This adds support for the BOE TH101MB31IG002 LCD Panel used in PineTab2 [1] and
PineTab-V [2] as well as the devictrees for the PineTab2 v0.1 and v2.0.
The BOE LCD Panel patch was retrieved from [3]. The function-name prefix has
been adapted and the LCD init section was simplified.
The PineTab2 devicetree patch was retrieved from [4]. Some renaming was needed
to pass the dtb-checks, the brightness-levels are specified as range and steps
instead of a list of values.
[5] and [6] was also used as source for this queue.
[1] https://wiki.pine64.org/wiki/PineTab2
[2] https://wiki.pine64.org/wiki/PineTab-V
[3] https://salsa.debian.org/Mobian-team/devices/kernels/rockchip-linux/-/blob/mobian-6.6/debian/patches/display/0018-drm-panel-add-BOE-TH101MB31IG002-28A-driver.patch?ref_type=heads
[4] https://salsa.debian.org/Mobian-team/devices/kernels/rockchip-linux/-/blob/mobian-6.6/debian/patches/device-tree/0134-arch-arm64-add-Pine64-PineTab2-device-trees.patch?ref_type=heads
[5] https://github.com/dreemurrs-embedded/linux-pinetab2/tree/v6.6.7-danctnix1
[6] https://xff.cz/git/linux?h=pt2-6.7
Signed-off-by: Manuel Traut <[email protected]>
---
Changes in v4:
- Rebased on v6.8-rc1
- BOE TH101MB31IG002 LCD Panel:
* Picked patches from https://anongit.freedesktop.org/git/drm/drm-misc.git (drm-misc-next)
- PineTab2 dts:
* Make flash-led a regulator-led and control the regulator by GPIO and set
V5_MIDU as vin-supply to ensure that LED is working even if all other
drivers using V5 MIDU are unloaded.
* Add -regulator suffix to nodes, replace -con suffix by -connector
* Set lcd pinctrl in .dts instead of .dtsi so it is more clear that this is
different between pinetab v0.1 and v2.0
* Remove unused bluetooth uart configuration and pinctrl
* Increase spi-nor max-speed from 24 to 100 MHz
- Link to v3: https://lore.kernel.org/r/[email protected]
Changes in v3:
- PineTab2 dts:
* Remove useless regulator-state-mem nodes for fixed regulators
* Swap mmc0 and mmc1, so mmc0 is now the internal eMMC
- BOE TH101MB31IG002 LCD Panel:
* Remove enabled/prepared checks since they are done in core.
- Use consistent naming (PineTab2 and PineTab-V) in commit messages.
- Link to v2: https://lore.kernel.org/r/[email protected]
Changes in v2:
- Removed dtb-checker fixups, cause I am not sure if they are correct
- Applied review comments for dt bindings
- pinetab2 dts:
* Remove unverified WLAN entries, as in [5]
* Simplify flash LED definition, as in [5]
* Fix headphone detection and sound routing, as in [5]
* Fix CRU clock configuration
- BOE TH101MB31IG002 LCD Panel:
* Reworked prepare/enable unprepare/disable, as in [5]
- Replaced nicknames by realnames in author and signed-offs
- Link to v1: https://lore.kernel.org/r/[email protected]
---
Alexander Warnecke (1):
drm/panel: Add driver for BOE TH101MB31IG002-28A panel
Manuel Traut (3):
dt-bindings: display: panel: Add BOE TH101MB31IG002-28A panel
dt-bindings: arm64: rockchip: Add Pine64 PineTab2
arm64: dts: rockchip: Add devicetree for Pine64 PineTab2
.../devicetree/bindings/arm/rockchip.yaml | 8 +
.../display/panel/boe,th101mb31ig002-28a.yaml | 58 ++
arch/arm64/boot/dts/rockchip/Makefile | 2 +
.../boot/dts/rockchip/rk3566-pinetab2-v0.1.dts | 28 +
.../boot/dts/rockchip/rk3566-pinetab2-v2.0.dts | 48 ++
arch/arm64/boot/dts/rockchip/rk3566-pinetab2.dtsi | 943 +++++++++++++++++++++
drivers/gpu/drm/panel/Kconfig | 11 +
drivers/gpu/drm/panel/Makefile | 1 +
.../gpu/drm/panel/panel-boe-th101mb31ig002-28a.c | 322 +++++++
9 files changed, 1421 insertions(+)
---
base-commit: 3a5879d495b226d0404098e3564462d5f1daa33b
change-id: 20231222-pinetab2-faa77e01db6f
Best regards,
--
Manuel Traut <[email protected]>
Add bindings for the BOE TH101MB31IG002-28A LCD panel. It is
used e.g. in the Pine64 PineTab2 and PineTab-V.
