Hi,
v11 patch including:
1) Patch mfd include header file.
2) mfd coding style.
3) add back wbuf description in dts.
v10 patch including:
1) Address range for > 64M byte flash.
2) Removed dirmap_write due to WBUF 256 bytes transfer issue.
3) Dummy bytes setting according to spi-nor.c layer.
v9 patch is for RPC MFD driver and RPC SPI driver.
v8 patch including:
1) Supported SoC-specific values in DTS.
2) Rename device node name as flash.
v7 patch is according to Geert and Sergei's comments:
1) Add all R-Car Gen3 model in dts.
2) patch rpc-if child node search.
3) minror coding style.
v6 patch is accroding to Geert, Marek and Sergei's comments:
1) spi_controller for new code.
2) "renesas,rcar-gen3-rpc" instead of "renesas,r8a77995-rpc."
3) patch external address read mode w/o u64 readq().
4) patch dts for write buffer & drop "renesas,rpc-mode".
5) coding style and so on.
v5 patch is accroding to Sergei's comments:
1) Read 6 bytes ID from Sergei's patch.
2) regmap_update_bits().
3) C++ style comment.
v4 patch is according to Sergei's comments including:
1) Drop soc_device_match().
2) Drop unused RPC registers.
3) Use ilog2() instead of fls().
4) Patch read 6 bytes ID w/ one command.
5) Coding style and so on.
v3 patch is according to Marek and Geert's comments including:
1) soc_device_mach() to set up RPC_PHYCNT_STRTIM.
2) get_unaligned().
3) rpc-mode for rpi-spi-flash or rpc-hyperflash.
4) coding style and so on.
v2 patch including:
1) remove RPC clock enable/dis-able control,
2) patch run time PM.
3) add RPC module software reset,
4) add regmap.
5) other coding style and so on.
thanks for your review.
best regards,
Mason
Mason Yang (3):
mfd: Add Renesas R-Car Gen3 RPC-IF MFD driver
spi: Add Renesas R-Car Gen3 RPC-IF SPI controller driver
dt-bindings: mfd: Document Renesas R-Car Gen3 RPC-IF MFD bindings
.../devicetree/bindings/mfd/mfd-renesas-rpc.txt | 39 ++
drivers/mfd/Kconfig | 9 +
drivers/mfd/Makefile | 1 +
drivers/mfd/renesas-rpc.c | 125 +++++
drivers/spi/Kconfig | 6 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-renesas-rpc.c | 571 +++++++++++++++++++++
include/linux/mfd/renesas-rpc.h | 141 +++++
8 files changed, 893 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/mfd-renesas-rpc.txt
create mode 100644 drivers/mfd/renesas-rpc.c
create mode 100644 drivers/spi/spi-renesas-rpc.c
create mode 100644 include/linux/mfd/renesas-rpc.h
--
1.9.1
Document the bindings used by the Renesas R-Car Gen3 RPC-IF MFD.
Signed-off-by: Mason Yang <[email protected]>
---
.../devicetree/bindings/mfd/mfd-renesas-rpc.txt | 39 ++++++++++++++++++++++
1 file changed, 39 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/mfd-renesas-rpc.txt
diff --git a/Documentation/devicetree/bindings/mfd/mfd-renesas-rpc.txt b/Documentation/devicetree/bindings/mfd/mfd-renesas-rpc.txt
new file mode 100644
index 0000000..ee3bad8
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/mfd-renesas-rpc.txt
@@ -0,0 +1,39 @@
+Renesas R-Car Gen3 RPC-IF MFD controller Device Tree Bindings
+-------------------------------------------------------------
+
+Required properties:
+- compatible: should be an SoC-specific compatible value, followed by
+ "renesas,rcar-gen3-rpc" as a fallback.
+ supported SoC-specific values are:
+ "renesas,r8a77995-rpc" (R-Car D3)
+- reg: should contain three register areas:
+ first for the base address of rpc-if registers,
+ second for the direct mapping read mode and
+ third for the write buffer area.
+- reg-names: should contain "regs", "dirmap" and "wbuf"
+- clocks: should contain 1 entries for the module's clock
+- clock-names: should contain "rpc"
+- #address-cells: should be 1
+- #size-cells: should be 0
+
+Example:
+
+ rpc: rpc-if@ee200000 {
+ compatible = "renesas,r8a77995-rpc", "renesas,rcar-gen3-rpc";
+ reg = <0 0xee200000 0 0x200>, <0 0x08000000 0 0x4000000>;
+ reg-names = "regs", "dirmap";
+ clocks = <&cpg CPG_MOD 917>;
+ clock-names = "rpc";
+ power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+ resets = <&cpg 917>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <1>;
+ };
+ };
--
1.9.1
Add a driver for Renesas R-Car Gen3 RPC-IF SPI controller.
Signed-off-by: Mason Yang <[email protected]>
Signed-off-by: Sergei Shtylyov <[email protected]>
---
drivers/spi/Kconfig | 6 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-renesas-rpc.c | 571 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 578 insertions(+)
create mode 100644 drivers/spi/spi-renesas-rpc.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index f761655..1f52bcf 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -564,6 +564,12 @@ config SPI_RSPI
help
SPI driver for Renesas RSPI and QSPI blocks.
+config SPI_RENESAS_RPC
+ tristate "Renesas R-Car Gen3 RPC-IF controller"
+ depends on ARCH_RENESAS || COMPILE_TEST
+ help
+ SPI driver for Renesas R-Car Gen3 RPC-IF.
+
config SPI_QCOM_QSPI
tristate "QTI QSPI controller"
depends on ARCH_QCOM
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index d8fc03c..b3a3deb 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -86,6 +86,7 @@ obj-$(CONFIG_SPI_QUP) += spi-qup.o
obj-$(CONFIG_SPI_ROCKCHIP) += spi-rockchip.o
obj-$(CONFIG_SPI_RB4XX) += spi-rb4xx.o
obj-$(CONFIG_SPI_RSPI) += spi-rspi.o
+obj-$(CONFIG_SPI_RENESAS_RPC) += spi-renesas-rpc.o
obj-$(CONFIG_SPI_S3C24XX) += spi-s3c24xx-hw.o
spi-s3c24xx-hw-y := spi-s3c24xx.o
spi-s3c24xx-hw-$(CONFIG_SPI_S3C24XX_FIQ) += spi-s3c24xx-fiq.o
diff --git a/drivers/spi/spi-renesas-rpc.c b/drivers/spi/spi-renesas-rpc.c
new file mode 100644
index 0000000..634222d
--- /dev/null
+++ b/drivers/spi/spi-renesas-rpc.c
@@ -0,0 +1,571 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2018 ~ 2019 Renesas Solutions Corp.
