchip,rk816.yaml | 274 ++++++++++++++++++
1 file changed, 274 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml
diff --git a/Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml b/Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml
new file mode 100644
index 000000000000..b960ded35e99
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml
@@ -0,0 +1,274 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/rockchip,rk816.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: RK816 Power Management Integrated Circuit
+
+maintainers:
+ - Chris Zhong <[email protected]>
+ - Zhang Qing <[email protected]>
+
+description:
+ Rockchip RK816 series PMIC. This device consists of an i2c controlled MFD
+ that includes regulators, a RTC, a GPIO controller, a power button, and a
+ battery charger manager with fuel gauge.
+
+properties:
+ compatible:
+ enum:
+ - rockchip,rk816
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ '#clock-cells':
+ description:
+ See <dt-bindings/clock/rockchip,rk808.h> for clock IDs.
+ const: 1
+
+ clock-output-names:
+ maxItems: 2
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 2
+
+ system-power-controller:
+ type: boolean
+ description:
+ Telling whether or not this PMIC is controlling the system power.
+
+ wakeup-source:
+ type: boolean
+
+ vcc1-supply:
+ description:
+ The input supply for dcdc1.
+
+ vcc2-supply:
+ description:
+ The input supply for dcdc2.
+
+ vcc3-supply:
+ description:
+ The input supply for dcdc3.
+
+ vcc4-supply:
+ description:
+ The input supply for dcdc4.
+
+ vcc5-supply:
+ description:
+ The input supply for ldo1, ldo2, and ldo3.
+
+ vcc6-supply:
+ description:
+ The input supply for ldo4, ldo5, and ldo6.
+
+ vcc7-supply:
+ description:
+ The input supply for boost.
+
+ vcc8-supply:
+ description:
+ The input supply for otg-switch.
+
+ regulators:
+ type: object
+ patternProperties:
+ '^(boost|dcdc[1-4]|ldo[1-6]|otg-switch)$':
+ type: object
+ $ref: /schemas/regulator/regulator.yaml#
+ unevaluatedProperties: false
+ unevaluatedProperties: false
+
+patternProperties:
+ '-pins$':
+ type: object
+ additionalProperties: false
+ $ref: /schemas/pinctrl/pinmux-node.yaml
+
+ properties:
+ function:
+ enum: [gpio, thermistor]
+
+ pins:
+ $ref: /schemas/types.yaml#/definitions/string
+ const: gpio0
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - '#clock-cells'
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/pinctrl/rockchip.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/gpio/gpio.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rk816: pmic@1a {
+ compatible = "rockchip,rk816";
+ reg = <0x1a>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
+ clock-output-names = "xin32k", "rk816-clkout2";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ gpio-controller;
+ system-power-controller;
+ wakeup-source;
+ #clock-cells = <1>;
+ #gpio-cells = <2>;
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc5-supply = <&vcc33_io>;
+ vcc6-supply = <&vcc_sys>;
+
+ regulators {
+ vdd_cpu: dcdc1 {
+ regulator-name = "vdd_cpu";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <1>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_logic: dcdc2 {
+ regulator-name = "vdd_logic";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <1>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_ddr: dcdc3 {
+ regulator-name = "vcc_ddr";
+ regulator-initial-mode = <1>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc33_io: dcdc4 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc33_io";
+ regulator-initial-mode = <1>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vccio_pmu: ldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_tp: ldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_tp";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_10: ldo3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "vdd_10";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc18_lcd: ldo4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc18_lcd";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vccio_sd: ldo5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vdd10_lcd: ldo6 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "vdd10_lcd";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+ };
+
+ rk816_gpio_pins: gpio-pins {
+ function = "gpio";
+ pins = "gpio0";
+ };
+ };
+ };
--
2.43.2
This integrates RK816 support in the this existing rk8xx mfd driver.
This version has unaligned interrupt registers, which requires to define a
separate get_irq_reg callback for the regmap. Apart from that the
integration is straightforward and the existing structures can be used as
is. The initialization sequence has been taken from vendor kernel.
Signed-off-by: Alex Bee <[email protected]>
---
chnages since v1:
- un-constify rk816_get_irq_reg's return type
drivers/mfd/Kconfig | 4 +-
drivers/mfd/rk8xx-core.c | 103 ++++++++++++++++++++++++++++
drivers/mfd/rk8xx-i2c.c | 45 +++++++++++-
include/linux/mfd/rk808.h | 141 ++++++++++++++++++++++++++++++++++++++
4 files changed, 290 insertions(+), 3 deletions(-)
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 4b023ee229cf..2e7286cc98e4 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1225,7 +1225,7 @@ config MFD_RK8XX
select MFD_CORE
config MFD_RK8XX_I2C
- tristate "Rockchip RK805/RK808/RK809/RK817/RK818 Power Management Chip"
+ tristate "Rockchip RK805/RK808/RK809/RK816/RK817/RK818 Power Management Chip"
depends on I2C && OF
select MFD_CORE
select REGMAP_I2C
@@ -1233,7 +1233,7 @@ config MFD_RK8XX_I2C
select MFD_RK8XX
help
If you say yes here you get support for the RK805, RK808, RK809,
- RK817 and RK818 Power Management chips.
+ RK816, RK817 and RK818 Power Management chips.
This driver provides common support for accessing the device
through I2C interface. The device supports multiple sub-devices
