From: Jacky Huang <[email protected]>
This patch series adds the pin control and GPIO driver for the nuvoton ma35d1
ARMv8 SoC. It includes DT binding documentation and the ma35d1 pin control driver.
This pin control driver has been tested on the ma35d1 som board with Linux 6.9.0.
v7:
- Replace the magic numbers appearing in the driver with defined constants, or
provide comments to explain them.
- Update the ma35_irq_irqtype()
- irq_set_handler_locked(d, handle_edge_irq) and
irq_set_handler_locked(d, handle_level_irq)
- add case IRQ_TYPE_EDGE_BOTH
- Use handle_bad_irq for girq->handler, instead of handle_level_irq
v6:
- Remove DTS from this patchset. The DTS will be submitted in another patchset.
v5:
- Update the pinctrl driver header file pinctrl-ma35.h
- Include platform_device.h to fix compile issues.
v4:
- Update the pinctrl driver Kconfig
- Add depends to CONFIG_PINCTRL_MA35D1 to prevent compilation errors.
- Update the pinctrl driver
- Utilize devm_kcalloc() instead of devm_kzalloc().
- Employ ARRAY_SIZE() instead of sizeof()/sizeof().
v3:
- Update DTS and YAML files
- Corrected the unit address of nodes gpioa ~ gpion.
- Removed the invalid "pin-default" node.
- Removed the phandle entry from "nuvoton,pins".
- Update pinctrl driver
- Fixed the Kconfig by using "depend on" instead of "if".
- Removed unused #include of header files.
- Utilized immutable irq_chip instead of dynamic irq_chip.
- Replaced ma35_dt_free_map() with pinconf_generic_dt_free_map().
- Implemented other minor fixes as suggested by the reviewer.
v2:
- Update nuvoton,ma35d1-pinctrl.yaml
- Update the 'nuvoton,pins' to follow the style of rockchip pinctrl approch.
- Use power-source to indicate the pin voltage selection which follow the
realtek pinctrl approch.
- Instead of integer, use drive-strength-microamp to specify the real driving
strength capability of IO pins.
- Update ma35d1 pinctrl driver
- Add I/O drive strength lookup table for translating device tree setting
into control register.
- Remove ma35d1-pinfunc.h which is unused after update definition of 'nuvoton,pins'.
Jacky Huang (3):
dt-bindings: reset: Add syscon to nuvoton ma35d1 system-management
node
dt-bindings: pinctrl: Document nuvoton ma35d1 pin control
pinctrl: nuvoton: Add ma35d1 pinctrl and GPIO driver
.../pinctrl/nuvoton,ma35d1-pinctrl.yaml | 163 ++
.../bindings/reset/nuvoton,ma35d1-reset.yaml | 3 +-
drivers/pinctrl/nuvoton/Kconfig | 19 +
drivers/pinctrl/nuvoton/Makefile | 2 +
drivers/pinctrl/nuvoton/pinctrl-ma35.c | 1233 +++++++++++
drivers/pinctrl/nuvoton/pinctrl-ma35.h | 51 +
drivers/pinctrl/nuvoton/pinctrl-ma35d1.c | 1797 +++++++++++++++++
7 files changed, 3267 insertions(+), 1 deletion(-)
create mode 100644 Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35.c
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35.h
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35d1.c
--
2.34.1
From: Jacky Huang <[email protected]>
Add a compatible 'syscon' to the system management node since the system
control registers are mapped by this driver. The other driver must access
the system control registers through 'regmap' using a phandle that
references this node.
Signed-off-by: Jacky Huang <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Acked-by: Philipp Zabel <[email protected]>
---
.../devicetree/bindings/reset/nuvoton,ma35d1-reset.yaml | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/reset/nuvoton,ma35d1-reset.yaml b/Documentation/devicetree/bindings/reset/nuvoton,ma35d1-reset.yaml
index 34c5c1c08ec1..3ce7dcecd87a 100644
--- a/Documentation/devicetree/bindings/reset/nuvoton,ma35d1-reset.yaml
+++ b/Documentation/devicetree/bindings/reset/nuvoton,ma35d1-reset.yaml
@@ -18,6 +18,7 @@ properties:
compatible:
items:
- const: nuvoton,ma35d1-reset
+ - const: syscon
reg:
maxItems: 1
@@ -37,7 +38,7 @@ examples:
- |
system-management@40460000 {
- compatible = "nuvoton,ma35d1-reset";
+ compatible = "nuvoton,ma35d1-reset", "syscon";
reg = <0x40460000 0x200>;
#reset-cells = <1>;
};
--
2.34.1
From: Jacky Huang <[email protected]>
Add documentation to describe nuvoton ma35d1 pin control and GPIO.
Signed-off-by: Jacky Huang <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
---
.../pinctrl/nuvoton,ma35d1-pinctrl.yaml | 163 ++++++++++++++++++
1 file changed, 163 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
new file mode 100644
index 000000000000..8b9ec263213f
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
@@ -0,0 +1,163 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/nuvoton,ma35d1-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Nuvoton MA35D1 pin control and GPIO
+
+maintainers:
+ - Shan-Chun Hung <[email protected]>
+ - Jacky Huang <[email protected]>
+
+allOf:
+ - $ref: pinctrl.yaml#
+
+properties:
+ compatible:
+ enum:
+ - nuvoton,ma35d1-pinctrl
+
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 1
+
+ nuvoton,sys:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ phandle of the system-management node.
+
+ ranges: true
+
+patternProperties:
+ "^gpio@[0-9a-f]+$":
+ type: object
+ additionalProperties: false
+ properties:
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 2
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 2
+
+ interrupts:
+ description:
+ The interrupt outputs to sysirq.
+ maxItems: 1
+
+ required:
+ - gpio-controller
+ - '#gpio-cells'
+ - reg
+ - clocks
+ - interrupt-controller
+ - '#interrupt-cells'
+ - interrupts
+
+ "^pin-[a-z0-9]+$":
+ type: object
+ description:
+ A pinctrl node should contain at least one subnodes representing the
+ pinctrl groups available on the machine. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to muxer
+ configuration, pullups, drive strength, input enable/disable and input
+ schmitt.
+
+ $ref: pincfg-node.yaml#
+
+ properties:
+ power-source:
+ description: |
+ Valid arguments are described as below:
+ 0: power supply of 1.8V
+ 1: power supply of 3.3V
+ enum: [0, 1]
+
+ drive-strength-microamp:
+ oneOf:
+ - enum: [ 2900, 4400, 5800, 7300, 8600, 10100, 11500, 13000 ]
+ description: 1.8V I/O driving strength
+ - enum: [ 17100, 25600, 34100, 42800, 48000, 56000, 77000, 82000 ]
+ description: 3.3V I/O driving strength
+
+ unevaluatedProperties: false
+
+ "-grp$":
+ type: object
+ description:
+ Pinctrl node's client devices use subnodes for desired pin configuration.
+ Client device subnodes use below standard properties.
+ properties:
+ nuvoton,pins:
+ description:
+ Each entry consists of 4 parameters and represents the mux and config
+ setting for one pin.
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ minItems: 1
+ items:
+ items:
+ - minimum: 0
+ maximum: 13
+ description:
+ Pin bank.
+ - minimum: 0
+ maximum: 15
+ description:
+ Pin bank index.
+ - minimum: 0
+ maximum: 15
+ description:
+ Mux 0 means GPIO and mux 1 to 15 means the specific device function.
+
+required:
+ - compatible
+ - nuvoton,sys
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/clock/nuvoton,ma35d1-clk.h>
+
+ pinctrl@40040000 {
+ compatible = "nuvoton,ma35d1-pinctrl";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ nuvoton,sys = <&sys>;
+ ranges = <0 0x40040000 0xc00>;
+
+ gpio@0 {
+ reg = <0x0 0x40>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk GPA_GATE>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ uart-grp {
+ uart11-pins {
+ nuvoton,pins = <11 0 2>,
+ <11 1 2>,
+ <11 2 2>,
+ <11 3 2>;
+ bias-disable;
+ power-source = <1>;
+ };
+ };
+ };
--
2.34.1
From: Jacky Huang <[email protected]>
Add common pinctrl and GPIO driver for Nuvoton MA35 series SoC, and
add support for ma35d1 pinctrl.
Signed-off-by: Jacky Huang <[email protected]>
---
drivers/pinctrl/nuvoton/Kconfig | 19 +
drivers/pinctrl/nuvoton/Makefile | 2 +
drivers/pinctrl/nuvoton/pinctrl-ma35.c | 1233 +++++++++++++++
drivers/pinctrl/nuvoton/pinctrl-ma35.h | 51 +
drivers/pinctrl/nuvoton/pinctrl-ma35d1.c | 1797 ++++++++++++++++++++++
5 files changed, 3102 insertions(+)
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35.c
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35.h
create mode 100644 drivers/pinctrl/nuvoton/pinctrl-ma35d1.c
diff --git a/drivers/pinctrl/nuvoton/Kconfig b/drivers/pinctrl/nuvoton/Kconfig
index 2abbfcec1fae..7eadaaf48d6e 100644
--- a/drivers/pinctrl/nuvoton/Kconfig
+++ b/drivers/pinctrl/nuvoton/Kconfig
@@ -45,3 +45,22 @@ config PINCTRL_NPCM8XX
Say Y or M here to enable pin controller and GPIO support for
the Nuvoton NPCM8XX SoC. This is strongly recommended when
building a kernel that will run on this chip.
+
+config PINCTRL_MA35
+ bool
+ depends on (ARCH_MA35 || COMPILE_TEST) && OF
+ select GENERIC_PINCTRL_GROUPS
+ select GENERIC_PINMUX_FUNCTIONS
+ select GENERIC_PINCONF
+ select GPIOLIB
+ select GPIO_GENERIC
+ select GPIOLIB_IRQCHIP
+ select MFD_SYSCON
+
+config PINCTRL_MA35D1
+ bool "Pinctrl and GPIO driver for Nuvoton MA35D1"
+ depends on (ARCH_MA35 || COMPILE_TEST) && OF
+ select PINCTRL_MA35
+ help
+ Say Y here to enable pin controller and GPIO support
+ for Nuvoton MA35D1 SoC.
diff --git a/drivers/pinctrl/nuvoton/Makefile b/drivers/pinctrl/nuvoton/Makefile
index 08031eab0af6..346c5082bc60 100644
--- a/drivers/pinctrl/nuvoton/Makefile
+++ b/drivers/pinctrl/nuvoton/Makefile
@@ -4,3 +4,5 @@
obj-$(CONFIG_PINCTRL_WPCM450) += pinctrl-wpcm450.o
obj-$(CONFIG_PINCTRL_NPCM7XX) += pinctrl-npcm7xx.o
obj-$(CONFIG_PINCTRL_NPCM8XX) += pinctrl-npcm8xx.o
+obj-$(CONFIG_PINCTRL_MA35) += pinctrl-ma35.o
+obj-$(CONFIG_PINCTRL_MA35D1) += pinctrl-ma35d1.o
diff --git a/drivers/pinctrl/nuvoton/pinctrl-ma35.c b/drivers/pinctrl/nuvoton/pinctrl-ma35.c
new file mode 100644
index 000000000000..149d802c0c62
--- /dev/null
+++ b/drivers/pinctrl/nuvoton/pinctrl-ma35.c
@@ -0,0 +1,1233 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2023 Nuvoton Technology Corp.
+ *
+ * Author: Shan-Chun Hung <[email protected]>
+ */
+
+#include <linux/clk.h>
+#include <linux/gpio/driver.h>
+#include <linux/mfd/syscon.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_device.h>
+#include <linux/of_address.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include "../core.h"
+#include "../pinconf.h"
+#include "pinctrl-ma35.h"
+
+#define MA35_MFP_REG_BASE 0x80
+#define MA35_MFP_REG_SZ_PER_BANK 8
+#define MA35_MFP_BITS_PER_PORT 4
+
+#define MA35_GPIO_BANK_MAX 14
+#define MA35_GPIO_PORT_MAX 16
+
+/* GPIO control registers */
+#define MA35_GP_REG_MODE 0x00
+#define MA35_GP_REG_DINOFF 0x04
+#define MA35_GP_REG_DOUT 0x08
+#define MA35_GP_REG_DATMSK 0x0c
+#define MA35_GP_REG_PIN 0x10
+#define MA35_GP_REG_DBEN 0x14
+#define MA35_GP_REG_INTTYPE 0x18
+#define MA35_GP_REG_INTEN 0x1c
+#define MA35_GP_REG_INTSRC 0x20
+#define MA35_GP_REG_SMTEN 0x24
+#define MA35_GP_REG_SLEWCTL 0x28
+#define MA35_GP_REG_SPW 0x2c
+#define MA35_GP_REG_PUSEL 0x30
+#define MA35_GP_REG_DSL 0x38
+#define MA35_GP_REG_DSH 0x3c
+
+/* GPIO mode control */
+#define MA35_GP_MODE_INPUT 0x0
+#define MA35_GP_MODE_OUTPUT 0x1
+#define MA35_GP_MODE_OPEN_DRAIN 0x2
+#define MA35_GP_MODE_QUASI 0x3
+#define MA35_GP_MODE_MASK_WIDTH 2
+
+#define MA35_GP_SLEWCTL_MASK_WIDTH 2
+
+/* GPIO pull-up and pull-down selection control */
+#define MA35_GP_PUSEL_DISABLE 0x0
+#define MA35_GP_PUSEL_PULL_UP 0x1
+#define MA35_GP_PUSEL_PULL_DOWN 0x2
+#define MA35_GP_PUSEL_MASK_WIDTH 2
+
+/* Each pin data input/output is mapped by address mapping */
+#define MA35_PIN_MAP_BASE 0x800
+#define MA35_GP_DSH_BASE_PORT 8
+
+#define MVOLT_1800 0
+#define MVOLT_3300 1
+
+static const char * const gpio_group_name[] = {
+ "gpioa", "gpiob", "gpioc", "gpiod", "gpioe", "gpiof", "gpiog",
+ "gpioh", "gpioi", "gpioj", "gpiok", "gpiol", "gpiom", "gpion",
+};
+
+static const u32 ds_1800mv_tbl[] = {
+ 2900, 4400, 5800, 7300, 8600, 10100, 11500, 13000,
+};
+
+static const u32 ds_3300mv_tbl[] = {
+ 17100, 25600, 34100, 42800, 48000, 56000, 77000, 82000,
+};
+
+struct ma35_pin_func {
+ const char *name;
+ const char **groups;
+ u32 ngroups;
+};
+
+struct ma35_pin_setting {
+ u32 offset;
+ u32 shift;
+ u32 muxval;
+ unsigned long *configs;
+ unsigned int nconfigs;
+};
+
+struct ma35_pin_group {
+ const char *name;
+ unsigned int npins;
+ unsigned int *pins;
+ struct ma35_pin_setting *settings;
+};
+
+struct ma35_pin_bank {
+ void __iomem *reg_base;
+ struct clk *clk;
+ int irq;
+ u8 nr_pins;
+ const char *name;
+ u8 bank_num;
+ bool valid;
+ struct device_node *np;
+ struct gpio_chip chip;
+ u32 irqtype;
+ u32 irqinten;
+ struct regmap *regmap;
+ struct device *dev;
+ spinlock_t lock;
+};
+
+struct ma35_pin_ctrl {
+ struct ma35_pin_bank *pin_banks;
+ u32 nr_banks;
+ u32 nr_pins;
+};
+
+struct ma35_pinctrl {
+ struct device *dev;
+ struct ma35_pin_ctrl *ctrl;
+ struct pinctrl_dev *pctl;
+ const struct ma35_pinctrl_soc_info *info;
+ struct regmap *regmap;
+ struct ma35_pin_group *groups;
+ unsigned int ngroups;
+ struct ma35_pin_func *functions;
+ unsigned int nfunctions;
+};
+
+static int ma35_get_groups_count(struct pinctrl_dev *pctldev)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ return npctl->ngroups;
+}
+
+static const char *ma35_get_group_name(struct pinctrl_dev *pctldev, unsigned int selector)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ return npctl->groups[selector].name;
+}
+
+static int ma35_get_group_pins(struct pinctrl_dev *pctldev, unsigned int selector,
+ const unsigned int **pins, unsigned int *npins)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ if (selector >= npctl->ngroups)
+ return -EINVAL;
+
+ *pins = npctl->groups[selector].pins;
+ *npins = npctl->groups[selector].npins;
+
+ return 0;
+}
+
+static struct ma35_pin_group *ma35_pinctrl_find_group_by_name(
+ const struct ma35_pinctrl *npctl, const char *name)
+{
+ int i;
+
+ for (i = 0; i < npctl->ngroups; i++) {
+ if (!strcmp(npctl->groups[i].name, name))
+ return &npctl->groups[i];
+ }
+ return NULL;
+}
+
+static int ma35_pinctrl_dt_node_to_map_func(struct pinctrl_dev *pctldev,
+ struct device_node *np,
+ struct pinctrl_map **map,
+ unsigned int *num_maps)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+ struct ma35_pin_group *grp;
+ struct pinctrl_map *new_map;
+ struct device_node *parent;
+ int map_num = 1;
+ int i;
+
+ /*
+ * first find the group of this node and check if we need create
+ * config maps for pins
+ */
+ grp = ma35_pinctrl_find_group_by_name(npctl, np->name);
+ if (!grp) {
+ dev_err(npctl->dev, "unable to find group for node %s\n", np->name);
+ return -EINVAL;
+ }
+
+ map_num += grp->npins;
+ new_map = devm_kcalloc(pctldev->dev, map_num, sizeof(*new_map), GFP_KERNEL);
+ if (!new_map)
+ return -ENOMEM;
+
+ *map = new_map;
+ *num_maps = map_num;
+ /* create mux map */
+ parent = of_get_parent(np);
+ if (!parent) {
+ devm_kfree(pctldev->dev, new_map);
+ return -EINVAL;
+ }
+
+ new_map[0].type = PIN_MAP_TYPE_MUX_GROUP;
+ new_map[0].data.mux.function = parent->name;
+ new_map[0].data.mux.group = np->name;
+ of_node_put(parent);
+
+ new_map++;
+ for (i = 0; i < grp->npins; i++) {
+ new_map[i].type = PIN_MAP_TYPE_CONFIGS_PIN;
+ new_map[i].data.configs.group_or_pin = pin_get_name(pctldev, grp->pins[i]);
+ new_map[i].data.configs.configs = grp->settings[i].configs;
+ new_map[i].data.configs.num_configs = grp->settings[i].nconfigs;
+ }
+ dev_dbg(pctldev->dev, "maps: function %s group %s num %d\n",
+ (*map)->data.mux.function, (*map)->data.mux.group, map_num);
+
+ return 0;
+}
+
+static const struct pinctrl_ops ma35_pctrl_ops = {
+ .get_groups_count = ma35_get_groups_count,
+ .get_group_name = ma35_get_group_name,
+ .get_group_pins = ma35_get_group_pins,
+ .dt_node_to_map = ma35_pinctrl_dt_node_to_map_func,
+ .dt_free_map = pinconf_generic_dt_free_map,
+};
+
+static int ma35_pinmux_get_func_count(struct pinctrl_dev *pctldev)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ return npctl->nfunctions;
+}
+
+static const char *ma35_pinmux_get_func_name(struct pinctrl_dev *pctldev,
+ unsigned int selector)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ return npctl->functions[selector].name;
+}
+
+static int ma35_pinmux_get_func_groups(struct pinctrl_dev *pctldev,
+ unsigned int function,
+ const char *const **groups,
+ unsigned int *const num_groups)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+
+ *groups = npctl->functions[function].groups;
+ *num_groups = npctl->functions[function].ngroups;
+
+ return 0;
+}
+
+static int ma35_pinmux_set_mux(struct pinctrl_dev *pctldev, unsigned int selector,
+ unsigned int group)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+ struct ma35_pin_group *grp = &npctl->groups[group];
+ struct ma35_pin_setting *setting = grp->settings;
+ u32 i, regval;
+
+ dev_dbg(npctl->dev, "enable function %s group %s\n",
+ npctl->functions[selector].name, npctl->groups[group].name);
+
+ for (i = 0; i < grp->npins; i++) {
+ regmap_read(npctl->regmap, setting->offset, ®val);
+ regval &= ~GENMASK(setting->shift + MA35_MFP_BITS_PER_PORT - 1,
+ setting->shift);
+ regval |= setting->muxval << setting->shift;
+ regmap_write(npctl->regmap, setting->offset, regval);
+ setting++;
+ }
+ return 0;
+}
+
+static const struct pinmux_ops ma35_pmx_ops = {
+ .get_functions_count = ma35_pinmux_get_func_count,
+ .get_function_name = ma35_pinmux_get_func_name,
+ .get_function_groups = ma35_pinmux_get_func_groups,
+ .set_mux = ma35_pinmux_set_mux,
+ .strict = true,
+};
+
+static void ma35_gpio_set_mode(void __iomem *reg_mode, unsigned int gpio, u32 mode)
+{
+ u32 regval = readl(reg_mode);
+
+ regval &= ~GENMASK(gpio * MA35_GP_MODE_MASK_WIDTH - 1,
+ gpio * MA35_GP_MODE_MASK_WIDTH);
+ regval |= mode << gpio * MA35_GP_MODE_MASK_WIDTH;
+
+ writel(regval, reg_mode);
+}
+
+static u32 ma35_gpio_get_mode(void __iomem *reg_mode, unsigned int gpio)
+{
+ u32 regval = readl(reg_mode);
+
+ regval &= GENMASK(gpio * MA35_GP_MODE_MASK_WIDTH - 1,
+ gpio * MA35_GP_MODE_MASK_WIDTH);
+
+ return regval >> gpio * MA35_GP_MODE_MASK_WIDTH;
+}
+
+static int ma35_gpio_core_direction_in(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(gc);
+ void __iomem *reg_mode = bank->reg_base + MA35_GP_REG_MODE;
+ unsigned long flags;
+
+ spin_lock_irqsave(&bank->lock, flags);
+
+ ma35_gpio_set_mode(reg_mode, gpio, MA35_GP_MODE_INPUT);
+
+ spin_unlock_irqrestore(&bank->lock, flags);
+
+ return 0;
+}
+
+static int ma35_gpio_core_direction_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(gc);
+ void __iomem *reg_dout = bank->reg_base + MA35_GP_REG_DOUT;
+ void __iomem *reg_mode = bank->reg_base + MA35_GP_REG_MODE;
+ unsigned long flags;
+ unsigned int regval;
+
+ spin_lock_irqsave(&bank->lock, flags);
+
+ regval = readl(reg_dout);
+ if (val)
+ writel(regval | BIT(gpio), reg_dout);
+ else
+ writel(regval & ~BIT(gpio), reg_dout);
+
+ ma35_gpio_set_mode(reg_mode, gpio, MA35_GP_MODE_OUTPUT);
+
+ spin_unlock_irqrestore(&bank->lock, flags);
+
+ return 0;
+}
+
+static int ma35_gpio_core_get(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(gc);
+
+ /* The MA35 PIN_MAP maps each GPIO pin to an independent 32-bit register. */
+ return readl(bank->reg_base + MA35_PIN_MAP_BASE + gpio * 4);
+}
+
+static void ma35_gpio_core_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(gc);
+
+ writel(val, bank->reg_base + MA35_PIN_MAP_BASE + gpio * 4);
+}
+
+static int ma35_gpio_core_to_request(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(gc);
+ u32 reg_offs, bit_offs, regval;
+
+ if (gpio < 8) {
+ /* The MFP low register controls port 0 ~ 7 */
+ reg_offs = bank->bank_num * MA35_MFP_REG_SZ_PER_BANK;
+ bit_offs = gpio * MA35_MFP_BITS_PER_PORT;
+ } else {
+ /* The MFP high register controls port 8 ~ 15 */
+ reg_offs = bank->bank_num * MA35_MFP_REG_SZ_PER_BANK + 4;
+ bit_offs = (gpio - 8) * MA35_MFP_BITS_PER_PORT;
+ }
+
+ regmap_read(bank->regmap, MA35_MFP_REG_BASE + reg_offs, ®val);
+ regval &= ~GENMASK(bit_offs + MA35_MFP_BITS_PER_PORT - 1, bit_offs);
+ regmap_write(bank->regmap, MA35_MFP_REG_BASE + reg_offs, regval);
+
+ return 0;
+}
+
+static void ma35_irq_gpio_ack(struct irq_data *d)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(irq_data_get_irq_chip_data(d));
+ void __iomem *reg_intsrc = bank->reg_base + MA35_GP_REG_INTSRC;
+ unsigned int num = (d->hwirq);
+
+ writel(1<<num, reg_intsrc);
+}
+
+static void ma35_irq_gpio_mask(struct irq_data *d)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(irq_data_get_irq_chip_data(d));
+ void __iomem *reg_ien = bank->reg_base + MA35_GP_REG_INTEN;
+ unsigned int num = (d->hwirq);
+ u32 regval;
+
+ regval = readl(reg_ien);
+
+ /*
+ * The MA35_GP_REG_INTEN bits 0 ~ 15 control low-level or falling edge trigger,
+ * while bits 16 ~ 31 control high-level or rising edge trigger.
+ * We disable both type of interrupt.