+// Copyright (C) 2019 Macronix International Co., Ltd.
+//
+// R-Car Gen3 RPC-IF SPI/QSPI/Octa driver
+//
+// Author:
+// Mason Yang <[email protected]>
+//
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/log2.h>
+#include <linux/iopoll.h>
+#include <linux/mfd/renesas-rpc.h>
+#include <linux/module.h>
+#include <linux/mtd/mtd.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi-mem.h>
+
+#include <asm/unaligned.h>
+
+struct rpc_spi {
+ struct rpc_mfd *mfd;
+ u32 cur_speed_hz;
+ u32 cmd;
+ u32 addr;
+ u32 dummy;
+ u32 smcr;
+ u32 smenr;
+ u32 xferlen;
+ u32 totalxferlen;
+ enum spi_mem_data_dir xfer_dir;
+};
+
+static int rpc_spi_set_freq(struct rpc_spi *rpc, unsigned long freq)
+{
+ int ret;
+
+ if (rpc->cur_speed_hz == freq)
+ return 0;
+
+ ret = clk_set_rate(rpc->mfd->clk_rpc, freq);
+ if (ret)
+ return ret;
+
+ rpc->cur_speed_hz = freq;
+ return ret;
+}
+
+static void rpc_spi_hw_init(struct rpc_spi *rpc)
+{
+ //
+ // NOTE: The 0x260 are undocumented bits, but they must be set.
+ // RPC_PHYCNT_STRTIM is strobe timing adjustment bit,
+ // 0x0 : the delay is biggest,
+ // 0x1 : the delay is 2nd biggest,
+ // On H3 ES1.x, the value should be 0, while on others,
+ // the value should be 6.
+ //
+ regmap_write(rpc->mfd->regmap, RPC_PHYCNT, RPC_PHYCNT_CAL |
+ RPC_PHYCNT_STRTIM(6) | 0x260);
+
+ //
+ // NOTE: The 0x1511144 are undocumented bits, but they must be set
+ // for RPC_PHYOFFSET1.
+ // The 0x31 are undocumented bits, but they must be set
+ // for RPC_PHYOFFSET2.
+ //
+ regmap_write(rpc->mfd->regmap, RPC_PHYOFFSET1,
+ RPC_PHYOFFSET1_DDRTMG(3) | 0x1511144);
+ regmap_write(rpc->mfd->regmap, RPC_PHYOFFSET2, 0x31 |
+ RPC_PHYOFFSET2_OCTTMG(4));
+ regmap_write(rpc->mfd->regmap, RPC_SSLDR, RPC_SSLDR_SPNDL(7) |
+ RPC_SSLDR_SLNDL(7) | RPC_SSLDR_SCKDL(7));
+ regmap_write(rpc->mfd->regmap, RPC_CMNCR, RPC_CMNCR_MD |
+ RPC_CMNCR_SFDE | RPC_CMNCR_MOIIO_HIZ | RPC_CMNCR_IOFV_HIZ |
+ RPC_CMNCR_BSZ(0));
+}
+
+static int wait_msg_xfer_end(struct rpc_spi *rpc)
+{
+ u32 sts;
+
+ return regmap_read_poll_timeout(rpc->mfd->regmap, RPC_CMNSR, sts,
+ sts & RPC_CMNSR_TEND, 0, USEC_PER_SEC);
+}
+
+static u8 rpc_bits_set(u32 nbytes)
+{
+ nbytes = clamp(nbytes, 1U, 4U);
+
+ return GENMASK(3, 4 - nbytes);
+}
+
+static int rpc_spi_io_xfer(struct rpc_spi *rpc,
+ const void *tx_buf, void *rx_buf)
+{
+ u32 smenr, smcr, data, pos = 0;
+ int ret;
+
+ regmap_update_bits(rpc->mfd->regmap, RPC_CMNCR, RPC_CMNCR_MD,
+ RPC_CMNCR_MD);
+ regmap_write(rpc->mfd->regmap, RPC_SMDRENR, 0);
+ regmap_write(rpc->mfd->regmap, RPC_SMCMR, rpc->cmd);
+ regmap_write(rpc->mfd->regmap, RPC_SMDMCR, rpc->dummy);
+ regmap_write(rpc->mfd->regmap, RPC_SMADR, rpc->addr);
+ smenr = rpc->smenr;
+
+ if (tx_buf) {
+ while (pos < rpc->xferlen) {
+ u32 nbytes = rpc->xferlen - pos;
+
+ regmap_write(rpc->mfd->regmap, RPC_SMWDR0,
+ get_unaligned((u32 *)(tx_buf + pos)));
+
+ smcr = rpc->smcr | RPC_SMCR_SPIE;
+
+ if (nbytes > 4) {
+ nbytes = 4;
+ smcr |= RPC_SMCR_SSLKP;
+ }
+
+ regmap_write(rpc->mfd->regmap, RPC_SMENR, smenr);
+ regmap_write(rpc->mfd->regmap, RPC_SMCR, smcr);
+ ret = wait_msg_xfer_end(rpc);
+ if (ret)
+ goto err_out;
+
+ pos += nbytes;
+ smenr = rpc->smenr & ~RPC_SMENR_CDE &
+ ~RPC_SMENR_ADE(0xf);
+ }
+ } else if (rx_buf) {
+ //
+ // RPC-IF spoils the data for the commands without an address
+ // phase (like RDID) in the manual mode, so we'll have to work
+ // around this issue by using the external address space read
+ // mode instead.
