Add a new board name.
Signed-off-by: Denis Burkov <[email protected]>
---
Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
index 09d835db6db5..43491e7f8a5e 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@@ -774,6 +774,11 @@ properties:
- const: pocketbook,touch-lux-3
- const: allwinner,sun5i-a13
+ - description: PocketBook 614 Plus
+ items:
+ - const: pocketbook,614-plus
+ - const: allwinner,sun5i-a13
+
- description: Point of View Protab2-IPS9
items:
- const: pov,protab2-ips9
--
2.43.0
What works:
- Serial console
- mmc0, mmc2 (both microSD card slots on the board)
- All buttons (gpio and lradc based)
- Power LED
- PMIC
- RTC
- USB OTG/gadgets mode
Signed-off-by: Denis Burkov <[email protected]>
---
arch/arm/boot/dts/allwinner/Makefile | 2 +
.../sun5i-a13-pocketbook-614-plus.dts | 254 ++++++++++++++++++
2 files changed, 256 insertions(+)
create mode 100644 arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile
index 2d26c3397f14..fe321865beed 100644
--- a/arch/arm/boot/dts/allwinner/Makefile
+++ b/arch/arm/boot/dts/allwinner/Makefile
@@ -61,6 +61,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
sun5i-a13-olinuxino.dtb \
sun5i-a13-olinuxino-micro.dtb \
sun5i-a13-pocketbook-touch-lux-3.dtb \
+ sun5i-a13-pocketbook-614-plus.dtb \
sun5i-a13-q8-tablet.dtb \
sun5i-a13-utoo-p66.dtb \
sun5i-gr8-chip-pro.dtb \
@@ -82,6 +83,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
sun5i-a13-olinuxino.dtb \
sun5i-a13-olinuxino-micro.dtb \
sun5i-a13-pocketbook-touch-lux-3.dtb \
+ sun5i-a13-pocketbook-614-plus.dtb \
sun5i-a13-q8-tablet.dtb \
sun5i-a13-utoo-p66.dtb \
sun5i-gr8-chip-pro.dtb \
diff --git a/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
new file mode 100644
index 000000000000..89898fa16ff7
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
@@ -0,0 +1,254 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2024 Denis Burkov <[email protected]>
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "PocketBook 614 Plus";
+ compatible = "pocketbook,614-plus", "allwinner,sun5i-a13";
+
+ aliases {
+ serial0 = &uart1;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ rtc0 = &pcf8563;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_pocketbook>;
+
+ led {
+ gpios = <&pio 4 8 GPIO_ACTIVE_LOW>; /* PE8 */
+ default-state = "on";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+ label = "GPIO Keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pocketbook_btn_pins>;
+
+ key-right {
+ label = "Right";
+ linux,code = <KEY_NEXT>;
+ gpios = <&pio 6 9 GPIO_ACTIVE_LOW>; /* PG9 */
+ };
+
+ key-left {
+ label = "Left";
+ linux,code = <KEY_PREVIOUS>;
+ gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 */
+ };
+ };
+
+ reg_3v3_mmc0: regulator-mmc0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-mmc0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pocketbook_reg_mmc0_pins>;
+ gpio = <&pio 4 4 GPIO_ACTIVE_LOW>; /* PE4 */
+ vin-supply = <®_vcc3v3>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupts = <0>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&i2c1 {
+ status = "okay";
+
+ pcf8563: rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ };
+};
+
+&i2c2 {
+ status = "okay";
+
+ /* Touchpanel is connected here. */
+};
+
+&lradc {
+ vref-supply = <®_ldo2>;
+ status = "okay";
+
+ button-300 {
+ label = "Down";
+ linux,code = <KEY_DOWN>;
+ channel = <0>;
+ voltage = <300000>;
+ };
+
+ button-700 {
+ label = "Up";
+ linux,code = <KEY_UP>;
+ channel = <0>;
+ voltage = <700000>;
+ };
+
+ button-1000 {
+ label = "Left";
+ linux,code = <KEY_LEFT>;
+ channel = <0>;
+ voltage = <1000000>;
+ };
+
+ button-1200 {
+ label = "Menu";
+ linux,code = <KEY_MENU>;
+ channel = <0>;
+ voltage = <1200000>;
+ };
+
+ button-1500 {
+ label = "Right";
+ linux,code = <KEY_RIGHT>;
+ channel = <0>;
+ voltage = <1500000>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <®_3v3_mmc0>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_4bit_pc_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ led_pins_pocketbook: led-pin {
+ pins = "PE8";
+ function = "gpio_out";
+ };
+ pocketbook_btn_pins: btn-pins {
+ pins = "PG9", "PG10";
+ function = "gpio_in";
+ bias-pull-up;
+ };
+ pocketbook_reg_mmc0_pins: reg-mmc0-pins {
+ pins = "PE4";
+ function = "gpio_out";
+ };
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_ldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_usb0_vbus {
+ status = "okay";
+ gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+};
+
+®_usb1_vbus {
+ gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pg_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&battery_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 6 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG2 */
+ usb0_vbus_det-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
--
2.43.0
Hi Denis!
