This patch series introduces thermal sensor declaration to the Meson A1
common dtsi file. It also sets up thermal zones for the AD402 reference
board. It depends on the series with A1 thermal support at [1].
Links:
[1] - https://lore.kernel.org/all/[email protected]/
Dmitry Rokosov (3):
arm64: dts: amlogic: a1: add cooling-cells for DVFS feature
arm64: dts: amlogic: a1: introduce cpu temperature sensor
arm64: dts: amlogic: ad402: setup thermal-zones
.../arm64/boot/dts/amlogic/meson-a1-ad402.dts | 45 +++++++++++++++++++
arch/arm64/boot/dts/amlogic/meson-a1.dtsi | 14 ++++++
2 files changed, 59 insertions(+)
--
2.43.0
There is one thermal zone with 3 trip points: soc_passive, soc_hot, and
soc_critical, as well as two cooling maps.
Signed-off-by: Dmitry Rokosov <[email protected]>
---
.../arm64/boot/dts/amlogic/meson-a1-ad402.dts | 45 +++++++++++++++++++
1 file changed, 45 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-a1-ad402.dts b/arch/arm64/boot/dts/amlogic/meson-a1-ad402.dts
index 6c02301840ff..2d22e8b45c6d 100644
--- a/arch/arm64/boot/dts/amlogic/meson-a1-ad402.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-a1-ad402.dts
@@ -7,6 +7,7 @@
/dts-v1/;
#include "meson-a1.dtsi"
+#include <dt-bindings/thermal/thermal.h>
#include <dt-bindings/gpio/gpio.h>
@@ -177,6 +178,50 @@ codec {
};
};
};
+
+ thermal-zones {
+ soc_thermal: soc_thermal {
+ polling-delay = <1000>;
+ polling-delay-passive = <100>;
+ sustainable-power = <130>;
+
+ thermal-sensors = <&cpu_temp>;
+
+ trips {
+ soc_passive: soc-passive {
+ temperature = <70000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ soc_hot: soc-hot {
+ temperature = <85000>;
+ hysteresis = <5000>;
+ type = "hot";
+ };
+
+ soc_critical: soc-critical {
+ temperature = <110000>;
+ hysteresis = <1000>;
+ type = "critical";
+ };
+ };
+
+ soc_cooling_maps: cooling-maps {
+ map0 {
+ trip = <&soc_passive>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+
+ map1 {
+ trip = <&soc_hot>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
};
/* Bluetooth HCI H4 */
--
2.43.0
It's used for CPU with DVFS feature to specify minimum and maximum
cooling state used in the reference.
Without these values DVFS will not work and dtbs_check will raise the
error.
Signed-off-by: Dmitry Rokosov <[email protected]>
---
arch/arm64/boot/dts/amlogic/meson-a1.dtsi | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-a1.dtsi b/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
index fbee986421f1..f65d4a77ee52 100644
--- a/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
@@ -32,6 +32,7 @@ cpu0: cpu@0 {
reg = <0x0 0x0>;
enable-method = "psci";
next-level-cache = <&l2>;
+ #cooling-cells = <2>;
};
cpu1: cpu@1 {
@@ -40,6 +41,7 @@ cpu1: cpu@1 {
reg = <0x0 0x1>;
enable-method = "psci";
next-level-cache = <&l2>;
+ #cooling-cells = <2>;
};
l2: l2-cache0 {
--
2.43.0
On 28/03/2024 14:44, Dmitry Rokosov wrote:
> It's used for CPU with DVFS feature to specify minimum and maximum
> cooling state used in the reference.
> Without these values DVFS will not work and dtbs_check will raise the
> error.
>
> Signed-off-by: Dmitry Rokosov <[email protected]>
> ---
> arch/arm64/boot/dts/amlogic/meson-a1.dtsi | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-a1.dtsi b/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
> index fbee986421f1..f65d4a77ee52 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
> @@ -32,6 +32,7 @@ cpu0: cpu@0 {
> reg = <0x0 0x0>;
> enable-method = "psci";
> next-level-cache = <&l2>;
> + #cooling-cells = <2>;
> };
>
> cpu1: cpu@1 {
> @@ -40,6 +41,7 @@ cpu1: cpu@1 {
> reg = <0x0 0x1>;
> enable-method = "psci";
> next-level-cache = <&l2>;
> + #cooling-cells = <2>;
> };
>
> l2: l2-cache0 {
Reviewed-by: Neil Armstrong <[email protected]>