+ //
+ if (!(smenr & RPC_SMENR_ADE(0xf)) && rpc->mfd->dirmap) {
+ regmap_update_bits(rpc->mfd->regmap, RPC_CMNCR,
+ RPC_CMNCR_MD, 0);
+ regmap_write(rpc->mfd->regmap, RPC_DRCR,
+ RPC_DRCR_RBURST(32) | RPC_DRCR_RBE);
+ regmap_write(rpc->mfd->regmap, RPC_DREAR,
+ RPC_DREAR_EAC(1));
+ regmap_write(rpc->mfd->regmap, RPC_DRCMR, rpc->cmd);
+ regmap_write(rpc->mfd->regmap, RPC_DRDMCR, rpc->dummy);
+ regmap_write(rpc->mfd->regmap, RPC_DROPR, 0);
+ regmap_write(rpc->mfd->regmap, RPC_DRENR, smenr);
+ memcpy_fromio(rx_buf, rpc->mfd->dirmap, rpc->xferlen);
+ regmap_write(rpc->mfd->regmap, RPC_DRCR, RPC_DRCR_RCF);
+ } else {
+ while (pos < rpc->xferlen) {
+ u32 nbytes = rpc->xferlen - pos;
+
+ if (nbytes > 4)
+ nbytes = 4;
+
+ regmap_write(rpc->mfd->regmap, RPC_SMENR,
+ smenr);
+ regmap_write(rpc->mfd->regmap, RPC_SMCR,
+ rpc->smcr | RPC_SMCR_SPIE);
+ ret = wait_msg_xfer_end(rpc);
+ if (ret)
+ goto err_out;
+
+ regmap_read(rpc->mfd->regmap, RPC_SMRDR0,
+ &data);
+ memcpy(rx_buf + pos, &data, nbytes);
+ pos += nbytes;
+
+ regmap_write(rpc->mfd->regmap, RPC_SMADR,
+ rpc->addr + pos);
+ }
+ }
+ } else {
+ regmap_write(rpc->mfd->regmap, RPC_SMENR, rpc->smenr);
+ regmap_write(rpc->mfd->regmap, RPC_SMCR,
+ rpc->smcr | RPC_SMCR_SPIE);
+ ret = wait_msg_xfer_end(rpc);
+ if (ret)
+ goto err_out;
+ }
+
+ return 0;
+
+err_out:
+ return reset_control_reset(rpc->mfd->rstc);
+}
+
+static void rpc_spi_mem_set_prep_op_cfg(struct spi_device *spi,
+ const struct spi_mem_op *op,
+ u64 *offs, size_t *len)
+{
+ struct rpc_spi *rpc = spi_controller_get_devdata(spi->controller);
+
+ rpc->cmd = RPC_SMCMR_CMD(op->cmd.opcode);
+ rpc->smenr = RPC_SMENR_CDE |
+ RPC_SMENR_CDB(ilog2(op->cmd.buswidth));
+ rpc->totalxferlen = 1;
+ rpc->xfer_dir = SPI_MEM_NO_DATA;
+ rpc->xferlen = 0;
+ rpc->addr = 0;
+
+ if (op->addr.nbytes) {
+ rpc->smenr |= RPC_SMENR_ADB(ilog2(op->addr.buswidth));
+ if (op->addr.nbytes == 4)
+ rpc->smenr |= RPC_SMENR_ADE(0xf);
+ else
+ rpc->smenr |= RPC_SMENR_ADE(0x7);
+
+ if (offs && len)
+ rpc->addr = *offs;
+ else
+ rpc->addr = op->addr.val;
+ rpc->totalxferlen += op->addr.nbytes;
+ }
+
+ if (op->dummy.nbytes) {
+ rpc->smenr |= RPC_SMENR_DME;
+ rpc->dummy = RPC_SMDMCR_DMCYC(op->dummy.nbytes * 8 /
+ op->dummy.buswidth);
+ rpc->totalxferlen += op->dummy.nbytes;
+ }
+
+ if (op->data.nbytes || (offs && len)) {
+ switch (op->data.dir) {
+ case SPI_MEM_DATA_IN:
+ rpc->smcr = RPC_SMCR_SPIRE;
+ rpc->xfer_dir = SPI_MEM_DATA_IN;
+ break;
+ case SPI_MEM_DATA_OUT:
+ rpc->smcr = RPC_SMCR_SPIWE;
+ rpc->xfer_dir = SPI_MEM_DATA_OUT;
+ break;
+ default:
+ break;
+ }
+
+ if (offs && len) {
+ rpc->smenr |= RPC_SMENR_SPIDE(rpc_bits_set(*len)) |
+ RPC_SMENR_SPIDB(ilog2(op->data.buswidth));
+ rpc->xferlen = *len;
+ rpc->totalxferlen += *len;
+ } else {
+ rpc->smenr |=
+ RPC_SMENR_SPIDE(rpc_bits_set(op->data.nbytes)) |
+ RPC_SMENR_SPIDB(ilog2(op->data.buswidth));
+ rpc->xferlen = op->data.nbytes;
+ rpc->totalxferlen += op->data.nbytes;
+ }
+ }
+}
+
+static bool rpc_spi_mem_supports_op(struct spi_mem *mem,
+ const struct spi_mem_op *op)
+{
+ if (op->data.buswidth > 4 || op->addr.buswidth > 4 ||
+ op->dummy.buswidth > 4 || op->cmd.buswidth > 4 ||
+ op->addr.nbytes > 4)
+ return false;
+
+ return true;
+}
+
+static ssize_t rpc_spi_mem_dirmap_read(struct spi_mem_dirmap_desc *desc,
+ u64 offs, size_t len, void *buf)
+{
+ struct rpc_spi *rpc =
+ spi_controller_get_devdata(desc->mem->spi->controller);
+ loff_t from = offs & (RPC_DIRMAP_SIZE - 1);
+ size_t size = RPC_DIRMAP_SIZE - from;
+ int ret;
+
+ if (offs + desc->info.offset + len > U32_MAX)
+ return -EINVAL;
+
+ if (len > size)
+ len = size;
+
+ ret = rpc_spi_set_freq(rpc, desc->mem->spi->max_speed_hz);
+ if (ret)
+ return ret;
+
+ rpc_spi_mem_set_prep_op_cfg(desc->mem->spi,
+ &desc->info.op_tmpl, &offs, &len);
+
+ regmap_update_bits(rpc->mfd->regmap, RPC_CMNCR, RPC_CMNCR_MD, 0);
+ regmap_write(rpc->mfd->regmap, RPC_DRCR, RPC_DRCR_RBURST(32) |
+ RPC_DRCR_RBE);
+
+ regmap_write(rpc->mfd->regmap, RPC_DRCMR, rpc->cmd);
+ regmap_write(rpc->mfd->regmap, RPC_DREAR,
+ RPC_DREAR_EAV(offs >> 25) | RPC_DREAR_EAC(1));
+ regmap_write(rpc->mfd->regmap, RPC_DROPR, 0);
+ regmap_write(rpc->mfd->regmap, RPC_DRENR, rpc->smenr);
+ regmap_write(rpc->mfd->regmap, RPC_DRDMCR, rpc->dummy);
+ regmap_write(rpc->mfd->regmap, RPC_DRDRENR, 0);
+
+ memcpy_fromio(buf, rpc->mfd->dirmap + desc->info.offset + from, len);
+
+ return len;
+}
+
+static int rpc_spi_mem_dirmap_create(struct spi_mem_dirmap_desc *desc)
+{
+ struct rpc_spi *rpc =
+ spi_controller_get_devdata(desc->mem->spi->controller);
+
+ if (desc->info.offset + desc->info.length > U32_MAX)
+ return -ENOTSUPP;
+
+ if (!rpc_spi_mem_supports_op(desc->mem, &desc->info.op_tmpl))
+ return -ENOTSUPP;
+
+ if (!rpc->mfd->dirmap &&
+ desc->info.op_tmpl.data.dir == SPI_MEM_DATA_IN)
+ return -ENOTSUPP;
+
+ if (desc->info.op_tmpl.data.dir == SPI_MEM_DATA_OUT)
+ return -ENOTSUPP;
+
+ return 0;
+}
+
+static int rpc_spi_mem_exec_op(struct spi_mem *mem,
+ const struct spi_mem_op *op)
+{
+ struct rpc_spi *rpc = spi_controller_get_devdata(mem->spi->controller);
+ int ret;
+
+ ret = rpc_spi_set_freq(rpc, mem->spi->max_speed_hz);
+ if (ret)
+ return ret;
+
+ rpc_spi_mem_set_prep_op_cfg(mem->spi, op, NULL, NULL);
+
+ ret = rpc_spi_io_xfer(rpc,
+ op->data.dir == SPI_MEM_DATA_OUT ?