including interrupts, RTC, LDO & DCDC regulators, and onkey.
diff --git a/drivers/mfd/rk8xx-core.c b/drivers/mfd/rk8xx-core.c
index e2261b68b844..c68a380332e7 100644
--- a/drivers/mfd/rk8xx-core.c
+++ b/drivers/mfd/rk8xx-core.c
@@ -28,6 +28,10 @@ static const struct resource rtc_resources[] = {
DEFINE_RES_IRQ(RK808_IRQ_RTC_ALARM),
};
+static const struct resource rk816_rtc_resources[] = {
+ DEFINE_RES_IRQ(RK816_IRQ_RTC_ALARM),
+};
+
static const struct resource rk817_rtc_resources[] = {
DEFINE_RES_IRQ(RK817_IRQ_RTC_ALARM),
};
@@ -87,6 +91,21 @@ static const struct mfd_cell rk808s[] = {
},
};
+static const struct mfd_cell rk816s[] = {
+ { .name = "rk805-pinctrl", },
+ { .name = "rk808-clkout", },
+ { .name = "rk808-regulator", },
+ { .name = "rk805-pwrkey",
+ .num_resources = ARRAY_SIZE(rk805_key_resources),
+ .resources = rk805_key_resources,
+ },
+ {
+ .name = "rk808-rtc",
+ .num_resources = ARRAY_SIZE(rk816_rtc_resources),
+ .resources = rk816_rtc_resources,
+ },
+};
+
static const struct mfd_cell rk817s[] = {
{ .name = "rk808-clkout", },
{ .name = "rk808-regulator", },
@@ -148,6 +167,17 @@ static const struct rk808_reg_data rk808_pre_init_reg[] = {
VB_LO_SEL_3500MV },
};
+static const struct rk808_reg_data rk816_pre_init_reg[] = {
+ { RK818_BUCK1_CONFIG_REG, RK817_RAMP_RATE_MASK,
+ RK817_RAMP_RATE_12_5MV_PER_US },
+ { RK818_BUCK2_CONFIG_REG, RK817_RAMP_RATE_MASK,
+ RK817_RAMP_RATE_12_5MV_PER_US },
+ { RK818_BUCK4_CONFIG_REG, BUCK_ILMIN_MASK, BUCK_ILMIN_250MA },
+ { RK808_THERMAL_REG, TEMP_HOTDIE_MSK, TEMP105C},
+ { RK808_VB_MON_REG, VBAT_LOW_VOL_MASK | VBAT_LOW_ACT_MASK,
+ RK808_VBAT_LOW_3V0 | EN_VABT_LOW_SHUT_DOWN },
+};
+
static const struct rk808_reg_data rk817_pre_init_reg[] = {
{RK817_RTC_CTRL_REG, RTC_STOP, RTC_STOP},
/* Codec specific registers */
@@ -350,6 +380,59 @@ static const struct regmap_irq rk808_irqs[] = {
},
};
+static const unsigned int rk816_irq_status_offsets[] = {
+ (RK816_INT_STS_REG1 - RK816_INT_STS_REG1),
+ (RK816_INT_STS_REG2 - RK816_INT_STS_REG1),
+ (RK816_INT_STS_REG3 - RK816_INT_STS_REG1),
+};
+
+static const unsigned int rk816_irq_mask_offsets[] = {
+ (RK816_INT_STS_MSK_REG1 - RK816_INT_STS_MSK_REG1),
+ (RK816_INT_STS_MSK_REG2 - RK816_INT_STS_MSK_REG1),
+ (RK816_INT_STS_MSK_REG3 - RK816_INT_STS_MSK_REG1),
+};
+
+static unsigned int rk816_get_irq_reg(struct regmap_irq_chip_data *data,
+ unsigned int base, int index)
+{
+ unsigned int irq_reg = base;
+
+ switch (base) {
+ case RK816_INT_STS_REG1:
+ irq_reg += rk816_irq_status_offsets[index];
+ break;
+ case RK816_INT_STS_MSK_REG1:
+ irq_reg += rk816_irq_mask_offsets[index];
+ break;
+ }
+
+ return irq_reg;
+};
+
+static const struct regmap_irq rk816_irqs[] = {
+ /* INT_STS_REG1 IRQs */
+ REGMAP_IRQ_REG(RK816_IRQ_PWRON_FALL, 0, RK816_INT_STS_PWRON_FALL),
+ REGMAP_IRQ_REG(RK816_IRQ_PWRON_RISE, 0, RK816_INT_STS_PWRON_RISE),
+
+ /* INT_STS_REG2 IRQs */
+ REGMAP_IRQ_REG(RK816_IRQ_VB_LOW, 1, RK816_INT_STS_VB_LOW),
+ REGMAP_IRQ_REG(RK816_IRQ_PWRON, 1, RK816_INT_STS_PWRON),
+ REGMAP_IRQ_REG(RK816_IRQ_PWRON_LP, 1, RK816_INT_STS_PWRON_LP),
+ REGMAP_IRQ_REG(RK816_IRQ_HOTDIE, 1, RK816_INT_STS_HOTDIE),
+ REGMAP_IRQ_REG(RK816_IRQ_RTC_ALARM, 1, RK816_INT_STS_RTC_ALARM),
+ REGMAP_IRQ_REG(RK816_IRQ_RTC_PERIOD, 1, RK816_INT_STS_RTC_PERIOD),
+ REGMAP_IRQ_REG(RK816_IRQ_USB_OV, 1, RK816_INT_STS_USB_OV),
+
+ /* INT_STS3 IRQs */
+ REGMAP_IRQ_REG(RK816_IRQ_PLUG_IN, 2, RK816_INT_STS_PLUG_IN),
+ REGMAP_IRQ_REG(RK816_IRQ_PLUG_OUT, 2, RK816_INT_STS_PLUG_OUT),
+ REGMAP_IRQ_REG(RK816_IRQ_CHG_OK, 2, RK816_INT_STS_CHG_OK),
+ REGMAP_IRQ_REG(RK816_IRQ_CHG_TE, 2, RK816_INT_STS_CHG_TE),
+ REGMAP_IRQ_REG(RK816_IRQ_CHG_TS, 2, RK816_INT_STS_CHG_TS),
+ REGMAP_IRQ_REG(RK816_IRQ_CHG_CVTLIM, 2, RK816_INT_STS_CHG_CVTLIM),
+ REGMAP_IRQ_REG(RK816_IRQ_DISCHG_ILIM, 2, RK816_INT_STS_DISCHG_ILIM),
+};
+
static const struct regmap_irq rk818_irqs[] = {
/* INT_STS */
[RK818_IRQ_VOUT_LO] = {
@@ -482,6 +565,18 @@ static const struct regmap_irq_chip rk808_irq_chip = {
.init_ack_masked = true,
};
+static const struct regmap_irq_chip rk816_irq_chip = {
+ .name = "rk816",
+ .irqs = rk816_irqs,
+ .num_irqs = ARRAY_SIZE(rk816_irqs),
+ .num_regs = 3,
+ .get_irq_reg = rk816_get_irq_reg,
+ .status_base = RK816_INT_STS_REG1,
+ .mask_base = RK816_INT_STS_MSK_REG1,
+ .ack_base = RK816_INT_STS_REG1,
+ .init_ack_masked = true,
+};
+
static struct regmap_irq_chip rk817_irq_chip = {
.name = "rk817",
.irqs = rk817_irqs,
@@ -530,6 +625,7 @@ static int rk808_power_off(struct sys_off_data *data)
reg = RK817_SYS_CFG(3);
bit = DEV_OFF;
break;
+ case RK816_ID:
case RK818_ID:
reg = RK818_DEVCTRL_REG;
bit = DEV_OFF;
@@ -637,6 +733,13 @@ int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap
cells = rk808s;
nr_cells = ARRAY_SIZE(rk808s);
break;
+ case RK816_ID:
+ rk808->regmap_irq_chip = &rk816_irq_chip;
+ pre_init_reg = rk816_pre_init_reg;
+ nr_pre_init_regs = ARRAY_SIZE(rk816_pre_init_reg);
+ cells = rk816s;
+ nr_cells = ARRAY_SIZE(rk816s);
+ break;
case RK818_ID:
rk808->regmap_irq_chip = &rk818_irq_chip;
pre_init_reg = rk818_pre_init_reg;
diff --git a/drivers/mfd/rk8xx-i2c.c b/drivers/mfd/rk8xx-i2c.c
index 75b5cf09d5a0..69a6b297d723 100644
--- a/drivers/mfd/rk8xx-i2c.c
+++ b/drivers/mfd/rk8xx-i2c.c
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0-only
/*
- * Rockchip RK808/RK818 Core (I2C) driver
+ * Rockchip RK805/RK808/RK816/RK817/RK818 Core (I2C) driver
*
* Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
* Copyright (C) 2016 PHYTEC Messtechnik GmbH
@@ -49,6 +49,35 @@ static bool rk808_is_volatile_reg(struct device *dev, unsigned int reg)
return false;
}
+static bool rk816_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+ /*
+ * Technically the ROUND_30s bit makes RTC_CTRL_REG volatile, but
+ * we don't use that feature. It's better to cache.