Signed-off-by: Manuel Traut <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit baae3a0b10c499d4228514a701602f6fd2a8d6b4)
---
.../display/panel/boe,th101mb31ig002-28a.yaml | 58 ++++++++++++++++++++++
1 file changed, 58 insertions(+)
diff --git a/Documentation/devicetree/bindings/display/panel/boe,th101mb31ig002-28a.yaml b/Documentation/devicetree/bindings/display/panel/boe,th101mb31ig002-28a.yaml
new file mode 100644
index 000000000000..32df26cbfeed
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/boe,th101mb31ig002-28a.yaml
@@ -0,0 +1,58 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/boe,th101mb31ig002-28a.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: BOE TH101MB31IG002-28A WXGA DSI Display Panel
+
+maintainers:
+ - Manuel Traut <[email protected]>
+
+allOf:
+ - $ref: panel-common.yaml#
+
+properties:
+ compatible:
+ enum:
+ # BOE TH101MB31IG002-28A 10.1" WXGA TFT LCD panel
+ - boe,th101mb31ig002-28a
+
+ reg: true
+ backlight: true
+ enable-gpios: true
+ power-supply: true
+ port: true
+ rotation: true
+
+required:
+ - compatible
+ - reg
+ - enable-gpios
+ - power-supply
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ dsi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ panel@0 {
+ compatible = "boe,th101mb31ig002-28a";
+ reg = <0>;
+ backlight = <&backlight_lcd0>;
+ enable-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>;
+ rotation = <90>;
+ power-supply = <&vcc_3v3>;
+ port {
+ panel_in_dsi: endpoint {
+ remote-endpoint = <&dsi_out_con>;
+ };
+ };
+ };
+ };
+
+...
--
2.43.0
Add devicvetree binding documentation for Pine64 PineTab2
which uses the Rockchip RK3566 SoC.
Signed-off-by: Manuel Traut <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
---
Documentation/devicetree/bindings/arm/rockchip.yaml | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 5cf5cbef2cf5..1b9740e2f3a1 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -650,6 +650,14 @@ properties:
- const: pine64,pinenote
- const: rockchip,rk3566
+ - description: Pine64 PineTab2
+ items:
+ - enum:
+ - pine64,pinetab2-v0.1
+ - pine64,pinetab2-v2.0
+ - const: pine64,pinetab2
+ - const: rockchip,rk3566
+
- description: Pine64 PinePhonePro
items:
- const: pine64,pinephone-pro
--
2.43.0
From: Alexander Warnecke <[email protected]>
The BOE TH101MB31IG002-28A panel is a WXGA panel.
It is used in Pine64 PineTab2 and PineTab-V.
Signed-off-by: Alexander Warnecke <[email protected]>
Signed-off-by: Manuel Traut <[email protected]>
Reviewed-by: Jessica Zhang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
(cherry picked from commit 420186db1483da4e16cd5d5a472f511a35dbc1b7)
---
drivers/gpu/drm/panel/Kconfig | 11 +
drivers/gpu/drm/panel/Makefile | 1 +
.../gpu/drm/panel/panel-boe-th101mb31ig002-28a.c | 322 +++++++++++++++++++++
3 files changed, 334 insertions(+)
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index 8f3783742208..00a947941c19 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -67,6 +67,17 @@ config DRM_PANEL_BOE_HIMAX8279D
24 bit RGB per pixel. It provides a MIPI DSI interface to
the host and has a built-in LED backlight.