+ op->data.buf.out : NULL,
+ op->data.dir == SPI_MEM_DATA_IN ?
+ op->data.buf.in : NULL);
+
+ return ret;
+}
+
+static const struct spi_controller_mem_ops rpc_spi_mem_ops = {
+ .supports_op = rpc_spi_mem_supports_op,
+ .exec_op = rpc_spi_mem_exec_op,
+ .dirmap_create = rpc_spi_mem_dirmap_create,
+ .dirmap_read = rpc_spi_mem_dirmap_read,
+};
+
+static void rpc_spi_transfer_setup(struct rpc_spi *rpc,
+ struct spi_message *msg)
+{
+ struct spi_transfer *t, xfer[4] = { };
+ u32 i, xfercnt, xferpos = 0;
+
+ rpc->totalxferlen = 0;
+ rpc->xfer_dir = SPI_MEM_NO_DATA;
+
+ list_for_each_entry(t, &msg->transfers, transfer_list) {
+ if (t->tx_buf) {
+ xfer[xferpos].tx_buf = t->tx_buf;
+ xfer[xferpos].tx_nbits = t->tx_nbits;
+ }
+
+ if (t->rx_buf) {
+ xfer[xferpos].rx_buf = t->rx_buf;
+ xfer[xferpos].rx_nbits = t->rx_nbits;
+ }
+
+ if (t->len) {
+ xfer[xferpos++].len = t->len;
+ rpc->totalxferlen += t->len;
+ }
+
+ if (list_is_last(&t->transfer_list, &msg->transfers)) {
+ if (xferpos > 1) {
+ if (t->rx_buf) {
+ rpc->xfer_dir = SPI_MEM_DATA_IN;
+ rpc->smcr = RPC_SMCR_SPIRE;
+ } else if (t->tx_buf) {
+ rpc->xfer_dir = SPI_MEM_DATA_OUT;
+ rpc->smcr = RPC_SMCR_SPIWE;
+ }
+ }
+ }
+ }
+
+ xfercnt = xferpos;
+ rpc->xferlen = xfer[--xferpos].len;
+ rpc->cmd = RPC_SMCMR_CMD(((u8 *)xfer[0].tx_buf)[0]);
+ rpc->smenr = RPC_SMENR_CDE |
+ RPC_SMENR_CDB(ilog2((unsigned int)xfer[0].tx_nbits));
+ rpc->addr = 0;
+
+ if (xfercnt > 2 && xfer[1].len && xfer[1].tx_buf) {
+ rpc->smenr |=
+ RPC_SMENR_ADB(ilog2((unsigned int)xfer[1].tx_nbits));
+
+ for (i = 0; i < xfer[1].len; i++)
+ rpc->addr |= ((u8 *)xfer[1].tx_buf)[i] <<
+ (8 * (xfer[1].len - i - 1));
+
+ if (xfer[1].len == 4)
+ rpc->smenr |= RPC_SMENR_ADE(0xf);
+ else
+ rpc->smenr |= RPC_SMENR_ADE(0x7);
+ }
+
+ if (xfercnt > 3 && xfer[2].len && xfer[2].tx_buf) {
+ rpc->smenr |= RPC_SMENR_DME;
+ rpc->dummy = RPC_SMDMCR_DMCYC(xfer[2].len * 8 /
+ xfer[2].tx_nbits);
+ }
+
+ for (i = xfercnt - 1; i < xfercnt && xfercnt > 1; i++) {
+ if (xfer[i].rx_buf) {
+ rpc->smenr |=
+ RPC_SMENR_SPIDE(rpc_bits_set(xfer[i].len)) |
+ RPC_SMENR_SPIDB(ilog2
+ ((unsigned int)xfer[i].rx_nbits));
+ } else if (xfer[i].tx_buf) {
+ rpc->smenr |=
+ RPC_SMENR_SPIDE(rpc_bits_set(xfer[i].len)) |
+ RPC_SMENR_SPIDB(ilog2
+ ((unsigned int)xfer[i].tx_nbits));
+ }
+ }
+}
+
+static inline int rpc_spi_xfer_message(struct rpc_spi *rpc,
+ struct spi_transfer *data_xfer)
+{
+ int ret;
+
+ ret = rpc_spi_set_freq(rpc, data_xfer->speed_hz);
+ if (ret)
+ return ret;
+
+ ret = rpc_spi_io_xfer(rpc,
+ rpc->xfer_dir == SPI_MEM_DATA_OUT ?