+ */
+
+ switch (reg) {
+ case RK808_SECONDS_REG ... RK808_WEEKS_REG:
+ case RK808_RTC_STATUS_REG:
+ case RK808_VB_MON_REG:
+ case RK808_THERMAL_REG:
+ case RK816_DCDC_EN_REG1:
+ case RK816_DCDC_EN_REG2:
+ case RK816_INT_STS_REG1:
+ case RK816_INT_STS_REG2:
+ case RK816_INT_STS_REG3:
+ case RK808_DEVCTRL_REG:
+ case RK816_SUP_STS_REG:
+ case RK816_GGSTS_REG:
+ case RK816_ZERO_CUR_ADC_REGH:
+ case RK816_ZERO_CUR_ADC_REGL:
+ case RK816_GASCNT_REG(0) ... RK816_BAT_VOL_REGL:
+ return true;
+ }
+
+ return false;
+}
+
static bool rk817_is_volatile_reg(struct device *dev, unsigned int reg)
{
/*
@@ -100,6 +129,14 @@ static const struct regmap_config rk808_regmap_config = {
.volatile_reg = rk808_is_volatile_reg,
};
+static const struct regmap_config rk816_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = RK816_DATA_REG(18),
+ .cache_type = REGCACHE_MAPLE,
+ .volatile_reg = rk816_is_volatile_reg,
+};
+
static const struct regmap_config rk817_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
@@ -123,6 +160,11 @@ static const struct rk8xx_i2c_platform_data rk809_data = {
.variant = RK809_ID,
};
+static const struct rk8xx_i2c_platform_data rk816_data = {
+ .regmap_cfg = &rk816_regmap_config,
+ .variant = RK816_ID,
+};
+
static const struct rk8xx_i2c_platform_data rk817_data = {
.regmap_cfg = &rk817_regmap_config,
.variant = RK817_ID,
@@ -161,6 +203,7 @@ static const struct of_device_id rk8xx_i2c_of_match[] = {
{ .compatible = "rockchip,rk805", .data = &rk805_data },
{ .compatible = "rockchip,rk808", .data = &rk808_data },
{ .compatible = "rockchip,rk809", .data = &rk809_data },
+ { .compatible = "rockchip,rk816", .data = &rk816_data },
{ .compatible = "rockchip,rk817", .data = &rk817_data },
{ .compatible = "rockchip,rk818", .data = &rk818_data },
{ },
diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
index 78e167a92483..b90d1c278790 100644
--- a/include/linux/mfd/rk808.h
+++ b/include/linux/mfd/rk808.h
@@ -113,6 +113,145 @@ enum rk808_reg {
#define RK808_INT_STS_MSK_REG2 0x4f
#define RK808_IO_POL_REG 0x50
+/* RK816 */
+enum rk816_reg {
+ RK816_ID_DCDC1,
+ RK816_ID_DCDC2,
+ RK816_ID_DCDC3,
+ RK816_ID_DCDC4,
+ RK816_ID_LDO1,
+ RK816_ID_LDO2,
+ RK816_ID_LDO3,
+ RK816_ID_LDO4,
+ RK816_ID_LDO5,
+ RK816_ID_LDO6,
+ RK816_ID_BOOST,
+ RK816_ID_OTG_SW,
+};
+
+enum rk816_irqs {
+ /* INT_STS_REG1 */
+ RK816_IRQ_PWRON_FALL,
+ RK816_IRQ_PWRON_RISE,
+
+ /* INT_STS_REG2 */
+ RK816_IRQ_VB_LOW,
+ RK816_IRQ_PWRON,
+ RK816_IRQ_PWRON_LP,
+ RK816_IRQ_HOTDIE,
+ RK816_IRQ_RTC_ALARM,
+ RK816_IRQ_RTC_PERIOD,
+ RK816_IRQ_USB_OV,
+
+ /* INT_STS_REG3 */
+ RK816_IRQ_PLUG_IN,
+ RK816_IRQ_PLUG_OUT,
+ RK816_IRQ_CHG_OK,
+ RK816_IRQ_CHG_TE,
+ RK816_IRQ_CHG_TS,
+ RK816_IRQ_CHG_CVTLIM,
+ RK816_IRQ_DISCHG_ILIM,
+};
+
+/* power channel registers */
+#define RK816_DCDC_EN_REG1 0x23
+
+#define RK816_DCDC_EN_REG2 0x24
+#define RK816_BOOST_EN BIT(1)
+#define RK816_OTG_EN BIT(2)
+#define RK816_BOOST_EN_MSK BIT(5)
+#define RK816_OTG_EN_MSK BIT(6)
+#define RK816_BUCK_DVS_CONFIRM BIT(7)
+
+#define RK816_LDO_EN_REG1 0x27
+
+#define RK816_LDO_EN_REG2 0x28
+
+/* interrupt registers and irq definitions */
+#define RK816_INT_STS_REG1 0x49
+#define RK816_INT_STS_MSK_REG1 0x4a
+#define RK816_INT_STS_PWRON_FALL BIT(5)
+#define RK816_INT_STS_PWRON_RISE BIT(6)
+
+#define RK816_INT_STS_REG2 0x4c
+#define RK816_INT_STS_MSK_REG2 0x4d
+#define RK816_INT_STS_VB_LOW BIT(1)
+#define RK816_INT_STS_PWRON BIT(2)
+#define RK816_INT_STS_PWRON_LP BIT(3)
+#define RK816_INT_STS_HOTDIE BIT(4)
+#define RK816_INT_STS_RTC_ALARM BIT(5)
+#define RK816_INT_STS_RTC_PERIOD BIT(6)
+#define RK816_INT_STS_USB_OV BIT(7)
+
+#define RK816_INT_STS_REG3 0x4e
+#define RK816_INT_STS_MSK_REG3 0x4f
+#define RK816_INT_STS_PLUG_IN BIT(0)
+#define RK816_INT_STS_PLUG_OUT BIT(1)
+#define RK816_INT_STS_CHG_OK BIT(2)
+#define RK816_INT_STS_CHG_TE BIT(3)
+#define RK816_INT_STS_CHG_TS BIT(4)
+#define RK816_INT_STS_CHG_CVTLIM BIT(6)
+#define RK816_INT_STS_DISCHG_ILIM BIT(7)
+
+/* charger, boost and OTG registers */
+#define RK816_OTG_BUCK_LDO_CONFIG_REG 0x2a
+#define RK816_CHRG_CONFIG_REG 0x2b
+#define RK816_BOOST_ON_VESL_REG 0x54
+#define RK816_BOOST_SLP_VSEL_REG 0x55
+#define RK816_CHRG_BOOST_CONFIG_REG 0x9a
+#define RK816_SUP_STS_REG 0xa0
+#define RK816_USB_CTRL_REG 0xa1
+#define RK816_CHRG_CTRL(x) (0xa3 + (x))
+#define RK816_BAT_CTRL_REG 0xa6
+#define RK816_BAT_HTS_TS_REG 0xa8
+#define RK816_BAT_LTS_TS_REG 0xa9
+
+/* adc and fuel gauge registers */
+#define RK816_TS_CTRL_REG 0xac
+#define RK816_ADC_CTRL_REG 0xad
+#define RK816_GGCON_REG 0xb0
+#define RK816_GGSTS_REG 0xb1
+#define RK816_ZERO_CUR_ADC_REGH 0xb2
+#define RK816_ZERO_CUR_ADC_REGL 0xb3
+#define RK816_GASCNT_CAL_REG(x) (0xb7 - (x))
+#define RK816_GASCNT_REG(x) (0xbb - (x))
+#define RK816_BAT_CUR_AVG_REGH 0xbc
+#define RK816_BAT_CUR_AVG_REGL 0xbd
+#define RK816_TS_ADC_REGH 0xbe
+#define RK816_TS_ADC_REGL 0xbf
+#define RK816_USB_ADC_REGH 0xc0
+#define RK816_USB_ADC_REGL 0xc1
+#define RK816_BAT_OCV_REGH 0xc2
+#define RK816_BAT_OCV_REGL 0xc3
+#define RK816_BAT_VOL_REGH 0xc4
+#define RK816_BAT_VOL_REGL 0xc5
+#define RK816_RELAX_ENTRY_THRES_REGH 0xc6
+#define RK816_RELAX_ENTRY_THRES_REGL 0xc7
+#define RK816_RELAX_EXIT_THRES_REGH 0xc8
+#define RK816_RELAX_EXIT_THRES_REGL 0xc9
+#define RK816_RELAX_VOL1_REGH 0xca
+#define RK816_RELAX_VOL1_REGL 0xcb
+#define RK816_RELAX_VOL2_REGH 0xcc
+#define RK816_RELAX_VOL2_REGL 0xcd
+#define RK816_RELAX_CUR1_REGH 0xce
+#define RK816_RELAX_CUR1_REGL 0xcf
+#define RK816_RELAX_CUR2_REGH 0xd0
+#define RK816_RELAX_CUR2_REGL 0xd1
+#define RK816_CAL_OFFSET_REGH 0xd2
+#define RK816_CAL_OFFSET_REGL 0xd3
+#define RK816_NON_ACT_TIMER_CNT_REG 0xd4
+#define RK816_VCALIB0_REGH 0xd5
+#define RK816_VCALIB0_REGL 0xd6
+#define RK816_VCALIB1_REGH 0xd7
+#define RK816_VCALIB1_REGL 0xd8
+#define RK816_FCC_GASCNT_REG(x) (0xdc - (x))
+#define RK816_IOFFSET_REGH 0xdd
+#define RK816_IOFFSET_REGL 0xde
+#define RK816_SLEEP_CON_SAMP_CUR_REG 0xdf
+
+/* general purpose data registers 0xe0 ~ 0xf2 */
+#define RK816_DATA_REG(x) (0xe0 + (x))
+
/* RK818 */
#define RK818_DCDC1 0
#define RK818_LDO1 4
@@ -791,6 +930,7 @@ enum rk806_dvs_mode {
#define VOUT_LO_INT BIT(0)
#define CLK32KOUT2_EN BIT(0)
+#define TEMP105C 0x08
#define TEMP115C 0x0c
#define TEMP_HOTDIE_MSK 0x0c
#define SLP_SD_MSK (0x3 << 2)
@@ -1191,6 +1331,7 @@ enum {
RK806_ID = 0x8060,
RK808_ID = 0x0000,
RK809_ID = 0x8090,
+ RK816_ID = 0x8160,
RK817_ID = 0x8170,
RK818_ID = 0x8180,
};
--
2.43.2
This adds support for RK816 to the exising rk805 pinctrl driver
It has a single pin which can be configured as input from a thermistor (for
instance in an attached battery) or as a gpio.