+config DRM_PANEL_BOE_TH101MB31UIG002_28A
+ tristate "Boe TH101MB31UIG002-28A panel"
+ depends on OF
+ depends on DRM_MIPI_DSI
+ depends on BACKLIGHT_CLASS_DEVICE
+ help
+ Say Y here if you want to enable support for Boe
+ TH101MB31UIG002-28A TFT-LCD modules. The panel has a 800x1280
+ resolution and uses 24 bit RGB per pixel. It provides a MIPI DSI
+ interface to the host and has a built-in LED backlight.
+
config DRM_PANEL_BOE_TV101WUM_NL6
tristate "BOE TV101WUM and AUO KD101N80 45NA 1200x1920 panel"
depends on OF
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index d94a644d0a6c..015bb8d70fbd 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -5,6 +5,7 @@ obj-$(CONFIG_DRM_PANEL_ASUS_Z00T_TM5P5_NT35596) += panel-asus-z00t-tm5p5-n35596.
obj-$(CONFIG_DRM_PANEL_AUO_A030JTN01) += panel-auo-a030jtn01.o
obj-$(CONFIG_DRM_PANEL_BOE_BF060Y8M_AJ0) += panel-boe-bf060y8m-aj0.o
obj-$(CONFIG_DRM_PANEL_BOE_HIMAX8279D) += panel-boe-himax8279d.o
+obj-$(CONFIG_DRM_PANEL_BOE_TH101MB31UIG002_28A) += panel-boe-th101mb31ig002-28a.o
obj-$(CONFIG_DRM_PANEL_BOE_TV101WUM_NL6) += panel-boe-tv101wum-nl6.o
obj-$(CONFIG_DRM_PANEL_DSI_CM) += panel-dsi-cm.o
obj-$(CONFIG_DRM_PANEL_LVDS) += panel-lvds.o
diff --git a/drivers/gpu/drm/panel/panel-boe-th101mb31ig002-28a.c b/drivers/gpu/drm/panel/panel-boe-th101mb31ig002-28a.c
new file mode 100644
index 000000000000..763e9f8342d3
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-boe-th101mb31ig002-28a.c
@@ -0,0 +1,322 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2023 Alexander Warnecke <[email protected]>
+ * Copyright (c) 2023 Manuel Traut <[email protected]>
+ * Copyright (c) 2023 Dang Huynh <[email protected]>
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/regulator/consumer.h>
+
+#include <drm/drm_connector.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+
+struct boe_th101mb31ig002 {
+ struct drm_panel panel;
+
+ struct mipi_dsi_device *dsi;
+
+ struct regulator *power;
+ struct gpio_desc *enable;
+ struct gpio_desc *reset;
+
+ enum drm_panel_orientation orientation;
+};
+
+static void boe_th101mb31ig002_reset(struct boe_th101mb31ig002 *ctx)
+{
+ gpiod_direction_output(ctx->reset, 0);
+ usleep_range(10, 100);
+ gpiod_direction_output(ctx->reset, 1);
+ usleep_range(10, 100);
+ gpiod_direction_output(ctx->reset, 0);
+ usleep_range(5000, 6000);
+}
+
+static int boe_th101mb31ig002_enable(struct drm_panel *panel)
+{
+ struct boe_th101mb31ig002 *ctx = container_of(panel,
+ struct boe_th101mb31ig002,
+ panel);
+ struct mipi_dsi_device *dsi = ctx->dsi;
+ struct device *dev = &dsi->dev;
+ int ret;
+
+ mipi_dsi_dcs_write_seq(dsi, 0xE0, 0xAB, 0xBA);
+ mipi_dsi_dcs_write_seq(dsi, 0xE1, 0xBA, 0xAB);