+ */
+ regval &= ~(BIT(num + 16) | BIT(num));
+
+ writel(regval, reg_ien);
+}
+
+static void ma35_irq_gpio_unmask(struct irq_data *d)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(irq_data_get_irq_chip_data(d));
+ void __iomem *reg_itype = bank->reg_base + MA35_GP_REG_INTTYPE;
+ void __iomem *reg_ien = bank->reg_base + MA35_GP_REG_INTEN;
+ unsigned int num = (d->hwirq);
+ u32 bval, regval;
+
+ bval = bank->irqtype & BIT(num);
+
+ regval = readl(reg_itype);
+ regval &= ~BIT(num);
+ writel(regval | bval, reg_itype);
+
+ bval = bank->irqinten & (BIT(num + 16) | BIT(num));
+
+ regval = readl(reg_ien);
+ regval &= ~(BIT(num + 16) | BIT(num));
+ writel(regval | bval, reg_ien);
+}
+
+static int ma35_irq_irqtype(struct irq_data *d, unsigned int type)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(irq_data_get_irq_chip_data(d));
+ unsigned int num = (d->hwirq);
+
+ switch (type) {
+ case IRQ_TYPE_EDGE_BOTH:
+ irq_set_handler_locked(d, handle_edge_irq);
+ bank->irqtype &= ~(0x1 << num);
+ bank->irqinten |= (0x1 << num);
+ bank->irqinten |= (0x1 << (num + 16));
+ break;
+ case IRQ_TYPE_EDGE_RISING:
+ irq_set_handler_locked(d, handle_edge_irq);
+ bank->irqtype &= ~(0x1 << num);
+ bank->irqinten |= (0x1 << (num + 16));
+ bank->irqinten &= ~(0x1 << num);
+ break;
+ case IRQ_TYPE_EDGE_FALLING:
+ irq_set_handler_locked(d, handle_edge_irq);
+ bank->irqtype &= ~(0x1 << num);
+ bank->irqinten |= (0x1 << num);
+ bank->irqinten &= ~(0x1 << (num + 16));
+ break;
+ case IRQ_TYPE_LEVEL_HIGH:
+ irq_set_handler_locked(d, handle_level_irq);
+ bank->irqtype |= (0x1 << num);
+ bank->irqinten &= ~(0x1 << num);
+ bank->irqinten |= (0x1 << (num + 16));
+ break;
+ case IRQ_TYPE_LEVEL_LOW:
+ irq_set_handler_locked(d, handle_level_irq);
+ bank->irqtype |= (0x1 << num);
+ bank->irqinten &= ~(0x1 << (num + 16));
+ bank->irqinten |= (0x1 << num);
+ break;
+ default:
+ irq_set_handler_locked(d, handle_bad_irq);
+ return -EINVAL;
+ }
+
+ writel(bank->irqtype, bank->reg_base + MA35_GP_REG_INTTYPE);
+ writel(bank->irqinten, bank->reg_base + MA35_GP_REG_INTEN);
+
+ return 0;
+}
+
+static struct irq_chip ma35_gpio_irqchip = {
+ .name = "MA35-GPIO-IRQ",
+ .irq_disable = ma35_irq_gpio_mask,
+ .irq_enable = ma35_irq_gpio_unmask,
+ .irq_ack = ma35_irq_gpio_ack,
+ .irq_mask = ma35_irq_gpio_mask,
+ .irq_unmask = ma35_irq_gpio_unmask,
+ .irq_set_type = ma35_irq_irqtype,
+ .flags = IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_SKIP_SET_WAKE | IRQCHIP_IMMUTABLE,
+};
+
+static void ma35_irq_demux_intgroup(struct irq_desc *desc)
+{
+ struct ma35_pin_bank *bank = gpiochip_get_data(irq_desc_get_handler_data(desc));
+ struct irq_domain *irqdomain = bank->chip.irq.domain;
+ struct irq_chip *irqchip = irq_desc_get_chip(desc);
+ unsigned long isr;
+ int offset;
+
+ chained_irq_enter(irqchip, desc);
+
+ isr = readl(bank->reg_base + MA35_GP_REG_INTSRC);
+
+ if (isr)
+ for_each_set_bit(offset, &isr, bank->nr_pins)
+ generic_handle_irq(irq_find_mapping(irqdomain, offset));
+
+ chained_irq_exit(irqchip, desc);
+}
+
+static int ma35_gpiolib_register(struct platform_device *pdev, struct ma35_pinctrl *npctl)
+{
+ struct ma35_pin_ctrl *ctrl = npctl->ctrl;
+ struct ma35_pin_bank *bank = ctrl->pin_banks;
+ int ret;
+ int i;
+
+ for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
+ if (!bank->valid) {
+ dev_warn(&pdev->dev, "bank %s is not valid\n",
+ bank->np->name);
+ continue;
+ }
+ bank->irqtype = 0;
+ bank->irqinten = 0;
+ bank->chip.label = bank->name;
+ bank->chip.of_gpio_n_cells = 2;
+ bank->chip.parent = &pdev->dev;
+ bank->chip.request = ma35_gpio_core_to_request;
+ bank->chip.direction_input = ma35_gpio_core_direction_in;
+ bank->chip.direction_output = ma35_gpio_core_direction_out;
+ bank->chip.get = ma35_gpio_core_get;
+ bank->chip.set = ma35_gpio_core_set;
+ bank->chip.base = -1;
+ bank->chip.ngpio = bank->nr_pins;
+ bank->chip.can_sleep = false;
+ spin_lock_init(&bank->lock);
+
+ if (bank->irq > 0) {
+ struct gpio_irq_chip *girq;
+
+ girq = &bank->chip.irq;
+ gpio_irq_chip_set_chip(girq, &ma35_gpio_irqchip);
+ girq->parent_handler = ma35_irq_demux_intgroup;
+ girq->num_parents = 1;
+
+ girq->parents = devm_kcalloc(&pdev->dev, 1, sizeof(*girq->parents),
+ GFP_KERNEL);
+ if (!girq->parents) {
+ ret = -ENOMEM;
+ goto fail;
+ }
+
+ girq->parents[0] = bank->irq;
+ girq->default_type = IRQ_TYPE_NONE;
+ girq->handler = handle_bad_irq;
+ }
+
+ ret = gpiochip_add_data(&bank->chip, bank);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to register gpio_chip %s, error code: %d\n",
+ bank->chip.label, ret);
+ goto fail;
+ }
+ }
+ return 0;
+
+fail:
+ for (--i, --bank; i >= 0; --i, --bank) {
+ if (!bank->valid)
+ continue;
+ gpiochip_remove(&bank->chip);
+ }
+ return ret;
+}
+
+static int ma35_get_bank_data(struct ma35_pin_bank *bank, struct ma35_pinctrl *npctl)
+{
+ struct resource res;
+
+ if (of_address_to_resource(bank->np, 0, &res)) {
+ dev_err(npctl->dev, "cannot find IO resource for bank\n");
+ return -ENOENT;
+ }
+
+ bank->reg_base = devm_ioremap_resource(npctl->dev, &res);
+ if (IS_ERR(bank->reg_base)) {
+ dev_err(npctl->dev, "cannot ioremap resource for bank\n");
+ return PTR_ERR(bank->reg_base);
+ }
+
+ bank->irq = irq_of_parse_and_map(bank->np, 0);
+ bank->nr_pins = MA35_GPIO_PORT_MAX;
+
+ bank->clk = of_clk_get(bank->np, 0);
+ if (IS_ERR(bank->clk))
+ return PTR_ERR(bank->clk);
+
+ return clk_prepare_enable(bank->clk);
+}
+
+static int ma35_pinctrl_get_soc_data(struct ma35_pinctrl *pctl, struct platform_device *pdev)
+{
+ struct fwnode_handle *child;
+ struct ma35_pin_ctrl *ctrl;
+ struct ma35_pin_bank *bank;
+ int i, id = 0;
+
+ ctrl = pctl->ctrl;
+ ctrl->nr_banks = MA35_GPIO_BANK_MAX;
+
+ ctrl->pin_banks = devm_kcalloc(&pdev->dev, ctrl->nr_banks,
+ sizeof(*ctrl->pin_banks), GFP_KERNEL);
+ if (!ctrl->pin_banks)
+ return -ENOMEM;
+
+ for (i = 0; i < ctrl->nr_banks; i++) {
+ ctrl->pin_banks[i].bank_num = i;
+ ctrl->pin_banks[i].name = gpio_group_name[i];
+ }
+
+ for_each_gpiochip_node(&pdev->dev, child) {
+ struct device_node *np = to_of_node(child);
+
+ bank = &ctrl->pin_banks[id];
+ bank->np = np;
+ bank->regmap = pctl->regmap;
+ bank->dev = &pdev->dev;
+ if (!ma35_get_bank_data(bank, pctl))
+ bank->valid = true;
+ id++;
+ }
+ return 0;
+}
+
+static void ma35_gpio_cla_port(unsigned int gpio_num, unsigned int *group,
+ unsigned int *num)
+{
+ *group = gpio_num / MA35_GPIO_PORT_MAX;
+ *num = gpio_num % MA35_GPIO_PORT_MAX;
+}
+
+static int ma35_pinconf_set_pull(struct ma35_pinctrl *npctl, unsigned int pin,
+ int pull_up)
+{
+ unsigned int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_PUSEL);
+ regval &= ~GENMASK(port * MA35_GP_PUSEL_MASK_WIDTH - 1,
+ port * MA35_GP_PUSEL_MASK_WIDTH);
+
+ switch (pull_up) {
+ case PIN_CONFIG_BIAS_PULL_UP:
+ regval |= MA35_GP_PUSEL_PULL_UP << port * MA35_GP_PUSEL_MASK_WIDTH;
+ break;
+
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ regval |= MA35_GP_PUSEL_PULL_DOWN << port * MA35_GP_PUSEL_MASK_WIDTH;
+ break;
+
+ case MA35_GP_PUSEL_DISABLE:
+ regval |= MA35_GP_PUSEL_DISABLE << port * MA35_GP_PUSEL_MASK_WIDTH;
+ break;
+
+ default:
+ regval |= MA35_GP_PUSEL_DISABLE << port * MA35_GP_PUSEL_MASK_WIDTH;
+ break;
+ }
+ writel(regval, base + MA35_GP_REG_PUSEL);
+
+ return 0;
+}
+
+static int ma35_pinconf_get_output(struct ma35_pinctrl *npctl, unsigned int pin)
+{
+ unsigned int port, group_num;
+ void __iomem *base;
+ u32 mode;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ mode = ma35_gpio_get_mode(base + MA35_GP_REG_MODE, port);
+ if (mode == MA35_GP_MODE_OUTPUT)
+ return 1;
+
+ return 0;
+}
+
+static int ma35_pinconf_get_pull(struct ma35_pinctrl *npctl, unsigned int pin)
+{
+ unsigned int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_PUSEL);
+ regval &= GENMASK(port * MA35_GP_PUSEL_MASK_WIDTH - 1,
+ port * MA35_GP_PUSEL_MASK_WIDTH);
+ regval >>= port * MA35_GP_PUSEL_MASK_WIDTH;
+
+ switch (regval) {
+ case MA35_GP_PUSEL_PULL_UP:
+ return PIN_CONFIG_BIAS_PULL_UP;
+
+ case MA35_GP_PUSEL_PULL_DOWN:
+ return PIN_CONFIG_BIAS_PULL_DOWN;
+
+ case MA35_GP_PUSEL_DISABLE:
+ return PIN_CONFIG_BIAS_DISABLE;
+ }
+
+ return PIN_CONFIG_BIAS_DISABLE;
+}
+
+static int ma35_pinconf_set_output(struct ma35_pinctrl *npctl, unsigned int pin, bool out)
+{
+ unsigned int port, group_num;
+ void __iomem *base;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ ma35_gpio_set_mode(base + MA35_GP_REG_MODE, port, MA35_GP_MODE_OUTPUT);
+
+ return 0;
+}
+
+static int ma35_pinconf_get_power_source(struct ma35_pinctrl *npctl, unsigned int pin)
+{
+ unsigned int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SPW);
+
+ if (regval & BIT(port))
+ return MVOLT_3300;
+ else
+ return MVOLT_1800;
+}
+
+static int ma35_pinconf_set_power_source(struct ma35_pinctrl *npctl,
+ unsigned int pin, int arg)
+{
+ unsigned int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ if ((arg != MVOLT_1800) && (arg != MVOLT_3300))
+ return -EINVAL;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SPW);
+
+ if (arg == MVOLT_1800)
+ regval &= ~BIT(port);
+ else
+ regval |= BIT(port);
+
+ writel(regval, base + MA35_GP_REG_SPW);
+
+ return 0;
+}
+
+static int ma35_pinconf_get_drive_strength(struct ma35_pinctrl *npctl, unsigned int pin,
+ u32 *strength)
+{
+ unsigned int port, group_num;
+ void __iomem *base;
+ u32 regval, ds_val;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ /*
+ * The MA35_GP_REG_DSL register controls ports 0 to 7, while the MA35_GP_REG_DSH
+ * register controls ports 8 to 15. Each port occupies a width of 4 bits, with 3
+ * bits being effective.
+ */
+ if (port < MA35_GP_DSH_BASE_PORT) {
+ regval = readl(base + MA35_GP_REG_DSL);
+ ds_val = (regval & GENMASK(port * 4 + 2, port * 4)) >> port * 4;
+ } else {
+ port -= MA35_GP_DSH_BASE_PORT;
+ regval = readl(base + MA35_GP_REG_DSH);
+ ds_val = (regval & GENMASK(port * 4 + 2, port * 4)) >> port * 4;
+ }
+
+ if (ma35_pinconf_get_power_source(npctl, pin) == MVOLT_1800)
+ *strength = ds_1800mv_tbl[ds_val];
+ else
+ *strength = ds_3300mv_tbl[ds_val];
+
+ return 0;
+}
+
+static int ma35_pinconf_set_drive_strength(struct ma35_pinctrl *npctl, unsigned int pin,
+ int strength)
+{
+ unsigned int port, group_num;
+ void __iomem *base;
+ int i, ds_val = -1;
+ u32 regval;
+
+ if (ma35_pinconf_get_power_source(npctl, pin) == MVOLT_1800) {
+ for (i = 0; i < ARRAY_SIZE(ds_1800mv_tbl); i++) {
+ if (ds_1800mv_tbl[i] == strength)
+ ds_val = i;
+ }
+ } else {
+ for (i = 0; i < ARRAY_SIZE(ds_3300mv_tbl); i++) {
+ if (ds_3300mv_tbl[i] == strength)
+ ds_val = i;
+ }
+ }
+ if (ds_val == -1)
+ return -EINVAL;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ if (port < MA35_GP_DSH_BASE_PORT) {
+ regval = readl(base + MA35_GP_REG_DSL);
+ regval &= ~GENMASK(port * 4 + 2, port * 4);
+ regval |= ds_val << port * 4;
+ writel(regval, base + MA35_GP_REG_DSL);
+ } else {
+ port -= MA35_GP_DSH_BASE_PORT;
+ regval = readl(base + MA35_GP_REG_DSH);
+ regval &= ~GENMASK(port * 4 + 2, port * 4);
+ regval |= ds_val << port * 4;
+ writel(regval, base + MA35_GP_REG_DSH);
+ }
+ return 0;
+}
+
+static int ma35_pinconf_get_schmitt_enable(struct ma35_pinctrl *npctl, unsigned int pin)
+{
+ unsigned int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SMTEN);
+
+ return !!(regval & BIT(port));
+}
+
+static int ma35_pinconf_set_schmitt(struct ma35_pinctrl *npctl, unsigned int pin, int enable)
+{
+ unsigned int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SMTEN);
+
+ if (enable)
+ regval |= BIT(port);
+ else
+ regval &= ~BIT(port);
+
+ writel(regval, base + MA35_GP_REG_SMTEN);
+
+ return 0;
+}
+
+static int ma35_pinconf_get_slew_rate(struct ma35_pinctrl *npctl, unsigned int pin)
+{
+ unsigned int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SLEWCTL);
+ regval &= GENMASK(port * MA35_GP_SLEWCTL_MASK_WIDTH - 1,
+ port * MA35_GP_SLEWCTL_MASK_WIDTH);
+
+ return regval >> port * MA35_GP_SLEWCTL_MASK_WIDTH;
+}
+
+static int ma35_pinconf_set_slew_rate(struct ma35_pinctrl *npctl, unsigned int pin, int rate)
+{
+ unsigned int port, group_num;
+ void __iomem *base;
+ u32 regval;
+
+ ma35_gpio_cla_port(pin, &group_num, &port);
+ base = npctl->ctrl->pin_banks[group_num].reg_base;
+
+ regval = readl(base + MA35_GP_REG_SLEWCTL);
+ regval &= ~GENMASK(port * MA35_GP_SLEWCTL_MASK_WIDTH - 1,
+ port * MA35_GP_SLEWCTL_MASK_WIDTH);
+ regval |= rate << port * MA35_GP_SLEWCTL_MASK_WIDTH;
+ writel(regval, base + MA35_GP_REG_SLEWCTL);
+
+ return 0;
+}
+
+static int ma35_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin, unsigned long *config)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+ enum pin_config_param param = pinconf_to_config_param(*config);
+ u32 arg;
+ int ret;
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ case PIN_CONFIG_BIAS_PULL_UP:
+ if (ma35_pinconf_get_pull(npctl, pin) == param)
+ arg = 1;
+ else
+ return -EINVAL;
+ break;
+
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ ret = ma35_pinconf_get_drive_strength(npctl, pin, &arg);
+ if (ret)
+ return ret;
+ break;
+
+ case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+ arg = ma35_pinconf_get_schmitt_enable(npctl, pin);
+ break;
+
+ case PIN_CONFIG_SLEW_RATE:
+ arg = ma35_pinconf_get_slew_rate(npctl, pin);
+ break;
+
+ case PIN_CONFIG_OUTPUT_ENABLE:
+ arg = ma35_pinconf_get_output(npctl, pin);
+ break;
+
+ case PIN_CONFIG_POWER_SOURCE:
+ arg = ma35_pinconf_get_power_source(npctl, pin);
+ break;
+
+ default:
+ return -EINVAL;
+ }
+ *config = pinconf_to_config_packed(param, arg);
+
+ return 0;
+}
+
+static int ma35_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
+ unsigned long *configs, unsigned int num_configs)
+{
+ struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
+ enum pin_config_param param;
+ unsigned int arg = 0;
+ int i, ret = 0;
+
+ for (i = 0; i < num_configs; i++) {
+ param = pinconf_to_config_param(configs[i]);
+ arg = pinconf_to_config_argument(configs[i]);
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ case PIN_CONFIG_BIAS_PULL_UP:
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ ret = ma35_pinconf_set_pull(npctl, pin, param);
+ break;
+
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ ret = ma35_pinconf_set_drive_strength(npctl, pin, arg);
+ break;
+
+ case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+ ret = ma35_pinconf_set_schmitt(npctl, pin, 1);
+ break;
+
+ case PIN_CONFIG_INPUT_SCHMITT:
+ ret = ma35_pinconf_set_schmitt(npctl, pin, arg);
+ break;
+
+ case PIN_CONFIG_SLEW_RATE:
+ ret = ma35_pinconf_set_slew_rate(npctl, pin, arg);
+ break;
+
+ case PIN_CONFIG_OUTPUT_ENABLE:
+ ret = ma35_pinconf_set_output(npctl, pin, arg);
+ break;
+
+ case PIN_CONFIG_POWER_SOURCE:
+ ret = ma35_pinconf_set_power_source(npctl, pin, arg);
+ break;
+
+ default:
+ return -EINVAL;
+ }
+ }
+ return ret;
+}
+
+static const struct pinconf_ops ma35_pinconf_ops = {
+ .pin_config_get = ma35_pinconf_get,
+ .pin_config_set = ma35_pinconf_set,
+ .is_generic = true,
+};
+
+static int ma35_pinctrl_parse_groups(struct device_node *np, struct ma35_pin_group *grp,
+ struct ma35_pinctrl *npctl, u32 index)
+{
+ unsigned long *configs;
+ unsigned int nconfigs;
+ struct ma35_pin_setting *pin;
+ const __be32 *list;
+ int i, j, size, ret;
+
+ dev_dbg(npctl->dev, "group(%d): %s\n", index, np->name);
+
+ grp->name = np->name;
+
+ ret = pinconf_generic_parse_dt_config(np, NULL, &configs, &nconfigs);
+ if (ret)
+ return ret;
+
+ /*
+ * the binding format is nuvoton,pins = <bank pin-mfp pin-function>,
+ * do sanity check and calculate pins number
+ */
+ list = of_get_property(np, "nuvoton,pins", &size);
+ size /= sizeof(*list);
+ if (!size || size % 3) {
+ dev_err(npctl->dev, "wrong setting!\n");
+ return -EINVAL;
+ }
+ grp->npins = size / 3;
+
+ grp->pins = devm_kcalloc(npctl->dev, grp->npins, sizeof(*grp->pins), GFP_KERNEL);
+ if (!grp->pins)
+ return -ENOMEM;
+
+ grp->settings = devm_kcalloc(npctl->dev, grp->npins, sizeof(*grp->settings), GFP_KERNEL);
+ if (!grp->settings)
+ return -ENOMEM;
+
+ pin = grp->settings;
+
+ for (i = 0, j = 0; i < size; i += 3, j++) {
+ pin->offset = be32_to_cpu(*list++) * MA35_MFP_REG_SZ_PER_BANK + MA35_MFP_REG_BASE;
+ pin->shift = (be32_to_cpu(*list++) * MA35_MFP_BITS_PER_PORT) % 32;
+ pin->muxval = be32_to_cpu(*list++);
+ pin->configs = configs;
+ pin->nconfigs = nconfigs;
+ grp->pins[j] = npctl->info->get_pin_num(pin->offset, pin->shift);
+ pin++;
+ }
+ return 0;
+}
+
+static int ma35_pinctrl_parse_functions(struct device_node *np, struct ma35_pinctrl *npctl,
+ u32 index)
+{
+ struct device_node *child;
+ struct ma35_pin_func *func;
+ struct ma35_pin_group *grp;
+ static u32 grp_index;
+ u32 ret, i = 0;
+
+ dev_dbg(npctl->dev, "parse function(%d): %s\n", index, np->name);
+
+ func = &npctl->functions[index];
+ func->name = np->name;
+ func->ngroups = of_get_child_count(np);
+
+ if (func->ngroups <= 0)
+ return 0;
+
+ func->groups = devm_kcalloc(npctl->dev, func->ngroups, sizeof(char *), GFP_KERNEL);
+ if (!func->groups)
+ return -ENOMEM;
+
+ for_each_child_of_node(np, child) {
+ func->groups[i] = child->name;
+ grp = &npctl->groups[grp_index++];
+ ret = ma35_pinctrl_parse_groups(child, grp, npctl, i++);
+ if (ret) {
+ of_node_put(child);
+ return ret;
+ }
+ }
+ return 0;
+}
+
+static int ma35_pinctrl_probe_dt(struct platform_device *pdev, struct ma35_pinctrl *npctl)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct device_node *child;
+ u32 idx = 0;
+ int ret;
+
+ if (!np)
+ return -ENODEV;
+
+ for_each_child_of_node(np, child) {
+ if (of_property_read_bool(child, "gpio-controller"))
+ continue;
+ npctl->nfunctions++;
+ npctl->ngroups += of_get_child_count(child);
+ }
+
+ npctl->functions = devm_kcalloc(&pdev->dev, npctl->nfunctions,
+ sizeof(*npctl->functions), GFP_KERNEL);
+ if (!npctl->functions)
+ return -ENOMEM;
+
+ npctl->groups = devm_kcalloc(&pdev->dev, npctl->ngroups,
+ sizeof(*npctl->groups), GFP_KERNEL);
+ if (!npctl->groups)
+ return -ENOMEM;
+
+ dev_dbg(&pdev->dev, "nfunctions = %d\n", npctl->nfunctions);
+ dev_dbg(&pdev->dev, "ngroups = %d\n", npctl->ngroups);
+
+ for_each_child_of_node(np, child) {
+ if (of_property_read_bool(child, "gpio-controller"))
+ continue;
+
+ ret = ma35_pinctrl_parse_functions(child, npctl, idx++);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to parse function\n");
+ of_node_put(child);
+ return ret;
+ }
+ }
+ return 0;
+}
+
+int ma35_pinctrl_probe(struct platform_device *pdev, const struct ma35_pinctrl_soc_info *info)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct pinctrl_desc *ma35_pinctrl_desc;
+ struct ma35_pinctrl *npctl;
+ int ret;
+
+ if (!info || !info->pins || !info->npins) {
+ dev_err(&pdev->dev, "wrong pinctrl info\n");
+ return -EINVAL;
+ }
+
+ npctl = devm_kzalloc(&pdev->dev, sizeof(*npctl), GFP_KERNEL);
+ if (!npctl)
+ return -ENOMEM;
+
+ ma35_pinctrl_desc = devm_kzalloc(&pdev->dev, sizeof(*ma35_pinctrl_desc), GFP_KERNEL);
+ if (!ma35_pinctrl_desc)
+ return -ENOMEM;
+
+ npctl->ctrl = devm_kzalloc(&pdev->dev, sizeof(*npctl->ctrl), GFP_KERNEL);
+ if (!npctl->ctrl)
+ return -ENOMEM;
+
+ ma35_pinctrl_desc->name = dev_name(&pdev->dev);
+ ma35_pinctrl_desc->pins = info->pins;
+ ma35_pinctrl_desc->npins = info->npins;
+ ma35_pinctrl_desc->pctlops = &ma35_pctrl_ops;
+ ma35_pinctrl_desc->pmxops = &ma35_pmx_ops;
+ ma35_pinctrl_desc->confops = &ma35_pinconf_ops;
+ ma35_pinctrl_desc->owner = THIS_MODULE;
+
+ npctl->info = info;
+ npctl->dev = &pdev->dev;
+
+ npctl->regmap = syscon_regmap_lookup_by_phandle(np, "nuvoton,sys");
+ if (IS_ERR(npctl->regmap))
+ return dev_err_probe(&pdev->dev, PTR_ERR(npctl->regmap),
+ "No syscfg phandle specified\n");
+
+ ma35_pinctrl_get_soc_data(npctl, pdev);
+
+ platform_set_drvdata(pdev, npctl);
+
+ ret = ma35_pinctrl_probe_dt(pdev, npctl);
+ if (ret)
+ return dev_err_probe(&pdev->dev, ret, "fail to probe MA35 pinctrl dt\n");
+
+ ret = devm_pinctrl_register_and_init(&pdev->dev, ma35_pinctrl_desc,
+ npctl, &npctl->pctl);
+ if (ret)
+ return dev_err_probe(&pdev->dev, ret, "fail to register MA35 pinctrl\n");
+
+ ret = pinctrl_enable(npctl->pctl);
+ if (ret)
+ return dev_err_probe(&pdev->dev, ret, "fail to enable MA35 pinctrl\n");
+
+ return ma35_gpiolib_register(pdev, npctl);
+}
+
+int __maybe_unused ma35_pinctrl_suspend(struct device *dev)
+{
+ struct ma35_pinctrl *npctl = dev_get_drvdata(dev);
+
+ return pinctrl_force_sleep(npctl->pctl);
+}
+
+int __maybe_unused ma35_pinctrl_resume(struct device *dev)
+{
+ struct ma35_pinctrl *npctl = dev_get_drvdata(dev);
+
+ return pinctrl_force_default(npctl->pctl);
+}
diff --git a/drivers/pinctrl/nuvoton/pinctrl-ma35.h b/drivers/pinctrl/nuvoton/pinctrl-ma35.h
new file mode 100644
index 000000000000..281605e2c231
--- /dev/null
+++ b/drivers/pinctrl/nuvoton/pinctrl-ma35.h
@@ -0,0 +1,51 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2023 Nuvoton Technology Corp.
+ *
+ * Author: Shan-Chun Hung <[email protected]>
+ */
+#ifndef __PINCTRL_MA35_H
+#define __PINCTRL_MA35_H
+
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/platform_device.h>
+
+struct ma35_mux_desc {
+ const char *name;
+ u32 muxval;
+};
+
+struct ma35_pin_data {
+ u32 offset;
+ u32 shift;
+ struct ma35_mux_desc *muxes;
+};
+
+struct ma35_pinctrl_soc_info {
+ const struct pinctrl_pin_desc *pins;
+ unsigned int npins;
+ int (*get_pin_num)(int offset, int shift);
+};
+
+#define MA35_PIN(num, n, o, s, ...) { \
+ .number = num, \
+ .name = #n, \
+ .drv_data = &(struct ma35_pin_data) { \
+ .offset = o, \
+ .shift = s, \
+ .muxes = (struct ma35_mux_desc[]) { \
+ __VA_ARGS__, { } }, \
+ }, \
+}
+
+#define MA35_MUX(_val, _name) { \
+ .name = _name, \
+ .muxval = _val, \
+}
+
+int ma35_pinctrl_probe(struct platform_device *pdev, const struct ma35_pinctrl_soc_info *info);
+int ma35_pinctrl_suspend(struct device *dev);
+int ma35_pinctrl_resume(struct device *dev);
+
+#endif /* __PINCTRL_MA35_H */
diff --git a/drivers/pinctrl/nuvoton/pinctrl-ma35d1.c b/drivers/pinctrl/nuvoton/pinctrl-ma35d1.c
new file mode 100644
index 000000000000..36510c0b0690
--- /dev/null
+++ b/drivers/pinctrl/nuvoton/pinctrl-ma35d1.c
@@ -0,0 +1,1797 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2023 Nuvoton Technology Corp.
