Convert g762 Documentation to yaml schema.
Since it supports various device, change the name to g76x and add the
vendor prefix.
Signed-off-by: Christian Marangi <[email protected]>
---
.../devicetree/bindings/hwmon/g762.txt | 47 -----------
.../devicetree/bindings/hwmon/gmt,g76x.yaml | 83 +++++++++++++++++++
2 files changed, 83 insertions(+), 47 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/hwmon/g762.txt
create mode 100644 Documentation/devicetree/bindings/hwmon/gmt,g76x.yaml
diff --git a/Documentation/devicetree/bindings/hwmon/g762.txt b/Documentation/devicetree/bindings/hwmon/g762.txt
deleted file mode 100644
index 6d154c4923de..000000000000
--- a/Documentation/devicetree/bindings/hwmon/g762.txt
+++ /dev/null
@@ -1,47 +0,0 @@
-GMT G762/G763 PWM Fan controller
-
-Required node properties:
-
- - "compatible": must be either "gmt,g762" or "gmt,g763"
- - "reg": I2C bus address of the device
- - "clocks": a fixed clock providing input clock frequency
- on CLK pin of the chip.
-
-Optional properties:
-
- - "fan_startv": fan startup voltage. Accepted values are 0, 1, 2 and 3.
- The higher the more.
-
- - "pwm_polarity": pwm polarity. Accepted values are 0 (positive duty)
- and 1 (negative duty).
-
- - "fan_gear_mode": fan gear mode. Supported values are 0, 1 and 2.
-
-If an optional property is not set in .dts file, then current value is kept
-unmodified (e.g. u-boot installed value).
-
-Additional information on operational parameters for the device is available
-in Documentation/hwmon/g762.rst. A detailed datasheet for the device is available
-at http://natisbad.org/NAS/refs/GMT_EDS-762_763-080710-0.2.pdf.
-
-Example g762 node:
-
- clocks {
- #address-cells = <1>;
- #size-cells = <0>;
-
- g762_clk: fixedclk {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <8192>;
- }
- }
-
- g762: g762@3e {
- compatible = "gmt,g762";
- reg = <0x3e>;
- clocks = <&g762_clk>
- fan_gear_mode = <0>; /* chip default */
- fan_startv = <1>; /* chip default */
- pwm_polarity = <0>; /* chip default */
- };
diff --git a/Documentation/devicetree/bindings/hwmon/gmt,g76x.yaml b/Documentation/devicetree/bindings/hwmon/gmt,g76x.yaml
new file mode 100644
index 000000000000..bfefe49f54bf
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/gmt,g76x.yaml
@@ -0,0 +1,83 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/hwmon/gmt,g76x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: GMT G762/G763 PWM Fan controller
+
+maintainers:
+ - Christian Marangi <[email protected]>
+
+description: |
+ GMT G762/G763 PWM Fan controller.
+
+ If an optional property is not set in DT, then current value is kept
+ unmodified (e.g. bootloader installed value).
+
+ Additional information on operational parameters for the device is available
+ in Documentation/hwmon/g762.rst. A detailed datasheet for the device is available
+ at http://natisbad.org/NAS/refs/GMT_EDS-762_763-080710-0.2.pdf.
+
+properties:
+ compatible:
+ enum:
+ - gmt,g762
+ - gmt,g763
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ description: a fixed clock providing input clock frequency on CLK
+ pin of the chip.
+ maxItems: 1
+
+ fan_startv:
+ description: Fan startup voltage step
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+
+ pwm_polarity:
+ description: PWM polarity (psotivie or negative duty)
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1]
+
+ fan_gear_mode:
+ description: FAN gear mode. Configure High speed fan setting factor
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2]
+
+required:
+ - compatible
+ - reg
+ - clocks
+
+additionalProperties: false
+
+examples:
+ - |
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ g762_clk: fixedclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <8192>;
+ };
+ };
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ g762@3e {
+ compatible = "gmt,g762";
+ reg = <0x3e>;
+ clocks = <&g762_clk>;
+ fan_gear_mode = <0>;
+ fan_startv = <1>;
+ pwm_polarity = <0>;
+ };
+ };
--
2.43.0
Add support for g761 PWM Fan controller. This is an exact copy of g763
with the difference that it does also support an internal clock
oscillator.