+ mipi_dsi_dcs_write_seq(dsi, 0xB1, 0x10, 0x01, 0x47, 0xFF);
+ mipi_dsi_dcs_write_seq(dsi, 0xB2, 0x0C, 0x14, 0x04, 0x50, 0x50, 0x14);
+ mipi_dsi_dcs_write_seq(dsi, 0xB3, 0x56, 0x53, 0x00);
+ mipi_dsi_dcs_write_seq(dsi, 0xB4, 0x33, 0x30, 0x04);
+ mipi_dsi_dcs_write_seq(dsi, 0xB6, 0xB0, 0x00, 0x00, 0x10, 0x00, 0x10,
+ 0x00);
+ mipi_dsi_dcs_write_seq(dsi, 0xB8, 0x05, 0x12, 0x29, 0x49, 0x48, 0x00,
+ 0x00);
+ mipi_dsi_dcs_write_seq(dsi, 0xB9, 0x7C, 0x65, 0x55, 0x49, 0x46, 0x36,
+ 0x3B, 0x24, 0x3D, 0x3C, 0x3D, 0x5C, 0x4C,
+ 0x55, 0x47, 0x46, 0x39, 0x26, 0x06, 0x7C,
+ 0x65, 0x55, 0x49, 0x46, 0x36, 0x3B, 0x24,
+ 0x3D, 0x3C, 0x3D, 0x5C, 0x4C, 0x55, 0x47,
+ 0x46, 0x39, 0x26, 0x06);
+ mipi_dsi_dcs_write_seq(dsi, 0x00, 0xFF, 0x87, 0x12, 0x34, 0x44, 0x44,
+ 0x44, 0x44, 0x98, 0x04, 0x98, 0x04, 0x0F,
+ 0x00, 0x00, 0xC1);
+ mipi_dsi_dcs_write_seq(dsi, 0xC1, 0x54, 0x94, 0x02, 0x85, 0x9F, 0x00,
+ 0x7F, 0x00, 0x54, 0x00);
+ mipi_dsi_dcs_write_seq(dsi, 0xC2, 0x17, 0x09, 0x08, 0x89, 0x08, 0x11,
+ 0x22, 0x20, 0x44, 0xFF, 0x18, 0x00);
+ mipi_dsi_dcs_write_seq(dsi, 0xC3, 0x86, 0x46, 0x05, 0x05, 0x1C, 0x1C,
+ 0x1D, 0x1D, 0x02, 0x1F, 0x1F, 0x1E, 0x1E,
+ 0x0F, 0x0F, 0x0D, 0x0D, 0x13, 0x13, 0x11,
+ 0x11, 0x00);
+ mipi_dsi_dcs_write_seq(dsi, 0xC4, 0x07, 0x07, 0x04, 0x04, 0x1C, 0x1C,
+ 0x1D, 0x1D, 0x02, 0x1F, 0x1F, 0x1E, 0x1E,
+ 0x0E, 0x0E, 0x0C, 0x0C, 0x12, 0x12, 0x10,
+ 0x10, 0x00);
+ mipi_dsi_dcs_write_seq(dsi, 0xC6, 0x2A, 0x2A);
+ mipi_dsi_dcs_write_seq(dsi, 0xC8, 0x21, 0x00, 0x31, 0x42, 0x34, 0x16);
+ mipi_dsi_dcs_write_seq(dsi, 0xCA, 0xCB, 0x43);
+ mipi_dsi_dcs_write_seq(dsi, 0xCD, 0x0E, 0x4B, 0x4B, 0x20, 0x19, 0x6B,
+ 0x06, 0xB3);
+ mipi_dsi_dcs_write_seq(dsi, 0xD2, 0xE3, 0x2B, 0x38, 0x00);
+ mipi_dsi_dcs_write_seq(dsi, 0xD4, 0x00, 0x01, 0x00, 0x0E, 0x04, 0x44,
+ 0x08, 0x10, 0x00, 0x00, 0x00);
+ mipi_dsi_dcs_write_seq(dsi, 0xE6, 0x80, 0x01, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF);
+ mipi_dsi_dcs_write_seq(dsi, 0xF0, 0x12, 0x03, 0x20, 0x00, 0xFF);
+ mipi_dsi_dcs_write_seq(dsi, 0xF3, 0x00);
+
+ ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
+ if (ret < 0) {
+ dev_err(dev, "Failed to exit sleep mode: %d\n", ret);
+ return ret;
+ }
+
+ msleep(120);
+
+ ret = mipi_dsi_dcs_set_display_on(dsi);
+ if (ret < 0) {
+ dev_err(dev, "Failed to set panel on: %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int boe_th101mb31ig002_disable(struct drm_panel *panel)
+{
+ struct boe_th101mb31ig002 *ctx = container_of(panel,
+ struct boe_th101mb31ig002,
+ panel);
+ struct mipi_dsi_device *dsi = ctx->dsi;
+ struct device *dev = &dsi->dev;
+ int ret;
+
+ ret = mipi_dsi_dcs_set_display_off(dsi);
+ if (ret < 0)
+ dev_err(dev, "Failed to set panel off: %d\n", ret);
+
+ msleep(120);