+ *
+ * Author: Shan-Chun Hung <[email protected]>
+ */
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-ma35.h"
+
+static const struct pinctrl_pin_desc ma35d1_pins[] = {
+ MA35_PIN(0, PA0, 0x80, 0x0,
+ MA35_MUX(0x0, "GPA0"),
+ MA35_MUX(0x2, "UART1_nCTS"),
+ MA35_MUX(0x3, "UART16_RXD"),
+ MA35_MUX(0x6, "NAND_DATA0"),
+ MA35_MUX(0x7, "EBI_AD0"),
+ MA35_MUX(0x9, "EBI_ADR0")),
+ MA35_PIN(1, PA1, 0x80, 0x4,
+ MA35_MUX(0x0, "GPA1"),
+ MA35_MUX(0x2, "UART1_nRTS"),
+ MA35_MUX(0x3, "UART16_TXD"),
+ MA35_MUX(0x6, "NAND_DATA1"),
+ MA35_MUX(0x7, "EBI_AD1"),
+ MA35_MUX(0x9, "EBI_ADR1")),
+ MA35_PIN(2, PA2, 0x80, 0x8,
+ MA35_MUX(0x0, "GPA2"),
+ MA35_MUX(0x2, "UART1_RXD"),
+ MA35_MUX(0x6, "NAND_DATA2"),
+ MA35_MUX(0x7, "EBI_AD2"),
+ MA35_MUX(0x9, "EBI_ADR2")),
+ MA35_PIN(3, PA3, 0x80, 0xc,
+ MA35_MUX(0x0, "GPA3"),
+ MA35_MUX(0x2, "UART1_TXD"),
+ MA35_MUX(0x6, "NAND_DATA3"),
+ MA35_MUX(0x7, "EBI_AD3"),
+ MA35_MUX(0x9, "EBI_ADR3")),
+ MA35_PIN(4, PA4, 0x80, 0x10,
+ MA35_MUX(0x0, "GPA4"),
+ MA35_MUX(0x2, "UART3_nCTS"),
+ MA35_MUX(0x3, "UART2_RXD"),
+ MA35_MUX(0x6, "NAND_DATA4"),
+ MA35_MUX(0x7, "EBI_AD4"),
+ MA35_MUX(0x9, "EBI_ADR4")),
+ MA35_PIN(5, PA5, 0x80, 0x14,
+ MA35_MUX(0x0, "GPA5"),
+ MA35_MUX(0x2, "UART3_nRTS"),
+ MA35_MUX(0x3, "UART2_TXD"),
+ MA35_MUX(0x6, "NAND_DATA5"),
+ MA35_MUX(0x7, "EBI_AD5"),
+ MA35_MUX(0x9, "EBI_ADR5")),
+ MA35_PIN(6, PA6, 0x80, 0x18,
+ MA35_MUX(0x0, "GPA6"),
+ MA35_MUX(0x2, "UART3_RXD"),
+ MA35_MUX(0x6, "NAND_DATA6"),
+ MA35_MUX(0x7, "EBI_AD6"),
+ MA35_MUX(0x9, "EBI_ADR6")),
+ MA35_PIN(7, PA7, 0x80, 0x1c,
+ MA35_MUX(0x0, "GPA7"),
+ MA35_MUX(0x2, "UART3_TXD"),
+ MA35_MUX(0x6, "NAND_DATA7"),
+ MA35_MUX(0x7, "EBI_AD7"),
+ MA35_MUX(0x9, "EBI_ADR7")),
+ MA35_PIN(8, PA8, 0x84, 0x0,
+ MA35_MUX(0x0, "GPA8"),
+ MA35_MUX(0x2, "UART5_nCTS"),
+ MA35_MUX(0x3, "UART4_RXD"),
+ MA35_MUX(0x6, "NAND_RDY0"),
+ MA35_MUX(0x7, "EBI_AD8"),
+ MA35_MUX(0x9, "EBI_ADR8")),
+ MA35_PIN(9, PA9, 0x84, 0x4,
+ MA35_MUX(0x0, "GPA9"),
+ MA35_MUX(0x2, "UART5_nRTS"),
+ MA35_MUX(0x3, "UART4_TXD"),
+ MA35_MUX(0x6, "NAND_nRE"),
+ MA35_MUX(0x7, "EBI_AD9"),
+ MA35_MUX(0x9, "EBI_ADR9")),
+ MA35_PIN(10, PA10, 0x84, 0x8,
+ MA35_MUX(0x0, "GPA10"),
+ MA35_MUX(0x2, "UART5_RXD"),
+ MA35_MUX(0x6, "NAND_nWE"),
+ MA35_MUX(0x7, "EBI_AD10"),
+ MA35_MUX(0x9, "EBI_ADR10")),
+ MA35_PIN(11, PA11, 0x84, 0xc,
+ MA35_MUX(0x0, "GPA11"),
+ MA35_MUX(0x2, "UART5_TXD"),
+ MA35_MUX(0x6, "NAND_CLE"),
+ MA35_MUX(0x7, "EBI_AD11"),
+ MA35_MUX(0x9, "EBI_ADR11")),
+ MA35_PIN(12, PA12, 0x84, 0x10,
+ MA35_MUX(0x0, "GPA12"),
+ MA35_MUX(0x2, "UART7_nCTS"),
+ MA35_MUX(0x3, "UART8_RXD"),
+ MA35_MUX(0x6, "NAND_ALE"),
+ MA35_MUX(0x7, "EBI_AD12"),
+ MA35_MUX(0x9, "EBI_ADR12")),
+ MA35_PIN(13, PA13, 0x84, 0x14,
+ MA35_MUX(0x0, "GPA13"),
+ MA35_MUX(0x2, "UART7_nRTS"),
+ MA35_MUX(0x3, "UART8_TXD"),
+ MA35_MUX(0x6, "NAND_nCS0"),
+ MA35_MUX(0x7, "EBI_AD13"),
+ MA35_MUX(0x9, "EBI_ADR13")),
+ MA35_PIN(14, PA14, 0x84, 0x18,
+ MA35_MUX(0x0, "GPA14"),
+ MA35_MUX(0x2, "UART7_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x6, "NAND_nWP"),
+ MA35_MUX(0x7, "EBI_AD14"),
+ MA35_MUX(0x9, "EBI_ADR14")),
+ MA35_PIN(15, PA15, 0x84, 0x1c,
+ MA35_MUX(0x0, "GPA15"),
+ MA35_MUX(0x1, "EPWM0_CH2"),
+ MA35_MUX(0x2, "UART9_nCTS"),
+ MA35_MUX(0x3, "UART6_RXD"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x5, "CAN2_RXD"),
+ MA35_MUX(0x7, "EBI_ALE"),
+ MA35_MUX(0x9, "QEI0_A"),
+ MA35_MUX(0xb, "TM1"),
+ MA35_MUX(0xe, "RGMII0_PPS"),
+ MA35_MUX(0xf, "RMII0_PPS")),
+ MA35_PIN(16, PB0, 0x88, 0x0,
+ MA35_MUX(0x0, "GPB0"),
+ MA35_MUX(0x8, "EADC0_CH0")),
+ MA35_PIN(17, PB1, 0x88, 0x4,
+ MA35_MUX(0x0, "GPB1"),
+ MA35_MUX(0x8, "EADC0_CH1")),
+ MA35_PIN(18, PB2, 0x88, 0x8,
+ MA35_MUX(0x0, "GPB2"),
+ MA35_MUX(0x8, "EADC0_CH2")),
+ MA35_PIN(19, PB3, 0x88, 0xc,
+ MA35_MUX(0x0, "GPB3"),
+ MA35_MUX(0x8, "EADC0_CH3")),
+ MA35_PIN(20, PB4, 0x88, 0x10,
+ MA35_MUX(0x0, "GPB4"),
+ MA35_MUX(0x8, "EADC0_CH4")),
+ MA35_PIN(21, PB5, 0x88, 0x14,
+ MA35_MUX(0x0, "GPB5"),
+ MA35_MUX(0x8, "EADC0_CH5")),
+ MA35_PIN(22, PB6, 0x88, 0x18,
+ MA35_MUX(0x0, "GPB6"),
+ MA35_MUX(0x8, "EADC0_CH6")),
+ MA35_PIN(23, PB7, 0x88, 0x1c,
+ MA35_MUX(0x0, "GPB7"),
+ MA35_MUX(0x8, "EADC0_CH7")),
+ MA35_PIN(24, PB8, 0x8c, 0x0,
+ MA35_MUX(0x0, "GPB8"),
+ MA35_MUX(0x1, "EPWM2_BRAKE0"),
+ MA35_MUX(0x2, "UART2_nCTS"),
+ MA35_MUX(0x3, "UART1_RXD"),
+ MA35_MUX(0x4, "I2C2_SDA"),
+ MA35_MUX(0x5, "SPI0_SS1"),
+ MA35_MUX(0x6, "SPI0_I2SMCLK"),
+ MA35_MUX(0x8, "ADC0_CH0"),
+ MA35_MUX(0x9, "EBI_nCS0"),
+ MA35_MUX(0xb, "TM4"),
+ MA35_MUX(0xe, "QEI2_INDEX"),
+ MA35_MUX(0xf, "KPI_ROW6")),
+ MA35_PIN(25, PB9, 0x8c, 0x4,
+ MA35_MUX(0x0, "GPB9"),
+ MA35_MUX(0x1, "EPWM2_CH4"),
+ MA35_MUX(0x2, "UART2_nRTS"),
+ MA35_MUX(0x3, "UART1_TXD"),
+ MA35_MUX(0x4, "I2C2_SCL"),
+ MA35_MUX(0x5, "SPI0_CLK"),
+ MA35_MUX(0x6, "I2S0_MCLK"),
+ MA35_MUX(0x7, "CCAP1_HSYNC"),
+ MA35_MUX(0x8, "ADC0_CH1"),
+ MA35_MUX(0x9, "EBI_ALE"),
+ MA35_MUX(0xa, "EBI_AD13"),
+ MA35_MUX(0xb, "TM0_EXT"),
+ MA35_MUX(0xc, "I2S1_MCLK"),
+ MA35_MUX(0xd, "SC0_nCD"),
+ MA35_MUX(0xe, "QEI2_A"),
+ MA35_MUX(0xf, "KPI_ROW7")),
+ MA35_PIN(26, PB10, 0x8c, 0x8,
+ MA35_MUX(0x0, "GPB10"),
+ MA35_MUX(0x1, "EPWM2_CH5"),
+ MA35_MUX(0x2, "UART2_RXD"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x5, "SPI0_MOSI"),
+ MA35_MUX(0x6, "EBI_MCLK"),
+ MA35_MUX(0x7, "CCAP1_VSYNC"),
+ MA35_MUX(0x8, "ADC0_CH2"),
+ MA35_MUX(0x9, "EBI_ADR15"),
+ MA35_MUX(0xa, "EBI_AD14"),
+ MA35_MUX(0xb, "TM5"),
+ MA35_MUX(0xc, "I2C1_SDA"),
+ MA35_MUX(0xd, "INT1"),
+ MA35_MUX(0xe, "QEI2_B")),
+ MA35_PIN(27, PB11, 0x8c, 0xc,
+ MA35_MUX(0x0, "GPB11"),
+ MA35_MUX(0x1, "EPWM2_BRAKE1"),
+ MA35_MUX(0x2, "UART2_TXD"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x5, "SPI0_MISO"),
+ MA35_MUX(0x6, "I2S1_MCLK"),
+ MA35_MUX(0x7, "CCAP1_SFIELD"),
+ MA35_MUX(0x8, "ADC0_CH3"),
+ MA35_MUX(0x9, "EBI_nCS2"),
+ MA35_MUX(0xa, "EBI_ALE"),
+ MA35_MUX(0xb, "TM5_EXT"),
+ MA35_MUX(0xc, "I2C1_SCL"),
+ MA35_MUX(0xd, "INT2"),
+ MA35_MUX(0xe, "QEI2_INDEX")),
+ MA35_PIN(28, PB12, 0x8c, 0x10,
+ MA35_MUX(0x0, "GPB12"),
+ MA35_MUX(0x1, "EPWM2_CH0"),
+ MA35_MUX(0x2, "UART4_nCTS"),
+ MA35_MUX(0x3, "UART3_RXD"),
+ MA35_MUX(0x4, "I2C3_SDA"),
+ MA35_MUX(0x5, "CAN2_RXD"),
+ MA35_MUX(0x6, "I2S1_LRCK"),
+ MA35_MUX(0x8, "ADC0_CH4"),
+ MA35_MUX(0x9, "EBI_ADR16"),
+ MA35_MUX(0xe, "ECAP2_IC0")),
+ MA35_PIN(29, PB13, 0x8c, 0x14,
+ MA35_MUX(0x0, "GPB13"),
+ MA35_MUX(0x1, "EPWM2_CH1"),
+ MA35_MUX(0x2, "UART4_nRTS"),
+ MA35_MUX(0x3, "UART3_TXD"),
+ MA35_MUX(0x4, "I2C3_SCL"),
+ MA35_MUX(0x5, "CAN2_TXD"),
+ MA35_MUX(0x6, "I2S1_BCLK"),
+ MA35_MUX(0x8, "ADC0_CH5"),
+ MA35_MUX(0x9, "EBI_ADR17"),
+ MA35_MUX(0xe, "ECAP2_IC1")),
+ MA35_PIN(30, PB14, 0x8c, 0x18,
+ MA35_MUX(0x0, "GPB14"),
+ MA35_MUX(0x1, "EPWM2_CH2"),
+ MA35_MUX(0x2, "UART4_RXD"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x5, "I2C4_SDA"),
+ MA35_MUX(0x6, "I2S1_DI"),
+ MA35_MUX(0x8, "ADC0_CH6"),
+ MA35_MUX(0x9, "EBI_ADR18"),
+ MA35_MUX(0xe, "ECAP2_IC2")),
+ MA35_PIN(31, PB15, 0x8c, 0x1c,
+ MA35_MUX(0x0, "GPB15"),
+ MA35_MUX(0x1, "EPWM2_CH3"),
+ MA35_MUX(0x2, "UART4_TXD"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x5, "I2C4_SCL"),
+ MA35_MUX(0x6, "I2S1_DO"),
+ MA35_MUX(0x8, "ADC0_CH7"),
+ MA35_MUX(0x9, "EBI_ADR19")),
+ MA35_PIN(32, PC0, 0x90, 0x0,
+ MA35_MUX(0x0, "GPC0"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x6, "SD0_CMD/eMMC0_CMD")),
+ MA35_PIN(33, PC1, 0x90, 0x4,
+ MA35_MUX(0x0, "GPC1"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x6, "SD0_CLK/eMMC0_CLK")),
+ MA35_PIN(34, PC2, 0x90, 0x8,
+ MA35_MUX(0x0, "GPC2"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x6, "SD0_DAT0/eMMC0_DAT0")),
+ MA35_PIN(35, PC3, 0x90, 0xc,
+ MA35_MUX(0x0, "GPC3"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x6, "SD0_DAT1/eMMC0_DAT1")),
+ MA35_PIN(36, PC4, 0x90, 0x10,
+ MA35_MUX(0x0, "GPC4"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x6, "SD0_DAT2/eMMC0_DAT2")),
+ MA35_PIN(37, PC5, 0x90, 0x14,
+ MA35_MUX(0x0, "GPC5"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x6, "SD0_DAT3/eMMC0_DAT3")),
+ MA35_PIN(38, PC6, 0x90, 0x18,
+ MA35_MUX(0x0, "GPC6"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x6, "SD0_nCD")),
+ MA35_PIN(39, PC7, 0x90, 0x1c,
+ MA35_MUX(0x0, "GPC7"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x6, "SD0_WP")),
+ MA35_PIN(40, PC12, 0x94, 0x10,
+ MA35_MUX(0x0, "GPC12"),
+ MA35_MUX(0x2, "UART12_nCTS"),
+ MA35_MUX(0x3, "UART11_RXD"),
+ MA35_MUX(0x6, "LCM_DATA16")),
+ MA35_PIN(41, PC13, 0x94, 0x14,
+ MA35_MUX(0x0, "GPC13"),
+ MA35_MUX(0x2, "UART12_nRTS"),
+ MA35_MUX(0x3, "UART11_TXD"),
+ MA35_MUX(0x6, "LCM_DATA17")),
+ MA35_PIN(42, PC14, 0x94, 0x18,
+ MA35_MUX(0x0, "GPC14"),
+ MA35_MUX(0x2, "UART12_RXD"),
+ MA35_MUX(0x6, "LCM_DATA18")),
+ MA35_PIN(43, PC15, 0x94, 0x1c,
+ MA35_MUX(0x0, "GPC15"),
+ MA35_MUX(0x2, "UART12_TXD"),
+ MA35_MUX(0x6, "LCM_DATA19"),
+ MA35_MUX(0x7, "LCM_MPU_TE"),
+ MA35_MUX(0x8, "LCM_MPU_VSYNC")),
+ MA35_PIN(44, PD0, 0x98, 0x0,
+ MA35_MUX(0x0, "GPD0"),
+ MA35_MUX(0x2, "UART3_nCTS"),
+ MA35_MUX(0x3, "UART4_RXD"),
+ MA35_MUX(0x5, "QSPI0_SS0")),
+ MA35_PIN(45, PD1, 0x98, 0x4,
+ MA35_MUX(0x0, "GPD1"),
+ MA35_MUX(0x2, "UART3_nRTS"),
+ MA35_MUX(0x3, "UART4_TXD"),
+ MA35_MUX(0x5, "QSPI0_CLK")),
+ MA35_PIN(46, PD2, 0x98, 0x8,
+ MA35_MUX(0x0, "GPD2"),
+ MA35_MUX(0x2, "UART3_RXD"),
+ MA35_MUX(0x5, "QSPI0_MOSI0")),
+ MA35_PIN(47, PD3, 0x98, 0xc,
+ MA35_MUX(0x0, "GPD3"),
+ MA35_MUX(0x2, "UART3_TXD"),
+ MA35_MUX(0x5, "QSPI0_MISO0")),
+ MA35_PIN(48, PD4, 0x98, 0x10,
+ MA35_MUX(0x0, "GPD4"),
+ MA35_MUX(0x2, "UART1_nCTS"),
+ MA35_MUX(0x3, "UART2_RXD"),
+ MA35_MUX(0x4, "I2C2_SDA"),
+ MA35_MUX(0x5, "QSPI0_MOSI1")),
+ MA35_PIN(49, PD5, 0x98, 0x14,
+ MA35_MUX(0x0, "GPD5"),
+ MA35_MUX(0x2, "UART1_nRTS"),
+ MA35_MUX(0x3, "UART2_TXD"),
+ MA35_MUX(0x4, "I2C2_SCL"),
+ MA35_MUX(0x5, "QSPI0_MISO1")),
+ MA35_PIN(50, PD6, 0x98, 0x18,
+ MA35_MUX(0x0, "GPD6"),
+ MA35_MUX(0x1, "EPWM0_SYNC_IN"),
+ MA35_MUX(0x2, "UART1_RXD"),
+ MA35_MUX(0x5, "QSPI1_MOSI1"),
+ MA35_MUX(0x6, "I2C0_SDA"),
+ MA35_MUX(0x7, "I2S0_MCLK"),
+ MA35_MUX(0x8, "EPWM0_CH0"),
+ MA35_MUX(0x9, "EBI_AD5"),
+ MA35_MUX(0xa, "SPI3_SS1"),
+ MA35_MUX(0xb, "TRACE_CLK")),
+ MA35_PIN(51, PD7, 0x98, 0x1c,
+ MA35_MUX(0x0, "GPD7"),
+ MA35_MUX(0x1, "EPWM0_SYNC_OUT"),
+ MA35_MUX(0x2, "UART1_TXD"),
+ MA35_MUX(0x5, "QSPI1_MISO1"),
+ MA35_MUX(0x6, "I2C0_SCL"),
+ MA35_MUX(0x7, "I2S1_MCLK"),
+ MA35_MUX(0x8, "EPWM0_CH1"),
+ MA35_MUX(0x9, "EBI_AD6"),
+ MA35_MUX(0xa, "SC1_nCD"),
+ MA35_MUX(0xb, "EADC0_ST")),
+ MA35_PIN(52, PD8, 0x9c, 0x0,
+ MA35_MUX(0x0, "GPD8"),
+ MA35_MUX(0x1, "EPWM0_BRAKE0"),
+ MA35_MUX(0x2, "UART16_nCTS"),
+ MA35_MUX(0x3, "UART15_RXD"),
+ MA35_MUX(0x5, "QSPI1_SS0"),
+ MA35_MUX(0x7, "I2S1_LRCK"),
+ MA35_MUX(0x8, "EPWM0_CH2"),
+ MA35_MUX(0x9, "EBI_AD7"),
+ MA35_MUX(0xa, "SC1_CLK"),
+ MA35_MUX(0xb, "TM0")),
+ MA35_PIN(53, PD9, 0x9c, 0x4,
+ MA35_MUX(0x0, "GPD9"),
+ MA35_MUX(0x1, "EPWM0_BRAKE1"),
+ MA35_MUX(0x2, "UART16_nRTS"),
+ MA35_MUX(0x3, "UART15_TXD"),
+ MA35_MUX(0x5, "QSPI1_CLK"),
+ MA35_MUX(0x7, "I2S1_BCLK"),
+ MA35_MUX(0x8, "EPWM0_CH3"),
+ MA35_MUX(0x9, "EBI_AD8"),
+ MA35_MUX(0xa, "SC1_DAT"),
+ MA35_MUX(0xb, "TM0_EXT")),
+ MA35_PIN(54, PD10, 0x9c, 0x8,
+ MA35_MUX(0x0, "GPD10"),
+ MA35_MUX(0x1, "EPWM1_BRAKE0"),
+ MA35_MUX(0x2, "UART16_RXD"),
+ MA35_MUX(0x5, "QSPI1_MOSI0"),
+ MA35_MUX(0x7, "I2S1_DI"),
+ MA35_MUX(0x8, "EPWM0_CH4"),
+ MA35_MUX(0x9, "EBI_AD9"),
+ MA35_MUX(0xa, "SC1_RST"),
+ MA35_MUX(0xb, "TM2")),
+ MA35_PIN(55, PD11, 0x9c, 0xc,
+ MA35_MUX(0x0, "GPD11"),
+ MA35_MUX(0x1, "EPWM1_BRAKE1"),
+ MA35_MUX(0x2, "UART16_TXD"),
+ MA35_MUX(0x5, "QSPI1_MISO0"),
+ MA35_MUX(0x7, "I2S1_DO"),
+ MA35_MUX(0x8, "EPWM0_CH5"),
+ MA35_MUX(0x9, "EBI_AD10"),
+ MA35_MUX(0xa, "SC1_PWR"),
+ MA35_MUX(0xb, "TM2_EXT")),
+ MA35_PIN(56, PD12, 0x9c, 0x10,
+ MA35_MUX(0x0, "GPD12"),
+ MA35_MUX(0x1, "EPWM0_BRAKE0"),
+ MA35_MUX(0x2, "UART11_TXD"),
+ MA35_MUX(0x3, "UART10_RXD"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x6, "TRACE_DATA0"),
+ MA35_MUX(0x7, "EBI_nCS1"),
+ MA35_MUX(0x8, "EBI_AD4"),
+ MA35_MUX(0x9, "QEI0_INDEX"),
+ MA35_MUX(0xb, "TM5"),
+ MA35_MUX(0xc, "I2S1_LRCK"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(57, PD13, 0x9c, 0x14,
+ MA35_MUX(0x0, "GPD13"),
+ MA35_MUX(0x1, "EPWM0_BRAKE1"),
+ MA35_MUX(0x2, "UART11_RXD"),
+ MA35_MUX(0x3, "UART10_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x6, "TRACE_DATA1"),
+ MA35_MUX(0x7, "EBI_nCS2"),
+ MA35_MUX(0x8, "EBI_AD5"),
+ MA35_MUX(0x9, "ECAP0_IC0"),
+ MA35_MUX(0xb, "TM5_EXT"),
+ MA35_MUX(0xc, "I2S1_BCLK")),
+ MA35_PIN(58, PD14, 0x9c, 0x18,
+ MA35_MUX(0x0, "GPD14"),
+ MA35_MUX(0x1, "EPWM0_SYNC_IN"),
+ MA35_MUX(0x2, "UART11_nCTS"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x6, "TRACE_DATA2"),
+ MA35_MUX(0x7, "EBI_MCLK"),
+ MA35_MUX(0x8, "EBI_AD6"),
+ MA35_MUX(0x9, "ECAP0_IC1"),
+ MA35_MUX(0xb, "TM6"),
+ MA35_MUX(0xc, "I2S1_DI"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(59, PD15, 0x9c, 0x1c,
+ MA35_MUX(0x0, "GPD15"),
+ MA35_MUX(0x1, "EPWM0_SYNC_OUT"),
+ MA35_MUX(0x2, "UART11_nRTS"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x6, "TRACE_DATA3"),
+ MA35_MUX(0x7, "EBI_ALE"),
+ MA35_MUX(0x8, "EBI_AD7"),
+ MA35_MUX(0x9, "ECAP0_IC2"),
+ MA35_MUX(0xb, "TM6_EXT"),
+ MA35_MUX(0xc, "I2S1_DO")),
+ MA35_PIN(60, PE0, 0xa0, 0x0,
+ MA35_MUX(0x0, "GPE0"),
+ MA35_MUX(0x2, "UART9_nCTS"),
+ MA35_MUX(0x3, "UART8_RXD"),
+ MA35_MUX(0x7, "CCAP1_DATA0"),
+ MA35_MUX(0x8, "RGMII0_MDC"),
+ MA35_MUX(0x9, "RMII0_MDC")),
+ MA35_PIN(61, PE1, 0xa0, 0x4,
+ MA35_MUX(0x0, "GPE1"),
+ MA35_MUX(0x2, "UART9_nRTS"),
+ MA35_MUX(0x3, "UART8_TXD"),
+ MA35_MUX(0x7, "CCAP1_DATA1"),
+ MA35_MUX(0x8, "RGMII0_MDIO"),
+ MA35_MUX(0x9, "RMII0_MDIO")),
+ MA35_PIN(62, PE2, 0xa0, 0x8,
+ MA35_MUX(0x0, "GPE2"),
+ MA35_MUX(0x2, "UART9_RXD"),
+ MA35_MUX(0x7, "CCAP1_DATA2"),
+ MA35_MUX(0x8, "RGMII0_TXCTL"),
+ MA35_MUX(0x9, "RMII0_TXEN")),
+ MA35_PIN(63, PE3, 0xa0, 0xc,
+ MA35_MUX(0x0, "GPE3"),
+ MA35_MUX(0x2, "UART9_TXD"),
+ MA35_MUX(0x7, "CCAP1_DATA3"),
+ MA35_MUX(0x8, "RGMII0_TXD0"),
+ MA35_MUX(0x9, "RMII0_TXD0")),
+ MA35_PIN(64, PE4, 0xa0, 0x10,
+ MA35_MUX(0x0, "GPE4"),
+ MA35_MUX(0x2, "UART4_nCTS"),
+ MA35_MUX(0x3, "UART3_RXD"),
+ MA35_MUX(0x7, "CCAP1_DATA4"),
+ MA35_MUX(0x8, "RGMII0_TXD1"),
+ MA35_MUX(0x9, "RMII0_TXD1")),
+ MA35_PIN(65, PE5, 0xa0, 0x14,
+ MA35_MUX(0x0, "GPE5"),
+ MA35_MUX(0x2, "UART4_nRTS"),
+ MA35_MUX(0x3, "UART3_TXD"),
+ MA35_MUX(0x7, "CCAP1_DATA5"),
+ MA35_MUX(0x8, "RGMII0_RXCLK"),
+ MA35_MUX(0x9, "RMII0_REFCLK")),
+ MA35_PIN(66, PE6, 0xa0, 0x18,
+ MA35_MUX(0x0, "GPE6"),
+ MA35_MUX(0x2, "UART4_RXD"),
+ MA35_MUX(0x7, "CCAP1_DATA6"),
+ MA35_MUX(0x8, "RGMII0_RXCTL"),
+ MA35_MUX(0x9, "RMII0_CRSDV")),
+ MA35_PIN(67, PE7, 0xa0, 0x1c,
+ MA35_MUX(0x0, "GPE7"),
+ MA35_MUX(0x2, "UART4_TXD"),
+ MA35_MUX(0x7, "CCAP1_DATA7"),
+ MA35_MUX(0x8, "RGMII0_RXD0"),
+ MA35_MUX(0x9, "RMII0_RXD0")),
+ MA35_PIN(68, PE8, 0xa4, 0x0,
+ MA35_MUX(0x0, "GPE8"),
+ MA35_MUX(0x2, "UART13_nCTS"),
+ MA35_MUX(0x3, "UART12_RXD"),
+ MA35_MUX(0x7, "CCAP1_SCLK"),
+ MA35_MUX(0x8, "RGMII0_RXD1"),
+ MA35_MUX(0x9, "RMII0_RXD1")),
+ MA35_PIN(69, PE9, 0xa4, 0x4,
+ MA35_MUX(0x0, "GPE9"),
+ MA35_MUX(0x2, "UART13_nRTS"),
+ MA35_MUX(0x3, "UART12_TXD"),
+ MA35_MUX(0x7, "CCAP1_PIXCLK"),
+ MA35_MUX(0x8, "RGMII0_RXD2"),
+ MA35_MUX(0x9, "RMII0_RXERR")),
+ MA35_PIN(70, PE10, 0xa4, 0x8,
+ MA35_MUX(0x0, "GPE10"),
+ MA35_MUX(0x2, "UART15_nCTS"),
+ MA35_MUX(0x3, "UART14_RXD"),
+ MA35_MUX(0x5, "SPI1_SS0"),
+ MA35_MUX(0x7, "CCAP1_HSYNC"),
+ MA35_MUX(0x8, "RGMII0_RXD3")),
+ MA35_PIN(71, PE11, 0xa4, 0xc,
+ MA35_MUX(0x0, "GPE11"),
+ MA35_MUX(0x2, "UART15_nRTS"),
+ MA35_MUX(0x3, "UART14_TXD"),
+ MA35_MUX(0x5, "SPI1_CLK"),
+ MA35_MUX(0x7, "CCAP1_VSYNC"),
+ MA35_MUX(0x8, "RGMII0_TXCLK")),
+ MA35_PIN(72, PE12, 0xa4, 0x10,
+ MA35_MUX(0x0, "GPE12"),
+ MA35_MUX(0x2, "UART15_RXD"),
+ MA35_MUX(0x5, "SPI1_MOSI"),
+ MA35_MUX(0x7, "CCAP1_DATA8"),
+ MA35_MUX(0x8, "RGMII0_TXD2")),
+ MA35_PIN(73, PE13, 0xa4, 0x14,
+ MA35_MUX(0x0, "GPE13"),
+ MA35_MUX(0x2, "UART15_TXD"),
+ MA35_MUX(0x5, "SPI1_MISO"),
+ MA35_MUX(0x7, "CCAP1_DATA9"),
+ MA35_MUX(0x8, "RGMII0_TXD3")),
+ MA35_PIN(74, PE14, 0xa4, 0x18,
+ MA35_MUX(0x0, "GPE14"),
+ MA35_MUX(0x1, "UART0_TXD")),
+ MA35_PIN(75, PE15, 0xa4, 0x1c,