Signed-off-by: Alex Bee <[email protected]>
---
changes since v1:
- rename pin-function names according to the updated binding
- added missing fun_reg for rk816_gpio_cfgs
changes since v2:
- aligned pin-function names with binding (dropped "pin_fun"-prefix)
drivers/pinctrl/pinctrl-rk805.c | 69 +++++++++++++++++++++++++++++++++
1 file changed, 69 insertions(+)
diff --git a/drivers/pinctrl/pinctrl-rk805.c b/drivers/pinctrl/pinctrl-rk805.c
index 56d916f2cee6..c42f1bf93404 100644
--- a/drivers/pinctrl/pinctrl-rk805.c
+++ b/drivers/pinctrl/pinctrl-rk805.c
@@ -93,6 +93,11 @@ enum rk806_pinmux_option {
RK806_PINMUX_FUN5,
};
+enum rk816_pinmux_option {
+ RK816_PINMUX_THERMISTOR,
+ RK816_PINMUX_GPIO,
+};
+
enum {
RK805_GPIO0,
RK805_GPIO1,
@@ -104,6 +109,10 @@ enum {
RK806_GPIO_DVS3
};
+enum {
+ RK816_GPIO0,
+};
+
static const char *const rk805_gpio_groups[] = {
"gpio0",
"gpio1",
@@ -115,6 +124,10 @@ static const char *const rk806_gpio_groups[] = {
"gpio_pwrctrl3",
};
+static const char *const rk816_gpio_groups[] = {
+ "gpio0",
+};
+
/* RK805: 2 output only GPIOs */
static const struct pinctrl_pin_desc rk805_pins_desc[] = {
PINCTRL_PIN(RK805_GPIO0, "gpio0"),
@@ -128,6 +141,11 @@ static const struct pinctrl_pin_desc rk806_pins_desc[] = {
PINCTRL_PIN(RK806_GPIO_DVS3, "gpio_pwrctrl3"),
};
+/* RK816 */
+static const struct pinctrl_pin_desc rk816_pins_desc[] = {
+ PINCTRL_PIN(RK816_GPIO0, "gpio0"),
+};
+
static const struct rk805_pin_function rk805_pin_functions[] = {
{
.name = "gpio",
@@ -176,6 +194,21 @@ static const struct rk805_pin_function rk806_pin_functions[] = {
},
};
+static const struct rk805_pin_function rk816_pin_functions[] = {
+ {
+ .name = "gpio",
+ .groups = rk816_gpio_groups,
+ .ngroups = ARRAY_SIZE(rk816_gpio_groups),
+ .mux_option = RK816_PINMUX_GPIO,
+ },
+ {
+ .name = "thermistor",
+ .groups = rk816_gpio_groups,
+ .ngroups = ARRAY_SIZE(rk816_gpio_groups),
+ .mux_option = RK816_PINMUX_THERMISTOR,
+ },
+};
+
static const struct rk805_pin_group rk805_pin_groups[] = {
{
.name = "gpio0",
@@ -207,6 +240,14 @@ static const struct rk805_pin_group rk806_pin_groups[] = {
}
};
+static const struct rk805_pin_group rk816_pin_groups[] = {
+ {
+ .name = "gpio0",
+ .pins = { RK816_GPIO0 },
+ .npins = 1,
+ },
+};
+
#define RK805_GPIO0_VAL_MSK BIT(0)
#define RK805_GPIO1_VAL_MSK BIT(1)
@@ -255,6 +296,20 @@ static struct rk805_pin_config rk806_gpio_cfgs[] = {
}
};
+#define RK816_FUN_MASK BIT(2)
+#define RK816_VAL_MASK BIT(3)
+#define RK816_DIR_MASK BIT(4)
+
+static struct rk805_pin_config rk816_gpio_cfgs[] = {
+ {
+ .fun_reg = RK818_IO_POL_REG,
+ .fun_msk = RK816_FUN_MASK,
+ .reg = RK818_IO_POL_REG,
+ .val_msk = RK816_VAL_MASK,
+ .dir_msk = RK816_DIR_MASK,
+ },
+};
+
/* generic gpio chip */
static int rk805_gpio_get(struct gpio_chip *chip, unsigned int offset)
{
@@ -439,6 +494,8 @@ static int rk805_pinctrl_gpio_request_enable(struct pinctrl_dev *pctldev,
return _rk805_pinctrl_set_mux(pctldev, offset, RK805_PINMUX_GPIO);
case RK806_ID:
return _rk805_pinctrl_set_mux(pctldev, offset, RK806_PINMUX_FUN5);
+ case RK816_ID:
+ return _rk805_pinctrl_set_mux(pctldev, offset, RK816_PINMUX_GPIO);
}
return -ENOTSUPP;
@@ -588,6 +645,18 @@ static int rk805_pinctrl_probe(struct platform_device *pdev)
pci->pin_cfg = rk806_gpio_cfgs;
pci->gpio_chip.ngpio = ARRAY_SIZE(rk806_gpio_cfgs);
break;
+ case RK816_ID:
+ pci->pins = rk816_pins_desc;
+ pci->num_pins = ARRAY_SIZE(rk816_pins_desc);
+ pci->functions = rk816_pin_functions;
+ pci->num_functions = ARRAY_SIZE(rk816_pin_functions);
+ pci->groups = rk816_pin_groups;
+ pci->num_pin_groups = ARRAY_SIZE(rk816_pin_groups);
+ pci->pinctrl_desc.pins = rk816_pins_desc;
+ pci->pinctrl_desc.npins = ARRAY_SIZE(rk816_pins_desc);
+ pci->pin_cfg = rk816_gpio_cfgs;
+ pci->gpio_chip.ngpio = ARRAY_SIZE(rk816_gpio_cfgs);
+ break;
default:
dev_err(&pdev->dev, "unsupported RK805 ID %lu\n",
pci->rk808->variant);
--
2.43.2
rk808_set_suspend_voltage_range currently does not account the existence of
apply_bit/apply_reg.
This adds support for those in same way it is done in
regulator_set_voltage_sel_regmap and is required for the upcoming RK816
support
Signed-off-by: Alex Bee <[email protected]>
---
changes since v1:
- none
drivers/regulator/rk808-regulator.c | 16 +++++++++++++---
1 file changed, 13 insertions(+), 3 deletions(-)
diff --git a/drivers/regulator/rk808-regulator.c b/drivers/regulator/rk808-regulator.c
index d89ae7f16d7a..a6a563e402d0 100644
--- a/drivers/regulator/rk808-regulator.c
+++ b/drivers/regulator/rk808-regulator.c
@@ -534,15 +534,25 @@ static int rk808_set_suspend_voltage_range(struct regulator_dev *rdev, int uv)
{
unsigned int reg;
int sel = regulator_map_voltage_linear_range(rdev, uv, uv);
+ int ret;
if (sel < 0)
return -EINVAL;
reg = rdev->desc->vsel_reg + RK808_SLP_REG_OFFSET;
- return regmap_update_bits(rdev->regmap, reg,
- rdev->desc->vsel_mask,
- sel);
+ ret = regmap_update_bits(rdev->regmap, reg,
+ rdev->desc->vsel_mask,
+ sel);
+ if (ret)
+ return ret;
+
+ if (rdev->desc->apply_bit)
+ ret = regmap_update_bits(rdev->regmap, rdev->desc->apply_reg,
+ rdev->desc->apply_bit,
+ rdev->desc->apply_bit);
+
+ return ret;
}
static int rk805_set_suspend_enable(struct regulator_dev *rdev)
--
2.43.2
Add support for rk816 to the existing rk808 regulator driver.
The infrastructure of the driver can be re-used as is. A peculiarity for
this version is, that BUCK1/BUCK2 have a (common) bit which needs to
toggled after a voltage change to confirm the change. Regulator regmap
takes care of that by defining a apply_bit and apply_reg for those
regulators.