With clocks property not defined, the internal clock oscillator is used.
Signed-off-by: Christian Marangi <[email protected]>
---
Changes v2:
- Drop internal-clock property
.../devicetree/bindings/hwmon/gmt,g76x.yaml | 29 +++++++++++++++++--
1 file changed, 26 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/hwmon/gmt,g76x.yaml b/Documentation/devicetree/bindings/hwmon/gmt,g76x.yaml
index bfefe49f54bf..6dadd24efca2 100644
--- a/Documentation/devicetree/bindings/hwmon/gmt,g76x.yaml
+++ b/Documentation/devicetree/bindings/hwmon/gmt,g76x.yaml
@@ -4,13 +4,17 @@
$id: http://devicetree.org/schemas/hwmon/gmt,g76x.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
-title: GMT G762/G763 PWM Fan controller
+title: GMT G761/G762/G763 PWM Fan controller
maintainers:
- Christian Marangi <[email protected]>
description: |
- GMT G762/G763 PWM Fan controller.
+ GMT G761/G762/G763 PWM Fan controller.
+
+ G761 supports an internal-clock hence the clocks property is optional.
+ If not defined, internal-clock will be used. (31KHz is the clock of
+ the internal crystal oscillator)
If an optional property is not set in DT, then current value is kept
unmodified (e.g. bootloader installed value).
@@ -22,6 +26,7 @@ description: |
properties:
compatible:
enum:
+ - gmt,g761
- gmt,g762
- gmt,g763
@@ -51,7 +56,17 @@ properties:
required:
- compatible
- reg
- - clocks
+
+if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - gmt,g762
+ - gmt,g763
+then:
+ required:
+ - clocks
additionalProperties: false
@@ -80,4 +95,12 @@ examples:
fan_startv = <1>;
pwm_polarity = <0>;
};
+
+ g761@1e {
+ compatible = "gmt,g761";
+ reg = <0x1e>;
+ fan_gear_mode = <0>;
+ fan_startv = <1>;
+ pwm_polarity = <0>;
+ };
};
--
2.43.0
Add support for g761 PWM Fan Controller.
The g761 is a copy of the g763 with the only difference of supporting
and internal clock. The internal clock is used if no clocks property is
defined in device node and in such case the required bit is enabled and
clock handling is skipped.
The internal clock oscillator runs at 31KHz.
Signed-off-by: Christian Marangi <[email protected]>
---
Changes v2:
- Rework handling of internal clock
drivers/hwmon/g762.c | 33 ++++++++++++++++++++++++++++++---
1 file changed, 30 insertions(+), 3 deletions(-)
diff --git a/drivers/hwmon/g762.c b/drivers/hwmon/g762.c
index af1228708e25..a00cf3245eec 100644
--- a/drivers/hwmon/g762.c
+++ b/drivers/hwmon/g762.c
@@ -69,6 +69,7 @@ enum g762_regs {
#define G762_REG_FAN_CMD1_PWM_POLARITY 0x02 /* PWM polarity */
#define G762_REG_FAN_CMD1_PULSE_PER_REV 0x01 /* pulse per fan revolution */
+#define G761_REG_FAN_CMD2_FAN_CLOCK 0x20 /* choose internal clock*/
#define G762_REG_FAN_CMD2_GEAR_MODE_1 0x08 /* fan gear mode */
#define G762_REG_FAN_CMD2_GEAR_MODE_0 0x04
#define G762_REG_FAN_CMD2_FAN_STARTV_1 0x02 /* fan startup voltage */
@@ -115,6 +116,7 @@ enum g762_regs {
struct g762_data {
struct i2c_client *client;
+ bool internal_clock;
struct clk *clk;
/* update mutex */
@@ -566,6 +568,7 @@ static int do_set_fan_startv(struct device *dev, unsigned long val)
#ifdef CONFIG_OF
static const struct of_device_id g762_dt_match[] = {
+ { .compatible = "gmt,g761" },
{ .compatible = "gmt,g762" },
{ .compatible = "gmt,g763" },
{ },
@@ -597,6 +600,21 @@ static int g762_of_clock_enable(struct i2c_client *client)
if (!client->dev.of_node)
return 0;
+ data = i2c_get_clientdata(client);
+
+ /*
+ * Skip CLK detection and handling if we use internal clock.