+
+ ret = mipi_dsi_dcs_enter_sleep_mode(dsi);
+ if (ret < 0)
+ dev_err(dev, "Failed to enter sleep mode: %d\n", ret);
+
+ return 0;
+}
+
+static int boe_th101mb31ig002_unprepare(struct drm_panel *panel)
+{
+ struct boe_th101mb31ig002 *ctx = container_of(panel,
+ struct boe_th101mb31ig002,
+ panel);
+
+ gpiod_set_value_cansleep(ctx->reset, 1);
+ gpiod_set_value_cansleep(ctx->enable, 0);
+ regulator_disable(ctx->power);
+
+ return 0;
+}
+
+static int boe_th101mb31ig002_prepare(struct drm_panel *panel)
+{
+ struct boe_th101mb31ig002 *ctx = container_of(panel,
+ struct boe_th101mb31ig002,
+ panel);
+ struct device *dev = &ctx->dsi->dev;
+ int ret;
+
+ ret = regulator_enable(ctx->power);
+ if (ret) {
+ dev_err(dev, "Failed to enable power supply: %d\n", ret);
+ return ret;
+ }
+
+ gpiod_set_value_cansleep(ctx->enable, 1);
+ msleep(50);
+ boe_th101mb31ig002_reset(ctx);
+ boe_th101mb31ig002_enable(panel);
+
+ return 0;
+}
+
+static const struct drm_display_mode boe_th101mb31ig002_default_mode = {
+ .clock = 73500,
+ .hdisplay = 800,
+ .hsync_start = 800 + 64,
+ .hsync_end = 800 + 64 + 16,
+ .htotal = 800 + 64 + 16 + 64,
+ .vdisplay = 1280,
+ .vsync_start = 1280 + 2,
+ .vsync_end = 1280 + 2 + 4,
+ .vtotal = 1280 + 2 + 4 + 12,
+ .width_mm = 135,
+ .height_mm = 216,
+ .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,
+};
+
+static int boe_th101mb31ig002_get_modes(struct drm_panel *panel,
+ struct drm_connector *connector)
+{
+ struct boe_th101mb31ig002 *ctx = container_of(panel,
+ struct boe_th101mb31ig002,
+ panel);
+ struct drm_display_mode *mode;
+
+ mode = drm_mode_duplicate(connector->dev,
+ &boe_th101mb31ig002_default_mode);
+ if (!mode) {
+ dev_err(panel->dev, "Failed to add mode %ux%u@%u\n",
+ boe_th101mb31ig002_default_mode.hdisplay,
+ boe_th101mb31ig002_default_mode.vdisplay,
+ drm_mode_vrefresh(&boe_th101mb31ig002_default_mode));
+ return -ENOMEM;
+ }
+
+ drm_mode_set_name(mode);
+
+ connector->display_info.bpc = 8;
+ connector->display_info.width_mm = mode->width_mm;
+ connector->display_info.height_mm = mode->height_mm;
+
+ /*
+ * TODO: Remove once all drm drivers call
+ * drm_connector_set_orientation_from_panel()
+ */
+ drm_connector_set_panel_orientation(connector, ctx->orientation);
+
+ drm_mode_probed_add(connector, mode);
+
+ return 1;
+}
+
+static enum drm_panel_orientation
+boe_th101mb31ig002_get_orientation(struct drm_panel *panel)
+{
+ struct boe_th101mb31ig002 *ctx = container_of(panel,
+ struct boe_th101mb31ig002,
+ panel);
+
+ return ctx->orientation;
+}
+
+static const struct drm_panel_funcs boe_th101mb31ig002_funcs = {
+ .prepare = boe_th101mb31ig002_prepare,
+ .unprepare = boe_th101mb31ig002_unprepare,