Signed-off-by: Alex Bee <[email protected]>
---
changes since v1:
- align regulator's .name and .of_match with updated binding
changes since v2:
- align regulator's .name and .of_match with updated binding
(dropped "-regulator" prefix)
drivers/regulator/rk808-regulator.c | 202 +++++++++++++++++++++++++++-
1 file changed, 201 insertions(+), 1 deletion(-)
diff --git a/drivers/regulator/rk808-regulator.c b/drivers/regulator/rk808-regulator.c
index a6a563e402d0..14b60abd6afc 100644
--- a/drivers/regulator/rk808-regulator.c
+++ b/drivers/regulator/rk808-regulator.c
@@ -158,6 +158,11 @@
RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg, \
_vmask, _ereg, _emask, 0, 0, _etime, &rk808_reg_ops)
+#define RK816_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \
+ _vmask, _ereg, _emask, _disval, _etime) \
+ RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg, \
+ _vmask, _ereg, _emask, _emask, _disval, _etime, &rk816_reg_ops)
+
#define RK817_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \
_vmask, _ereg, _emask, _disval, _etime) \
RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg, \
@@ -258,7 +263,7 @@ static const unsigned int rk808_buck1_2_ramp_table[] = {
2000, 4000, 6000, 10000
};
-/* RK817 RK809 */
+/* RK817/RK809/RK816 (buck 1/2 only) */
static const unsigned int rk817_buck1_4_ramp_table[] = {
3000, 6300, 12500, 25000
};
@@ -640,6 +645,38 @@ static int rk808_set_suspend_disable(struct regulator_dev *rdev)
rdev->desc->enable_mask);
}
+static const struct rk8xx_register_bit rk816_suspend_bits[] = {
+ RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 0),
+ RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 1),
+ RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 2),
+ RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 3),
+ RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 0),
+ RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 1),
+ RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 2),
+ RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 3),
+ RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 4),
+ RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 5),
+ RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 5),
+ RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 6),
+};
+
+static int rk816_set_suspend_enable(struct regulator_dev *rdev)
+{
+ int rid = rdev_get_id(rdev);
+
+ return regmap_update_bits(rdev->regmap, rk816_suspend_bits[rid].reg,
+ rk816_suspend_bits[rid].bit,
+ rk816_suspend_bits[rid].bit);
+}
+
+static int rk816_set_suspend_disable(struct regulator_dev *rdev)
+{
+ int rid = rdev_get_id(rdev);
+
+ return regmap_update_bits(rdev->regmap, rk816_suspend_bits[rid].reg,
+ rk816_suspend_bits[rid].bit, 0);
+}
+
static int rk817_set_suspend_enable_ctrl(struct regulator_dev *rdev,
unsigned int en)
{
@@ -913,6 +950,54 @@ static const struct regulator_ops rk809_buck5_ops_range = {
.set_suspend_disable = rk817_set_suspend_disable,
};
+static const struct regulator_ops rk816_buck1_2_ops_ranges = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .set_mode = rk8xx_set_mode,
+ .get_mode = rk8xx_get_mode,
+ .set_suspend_mode = rk8xx_set_suspend_mode,
+ .set_ramp_delay = regulator_set_ramp_delay_regmap,
+ .set_suspend_voltage = rk808_set_suspend_voltage_range,
+ .set_suspend_enable = rk816_set_suspend_enable,
+ .set_suspend_disable = rk816_set_suspend_disable,
+};
+
+static const struct regulator_ops rk816_buck4_ops_ranges = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .set_mode = rk8xx_set_mode,
+ .get_mode = rk8xx_get_mode,
+ .set_suspend_mode = rk8xx_set_suspend_mode,
+ .set_suspend_voltage = rk808_set_suspend_voltage_range,
+ .set_suspend_enable = rk816_set_suspend_enable,
+ .set_suspend_disable = rk816_set_suspend_disable,
+};
+
+static const struct regulator_ops rk816_reg_ops = {
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = rk8xx_is_enabled_wmsk_regmap,
+ .set_suspend_voltage = rk808_set_suspend_voltage,
+ .set_suspend_enable = rk816_set_suspend_enable,
+ .set_suspend_disable = rk816_set_suspend_disable,
+};
+
static const struct regulator_ops rk817_reg_ops = {
.list_voltage = regulator_list_voltage_linear,
.map_voltage = regulator_map_voltage_linear,
@@ -1392,6 +1477,117 @@ static const struct regulator_desc rk809_reg[] = {
DISABLE_VAL(3)),
};
+static const struct linear_range rk816_buck_4_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(800000, 0, 26, 100000),
+ REGULATOR_LINEAR_RANGE(3500000, 27, 31, 0),
+};
+
+static const struct regulator_desc rk816_reg[] = {
+ {
+ .name = "dcdc1",
+ .supply_name = "vcc1",
+ .of_match = of_match_ptr("dcdc1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = RK816_ID_DCDC1,
+ .ops = &rk816_buck1_2_ops_ranges,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = 64,
+ .linear_ranges = rk805_buck_1_2_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(rk805_buck_1_2_voltage_ranges),
+ .vsel_reg = RK818_BUCK1_ON_VSEL_REG,
+ .vsel_mask = RK818_BUCK_VSEL_MASK,
+ .apply_reg = RK816_DCDC_EN_REG2,
+ .apply_bit = RK816_BUCK_DVS_CONFIRM,
+ .enable_reg = RK816_DCDC_EN_REG1,
+ .enable_mask = BIT(4) | BIT(0),
+ .enable_val = BIT(4) | BIT(0),
+ .disable_val = BIT(4),
+ .ramp_reg = RK818_BUCK1_CONFIG_REG,
+ .ramp_mask = RK808_RAMP_RATE_MASK,
+ .ramp_delay_table = rk817_buck1_4_ramp_table,
+ .n_ramp_values = ARRAY_SIZE(rk817_buck1_4_ramp_table),
+ .of_map_mode = rk8xx_regulator_of_map_mode,
+ .owner = THIS_MODULE,
+ }, {
+ .name = "dcdc2",
+ .supply_name = "vcc2",
+ .of_match = of_match_ptr("dcdc2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = RK816_ID_DCDC2,
+ .ops = &rk816_buck1_2_ops_ranges,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = 64,
+ .linear_ranges = rk805_buck_1_2_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(rk805_buck_1_2_voltage_ranges),
+ .vsel_reg = RK818_BUCK2_ON_VSEL_REG,
+ .vsel_mask = RK818_BUCK_VSEL_MASK,
+ .apply_reg = RK816_DCDC_EN_REG2,
+ .apply_bit = RK816_BUCK_DVS_CONFIRM,
+ .enable_reg = RK816_DCDC_EN_REG1,
+ .enable_mask = BIT(5) | BIT(1),
+ .enable_val = BIT(5) | BIT(1),
+ .disable_val = BIT(5),
+ .ramp_reg = RK818_BUCK2_CONFIG_REG,
+ .ramp_mask = RK808_RAMP_RATE_MASK,
+ .ramp_delay_table = rk817_buck1_4_ramp_table,
+ .n_ramp_values = ARRAY_SIZE(rk817_buck1_4_ramp_table),
+ .of_map_mode = rk8xx_regulator_of_map_mode,
+ .owner = THIS_MODULE,
+ }, {
+ .name = "dcdc3",
+ .supply_name = "vcc3",
+ .of_match = of_match_ptr("dcdc3"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = RK816_ID_DCDC3,
+ .ops = &rk808_switch_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = 1,
+ .enable_reg = RK816_DCDC_EN_REG1,
+ .enable_mask = BIT(6) | BIT(2),
+ .enable_val = BIT(6) | BIT(2),
+ .disable_val = BIT(6),
+ .of_map_mode = rk8xx_regulator_of_map_mode,
+ .owner = THIS_MODULE,
+ }, {
+ .name = "dcdc4",
+ .supply_name = "vcc4",
+ .of_match = of_match_ptr("dcdc4"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = RK816_ID_DCDC4,
+ .ops = &rk816_buck4_ops_ranges,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = 32,
+ .linear_ranges = rk816_buck_4_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(rk816_buck_4_voltage_ranges),
+ .vsel_reg = RK818_BUCK4_ON_VSEL_REG,
+ .vsel_mask = RK818_BUCK4_VSEL_MASK,
+ .enable_reg = RK816_DCDC_EN_REG1,
+ .enable_mask = BIT(7) | BIT(3),
+ .enable_val = BIT(7) | BIT(3),
+ .disable_val = BIT(7),
+ .of_map_mode = rk8xx_regulator_of_map_mode,
+ .owner = THIS_MODULE,
+ },
+ RK816_DESC(RK816_ID_LDO1, "ldo1", "vcc5", 800, 3400, 100,
+ RK818_LDO1_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+ RK816_LDO_EN_REG1, ENABLE_MASK(0), DISABLE_VAL(0), 400),
+ RK816_DESC(RK816_ID_LDO2, "ldo2", "vcc5", 800, 3400, 100,
+ RK818_LDO2_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+ RK816_LDO_EN_REG1, ENABLE_MASK(1), DISABLE_VAL(1), 400),
+ RK816_DESC(RK816_ID_LDO3, "ldo3", "vcc5", 800, 3400, 100,
+ RK818_LDO3_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+ RK816_LDO_EN_REG1, ENABLE_MASK(2), DISABLE_VAL(2), 400),
+ RK816_DESC(RK816_ID_LDO4, "ldo4", "vcc6", 800, 3400, 100,
+ RK818_LDO4_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+ RK816_LDO_EN_REG1, ENABLE_MASK(3), DISABLE_VAL(3), 400),
+ RK816_DESC(RK816_ID_LDO5, "ldo5", "vcc6", 800, 3400, 100,
+ RK818_LDO5_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+ RK816_LDO_EN_REG2, ENABLE_MASK(0), DISABLE_VAL(0), 400),
+ RK816_DESC(RK816_ID_LDO6, "ldo6", "vcc6", 800, 3400, 100,
+ RK818_LDO6_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+ RK816_LDO_EN_REG2, ENABLE_MASK(1), DISABLE_VAL(1), 400),
+};
+
static const struct regulator_desc rk817_reg[] = {
{
.name = "DCDC_REG1",
@@ -1714,6 +1910,10 @@ static int rk808_regulator_probe(struct platform_device *pdev)
regulators = rk809_reg;
nregulators = RK809_NUM_REGULATORS;
break;
+ case RK816_ID:
+ regulators = rk816_reg;
+ nregulators = ARRAY_SIZE(rk816_reg);
+ break;
case RK817_ID:
regulators = rk817_reg;
nregulators = RK817_NUM_REGULATORS;
--
2.43.2
On 23/03/2024 14:27, Alex Bee wrote:
> Add DT binding document for Rockchip's RK816 PMIC
>
> Signed-off-by: Alex Bee <[email protected]>
> + regulators:
> + type: object
> + patternProperties:
> + '^(boost|dcdc[1-4]|ldo[1-6]|otg-switch)$':
> + type: object
> + $ref: /schemas/regulator/regulator.yaml#
> + unevaluatedProperties: false
This is good.