Dne četrtek, 14. marec 2024 ob 16:53:06 CET je Denis Burkov napisal(a):
> What works:
>
> - Serial console
> - mmc0, mmc2 (both microSD card slots on the board)
> - All buttons (gpio and lradc based)
> - Power LED
> - PMIC
> - RTC
> - USB OTG/gadgets mode
>
> Signed-off-by: Denis Burkov <[email protected]>
> ---
> arch/arm/boot/dts/allwinner/Makefile | 2 +
> .../sun5i-a13-pocketbook-614-plus.dts | 254 ++++++++++++++++++
> 2 files changed, 256 insertions(+)
> create mode 100644 arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
>
> diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile
> index 2d26c3397f14..fe321865beed 100644
> --- a/arch/arm/boot/dts/allwinner/Makefile
> +++ b/arch/arm/boot/dts/allwinner/Makefile
> @@ -61,6 +61,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
> sun5i-a13-olinuxino.dtb \
> sun5i-a13-olinuxino-micro.dtb \
> sun5i-a13-pocketbook-touch-lux-3.dtb \
> + sun5i-a13-pocketbook-614-plus.dtb \
> sun5i-a13-q8-tablet.dtb \
> sun5i-a13-utoo-p66.dtb \
> sun5i-gr8-chip-pro.dtb \
> @@ -82,6 +83,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
> sun5i-a13-olinuxino.dtb \
> sun5i-a13-olinuxino-micro.dtb \
> sun5i-a13-pocketbook-touch-lux-3.dtb \
> + sun5i-a13-pocketbook-614-plus.dtb \
> sun5i-a13-q8-tablet.dtb \
> sun5i-a13-utoo-p66.dtb \
> sun5i-gr8-chip-pro.dtb \
This merge artefact. Can you add patch before this one and remove duplicate definitions?
> diff --git a/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
> new file mode 100644
> index 000000000000..89898fa16ff7
> --- /dev/null
> +++ b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
> @@ -0,0 +1,254 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright 2024 Denis Burkov <[email protected]>
> + */
> +
> +/dts-v1/;
> +#include "sun5i-a13.dtsi"
> +#include "sunxi-common-regulators.dtsi"
Extra empty line here.
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> + model = "PocketBook 614 Plus";
> + compatible = "pocketbook,614-plus", "allwinner,sun5i-a13";
> +
> + aliases {
> + serial0 = &uart1;
> + i2c0 = &i2c0;
> + i2c1 = &i2c1;
> + i2c2 = &i2c2;
> + rtc0 = &pcf8563;
Please drop aliases except serial0.
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&led_pins_pocketbook>;
Drop pinctrl nodes. GPIOs don't need them.
> +
> + led {
> + gpios = <&pio 4 8 GPIO_ACTIVE_LOW>; /* PE8 */
> + default-state = "on";
Add additional properties, like function and color.
> + };
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + autorepeat;
Why is autorepeat needed?
> + label = "GPIO Keys";
I guess label is self evident and not needed?
> + pinctrl-names = "default";
> + pinctrl-0 = <&pocketbook_btn_pins>;
Again, GPIOs don't need pinctrl nodes. I know that you specified pull up, but
please try without. Other boards have same design and it's not needed.
> +
> + key-right {
> + label = "Right";
> + linux,code = <KEY_NEXT>;
> + gpios = <&pio 6 9 GPIO_ACTIVE_LOW>; /* PG9 */
> + };
> +
> + key-left {
> + label = "Left";
> + linux,code = <KEY_PREVIOUS>;
> + gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 */
> + };
> + };
> +
> + reg_3v3_mmc0: regulator-mmc0 {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd-mmc0";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pocketbook_reg_mmc0_pins>;
again, pinctrl not needed.
> + gpio = <&pio 4 4 GPIO_ACTIVE_LOW>; /* PE4 */
> + vin-supply = <®_vcc3v3>;
> + };
> +};
> +
> +&cpu0 {
> + cpu-supply = <®_dcdc2>;
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + axp209: pmic@34 {
> + compatible = "x-powers,axp209";
> + reg = <0x34>;
> + interrupts = <0>;
> + };
> +};
> +
> +#include "axp209.dtsi"
> +
> +&i2c1 {
> + status = "okay";
> +
> + pcf8563: rtc@51 {
> + compatible = "nxp,pcf8563";
> + reg = <0x51>;
> + #clock-cells = <0>;
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +
> + /* Touchpanel is connected here. */
Any reason why don't you specify touch panel device here?
> +};
> +
> +&lradc {
> + vref-supply = <®_ldo2>;
> + status = "okay";
> +
> + button-300 {
> + label = "Down";
> + linux,code = <KEY_DOWN>;
> + channel = <0>;
> + voltage = <300000>;
> + };
> +
> + button-700 {
> + label = "Up";
> + linux,code = <KEY_UP>;
> + channel = <0>;
> + voltage = <700000>;
> + };
> +
> + button-1000 {
> + label = "Left";
> + linux,code = <KEY_LEFT>;
> + channel = <0>;
> + voltage = <1000000>;
> + };
> +
> + button-1200 {
> + label = "Menu";
> + linux,code = <KEY_MENU>;
> + channel = <0>;
> + voltage = <1200000>;
> + };
> +
> + button-1500 {
> + label = "Right";
> + linux,code = <KEY_RIGHT>;
> + channel = <0>;
> + voltage = <1500000>;
> + };
> +};
> +
> +&mmc0 {
> + vmmc-supply = <®_3v3_mmc0>;
> + bus-width = <4>;
> + cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
> + status = "okay";
> +};
> +
> +&mmc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc2_4bit_pc_pins>;
> + vmmc-supply = <®_vcc3v3>;
> + bus-width = <4>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +&otg_sram {
> + status = "okay";
> +};
> +
> +&pio {
> + led_pins_pocketbook: led-pin {
> + pins = "PE8";
> + function = "gpio_out";
> + };
> + pocketbook_btn_pins: btn-pins {
> + pins = "PG9", "PG10";
> + function = "gpio_in";
> + bias-pull-up;
> + };
> + pocketbook_reg_mmc0_pins: reg-mmc0-pins {
> + pins = "PE4";
> + function = "gpio_out";
> + };
> +};
Whole PIO node can be dropped.