+ .disable = boe_th101mb31ig002_disable,
+ .get_modes = boe_th101mb31ig002_get_modes,
+ .get_orientation = boe_th101mb31ig002_get_orientation,
+};
+
+static int boe_th101mb31ig002_dsi_probe(struct mipi_dsi_device *dsi)
+{
+ struct boe_th101mb31ig002 *ctx;
+ int ret;
+
+ ctx = devm_kzalloc(&dsi->dev, sizeof(*ctx), GFP_KERNEL);
+ if (!ctx)
+ return -ENOMEM;
+
+ mipi_dsi_set_drvdata(dsi, ctx);
+ ctx->dsi = dsi;
+
+ dsi->lanes = 4;
+ dsi->format = MIPI_DSI_FMT_RGB888;
+ dsi->mode_flags = MIPI_DSI_MODE_VIDEO_BURST |
+ MIPI_DSI_MODE_NO_EOT_PACKET |
+ MIPI_DSI_MODE_LPM;
+
+ ctx->power = devm_regulator_get(&dsi->dev, "power");
+ if (IS_ERR(ctx->power))
+ return dev_err_probe(&dsi->dev, PTR_ERR(ctx->power),
+ "Failed to get power regulator\n");
+
+ ctx->enable = devm_gpiod_get(&dsi->dev, "enable", GPIOD_OUT_LOW);
+ if (IS_ERR(ctx->enable))
+ return dev_err_probe(&dsi->dev, PTR_ERR(ctx->enable),
+ "Failed to get enable GPIO\n");
+
+ ctx->reset = devm_gpiod_get(&dsi->dev, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(ctx->reset))
+ return dev_err_probe(&dsi->dev, PTR_ERR(ctx->reset),
+ "Failed to get reset GPIO\n");
+
+ ret = of_drm_get_panel_orientation(dsi->dev.of_node,
+ &ctx->orientation);
+ if (ret)
+ return dev_err_probe(&dsi->dev, ret,
+ "Failed to get orientation\n");
+
+ drm_panel_init(&ctx->panel, &dsi->dev, &boe_th101mb31ig002_funcs,
+ DRM_MODE_CONNECTOR_DSI);
+
+ ret = drm_panel_of_backlight(&ctx->panel);
+ if (ret)
+ return ret;
+
+ drm_panel_add(&ctx->panel);
+
+ ret = mipi_dsi_attach(dsi);
+ if (ret < 0) {
+ dev_err_probe(&dsi->dev, ret,
+ "Failed to attach panel to DSI host\n");
+ drm_panel_remove(&ctx->panel);
+ return ret;
+ }
+
+ return 0;
+}
+
+static void boe_th101mb31ig002_dsi_remove(struct mipi_dsi_device *dsi)
+{
+ struct boe_th101mb31ig002 *ctx = mipi_dsi_get_drvdata(dsi);
+
+ mipi_dsi_detach(dsi);
+ drm_panel_remove(&ctx->panel);
+}
+
+static const struct of_device_id boe_th101mb31ig002_of_match[] = {
+ { .compatible = "boe,th101mb31ig002-28a", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, boe_th101mb31ig002_of_match);
+
+static struct mipi_dsi_driver boe_th101mb31ig002_driver = {
+ .driver = {
+ .name = "boe-th101mb31ig002-28a",
+ .of_match_table = boe_th101mb31ig002_of_match,
+ },
+ .probe = boe_th101mb31ig002_dsi_probe,
+ .remove = boe_th101mb31ig002_dsi_remove,
+};
+module_mipi_dsi_driver(boe_th101mb31ig002_driver);
+
+MODULE_AUTHOR("Alexander Warnecke <[email protected]>");
+MODULE_DESCRIPTION("BOE TH101MB31IG002-28A MIPI-DSI LCD panel");
+MODULE_LICENSE("GPL");
--
2.43.0
This includes support for both the v0.1 units that were sent to developers and
the v2.0 units from production.
v1.0 is not included as no units are known to exist.