+ MA35_MUX(0x0, "GPE15"),
+ MA35_MUX(0x1, "UART0_RXD")),
+ MA35_PIN(76, PF0, 0xa8, 0x0,
+ MA35_MUX(0x0, "GPF0"),
+ MA35_MUX(0x2, "UART2_nCTS"),
+ MA35_MUX(0x3, "UART1_RXD"),
+ MA35_MUX(0x6, "RGMII0_RXD3"),
+ MA35_MUX(0x8, "RGMII1_MDC"),
+ MA35_MUX(0x9, "RMII1_MDC"),
+ MA35_MUX(0xe, "KPI_COL0")),
+ MA35_PIN(77, PF1, 0xa8, 0x4,
+ MA35_MUX(0x0, "GPF1"),
+ MA35_MUX(0x2, "UART2_nRTS"),
+ MA35_MUX(0x3, "UART1_TXD"),
+ MA35_MUX(0x6, "RGMII0_TXCLK"),
+ MA35_MUX(0x8, "RGMII1_MDIO"),
+ MA35_MUX(0x9, "RMII1_MDIO"),
+ MA35_MUX(0xe, "KPI_COL1")),
+ MA35_PIN(78, PF2, 0xa8, 0x8,
+ MA35_MUX(0x0, "GPF2"),
+ MA35_MUX(0x2, "UART2_RXD"),
+ MA35_MUX(0x6, "RGMII0_TXD2"),
+ MA35_MUX(0x8, "RGMII1_TXCTL"),
+ MA35_MUX(0x9, "RMII1_TXEN"),
+ MA35_MUX(0xe, "KPI_COL2")),
+ MA35_PIN(79, PF3, 0xa8, 0xc,
+ MA35_MUX(0x0, "GPF3"),
+ MA35_MUX(0x2, "UART2_TXD"),
+ MA35_MUX(0x6, "RGMII0_TXD3"),
+ MA35_MUX(0x8, "RGMII1_TXD0"),
+ MA35_MUX(0x9, "RMII1_TXD0"),
+ MA35_MUX(0xe, "KPI_COL3")),
+ MA35_PIN(80, PF4, 0xa8, 0x10,
+ MA35_MUX(0x0, "GPF4"),
+ MA35_MUX(0x2, "UART11_nCTS"),
+ MA35_MUX(0x3, "UART10_RXD"),
+ MA35_MUX(0x4, "I2S0_LRCK"),
+ MA35_MUX(0x5, "SPI1_SS0"),
+ MA35_MUX(0x8, "RGMII1_TXD1"),
+ MA35_MUX(0x9, "RMII1_TXD1"),
+ MA35_MUX(0xd, "CAN2_RXD"),
+ MA35_MUX(0xe, "KPI_ROW0")),
+ MA35_PIN(81, PF5, 0xa8, 0x14,
+ MA35_MUX(0x0, "GPF5"),
+ MA35_MUX(0x2, "UART11_nRTS"),
+ MA35_MUX(0x3, "UART10_TXD"),
+ MA35_MUX(0x4, "I2S0_BCLK"),
+ MA35_MUX(0x5, "SPI1_CLK"),
+ MA35_MUX(0x8, "RGMII1_RXCLK"),
+ MA35_MUX(0x9, "RMII1_REFCLK"),
+ MA35_MUX(0xd, "CAN2_TXD"),
+ MA35_MUX(0xe, "KPI_ROW1")),
+ MA35_PIN(82, PF6, 0xa8, 0x18,
+ MA35_MUX(0x0, "GPF6"),
+ MA35_MUX(0x2, "UART11_RXD"),
+ MA35_MUX(0x4, "I2S0_DI"),
+ MA35_MUX(0x5, "SPI1_MOSI"),
+ MA35_MUX(0x8, "RGMII1_RXCTL"),
+ MA35_MUX(0x9, "RMII1_CRSDV"),
+ MA35_MUX(0xa, "I2C4_SDA"),
+ MA35_MUX(0xd, "SC0_CLK"),
+ MA35_MUX(0xe, "KPI_ROW2")),
+ MA35_PIN(83, PF7, 0xa8, 0x1c,
+ MA35_MUX(0x0, "GPF7"),
+ MA35_MUX(0x2, "UART11_TXD"),
+ MA35_MUX(0x4, "I2S0_DO"),
+ MA35_MUX(0x5, "SPI1_MISO"),
+ MA35_MUX(0x8, "RGMII1_RXD0"),
+ MA35_MUX(0x9, "RMII1_RXD0"),
+ MA35_MUX(0xa, "I2C4_SCL"),
+ MA35_MUX(0xd, "SC0_DAT"),
+ MA35_MUX(0xe, "KPI_ROW3")),
+ MA35_PIN(84, PF8, 0xac, 0x0,
+ MA35_MUX(0x0, "GPF8"),
+ MA35_MUX(0x2, "UART13_RXD"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x5, "SPI0_SS0"),
+ MA35_MUX(0x8, "RGMII1_RXD1"),
+ MA35_MUX(0x9, "RMII1_RXD1"),
+ MA35_MUX(0xd, "SC0_RST"),
+ MA35_MUX(0xe, "KPI_COL4")),
+ MA35_PIN(85, PF9, 0xac, 0x4,
+ MA35_MUX(0x0, "GPF9"),
+ MA35_MUX(0x2, "UART13_TXD"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x5, "SPI0_SS1"),
+ MA35_MUX(0x8, "RGMII1_RXD2"),
+ MA35_MUX(0x9, "RMII1_RXERR"),
+ MA35_MUX(0xd, "SC0_PWR"),
+ MA35_MUX(0xe, "KPI_COL5")),
+ MA35_PIN(86, PF10, 0xac, 0x8,
+ MA35_MUX(0x0, "GPF10"),
+ MA35_MUX(0x2, "UART13_nCTS"),
+ MA35_MUX(0x5, "I2S0_LRCK"),
+ MA35_MUX(0x6, "SPI1_SS0"),
+ MA35_MUX(0x8, "RGMII1_RXD3"),
+ MA35_MUX(0x9, "SC0_CLK"),
+ MA35_MUX(0xe, "KPI_COL6")),
+ MA35_PIN(87, PF11, 0xac, 0xc,
+ MA35_MUX(0x0, "GPF11"),
+ MA35_MUX(0x2, "UART13_nRTS"),
+ MA35_MUX(0x5, "I2S0_BCLK"),
+ MA35_MUX(0x6, "SPI1_CLK"),
+ MA35_MUX(0x8, "RGMII1_TXCLK"),
+ MA35_MUX(0x9, "SC0_DAT"),
+ MA35_MUX(0xe, "KPI_COL7")),
+ MA35_PIN(88, PF12, 0xac, 0x10,
+ MA35_MUX(0x0, "GPF12"),
+ MA35_MUX(0x5, "I2S0_DI"),
+ MA35_MUX(0x6, "SPI1_MOSI"),
+ MA35_MUX(0x8, "RGMII1_TXD2"),
+ MA35_MUX(0x9, "SC0_RST"),
+ MA35_MUX(0xe, "KPI_ROW4")),
+ MA35_PIN(89, PF13, 0xac, 0x14,
+ MA35_MUX(0x0, "GPF13"),
+ MA35_MUX(0x5, "I2S0_DO"),
+ MA35_MUX(0x6, "SPI1_MISO"),
+ MA35_MUX(0x8, "RGMII1_TXD3"),
+ MA35_MUX(0x9, "SC0_PWR"),
+ MA35_MUX(0xe, "KPI_ROW5")),
+ MA35_PIN(90, PF14, 0xac, 0x18,
+ MA35_MUX(0x0, "GPF14"),
+ MA35_MUX(0x1, "EPWM2_BRAKE0"),
+ MA35_MUX(0x2, "EADC0_ST"),
+ MA35_MUX(0x3, "RGMII1_PPS"),
+ MA35_MUX(0x4, "RMII1_PPS"),
+ MA35_MUX(0x5, "SPI0_I2SMCLK"),
+ MA35_MUX(0x6, "SPI1_I2SMCLK"),
+ MA35_MUX(0x7, "CCAP1_SFIELD"),
+ MA35_MUX(0x8, "RGMII0_PPS"),
+ MA35_MUX(0x9, "RMII0_PPS"),
+ MA35_MUX(0xb, "TM0"),
+ MA35_MUX(0xc, "INT0"),
+ MA35_MUX(0xd, "SPI1_SS1"),
+ MA35_MUX(0xe, "QEI2_INDEX"),
+ MA35_MUX(0xf, "I2S0_MCLK")),
+ MA35_PIN(91, PF15, 0xac, 0x1c,
+ MA35_MUX(0x0, "GPF15"),
+ MA35_MUX(0x1, "HSUSB0_VBUSVLD")),
+ MA35_PIN(92, PG0, 0xb0, 0x0,
+ MA35_MUX(0x0, "GPG0"),
+ MA35_MUX(0x1, "EPWM0_CH0"),
+ MA35_MUX(0x2, "UART7_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "SPI0_SS0"),
+ MA35_MUX(0x6, "EADC0_ST"),
+ MA35_MUX(0x7, "EBI_AD15"),
+ MA35_MUX(0x9, "I2S1_MCLK"),
+ MA35_MUX(0xa, "QEI0_INDEX"),
+ MA35_MUX(0xb, "TM1"),
+ MA35_MUX(0xc, "CLKO"),
+ MA35_MUX(0xd, "INT0"),
+ MA35_MUX(0xf, "EBI_ADR15")),
+ MA35_PIN(93, PG1, 0xb0, 0x4,
+ MA35_MUX(0x0, "GPG1"),
+ MA35_MUX(0x1, "EPWM0_CH3"),
+ MA35_MUX(0x2, "UART9_nRTS"),
+ MA35_MUX(0x3, "UART6_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x5, "CAN2_TXD"),
+ MA35_MUX(0x7, "EBI_nCS0"),
+ MA35_MUX(0x9, "QEI0_B"),
+ MA35_MUX(0xb, "TM1_EXT"),
+ MA35_MUX(0xe, "RGMII1_PPS"),
+ MA35_MUX(0xf, "RMII1_PPS")),
+ MA35_PIN(94, PG2, 0xb0, 0x8,
+ MA35_MUX(0x0, "GPG2"),
+ MA35_MUX(0x1, "EPWM0_CH4"),
+ MA35_MUX(0x2, "UART9_RXD"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x5, "SPI0_SS1"),
+ MA35_MUX(0x7, "EBI_ADR16"),
+ MA35_MUX(0x8, "EBI_nCS2"),
+ MA35_MUX(0xa, "QEI0_A"),
+ MA35_MUX(0xb, "TM3"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(95, PG3, 0xb0, 0xc,
+ MA35_MUX(0x0, "GPG3"),
+ MA35_MUX(0x1, "EPWM0_CH5"),
+ MA35_MUX(0x2, "UART9_TXD"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x5, "SPI0_I2SMCLK"),
+ MA35_MUX(0x7, "EBI_ADR17"),
+ MA35_MUX(0x8, "EBI_nCS1"),
+ MA35_MUX(0x9, "EBI_MCLK"),
+ MA35_MUX(0xa, "QEI0_B"),
+ MA35_MUX(0xb, "TM3_EXT"),
+ MA35_MUX(0xc, "I2S1_MCLK")),
+ MA35_PIN(96, PG4, 0xb0, 0x10,
+ MA35_MUX(0x0, "GPG4"),
+ MA35_MUX(0x1, "EPWM1_CH0"),
+ MA35_MUX(0x2, "UART5_nCTS"),
+ MA35_MUX(0x3, "UART6_RXD"),
+ MA35_MUX(0x5, "SPI3_SS0"),
+ MA35_MUX(0x6, "QEI1_INDEX"),
+ MA35_MUX(0x7, "EBI_ADR18"),
+ MA35_MUX(0x8, "EBI_nCS0"),
+ MA35_MUX(0x9, "I2S1_DO"),
+ MA35_MUX(0xa, "SC1_CLK"),
+ MA35_MUX(0xb, "TM4"),
+ MA35_MUX(0xd, "INT2"),
+ MA35_MUX(0xe, "ECAP1_IC2")),
+ MA35_PIN(97, PG5, 0xb0, 0x14,
+ MA35_MUX(0x0, "GPG5"),
+ MA35_MUX(0x1, "EPWM1_CH1"),
+ MA35_MUX(0x2, "UART5_nRTS"),
+ MA35_MUX(0x3, "UART6_TXD"),
+ MA35_MUX(0x5, "SPI3_CLK"),
+ MA35_MUX(0x6, "ECAP0_IC0"),
+ MA35_MUX(0x7, "EBI_ADR19"),
+ MA35_MUX(0x8, "EBI_ALE"),
+ MA35_MUX(0x9, "I2S1_DI"),
+ MA35_MUX(0xa, "SC1_DAT"),
+ MA35_MUX(0xb, "TM4_EXT")),
+ MA35_PIN(98, PG6, 0xb0, 0x18,
+ MA35_MUX(0x0, "GPG6"),
+ MA35_MUX(0x1, "EPWM1_CH2"),
+ MA35_MUX(0x2, "UART5_RXD"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x5, "SPI3_MOSI"),
+ MA35_MUX(0x6, "ECAP0_IC1"),
+ MA35_MUX(0x7, "EBI_nRD"),
+ MA35_MUX(0x9, "I2S1_BCLK"),
+ MA35_MUX(0xa, "SC1_RST"),
+ MA35_MUX(0xb, "TM7"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(99, PG7, 0xb0, 0x1c,
+ MA35_MUX(0x0, "GPG7"),
+ MA35_MUX(0x1, "EPWM1_CH3"),
+ MA35_MUX(0x2, "UART5_TXD"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x5, "SPI3_MISO"),
+ MA35_MUX(0x6, "ECAP0_IC2"),
+ MA35_MUX(0x7, "EBI_nWR"),
+ MA35_MUX(0x9, "I2S1_LRCK"),
+ MA35_MUX(0xa, "SC1_PWR"),
+ MA35_MUX(0xb, "TM7_EXT")),
+ MA35_PIN(100, PG8, 0xb4, 0x0,
+ MA35_MUX(0x0, "GPG8"),
+ MA35_MUX(0x1, "EPWM1_CH4"),
+ MA35_MUX(0x2, "UART12_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "SPI2_SS0"),
+ MA35_MUX(0x6, "LCM_VSYNC"),
+ MA35_MUX(0x7, "I2C3_SDA"),
+ MA35_MUX(0xc, "EBI_AD7"),
+ MA35_MUX(0xd, "EBI_nCS0")),
+ MA35_PIN(101, PG9, 0xb4, 0x4,
+ MA35_MUX(0x0, "GPG9"),
+ MA35_MUX(0x1, "EPWM1_CH5"),
+ MA35_MUX(0x2, "UART12_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "SPI2_CLK"),
+ MA35_MUX(0x6, "LCM_HSYNC"),
+ MA35_MUX(0x7, "I2C3_SCL"),
+ MA35_MUX(0xc, "EBI_AD8"),
+ MA35_MUX(0xd, "EBI_nCS1")),
+ MA35_PIN(102, PG10, 0xb4, 0x8,
+ MA35_MUX(0x0, "GPG10"),
+ MA35_MUX(0x2, "UART12_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x5, "SPI2_MOSI"),
+ MA35_MUX(0x6, "LCM_CLK"),
+ MA35_MUX(0xc, "EBI_AD9"),
+ MA35_MUX(0xd, "EBI_nWRH")),
+ MA35_PIN(103, PG11, 0xb4, 0xc,
+ MA35_MUX(0x0, "GPG11"),
+ MA35_MUX(0x3, "JTAG_TDO"),
+ MA35_MUX(0x5, "I2S0_MCLK"),
+ MA35_MUX(0x6, "NAND_RDY1"),
+ MA35_MUX(0x7, "EBI_nWRH"),
+ MA35_MUX(0x8, "EBI_nCS1"),
+ MA35_MUX(0xa, "EBI_AD0")),
+ MA35_PIN(104, PG12, 0xb4, 0x10,
+ MA35_MUX(0x0, "GPG12"),
+ MA35_MUX(0x3, "JTAG_TCK/SW_CLK"),
+ MA35_MUX(0x5, "I2S0_LRCK"),
+ MA35_MUX(0x7, "EBI_nWRL"),
+ MA35_MUX(0xa, "EBI_AD1")),
+ MA35_PIN(105, PG13, 0xb4, 0x14,
+ MA35_MUX(0x0, "GPG13"),
+ MA35_MUX(0x3, "JTAG_TMS/SW_DIO"),
+ MA35_MUX(0x5, "I2S0_BCLK"),
+ MA35_MUX(0x7, "EBI_MCLK"),
+ MA35_MUX(0xa, "EBI_AD2")),
+ MA35_PIN(106, PG14, 0xb4, 0x18,
+ MA35_MUX(0x0, "GPG14"),
+ MA35_MUX(0x3, "JTAG_TDI"),
+ MA35_MUX(0x5, "I2S0_DI"),
+ MA35_MUX(0x6, "NAND_nCS1"),
+ MA35_MUX(0x7, "EBI_ALE"),
+ MA35_MUX(0xa, "EBI_AD3")),
+ MA35_PIN(107, PG15, 0xb4, 0x1c,
+ MA35_MUX(0x0, "GPG15"),
+ MA35_MUX(0x3, "JTAG_nTRST"),
+ MA35_MUX(0x5, "I2S0_DO"),
+ MA35_MUX(0x7, "EBI_nCS0"),
+ MA35_MUX(0xa, "EBI_AD4")),
+ MA35_PIN(108, PH0, 0xb8, 0x0,
+ MA35_MUX(0x0, "GPH0"),
+ MA35_MUX(0x2, "UART8_nCTS"),
+ MA35_MUX(0x3, "UART7_RXD"),
+ MA35_MUX(0x6, "LCM_DATA8")),
+ MA35_PIN(109, PH1, 0xb8, 0x4,
+ MA35_MUX(0x0, "GPH1"),
+ MA35_MUX(0x2, "UART8_nRTS"),
+ MA35_MUX(0x3, "UART7_TXD"),
+ MA35_MUX(0x6, "LCM_DATA9")),
+ MA35_PIN(110, PH2, 0xb8, 0x8,
+ MA35_MUX(0x0, "GPH2"),
+ MA35_MUX(0x2, "UART8_RXD"),
+ MA35_MUX(0x6, "LCM_DATA10")),
+ MA35_PIN(111, PH3, 0xb8, 0xc,
+ MA35_MUX(0x0, "GPH3"),
+ MA35_MUX(0x2, "UART8_TXD"),
+ MA35_MUX(0x6, "LCM_DATA11")),
+ MA35_PIN(112, PH4, 0xb8, 0x10,
+ MA35_MUX(0x0, "GPH4"),
+ MA35_MUX(0x2, "UART10_nCTS"),
+ MA35_MUX(0x3, "UART9_RXD"),
+ MA35_MUX(0x6, "LCM_DATA12")),
+ MA35_PIN(113, PH5, 0xb8, 0x14,
+ MA35_MUX(0x0, "GPH5"),
+ MA35_MUX(0x2, "UART10_nRTS"),
+ MA35_MUX(0x3, "UART9_TXD"),
+ MA35_MUX(0x6, "LCM_DATA13")),
+ MA35_PIN(114, PH6, 0xb8, 0x18,
+ MA35_MUX(0x0, "GPH6"),
+ MA35_MUX(0x2, "UART10_RXD"),
+ MA35_MUX(0x6, "LCM_DATA14")),
+ MA35_PIN(115, PH7, 0xb8, 0x1c,
+ MA35_MUX(0x0, "GPH7"),
+ MA35_MUX(0x2, "UART10_TXD"),
+ MA35_MUX(0x6, "LCM_DATA15")),
+ MA35_PIN(116, PH8, 0xbc, 0x0,
+ MA35_MUX(0x0, "GPH8"),
+ MA35_MUX(0x6, "TAMPER0")),
+ MA35_PIN(117, PH9, 0xbc, 0x4,
+ MA35_MUX(0x0, "GPH9"),
+ MA35_MUX(0x4, "CLK_32KOUT"),
+ MA35_MUX(0x6, "TAMPER1")),
+ MA35_PIN(118, PH12, 0xbc, 0x10,
+ MA35_MUX(0x0, "GPH12"),
+ MA35_MUX(0x2, "UART14_nCTS"),
+ MA35_MUX(0x3, "UART13_RXD"),
+ MA35_MUX(0x6, "LCM_DATA20")),
+ MA35_PIN(119, PH13, 0xbc, 0x14,
+ MA35_MUX(0x0, "GPH13"),
+ MA35_MUX(0x2, "UART14_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x6, "LCM_DATA21")),
+ MA35_PIN(120, PH14, 0xbc, 0x18,
+ MA35_MUX(0x0, "GPH14"),
+ MA35_MUX(0x2, "UART14_RXD"),
+ MA35_MUX(0x6, "LCM_DATA22")),
+ MA35_PIN(121, PH15, 0xbc, 0x1c,
+ MA35_MUX(0x0, "GPH15"),
+ MA35_MUX(0x2, "UART14_TXD"),
+ MA35_MUX(0x6, "LCM_DATA23")),
+ MA35_PIN(122, PI0, 0xc0, 0x0,
+ MA35_MUX(0x0, "GPI0"),
+ MA35_MUX(0x1, "EPWM0_CH0"),
+ MA35_MUX(0x2, "UART12_nCTS"),
+ MA35_MUX(0x3, "UART11_RXD"),
+ MA35_MUX(0x4, "I2C2_SDA"),
+ MA35_MUX(0x5, "SPI3_SS0"),
+ MA35_MUX(0x7, "SC0_nCD"),
+ MA35_MUX(0x8, "EBI_ADR0"),
+ MA35_MUX(0xb, "TM0"),
+ MA35_MUX(0xc, "ECAP1_IC0")),
+ MA35_PIN(123, PI1, 0xc0, 0x4,
+ MA35_MUX(0x0, "GPI1"),
+ MA35_MUX(0x1, "EPWM0_CH1"),
+ MA35_MUX(0x2, "UART12_nRTS"),
+ MA35_MUX(0x3, "UART11_TXD"),
+ MA35_MUX(0x4, "I2C2_SCL"),
+ MA35_MUX(0x5, "SPI3_CLK"),
+ MA35_MUX(0x7, "SC0_CLK"),
+ MA35_MUX(0x8, "EBI_ADR1"),
+ MA35_MUX(0xb, "TM0_EXT"),
+ MA35_MUX(0xc, "ECAP1_IC1")),
+ MA35_PIN(124, PI2, 0xc0, 0x8,
+ MA35_MUX(0x0, "GPI2"),
+ MA35_MUX(0x1, "EPWM0_CH2"),
+ MA35_MUX(0x2, "UART12_RXD"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x5, "SPI3_MOSI"),
+ MA35_MUX(0x7, "SC0_DAT"),
+ MA35_MUX(0x8, "EBI_ADR2"),
+ MA35_MUX(0xb, "TM1"),
+ MA35_MUX(0xc, "ECAP1_IC2")),
+ MA35_PIN(125, PI3, 0xc0, 0xc,
+ MA35_MUX(0x0, "GPI3"),
+ MA35_MUX(0x1, "EPWM0_CH3"),
+ MA35_MUX(0x2, "UART12_TXD"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x5, "SPI3_MISO"),
+ MA35_MUX(0x7, "SC0_RST"),
+ MA35_MUX(0x8, "EBI_ADR3"),
+ MA35_MUX(0xb, "TM1_EXT")),
+ MA35_PIN(126, PI4, 0xc0, 0x10,
+ MA35_MUX(0x0, "GPI4"),
+ MA35_MUX(0x1, "EPWM0_CH4"),
+ MA35_MUX(0x2, "UART14_nCTS"),
+ MA35_MUX(0x3, "UART13_RXD"),
+ MA35_MUX(0x4, "I2C3_SDA"),
+ MA35_MUX(0x5, "SPI2_SS1"),
+ MA35_MUX(0x6, "I2S1_LRCK"),
+ MA35_MUX(0x8, "EBI_ADR4"),
+ MA35_MUX(0xd, "INT0")),
+ MA35_PIN(127, PI5, 0xc0, 0x14,
+ MA35_MUX(0x0, "GPI5"),
+ MA35_MUX(0x1, "EPWM0_CH5"),
+ MA35_MUX(0x2, "UART14_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x4, "I2C3_SCL"),
+ MA35_MUX(0x6, "I2S1_BCLK"),
+ MA35_MUX(0x8, "EBI_ADR5"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(128, PI6, 0xc0, 0x18,
+ MA35_MUX(0x0, "GPI6"),
+ MA35_MUX(0x1, "EPWM0_BRAKE0"),
+ MA35_MUX(0x2, "UART14_RXD"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x6, "I2S1_DI"),
+ MA35_MUX(0x8, "EBI_ADR6"),
+ MA35_MUX(0xc, "QEI1_INDEX"),
+ MA35_MUX(0xd, "INT2")),
+ MA35_PIN(129, PI7, 0xc0, 0x1c,
+ MA35_MUX(0x0, "GPI7"),
+ MA35_MUX(0x1, "EPWM0_BRAKE1"),
+ MA35_MUX(0x2, "UART14_TXD"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x6, "I2S1_DO"),
+ MA35_MUX(0x8, "EBI_ADR7"),
+ MA35_MUX(0xc, "ECAP0_IC0"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(130, PI8, 0xc4, 0x0,
+ MA35_MUX(0x0, "GPI8"),
+ MA35_MUX(0x2, "UART4_nCTS"),
+ MA35_MUX(0x3, "UART3_RXD"),
+ MA35_MUX(0x6, "LCM_DATA0"),
+ MA35_MUX(0xc, "EBI_AD11")),
+ MA35_PIN(131, PI9, 0xc4, 0x4,
+ MA35_MUX(0x0, "GPI9"),
+ MA35_MUX(0x2, "UART4_nRTS"),
+ MA35_MUX(0x3, "UART3_TXD"),
+ MA35_MUX(0x6, "LCM_DATA1"),
+ MA35_MUX(0xc, "EBI_AD12")),
+ MA35_PIN(132, PI10, 0xc4, 0x8,
+ MA35_MUX(0x0, "GPI10"),
+ MA35_MUX(0x2, "UART4_RXD"),
+ MA35_MUX(0x6, "LCM_DATA2"),
+ MA35_MUX(0xc, "EBI_AD13")),
+ MA35_PIN(133, PI11, 0xC4, 0xc,
+ MA35_MUX(0x0, "GPI11"),
+ MA35_MUX(0x2, "UART4_TXD"),
+ MA35_MUX(0x6, "LCM_DATA3"),
+ MA35_MUX(0xc, "EBI_AD14")),
+ MA35_PIN(134, PI12, 0xc4, 0x10,
+ MA35_MUX(0x0, "GPI12"),
+ MA35_MUX(0x2, "UART6_nCTS"),
+ MA35_MUX(0x3, "UART5_RXD"),
+ MA35_MUX(0x6, "LCM_DATA4")),
+ MA35_PIN(135, PI13, 0xc4, 0x14,
+ MA35_MUX(0x0, "GPI13"),
+ MA35_MUX(0x2, "UART6_nRTS"),
+ MA35_MUX(0x3, "UART5_TXD"),
+ MA35_MUX(0x6, "LCM_DATA5")),
+ MA35_PIN(136, PI14, 0xc4, 0x18,
+ MA35_MUX(0x0, "GPI14"),
+ MA35_MUX(0x2, "UART6_RXD"),
+ MA35_MUX(0x6, "LCM_DATA6")),
+ MA35_PIN(137, PI15, 0xc4, 0x1c,
+ MA35_MUX(0x0, "GPI15"),
+ MA35_MUX(0x2, "UART6_TXD"),
+ MA35_MUX(0x6, "LCM_DATA7")),
+ MA35_PIN(138, PJ0, 0xc8, 0x0,
+ MA35_MUX(0x0, "GPJ0"),
+ MA35_MUX(0x1, "EPWM1_BRAKE0"),
+ MA35_MUX(0x2, "UART8_nCTS"),
+ MA35_MUX(0x3, "UART7_RXD"),
+ MA35_MUX(0x4, "I2C2_SDA"),
+ MA35_MUX(0x5, "SPI2_SS0"),
+ MA35_MUX(0x6, "eMMC1_DAT4"),
+ MA35_MUX(0x7, "I2S0_LRCK"),
+ MA35_MUX(0x8, "SC0_CLK"),
+ MA35_MUX(0x9, "EBI_AD11"),
+ MA35_MUX(0xa, "EBI_ADR16"),
+ MA35_MUX(0xb, "EBI_nCS0"),
+ MA35_MUX(0xc, "EBI_AD7")),
+ MA35_PIN(139, PJ1, 0xc8, 0x4,
+ MA35_MUX(0x0, "GPJ1"),
+ MA35_MUX(0x1, "EPWM1_BRAKE1"),
+ MA35_MUX(0x2, "UART8_nRTS"),
+ MA35_MUX(0x3, "UART7_TXD"),
+ MA35_MUX(0x4, "I2C2_SCL"),
+ MA35_MUX(0x5, "SPI2_CLK"),
+ MA35_MUX(0x6, "eMMC1_DAT5"),
+ MA35_MUX(0x7, "I2S0_BCLK"),
+ MA35_MUX(0x8, "SC0_DAT"),
+ MA35_MUX(0x9, "EBI_AD12"),
+ MA35_MUX(0xa, "EBI_ADR17"),
+ MA35_MUX(0xb, "EBI_nCS1"),
+ MA35_MUX(0xc, "EBI_AD8")),
+ MA35_PIN(140, PJ2, 0xc8, 0x8,
+ MA35_MUX(0x0, "GPJ2"),
+ MA35_MUX(0x1, "EPWM1_CH4"),
+ MA35_MUX(0x2, "UART8_RXD"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x5, "SPI2_MOSI"),
+ MA35_MUX(0x6, "eMMC1_DAT6"),
+ MA35_MUX(0x7, "I2S0_DI"),
+ MA35_MUX(0x8, "SC0_RST"),
+ MA35_MUX(0x9, "EBI_AD13"),
+ MA35_MUX(0xa, "EBI_ADR18"),
+ MA35_MUX(0xb, "EBI_nWRH"),
+ MA35_MUX(0xc, "EBI_AD9")),
+ MA35_PIN(141, PJ3, 0xc8, 0xc,
+ MA35_MUX(0x0, "GPJ3"),
+ MA35_MUX(0x1, "EPWM1_CH5"),
+ MA35_MUX(0x2, "UART8_TXD"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x5, "SPI2_MISO"),
+ MA35_MUX(0x6, "eMMC1_DAT7"),
+ MA35_MUX(0x7, "I2S0_DO"),
+ MA35_MUX(0x8, "SC0_PWR"),
+ MA35_MUX(0x9, "EBI_AD14"),
+ MA35_MUX(0xa, "EBI_ADR19"),
+ MA35_MUX(0xb, "EBI_nWRL"),
+ MA35_MUX(0xc, "EBI_AD10")),
+ MA35_PIN(142, PJ4, 0xc8, 0x10,
+ MA35_MUX(0x0, "GPJ4"),
+ MA35_MUX(0x4, "I2C3_SDA"),
+ MA35_MUX(0x6, "SD1_WP")),
+ MA35_PIN(143, PJ5, 0xc8, 0x14,