Best regards,
Jernej
> +
> +®_dcdc2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-name = "vdd-cpu";
> +};
> +
> +®_dcdc3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-name = "vdd-int-dll";
> +};
> +
> +®_ldo1 {
> + regulator-name = "vdd-rtc";
> +};
> +
> +®_ldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-name = "avcc";
> +};
> +
> +®_ldo3 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-wifi";
> +};
> +
> +®_usb0_vbus {
> + status = "okay";
> + gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
> +};
> +
> +®_usb1_vbus {
> + gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart1_pg_pins>;
> + status = "okay";
> +};
> +
> +&usb_otg {
> + dr_mode = "otg";
> + status = "okay";
> +};
> +
> +&usb_power_supply {
> + status = "okay";
> +};
> +
> +&battery_power_supply {
> + status = "okay";
> +};
> +
> +&usbphy {
> + usb0_id_det-gpios = <&pio 6 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG2 */
> + usb0_vbus_det-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
> + usb0_vbus-supply = <®_usb0_vbus>;
> + usb1_vbus-supply = <®_usb1_vbus>;
> + status = "okay";
> +};
>
On Thu, Mar 14, 2024 at 06:14:48PM +0100, Jernej Škrabec wrote:
> Hi Denis!
>
> Dne četrtek, 14. marec 2024 ob 16:53:06 CET je Denis Burkov napisal(a):
> > What works:
> >
> > - Serial console
> > - mmc0, mmc2 (both microSD card slots on the board)
> > - All buttons (gpio and lradc based)
> > - Power LED
> > - PMIC
> > - RTC
> > - USB OTG/gadgets mode
> >
> > Signed-off-by: Denis Burkov <[email protected]>
> > ---
> > arch/arm/boot/dts/allwinner/Makefile | 2 +
> > .../sun5i-a13-pocketbook-614-plus.dts | 254 ++++++++++++++++++
> > 2 files changed, 256 insertions(+)
> > create mode 100644 arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
> >
> > diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile
> > index 2d26c3397f14..fe321865beed 100644
> > --- a/arch/arm/boot/dts/allwinner/Makefile
> > +++ b/arch/arm/boot/dts/allwinner/Makefile
> > @@ -61,6 +61,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
> > sun5i-a13-olinuxino.dtb \
> > sun5i-a13-olinuxino-micro.dtb \
> > sun5i-a13-pocketbook-touch-lux-3.dtb \
> > + sun5i-a13-pocketbook-614-plus.dtb \
> > sun5i-a13-q8-tablet.dtb \
> > sun5i-a13-utoo-p66.dtb \
> > sun5i-gr8-chip-pro.dtb \
> > @@ -82,6 +83,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
> > sun5i-a13-olinuxino.dtb \
> > sun5i-a13-olinuxino-micro.dtb \
> > sun5i-a13-pocketbook-touch-lux-3.dtb \
> > + sun5i-a13-pocketbook-614-plus.dtb \
> > sun5i-a13-q8-tablet.dtb \
> > sun5i-a13-utoo-p66.dtb \
> > sun5i-gr8-chip-pro.dtb \
>
> This merge artefact. Can you add patch before this one and remove duplicate definitions?
>
Sorry, I didn't quite understand. Should I remove the duplicate block in a separate commit? or enable this one?
> > diff --git a/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
> > new file mode 100644
> > index 000000000000..89898fa16ff7
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
> > @@ -0,0 +1,254 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Copyright 2024 Denis Burkov <[email protected]>
> > + */
> > +
> > +/dts-v1/;
> > +#include "sun5i-a13.dtsi"
> > +#include "sunxi-common-regulators.dtsi"
>
> Extra empty line here.
>
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +#include <dt-bindings/interrupt-controller/irq.h>
> > +
> > +/ {
> > + model = "PocketBook 614 Plus";
> > + compatible = "pocketbook,614-plus", "allwinner,sun5i-a13";
> > +
> > + aliases {
> > + serial0 = &uart1;
> > + i2c0 = &i2c0;
> > + i2c1 = &i2c1;
> > + i2c2 = &i2c2;
> > + rtc0 = &pcf8563;
>
> Please drop aliases except serial0.
>
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&led_pins_pocketbook>;
>
> Drop pinctrl nodes. GPIOs don't need them.
>
> > +
> > + led {
> > + gpios = <&pio 4 8 GPIO_ACTIVE_LOW>; /* PE8 */
> > + default-state = "on";
>
> Add additional properties, like function and color.