+ data_xfer->tx_buf : NULL,
+ rpc->xfer_dir == SPI_MEM_DATA_IN ?
+ data_xfer->rx_buf : NULL);
+
+ return ret;
+}
+
+static int rpc_spi_transfer_one_message(struct spi_controller *ctlr,
+ struct spi_message *msg)
+{
+ struct rpc_spi *rpc = spi_controller_get_devdata(ctlr);
+ struct spi_transfer *data_xfer;
+ int ret;
+
+ rpc_spi_transfer_setup(rpc, msg);
+
+ data_xfer = list_last_entry(&msg->transfers, struct spi_transfer,
+ transfer_list);
+
+ ret = rpc_spi_xfer_message(rpc, data_xfer);
+ if (ret)
+ goto out;
+
+ msg->status = 0;
+ msg->actual_length = rpc->totalxferlen;
+out:
+ spi_finalize_current_message(ctlr);
+ return 0;
+}
+
+static int rpc_spi_probe(struct platform_device *pdev)
+{
+ struct spi_controller *ctlr;
+ struct rpc_mfd *rpc_mfd = dev_get_drvdata(pdev->dev.parent);
+ struct rpc_spi *rpc;
+ int ret;
+
+ ctlr = spi_alloc_master(&pdev->dev, sizeof(*rpc));
+ if (!ctlr)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, ctlr);
+
+ rpc = spi_controller_get_devdata(ctlr);
+
+ rpc->mfd = rpc_mfd;
+ ctlr->dev.of_node = pdev->dev.parent->of_node;
+
+ pm_runtime_enable(&pdev->dev);
+ ctlr->auto_runtime_pm = true;
+
+ ctlr->num_chipselect = 1;
+ ctlr->mem_ops = &rpc_spi_mem_ops;
+ ctlr->transfer_one_message = rpc_spi_transfer_one_message;
+
+ ctlr->bits_per_word_mask = SPI_BPW_MASK(8);
+ ctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_TX_QUAD | SPI_RX_QUAD;
+
+ pm_runtime_get_sync(&pdev->dev);
+ rpc_spi_hw_init(rpc);
+ pm_runtime_put(&pdev->dev);
+
+ ret = spi_register_controller(ctlr);
+ if (ret) {
+ dev_err(&pdev->dev, "spi_register_controller failed\n");
+ goto err_put_ctlr;
+ }
+
+ return 0;
+err_put_ctlr:
+ spi_controller_put(ctlr);
+ pm_runtime_disable(&pdev->dev);
+
+ return ret;
+}
+
+static int rpc_spi_remove(struct platform_device *pdev)
+{
+ struct spi_controller *ctlr = platform_get_drvdata(pdev);
+
+ pm_runtime_disable(&pdev->dev);
+ spi_unregister_controller(ctlr);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int rpc_spi_suspend(struct device *dev)
+{
+ struct spi_controller *ctlr = dev_get_drvdata(dev);
+
+ return spi_controller_suspend(ctlr);
+}
+
+static int rpc_spi_resume(struct device *dev)
+{
+ struct spi_controller *ctlr = dev_get_drvdata(dev);
+
+ return spi_controller_resume(ctlr);
+}
+
+static SIMPLE_DEV_PM_OPS(rpc_spi_pm_ops, rpc_spi_suspend, rpc_spi_resume);
+#define DEV_PM_OPS (&rpc_spi_pm_ops)
+#else
+#define DEV_PM_OPS NULL
+#endif
+
+static struct platform_driver rpc_spi_driver = {
+ .probe = rpc_spi_probe,
+ .remove = rpc_spi_remove,
+ .driver = {
+ .name = "rpc-spi",
+ .pm = DEV_PM_OPS,
+ },
+};
+module_platform_driver(rpc_spi_driver);
+
+MODULE_AUTHOR("Mason Yang <[email protected]>");
+MODULE_DESCRIPTION("Renesas R-Car Gen3 RPC-IF SPI controller driver");
+MODULE_LICENSE("GPL v2");
--
1.9.1
Add a driver for Renesas R-Car Gen3 RPC-IF MFD.
Signed-off-by: Mason Yang <[email protected]>
---
drivers/mfd/Kconfig | 9 +++
drivers/mfd/Makefile | 1 +
drivers/mfd/renesas-rpc.c | 125 +++++++++++++++++++++++++++++++++++
include/linux/mfd/renesas-rpc.h | 141 ++++++++++++++++++++++++++++++++++++++++
4 files changed, 276 insertions(+)
create mode 100644 drivers/mfd/renesas-rpc.c
create mode 100644 include/linux/mfd/renesas-rpc.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 26ad646..efdb1b9 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -978,6 +978,15 @@ config MFD_RDC321X
southbridge which provides access to GPIOs and Watchdog using the
southbridge PCI device configuration space.
+config MFD_RENESAS_RPC
+ tristate "Renesas R-Car Gen3 RPC-IF MFD driver"
+ select MFD_CORE
+ depends on ARCH_RENESAS
+ help
+ This supports Renesas R-Car Gen3 RPC-IF multifunction device
+ which provides either SPI host or HyperFlash.
+ You have to select individual components under the corresponding menu.
+
config MFD_RT5033
tristate "Richtek RT5033 Power Management IC"
depends on I2C
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index b4569ed7..4a49699 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -183,6 +183,7 @@ obj-$(CONFIG_MFD_INTEL_QUARK_I2C_GPIO) += intel_quark_i2c_gpio.o
obj-$(CONFIG_LPC_SCH) += lpc_sch.o
obj-$(CONFIG_LPC_ICH) += lpc_ich.o
obj-$(CONFIG_MFD_RDC321X) += rdc321x-southbridge.o
+obj-$(CONFIG_MFD_RENESAS_RPC) += renesas-rpc.o
obj-$(CONFIG_MFD_JANZ_CMODIO) += janz-cmodio.o
obj-$(CONFIG_MFD_JZ4740_ADC) += jz4740-adc.o
obj-$(CONFIG_MFD_TPS6586X) += tps6586x.o
diff --git a/drivers/mfd/renesas-rpc.c b/drivers/mfd/renesas-rpc.c
new file mode 100644
index 0000000..c80c8d1
--- /dev/null
+++ b/drivers/mfd/renesas-rpc.c
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2018 ~ 2019 Renesas Solutions Corp.
+// Copyright (C) 2019 Macronix International Co., Ltd.