> + unevaluatedProperties: false
I missed it last time, apologies. This (second) unevaluated should be
"additionalProperties: false" instead.
With this fixed:
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Best regards,
Krzysztof
Am 23.03.24 um 15:32 schrieb Krzysztof Kozlowski:
> On 23/03/2024 14:27, Alex Bee wrote:
>> Add DT binding document for Rockchip's RK816 PMIC
>>
>> Signed-off-by: Alex Bee <[email protected]>
>
>> + regulators:
>> + type: object
>> + patternProperties:
>> + '^(boost|dcdc[1-4]|ldo[1-6]|otg-switch)$':
>> + type: object
>> + $ref: /schemas/regulator/regulator.yaml#
>> + unevaluatedProperties: false
> This is good.
>
>> + unevaluatedProperties: false
> I missed it last time, apologies. This (second) unevaluated should be
> "additionalProperties: false" instead.
Alright. Since there are no driver changes required for this change, I'll
give the other maintainers some time to review and fix it alongside in v4.
Alex
> With this fixed:
>
> Reviewed-by: Krzysztof Kozlowski <[email protected]>
>
>
> Best regards,
> Krzysztof
>
On Sat, 23 Mar 2024, Alex Bee wrote:
> This integrates RK816 support in the this existing rk8xx mfd driver.
>
> This version has unaligned interrupt registers, which requires to define a
> separate get_irq_reg callback for the regmap. Apart from that the
> integration is straightforward and the existing structures can be used as
> is. The initialization sequence has been taken from vendor kernel.
>
> Signed-off-by: Alex Bee <[email protected]>
> ---
> chnages since v1:
> - un-constify rk816_get_irq_reg's return type
>
> drivers/mfd/Kconfig | 4 +-
> drivers/mfd/rk8xx-core.c | 103 ++++++++++++++++++++++++++++
> drivers/mfd/rk8xx-i2c.c | 45 +++++++++++-
> include/linux/mfd/rk808.h | 141 ++++++++++++++++++++++++++++++++++++++
> 4 files changed, 290 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 4b023ee229cf..2e7286cc98e4 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -1225,7 +1225,7 @@ config MFD_RK8XX
> select MFD_CORE
>
> config MFD_RK8XX_I2C
> - tristate "Rockchip RK805/RK808/RK809/RK817/RK818 Power Management Chip"
> + tristate "Rockchip RK805/RK808/RK809/RK816/RK817/RK818 Power Management Chip"
> depends on I2C && OF
> select MFD_CORE
> select REGMAP_I2C
> @@ -1233,7 +1233,7 @@ config MFD_RK8XX_I2C
> select MFD_RK8XX
> help
> If you say yes here you get support for the RK805, RK808, RK809,
> - RK817 and RK818 Power Management chips.
> + RK816, RK817 and RK818 Power Management chips.
> This driver provides common support for accessing the device
> through I2C interface. The device supports multiple sub-devices
> including interrupts, RTC, LDO & DCDC regulators, and onkey.
> diff --git a/drivers/mfd/rk8xx-core.c b/drivers/mfd/rk8xx-core.c
> index e2261b68b844..c68a380332e7 100644
> --- a/drivers/mfd/rk8xx-core.c
> +++ b/drivers/mfd/rk8xx-core.c
> @@ -28,6 +28,10 @@ static const struct resource rtc_resources[] = {
> DEFINE_RES_IRQ(RK808_IRQ_RTC_ALARM),
> };
>
> +static const struct resource rk816_rtc_resources[] = {
> + DEFINE_RES_IRQ(RK816_IRQ_RTC_ALARM),
> +};
> +
> static const struct resource rk817_rtc_resources[] = {
> DEFINE_RES_IRQ(RK817_IRQ_RTC_ALARM),
> };
> @@ -87,6 +91,21 @@ static const struct mfd_cell rk808s[] = {
> },
> };
>
> +static const struct mfd_cell rk816s[] = {
> + { .name = "rk805-pinctrl", },
> + { .name = "rk808-clkout", },
> + { .name = "rk808-regulator", },
> + { .name = "rk805-pwrkey",
Newline after the '{'.
> + .num_resources = ARRAY_SIZE(rk805_key_resources),
> + .resources = rk805_key_resources,
> + },
> + {
> + .name = "rk808-rtc",
> + .num_resources = ARRAY_SIZE(rk816_rtc_resources),
> + .resources = rk816_rtc_resources,
> + },
> +};
> +
> static const struct mfd_cell rk817s[] = {
> { .name = "rk808-clkout", },
> { .name = "rk808-regulator", },
> @@ -148,6 +167,17 @@ static const struct rk808_reg_data rk808_pre_init_reg[] = {
> VB_LO_SEL_3500MV },
> };
>
> +static const struct rk808_reg_data rk816_pre_init_reg[] = {
> + { RK818_BUCK1_CONFIG_REG, RK817_RAMP_RATE_MASK,
> + RK817_RAMP_RATE_12_5MV_PER_US },
> + { RK818_BUCK2_CONFIG_REG, RK817_RAMP_RATE_MASK,
> + RK817_RAMP_RATE_12_5MV_PER_US },
> + { RK818_BUCK4_CONFIG_REG, BUCK_ILMIN_MASK, BUCK_ILMIN_250MA },
> + { RK808_THERMAL_REG, TEMP_HOTDIE_MSK, TEMP105C},
> + { RK808_VB_MON_REG, VBAT_LOW_VOL_MASK | VBAT_LOW_ACT_MASK,
> + RK808_VBAT_LOW_3V0 | EN_VABT_LOW_SHUT_DOWN },
> +};
> +
> static const struct rk808_reg_data rk817_pre_init_reg[] = {
> {RK817_RTC_CTRL_REG, RTC_STOP, RTC_STOP},
> /* Codec specific registers */
> @@ -350,6 +380,59 @@ static const struct regmap_irq rk808_irqs[] = {
> },
> };
>
> +static const unsigned int rk816_irq_status_offsets[] = {
> + (RK816_INT_STS_REG1 - RK816_INT_STS_REG1),
Turn this into a macro please.