>
> > + };
> > + };
> > +
> > + gpio-keys {
> > + compatible = "gpio-keys";
> > + autorepeat;
>
> Why is autorepeat needed?
>
> > + label = "GPIO Keys";
>
> I guess label is self evident and not needed?
>
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pocketbook_btn_pins>;
>
> Again, GPIOs don't need pinctrl nodes. I know that you specified pull up, but
> please try without. Other boards have same design and it's not needed.
>
> > +
> > + key-right {
> > + label = "Right";
> > + linux,code = <KEY_NEXT>;
> > + gpios = <&pio 6 9 GPIO_ACTIVE_LOW>; /* PG9 */
> > + };
> > +
> > + key-left {
> > + label = "Left";
> > + linux,code = <KEY_PREVIOUS>;
> > + gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 */
> > + };
> > + };
> > +
> > + reg_3v3_mmc0: regulator-mmc0 {
> > + compatible = "regulator-fixed";
> > + regulator-name = "vdd-mmc0";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pocketbook_reg_mmc0_pins>;
>
> again, pinctrl not needed.
>
> > + gpio = <&pio 4 4 GPIO_ACTIVE_LOW>; /* PE4 */
> > + vin-supply = <®_vcc3v3>;
> > + };
> > +};
> > +
> > +&cpu0 {
> > + cpu-supply = <®_dcdc2>;
> > +};
> > +
> > +&ehci0 {
> > + status = "okay";
> > +};
> > +
> > +&i2c0 {
> > + status = "okay";
> > +
> > + axp209: pmic@34 {
> > + compatible = "x-powers,axp209";
> > + reg = <0x34>;
> > + interrupts = <0>;
> > + };
> > +};
> > +
> > +#include "axp209.dtsi"
> > +
> > +&i2c1 {
> > + status = "okay";
> > +
> > + pcf8563: rtc@51 {
> > + compatible = "nxp,pcf8563";
> > + reg = <0x51>;
> > + #clock-cells = <0>;
> > + };
> > +};
> > +
> > +&i2c2 {
> > + status = "okay";
> > +
> > + /* Touchpanel is connected here. */
>
> Any reason why don't you specify touch panel device here?
>
My mistake, I copied this node from another device. This device does not have a touchpanel at all.
> > +};
> > +
> > +&lradc {
> > + vref-supply = <®_ldo2>;
> > + status = "okay";
> > +
> > + button-300 {
> > + label = "Down";
> > + linux,code = <KEY_DOWN>;
> > + channel = <0>;
> > + voltage = <300000>;
> > + };
> > +
> > + button-700 {
> > + label = "Up";
> > + linux,code = <KEY_UP>;
> > + channel = <0>;
> > + voltage = <700000>;
> > + };
> > +
> > + button-1000 {
> > + label = "Left";
> > + linux,code = <KEY_LEFT>;
> > + channel = <0>;
> > + voltage = <1000000>;
> > + };
> > +
> > + button-1200 {
> > + label = "Menu";
> > + linux,code = <KEY_MENU>;
> > + channel = <0>;
> > + voltage = <1200000>;
> > + };
> > +
> > + button-1500 {
> > + label = "Right";
> > + linux,code = <KEY_RIGHT>;
> > + channel = <0>;
> > + voltage = <1500000>;
> > + };
> > +};
> > +
> > +&mmc0 {
> > + vmmc-supply = <®_3v3_mmc0>;
> > + bus-width = <4>;
> > + cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
> > + status = "okay";
> > +};
> > +
> > +&mmc2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&mmc2_4bit_pc_pins>;
> > + vmmc-supply = <®_vcc3v3>;
> > + bus-width = <4>;
> > + non-removable;
> > + status = "okay";
> > +};
> > +
> > +&ohci0 {
> > + status = "okay";
> > +};
> > +
> > +&otg_sram {
> > + status = "okay";
> > +};
> > +
> > +&pio {
> > + led_pins_pocketbook: led-pin {
> > + pins = "PE8";
> > + function = "gpio_out";
> > + };
> > + pocketbook_btn_pins: btn-pins {
> > + pins = "PG9", "PG10";
> > + function = "gpio_in";
> > + bias-pull-up;
> > + };
> > + pocketbook_reg_mmc0_pins: reg-mmc0-pins {
> > + pins = "PE4";
> > + function = "gpio_out";
> > + };
> > +};
>
> Whole PIO node can be dropped.
>
> Best regards,
> Jernej
>
> > +
> > +®_dcdc2 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1000000>;
> > + regulator-max-microvolt = <1500000>;
> > + regulator-name = "vdd-cpu";
> > +};
> > +
> > +®_dcdc3 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1000000>;
> > + regulator-max-microvolt = <1400000>;
> > + regulator-name = "vdd-int-dll";
> > +};
> > +
> > +®_ldo1 {
> > + regulator-name = "vdd-rtc";
> > +};
> > +
> > +®_ldo2 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <3000000>;
> > + regulator-max-microvolt = <3000000>;
> > + regulator-name = "avcc";
> > +};
> > +
> > +®_ldo3 {
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "vcc-wifi";
> > +};
> > +
> > +®_usb0_vbus {
> > + status = "okay";
> > + gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
> > +};
> > +
> > +®_usb1_vbus {
> > + gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart1_pg_pins>;
> > + status = "okay";
> > +};
> > +
> > +&usb_otg {
> > + dr_mode = "otg";
> > + status = "okay";
> > +};
> > +
> > +&usb_power_supply {
> > + status = "okay";
> > +};
> > +
> > +&battery_power_supply {
> > + status = "okay";
> > +};
> > +
> > +&usbphy {
> > + usb0_id_det-gpios = <&pio 6 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG2 */
> > + usb0_vbus_det-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
> > + usb0_vbus-supply = <®_usb0_vbus>;
> > + usb1_vbus-supply = <®_usb1_vbus>;
> > + status = "okay";
> > +};
> >
>
>
>
>
Yes, everything works without pincrtl. One guy told me that I need to specify pinctrl for each pin used.