Working/Tested:
- SDMMC
- UART
- Buttons
- Charging/Battery/PMIC
- Audio
- USB
- Display
- SPI NOR Flash
Signed-off-by: Alexander Warnecke <[email protected]>
Signed-off-by: Manuel Traut <[email protected]>
---
arch/arm64/boot/dts/rockchip/Makefile | 2 +
.../boot/dts/rockchip/rk3566-pinetab2-v0.1.dts | 28 +
.../boot/dts/rockchip/rk3566-pinetab2-v2.0.dts | 48 ++
arch/arm64/boot/dts/rockchip/rk3566-pinetab2.dtsi | 943 +++++++++++++++++++++
4 files changed, 1021 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index a7b30e11beaf..ac0c72667bb7 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -78,6 +78,8 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg353vs.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg503.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.1.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.2.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinetab2-v0.1.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinetab2-v2.0.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-powkiddy-rgb30.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-powkiddy-rk2023.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-powkiddy-x55.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-pinetab2-v0.1.dts b/arch/arm64/boot/dts/rockchip/rk3566-pinetab2-v0.1.dts
new file mode 100644
index 000000000000..5fe6ca5da9d3
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-pinetab2-v0.1.dts
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-pinetab2.dtsi"
+
+/ {
+ model = "Pine64 PineTab2 v0.1";
+ compatible = "pine64,pinetab2-v0.1", "pine64,pinetab2", "rockchip,rk3566";
+};
+
+&lcd {
+ reset-gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_pwren_h &lcd0_rst_l>;
+};
+
+&pinctrl {
+ lcd0 {
+ lcd0_rst_l: lcd0-rst-l {
+ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&sdmmc1 {
+ vmmc-supply = <&vcc3v3_sys>;
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-pinetab2-v2.0.dts b/arch/arm64/boot/dts/rockchip/rk3566-pinetab2-v2.0.dts
new file mode 100644
index 000000000000..9349541cbbd0
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-pinetab2-v2.0.dts
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-pinetab2.dtsi"
+
+/ {
+ model = "Pine64 PineTab2 v2.0";
+ compatible = "pine64,pinetab2-v2.0", "pine64,pinetab2", "rockchip,rk3566";
+};
+
+&gpio_keys {
+ pinctrl-0 = <&kb_id_det>, <&hall_int_l>;
+
+ event-hall-sensor {
+ debounce-interval = <20>;
+ gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
+ label = "Hall Sensor";
+ linux,code = <SW_LID>;
+ linux,input-type = <EV_SW>;
+ wakeup-event-action = <EV_ACT_DEASSERTED>;
+ wakeup-source;
+ };
+};
+
+&lcd {
+ reset-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_pwren_h &lcd0_rst_l>;
+};
+
+&pinctrl {
+ lcd0 {
+ lcd0_rst_l: lcd0-rst-l {
+ rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ hall {
+ hall_int_l: hall-int-l {
+ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&sdmmc1 {
+ vmmc-supply = <&vcc_sys>;
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-pinetab2.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-pinetab2.dtsi
new file mode 100644
index 000000000000..db40281eafbe
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-pinetab2.dtsi
@@ -0,0 +1,943 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include <dt-bindings/usb/pd.h>
+#include "rk3566.dtsi"
+
+/ {
+ chassis-type = "tablet";
+
+ aliases {
+ mmc0 = &sdhci;
+ mmc1 = &sdmmc0;
+ };
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ adc-keys {
+ compatible = "adc-keys";
+ io-channels = <&saradc 0>;
+ io-channel-names = "buttons";
+ keyup-threshold-microvolt = <1800000>;
+ poll-interval = <25>;
+
+ button-vol-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ press-threshold-microvolt = <297500>;
+ };
+
+ button-vol-down {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ press-threshold-microvolt = <1750>;
+ };
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm4 0 25000 0>;
+ brightness-levels = <20 220>;
+ num-interpolated-steps = <200>;
+ default-brightness-level = <100>;
+ power-supply = <&vcc_sys>;
+ };
+
+ battery: battery {
+ compatible = "simple-battery";
+ charge-full-design-microamp-hours = <6000000>;
+ charge-term-current-microamp = <300000>;