> + (RK816_INT_STS_REG2 - RK816_INT_STS_REG1),
> + (RK816_INT_STS_REG3 - RK816_INT_STS_REG1),
> +};
> +
> +static const unsigned int rk816_irq_mask_offsets[] = {
> + (RK816_INT_STS_MSK_REG1 - RK816_INT_STS_MSK_REG1),
> + (RK816_INT_STS_MSK_REG2 - RK816_INT_STS_MSK_REG1),
> + (RK816_INT_STS_MSK_REG3 - RK816_INT_STS_MSK_REG1),
> +};
> +
> +static unsigned int rk816_get_irq_reg(struct regmap_irq_chip_data *data,
> + unsigned int base, int index)
> +{
> + unsigned int irq_reg = base;
> +
> + switch (base) {
> + case RK816_INT_STS_REG1:
> + irq_reg += rk816_irq_status_offsets[index];
> + break;
> + case RK816_INT_STS_MSK_REG1:
> + irq_reg += rk816_irq_mask_offsets[index];
> + break;
> + }
> +
> + return irq_reg;
> +};
> +
> +static const struct regmap_irq rk816_irqs[] = {
> + /* INT_STS_REG1 IRQs */
> + REGMAP_IRQ_REG(RK816_IRQ_PWRON_FALL, 0, RK816_INT_STS_PWRON_FALL),
> + REGMAP_IRQ_REG(RK816_IRQ_PWRON_RISE, 0, RK816_INT_STS_PWRON_RISE),
> +
> + /* INT_STS_REG2 IRQs */
> + REGMAP_IRQ_REG(RK816_IRQ_VB_LOW, 1, RK816_INT_STS_VB_LOW),
> + REGMAP_IRQ_REG(RK816_IRQ_PWRON, 1, RK816_INT_STS_PWRON),
> + REGMAP_IRQ_REG(RK816_IRQ_PWRON_LP, 1, RK816_INT_STS_PWRON_LP),
> + REGMAP_IRQ_REG(RK816_IRQ_HOTDIE, 1, RK816_INT_STS_HOTDIE),
> + REGMAP_IRQ_REG(RK816_IRQ_RTC_ALARM, 1, RK816_INT_STS_RTC_ALARM),
> + REGMAP_IRQ_REG(RK816_IRQ_RTC_PERIOD, 1, RK816_INT_STS_RTC_PERIOD),
> + REGMAP_IRQ_REG(RK816_IRQ_USB_OV, 1, RK816_INT_STS_USB_OV),
> +
> + /* INT_STS3 IRQs */
> + REGMAP_IRQ_REG(RK816_IRQ_PLUG_IN, 2, RK816_INT_STS_PLUG_IN),
> + REGMAP_IRQ_REG(RK816_IRQ_PLUG_OUT, 2, RK816_INT_STS_PLUG_OUT),
> + REGMAP_IRQ_REG(RK816_IRQ_CHG_OK, 2, RK816_INT_STS_CHG_OK),
> + REGMAP_IRQ_REG(RK816_IRQ_CHG_TE, 2, RK816_INT_STS_CHG_TE),
> + REGMAP_IRQ_REG(RK816_IRQ_CHG_TS, 2, RK816_INT_STS_CHG_TS),
> + REGMAP_IRQ_REG(RK816_IRQ_CHG_CVTLIM, 2, RK816_INT_STS_CHG_CVTLIM),
> + REGMAP_IRQ_REG(RK816_IRQ_DISCHG_ILIM, 2, RK816_INT_STS_DISCHG_ILIM),
> +};
> +
> static const struct regmap_irq rk818_irqs[] = {
> /* INT_STS */
> [RK818_IRQ_VOUT_LO] = {
> @@ -482,6 +565,18 @@ static const struct regmap_irq_chip rk808_irq_chip = {
> .init_ack_masked = true,
> };
>
> +static const struct regmap_irq_chip rk816_irq_chip = {
> + .name = "rk816",
> + .irqs = rk816_irqs,
> + .num_irqs = ARRAY_SIZE(rk816_irqs),
> + .num_regs = 3,
> + .get_irq_reg = rk816_get_irq_reg,
> + .status_base = RK816_INT_STS_REG1,
> + .mask_base = RK816_INT_STS_MSK_REG1,
> + .ack_base = RK816_INT_STS_REG1,
> + .init_ack_masked = true,
> +};
> +
> static struct regmap_irq_chip rk817_irq_chip = {
> .name = "rk817",
> .irqs = rk817_irqs,
> @@ -530,6 +625,7 @@ static int rk808_power_off(struct sys_off_data *data)
> reg = RK817_SYS_CFG(3);
> bit = DEV_OFF;
> break;
> + case RK816_ID:
> case RK818_ID:
> reg = RK818_DEVCTRL_REG;
> bit = DEV_OFF;
> @@ -637,6 +733,13 @@ int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap
> cells = rk808s;
> nr_cells = ARRAY_SIZE(rk808s);
> break;
> + case RK816_ID:
> + rk808->regmap_irq_chip = &rk816_irq_chip;
> + pre_init_reg = rk816_pre_init_reg;
> + nr_pre_init_regs = ARRAY_SIZE(rk816_pre_init_reg);
> + cells = rk816s;
> + nr_cells = ARRAY_SIZE(rk816s);
> + break;
> case RK818_ID:
> rk808->regmap_irq_chip = &rk818_irq_chip;
> pre_init_reg = rk818_pre_init_reg;
> diff --git a/drivers/mfd/rk8xx-i2c.c b/drivers/mfd/rk8xx-i2c.c
> index 75b5cf09d5a0..69a6b297d723 100644
> --- a/drivers/mfd/rk8xx-i2c.c
> +++ b/drivers/mfd/rk8xx-i2c.c
> @@ -1,6 +1,6 @@
> // SPDX-License-Identifier: GPL-2.0-only
> /*
> - * Rockchip RK808/RK818 Core (I2C) driver
> + * Rockchip RK805/RK808/RK816/RK817/RK818 Core (I2C) driver
> *
> * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
> * Copyright (C) 2016 PHYTEC Messtechnik GmbH
> @@ -49,6 +49,35 @@ static bool rk808_is_volatile_reg(struct device *dev, unsigned int reg)
> return false;
> }
>
> +static bool rk816_is_volatile_reg(struct device *dev, unsigned int reg)
> +{
> + /*
> + * Technically the ROUND_30s bit makes RTC_CTRL_REG volatile, but
> + * we don't use that feature. It's better to cache.
> + */
> +
> + switch (reg) {
> + case RK808_SECONDS_REG ... RK808_WEEKS_REG:
> + case RK808_RTC_STATUS_REG:
> + case RK808_VB_MON_REG:
> + case RK808_THERMAL_REG:
> + case RK816_DCDC_EN_REG1:
> + case RK816_DCDC_EN_REG2:
> + case RK816_INT_STS_REG1:
> + case RK816_INT_STS_REG2:
> + case RK816_INT_STS_REG3:
> + case RK808_DEVCTRL_REG:
> + case RK816_SUP_STS_REG:
> + case RK816_GGSTS_REG:
> + case RK816_ZERO_CUR_ADC_REGH:
> + case RK816_ZERO_CUR_ADC_REGL:
> + case RK816_GASCNT_REG(0) ... RK816_BAT_VOL_REGL:
> + return true;
> + }
> +
> + return false;
> +}
> +
> static bool rk817_is_volatile_reg(struct device *dev, unsigned int reg)
> {
> /*
> @@ -100,6 +129,14 @@ static const struct regmap_config rk808_regmap_config = {
> .volatile_reg = rk808_is_volatile_reg,
> };
>
> +static const struct regmap_config rk816_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .max_register = RK816_DATA_REG(18),
> + .cache_type = REGCACHE_MAPLE,
> + .volatile_reg = rk816_is_volatile_reg,
> +};
> +
> static const struct regmap_config rk817_regmap_config = {
> .reg_bits = 8,
> .val_bits = 8,
> @@ -123,6 +160,11 @@ static const struct rk8xx_i2c_platform_data rk809_data = {
> .variant = RK809_ID,
> };
>
> +static const struct rk8xx_i2c_platform_data rk816_data = {
> + .regmap_cfg = &rk816_regmap_config,
> + .variant = RK816_ID,
> +};
> +
> static const struct rk8xx_i2c_platform_data rk817_data = {
> .regmap_cfg = &rk817_regmap_config,