Thanks for the review.
Best regards,
Denis
Dne četrtek, 14. marec 2024 ob 19:18:58 CET je [email protected] napisal(a):
> On Thu, Mar 14, 2024 at 06:14:48PM +0100, Jernej Škrabec wrote:
> > Hi Denis!
> >
> > Dne četrtek, 14. marec 2024 ob 16:53:06 CET je Denis Burkov napisal(a):
> > > What works:
> > >
> > > - Serial console
> > > - mmc0, mmc2 (both microSD card slots on the board)
> > > - All buttons (gpio and lradc based)
> > > - Power LED
> > > - PMIC
> > > - RTC
> > > - USB OTG/gadgets mode
> > >
> > > Signed-off-by: Denis Burkov <[email protected]>
> > > ---
> > > arch/arm/boot/dts/allwinner/Makefile | 2 +
> > > .../sun5i-a13-pocketbook-614-plus.dts | 254 ++++++++++++++++++
> > > 2 files changed, 256 insertions(+)
> > > create mode 100644 arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
> > >
> > > diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile
> > > index 2d26c3397f14..fe321865beed 100644
> > > --- a/arch/arm/boot/dts/allwinner/Makefile
> > > +++ b/arch/arm/boot/dts/allwinner/Makefile
> > > @@ -61,6 +61,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
> > > sun5i-a13-olinuxino.dtb \
> > > sun5i-a13-olinuxino-micro.dtb \
> > > sun5i-a13-pocketbook-touch-lux-3.dtb \
> > > + sun5i-a13-pocketbook-614-plus.dtb \
> > > sun5i-a13-q8-tablet.dtb \
> > > sun5i-a13-utoo-p66.dtb \
> > > sun5i-gr8-chip-pro.dtb \
> > > @@ -82,6 +83,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
> > > sun5i-a13-olinuxino.dtb \
> > > sun5i-a13-olinuxino-micro.dtb \
> > > sun5i-a13-pocketbook-touch-lux-3.dtb \
> > > + sun5i-a13-pocketbook-614-plus.dtb \
> > > sun5i-a13-q8-tablet.dtb \
> > > sun5i-a13-utoo-p66.dtb \
> > > sun5i-gr8-chip-pro.dtb \
> >
> > This merge artefact. Can you add patch before this one and remove duplicate definitions?
> >
> Sorry, I didn't quite understand. Should I remove the duplicate block in a separate commit? or enable this one?
Yes, remove block in a separate patch, which should be positioned before this one.
> > > diff --git a/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
> > > new file mode 100644
> > > index 000000000000..89898fa16ff7
> > > --- /dev/null
> > > +++ b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
> > > @@ -0,0 +1,254 @@
> > > +// SPDX-License-Identifier: GPL-2.0+
> > > +/*
> > > + * Copyright 2024 Denis Burkov <[email protected]>
> > > + */
> > > +
> > > +/dts-v1/;
> > > +#include "sun5i-a13.dtsi"
> > > +#include "sunxi-common-regulators.dtsi"
> >
> > Extra empty line here.
> >
> > > +#include <dt-bindings/gpio/gpio.h>
> > > +#include <dt-bindings/input/input.h>
> > > +#include <dt-bindings/interrupt-controller/irq.h>
> > > +
> > > +/ {
> > > + model = "PocketBook 614 Plus";
> > > + compatible = "pocketbook,614-plus", "allwinner,sun5i-a13";
> > > +
> > > + aliases {
> > > + serial0 = &uart1;
> > > + i2c0 = &i2c0;
> > > + i2c1 = &i2c1;
> > > + i2c2 = &i2c2;
> > > + rtc0 = &pcf8563;
> >
> > Please drop aliases except serial0.
> >
> > > + };
> > > +
> > > + chosen {
> > > + stdout-path = "serial0:115200n8";
> > > + };
> > > +
> > > + leds {
> > > + compatible = "gpio-leds";
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&led_pins_pocketbook>;
> >
> > Drop pinctrl nodes. GPIOs don't need them.
> >
> > > +
> > > + led {
> > > + gpios = <&pio 4 8 GPIO_ACTIVE_LOW>; /* PE8 */
> > > + default-state = "on";
> >
> > Add additional properties, like function and color.
> >
> > > + };
> > > + };
> > > +
> > > + gpio-keys {
> > > + compatible = "gpio-keys";
> > > + autorepeat;
> >
> > Why is autorepeat needed?
> >
> > > + label = "GPIO Keys";
> >
> > I guess label is self evident and not needed?
