Introduce k3-am62-lp-sk-nand.dtso overlay file to support
the X8 NAND EXPANSION BOARD card (PROC143E1) for AM62x LP SK
board. NAND has partitions for different boot components as
below:
0x000000000000-0x000000200000 : "NAND.tiboot3
0x000000200000-0x000000400000 : "NAND.tispl
0x000000400000-0x000000600000 : "NAND.tiboot3.backup
0x000000600000-0x000000a00000 : "NAND.u-boot
0x000000a00000-0x000000a40000 : "NAND.u-boot-env
0x000000a40000-0x000000a80000 : "NAND.u-boot-env.backup
0x000000a80000-0x000040000000 : "NAND.file-system
Disable mcasp1 node in DT to avoid pinmux conflict. Update
Makefile to include k3-am62-lp-sk-nand.dtso.
Signed-off-by: Nitin Yadav <[email protected]>
---
arch/arm64/boot/dts/ti/Makefile | 2 +
.../arm64/boot/dts/ti/k3-am62-lp-sk-nand.dtso | 119 ++++++++++++++++++
2 files changed, 121 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-am62-lp-sk-nand.dtso
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index b3516419f95d..9aea8bdea44f 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -19,6 +19,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-dahlia.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-dev.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-yavia.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am62-lp-sk.dtb
+k3-am62-lp-sk-nand-dtbs := k3-am62-lp-sk.dtb k3-am62-lp-sk-nand.dtbo
+dtb-$(CONFIG_ARCH_K3) += k3-am62-lp-sk-nand.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am62x-sk-hdmi-audio.dtbo
# Boards with AM62Ax SoC
diff --git a/arch/arm64/boot/dts/ti/k3-am62-lp-sk-nand.dtso b/arch/arm64/boot/dts/ti/k3-am62-lp-sk-nand.dtso
new file mode 100644
index 000000000000..0f4e26db534b
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62-lp-sk-nand.dtso
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022-2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#include "k3-pinctrl.h"
+
+&mcasp1 {
+ status = "disabled";
+};
+
+&main_pmx0 {
+ gpmc0_pins_default: gpmc0-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x003c, PIN_INPUT, 0) /* (M25) GPMC0_AD0 */
+ AM62X_IOPAD(0x0040, PIN_INPUT, 0) /* (N23) GPMC0_AD1 */
+ AM62X_IOPAD(0x0044, PIN_INPUT, 0) /* (N24) GPMC0_AD2 */
+ AM62X_IOPAD(0x0048, PIN_INPUT, 0) /* (N25) GPMC0_AD3 */
+ AM62X_IOPAD(0x004c, PIN_INPUT, 0) /* (P24) GPMC0_AD4 */
+ AM62X_IOPAD(0x0050, PIN_INPUT, 0) /* (P22) GPMC0_AD5 */
+ AM62X_IOPAD(0x0054, PIN_INPUT, 0) /* (P21) GPMC0_AD6 */
+ AM62X_IOPAD(0x0058, PIN_INPUT, 0) /* (R23) GPMC0_AD7 */
+ AM62X_IOPAD(0x0084, PIN_OUTPUT, 0) /* (L23) GPMC0_ADVn_ALE */
+ AM62X_IOPAD(0x0088, PIN_OUTPUT, 0) /* (L24) GPMC0_OEn_REn */
+ AM62X_IOPAD(0x008c, PIN_OUTPUT, 0) /* (L25) GPMC0_WEn */
+ AM62X_IOPAD(0x0090, PIN_OUTPUT, 0) /* (M24) GPMC0_BE0n_CLE */
+ AM62X_IOPAD(0x00a8, PIN_OUTPUT, 0) /* (M21) GPMC0_CSn0 */
+ AM62X_IOPAD(0x0098, PIN_INPUT, 0) /* (U23) GPMC0_WAIT0 */
+ >;
+ };
+};
+
+&gpmc0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmc0_pins_default>;
+ ranges = <0 0 0x00 0x51000000 0x01000000>; /* CS0 space. Min partition = 16MB */
+ #address-cells = <2>;
+ #size-cells = <1>;
+
+ nand0_0: nand@0,0 {
+ compatible = "ti,am64-nand";
+ reg = <0 0 64>; /* device IO registers */
+ interrupt-parent = <&gpmc0>;
+ interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+ <1 IRQ_TYPE_NONE>; /* termcount */
+ rb-gpios = <&gpmc0 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
+ ti,nand-xfer-type = "prefetch-polled";
+ ti,nand-ecc-opt = "bch8"; /* BCH8: Bootrom limitation */
+ ti,elm-id = <&elm0>;
+ nand-bus-width = <8>;
+ gpmc,device-width = <1>;
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <40>;
+ gpmc,cs-wr-off-ns = <40>;
+ gpmc,adv-on-ns = <0>;
+ gpmc,adv-rd-off-ns = <25>;
+ gpmc,adv-wr-off-ns = <25>;
+ gpmc,we-on-ns = <0>;
+ gpmc,we-off-ns = <20>;
+ gpmc,oe-on-ns = <3>;
+ gpmc,oe-off-ns = <30>;
+ gpmc,access-ns = <30>;
+ gpmc,rd-cycle-ns = <40>;
+ gpmc,wr-cycle-ns = <40>;
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <0>;
+ gpmc,clk-activation-ns = <0>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "NAND.tiboot3";
+ reg = <0x00000000 0x00200000>; /* 2M */
+ };
+ partition@200000 {
+ label = "NAND.tispl";
+ reg = <0x00200000 0x00200000>; /* 2M */
+ };
+ partition@400000 {
+ label = "NAND.tiboot3.backup"; /* 2M */
+ reg = <0x00400000 0x00200000>; /* BootROM looks at 4M */
+ };
+ partition@600000 {
+ label = "NAND.u-boot";
+ reg = <0x00600000 0x00400000>; /* 4M */
+ };
+ partition@a00000 {
+ label = "NAND.u-boot-env";
+ reg = <0x00a00000 0x00040000>; /* 256K */
+ };
+ partition@a40000 {
+ label = "NAND.u-boot-env.backup";
+ reg = <0x00a40000 0x00040000>; /* 256K */
+ };
+ partition@a80000 {
+ label = "NAND.file-system";
+ reg = <0x00a80000 0x3f580000>;
+ };
+ };
+ };
+};
+
+&elm0{
+ status = "okay";
+};
--
2.25.1
On 4.10.2023 14.12, Nitin Yadav wrote:
> Introduce k3-am62-lp-sk-nand.dtso overlay file to support
> the X8 NAND EXPANSION BOARD card (PROC143E1) for AM62x LP SK
> board. NAND has partitions for different boot components as
> below:
>
> 0x000000000000-0x000000200000 : "NAND.tiboot3
> 0x000000200000-0x000000400000 : "NAND.tispl
> 0x000000400000-0x000000600000 : "NAND.tiboot3.backup
> 0x000000600000-0x000000a00000 : "NAND.u-boot
> 0x000000a00000-0x000000a40000 : "NAND.u-boot-env
> 0x000000a40000-0x000000a80000 : "NAND.u-boot-env.backup
> 0x000000a80000-0x000040000000 : "NAND.file-system
>
> Disable mcasp1 node in DT to avoid pinmux conflict. Update
> Makefile to include k3-am62-lp-sk-nand.dtso.
>
> Signed-off-by: Nitin Yadav <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>