+//
+// R-Car Gen3 RPC-IF MFD driver
+//
+// Author:
+// Mason Yang <[email protected]>
+//
+
+#include <linux/clk.h>
+#include <linux/mfd/core.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+#include <linux/mfd/renesas-rpc.h>
+#include <linux/reset.h>
+
+static const struct mfd_cell rpc_hf_ctlr = {
+ .name = "rpc-hf",
+};
+
+static const struct mfd_cell rpc_spi_ctlr = {
+ .name = "rpc-spi",
+};
+
+static const struct regmap_range rpc_mfd_volatile_ranges[] = {
+ regmap_reg_range(RPC_SMRDR0, RPC_SMRDR1),
+ regmap_reg_range(RPC_SMWDR0, RPC_SMWDR1),
+ regmap_reg_range(RPC_CMNSR, RPC_CMNSR),
+};
+
+static const struct regmap_access_table rpc_mfd_volatile_table = {
+ .yes_ranges = rpc_mfd_volatile_ranges,
+ .n_yes_ranges = ARRAY_SIZE(rpc_mfd_volatile_ranges),
+};
+
+static const struct regmap_config rpc_mfd_regmap_config = {
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+ .fast_io = true,
+ .max_register = RPC_PHYOFFSET2,
+ .volatile_table = &rpc_mfd_volatile_table,
+};
+
+static int rpc_mfd_probe(struct platform_device *pdev)
+{
+ struct device_node *flash;
+ const struct mfd_cell *cell;
+ struct resource *res;
+ struct rpc_mfd *rpc;
+ void __iomem *base;
+
+ flash = of_get_next_child(pdev->dev.of_node, NULL);
+ if (!flash) {
+ dev_warn(&pdev->dev, "no flash node found\n");
+ return -ENODEV;
+ }
+
+ if (of_device_is_compatible(flash, "jedec,spi-nor")) {
+ cell = &rpc_spi_ctlr;
+ } else if (of_device_is_compatible(flash, "cfi-flash")) {
+ cell = &rpc_hf_ctlr;
+ } else {
+ dev_warn(&pdev->dev, "unknown flash type\n");
+ return -ENODEV;
+ }
+
+ rpc = devm_kzalloc(&pdev->dev, sizeof(*rpc), GFP_KERNEL);
+ if (!rpc)
+ return -ENOMEM;
+
+ rpc->clk_rpc = devm_clk_get(&pdev->dev, "rpc");
+ if (IS_ERR(rpc->clk_rpc))
+ return PTR_ERR(rpc->clk_rpc);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "regs");
+ base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ rpc->regmap = devm_regmap_init_mmio(&pdev->dev, base,
+ &rpc_mfd_regmap_config);
+ if (IS_ERR(rpc->regmap)) {
+ dev_err(&pdev->dev,
+ "failed to init regmap for rpc-mfd, error %ld\n",
+ PTR_ERR(rpc->regmap));
+ return PTR_ERR(rpc->regmap);
+ }
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dirmap");
+ rpc->dirmap = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(rpc->dirmap))
+ rpc->dirmap = NULL;
+
+ rpc->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
+ if (IS_ERR(rpc->rstc))
+ return PTR_ERR(rpc->rstc);
+
+ platform_set_drvdata(pdev, rpc);
+
+ return devm_mfd_add_devices(&pdev->dev, -1, cell, 1, NULL, 0, NULL);
+}
+
+static const struct of_device_id rpc_mfd_of_match[] = {
+ { .compatible = "renesas,rcar-gen3-rpc", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, rpc_mfd_of_match);
+
+static struct platform_driver rpc_mfd_driver = {
+ .probe = rpc_mfd_probe,
+ .driver = {
+ .name = "rpc-mfd",
+ .of_match_table = rpc_mfd_of_match,
+ },
+};
+module_platform_driver(rpc_mfd_driver);
+
+MODULE_AUTHOR("Mason Yang <[email protected]>");
+MODULE_DESCRIPTION("Renesas R-Car Gen3 RPC MFD driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/renesas-rpc.h b/include/linux/mfd/renesas-rpc.h
new file mode 100644
index 0000000..bc53d02
--- /dev/null
+++ b/include/linux/mfd/renesas-rpc.h
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2018 ~ 2019 Renesas Solutions Corp.
+// Copyright (C) 2019 Macronix International Co., Ltd.
+//
+// R-Car Gen3 RPC-IF MFD driver
+//
+// Author:
+// Mason Yang <[email protected]>
+//
+
+#ifndef __MFD_RENESAS_RPC_H
+#define __MFD_RENESAS_RPC_H
+
+#define RPC_CMNCR 0x0000 // R/W
+#define RPC_CMNCR_MD BIT(31)
+#define RPC_CMNCR_SFDE BIT(24) // undocumented bit but must be set
+#define RPC_CMNCR_MOIIO3(val) (((val) & 0x3) << 22)
+#define RPC_CMNCR_MOIIO2(val) (((val) & 0x3) << 20)
+#define RPC_CMNCR_MOIIO1(val) (((val) & 0x3) << 18)
+#define RPC_CMNCR_MOIIO0(val) (((val) & 0x3) << 16)
+#define RPC_CMNCR_MOIIO_HIZ (RPC_CMNCR_MOIIO0(3) | RPC_CMNCR_MOIIO1(3) | \
+ RPC_CMNCR_MOIIO2(3) | RPC_CMNCR_MOIIO3(3))