> >
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pocketbook_btn_pins>;
> >
> > Again, GPIOs don't need pinctrl nodes. I know that you specified pull up, but
> > please try without. Other boards have same design and it's not needed.
> >
> > > +
> > > + key-right {
> > > + label = "Right";
> > > + linux,code = <KEY_NEXT>;
> > > + gpios = <&pio 6 9 GPIO_ACTIVE_LOW>; /* PG9 */
> > > + };
> > > +
> > > + key-left {
> > > + label = "Left";
> > > + linux,code = <KEY_PREVIOUS>;
> > > + gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 */
> > > + };
> > > + };
> > > +
> > > + reg_3v3_mmc0: regulator-mmc0 {
> > > + compatible = "regulator-fixed";
> > > + regulator-name = "vdd-mmc0";
> > > + regulator-min-microvolt = <3300000>;
> > > + regulator-max-microvolt = <3300000>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&pocketbook_reg_mmc0_pins>;
> >
> > again, pinctrl not needed.
> >
> > > + gpio = <&pio 4 4 GPIO_ACTIVE_LOW>; /* PE4 */
> > > + vin-supply = <®_vcc3v3>;
> > > + };
> > > +};
> > > +
> > > +&cpu0 {
> > > + cpu-supply = <®_dcdc2>;
> > > +};
> > > +
> > > +&ehci0 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&i2c0 {
> > > + status = "okay";
> > > +
> > > + axp209: pmic@34 {
> > > + compatible = "x-powers,axp209";
> > > + reg = <0x34>;
> > > + interrupts = <0>;
> > > + };
> > > +};
> > > +
> > > +#include "axp209.dtsi"
> > > +
> > > +&i2c1 {
> > > + status = "okay";
> > > +
> > > + pcf8563: rtc@51 {
> > > + compatible = "nxp,pcf8563";
> > > + reg = <0x51>;
> > > + #clock-cells = <0>;
> > > + };
> > > +};
> > > +
> > > +&i2c2 {
> > > + status = "okay";
> > > +
> > > + /* Touchpanel is connected here. */
> >
> > Any reason why don't you specify touch panel device here?
> >
> My mistake, I copied this node from another device. This device does not have a touchpanel at all.
> > > +};
> > > +
> > > +&lradc {
> > > + vref-supply = <®_ldo2>;
> > > + status = "okay";
> > > +
> > > + button-300 {
> > > + label = "Down";
> > > + linux,code = <KEY_DOWN>;
> > > + channel = <0>;
> > > + voltage = <300000>;
> > > + };
> > > +
> > > + button-700 {
> > > + label = "Up";
> > > + linux,code = <KEY_UP>;
> > > + channel = <0>;
> > > + voltage = <700000>;
> > > + };
> > > +
> > > + button-1000 {
> > > + label = "Left";
> > > + linux,code = <KEY_LEFT>;
> > > + channel = <0>;
> > > + voltage = <1000000>;
> > > + };
> > > +
> > > + button-1200 {
> > > + label = "Menu";
> > > + linux,code = <KEY_MENU>;
> > > + channel = <0>;
> > > + voltage = <1200000>;
> > > + };
> > > +
> > > + button-1500 {
> > > + label = "Right";
> > > + linux,code = <KEY_RIGHT>;
> > > + channel = <0>;
> > > + voltage = <1500000>;
> > > + };
> > > +};
> > > +
> > > +&mmc0 {
> > > + vmmc-supply = <®_3v3_mmc0>;
> > > + bus-width = <4>;
> > > + cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
> > > + status = "okay";
> > > +};
> > > +
> > > +&mmc2 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&mmc2_4bit_pc_pins>;
> > > + vmmc-supply = <®_vcc3v3>;
> > > + bus-width = <4>;
> > > + non-removable;
> > > + status = "okay";
> > > +};
> > > +
> > > +&ohci0 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&otg_sram {
> > > + status = "okay";
> > > +};
> > > +
> > > +&pio {
> > > + led_pins_pocketbook: led-pin {
> > > + pins = "PE8";
> > > + function = "gpio_out";
> > > + };
> > > + pocketbook_btn_pins: btn-pins {
> > > + pins = "PG9", "PG10";
> > > + function = "gpio_in";
> > > + bias-pull-up;
> > > + };
> > > + pocketbook_reg_mmc0_pins: reg-mmc0-pins {
> > > + pins = "PE4";
> > > + function = "gpio_out";
> > > + };
> > > +};
> >
> > Whole PIO node can be dropped.