+ MA35_MUX(0x0, "GPJ5"),
+ MA35_MUX(0x4, "I2C3_SCL"),
+ MA35_MUX(0x6, "SD1_nCD")),
+ MA35_PIN(144, PJ6, 0xc8, 0x18,
+ MA35_MUX(0x0, "GPJ6"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x6, "SD1_CMD/eMMC1_CMD")),
+ MA35_PIN(145, PJ7, 0xc8, 0x1c,
+ MA35_MUX(0x0, "GPJ7"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x6, "SD1_CLK/eMMC1_CLK")),
+ MA35_PIN(146, PJ8, 0xcc, 0x0,
+ MA35_MUX(0x0, "GPJ8"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x6, "SD1_DAT0/eMMC1_DAT0")),
+ MA35_PIN(147, PJ9, 0xcc, 0x4,
+ MA35_MUX(0x0, "GPJ9"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x6, "SD1_DAT1/eMMC1_DAT1")),
+ MA35_PIN(148, PJ10, 0xcc, 0x8,
+ MA35_MUX(0x0, "GPJ10"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x6, "SD1_DAT2/eMMC1_DAT2")),
+ MA35_PIN(149, PJ11, 0xcc, 0xc,
+ MA35_MUX(0x0, "GPJ11"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x6, "SD1_DAT3/eMMC1_DAT3")),
+ MA35_PIN(150, PJ12, 0xcc, 0x10,
+ MA35_MUX(0x0, "GPJ12"),
+ MA35_MUX(0x1, "EPWM1_CH2"),
+ MA35_MUX(0x2, "UART2_nCTS"),
+ MA35_MUX(0x3, "UART1_RXD"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x5, "SPI3_SS0"),
+ MA35_MUX(0x7, "SC1_CLK"),
+ MA35_MUX(0x8, "EBI_ADR12"),
+ MA35_MUX(0xb, "TM2"),
+ MA35_MUX(0xc, "QEI0_INDEX")),
+ MA35_PIN(151, PJ13, 0xcc, 0x14,
+ MA35_MUX(0x0, "GPJ13"),
+ MA35_MUX(0x1, "EPWM1_CH3"),
+ MA35_MUX(0x2, "UART2_nRTS"),
+ MA35_MUX(0x3, "UART1_TXD"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x5, "SPI3_MOSI"),
+ MA35_MUX(0x7, "SC1_DAT"),
+ MA35_MUX(0x8, "EBI_ADR13"),
+ MA35_MUX(0xb, "TM2_EXT")),
+ MA35_PIN(152, PJ14, 0xcc, 0x18,
+ MA35_MUX(0x0, "GPJ14"),
+ MA35_MUX(0x1, "EPWM1_CH4"),
+ MA35_MUX(0x2, "UART2_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "SPI3_MISO"),
+ MA35_MUX(0x7, "SC1_RST"),
+ MA35_MUX(0x8, "EBI_ADR14"),
+ MA35_MUX(0xb, "TM3")),
+ MA35_PIN(153, PJ15, 0xcc, 0x1c,
+ MA35_MUX(0x0, "GPJ15"),
+ MA35_MUX(0x1, "EPWM1_CH5"),
+ MA35_MUX(0x2, "UART2_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "SPI3_CLK"),
+ MA35_MUX(0x6, "EADC0_ST"),
+ MA35_MUX(0x7, "SC1_PWR"),
+ MA35_MUX(0x8, "EBI_ADR15"),
+ MA35_MUX(0xb, "TM3_EXT"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(154, PK0, 0xd0, 0x0,
+ MA35_MUX(0x0, "GPK0"),
+ MA35_MUX(0x1, "EPWM0_SYNC_IN"),
+ MA35_MUX(0x2, "UART16_nCTS"),
+ MA35_MUX(0x3, "UART15_RXD"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x6, "I2S1_MCLK"),
+ MA35_MUX(0x8, "EBI_ADR8"),
+ MA35_MUX(0xb, "TM7"),
+ MA35_MUX(0xc, "ECAP0_IC1")),
+ MA35_PIN(155, PK1, 0xd0, 0x4,
+ MA35_MUX(0x0, "GPK1"),
+ MA35_MUX(0x1, "EPWM0_SYNC_OUT"),
+ MA35_MUX(0x2, "UART16_nRTS"),
+ MA35_MUX(0x3, "UART15_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x6, "EADC0_ST"),
+ MA35_MUX(0x8, "EBI_ADR9"),
+ MA35_MUX(0xb, "TM7_EXT"),
+ MA35_MUX(0xc, "ECAP0_IC2")),
+ MA35_PIN(156, PK2, 0xd0, 0x8,
+ MA35_MUX(0x0, "GPK2"),
+ MA35_MUX(0x1, "EPWM1_CH0"),
+ MA35_MUX(0x2, "UART16_RXD"),
+ MA35_MUX(0x3, "CAN2_RXD"),
+ MA35_MUX(0x5, "SPI3_I2SMCLK"),
+ MA35_MUX(0x7, "SC0_PWR"),
+ MA35_MUX(0x8, "EBI_ADR10"),
+ MA35_MUX(0xc, "QEI0_A")),
+ MA35_PIN(157, PK3, 0xd0, 0xc,
+ MA35_MUX(0x0, "GPK3"),
+ MA35_MUX(0x1, "EPWM1_CH1"),
+ MA35_MUX(0x2, "UART16_TXD"),
+ MA35_MUX(0x3, "CAN2_TXD"),
+ MA35_MUX(0x5, "SPI3_SS1"),
+ MA35_MUX(0x7, "SC1_nCD"),
+ MA35_MUX(0x8, "EBI_ADR11"),
+ MA35_MUX(0xc, "QEI0_B")),
+ MA35_PIN(158, PK4, 0xd0, 0x10,
+ MA35_MUX(0x0, "GPK4"),
+ MA35_MUX(0x2, "UART12_nCTS"),
+ MA35_MUX(0x3, "UART13_RXD"),
+ MA35_MUX(0x5, "SPI2_MISO"),
+ MA35_MUX(0x6, "LCM_DEN"),
+ MA35_MUX(0xc, "EBI_AD10"),
+ MA35_MUX(0xd, "EBI_nWRL")),
+ MA35_PIN(159, PK5, 0xd0, 0x14,
+ MA35_MUX(0x0, "GPK5"),
+ MA35_MUX(0x1, "EPWM1_CH1"),
+ MA35_MUX(0x2, "UART12_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x5, "SPI2_CLK"),
+ MA35_MUX(0x7, "I2S1_DI"),
+ MA35_MUX(0x8, "SC0_DAT"),
+ MA35_MUX(0x9, "EADC0_ST"),
+ MA35_MUX(0xb, "TM8_EXT"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(160, PK6, 0xd0, 0x18,
+ MA35_MUX(0x0, "GPK6"),
+ MA35_MUX(0x1, "EPWM1_CH2"),
+ MA35_MUX(0x2, "UART12_RXD"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x5, "SPI2_MOSI"),
+ MA35_MUX(0x7, "I2S1_BCLK"),
+ MA35_MUX(0x8, "SC0_RST"),
+ MA35_MUX(0xb, "TM6"),
+ MA35_MUX(0xd, "INT2")),
+ MA35_PIN(161, PK7, 0xd0, 0x1c,
+ MA35_MUX(0x0, "GPK7"),
+ MA35_MUX(0x1, "EPWM1_CH3"),
+ MA35_MUX(0x2, "UART12_TXD"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x5, "SPI2_MISO"),
+ MA35_MUX(0x7, "I2S1_LRCK"),
+ MA35_MUX(0x8, "SC0_PWR"),
+ MA35_MUX(0x9, "CLKO"),
+ MA35_MUX(0xb, "TM6_EXT"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(162, PK8, 0xd4, 0x0,
+ MA35_MUX(0x0, "GPK8"),
+ MA35_MUX(0x1, "EPWM1_CH0"),
+ MA35_MUX(0x4, "I2C3_SDA"),
+ MA35_MUX(0x5, "SPI3_CLK"),
+ MA35_MUX(0x7, "EADC0_ST"),
+ MA35_MUX(0x8, "EBI_AD15"),
+ MA35_MUX(0x9, "EBI_MCLK"),
+ MA35_MUX(0xa, "EBI_ADR15"),
+ MA35_MUX(0xb, "TM8"),
+ MA35_MUX(0xc, "QEI1_INDEX")),
+ MA35_PIN(163, PK9, 0xd4, 0x4,
+ MA35_MUX(0x0, "GPK9"),
+ MA35_MUX(0x4, "I2C3_SCL"),
+ MA35_MUX(0x6, "CCAP0_SCLK"),
+ MA35_MUX(0x8, "EBI_AD0"),
+ MA35_MUX(0xa, "EBI_ADR0")),
+ MA35_PIN(164, PK10, 0xd4, 0x8,
+ MA35_MUX(0x0, "GPK10"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x6, "CCAP0_PIXCLK"),
+ MA35_MUX(0x8, "EBI_AD1"),
+ MA35_MUX(0xa, "EBI_ADR1")),
+ MA35_PIN(165, PK11, 0xd4, 0xc,
+ MA35_MUX(0x0, "GPK11"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x6, "CCAP0_HSYNC"),
+ MA35_MUX(0x8, "EBI_AD2"),
+ MA35_MUX(0xa, "EBI_ADR2")),
+ MA35_PIN(166, PK12, 0xd4, 0x10,
+ MA35_MUX(0x0, "GPK12"),
+ MA35_MUX(0x1, "EPWM2_CH0"),
+ MA35_MUX(0x2, "UART1_nCTS"),
+ MA35_MUX(0x3, "UART13_RXD"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x5, "I2S0_LRCK"),
+ MA35_MUX(0x6, "SPI1_SS0"),
+ MA35_MUX(0x8, "SC0_CLK"),
+ MA35_MUX(0xb, "TM10"),
+ MA35_MUX(0xd, "INT2")),
+ MA35_PIN(167, PK13, 0xd4, 0x14,
+ MA35_MUX(0x0, "GPK13"),
+ MA35_MUX(0x1, "EPWM2_CH1"),
+ MA35_MUX(0x2, "UART1_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x5, "I2S0_BCLK"),
+ MA35_MUX(0x6, "SPI1_CLK"),
+ MA35_MUX(0x8, "SC0_DAT"),
+ MA35_MUX(0xb, "TM10_EXT")),
+ MA35_PIN(168, PK14, 0xd4, 0x18,
+ MA35_MUX(0x0, "GPK14"),
+ MA35_MUX(0x1, "EPWM2_CH2"),
+ MA35_MUX(0x2, "UART1_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "I2S0_DI"),
+ MA35_MUX(0x6, "SPI1_MOSI"),
+ MA35_MUX(0x8, "SC0_RST"),
+ MA35_MUX(0xa, "I2C5_SDA"),
+ MA35_MUX(0xb, "TM11"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(169, PK15, 0xd4, 0x1c,
+ MA35_MUX(0x0, "GPK15"),
+ MA35_MUX(0x1, "EPWM2_CH3"),
+ MA35_MUX(0x2, "UART1_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "I2S0_DO"),
+ MA35_MUX(0x6, "SPI1_MISO"),
+ MA35_MUX(0x8, "SC0_PWR"),
+ MA35_MUX(0xa, "I2C5_SCL"),
+ MA35_MUX(0xb, "TM11_EXT")),
+ MA35_PIN(170, PL0, 0xd8, 0x0,
+ MA35_MUX(0x0, "GPL0"),
+ MA35_MUX(0x1, "EPWM1_CH0"),
+ MA35_MUX(0x2, "UART11_nCTS"),
+ MA35_MUX(0x3, "UART10_RXD"),
+ MA35_MUX(0x4, "I2C3_SDA"),
+ MA35_MUX(0x5, "SPI2_MOSI"),
+ MA35_MUX(0x6, "QSPI1_MOSI1"),
+ MA35_MUX(0x7, "I2S0_LRCK"),
+ MA35_MUX(0x8, "EBI_AD11"),
+ MA35_MUX(0x9, "SC1_CLK"),
+ MA35_MUX(0xb, "TM5"),
+ MA35_MUX(0xc, "QEI1_A")),
+ MA35_PIN(171, PL1, 0xd8, 0x4,
+ MA35_MUX(0x0, "GPL1"),
+ MA35_MUX(0x1, "EPWM1_CH1"),
+ MA35_MUX(0x2, "UART11_nRTS"),
+ MA35_MUX(0x3, "UART10_TXD"),
+ MA35_MUX(0x4, "I2C3_SCL"),
+ MA35_MUX(0x5, "SPI2_MISO"),
+ MA35_MUX(0x6, "QSPI1_MISO1"),
+ MA35_MUX(0x7, "I2S0_BCLK"),
+ MA35_MUX(0x8, "EBI_AD12"),
+ MA35_MUX(0x9, "SC1_DAT"),
+ MA35_MUX(0xb, "TM5_EXT"),
+ MA35_MUX(0xc, "QEI1_B")),
+ MA35_PIN(172, PL2, 0xd8, 0x8,
+ MA35_MUX(0x0, "GPL2"),
+ MA35_MUX(0x1, "EPWM1_CH2"),
+ MA35_MUX(0x2, "UART11_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "SPI2_SS0"),
+ MA35_MUX(0x6, "QSPI1_SS1"),
+ MA35_MUX(0x7, "I2S0_DI"),
+ MA35_MUX(0x8, "EBI_AD13"),
+ MA35_MUX(0x9, "SC1_RST"),
+ MA35_MUX(0xb, "TM7"),
+ MA35_MUX(0xc, "QEI1_INDEX")),
+ MA35_PIN(173, PL3, 0xd8, 0xc,
+ MA35_MUX(0x0, "GPL3"),
+ MA35_MUX(0x1, "EPWM1_CH3"),
+ MA35_MUX(0x2, "UART11_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "SPI2_CLK"),
+ MA35_MUX(0x6, "QSPI1_CLK"),
+ MA35_MUX(0x7, "I2S0_DO"),
+ MA35_MUX(0x8, "EBI_AD14"),
+ MA35_MUX(0x9, "SC1_PWR"),
+ MA35_MUX(0xb, "TM7_EXT"),
+ MA35_MUX(0xc, "ECAP0_IC0")),
+ MA35_PIN(174, PL4, 0xd8, 0x10,
+ MA35_MUX(0x0, "GPL4"),
+ MA35_MUX(0x1, "EPWM1_CH4"),
+ MA35_MUX(0x2, "UART2_nCTS"),
+ MA35_MUX(0x3, "UART1_RXD"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x5, "SPI3_MOSI"),
+ MA35_MUX(0x6, "QSPI1_MOSI0"),
+ MA35_MUX(0x7, "I2S0_MCLK"),
+ MA35_MUX(0x8, "EBI_nRD"),
+ MA35_MUX(0x9, "SC1_nCD"),
+ MA35_MUX(0xb, "TM9"),
+ MA35_MUX(0xc, "ECAP0_IC1")),
+ MA35_PIN(175, PL5, 0xd8, 0x14,
+ MA35_MUX(0x0, "GPL5"),
+ MA35_MUX(0x1, "EPWM1_CH5"),
+ MA35_MUX(0x2, "UART2_nRTS"),
+ MA35_MUX(0x3, "UART1_TXD"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x5, "SPI3_MISO"),
+ MA35_MUX(0x6, "QSPI1_MISO0"),
+ MA35_MUX(0x7, "I2S1_MCLK"),
+ MA35_MUX(0x8, "EBI_nWR"),
+ MA35_MUX(0x9, "SC0_nCD"),
+ MA35_MUX(0xb, "TM9_EXT"),
+ MA35_MUX(0xc, "ECAP0_IC2")),
+ MA35_PIN(176, PL6, 0xd8, 0x18,
+ MA35_MUX(0x0, "GPL6"),
+ MA35_MUX(0x1, "EPWM0_CH0"),
+ MA35_MUX(0x2, "UART2_RXD"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x6, "QSPI1_MOSI1"),
+ MA35_MUX(0x7, "TRACE_CLK"),
+ MA35_MUX(0x8, "EBI_AD5"),
+ MA35_MUX(0xb, "TM3"),
+ MA35_MUX(0xc, "ECAP1_IC0"),
+ MA35_MUX(0xd, "INT0")),
+ MA35_PIN(177, PL7, 0xd8, 0x1c,
+ MA35_MUX(0x0, "GPL7"),
+ MA35_MUX(0x1, "EPWM0_CH1"),
+ MA35_MUX(0x2, "UART2_TXD"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x6, "QSPI1_MISO1"),
+ MA35_MUX(0x8, "EBI_AD6"),
+ MA35_MUX(0xb, "TM3_EXT"),
+ MA35_MUX(0xc, "ECAP1_IC1"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(178, PL8, 0xdc, 0x0,
+ MA35_MUX(0x0, "GPL8"),
+ MA35_MUX(0x1, "EPWM0_CH2"),
+ MA35_MUX(0x2, "UART14_nCTS"),
+ MA35_MUX(0x3, "UART13_RXD"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x5, "SPI3_SS0"),
+ MA35_MUX(0x6, "EPWM0_CH4"),
+ MA35_MUX(0x7, "I2S1_LRCK"),
+ MA35_MUX(0x8, "EBI_AD7"),
+ MA35_MUX(0x9, "SC0_CLK"),
+ MA35_MUX(0xb, "TM4"),
+ MA35_MUX(0xc, "ECAP1_IC2"),
+ MA35_MUX(0xd, "INT2")),
+ MA35_PIN(179, PL9, 0xdc, 0x4,
+ MA35_MUX(0x0, "GPL9"),
+ MA35_MUX(0x1, "EPWM0_CH3"),
+ MA35_MUX(0x2, "UART14_nRTS"),
+ MA35_MUX(0x3, "UART13_TXD"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x5, "SPI3_CLK"),
+ MA35_MUX(0x6, "EPWM1_CH4"),
+ MA35_MUX(0x7, "I2S1_BCLK"),
+ MA35_MUX(0x8, "EBI_AD8"),
+ MA35_MUX(0x9, "SC0_DAT"),
+ MA35_MUX(0xb, "TM4_EXT"),
+ MA35_MUX(0xc, "QEI0_A"),
+ MA35_MUX(0xd, "INT3")),
+ MA35_PIN(180, PL10, 0xdc, 0x8,
+ MA35_MUX(0x0, "GPL10"),
+ MA35_MUX(0x1, "EPWM0_CH4"),
+ MA35_MUX(0x2, "UART14_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "SPI3_MOSI"),
+ MA35_MUX(0x6, "EPWM0_CH5"),
+ MA35_MUX(0x7, "I2S1_DI"),
+ MA35_MUX(0x8, "EBI_AD9"),
+ MA35_MUX(0x9, "SC0_RST"),
+ MA35_MUX(0xb, "EBI_nWRH"),
+ MA35_MUX(0xc, "QEI0_B")),
+ MA35_PIN(181, PL11, 0xdc, 0xc,
+ MA35_MUX(0x0, "GPL11"),
+ MA35_MUX(0x1, "EPWM0_CH5"),
+ MA35_MUX(0x2, "UART14_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "SPI3_MISO"),
+ MA35_MUX(0x6, "EPWM1_CH5"),
+ MA35_MUX(0x7, "I2S1_DO"),
+ MA35_MUX(0x8, "EBI_AD10"),
+ MA35_MUX(0x9, "SC0_PWR"),
+ MA35_MUX(0xb, "EBI_nWRL"),
+ MA35_MUX(0xc, "QEI0_INDEX")),
+ MA35_PIN(182, PL12, 0xdc, 0x10,
+ MA35_MUX(0x0, "GPL12"),
+ MA35_MUX(0x1, "EPWM0_SYNC_IN"),
+ MA35_MUX(0x2, "UART7_nCTS"),
+ MA35_MUX(0x3, "ECAP1_IC0"),
+ MA35_MUX(0x4, "UART14_RXD"),
+ MA35_MUX(0x5, "SPI0_SS0"),
+ MA35_MUX(0x6, "I2S1_LRCK"),
+ MA35_MUX(0x7, "SC1_CLK"),
+ MA35_MUX(0x8, "EBI_AD0"),
+ MA35_MUX(0x9, "HSUSBH_PWREN"),
+ MA35_MUX(0xa, "I2C2_SDA"),
+ MA35_MUX(0xb, "TM0"),
+ MA35_MUX(0xc, "EPWM0_CH2"),
+ MA35_MUX(0xd, "EBI_AD11"),
+ MA35_MUX(0xe, "RGMII0_PPS"),
+ MA35_MUX(0xf, "RMII0_PPS")),
+ MA35_PIN(183, PL13, 0xdc, 0x14,
+ MA35_MUX(0x0, "GPL13"),
+ MA35_MUX(0x1, "EPWM0_SYNC_OUT"),
+ MA35_MUX(0x2, "UART7_nRTS"),
+ MA35_MUX(0x3, "ECAP1_IC1"),
+ MA35_MUX(0x4, "UART14_TXD"),
+ MA35_MUX(0x5, "SPI0_CLK"),
+ MA35_MUX(0x6, "I2S1_BCLK"),
+ MA35_MUX(0x7, "SC1_DAT"),
+ MA35_MUX(0x8, "EBI_AD1"),
+ MA35_MUX(0x9, "HSUSBH_OVC"),
+ MA35_MUX(0xa, "I2C2_SCL"),
+ MA35_MUX(0xb, "TM0_EXT"),
+ MA35_MUX(0xc, "EPWM0_CH3"),
+ MA35_MUX(0xd, "EBI_AD12"),
+ MA35_MUX(0xe, "RGMII1_PPS"),
+ MA35_MUX(0xf, "RMII1_PPS")),
+ MA35_PIN(184, PL14, 0xdc, 0x18,
+ MA35_MUX(0x0, "GPL14"),
+ MA35_MUX(0x1, "EPWM0_CH2"),
+ MA35_MUX(0x2, "UART7_RXD"),
+ MA35_MUX(0x4, "CAN1_RXD"),
+ MA35_MUX(0x5, "SPI0_MOSI"),
+ MA35_MUX(0x6, "I2S1_DI"),
+ MA35_MUX(0x7, "SC1_RST"),
+ MA35_MUX(0x8, "EBI_AD2"),
+ MA35_MUX(0xb, "TM2"),
+ MA35_MUX(0xc, "INT0"),
+ MA35_MUX(0xd, "EBI_AD13")),
+ MA35_PIN(185, PL15, 0xdc, 0x1c,
+ MA35_MUX(0x0, "GPL15"),
+ MA35_MUX(0x1, "EPWM0_CH1"),
+ MA35_MUX(0x2, "UART7_TXD"),
+ MA35_MUX(0x3, "TRACE_CLK"),
+ MA35_MUX(0x4, "CAN1_TXD"),
+ MA35_MUX(0x5, "SPI0_MISO"),
+ MA35_MUX(0x6, "I2S1_DO"),
+ MA35_MUX(0x7, "SC1_PWR"),
+ MA35_MUX(0x8, "EBI_AD3"),
+ MA35_MUX(0xb, "TM2_EXT"),
+ MA35_MUX(0xc, "INT2"),
+ MA35_MUX(0xd, "EBI_AD14")),
+ MA35_PIN(186, PM0, 0xe0, 0x0,
+ MA35_MUX(0x0, "GPM0"),
+ MA35_MUX(0x4, "I2C4_SDA"),
+ MA35_MUX(0x6, "CCAP0_VSYNC"),
+ MA35_MUX(0x8, "EBI_AD3"),
+ MA35_MUX(0xa, "EBI_ADR3")),
+ MA35_PIN(187, PM1, 0xe0, 0x4,
+ MA35_MUX(0x0, "GPM1"),
+ MA35_MUX(0x4, "I2C4_SCL"),
+ MA35_MUX(0x5, "SPI3_I2SMCLK"),
+ MA35_MUX(0x6, "CCAP0_SFIELD"),
+ MA35_MUX(0x8, "EBI_AD4"),
+ MA35_MUX(0xa, "EBI_ADR4")),
+ MA35_PIN(188, PM2, 0xe0, 0x8,
+ MA35_MUX(0x0, "GPM2"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x6, "CCAP0_DATA0"),
+ MA35_MUX(0x8, "EBI_AD5"),
+ MA35_MUX(0xa, "EBI_ADR5")),
+ MA35_PIN(189, PM3, 0xe0, 0xc,
+ MA35_MUX(0x0, "GPM3"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x6, "CCAP0_DATA1"),
+ MA35_MUX(0x8, "EBI_AD6"),
+ MA35_MUX(0xa, "EBI_ADR6")),
+ MA35_PIN(190, PM4, 0xe0, 0x10,
+ MA35_MUX(0x0, "GPM4"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x6, "CCAP0_DATA2"),
+ MA35_MUX(0x8, "EBI_AD7"),
+ MA35_MUX(0xa, "EBI_ADR7")),
+ MA35_PIN(191, PM5, 0xe0, 0x14,
+ MA35_MUX(0x0, "GPM5"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x6, "CCAP0_DATA3"),
+ MA35_MUX(0x8, "EBI_AD8"),
+ MA35_MUX(0xa, "EBI_ADR8")),
+ MA35_PIN(192, PM6, 0xe0, 0x18,
+ MA35_MUX(0x0, "GPM6"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x6, "CCAP0_DATA4"),
+ MA35_MUX(0x8, "EBI_AD9"),
+ MA35_MUX(0xa, "EBI_ADR9")),
+ MA35_PIN(193, PM7, 0xe0, 0x1c,
+ MA35_MUX(0x0, "GPM7"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x6, "CCAP0_DATA5"),
+ MA35_MUX(0x8, "EBI_AD10"),
+ MA35_MUX(0xa, "EBI_ADR10")),
+ MA35_PIN(194, PM8, 0xe4, 0x0,
+ MA35_MUX(0x0, "GPM8"),
+ MA35_MUX(0x4, "I2C0_SDA"),
+ MA35_MUX(0x6, "CCAP0_DATA6"),
+ MA35_MUX(0x8, "EBI_AD11"),
+ MA35_MUX(0xa, "EBI_ADR11")),
+ MA35_PIN(195, PM9, 0xe4, 0x4,
+ MA35_MUX(0x0, "GPM9"),
+ MA35_MUX(0x4, "I2C0_SCL"),
+ MA35_MUX(0x6, "CCAP0_DATA7"),
+ MA35_MUX(0x8, "EBI_AD12"),
+ MA35_MUX(0xa, "EBI_ADR12")),
+ MA35_PIN(196, PM10, 0xe4, 0x8,
+ MA35_MUX(0x0, "GPM10"),
+ MA35_MUX(0x1, "EPWM1_CH2"),
+ MA35_MUX(0x3, "CAN2_RXD"),
+ MA35_MUX(0x5, "SPI3_SS0"),
+ MA35_MUX(0x6, "CCAP0_DATA8"),
+ MA35_MUX(0x7, "SPI2_I2SMCLK"),
+ MA35_MUX(0x8, "EBI_AD13"),
+ MA35_MUX(0xa, "EBI_ADR13")),
+ MA35_PIN(197, PM11, 0xe4, 0xc,
+ MA35_MUX(0x0, "GPM11"),
+ MA35_MUX(0x1, "EPWM1_CH3"),
+ MA35_MUX(0x3, "CAN2_TXD"),
+ MA35_MUX(0x5, "SPI3_SS1"),
+ MA35_MUX(0x6, "CCAP0_DATA9"),
+ MA35_MUX(0x7, "SPI2_SS1"),
+ MA35_MUX(0x8, "EBI_AD14"),
+ MA35_MUX(0xa, "EBI_ADR14")),
+ MA35_PIN(198, PM12, 0xe4, 0x10,
+ MA35_MUX(0x0, "GPM12"),
+ MA35_MUX(0x1, "EPWM1_CH4"),
+ MA35_MUX(0x2, "UART10_nCTS"),
+ MA35_MUX(0x3, "TRACE_DATA0"),
+ MA35_MUX(0x4, "UART11_RXD"),
+ MA35_MUX(0x5, "I2C2_SDA"),
+ MA35_MUX(0x7, "SC1_nCD"),
+ MA35_MUX(0x8, "EBI_AD8"),
+ MA35_MUX(0x9, "I2S1_MCLK"),
+ MA35_MUX(0xb, "TM8")),
+ MA35_PIN(199, PM13, 0xe4, 0x14,
+ MA35_MUX(0x0, "GPM13"),
+ MA35_MUX(0x1, "EPWM1_CH5"),
+ MA35_MUX(0x2, "UART10_nRTS"),
+ MA35_MUX(0x3, "TRACE_DATA1"),
+ MA35_MUX(0x4, "UART11_TXD"),
+ MA35_MUX(0x5, "I2C2_SCL"),
+ MA35_MUX(0x8, "EBI_AD9"),
+ MA35_MUX(0x9, "ECAP1_IC0"),
+ MA35_MUX(0xb, "TM8_EXT")),
+ MA35_PIN(200, PM14, 0xe4, 0x18,
+ MA35_MUX(0x0, "GPM14"),
+ MA35_MUX(0x1, "EPWM1_BRAKE0"),
+ MA35_MUX(0x2, "UART10_RXD"),
+ MA35_MUX(0x3, "TRACE_DATA2"),
+ MA35_MUX(0x4, "CAN2_RXD"),
+ MA35_MUX(0x6, "I2C3_SDA"),
+ MA35_MUX(0x8, "EBI_AD10"),
+ MA35_MUX(0x9, "ECAP1_IC1"),