> .variant = RK817_ID,
> @@ -161,6 +203,7 @@ static const struct of_device_id rk8xx_i2c_of_match[] = {
> { .compatible = "rockchip,rk805", .data = &rk805_data },
> { .compatible = "rockchip,rk808", .data = &rk808_data },
> { .compatible = "rockchip,rk809", .data = &rk809_data },
> + { .compatible = "rockchip,rk816", .data = &rk816_data },
> { .compatible = "rockchip,rk817", .data = &rk817_data },
> { .compatible = "rockchip,rk818", .data = &rk818_data },
> { },
> diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
> index 78e167a92483..b90d1c278790 100644
> --- a/include/linux/mfd/rk808.h
> +++ b/include/linux/mfd/rk808.h
> @@ -113,6 +113,145 @@ enum rk808_reg {
> #define RK808_INT_STS_MSK_REG2 0x4f
> #define RK808_IO_POL_REG 0x50
>
> +/* RK816 */
> +enum rk816_reg {
> + RK816_ID_DCDC1,
> + RK816_ID_DCDC2,
> + RK816_ID_DCDC3,
> + RK816_ID_DCDC4,
> + RK816_ID_LDO1,
> + RK816_ID_LDO2,
> + RK816_ID_LDO3,
> + RK816_ID_LDO4,
> + RK816_ID_LDO5,
> + RK816_ID_LDO6,
> + RK816_ID_BOOST,
> + RK816_ID_OTG_SW,
> +};
> +
> +enum rk816_irqs {
> + /* INT_STS_REG1 */
> + RK816_IRQ_PWRON_FALL,
> + RK816_IRQ_PWRON_RISE,
> +
> + /* INT_STS_REG2 */
> + RK816_IRQ_VB_LOW,
> + RK816_IRQ_PWRON,
> + RK816_IRQ_PWRON_LP,
> + RK816_IRQ_HOTDIE,
> + RK816_IRQ_RTC_ALARM,
> + RK816_IRQ_RTC_PERIOD,
> + RK816_IRQ_USB_OV,
> +
> + /* INT_STS_REG3 */
> + RK816_IRQ_PLUG_IN,
> + RK816_IRQ_PLUG_OUT,
> + RK816_IRQ_CHG_OK,
> + RK816_IRQ_CHG_TE,
> + RK816_IRQ_CHG_TS,
> + RK816_IRQ_CHG_CVTLIM,
> + RK816_IRQ_DISCHG_ILIM,
> +};
> +
> +/* power channel registers */
> +#define RK816_DCDC_EN_REG1 0x23
> +
> +#define RK816_DCDC_EN_REG2 0x24
> +#define RK816_BOOST_EN BIT(1)
> +#define RK816_OTG_EN BIT(2)
> +#define RK816_BOOST_EN_MSK BIT(5)
> +#define RK816_OTG_EN_MSK BIT(6)
> +#define RK816_BUCK_DVS_CONFIRM BIT(7)
> +
> +#define RK816_LDO_EN_REG1 0x27
> +
> +#define RK816_LDO_EN_REG2 0x28
> +
> +/* interrupt registers and irq definitions */
> +#define RK816_INT_STS_REG1 0x49
> +#define RK816_INT_STS_MSK_REG1 0x4a
> +#define RK816_INT_STS_PWRON_FALL BIT(5)
> +#define RK816_INT_STS_PWRON_RISE BIT(6)
> +
> +#define RK816_INT_STS_REG2 0x4c
> +#define RK816_INT_STS_MSK_REG2 0x4d
> +#define RK816_INT_STS_VB_LOW BIT(1)
> +#define RK816_INT_STS_PWRON BIT(2)
> +#define RK816_INT_STS_PWRON_LP BIT(3)
> +#define RK816_INT_STS_HOTDIE BIT(4)
> +#define RK816_INT_STS_RTC_ALARM BIT(5)
> +#define RK816_INT_STS_RTC_PERIOD BIT(6)
> +#define RK816_INT_STS_USB_OV BIT(7)
> +
> +#define RK816_INT_STS_REG3 0x4e
> +#define RK816_INT_STS_MSK_REG3 0x4f
> +#define RK816_INT_STS_PLUG_IN BIT(0)
> +#define RK816_INT_STS_PLUG_OUT BIT(1)
> +#define RK816_INT_STS_CHG_OK BIT(2)
> +#define RK816_INT_STS_CHG_TE BIT(3)
> +#define RK816_INT_STS_CHG_TS BIT(4)
> +#define RK816_INT_STS_CHG_CVTLIM BIT(6)
> +#define RK816_INT_STS_DISCHG_ILIM BIT(7)
> +
> +/* charger, boost and OTG registers */
> +#define RK816_OTG_BUCK_LDO_CONFIG_REG 0x2a
> +#define RK816_CHRG_CONFIG_REG 0x2b
> +#define RK816_BOOST_ON_VESL_REG 0x54
> +#define RK816_BOOST_SLP_VSEL_REG 0x55
> +#define RK816_CHRG_BOOST_CONFIG_REG 0x9a
> +#define RK816_SUP_STS_REG 0xa0
> +#define RK816_USB_CTRL_REG 0xa1
> +#define RK816_CHRG_CTRL(x) (0xa3 + (x))
> +#define RK816_BAT_CTRL_REG 0xa6
> +#define RK816_BAT_HTS_TS_REG 0xa8
> +#define RK816_BAT_LTS_TS_REG 0xa9
> +
> +/* adc and fuel gauge registers */
> +#define RK816_TS_CTRL_REG 0xac
> +#define RK816_ADC_CTRL_REG 0xad
> +#define RK816_GGCON_REG 0xb0
> +#define RK816_GGSTS_REG 0xb1
> +#define RK816_ZERO_CUR_ADC_REGH 0xb2
> +#define RK816_ZERO_CUR_ADC_REGL 0xb3
> +#define RK816_GASCNT_CAL_REG(x) (0xb7 - (x))
> +#define RK816_GASCNT_REG(x) (0xbb - (x))
> +#define RK816_BAT_CUR_AVG_REGH 0xbc
> +#define RK816_BAT_CUR_AVG_REGL 0xbd
> +#define RK816_TS_ADC_REGH 0xbe
> +#define RK816_TS_ADC_REGL 0xbf
> +#define RK816_USB_ADC_REGH 0xc0
> +#define RK816_USB_ADC_REGL 0xc1
> +#define RK816_BAT_OCV_REGH 0xc2
> +#define RK816_BAT_OCV_REGL 0xc3
> +#define RK816_BAT_VOL_REGH 0xc4
> +#define RK816_BAT_VOL_REGL 0xc5
> +#define RK816_RELAX_ENTRY_THRES_REGH 0xc6
> +#define RK816_RELAX_ENTRY_THRES_REGL 0xc7
> +#define RK816_RELAX_EXIT_THRES_REGH 0xc8
> +#define RK816_RELAX_EXIT_THRES_REGL 0xc9
> +#define RK816_RELAX_VOL1_REGH 0xca
> +#define RK816_RELAX_VOL1_REGL 0xcb
> +#define RK816_RELAX_VOL2_REGH 0xcc
> +#define RK816_RELAX_VOL2_REGL 0xcd
> +#define RK816_RELAX_CUR1_REGH 0xce
> +#define RK816_RELAX_CUR1_REGL 0xcf
> +#define RK816_RELAX_CUR2_REGH 0xd0
> +#define RK816_RELAX_CUR2_REGL 0xd1
> +#define RK816_CAL_OFFSET_REGH 0xd2
> +#define RK816_CAL_OFFSET_REGL 0xd3
> +#define RK816_NON_ACT_TIMER_CNT_REG 0xd4
> +#define RK816_VCALIB0_REGH 0xd5
> +#define RK816_VCALIB0_REGL 0xd6
> +#define RK816_VCALIB1_REGH 0xd7
> +#define RK816_VCALIB1_REGL 0xd8
> +#define RK816_FCC_GASCNT_REG(x) (0xdc - (x))
> +#define RK816_IOFFSET_REGH 0xdd
> +#define RK816_IOFFSET_REGL 0xde
> +#define RK816_SLEEP_CON_SAMP_CUR_REG 0xdf
> +
> +/* general purpose data registers 0xe0 ~ 0xf2 */
> +#define RK816_DATA_REG(x) (0xe0 + (x))
> +
> /* RK818 */
> #define RK818_DCDC1 0
> #define RK818_LDO1 4
> @@ -791,6 +930,7 @@ enum rk806_dvs_mode {
> #define VOUT_LO_INT BIT(0)
> #define CLK32KOUT2_EN BIT(0)
>
> +#define TEMP105C 0x08
> #define TEMP115C 0x0c
> #define TEMP_HOTDIE_MSK 0x0c
> #define SLP_SD_MSK (0x3 << 2)
> @@ -1191,6 +1331,7 @@ enum {
> RK806_ID = 0x8060,
> RK808_ID = 0x0000,
> RK809_ID = 0x8090,
> + RK816_ID = 0x8160,
> RK817_ID = 0x8170,
> RK818_ID = 0x8180,
> };
> --
> 2.43.2
>
--
Lee Jones [李琼斯]