> >
> > Best regards,
> > Jernej
> >
> > > +
> > > +®_dcdc2 {
> > > + regulator-always-on;
> > > + regulator-min-microvolt = <1000000>;
> > > + regulator-max-microvolt = <1500000>;
> > > + regulator-name = "vdd-cpu";
> > > +};
> > > +
> > > +®_dcdc3 {
> > > + regulator-always-on;
> > > + regulator-min-microvolt = <1000000>;
> > > + regulator-max-microvolt = <1400000>;
> > > + regulator-name = "vdd-int-dll";
> > > +};
> > > +
> > > +®_ldo1 {
> > > + regulator-name = "vdd-rtc";
> > > +};
> > > +
> > > +®_ldo2 {
> > > + regulator-always-on;
> > > + regulator-min-microvolt = <3000000>;
> > > + regulator-max-microvolt = <3000000>;
> > > + regulator-name = "avcc";
> > > +};
> > > +
> > > +®_ldo3 {
> > > + regulator-min-microvolt = <3300000>;
> > > + regulator-max-microvolt = <3300000>;
> > > + regulator-name = "vcc-wifi";
> > > +};
> > > +
> > > +®_usb0_vbus {
> > > + status = "okay";
> > > + gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
> > > +};
> > > +
> > > +®_usb1_vbus {
> > > + gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
> > > + status = "okay";
> > > +};
> > > +
> > > +&uart1 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&uart1_pg_pins>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&usb_otg {
> > > + dr_mode = "otg";
> > > + status = "okay";
> > > +};
> > > +
> > > +&usb_power_supply {
> > > + status = "okay";
> > > +};
> > > +
> > > +&battery_power_supply {
> > > + status = "okay";
> > > +};
> > > +
> > > +&usbphy {
> > > + usb0_id_det-gpios = <&pio 6 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG2 */
I missed this before, but is pull up property really needed? It doesn't make
much sense.
> > > + usb0_vbus_det-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
> > > + usb0_vbus-supply = <®_usb0_vbus>;
> > > + usb1_vbus-supply = <®_usb1_vbus>;
> > > + status = "okay";
> > > +};
> > >
> >
> >
> >
> >
> Yes, everything works without pincrtl. One guy told me that I need to specify pinctrl for each pin used.
pinctrl node is only needed when multiplexed pin is used for something else than GPIO.
Best regards,
Jernej
> Thanks for the review.
> Best regards,
> Denis
>
On Thu, 14 Mar 2024 20:53:05 +0500, Denis Burkov wrote:
> Add a new board name.
>
> Signed-off-by: Denis Burkov <[email protected]>
> ---
> Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
> 1 file changed, 5 insertions(+)
>
Acked-by: Rob Herring <[email protected]>
What works:
- Serial console
- mmc0, mmc2 (both microSD card slots on the board)
- All buttons (gpio and lradc based)
- Power LED
- PMIC
- RTC
- USB OTG/gadgets mode
Signed-off-by: Denis Burkov <[email protected]>
---
arch/arm/boot/dts/allwinner/Makefile | 1 +
.../sun5i-a13-pocketbook-614-plus.dts | 215 ++++++++++++++++++
2 files changed, 216 insertions(+)
create mode 100644 arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile
index 5fbb44ddacd0..6209243ad975 100644
--- a/arch/arm/boot/dts/allwinner/Makefile
+++ b/arch/arm/boot/dts/allwinner/Makefile
@@ -61,6 +61,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
sun5i-a13-olinuxino.dtb \
sun5i-a13-olinuxino-micro.dtb \
sun5i-a13-pocketbook-touch-lux-3.dtb \
+ sun5i-a13-pocketbook-614-plus.dtb \
sun5i-a13-q8-tablet.dtb \
sun5i-a13-utoo-p66.dtb \
sun5i-gr8-chip-pro.dtb \
diff --git a/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
new file mode 100644
index 000000000000..b5449301789a
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2024 Denis Burkov <[email protected]>
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "PocketBook 614 Plus";
+ compatible = "pocketbook,614-plus", "allwinner,sun5i-a13";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led {
+ gpios = <&pio 4 8 GPIO_ACTIVE_LOW>; /* PE8 */
+ default-state = "on";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ key-right {
+ label = "Right";
+ linux,code = <KEY_NEXT>;
+ gpios = <&pio 6 9 GPIO_ACTIVE_LOW>; /* PG9 */
+ };
+
+ key-left {
+ label = "Left";
+ linux,code = <KEY_PREVIOUS>;
+ gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 */
+ };
+ };
+
+ reg_3v3_mmc0: regulator-mmc0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-mmc0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 4 4 GPIO_ACTIVE_LOW>; /* PE4 */
+ vin-supply = <®_vcc3v3>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupts = <0>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&i2c1 {
+ status = "okay";
+
+ pcf8563: rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ };
+};
+
+&lradc {
+ vref-supply = <®_ldo2>;
+ status = "okay";
+
+ button-300 {
+ label = "Down";
+ linux,code = <KEY_DOWN>;
+ channel = <0>;
+ voltage = <300000>;
+ };
+
+ button-700 {
+ label = "Up";
+ linux,code = <KEY_UP>;
+ channel = <0>;
+ voltage = <700000>;
+ };
+
+ button-1000 {
+ label = "Left";
+ linux,code = <KEY_LEFT>;
+ channel = <0>;
+ voltage = <1000000>;
+ };
+
+ button-1200 {
+ label = "Menu";
+ linux,code = <KEY_MENU>;
+ channel = <0>;
+ voltage = <1200000>;
+ };
+
+ button-1500 {
+ label = "Right";
+ linux,code = <KEY_RIGHT>;
+ channel = <0>;
+ voltage = <1500000>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <®_3v3_mmc0>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_4bit_pc_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb0_vbus {
+ status = "okay";
+ gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+};
+
+®_usb1_vbus {
+ gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pg_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&battery_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+ usb0_vbus_det-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
--
2.43.0
Hi Denis!
Before I review, please resend this series properly. It shouldn't be sent as
response to old series, but as a new thread. Also, it has to be complete, in
this case with first patch, with review/ack tags where applicable.
