This brings in a preliminary patch ("net: bcmgenet: Clear RGMII_LINK
upon link down") to make sure that ("net: bcmgenet: synchronize
EXT_RGMII_OOB_CTRL access") applies to the correct context.
Doug Berger (3):
net: bcmgenet: synchronize EXT_RGMII_OOB_CTRL access
net: bcmgenet: synchronize use of bcmgenet_set_rx_mode()
net: bcmgenet: synchronize UMAC_CMD access
Florian Fainelli (1):
net: bcmgenet: Clear RGMII_LINK upon link down
.../net/ethernet/broadcom/genet/bcmgenet.c | 16 ++++++++++--
.../net/ethernet/broadcom/genet/bcmgenet.h | 4 ++-
.../ethernet/broadcom/genet/bcmgenet_wol.c | 8 +++++-
drivers/net/ethernet/broadcom/genet/bcmmii.c | 25 ++++++++++++++-----
4 files changed, 43 insertions(+), 10 deletions(-)
--
2.34.1
From: Doug Berger <[email protected]>
commit d85cf67a339685beae1d0aee27b7f61da95455be upstream
The EXT_RGMII_OOB_CTRL register can be written from different
contexts. It is predominantly written from the adjust_link
handler which is synchronized by the phydev->lock, but can
also be written from a different context when configuring the
mii in bcmgenet_mii_config().
The chances of contention are quite low, but it is conceivable
that adjust_link could occur during resume when WoL is enabled
so use the phydev->lock synchronizer in bcmgenet_mii_config()
to be sure.
Fixes: afe3f907d20f ("net: bcmgenet: power on MII block for all MII modes")
Cc: [email protected]
Signed-off-by: Doug Berger <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Florian Fainelli <[email protected]>
---
drivers/net/ethernet/broadcom/genet/bcmmii.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/broadcom/genet/bcmmii.c b/drivers/net/ethernet/broadcom/genet/bcmmii.c
index cc3afb605b1e..07bb7a4e517c 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmmii.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmmii.c
@@ -2,7 +2,7 @@
/*
* Broadcom GENET MDIO routines
*
- * Copyright (c) 2014-2017 Broadcom
+ * Copyright (c) 2014-2024 Broadcom
*/
#include <linux/acpi.h>
@@ -274,6 +274,7 @@ int bcmgenet_mii_config(struct net_device *dev, bool init)
* block for the interface to work, unconditionally clear the
* Out-of-band disable since we do not need it.
*/
+ mutex_lock(&phydev->lock);
reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL);
reg &= ~OOB_DISABLE;
if (priv->ext_phy) {
@@ -285,6 +286,7 @@ int bcmgenet_mii_config(struct net_device *dev, bool init)
reg |= RGMII_MODE_EN;
}
bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
+ mutex_unlock(&phydev->lock);
if (init)
dev_info(kdev, "configuring instance for %s\n", phy_name);
--
2.34.1
From: Doug Berger <[email protected]>
commit 0d5e2a82232605b337972fb2c7d0cbc46898aca1 upstream
The UMAC_CMD register is written from different execution
contexts and has insufficient synchronization protections to
prevent possible corruption. Of particular concern are the
acceses from the phy_device delayed work context used by the
adjust_link call and the BH context that may be used by the
ndo_set_rx_mode call.
A spinlock is added to the driver to protect contended register
accesses (i.e. reg_lock) and it is used to synchronize accesses
to UMAC_CMD.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Cc: [email protected]
Signed-off-by: Doug Berger <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Florian Fainelli <[email protected]>
---
drivers/net/ethernet/broadcom/genet/bcmgenet.c | 12 +++++++++++-
drivers/net/ethernet/broadcom/genet/bcmgenet.h | 4 +++-
drivers/net/ethernet/broadcom/genet/bcmgenet_wol.c | 8 +++++++-
drivers/net/ethernet/broadcom/genet/bcmmii.c | 2 ++
4 files changed, 23 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
index 17cf89922ef6..23765f1a870e 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
@@ -2468,14 +2468,18 @@ static void umac_enable_set(struct bcmgenet_priv *priv, u32 mask, bool enable)
{
u32 reg;
+ spin_lock_bh(&priv->reg_lock);
reg = bcmgenet_umac_readl(priv, UMAC_CMD);
- if (reg & CMD_SW_RESET)
+ if (reg & CMD_SW_RESET) {
+ spin_unlock_bh(&priv->reg_lock);
return;
+ }
if (enable)
reg |= mask;
else
reg &= ~mask;
bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+ spin_unlock_bh(&priv->reg_lock);
/* UniMAC stops on a packet boundary, wait for a full-size packet
* to be processed
@@ -2491,8 +2495,10 @@ static void reset_umac(struct bcmgenet_priv *priv)
udelay(10);
/* issue soft reset and disable MAC while updating its registers */
+ spin_lock_bh(&priv->reg_lock);
bcmgenet_umac_writel(priv, CMD_SW_RESET, UMAC_CMD);
udelay(2);
+ spin_unlock_bh(&priv->reg_lock);
}
static void bcmgenet_intr_disable(struct bcmgenet_priv *priv)
@@ -3607,16 +3613,19 @@ static void bcmgenet_set_rx_mode(struct net_device *dev)
* 3. The number of filters needed exceeds the number filters
* supported by the hardware.