+#define RPC_CMNCR_IO3FV(val) (((val) & 0x3) << 14) // undocumented
+#define RPC_CMNCR_IO2FV(val) (((val) & 0x3) << 12) // undocumented
+#define RPC_CMNCR_IO0FV(val) (((val) & 0x3) << 8)
+#define RPC_CMNCR_IOFV_HIZ (RPC_CMNCR_IO0FV(3) | RPC_CMNCR_IO2FV(3) | \
+ RPC_CMNCR_IO3FV(3))
+#define RPC_CMNCR_BSZ(val) (((val) & 0x3) << 0)
+
+#define RPC_SSLDR 0x0004 // R/W
+#define RPC_SSLDR_SPNDL(d) (((d) & 0x7) << 16)
+#define RPC_SSLDR_SLNDL(d) (((d) & 0x7) << 8)
+#define RPC_SSLDR_SCKDL(d) (((d) & 0x7) << 0)
+
+#define RPC_DRCR 0x000C // R/W
+#define RPC_DRCR_SSLN BIT(24)
+#define RPC_DRCR_RBURST(v) ((((v) - 1) & 0x1F) << 16)
+#define RPC_DRCR_RCF BIT(9)
+#define RPC_DRCR_RBE BIT(8)
+#define RPC_DRCR_SSLE BIT(0)
+
+#define RPC_DRCMR 0x0010 // R/W
+#define RPC_DRCMR_CMD(c) (((c) & 0xFF) << 16)
+#define RPC_DRCMR_OCMD(c) (((c) & 0xFF) << 0)
+
+#define RPC_DREAR 0x0014 // R/W
+#define RPC_DREAR_EAV(c) (((c) & 0xf) << 16)
+#define RPC_DREAR_EAC(c) (((c) & 0x7) << 0)
+
+#define RPC_DROPR 0x0018 // R/W
+
+#define RPC_DRENR 0x001C // R/W
+#define RPC_DRENR_CDB(o) (u32)((((o) & 0x3) << 30))
+#define RPC_DRENR_OCDB(o) (((o) & 0x3) << 28)
+#define RPC_DRENR_ADB(o) (((o) & 0x3) << 24)
+#define RPC_DRENR_OPDB(o) (((o) & 0x3) << 20)
+#define RPC_DRENR_DRDB(o) (((o) & 0x3) << 16)
+#define RPC_DRENR_DME BIT(15)
+#define RPC_DRENR_CDE BIT(14)
+#define RPC_DRENR_OCDE BIT(12)
+#define RPC_DRENR_ADE(v) (((v) & 0xF) << 8)
+#define RPC_DRENR_OPDE(v) (((v) & 0xF) << 4)
+
+#define RPC_SMCR 0x0020 // R/W
+#define RPC_SMCR_SSLKP BIT(8)
+#define RPC_SMCR_SPIRE BIT(2)
+#define RPC_SMCR_SPIWE BIT(1)
+#define RPC_SMCR_SPIE BIT(0)
+
+#define RPC_SMCMR 0x0024 // R/W
+#define RPC_SMCMR_CMD(c) (((c) & 0xFF) << 16)
+#define RPC_SMCMR_OCMD(c) (((c) & 0xFF) << 0)
+
+#define RPC_SMADR 0x0028 // R/W
+#define RPC_SMOPR 0x002C // R/W
+#define RPC_SMOPR_OPD3(o) (((o) & 0xFF) << 24)
+#define RPC_SMOPR_OPD2(o) (((o) & 0xFF) << 16)
+#define RPC_SMOPR_OPD1(o) (((o) & 0xFF) << 8)
+#define RPC_SMOPR_OPD0(o) (((o) & 0xFF) << 0)
+
+#define RPC_SMENR 0x0030 // R/W
+#define RPC_SMENR_CDB(o) (((o) & 0x3) << 30)
+#define RPC_SMENR_OCDB(o) (((o) & 0x3) << 28)
+#define RPC_SMENR_ADB(o) (((o) & 0x3) << 24)
+#define RPC_SMENR_OPDB(o) (((o) & 0x3) << 20)
+#define RPC_SMENR_SPIDB(o) (((o) & 0x3) << 16)
+#define RPC_SMENR_DME BIT(15)
+#define RPC_SMENR_CDE BIT(14)
+#define RPC_SMENR_OCDE BIT(12)
+#define RPC_SMENR_ADE(v) (((v) & 0xF) << 8)
+#define RPC_SMENR_OPDE(v) (((v) & 0xF) << 4)
+#define RPC_SMENR_SPIDE(v) (((v) & 0xF) << 0)
+
+#define RPC_SMRDR0 0x0038 // R
+#define RPC_SMRDR1 0x003C // R
+#define RPC_SMWDR0 0x0040 // W
+#define RPC_SMWDR1 0x0044 // W
+
+#define RPC_CMNSR 0x0048 // R
+#define RPC_CMNSR_SSLF BIT(1)
+#define RPC_CMNSR_TEND BIT(0)
+
+#define RPC_DRDMCR 0x0058 // R/W
+#define RPC_DRDRENR 0x005C // R/W
+
+#define RPC_SMDMCR 0x0060 // R/W
+#define RPC_SMDMCR_DMCYC(v) ((((v) - 1) & 0x1F) << 0)
+
+#define RPC_SMDRENR 0x0064 // R/W
+#define RPC_SMDRENR_HYPE (0x7 << 12)
+#define RPC_SMDRENR_ADDRE BIT(8)
+#define RPC_SMDRENR_OPDRE BIT(4)
+#define RPC_SMDRENR_SPIDRE BIT(0)
+
+#define RPC_PHYCNT 0x007C // R/W
+#define RPC_PHYCNT_CAL BIT(31)
+#define PRC_PHYCNT_OCTA_AA BIT(22)
+#define PRC_PHYCNT_OCTA_SA BIT(23)
+#define PRC_PHYCNT_EXDS BIT(21)
+#define RPC_PHYCNT_OCT BIT(20)
+#define RPC_PHYCNT_STRTIM(v) (((v) & 0x7) << 15)
+#define RPC_PHYCNT_WBUF2 BIT(4)
+#define RPC_PHYCNT_WBUF BIT(2)
+#define RPC_PHYCNT_PHYMEM(v) (((v) & 0x3) << 0)
+
+#define RPC_PHYOFFSET1 0x0080 // R/W
+#define RPC_PHYOFFSET1_DDRTMG(v) (((v) & 0x3) << 28)
+#define RPC_PHYOFFSET2 0x0084 // R/W
+#define RPC_PHYOFFSET2_OCTTMG(v) (((v) & 0x7) << 8)
+
+#define RPC_DIRMAP_SIZE 0x4000000
+
+struct rpc_mfd {
+ struct clk *clk_rpc;
+ void __iomem *dirmap;
+ struct regmap *regmap;
+ struct reset_control *rstc;
+};
+
+#endif // __MFD_RENESAS_RPC_H
--
1.9.1
Hello!
On 04/22/2019 06:32 AM, Mason Yang wrote:
> Document the bindings used by the Renesas R-Car Gen3 RPC-IF MFD.