Best regards,
Jernej
Dne sobota, 16. marec 2024 ob 15:39:18 CET je Denis Burkov napisal(a):
> What works:
>
> - Serial console
> - mmc0, mmc2 (both microSD card slots on the board)
> - All buttons (gpio and lradc based)
> - Power LED
> - PMIC
> - RTC
> - USB OTG/gadgets mode
>
> Signed-off-by: Denis Burkov <[email protected]>
> ---
> arch/arm/boot/dts/allwinner/Makefile | 1 +
> .../sun5i-a13-pocketbook-614-plus.dts | 215 ++++++++++++++++++
> 2 files changed, 216 insertions(+)
> create mode 100644 arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
>
> diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile
> index 5fbb44ddacd0..6209243ad975 100644
> --- a/arch/arm/boot/dts/allwinner/Makefile
> +++ b/arch/arm/boot/dts/allwinner/Makefile
> @@ -61,6 +61,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
> sun5i-a13-olinuxino.dtb \
> sun5i-a13-olinuxino-micro.dtb \
> sun5i-a13-pocketbook-touch-lux-3.dtb \
> + sun5i-a13-pocketbook-614-plus.dtb \
> sun5i-a13-q8-tablet.dtb \
> sun5i-a13-utoo-p66.dtb \
> sun5i-gr8-chip-pro.dtb \
> diff --git a/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
> new file mode 100644
> index 000000000000..b5449301789a
> --- /dev/null
> +++ b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
> @@ -0,0 +1,215 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright 2024 Denis Burkov <[email protected]>
> + */
> +
> +/dts-v1/;
> +#include "sun5i-a13.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> + model = "PocketBook 614 Plus";
> + compatible = "pocketbook,614-plus", "allwinner,sun5i-a13";
> +
> + aliases {
> + serial0 = &uart1;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led {
> + gpios = <&pio 4 8 GPIO_ACTIVE_LOW>; /* PE8 */
> + default-state = "on";
> + };
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> +
> + key-right {
> + label = "Right";
> + linux,code = <KEY_NEXT>;
> + gpios = <&pio 6 9 GPIO_ACTIVE_LOW>; /* PG9 */
> + };
> +
> + key-left {
> + label = "Left";
> + linux,code = <KEY_PREVIOUS>;
> + gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 */
> + };
> + };
> +
> + reg_3v3_mmc0: regulator-mmc0 {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd-mmc0";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&pio 4 4 GPIO_ACTIVE_LOW>; /* PE4 */
> + vin-supply = <®_vcc3v3>;
> + };
> +};
> +
> +&cpu0 {
> + cpu-supply = <®_dcdc2>;
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + axp209: pmic@34 {
> + compatible = "x-powers,axp209";
> + reg = <0x34>;
> + interrupts = <0>;
> + };
> +};
> +
> +#include "axp209.dtsi"
> +
> +&i2c1 {
> + status = "okay";
> +
> + pcf8563: rtc@51 {
> + compatible = "nxp,pcf8563";
> + reg = <0x51>;
> + #clock-cells = <0>;
> + };
> +};
> +
> +&lradc {
> + vref-supply = <®_ldo2>;
> + status = "okay";
> +
> + button-300 {
> + label = "Down";
> + linux,code = <KEY_DOWN>;
> + channel = <0>;
> + voltage = <300000>;
> + };
> +
> + button-700 {
> + label = "Up";
> + linux,code = <KEY_UP>;
> + channel = <0>;
> + voltage = <700000>;
> + };
> +
> + button-1000 {
> + label = "Left";
> + linux,code = <KEY_LEFT>;
> + channel = <0>;
> + voltage = <1000000>;
> + };
> +
> + button-1200 {
> + label = "Menu";
> + linux,code = <KEY_MENU>;
> + channel = <0>;
> + voltage = <1200000>;
> + };
> +
> + button-1500 {
> + label = "Right";
> + linux,code = <KEY_RIGHT>;
> + channel = <0>;
> + voltage = <1500000>;
> + };
> +};
> +
> +&mmc0 {
> + vmmc-supply = <®_3v3_mmc0>;
> + bus-width = <4>;
> + cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
> + status = "okay";
> +};
> +
> +&mmc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc2_4bit_pc_pins>;
> + vmmc-supply = <®_vcc3v3>;
> + bus-width = <4>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +&otg_sram {
> + status = "okay";
> +};
> +
> +®_dcdc2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-name = "vdd-cpu";
> +};
> +
> +®_dcdc3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-name = "vdd-int-dll";
> +};
> +
> +®_ldo1 {
> + regulator-name = "vdd-rtc";
> +};
> +
> +®_ldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-name = "avcc";
> +};
> +
> +®_usb0_vbus {
> + status = "okay";
> + gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
> +};
> +
> +®_usb1_vbus {
> + gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart1_pg_pins>;
> + status = "okay";
> +};
> +
> +&usb_otg {
> + dr_mode = "otg";
> + status = "okay";
> +};
> +
> +&usb_power_supply {
> + status = "okay";
> +};
> +
> +&battery_power_supply {
> + status = "okay";
> +};
> +
> +&usbphy {
> + usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
> + usb0_vbus_det-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
> + usb0_vbus-supply = <®_usb0_vbus>;
> + usb1_vbus-supply = <®_usb1_vbus>;
> + status = "okay";
> +};
>