*/
+ spin_lock(&priv->reg_lock);
reg = bcmgenet_umac_readl(priv, UMAC_CMD);
if ((dev->flags & (IFF_PROMISC | IFF_ALLMULTI)) ||
(nfilter > MAX_MDF_FILTER)) {
reg |= CMD_PROMISC;
bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+ spin_unlock(&priv->reg_lock);
bcmgenet_umac_writel(priv, 0, UMAC_MDF_CTRL);
return;
} else {
reg &= ~CMD_PROMISC;
bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+ spin_unlock(&priv->reg_lock);
}
/* update MDF filter */
@@ -4018,6 +4027,7 @@ static int bcmgenet_probe(struct platform_device *pdev)
goto err;
}
+ spin_lock_init(&priv->reg_lock);
spin_lock_init(&priv->lock);
/* Set default pause parameters */
diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.h b/drivers/net/ethernet/broadcom/genet/bcmgenet.h
index 1985c0ec4da2..28e2c94ef835 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.h
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.h
@@ -1,6 +1,6 @@
/* SPDX-License-Identifier: GPL-2.0-only */
/*
- * Copyright (c) 2014-2020 Broadcom
+ * Copyright (c) 2014-2024 Broadcom
*/
#ifndef __BCMGENET_H__
@@ -573,6 +573,8 @@ struct bcmgenet_rxnfc_rule {
/* device context */
struct bcmgenet_priv {
void __iomem *base;
+ /* reg_lock: lock to serialize access to shared registers */
+ spinlock_t reg_lock;
enum bcmgenet_version version;
struct net_device *dev;
diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet_wol.c b/drivers/net/ethernet/broadcom/genet/bcmgenet_wol.c
index f55d9d9c01a8..56781e721497 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet_wol.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet_wol.c
@@ -2,7 +2,7 @@
/*
* Broadcom GENET (Gigabit Ethernet) Wake-on-LAN support
*
- * Copyright (c) 2014-2020 Broadcom
+ * Copyright (c) 2014-2024 Broadcom
*/
#define pr_fmt(fmt) "bcmgenet_wol: " fmt
@@ -133,6 +133,7 @@ int bcmgenet_wol_power_down_cfg(struct bcmgenet_priv *priv,
}
/* Can't suspend with WoL if MAC is still in reset */
+ spin_lock_bh(&priv->reg_lock);
reg = bcmgenet_umac_readl(priv, UMAC_CMD);
if (reg & CMD_SW_RESET)
reg &= ~CMD_SW_RESET;
@@ -140,6 +141,7 @@ int bcmgenet_wol_power_down_cfg(struct bcmgenet_priv *priv,
/* disable RX */
reg &= ~CMD_RX_EN;
bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+ spin_unlock_bh(&priv->reg_lock);
mdelay(10);
if (priv->wolopts & (WAKE_MAGIC | WAKE_MAGICSECURE)) {
@@ -185,6 +187,7 @@ int bcmgenet_wol_power_down_cfg(struct bcmgenet_priv *priv,
}
/* Enable CRC forward */
+ spin_lock_bh(&priv->reg_lock);
reg = bcmgenet_umac_readl(priv, UMAC_CMD);
priv->crc_fwd_en = 1;
reg |= CMD_CRC_FWD;
@@ -192,6 +195,7 @@ int bcmgenet_wol_power_down_cfg(struct bcmgenet_priv *priv,
/* Receiver must be enabled for WOL MP detection */
reg |= CMD_RX_EN;
bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+ spin_unlock_bh(&priv->reg_lock);
reg = UMAC_IRQ_MPD_R;
if (hfb_enable)
@@ -238,7 +242,9 @@ void bcmgenet_wol_power_up_cfg(struct bcmgenet_priv *priv,
}
/* Disable CRC Forward */
+ spin_lock_bh(&priv->reg_lock);
reg = bcmgenet_umac_readl(priv, UMAC_CMD);
reg &= ~CMD_CRC_FWD;
bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+ spin_unlock_bh(&priv->reg_lock);
}
diff --git a/drivers/net/ethernet/broadcom/genet/bcmmii.c b/drivers/net/ethernet/broadcom/genet/bcmmii.c
index 07bb7a4e517c..f21f2aaa6fd9 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmmii.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmmii.c
@@ -75,6 +75,7 @@ static void bcmgenet_mac_config(struct net_device *dev)
reg |= RGMII_LINK;
bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
+ spin_lock_bh(&priv->reg_lock);
reg = bcmgenet_umac_readl(priv, UMAC_CMD);
reg &= ~((CMD_SPEED_MASK << CMD_SPEED_SHIFT) |
CMD_HD_EN |
@@ -87,6 +88,7 @@ static void bcmgenet_mac_config(struct net_device *dev)
reg |= CMD_TX_EN | CMD_RX_EN;
}
bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+ spin_unlock_bh(&priv->reg_lock);
priv->eee.eee_active = phy_init_eee(phydev, 0) >= 0;
bcmgenet_eee_enable_set(dev,
--
2.34.1
On Wed, May 15, 2024 at 10:02:23AM -0700, Florian Fainelli wrote:
> This brings in a preliminary patch ("net: bcmgenet: Clear RGMII_LINK
> upon link down") to make sure that ("net: bcmgenet: synchronize
> EXT_RGMII_OOB_CTRL access") applies to the correct context.