+ * This is only valid for g761.
+ */
+ data->internal_clock = of_device_is_compatible(client->dev.of_node,
+ "gmt,g761") &&
+ !of_property_present(client->dev.of_node,
+ "clocks");
+ if (data->internal_clock) {
+ do_set_clk_freq(&client->dev, 32768);
+ return 0;
+ }
+
clk = of_clk_get(client->dev.of_node, 0);
if (IS_ERR(clk)) {
dev_err(&client->dev, "failed to get clock\n");
@@ -616,7 +634,6 @@ static int g762_of_clock_enable(struct i2c_client *client)
goto clk_unprep;
}
- data = i2c_get_clientdata(client);
data->clk = clk;
ret = devm_add_action(&client->dev, g762_of_clock_disable, data);
@@ -1025,16 +1042,26 @@ ATTRIBUTE_GROUPS(g762);
static inline int g762_fan_init(struct device *dev)
{
struct g762_data *data = g762_update_client(dev);
+ int ret;
if (IS_ERR(data))
return PTR_ERR(data);
+ /* internal_clock can only be set with compatible g761 */
+ if (data->internal_clock)
+ data->fan_cmd2 |= G761_REG_FAN_CMD2_FAN_CLOCK;
+
data->fan_cmd1 |= G762_REG_FAN_CMD1_DET_FAN_FAIL;
data->fan_cmd1 |= G762_REG_FAN_CMD1_DET_FAN_OOC;
data->valid = false;
- return i2c_smbus_write_byte_data(data->client, G762_REG_FAN_CMD1,
- data->fan_cmd1);
+ ret = i2c_smbus_write_byte_data(data->client, G762_REG_FAN_CMD1,
+ data->fan_cmd1);
+ if (ret)
+ return ret;
+
+ return i2c_smbus_write_byte_data(data->client, G762_REG_FAN_CMD2,
+ data->fan_cmd2);
}
static int g762_probe(struct i2c_client *client)
--
2.43.0
On Sun, May 26, 2024 at 08:45:24PM +0200, Christian Marangi wrote:
> Add support for g761 PWM Fan controller. This is an exact copy of g763
> with the difference that it does also support an internal clock
> oscillator.
>
> With clocks property not defined, the internal clock oscillator is used.
>
> Signed-off-by: Christian Marangi <[email protected]>
Reviewed-by: Conor Dooley <[email protected]>
Thanks,
Conor.
On Sun, May 26, 2024 at 08:45:23PM +0200, Christian Marangi wrote:
> Convert g762 Documentation to yaml schema.
>
> Since it supports various device, change the name to g76x and add the
> vendor prefix.
The file name should not change. This document does not cover g76[0,4-9],
after all.