+ MA35_MUX(0xb, "TM10"),
+ MA35_MUX(0xd, "INT1")),
+ MA35_PIN(201, PM15, 0xe4, 0x1c,
+ MA35_MUX(0x0, "GPM15"),
+ MA35_MUX(0x1, "EPWM1_BRAKE1"),
+ MA35_MUX(0x2, "UART10_TXD"),
+ MA35_MUX(0x3, "TRACE_DATA3"),
+ MA35_MUX(0x4, "CAN2_TXD"),
+ MA35_MUX(0x6, "I2C3_SCL"),
+ MA35_MUX(0x8, "EBI_AD11"),
+ MA35_MUX(0x9, "ECAP1_IC2"),
+ MA35_MUX(0xb, "TM10_EXT"),
+ MA35_MUX(0xd, "INT2")),
+ MA35_PIN(202, PN0, 0xe8, 0x0,
+ MA35_MUX(0x0, "GPN0"),
+ MA35_MUX(0x4, "I2C2_SDA"),
+ MA35_MUX(0x6, "CCAP1_DATA0")),
+ MA35_PIN(203, PN1, 0xe8, 0x4,
+ MA35_MUX(0x0, "GPN1"),
+ MA35_MUX(0x4, "I2C2_SCL"),
+ MA35_MUX(0x6, "CCAP1_DATA1")),
+ MA35_PIN(204, PN2, 0xe8, 0x8,
+ MA35_MUX(0x0, "GPN2"),
+ MA35_MUX(0x3, "CAN0_RXD"),
+ MA35_MUX(0x6, "CCAP1_DATA2")),
+ MA35_PIN(205, PN3, 0xe8, 0xc,
+ MA35_MUX(0x0, "GPN3"),
+ MA35_MUX(0x3, "CAN0_TXD"),
+ MA35_MUX(0x6, "CCAP1_DATA3")),
+ MA35_PIN(206, PN4, 0xe8, 0x10,
+ MA35_MUX(0x0, "GPN4"),
+ MA35_MUX(0x4, "I2C1_SDA"),
+ MA35_MUX(0x6, "CCAP1_DATA4")),
+ MA35_PIN(207, PN5, 0xe8, 0x14,
+ MA35_MUX(0x0, "GPN5"),
+ MA35_MUX(0x4, "I2C1_SCL"),
+ MA35_MUX(0x6, "CCAP1_DATA5")),
+ MA35_PIN(208, PN6, 0xe8, 0x18,
+ MA35_MUX(0x0, "GPN6"),
+ MA35_MUX(0x3, "CAN1_RXD"),
+ MA35_MUX(0x6, "CCAP1_DATA6")),
+ MA35_PIN(209, PN7, 0xe8, 0x1c,
+ MA35_MUX(0x0, "GPN7"),
+ MA35_MUX(0x3, "CAN1_TXD"),
+ MA35_MUX(0x6, "CCAP1_DATA7")),
+ MA35_PIN(210, PN10, 0xec, 0x8,
+ MA35_MUX(0x0, "GPN10"),
+ MA35_MUX(0x3, "CAN2_RXD"),
+ MA35_MUX(0x6, "CCAP1_SCLK")),
+ MA35_PIN(211, PN11, 0xec, 0xc,
+ MA35_MUX(0x0, "GPN11"),
+ MA35_MUX(0x3, "CAN2_TXD"),
+ MA35_MUX(0x6, "CCAP1_PIXCLK")),
+ MA35_PIN(212, PN12, 0xec, 0x10,
+ MA35_MUX(0x0, "GPN12"),
+ MA35_MUX(0x2, "UART6_nCTS"),
+ MA35_MUX(0x3, "UART12_RXD"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x6, "CCAP1_HSYNC")),
+ MA35_PIN(213, PN13, 0xec, 0x14,
+ MA35_MUX(0x0, "GPN13"),
+ MA35_MUX(0x2, "UART6_nRTS"),
+ MA35_MUX(0x3, "UART12_TXD"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x6, "CCAP1_VSYNC")),
+ MA35_PIN(214, PN14, 0xec, 0x18,
+ MA35_MUX(0x0, "GPN14"),
+ MA35_MUX(0x2, "UART6_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x5, "SPI1_SS1"),
+ MA35_MUX(0x6, "CCAP1_SFIELD"),
+ MA35_MUX(0x7, "SPI1_I2SMCLK")),
+ MA35_PIN(215, PN15, 0xec, 0x1c,
+ MA35_MUX(0x0, "GPN15"),
+ MA35_MUX(0x1, "EPWM2_CH4"),
+ MA35_MUX(0x2, "UART6_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x5, "I2S0_MCLK"),
+ MA35_MUX(0x6, "SPI1_SS1"),
+ MA35_MUX(0x7, "SPI1_I2SMCLK"),
+ MA35_MUX(0x8, "SC0_nCD"),
+ MA35_MUX(0x9, "EADC0_ST"),
+ MA35_MUX(0xa, "CLKO"),
+ MA35_MUX(0xb, "TM6")),
+ MA35_PIN(216, PN8, 0xec, 0x0,
+ MA35_MUX(0x0, "GPN8"),
+ MA35_MUX(0x1, "EPWM2_CH4"),
+ MA35_MUX(0x4, "I2C0_SDA"),
+ MA35_MUX(0x5, "SPI2_I2SMCLK"),
+ MA35_MUX(0x6, "CCAP1_DATA8")),
+ MA35_PIN(217, PN9, 0xec, 0x4,
+ MA35_MUX(0x0, "GPN9"),
+ MA35_MUX(0x1, "EPWM2_CH5"),
+ MA35_MUX(0x4, "I2C0_SCL"),
+ MA35_MUX(0x5, "SPI1_I2SMCLK"),
+ MA35_MUX(0x6, "CCAP1_DATA9")),
+ MA35_PIN(218, PN10, 0xec, 0x8,
+ MA35_MUX(0x0, "GPN10"),
+ MA35_MUX(0x3, "CAN2_RXD"),
+ MA35_MUX(0x4, "USBHL2_DM"),
+ MA35_MUX(0x6, "CCAP1_SCLK")),
+ MA35_PIN(219, PN11, 0xec, 0xc,
+ MA35_MUX(0x0, "GPN11"),
+ MA35_MUX(0x3, "CAN2_TXD"),
+ MA35_MUX(0x4, "USBHL2_DP"),
+ MA35_MUX(0x6, "CCAP1_PIXCLK")),
+ MA35_PIN(220, PN12, 0xec, 0x10,
+ MA35_MUX(0x0, "GPN12"),
+ MA35_MUX(0x2, "UART6_nCTS"),
+ MA35_MUX(0x3, "UART12_RXD"),
+ MA35_MUX(0x4, "I2C5_SDA"),
+ MA35_MUX(0x6, "CCAP1_HSYNC")),
+ MA35_PIN(221, PN13, 0xec, 0x14,
+ MA35_MUX(0x0, "GPN13"),
+ MA35_MUX(0x2, "UART6_nRTS"),
+ MA35_MUX(0x3, "UART12_TXD"),
+ MA35_MUX(0x4, "I2C5_SCL"),
+ MA35_MUX(0x6, "CCAP1_VSYNC")),
+ MA35_PIN(222, PN14, 0xec, 0x18,
+ MA35_MUX(0x0, "GPN14"),
+ MA35_MUX(0x2, "UART6_RXD"),
+ MA35_MUX(0x3, "CAN3_RXD"),
+ MA35_MUX(0x4, "USBHL3_DM"),
+ MA35_MUX(0x5, "SPI1_SS1"),
+ MA35_MUX(0x6, "CCAP1_SFIELD"),
+ MA35_MUX(0x7, "SPI1_I2SMCLK")),
+ MA35_PIN(223, PN15, 0xec, 0x1c,
+ MA35_MUX(0x0, "GPN15"),
+ MA35_MUX(0x1, "EPWM2_CH4"),
+ MA35_MUX(0x2, "UART6_TXD"),
+ MA35_MUX(0x3, "CAN3_TXD"),
+ MA35_MUX(0x4, "USBHL3_DP"),
+ MA35_MUX(0x5, "I2S0_MCLK"),
+ MA35_MUX(0x6, "SPI1_SS1"),
+ MA35_MUX(0x7, "SPI1_I2SMCLK"),
+ MA35_MUX(0x8, "SC0_nCD"),
+ MA35_MUX(0x9, "EADC0_ST"),
+ MA35_MUX(0xa, "CLKO"),
+ MA35_MUX(0xb, "TM6")),
+};
+
+static int ma35d1_get_pin_num(int offset, int shift)
+{
+ return (offset - 0x80) * 2 + shift / 4;
+}
+
+static struct ma35_pinctrl_soc_info ma35d1_pinctrl_info = {
+ .pins = ma35d1_pins,
+ .npins = ARRAY_SIZE(ma35d1_pins),
+ .get_pin_num = ma35d1_get_pin_num,
+};
+
+static const struct dev_pm_ops ma35d1_pinctrl_pm_ops = {
+ SET_LATE_SYSTEM_SLEEP_PM_OPS(ma35_pinctrl_suspend, ma35_pinctrl_resume)
+};
+
+static int ma35d1_pinctrl_probe(struct platform_device *pdev)
+{
+ return ma35_pinctrl_probe(pdev, &ma35d1_pinctrl_info);
+}
+
+static const struct of_device_id ma35d1_pinctrl_of_match[] = {
+ { .compatible = "nuvoton,ma35d1-pinctrl", },
+ { },
+};
+
+static struct platform_driver ma35d1_pinctrl_driver = {
+ .probe = ma35d1_pinctrl_probe,
+ .driver = {
+ .name = "ma35d1-pinctrl",
+ .pm = &ma35d1_pinctrl_pm_ops,
+ .of_match_table = ma35d1_pinctrl_of_match,
+ },
+};
+
+static int __init ma35d1_pinctrl_init(void)
+{
+ return platform_driver_register(&ma35d1_pinctrl_driver);
+}
+arch_initcall(ma35d1_pinctrl_init);
+
+MODULE_AUTHOR("[email protected]");
+MODULE_DESCRIPTION("Nuvoton MA35D1 pinctrl driver");
+MODULE_LICENSE("GPL");
--
2.34.1
On Tue, Apr 09, 2024 at 09:56:36AM +0000, Jacky Huang wrote:
> From: Jacky Huang <[email protected]>
>
> Add documentation to describe nuvoton ma35d1 pin control and GPIO.
>
> Signed-off-by: Jacky Huang <[email protected]>
> Reviewed-by: Krzysztof Kozlowski <[email protected]>
> ---
> .../pinctrl/nuvoton,ma35d1-pinctrl.yaml | 163 ++++++++++++++++++
> 1 file changed, 163 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
> new file mode 100644
> index 000000000000..8b9ec263213f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
> @@ -0,0 +1,163 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/nuvoton,ma35d1-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Nuvoton MA35D1 pin control and GPIO
> +
> +maintainers:
> + - Shan-Chun Hung <[email protected]>
> + - Jacky Huang <[email protected]>
> +
> +allOf:
> + - $ref: pinctrl.yaml#
> +
> +properties:
> + compatible:
> + enum:
> + - nuvoton,ma35d1-pinctrl
> +
> + '#address-cells':
> + const: 1
> +
> + '#size-cells':
> + const: 1
> +
> + nuvoton,sys:
> + $ref: /schemas/types.yaml#/definitions/phandle
> + description:
> + phandle of the system-management node.
If these are the *only* registers to access the pinctrl functions, then
this binding should be a child node of the system-management node and
then you don't need this property.
And if the registers for pinctrl are a defined range, you should add a
'reg' property (even though Linux and regmap don't use it).
> +
> + ranges: true
This property makes no sense with the binding as-is. You don't have
any address to translate. Maybe with the above changes it will.
> +
> +patternProperties:
> + "^gpio@[0-9a-f]+$":
> + type: object
> + additionalProperties: false
> + properties:
> + gpio-controller: true
> +
> + '#gpio-cells':
> + const: 2
> +
> + reg:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 1
> +
> + interrupt-controller: true
> +
> + '#interrupt-cells':
> + const: 2
> +
> + interrupts:
> + description:
> + The interrupt outputs to sysirq.
> + maxItems: 1
> +
> + required:
> + - gpio-controller
> + - '#gpio-cells'
> + - reg
> + - clocks
> + - interrupt-controller
> + - '#interrupt-cells'
> + - interrupts
> +
> + "^pin-[a-z0-9]+$":
> + type: object
> + description:
> + A pinctrl node should contain at least one subnodes representing the
> + pinctrl groups available on the machine. Each subnode will list the
> + pins it needs, and how they should be configured, with regard to muxer
> + configuration, pullups, drive strength, input enable/disable and input
> + schmitt.
> +
> + $ref: pincfg-node.yaml#
> +
> + properties:
> + power-source:
> + description: |
> + Valid arguments are described as below:
> + 0: power supply of 1.8V
> + 1: power supply of 3.3V
> + enum: [0, 1]
> +
> + drive-strength-microamp:
> + oneOf:
> + - enum: [ 2900, 4400, 5800, 7300, 8600, 10100, 11500, 13000 ]
> + description: 1.8V I/O driving strength
> + - enum: [ 17100, 25600, 34100, 42800, 48000, 56000, 77000, 82000 ]
> + description: 3.3V I/O driving strength
> +
> + unevaluatedProperties: false
In the indented cases, it's preferred to put this before 'properties'.
> +
> + "-grp$":
> + type: object
> + description:
> + Pinctrl node's client devices use subnodes for desired pin configuration.
> + Client device subnodes use below standard properties.
Missing $ref to common properties and 'unevaluatedProperties'.
> + properties:
> + nuvoton,pins:
> + description:
> + Each entry consists of 4 parameters and represents the mux and config
> + setting for one pin.
> + $ref: /schemas/types.yaml#/definitions/uint32-matrix
> + minItems: 1
> + items:
> + items:
> + - minimum: 0
> + maximum: 13
> + description:
> + Pin bank.
> + - minimum: 0
> + maximum: 15
> + description:
> + Pin bank index.
> + - minimum: 0
> + maximum: 15
> + description:
> + Mux 0 means GPIO and mux 1 to 15 means the specific device function.
> +
> +required:
> + - compatible
> + - nuvoton,sys
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/gpio/gpio.h>
> + #include <dt-bindings/clock/nuvoton,ma35d1-clk.h>
> +
> + pinctrl@40040000 {
> + compatible = "nuvoton,ma35d1-pinctrl";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + nuvoton,sys = <&sys>;
> + ranges = <0 0x40040000 0xc00>;
> +
> + gpio@0 {
> + reg = <0x0 0x40>;
> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk GPA_GATE>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + uart-grp {
> + uart11-pins {
This is not what the schema says.
> + nuvoton,pins = <11 0 2>,
> + <11 1 2>,
> + <11 2 2>,
> + <11 3 2>;
> + bias-disable;
> + power-source = <1>;
> + };
> + };
Include a pin-* node in the example.
> + };
> --
> 2.34.1
>
Dear Rob,
Thanks for your review.
On 2024/4/10 上午 12:29, Rob Herring wrote:
> On Tue, Apr 09, 2024 at 09:56:36AM +0000, Jacky Huang wrote:
>> From: Jacky Huang <[email protected]>
>>
>> Add documentation to describe nuvoton ma35d1 pin control and GPIO.
>>
>> Signed-off-by: Jacky Huang <[email protected]>
>> Reviewed-by: Krzysztof Kozlowski <[email protected]>
>> ---
>> .../pinctrl/nuvoton,ma35d1-pinctrl.yaml | 163 ++++++++++++++++++
>> 1 file changed, 163 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
>> new file mode 100644
>> index 000000000000..8b9ec263213f
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
>> @@ -0,0 +1,163 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/pinctrl/nuvoton,ma35d1-pinctrl.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Nuvoton MA35D1 pin control and GPIO
>> +
>> +maintainers:
>> + - Shan-Chun Hung <[email protected]>
>> + - Jacky Huang <[email protected]>
>> +
>> +allOf:
>> + - $ref: pinctrl.yaml#
>> +
>> +properties:
>> + compatible:
>> + enum:
>> + - nuvoton,ma35d1-pinctrl
>> +
>> + '#address-cells':
>> + const: 1
>> +
>> + '#size-cells':
>> + const: 1
>> +
>> + nuvoton,sys:
>> + $ref: /schemas/types.yaml#/definitions/phandle
>> + description:
>> + phandle of the system-management node.
> If these are the *only* registers to access the pinctrl functions, then
> this binding should be a child node of the system-management node and
> then you don't need this property.
>
> And if the registers for pinctrl are a defined range, you should add a
> 'reg' property (even though Linux and regmap don't use it).
I will add a 'reg' property for this.
>> +
>> + ranges: true
> This property makes no sense with the binding as-is. You don't have
> any address to translate. Maybe with the above changes it will.
I will fix the
ranges = <0 0x40040000 0xc00>;
as
reg = <0 0x40040000 0xc00>;
ranges;
>> +
>> +patternProperties:
>> + "^gpio@[0-9a-f]+$":
>> + type: object
>> + additionalProperties: false
>> + properties:
>> + gpio-controller: true
>> +
>> + '#gpio-cells':
>> + const: 2
>> +
>> + reg:
>> + maxItems: 1
>> +
>> + clocks:
>> + maxItems: 1
>> +
>> + interrupt-controller: true
>> +
>> + '#interrupt-cells':
>> + const: 2
>> +
>> + interrupts:
>> + description:
>> + The interrupt outputs to sysirq.
>> + maxItems: 1
>> +
>> + required:
>> + - gpio-controller
>> + - '#gpio-cells'
>> + - reg
>> + - clocks
>> + - interrupt-controller
>> + - '#interrupt-cells'
>> + - interrupts
>> +
>> + "^pin-[a-z0-9]+$":
>> + type: object
>> + description:
>> + A pinctrl node should contain at least one subnodes representing the
>> + pinctrl groups available on the machine. Each subnode will list the
>> + pins it needs, and how they should be configured, with regard to muxer
>> + configuration, pullups, drive strength, input enable/disable and input
>> + schmitt.
>> +
>> + $ref: pincfg-node.yaml#
>> +
>> + properties:
>> + power-source:
>> + description: |
>> + Valid arguments are described as below:
>> + 0: power supply of 1.8V
>> + 1: power supply of 3.3V
>> + enum: [0, 1]
>> +
>> + drive-strength-microamp:
>> + oneOf:
>> + - enum: [ 2900, 4400, 5800, 7300, 8600, 10100, 11500, 13000 ]
>> + description: 1.8V I/O driving strength
>> + - enum: [ 17100, 25600, 34100, 42800, 48000, 56000, 77000, 82000 ]
>> + description: 3.3V I/O driving strength
>> +
>> + unevaluatedProperties: false
> In the indented cases, it's preferred to put this before 'properties'.
>
I will fix it.
>> +
>> + "-grp$":
>> + type: object
>> + description:
>> + Pinctrl node's client devices use subnodes for desired pin configuration.
>> + Client device subnodes use below standard properties.
> Missing $ref to common properties and 'unevaluatedProperties'.
I will fix it.
>> + properties:
>> + nuvoton,pins:
>> + description:
>> + Each entry consists of 4 parameters and represents the mux and config
>> + setting for one pin.
>> + $ref: /schemas/types.yaml#/definitions/uint32-matrix
>> + minItems: 1
>> + items:
>> + items:
>> + - minimum: 0
>> + maximum: 13
>> + description:
>> + Pin bank.
>> + - minimum: 0
>> + maximum: 15
>> + description:
>> + Pin bank index.
>> + - minimum: 0
>> + maximum: 15
>> + description:
>> + Mux 0 means GPIO and mux 1 to 15 means the specific device function.
>> +
>> +required:
>> + - compatible
>> + - nuvoton,sys
>> +
>> +additionalProperties: false
>> +
>> +examples:
>> + - |
>> + #include <dt-bindings/interrupt-controller/arm-gic.h>
>> + #include <dt-bindings/gpio/gpio.h>
>> + #include <dt-bindings/clock/nuvoton,ma35d1-clk.h>
>> +
>> + pinctrl@40040000 {
>> + compatible = "nuvoton,ma35d1-pinctrl";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + nuvoton,sys = <&sys>;
>> + ranges = <0 0x40040000 0xc00>;
>> +
>> + gpio@0 {
>> + reg = <0x0 0x40>;
>> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&clk GPA_GATE>;
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + };
>> +
>> + uart-grp {
>> + uart11-pins {
> This is not what the schema says.
>> + nuvoton,pins = <11 0 2>,
>> + <11 1 2>,
>> + <11 2 2>,
>> + <11 3 2>;
>> + bias-disable;
>> + power-source = <1>;
>> + };
>> + };
> Include a pin-* node in the example.
This is my mistake. "pin-*" was the naming convention used in previous
versions, which
has now been changed to "-pins". Additionally, its hierarchy should be
under "-grp".
I will make corrections for these two issues.
>> + };
>> --
>> 2.34.1
>>
Best Regards,
Jacky Huang
Tue, Apr 09, 2024 at 09:56:37AM +0000, Jacky Huang kirjoitti:
> From: Jacky Huang <[email protected]>
>
> Add common pinctrl and GPIO driver for Nuvoton MA35 series SoC, and
> add support for ma35d1 pinctrl.
..
> + * Copyright (C) 2023 Nuvoton Technology Corp.
Almos mid of 2024...
..
> +#include <linux/gpio/driver.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/of.h>
> +#include <linux/of_irq.h>
> +#include <linux/of_device.h>
> +#include <linux/of_address.h>
Do you really need all of these pf*.h?
Don't you miss other headers to be included (spoiler: a lot!)
> +#include <linux/pinctrl/pinconf.h>
> +#include <linux/pinctrl/pinctrl.h>
Move this group...