That seems to resolve the issue on 6.1 stable for me.
From: Florian Fainelli <[email protected]>
commit 696450c05181559a35d4d5bee55c465b1ac6fe2e upstream
Clear the RGMII_LINK bit upon detecting link down to be consistent with
setting the bit upon link up. We also move the clearing of the
out-of-band disable to the runtime initialization rather than for each
link up/down transition.
Signed-off-by: Florian Fainelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: Florian Fainelli <[email protected]>
---
drivers/net/ethernet/broadcom/genet/bcmmii.c | 19 ++++++++++++++-----
1 file changed, 14 insertions(+), 5 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/genet/bcmmii.c b/drivers/net/ethernet/broadcom/genet/bcmmii.c
index 1779ee524dac..cc3afb605b1e 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmmii.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmmii.c
@@ -72,7 +72,6 @@ static void bcmgenet_mac_config(struct net_device *dev)
* Receive clock is provided by the PHY.
*/
reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL);
- reg &= ~OOB_DISABLE;
reg |= RGMII_LINK;
bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
@@ -100,10 +99,18 @@ static void bcmgenet_mac_config(struct net_device *dev)
*/
void bcmgenet_mii_setup(struct net_device *dev)
{
+ struct bcmgenet_priv *priv = netdev_priv(dev);
struct phy_device *phydev = dev->phydev;
+ u32 reg;
- if (phydev->link)
+ if (phydev->link) {
bcmgenet_mac_config(dev);
+ } else {
+ reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL);
+ reg &= ~RGMII_LINK;
+ bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
+ }
+
phy_print_status(phydev);
}
@@ -264,18 +271,20 @@ int bcmgenet_mii_config(struct net_device *dev, bool init)
(priv->phy_interface != PHY_INTERFACE_MODE_MOCA);
/* This is an external PHY (xMII), so we need to enable the RGMII
- * block for the interface to work
+ * block for the interface to work, unconditionally clear the
+ * Out-of-band disable since we do not need it.
*/
+ reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL);
+ reg &= ~OOB_DISABLE;
if (priv->ext_phy) {
- reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL);
reg &= ~ID_MODE_DIS;
reg |= id_mode_dis;
if (GENET_IS_V1(priv) || GENET_IS_V2(priv) || GENET_IS_V3(priv))
reg |= RGMII_MODE_EN_V123;
else
reg |= RGMII_MODE_EN;
- bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
}
+ bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
if (init)
dev_info(kdev, "configuring instance for %s\n", phy_name);
--
2.34.1
From: Doug Berger <[email protected]>
commit 2dbe5f19368caae63b1f59f5bc2af78c7d522b3a upstream
The ndo_set_rx_mode function is synchronized with the
netif_addr_lock spinlock and BHs disabled. Since this
function is also invoked directly from the driver the
same synchronization should be applied.
Fixes: 72f96347628e ("net: bcmgenet: set Rx mode before starting netif")
Cc: [email protected]
Signed-off-by: Doug Berger <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Florian Fainelli <[email protected]>
---
drivers/net/ethernet/broadcom/genet/bcmgenet.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
index c2a991308215..17cf89922ef6 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
@@ -2,7 +2,7 @@
/*
* Broadcom GENET (Gigabit Ethernet) controller driver
*
- * Copyright (c) 2014-2020 Broadcom
+ * Copyright (c) 2014-2024 Broadcom
*/
#define pr_fmt(fmt) "bcmgenet: " fmt
@@ -3344,7 +3344,9 @@ static void bcmgenet_netif_start(struct net_device *dev)
struct bcmgenet_priv *priv = netdev_priv(dev);
/* Start the network engine */
+ netif_addr_lock_bh(dev);
bcmgenet_set_rx_mode(dev);
+ netif_addr_unlock_bh(dev);
bcmgenet_enable_rx_napi(priv);
umac_enable_set(priv, CMD_TX_EN | CMD_RX_EN, true);
--
2.34.1
On Wed, May 15, 2024 at 06:35:55PM +0100, Mark Brown wrote:
> On Wed, May 15, 2024 at 10:02:23AM -0700, Florian Fainelli wrote:
> > This brings in a preliminary patch ("net: bcmgenet: Clear RGMII_LINK
> > upon link down") to make sure that ("net: bcmgenet: synchronize
> > EXT_RGMII_OOB_CTRL access") applies to the correct context.
>
> That seems to resolve the issue on 6.1 stable for me.
Great, thanks for testing and letting us know. I've queued these up and
will push out a -rc3 now.
greg k-h