Guenter
>
> Signed-off-by: Christian Marangi <[email protected]>
> ---
> .../devicetree/bindings/hwmon/g762.txt | 47 -----------
> .../devicetree/bindings/hwmon/gmt,g76x.yaml | 83 +++++++++++++++++++
> 2 files changed, 83 insertions(+), 47 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/hwmon/g762.txt
> create mode 100644 Documentation/devicetree/bindings/hwmon/gmt,g76x.yaml
>
> diff --git a/Documentation/devicetree/bindings/hwmon/g762.txt b/Documentation/devicetree/bindings/hwmon/g762.txt
> deleted file mode 100644
> index 6d154c4923de..000000000000
> --- a/Documentation/devicetree/bindings/hwmon/g762.txt
> +++ /dev/null
> @@ -1,47 +0,0 @@
> -GMT G762/G763 PWM Fan controller
> -
> -Required node properties:
> -
> - - "compatible": must be either "gmt,g762" or "gmt,g763"
> - - "reg": I2C bus address of the device
> - - "clocks": a fixed clock providing input clock frequency
> - on CLK pin of the chip.
> -
> -Optional properties:
> -
> - - "fan_startv": fan startup voltage. Accepted values are 0, 1, 2 and 3.
> - The higher the more.
> -
> - - "pwm_polarity": pwm polarity. Accepted values are 0 (positive duty)
> - and 1 (negative duty).
> -
> - - "fan_gear_mode": fan gear mode. Supported values are 0, 1 and 2.
> -
> -If an optional property is not set in .dts file, then current value is kept
> -unmodified (e.g. u-boot installed value).
> -
> -Additional information on operational parameters for the device is available
> -in Documentation/hwmon/g762.rst. A detailed datasheet for the device is available
> -at http://natisbad.org/NAS/refs/GMT_EDS-762_763-080710-0.2.pdf.
> -
> -Example g762 node:
> -
> - clocks {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - g762_clk: fixedclk {
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <8192>;
> - }
> - }
> -
> - g762: g762@3e {
> - compatible = "gmt,g762";
> - reg = <0x3e>;
> - clocks = <&g762_clk>
> - fan_gear_mode = <0>; /* chip default */
> - fan_startv = <1>; /* chip default */
> - pwm_polarity = <0>; /* chip default */
> - };
> diff --git a/Documentation/devicetree/bindings/hwmon/gmt,g76x.yaml b/Documentation/devicetree/bindings/hwmon/gmt,g76x.yaml
> new file mode 100644
> index 000000000000..bfefe49f54bf
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/hwmon/gmt,g76x.yaml
> @@ -0,0 +1,83 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/hwmon/gmt,g76x.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: GMT G762/G763 PWM Fan controller
> +
> +maintainers:
> + - Christian Marangi <[email protected]>
> +
> +description: |
> + GMT G762/G763 PWM Fan controller.
> +
> + If an optional property is not set in DT, then current value is kept
> + unmodified (e.g. bootloader installed value).
> +
> + Additional information on operational parameters for the device is available
> + in Documentation/hwmon/g762.rst. A detailed datasheet for the device is available
> + at http://natisbad.org/NAS/refs/GMT_EDS-762_763-080710-0.2.pdf.
> +
> +properties:
> + compatible:
> + enum:
> + - gmt,g762
> + - gmt,g763
> +
> + reg:
> + maxItems: 1
> +
> + clocks:
> + description: a fixed clock providing input clock frequency on CLK
> + pin of the chip.
> + maxItems: 1
> +
> + fan_startv:
> + description: Fan startup voltage step
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1, 2, 3]
> +
> + pwm_polarity:
> + description: PWM polarity (psotivie or negative duty)
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1]
> +
> + fan_gear_mode:
> + description: FAN gear mode. Configure High speed fan setting factor
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1, 2]
> +
> +required:
> + - compatible
> + - reg
> + - clocks
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + clocks {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + g762_clk: fixedclk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <8192>;
> + };
> + };
> +
> + i2c {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + g762@3e {
> + compatible = "gmt,g762";
> + reg = <0x3e>;
> + clocks = <&g762_clk>;
> + fan_gear_mode = <0>;
> + fan_startv = <1>;
> + pwm_polarity = <0>;
> + };
> + };