>
> Signed-off-by: Mason Yang <[email protected]>
> ---
> .../devicetree/bindings/mfd/mfd-renesas-rpc.txt | 39 ++++++++++++++++++++++
> 1 file changed, 39 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/mfd-renesas-rpc.txt
>
> diff --git a/Documentation/devicetree/bindings/mfd/mfd-renesas-rpc.txt b/Documentation/devicetree/bindings/mfd/mfd-renesas-rpc.txt
> new file mode 100644
> index 0000000..ee3bad8
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/mfd-renesas-rpc.txt
> @@ -0,0 +1,39 @@
> +Renesas R-Car Gen3 RPC-IF MFD controller Device Tree Bindings
> +-------------------------------------------------------------
> +
> +Required properties:
> +- compatible: should be an SoC-specific compatible value, followed by
> + "renesas,rcar-gen3-rpc" as a fallback.
> + supported SoC-specific values are:
> + "renesas,r8a77995-rpc" (R-Car D3)
> +- reg: should contain three register areas:
> + first for the base address of rpc-if registers,
RPC-IF.
> + second for the direct mapping read mode and
> + third for the write buffer area.
> +- reg-names: should contain "regs", "dirmap" and "wbuf"
> +- clocks: should contain 1 entries for the module's clock
> +- clock-names: should contain "rpc"
> +- #address-cells: should be 1
> +- #size-cells: should be 0
> +
> +Example:
> +
> + rpc: rpc-if@ee200000 {
> + compatible = "renesas,r8a77995-rpc", "renesas,rcar-gen3-rpc";
> + reg = <0 0xee200000 0 0x200>, <0 0x08000000 0 0x4000000>;
> + reg-names = "regs", "dirmap";
You forgot to add back the "wbuf" entrees above.
> + clocks = <&cpg CPG_MOD 917>;
> + clock-names = "rpc";
> + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
> + resets = <&cpg 917>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <40000000>;
> + spi-tx-bus-width = <1>;
> + spi-rx-bus-width = <1>;
> + };
> + };
>
MBR, Sergei
On 04/22/2019 06:32 AM, Mason Yang wrote:
> Add a driver for Renesas R-Car Gen3 RPC-IF SPI controller.
>
> Signed-off-by: Mason Yang <[email protected]>
> Signed-off-by: Sergei Shtylyov <[email protected]>
[...]
Do dote that I'm opposed to the driver separation as it's presented in
this patches, and I have a large patch reworking both MFD and SPI drivers
in the works.
> diff --git a/drivers/spi/spi-renesas-rpc.c b/drivers/spi/spi-renesas-rpc.c
> new file mode 100644
> index 0000000..634222d
> --- /dev/null
> +++ b/drivers/spi/spi-renesas-rpc.c
> @@ -0,0 +1,571 @@
[...]
> +static int rpc_spi_probe(struct platform_device *pdev)
> +{
> + struct spi_controller *ctlr;
> + struct rpc_mfd *rpc_mfd = dev_get_drvdata(pdev->dev.parent);
> + struct rpc_spi *rpc;
> + int ret;
> +
> + ctlr = spi_alloc_master(&pdev->dev, sizeof(*rpc));
> + if (!ctlr)
> + return -ENOMEM;
> +
> + platform_set_drvdata(pdev, ctlr);
> +
> + rpc = spi_controller_get_devdata(ctlr);
> +
> + rpc->mfd = rpc_mfd;
> + ctlr->dev.of_node = pdev->dev.parent->of_node;
> +
> + pm_runtime_enable(&pdev->dev);
> + ctlr->auto_runtime_pm = true;
> +
> + ctlr->num_chipselect = 1;
> + ctlr->mem_ops = &rpc_spi_mem_ops;
> + ctlr->transfer_one_message = rpc_spi_transfer_one_message;
> +
> + ctlr->bits_per_word_mask = SPI_BPW_MASK(8);
> + ctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_TX_QUAD | SPI_RX_QUAD;
> +
> + pm_runtime_get_sync(&pdev->dev);
> + rpc_spi_hw_init(rpc);
> + pm_runtime_put(&pdev->dev);
> +
> + ret = spi_register_controller(ctlr);
> + if (ret) {
> + dev_err(&pdev->dev, "spi_register_controller failed\n");
> + goto err_put_ctlr;
> + }
> +
> + return 0;
Previous formatting was better, shouldn't have moved the empty line above
*return*...
> +err_put_ctlr:
> + spi_controller_put(ctlr);
> + pm_runtime_disable(&pdev->dev);
> +
> + return ret;
> +}
[...]
MBR, Sergei
On 04/22/2019 09:32 PM, Sergei Shtylyov wrote:
>> Add a driver for Renesas R-Car Gen3 RPC-IF SPI controller.
>>
>> Signed-off-by: Mason Yang <[email protected]>
>> Signed-off-by: Sergei Shtylyov <[email protected]>
> [...]
>
> Do dote that I'm opposed to the driver separation as it's presented in
Sorry, s/dote/note/.
> this patches, and I have a large patch reworking both MFD and SPI drivers
> in the works.
[...]
MBR, Sergei
On 04/23/2019 12:22 PM, [email protected] wrote:
>> > Add a driver for Renesas R-Car Gen3 RPC-IF SPI controller.
>> >
>> > Signed-off-by: Mason Yang <[email protected]>
>> > Signed-off-by: Sergei Shtylyov <[email protected]>
>> [...]
>>
>> Do dote that I'm opposed to the driver separation as it's presented in
>> this patches, and I have a large patch reworking both MFD and SPI drivers
>> in the works.
>>
>
> Do you mean add your name in both MFD & dt-binding ?
Of course not!
> i.e.,
> [PATCH v12 3/3] dt-bindings: mfd: Document Renesas R-Car Gen3 RPC-IF MFD bindings
>
> Document the bindings used by the Renesas R-Car Gen3 RPC-IF MFD.
>
> Signed-off-by: Mason Yang <[email protected]>
> Signed-off-by: Sergei Shtylyov <[email protected]>
>
>
>
> [PATCH v12 1/3] mfd: Add Renesas R-Car Gen3 RPC-IF MFD driver
>
> Add a driver for Renesas R-Car Gen3 RPC-IF MFD.
>
> Signed-off-by: Mason Yang <[email protected]>
> Signed-off-by: Sergei Shtylyov <[email protected]>
>
>
> Is it ok ?
I'm not OK with the most of the driver code ending up in the SPI driver,
I think most of the code should be kept in the MFD driver and just be called
by SPI/HF drivers.
> best regards,
> Mason
MBR, Sergei