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
..to be here to show the relation to the pin control subsystem.
> +#include "../core.h"
> +#include "../pinconf.h"
> +#include "pinctrl-ma35.h"
..
> +#define MA35_GP_MODE_MASK_WIDTH 2
> +
> +#define MA35_GP_SLEWCTL_MASK_WIDTH 2
I looked at the code how you use these... Oh, please switch to FIELD_GET() /
FIELD_PREP() (don't forget to include bitfield.h)
..
> +struct ma35_pin_func {
> + const char *name;
> + const char **groups;
> + u32 ngroups;
> +};
NIH struct pinfunction.
You may still have a wrapper (as struct pingroup below most likely will be
embedded in your custom data type), see the pinctrl-intel.h examples.
..
> +struct ma35_pin_group {
> + const char *name;
> + unsigned int npins;
> + unsigned int *pins;
NIH struct pingroup.
> + struct ma35_pin_setting *settings;
> +};
..
> +struct ma35_pin_bank {
> + void __iomem *reg_base;
> + struct clk *clk;
> + int irq;
> + u8 nr_pins;
> + const char *name;
> + u8 bank_num;
Interleaved fields with such a different type may lead to waste of memory. Run
`pahole` and update the ordering in this struct accordingly.
> + bool valid;
> + struct device_node *np;
Can you keep it fwnode-based?
> + struct gpio_chip chip;
> + u32 irqtype;
> + u32 irqinten;
> + struct regmap *regmap;
> + struct device *dev;
> + spinlock_t lock;
No use in RT_PREEMPT?
> +};
..
> + new_map = devm_kcalloc(pctldev->dev, map_num, sizeof(*new_map), GFP_KERNEL);
> + if (!new_map)
> + return -ENOMEM;
> +
> + *map = new_map;
> + *num_maps = map_num;
> + /* create mux map */
> + parent = of_get_parent(np);
> + if (!parent) {
> + devm_kfree(pctldev->dev, new_map);
Huh?! Are you sure you know the scope of usage of devm_*()?
> + return -EINVAL;
> + }
> +
..
> + regval &= ~GENMASK(setting->shift + MA35_MFP_BITS_PER_PORT - 1,
> + setting->shift);
This will generate an awful code. Use respective FIELD_*() macros.
..
> + regval &= ~GENMASK(gpio * MA35_GP_MODE_MASK_WIDTH - 1,
> + gpio * MA35_GP_MODE_MASK_WIDTH);
> + regval |= mode << gpio * MA35_GP_MODE_MASK_WIDTH;
Ditto.
..
> + regval &= GENMASK(gpio * MA35_GP_MODE_MASK_WIDTH - 1,
> + gpio * MA35_GP_MODE_MASK_WIDTH);
> +
> + return regval >> gpio * MA35_GP_MODE_MASK_WIDTH;
Ditto.
..
> +static int ma35_gpio_core_direction_in(struct gpio_chip *gc, unsigned int gpio)
> +{
> + struct ma35_pin_bank *bank = gpiochip_get_data(gc);
> + void __iomem *reg_mode = bank->reg_base + MA35_GP_REG_MODE;
> + unsigned long flags;
> +
> + spin_lock_irqsave(&bank->lock, flags);
Use cleanup.h, i.e. guard() in this case, from day 1.
Similar approach for all other places.
> + spin_unlock_irqrestore(&bank->lock, flags);
> +
> + return 0;
> +}
..
> + regval = readl(reg_dout);
> + if (val)
> + writel(regval | BIT(gpio), reg_dout);
> + else
> + writel(regval & ~BIT(gpio), reg_dout);
Can you split regval update and make only a single writel() call? It's slightly
better pattern
read()
if (foo)
v =
else
v =
write()
> + ma35_gpio_set_mode(reg_mode, gpio, MA35_GP_MODE_OUTPUT);
..
> + regval &= ~GENMASK(bit_offs + MA35_MFP_BITS_PER_PORT - 1, bit_offs);
FIELD_GET()
..
> + writel(1<<num, reg_intsrc);
Oh, something happened here, besides indentation.
Have you meant BIT() ?
..
> + unsigned int num = (d->hwirq);
Read Documentation on how to access hwirq field and what type of the value
should be. There are plently of the examples already in the kernel. Just
check the recent (more or less) ones.
..
> + /*
> + * The MA35_GP_REG_INTEN bits 0 ~ 15 control low-level or falling edge trigger,
> + * while bits 16 ~ 31 control high-level or rising edge trigger.
> + * We disable both type of interrupt.
> + */
> + regval &= ~(BIT(num + 16) | BIT(num));
You have this idiom more than once in the code, make the definition and use it.
Move comment closer to that definition.
..
> + irq_set_handler_locked(d, handle_edge_irq);
> + bank->irqtype &= ~(0x1 << num);
> + bank->irqinten |= (0x1 << num);
> + bank->irqinten &= ~(0x1 << (num + 16));
> + break;
> + case IRQ_TYPE_LEVEL_HIGH:
> + irq_set_handler_locked(d, handle_level_irq);
> + bank->irqtype |= (0x1 << num);
> + bank->irqinten &= ~(0x1 << num);
> + bank->irqinten |= (0x1 << (num + 16));
> + break;
> + case IRQ_TYPE_LEVEL_LOW:
> + irq_set_handler_locked(d, handle_level_irq);
> + bank->irqtype |= (0x1 << num);
> + bank->irqinten &= ~(0x1 << (num + 16));
> + bank->irqinten |= (0x1 << num);
> + break;
BIT() in all cases.
..
> + irq_set_handler_locked(d, handle_bad_irq);
Just assign it in the probe.
..
> +static struct irq_chip ma35_gpio_irqchip = {
> + .name = "MA35-GPIO-IRQ",
> + .irq_disable = ma35_irq_gpio_mask,
> + .irq_enable = ma35_irq_gpio_unmask,
> + .irq_ack = ma35_irq_gpio_ack,
> + .irq_mask = ma35_irq_gpio_mask,
> + .irq_unmask = ma35_irq_gpio_unmask,
> + .irq_set_type = ma35_irq_irqtype,
> + .flags = IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_SKIP_SET_WAKE | IRQCHIP_IMMUTABLE,
It doesn't look like IMMUTABLE. Again, check other examples, there are a lot.
..
> +static void ma35_irq_demux_intgroup(struct irq_desc *desc)
> +{
> + struct ma35_pin_bank *bank = gpiochip_get_data(irq_desc_get_handler_data(desc));
> + struct irq_domain *irqdomain = bank->chip.irq.domain;
> + struct irq_chip *irqchip = irq_desc_get_chip(desc);
> + unsigned long isr;
> + int offset;
> +
> + chained_irq_enter(irqchip, desc);
> + isr = readl(bank->reg_base + MA35_GP_REG_INTSRC);
> + if (isr)
Unneeded duplicate check.
> + for_each_set_bit(offset, &isr, bank->nr_pins)
> + generic_handle_irq(irq_find_mapping(irqdomain, offset));
> +
> + chained_irq_exit(irqchip, desc);
> +}
..
> + for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
Why pre-increments?
> + if (!bank->valid) {
> + dev_warn(&pdev->dev, "bank %s is not valid\n",
> + bank->np->name);
Do not use fwnode / of_node name like this, use proper specifiers: %pfw / %pOF.
> + continue;
> + }
> + bank->irqtype = 0;
> + bank->irqinten = 0;
> + bank->chip.label = bank->name;
> + bank->chip.of_gpio_n_cells = 2;
> + bank->chip.parent = &pdev->dev;
> + bank->chip.request = ma35_gpio_core_to_request;
> + bank->chip.direction_input = ma35_gpio_core_direction_in;
> + bank->chip.direction_output = ma35_gpio_core_direction_out;
> + bank->chip.get = ma35_gpio_core_get;
> + bank->chip.set = ma35_gpio_core_set;
> + bank->chip.base = -1;
> + bank->chip.ngpio = bank->nr_pins;
> + bank->chip.can_sleep = false;
> + spin_lock_init(&bank->lock);
> +
> + if (bank->irq > 0) {
> + struct gpio_irq_chip *girq;
> +
> + girq = &bank->chip.irq;
> + gpio_irq_chip_set_chip(girq, &ma35_gpio_irqchip);
> + girq->parent_handler = ma35_irq_demux_intgroup;
> + girq->num_parents = 1;
> +
> + girq->parents = devm_kcalloc(&pdev->dev, 1, sizeof(*girq->parents),
Use num_parents instead of 1.
> + GFP_KERNEL);
> + if (!girq->parents) {
> + ret = -ENOMEM;
> + goto fail;
> + }
> +
> + girq->parents[0] = bank->irq;
> + girq->default_type = IRQ_TYPE_NONE;
> + girq->handler = handle_bad_irq;
> + }
> +
> + ret = gpiochip_add_data(&bank->chip, bank);
> + if (ret) {
> + dev_err(&pdev->dev, "failed to register gpio_chip %s, error code: %d\n",
> + bank->chip.label, ret);
> + goto fail;
> + }
> + }
..
> +fail:
> + for (--i, --bank; i >= 0; --i, --bank) {
while (i--) {
bank--;
...
}
much better to read.
> + if (!bank->valid)
> + continue;
> + gpiochip_remove(&bank->chip);
> + }
> + return ret;
> +}
..
> +static int ma35_get_bank_data(struct ma35_pin_bank *bank, struct ma35_pinctrl *npctl)
> +{
> + struct resource res;
> +
> + if (of_address_to_resource(bank->np, 0, &res)) {
> + dev_err(npctl->dev, "cannot find IO resource for bank\n");
> + return -ENOENT;
> + }
> +
> + bank->reg_base = devm_ioremap_resource(npctl->dev, &res);
> + if (IS_ERR(bank->reg_base)) {
> + dev_err(npctl->dev, "cannot ioremap resource for bank\n");
> + return PTR_ERR(bank->reg_base);
> + }
Use fwnode_iomap()
> + bank->irq = irq_of_parse_and_map(bank->np, 0);
Use fwnode_get_irq()
> + bank->nr_pins = MA35_GPIO_PORT_MAX;
> +
> + bank->clk = of_clk_get(bank->np, 0);
Can't you use simple clk_get()? Why?
> + if (IS_ERR(bank->clk))
> + return PTR_ERR(bank->clk);
> +
> + return clk_prepare_enable(bank->clk);
> +}
..
> + for_each_gpiochip_node(&pdev->dev, child) {
> + struct device_node *np = to_of_node(child);
No need, just keep everythin fwnode based.
> + bank = &ctrl->pin_banks[id];
> + bank->np = np;
> + bank->regmap = pctl->regmap;
> + bank->dev = &pdev->dev;
> + if (!ma35_get_bank_data(bank, pctl))
> + bank->valid = true;
> + id++;
> + }
..
> + regval &= ~GENMASK(port * MA35_GP_PUSEL_MASK_WIDTH - 1,
> + port * MA35_GP_PUSEL_MASK_WIDTH);
FIELD_*()
..
> + regval &= GENMASK(port * MA35_GP_PUSEL_MASK_WIDTH - 1,
> + port * MA35_GP_PUSEL_MASK_WIDTH);
> + regval >>= port * MA35_GP_PUSEL_MASK_WIDTH;
Ditto.
..
> + if (regval & BIT(port))
> + return MVOLT_3300;
> + else
> + return MVOLT_1800;
Can be written as
return (regval & BIT()) ? _3300 : _1800;
..
> + if (port < MA35_GP_DSH_BASE_PORT) {
> + regval = readl(base + MA35_GP_REG_DSL);
> + ds_val = (regval & GENMASK(port * 4 + 2, port * 4)) >> port * 4;
This is too complicated way of saying
ds_val = (regval >> port * 4) & GENMASK(2, 0);
> + } else {
> + port -= MA35_GP_DSH_BASE_PORT;
> + regval = readl(base + MA35_GP_REG_DSH);
> + ds_val = (regval & GENMASK(port * 4 + 2, port * 4)) >> port * 4;
Ditto.
> + }
..
> + if (ma35_pinconf_get_power_source(npctl, pin) == MVOLT_1800) {
> + for (i = 0; i < ARRAY_SIZE(ds_1800mv_tbl); i++) {
> + if (ds_1800mv_tbl[i] == strength)
> + ds_val = i;
And still continue?!
> + }
> + } else {
> + for (i = 0; i < ARRAY_SIZE(ds_3300mv_tbl); i++) {
> + if (ds_3300mv_tbl[i] == strength)
> + ds_val = i;
Ditto.
> + }
> + }
Wondering if the linear_ranges or other existing tables approaches can be used here.
..
> + if (port < MA35_GP_DSH_BASE_PORT) {
> + regval = readl(base + MA35_GP_REG_DSL);
> + regval &= ~GENMASK(port * 4 + 2, port * 4);
> + regval |= ds_val << port * 4;
As per above
~(GENMASK(2, 0) << (port * 4))
> + writel(regval, base + MA35_GP_REG_DSL);
> + } else {
> + port -= MA35_GP_DSH_BASE_PORT;
> + regval = readl(base + MA35_GP_REG_DSH);
> + regval &= ~GENMASK(port * 4 + 2, port * 4);
Ditto.
> + regval |= ds_val << port * 4;
> + writel(regval, base + MA35_GP_REG_DSH);
> + }
..
> + regval &= ~GENMASK(port * MA35_GP_SLEWCTL_MASK_WIDTH - 1,
> + port * MA35_GP_SLEWCTL_MASK_WIDTH);
> + regval |= rate << port * MA35_GP_SLEWCTL_MASK_WIDTH;
FIELD_*()
..
> +static int ma35_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin, unsigned long *config)
> +{
> + struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
> + enum pin_config_param param = pinconf_to_config_param(*config);
> + u32 arg;
> + int ret;
> +
> + switch (param) {
> + case PIN_CONFIG_BIAS_DISABLE:
> + case PIN_CONFIG_BIAS_PULL_DOWN:
> + case PIN_CONFIG_BIAS_PULL_UP:
> + if (ma35_pinconf_get_pull(npctl, pin) == param)
> + arg = 1;
> + else
> + return -EINVAL;
> + break;
Check for the error case first and get rid of redundant 'else'.
> + case PIN_CONFIG_DRIVE_STRENGTH:
> + ret = ma35_pinconf_get_drive_strength(npctl, pin, &arg);
> + if (ret)
> + return ret;
> + break;
> +
> + case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
> + arg = ma35_pinconf_get_schmitt_enable(npctl, pin);
> + break;
> +
> + case PIN_CONFIG_SLEW_RATE:
> + arg = ma35_pinconf_get_slew_rate(npctl, pin);
> + break;
> +
> + case PIN_CONFIG_OUTPUT_ENABLE:
> + arg = ma35_pinconf_get_output(npctl, pin);
> + break;
> +
> + case PIN_CONFIG_POWER_SOURCE:
> + arg = ma35_pinconf_get_power_source(npctl, pin);
> + break;
> +
> + default:
> + return -EINVAL;
> + }
> + *config = pinconf_to_config_packed(param, arg);
> +
> + return 0;
> +}
..
> +static int ma35_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
> + unsigned long *configs, unsigned int num_configs)
> +{
> + struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
> + enum pin_config_param param;
> + unsigned int arg = 0;
> + int i, ret = 0;
> +
> + for (i = 0; i < num_configs; i++) {
> + param = pinconf_to_config_param(configs[i]);
> + arg = pinconf_to_config_argument(configs[i]);
> +
> + switch (param) {
> + case PIN_CONFIG_BIAS_DISABLE:
> + case PIN_CONFIG_BIAS_PULL_UP:
> + case PIN_CONFIG_BIAS_PULL_DOWN:
> + ret = ma35_pinconf_set_pull(npctl, pin, param);
> + break;
> +
> + case PIN_CONFIG_DRIVE_STRENGTH:
> + ret = ma35_pinconf_set_drive_strength(npctl, pin, arg);
> + break;
> +
> + case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
> + ret = ma35_pinconf_set_schmitt(npctl, pin, 1);
> + break;
> +
> + case PIN_CONFIG_INPUT_SCHMITT:
> + ret = ma35_pinconf_set_schmitt(npctl, pin, arg);
> + break;
> +
> + case PIN_CONFIG_SLEW_RATE:
> + ret = ma35_pinconf_set_slew_rate(npctl, pin, arg);
> + break;
> +
> + case PIN_CONFIG_OUTPUT_ENABLE:
> + ret = ma35_pinconf_set_output(npctl, pin, arg);
> + break;
> +
> + case PIN_CONFIG_POWER_SOURCE:
> + ret = ma35_pinconf_set_power_source(npctl, pin, arg);
> + break;
> +
> + default:
> + return -EINVAL;
> + }
No returning an error if we got ret != 0?!
> + }
> + return ret;
> +}
..
> +static int ma35_pinctrl_parse_groups(struct device_node *np, struct ma35_pin_group *grp,
> + struct ma35_pinctrl *npctl, u32 index)
> +{
> + unsigned long *configs;
> + unsigned int nconfigs;
> + struct ma35_pin_setting *pin;
> + const __be32 *list;
Huh?!
> + int i, j, size, ret;
> +
> + dev_dbg(npctl->dev, "group(%d): %s\n", index, np->name);
> +
> + grp->name = np->name;
> +
> + ret = pinconf_generic_parse_dt_config(np, NULL, &configs, &nconfigs);
> + if (ret)
> + return ret;
> +
> + /*
> + * the binding format is nuvoton,pins = <bank pin-mfp pin-function>,
> + * do sanity check and calculate pins number
> + */
/*
* Respect English grammar and puntuation
* in all multi-line comments. See the difference
* how it's done above and in this example.
*/
> + list = of_get_property(np, "nuvoton,pins", &size);
Oh, no.
Use respective of_property_ calls.
> + size /= sizeof(*list);
> + if (!size || size % 3) {
> + dev_err(npctl->dev, "wrong setting!\n");
> + return -EINVAL;
> + }
> + grp->npins = size / 3;
> +
> + grp->pins = devm_kcalloc(npctl->dev, grp->npins, sizeof(*grp->pins), GFP_KERNEL);
> + if (!grp->pins)
> + return -ENOMEM;
> +
> + grp->settings = devm_kcalloc(npctl->dev, grp->npins, sizeof(*grp->settings), GFP_KERNEL);
> + if (!grp->settings)
> + return -ENOMEM;
> +
> + pin = grp->settings;
> +
> + for (i = 0, j = 0; i < size; i += 3, j++) {
> + pin->offset = be32_to_cpu(*list++) * MA35_MFP_REG_SZ_PER_BANK + MA35_MFP_REG_BASE;
> + pin->shift = (be32_to_cpu(*list++) * MA35_MFP_BITS_PER_PORT) % 32;
> + pin->muxval = be32_to_cpu(*list++);
> + pin->configs = configs;
> + pin->nconfigs = nconfigs;
> + grp->pins[j] = npctl->info->get_pin_num(pin->offset, pin->shift);
> + pin++;
> + }
> + return 0;
> +}
..
> + for_each_child_of_node(np, child) {
> + if (of_property_read_bool(child, "gpio-controller"))
> + continue;
There is a macro already present, for_each_gpiochip_node().
> + npctl->nfunctions++;
> + npctl->ngroups += of_get_child_count(child);
> + }
..
> + for_each_child_of_node(np, child) {
> + if (of_property_read_bool(child, "gpio-controller"))
> + continue;
Ditto.
> + ret = ma35_pinctrl_parse_functions(child, npctl, idx++);
> + if (ret) {
> + dev_err(&pdev->dev, "failed to parse function\n");
> + of_node_put(child);
> + return ret;
> + }
> + }
..
> + if (!info || !info->pins || !info->npins) {
> + dev_err(&pdev->dev, "wrong pinctrl info\n");
> + return -EINVAL;
return dev_err_probe(...);
> + }
..
> + ret = devm_pinctrl_register_and_init(&pdev->dev, ma35_pinctrl_desc,
> + npctl, &npctl->pctl);
Haveing
struct device *dev = &pdev->dev;
makes in particular this one better
ret = devm_pinctrl_register_and_init(dev, ma35_pinctrl_desc, npctl, &npctl->pctl);
> + if (ret)
> + return dev_err_probe(&pdev->dev, ret, "fail to register MA35 pinctrl\n");
..
> +int __maybe_unused ma35_pinctrl_suspend(struct device *dev)
No __maybe_unused.
Just use respective PM macros (pm_ptr(), DEFINE_,*PM_OPS, etc).
> +{
> + struct ma35_pinctrl *npctl = dev_get_drvdata(dev);
> +
> + return pinctrl_force_sleep(npctl->pctl);
> +}
> +
> +int __maybe_unused ma35_pinctrl_resume(struct device *dev)
Ditto.
> +{
> + struct ma35_pinctrl *npctl = dev_get_drvdata(dev);
> +
> + return pinctrl_force_default(npctl->pctl);
> +}
..
> +struct ma35_mux_desc {
> + const char *name;
> + u32 muxval;
> +};
> +
> +struct ma35_pin_data {
> + u32 offset;
> + u32 shift;
> + struct ma35_mux_desc *muxes;
> +};
Don't pin control subsystem has already some data types suitable in this cases?
..
> +#define MA35_PIN(num, n, o, s, ...) { \
> + .number = num, \
> + .name = #n, \
Don't we have macros for this?
> + .drv_data = &(struct ma35_pin_data) { \
> + .offset = o, \
> + .shift = s, \
> + .muxes = (struct ma35_mux_desc[]) { \
> + __VA_ARGS__, { } }, \
> + }, \
> +}
..
> +#include <linux/init.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
Missing headers and stray ones. Please, get this into order by following IWYU
principle.
> +#include <linux/of.h>
> +#include <linux/of_device.h>
How are these being used?
> +#include <linux/pinctrl/pinctrl.h>
..
> +static const struct dev_pm_ops ma35d1_pinctrl_pm_ops = {
> + SET_LATE_SYSTEM_SLEEP_PM_OPS(ma35_pinctrl_suspend, ma35_pinctrl_resume)
> +};
New PM macros, please.
..
> +static const struct of_device_id ma35d1_pinctrl_of_match[] = {
> + { .compatible = "nuvoton,ma35d1-pinctrl", },
> + { },
No comma in the terminator entry.
> +};
..
> +static struct platform_driver ma35d1_pinctrl_driver = {
> + .probe = ma35d1_pinctrl_probe,
> + .driver = {
> + .name = "ma35d1-pinctrl",
> + .pm = &ma35d1_pinctrl_pm_ops,
New PM macro here.
> + .of_match_table = ma35d1_pinctrl_of_match,
> + },
> +};
--
With Best Regards,
Andy Shevchenko
Dear Andy,
Sorry for the late response to your mail.
Due to email inbox policy issues, I just found this email.
Regarding your comments, I will make all the modifications in the next
version.
Thank you for your help.
Best Regards,
Jacky Huang
On 2024/4/10 下午 04:54, Andy Shevchenko wrote:
> CAUTION - External Email: Do not click links or open attachments unless you acknowledge the sender and content.
>
>
> Tue, Apr 09, 2024 at 09:56:37AM +0000, Jacky Huang kirjoitti:
>> From: Jacky Huang <[email protected]>
>>
>> Add common pinctrl and GPIO driver for Nuvoton MA35 series SoC, and
>> add support for ma35d1 pinctrl.
> ...
>
>> + * Copyright (C) 2023 Nuvoton Technology Corp.
> Almos mid of 2024...
>
> ...
>
>> +#include <linux/gpio/driver.h>
>> +#include <linux/mfd/syscon.h>
>> +#include <linux/of.h>
>> +#include <linux/of_irq.h>
>> +#include <linux/of_device.h>
>> +#include <linux/of_address.h>
> Do you really need all of these pf*.h?
> Don't you miss other headers to be included (spoiler: a lot!)
>
>> +#include <linux/pinctrl/pinconf.h>
>> +#include <linux/pinctrl/pinctrl.h>
> Move this group...
>
>> +#include <linux/platform_device.h>
>> +#include <linux/regmap.h>
>> +
> ...to be here to show the relation to the pin control subsystem.
>
>> +#include "../core.h"
>> +#include "../pinconf.h"
>> +#include "pinctrl-ma35.h"
> ...
>
>> +#define MA35_GP_MODE_MASK_WIDTH 2
>> +
>> +#define MA35_GP_SLEWCTL_MASK_WIDTH 2
> I looked at the code how you use these... Oh, please switch to FIELD_GET() /
> FIELD_PREP() (don't forget to include bitfield.h)
>
> ...
>
>> +struct ma35_pin_func {
>> + const char *name;
>> + const char **groups;
>> + u32 ngroups;
>> +};
> NIH struct pinfunction.
>
> You may still have a wrapper (as struct pingroup below most likely will be
> embedded in your custom data type), see the pinctrl-intel.h examples.
>
> ...
>
>> +struct ma35_pin_group {
>> + const char *name;
>> + unsigned int npins;
>> + unsigned int *pins;
> NIH struct pingroup.
>
>> + struct ma35_pin_setting *settings;
>> +};
> ...
>
>> +struct ma35_pin_bank {
>> + void __iomem *reg_base;
>> + struct clk *clk;
>> + int irq;
>> + u8 nr_pins;
>> + const char *name;
>> + u8 bank_num;
> Interleaved fields with such a different type may lead to waste of memory. Run
> `pahole` and update the ordering in this struct accordingly.
>
>> + bool valid;
>> + struct device_node *np;
> Can you keep it fwnode-based?
>
>> + struct gpio_chip chip;
>> + u32 irqtype;
>> + u32 irqinten;
>> + struct regmap *regmap;
>> + struct device *dev;
>> + spinlock_t lock;
> No use in RT_PREEMPT?
>
>> +};
> ...
>
>> + new_map = devm_kcalloc(pctldev->dev, map_num, sizeof(*new_map), GFP_KERNEL);
>> + if (!new_map)
>> + return -ENOMEM;
>> +
>> + *map = new_map;
>> + *num_maps = map_num;
>> + /* create mux map */
>> + parent = of_get_parent(np);
>> + if (!parent) {
>> + devm_kfree(pctldev->dev, new_map);
> Huh?! Are you sure you know the scope of usage of devm_*()?
>
>> + return -EINVAL;
>> + }
>> +
> ...
>
>> + regval &= ~GENMASK(setting->shift + MA35_MFP_BITS_PER_PORT - 1,
>> + setting->shift);
> This will generate an awful code. Use respective FIELD_*() macros.
>
> ...
>
>> + regval &= ~GENMASK(gpio * MA35_GP_MODE_MASK_WIDTH - 1,
>> + gpio * MA35_GP_MODE_MASK_WIDTH);
>> + regval |= mode << gpio * MA35_GP_MODE_MASK_WIDTH;
> Ditto.
>
> ...
>
>> + regval &= GENMASK(gpio * MA35_GP_MODE_MASK_WIDTH - 1,
>> + gpio * MA35_GP_MODE_MASK_WIDTH);
>> +
>> + return regval >> gpio * MA35_GP_MODE_MASK_WIDTH;
> Ditto.
>
> ...
>
>> +static int ma35_gpio_core_direction_in(struct gpio_chip *gc, unsigned int gpio)
>> +{
>> + struct ma35_pin_bank *bank = gpiochip_get_data(gc);
>> + void __iomem *reg_mode = bank->reg_base + MA35_GP_REG_MODE;
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&bank->lock, flags);
> Use cleanup.h, i.e. guard() in this case, from day 1.
> Similar approach for all other places.
>
>> + spin_unlock_irqrestore(&bank->lock, flags);
>> +
>> + return 0;
>> +}
> ...
>
>> + regval = readl(reg_dout);
>> + if (val)
>> + writel(regval | BIT(gpio), reg_dout);
>> + else
>> + writel(regval & ~BIT(gpio), reg_dout);
> Can you split regval update and make only a single writel() call? It's slightly
> better pattern
>
> read()
> if (foo)
> v =
> else
> v =
> write()
>
>> + ma35_gpio_set_mode(reg_mode, gpio, MA35_GP_MODE_OUTPUT);
> ...
>
>> + regval &= ~GENMASK(bit_offs + MA35_MFP_BITS_PER_PORT - 1, bit_offs);
> FIELD_GET()
>
> ...
>
>> + writel(1<<num, reg_intsrc);
> Oh, something happened here, besides indentation.
> Have you meant BIT() ?
>
> ...
>
>> + unsigned int num = (d->hwirq);
> Read Documentation on how to access hwirq field and what type of the value
> should be. There are plently of the examples already in the kernel. Just
> check the recent (more or less) ones.
>
> ...
>
>> + /*
>> + * The MA35_GP_REG_INTEN bits 0 ~ 15 control low-level or falling edge trigger,
>> + * while bits 16 ~ 31 control high-level or rising edge trigger.
>> + * We disable both type of interrupt.
>> + */
>> + regval &= ~(BIT(num + 16) | BIT(num));
> You have this idiom more than once in the code, make the definition and use it.
> Move comment closer to that definition.
>
> ...
>
>> + irq_set_handler_locked(d, handle_edge_irq);
>> + bank->irqtype &= ~(0x1 << num);
>> + bank->irqinten |= (0x1 << num);
>> + bank->irqinten &= ~(0x1 << (num + 16));
>> + break;
>> + case IRQ_TYPE_LEVEL_HIGH:
>> + irq_set_handler_locked(d, handle_level_irq);
>> + bank->irqtype |= (0x1 << num);
>> + bank->irqinten &= ~(0x1 << num);
>> + bank->irqinten |= (0x1 << (num + 16));
>> + break;
>> + case IRQ_TYPE_LEVEL_LOW:
>> + irq_set_handler_locked(d, handle_level_irq);
>> + bank->irqtype |= (0x1 << num);
>> + bank->irqinten &= ~(0x1 << (num + 16));
>> + bank->irqinten |= (0x1 << num);
>> + break;
> BIT() in all cases.
>
> ...
>
>
>> + irq_set_handler_locked(d, handle_bad_irq);
> Just assign it in the probe.
>
> ...
>
>> +static struct irq_chip ma35_gpio_irqchip = {
>> + .name = "MA35-GPIO-IRQ",
>> + .irq_disable = ma35_irq_gpio_mask,
>> + .irq_enable = ma35_irq_gpio_unmask,
>> + .irq_ack = ma35_irq_gpio_ack,
>> + .irq_mask = ma35_irq_gpio_mask,
>> + .irq_unmask = ma35_irq_gpio_unmask,
>> + .irq_set_type = ma35_irq_irqtype,
>> + .flags = IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_SKIP_SET_WAKE | IRQCHIP_IMMUTABLE,
> It doesn't look like IMMUTABLE. Again, check other examples, there are a lot.
>
> ...
>
>> +static void ma35_irq_demux_intgroup(struct irq_desc *desc)
>> +{
>> + struct ma35_pin_bank *bank = gpiochip_get_data(irq_desc_get_handler_data(desc));
>> + struct irq_domain *irqdomain = bank->chip.irq.domain;
>> + struct irq_chip *irqchip = irq_desc_get_chip(desc);
>> + unsigned long isr;
>> + int offset;
>> +
>> + chained_irq_enter(irqchip, desc);
>> + isr = readl(bank->reg_base + MA35_GP_REG_INTSRC);
>> + if (isr)
> Unneeded duplicate check.
>
>> + for_each_set_bit(offset, &isr, bank->nr_pins)
>> + generic_handle_irq(irq_find_mapping(irqdomain, offset));
>> +
>> + chained_irq_exit(irqchip, desc);
>> +}
> ...
>
>> + for (i = 0; i < ctrl->nr_banks; ++i, ++bank) {
> Why pre-increments?
>
>> + if (!bank->valid) {
>> + dev_warn(&pdev->dev, "bank %s is not valid\n",
>> + bank->np->name);
> Do not use fwnode / of_node name like this, use proper specifiers: %pfw / %pOF.
>
>> + continue;
>> + }
>> + bank->irqtype = 0;
>> + bank->irqinten = 0;
>> + bank->chip.label = bank->name;
>> + bank->chip.of_gpio_n_cells = 2;
>> + bank->chip.parent = &pdev->dev;
>> + bank->chip.request = ma35_gpio_core_to_request;
>> + bank->chip.direction_input = ma35_gpio_core_direction_in;
>> + bank->chip.direction_output = ma35_gpio_core_direction_out;
>> + bank->chip.get = ma35_gpio_core_get;
>> + bank->chip.set = ma35_gpio_core_set;
>> + bank->chip.base = -1;
>> + bank->chip.ngpio = bank->nr_pins;
>> + bank->chip.can_sleep = false;
>> + spin_lock_init(&bank->lock);
>> +
>> + if (bank->irq > 0) {
>> + struct gpio_irq_chip *girq;
>> +
>> + girq = &bank->chip.irq;
>> + gpio_irq_chip_set_chip(girq, &ma35_gpio_irqchip);
>> + girq->parent_handler = ma35_irq_demux_intgroup;
>> + girq->num_parents = 1;
>> +
>> + girq->parents = devm_kcalloc(&pdev->dev, 1, sizeof(*girq->parents),
> Use num_parents instead of 1.
>
>> + GFP_KERNEL);
>> + if (!girq->parents) {
>> + ret = -ENOMEM;
>> + goto fail;
>> + }
>> +
>> + girq->parents[0] = bank->irq;
>> + girq->default_type = IRQ_TYPE_NONE;
>> + girq->handler = handle_bad_irq;
>> + }
>> +
>> + ret = gpiochip_add_data(&bank->chip, bank);
>> + if (ret) {
>> + dev_err(&pdev->dev, "failed to register gpio_chip %s, error code: %d\n",
>> + bank->chip.label, ret);
>> + goto fail;
>> + }
>> + }
> ...
>
>> +fail:
>> + for (--i, --bank; i >= 0; --i, --bank) {
> while (i--) {
> bank--;
> ...
> }
>
> much better to read.
>
>> + if (!bank->valid)
>> + continue;
>> + gpiochip_remove(&bank->chip);
>> + }
>> + return ret;
>> +}
> ...
>
>> +static int ma35_get_bank_data(struct ma35_pin_bank *bank, struct ma35_pinctrl *npctl)
>> +{
>> + struct resource res;
>> +
>> + if (of_address_to_resource(bank->np, 0, &res)) {
>> + dev_err(npctl->dev, "cannot find IO resource for bank\n");
>> + return -ENOENT;
>> + }
>> +
>> + bank->reg_base = devm_ioremap_resource(npctl->dev, &res);
>> + if (IS_ERR(bank->reg_base)) {
>> + dev_err(npctl->dev, "cannot ioremap resource for bank\n");
>> + return PTR_ERR(bank->reg_base);
>> + }
> Use fwnode_iomap()
>
>> + bank->irq = irq_of_parse_and_map(bank->np, 0);
> Use fwnode_get_irq()
>
>> + bank->nr_pins = MA35_GPIO_PORT_MAX;
>> +
>> + bank->clk = of_clk_get(bank->np, 0);
> Can't you use simple clk_get()? Why?
>
>> + if (IS_ERR(bank->clk))
>> + return PTR_ERR(bank->clk);
>> +
>> + return clk_prepare_enable(bank->clk);
>> +}
> ...
>
>> + for_each_gpiochip_node(&pdev->dev, child) {
>> + struct device_node *np = to_of_node(child);
> No need, just keep everythin fwnode based.
>
>> + bank = &ctrl->pin_banks[id];
>> + bank->np = np;
>> + bank->regmap = pctl->regmap;
>> + bank->dev = &pdev->dev;
>> + if (!ma35_get_bank_data(bank, pctl))
>> + bank->valid = true;
>> + id++;
>> + }
> ...
>
>> + regval &= ~GENMASK(port * MA35_GP_PUSEL_MASK_WIDTH - 1,
>> + port * MA35_GP_PUSEL_MASK_WIDTH);
> FIELD_*()
>
> ...
>
>> + regval &= GENMASK(port * MA35_GP_PUSEL_MASK_WIDTH - 1,
>> + port * MA35_GP_PUSEL_MASK_WIDTH);
>> + regval >>= port * MA35_GP_PUSEL_MASK_WIDTH;
> Ditto.
>
> ...
>
>> + if (regval & BIT(port))
>> + return MVOLT_3300;
>> + else
>> + return MVOLT_1800;
> Can be written as
>
> return (regval & BIT()) ? _3300 : _1800;
>
> ...
>
>> + if (port < MA35_GP_DSH_BASE_PORT) {
>> + regval = readl(base + MA35_GP_REG_DSL);
>> + ds_val = (regval & GENMASK(port * 4 + 2, port * 4)) >> port * 4;
> This is too complicated way of saying
>
> ds_val = (regval >> port * 4) & GENMASK(2, 0);
>
>> + } else {
>> + port -= MA35_GP_DSH_BASE_PORT;
>> + regval = readl(base + MA35_GP_REG_DSH);
>> + ds_val = (regval & GENMASK(port * 4 + 2, port * 4)) >> port * 4;
> Ditto.
>
>> + }
> ...
>
>> + if (ma35_pinconf_get_power_source(npctl, pin) == MVOLT_1800) {
>> + for (i = 0; i < ARRAY_SIZE(ds_1800mv_tbl); i++) {
>> + if (ds_1800mv_tbl[i] == strength)
>> + ds_val = i;
> And still continue?!
>
>> + }
>> + } else {
>> + for (i = 0; i < ARRAY_SIZE(ds_3300mv_tbl); i++) {
>> + if (ds_3300mv_tbl[i] == strength)
>> + ds_val = i;
> Ditto.
>
>> + }
>> + }
> Wondering if the linear_ranges or other existing tables approaches can be used here.
>
> ...
>
>> + if (port < MA35_GP_DSH_BASE_PORT) {
>> + regval = readl(base + MA35_GP_REG_DSL);
>> + regval &= ~GENMASK(port * 4 + 2, port * 4);
>> + regval |= ds_val << port * 4;
> As per above
>
> ~(GENMASK(2, 0) << (port * 4))
>
>> + writel(regval, base + MA35_GP_REG_DSL);
>> + } else {
>> + port -= MA35_GP_DSH_BASE_PORT;
>> + regval = readl(base + MA35_GP_REG_DSH);
>> + regval &= ~GENMASK(port * 4 + 2, port * 4);
> Ditto.
>
>> + regval |= ds_val << port * 4;
>> + writel(regval, base + MA35_GP_REG_DSH);
>> + }
> ...
>
>> + regval &= ~GENMASK(port * MA35_GP_SLEWCTL_MASK_WIDTH - 1,
>> + port * MA35_GP_SLEWCTL_MASK_WIDTH);
>> + regval |= rate << port * MA35_GP_SLEWCTL_MASK_WIDTH;
> FIELD_*()
>
> ...
>
>> +static int ma35_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin, unsigned long *config)
>> +{
>> + struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
>> + enum pin_config_param param = pinconf_to_config_param(*config);
>> + u32 arg;
>> + int ret;
>> +
>> + switch (param) {
>> + case PIN_CONFIG_BIAS_DISABLE:
>> + case PIN_CONFIG_BIAS_PULL_DOWN:
>> + case PIN_CONFIG_BIAS_PULL_UP:
>> + if (ma35_pinconf_get_pull(npctl, pin) == param)
>> + arg = 1;
>> + else
>> + return -EINVAL;
>> + break;
> Check for the error case first and get rid of redundant 'else'.
>
>> + case PIN_CONFIG_DRIVE_STRENGTH:
>> + ret = ma35_pinconf_get_drive_strength(npctl, pin, &arg);
>> + if (ret)
>> + return ret;
>> + break;
>> +
>> + case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
>> + arg = ma35_pinconf_get_schmitt_enable(npctl, pin);
>> + break;
>> +
>> + case PIN_CONFIG_SLEW_RATE:
>> + arg = ma35_pinconf_get_slew_rate(npctl, pin);
>> + break;
>> +
>> + case PIN_CONFIG_OUTPUT_ENABLE:
>> + arg = ma35_pinconf_get_output(npctl, pin);
>> + break;
>> +
>> + case PIN_CONFIG_POWER_SOURCE:
>> + arg = ma35_pinconf_get_power_source(npctl, pin);
>> + break;
>> +
>> + default:
>> + return -EINVAL;
>> + }
>> + *config = pinconf_to_config_packed(param, arg);
>> +
>> + return 0;
>> +}
> ...
>
>> +static int ma35_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
>> + unsigned long *configs, unsigned int num_configs)
>> +{
>> + struct ma35_pinctrl *npctl = pinctrl_dev_get_drvdata(pctldev);
>> + enum pin_config_param param;
>> + unsigned int arg = 0;
>> + int i, ret = 0;
>> +
>> + for (i = 0; i < num_configs; i++) {
>> + param = pinconf_to_config_param(configs[i]);
>> + arg = pinconf_to_config_argument(configs[i]);
>> +
>> + switch (param) {
>> + case PIN_CONFIG_BIAS_DISABLE:
>> + case PIN_CONFIG_BIAS_PULL_UP:
>> + case PIN_CONFIG_BIAS_PULL_DOWN:
>> + ret = ma35_pinconf_set_pull(npctl, pin, param);
>> + break;
>> +
>> + case PIN_CONFIG_DRIVE_STRENGTH:
>> + ret = ma35_pinconf_set_drive_strength(npctl, pin, arg);
>> + break;
>> +
>> + case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
>> + ret = ma35_pinconf_set_schmitt(npctl, pin, 1);
>> + break;
>> +
>> + case PIN_CONFIG_INPUT_SCHMITT:
>> + ret = ma35_pinconf_set_schmitt(npctl, pin, arg);
>> + break;
>> +
>> + case PIN_CONFIG_SLEW_RATE:
>> + ret = ma35_pinconf_set_slew_rate(npctl, pin, arg);
>> + break;
>> +
>> + case PIN_CONFIG_OUTPUT_ENABLE:
>> + ret = ma35_pinconf_set_output(npctl, pin, arg);
>> + break;
>> +
>> + case PIN_CONFIG_POWER_SOURCE:
>> + ret = ma35_pinconf_set_power_source(npctl, pin, arg);
>> + break;
>> +
>> + default:
>> + return -EINVAL;
>> + }
> No returning an error if we got ret != 0?!
>
>> + }
>> + return ret;
>> +}
> ...
>
>> +static int ma35_pinctrl_parse_groups(struct device_node *np, struct ma35_pin_group *grp,
>> + struct ma35_pinctrl *npctl, u32 index)
>> +{
>> + unsigned long *configs;
>> + unsigned int nconfigs;
>> + struct ma35_pin_setting *pin;
>> + const __be32 *list;
> Huh?!
>
>> + int i, j, size, ret;
>> +
>> + dev_dbg(npctl->dev, "group(%d): %s\n", index, np->name);
>> +
>> + grp->name = np->name;
>> +
>> + ret = pinconf_generic_parse_dt_config(np, NULL, &configs, &nconfigs);
>> + if (ret)
>> + return ret;
>> +
>> + /*
>> + * the binding format is nuvoton,pins = <bank pin-mfp pin-function>,
>> + * do sanity check and calculate pins number
>> + */
> /*
> * Respect English grammar and puntuation
> * in all multi-line comments. See the difference
> * how it's done above and in this example.
> */
>
>> + list = of_get_property(np, "nuvoton,pins", &size);
> Oh, no.
> Use respective of_property_ calls.
>
>> + size /= sizeof(*list);
>> + if (!size || size % 3) {
>> + dev_err(npctl->dev, "wrong setting!\n");
>> + return -EINVAL;
>> + }
>> + grp->npins = size / 3;
>> +
>> + grp->pins = devm_kcalloc(npctl->dev, grp->npins, sizeof(*grp->pins), GFP_KERNEL);
>> + if (!grp->pins)
>> + return -ENOMEM;
>> +
>> + grp->settings = devm_kcalloc(npctl->dev, grp->npins, sizeof(*grp->settings), GFP_KERNEL);
>> + if (!grp->settings)
>> + return -ENOMEM;
>> +
>> + pin = grp->settings;
>> +
>> + for (i = 0, j = 0; i < size; i += 3, j++) {
>> + pin->offset = be32_to_cpu(*list++) * MA35_MFP_REG_SZ_PER_BANK + MA35_MFP_REG_BASE;
>> + pin->shift = (be32_to_cpu(*list++) * MA35_MFP_BITS_PER_PORT) % 32;
>> + pin->muxval = be32_to_cpu(*list++);
>> + pin->configs = configs;
>> + pin->nconfigs = nconfigs;
>> + grp->pins[j] = npctl->info->get_pin_num(pin->offset, pin->shift);
>> + pin++;
>> + }
>> + return 0;
>> +}
> ...
>
>> + for_each_child_of_node(np, child) {
>> + if (of_property_read_bool(child, "gpio-controller"))
>> + continue;
> There is a macro already present, for_each_gpiochip_node().
>
>> + npctl->nfunctions++;
>> + npctl->ngroups += of_get_child_count(child);
>> + }
> ...
>
>> + for_each_child_of_node(np, child) {
>> + if (of_property_read_bool(child, "gpio-controller"))
>> + continue;
> Ditto.
>
>> + ret = ma35_pinctrl_parse_functions(child, npctl, idx++);
>> + if (ret) {
>> + dev_err(&pdev->dev, "failed to parse function\n");
>> + of_node_put(child);
>> + return ret;
>> + }
>> + }
> ...
>
>> + if (!info || !info->pins || !info->npins) {
>> + dev_err(&pdev->dev, "wrong pinctrl info\n");
>> + return -EINVAL;
> return dev_err_probe(...);
>
>> + }
> ...
>
>> + ret = devm_pinctrl_register_and_init(&pdev->dev, ma35_pinctrl_desc,
>> + npctl, &npctl->pctl);
> Haveing
>
> struct device *dev = &pdev->dev;
>
> makes in particular this one better
>
> ret = devm_pinctrl_register_and_init(dev, ma35_pinctrl_desc, npctl, &npctl->pctl);
>
>> + if (ret)
>> + return dev_err_probe(&pdev->dev, ret, "fail to register MA35 pinctrl\n");
> ...
>
>> +int __maybe_unused ma35_pinctrl_suspend(struct device *dev)
> No __maybe_unused.
> Just use respective PM macros (pm_ptr(), DEFINE_,*PM_OPS, etc).
>
>> +{
>> + struct ma35_pinctrl *npctl = dev_get_drvdata(dev);
>> +
>> + return pinctrl_force_sleep(npctl->pctl);
>> +}
>> +
>> +int __maybe_unused ma35_pinctrl_resume(struct device *dev)
> Ditto.
>
>> +{
>> + struct ma35_pinctrl *npctl = dev_get_drvdata(dev);
>> +
>> + return pinctrl_force_default(npctl->pctl);
>> +}
> ...
>
>> +struct ma35_mux_desc {
>> + const char *name;
>> + u32 muxval;
>> +};
>> +
>> +struct ma35_pin_data {
>> + u32 offset;
>> + u32 shift;
>> + struct ma35_mux_desc *muxes;
>> +};
> Don't pin control subsystem has already some data types suitable in this cases?
>
> ...
>
>> +#define MA35_PIN(num, n, o, s, ...) { \
>> + .number = num, \
>> + .name = #n, \
> Don't we have macros for this?
>
>> + .drv_data = &(struct ma35_pin_data) { \
>> + .offset = o, \
>> + .shift = s, \
>> + .muxes = (struct ma35_mux_desc[]) { \
>> + __VA_ARGS__, { } }, \
>> + }, \
>> +}
> ...
>
>> +#include <linux/init.h>
>> +#include <linux/io.h>
>> +#include <linux/module.h>
> Missing headers and stray ones. Please, get this into order by following IWYU
> principle.
>
>> +#include <linux/of.h>
>> +#include <linux/of_device.h>
> How are these being used?
>
>> +#include <linux/pinctrl/pinctrl.h>
> ...
>
>> +static const struct dev_pm_ops ma35d1_pinctrl_pm_ops = {
>> + SET_LATE_SYSTEM_SLEEP_PM_OPS(ma35_pinctrl_suspend, ma35_pinctrl_resume)
>> +};
> New PM macros, please.
>
> ...
>
>> +static const struct of_device_id ma35d1_pinctrl_of_match[] = {
>> + { .compatible = "nuvoton,ma35d1-pinctrl", },
>> + { },
> No comma in the terminator entry.
>
>> +};
> ...
>
>> +static struct platform_driver ma35d1_pinctrl_driver = {
>> + .probe = ma35d1_pinctrl_probe,
>> + .driver = {
>> + .name = "ma35d1-pinctrl",
>> + .pm = &ma35d1_pinctrl_pm_ops,
> New PM macro here.
>
>> + .of_match_table = ma35d1_pinctrl_of_match,
>> + },
>> +};
> --
> With Best Regards,
> Andy Shevchenko
>
>
Dear Andy,
On 2024/4/10 下午 04:54, Andy Shevchenko wrote:
>> +#define MA35_GP_MODE_MASK_WIDTH 2
>> +
>> +#define MA35_GP_SLEWCTL_MASK_WIDTH 2
> I looked at the code how you use these... Oh, please switch to FIELD_GET() /
> FIELD_PREP() (don't forget to include bitfield.h)
>
> ...
>
> ...
>> + regval &= ~GENMASK(setting->shift + MA35_MFP_BITS_PER_PORT - 1,
>> + setting->shift);
> This will generate an awful code. Use respective FIELD_*() macros.
>
> ...
>
>> + regval &= ~GENMASK(gpio * MA35_GP_MODE_MASK_WIDTH - 1,
>> + gpio * MA35_GP_MODE_MASK_WIDTH);
>> + regval |= mode << gpio * MA35_GP_MODE_MASK_WIDTH;
> Ditto.
>
> ...
>
>> + regval &= GENMASK(gpio * MA35_GP_MODE_MASK_WIDTH - 1,
>> + gpio * MA35_GP_MODE_MASK_WIDTH);
>> +
>> + return regval >> gpio * MA35_GP_MODE_MASK_WIDTH;
> Ditto.
>
> ...
>
>
Allow me to remove irrelevant parts.
I attempted to follow your advice and use FIELD_GET() and FIELD_PREP(),
but found
it impractical. The reason is that these two macros require their 'mask'
argument
to be a constant, otherwise compilation errors occur, which is the issue
I encountered.
Since the mask here is calculated and not a constant, compilation errors
occur.
Taking MA35_GP_REG_MODE as an example, within 32 bits, every 2 bits
represent
the mode of a GPIO pin, and the mask is obtained by GENMASK(gpio * 2 -1,
gpio * 2),
where the 'gpio' argument is a variable, not a constant, leading to
compilation
errors.
Due to this reason, I will leave this part unchanged, or do you have any
other suggestions?
Best Regards,
Jacky Huang
On Mon, Apr 22, 2024 at 7:10 AM Jacky Huang <[email protected]> wrote:
> On 2024/4/10 下午 04:54, Andy Shevchenko wrote:
..
> >> +#define MA35_GP_MODE_MASK_WIDTH 2
> >> +
> >> +#define MA35_GP_SLEWCTL_MASK_WIDTH 2
> > I looked at the code how you use these... Oh, please switch to FIELD_GET() /
> > FIELD_PREP() (don't forget to include bitfield.h)
> >
> > ...
> >
> > ...
> >> + regval &= ~GENMASK(setting->shift + MA35_MFP_BITS_PER_PORT - 1,
> >> + setting->shift);
> > This will generate an awful code. Use respective FIELD_*() macros.
> >
> > ...
> >
> >> + regval &= ~GENMASK(gpio * MA35_GP_MODE_MASK_WIDTH - 1,
> >> + gpio * MA35_GP_MODE_MASK_WIDTH);
> >> + regval |= mode << gpio * MA35_GP_MODE_MASK_WIDTH;
> > Ditto.
> >
> > ...
> >
> >> + regval &= GENMASK(gpio * MA35_GP_MODE_MASK_WIDTH - 1,
> >> + gpio * MA35_GP_MODE_MASK_WIDTH);
> >> +
> >> + return regval >> gpio * MA35_GP_MODE_MASK_WIDTH;
> > Ditto.
..
> Allow me to remove irrelevant parts.
>
> I attempted to follow your advice and use FIELD_GET() and FIELD_PREP(),
> but found
> it impractical. The reason is that these two macros require their 'mask'
> argument
> to be a constant, otherwise compilation errors occur, which is the issue
> I encountered.
> Since the mask here is calculated and not a constant, compilation errors
> occur.
>
> Taking MA35_GP_REG_MODE as an example, within 32 bits, every 2 bits
> represent
> the mode of a GPIO pin, and the mask is obtained by GENMASK(gpio * 2 -1,
> gpio * 2),
This is not good for the compiler, it can't figure out (at least in
some _supported_ by Linux kernel versions on some architectures) that
GENMASK can be constant here just left-shifted by arbitrary bits.
> where the 'gpio' argument is a variable, not a constant, leading to
> compilation
> errors.
>
> Due to this reason, I will leave this part unchanged, or do you have any
> other suggestions?
If you need non-constant field_get()/field_prep(), add a new patch
that moves them from drivers/iio/temperature/mlx90614.c (and there are
more custom implementations:
https://elixir.bootlin.com/linux/latest/A/ident/field_get) to the
bitfield.h and use them in your code.
--
With Best Regards,
Andy Shevchenko
Dear Andy,
On 2024/4/22 下午 04:16, Andy Shevchenko wrote:
> On Mon, Apr 22, 2024 at 7:10 AM Jacky Huang <[email protected]> wrote:
>> On 2024/4/10 下午 04:54, Andy Shevchenko wrote:
> ...
>
>>>> +#define MA35_GP_MODE_MASK_WIDTH 2
>>>> +
>>>> +#define MA35_GP_SLEWCTL_MASK_WIDTH 2
>>> I looked at the code how you use these... Oh, please switch to FIELD_GET() /
>>> FIELD_PREP() (don't forget to include bitfield.h)
>>>
>>> ...
>>>
>>> ...
>>>> + regval &= ~GENMASK(setting->shift + MA35_MFP_BITS_PER_PORT - 1,
>>>> + setting->shift);
>>> This will generate an awful code. Use respective FIELD_*() macros.
>>>
>>> ...
>>>
>>>> + regval &= ~GENMASK(gpio * MA35_GP_MODE_MASK_WIDTH - 1,
>>>> + gpio * MA35_GP_MODE_MASK_WIDTH);
>>>> + regval |= mode << gpio * MA35_GP_MODE_MASK_WIDTH;
>>> Ditto.
>>>
>>> ...
>>>
>>>> + regval &= GENMASK(gpio * MA35_GP_MODE_MASK_WIDTH - 1,
>>>> + gpio * MA35_GP_MODE_MASK_WIDTH);
>>>> +
>>>> + return regval >> gpio * MA35_GP_MODE_MASK_WIDTH;
>>> Ditto.
> ...
>
>> Allow me to remove irrelevant parts.
>>
>> I attempted to follow your advice and use FIELD_GET() and FIELD_PREP(),
>> but found
>> it impractical. The reason is that these two macros require their 'mask'
>> argument
>> to be a constant, otherwise compilation errors occur, which is the issue
>> I encountered.
>> Since the mask here is calculated and not a constant, compilation errors
>> occur.
>>
>> Taking MA35_GP_REG_MODE as an example, within 32 bits, every 2 bits
>> represent
>> the mode of a GPIO pin, and the mask is obtained by GENMASK(gpio * 2 -1,
>> gpio * 2),
> This is not good for the compiler, it can't figure out (at least in
> some _supported_ by Linux kernel versions on some architectures) that
> GENMASK can be constant here just left-shifted by arbitrary bits.
>
>> where the 'gpio' argument is a variable, not a constant, leading to
>> compilation
>> errors.
>>
>> Due to this reason, I will leave this part unchanged, or do you have any
>> other suggestions?
> If you need non-constant field_get()/field_prep(), add a new patch
> that moves them from drivers/iio/temperature/mlx90614.c (and there are
> more custom implementations:
> https://elixir.bootlin.com/linux/latest/A/ident/field_get) to the
> bitfield.h and use them in your code.
>
Thank you. It works for me. I will adopt the approach used in mlx90614.c.
Best Regards,
Jacky Huang