+ constant-charge-current-max-microamp = <2000000>;
+ constant-charge-voltage-max-microvolt = <4300000>;
+ voltage-max-design-microvolt = <4350000>;
+ voltage-min-design-microvolt = <3400000>;
+
+ ocv-capacity-celsius = <20>;
+ ocv-capacity-table-0 = <4322000 100>, <4250000 95>, <4192000 90>, <4136000 85>,
+ <4080000 80>, <4022000 75>, <3972000 70>, <3928000 65>,
+ <3885000 60>, <3833000 55>, <3798000 50>, <3780000 45>,
+ <3776000 40>, <3773000 35>, <3755000 30>, <3706000 25>,
+ <3640000 20>, <3589000 15>, <3535000 10>, <3492000 5>,
+ <3400000 0>;
+ };
+
+ gpio_keys: gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&kb_id_det>;
+
+ tablet-mode-switch {
+ debounce-interval = <20>;
+ gpios = <&gpio4 RK_PA4 GPIO_ACTIVE_HIGH>;
+ label = "Tablet Mode";
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_TABLET_MODE>;
+ };
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "d";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ led-0 {
+ compatible = "regulator-led";
+ vled-supply = <&vcc5v0_flashled>;
+ color = <LED_COLOR_ID_WHITE>;
+ function = LED_FUNCTION_FLASH;
+ };
+
+ rk817-sound {
+ compatible = "simple-audio-card";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hp_det_l>;
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "rk817_ext";
+ simple-audio-card,mclk-fs = <256>;
+
+ simple-audio-card,widgets =
+ "Microphone", "Mic Jack",
+ "Headphone", "Headphones",
+ "Speaker", "Internal Speakers";
+
+ simple-audio-card,routing =
+ "MICR", "Mic Jack",
+ "Headphones", "HPOL",
+ "Headphones", "HPOR",
+ "Internal Speakers", "Speaker Amplifier OUTL",
+ "Internal Speakers", "Speaker Amplifier OUTR",
+ "Speaker Amplifier INL", "HPOL",
+ "Speaker Amplifier INR", "HPOR";
+ simple-audio-card,hp-det-gpio = <&gpio4 RK_PC6 GPIO_ACTIVE_LOW>;
+ simple-audio-card,aux-devs = <&speaker_amp>;
+ simple-audio-card,pin-switches = "Internal Speakers";
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1_8ch>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&rk817>;
+ };
+ };
+
+ speaker_amp: speaker-amplifier {
+ compatible = "simple-audio-amplifier";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spk_ctl>;
+ enable-gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
+ sound-name-prefix = "Speaker Amplifier";
+ VCC-supply = <&vcc_bat>;
+ };
+
+ vcc_3v3: vcc-3v3-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ vcc3v3_minipcie: vcc3v3-minipcie-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 RK_PC3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_pwren_h>;
+ regulator-name = "vcc3v3_minipcie";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc3v3_sd: vcc3v3-sd-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_pwren_l>;
+ regulator-name = "vcc3v3_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ vcc5v0_flashled: vcc5v0-flashled-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&flash_led_en_h>;
+ regulator-name = "vcc5v0_flashled";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v_midu>;
+ };
+
+ vcc5v0_usb_host0: vcc5v0-usb-host0-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 RK_PC4 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_host_pwren1_h>;
+ regulator-name = "vcc5v0_usb_host0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v_midu>;
+ };
+
+ vcc5v0_usb_host2: vcc5v0-usb-host2-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 RK_PC5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_host_pwren2_h>;
+ regulator-name = "vcc5v0_usb_host2";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v_midu>;
+ };
+
+ vcc_bat: vcc-bat-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_bat";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc_sys: vcc-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_bat>;
+ };
+
+ vdd1v2_dvp: vdd1v2-dvp-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd1v2_dvp";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ vin-supply = <&vcc_3v3>;
+ };
+};
+
+&combphy1 {
+ status = "okay";
+};
+
+&combphy2 {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cru {
+ assigned-clocks = <&pmucru CLK_RTC_32K>, <&cru PLL_GPLL>,
+ <&pmucru PLL_PPLL>, <&cru PLL_VPLL>;
+ assigned-clock-rates = <32768>, <1200000000>, <200000000>, <500000000>;
+ assigned-clock-parents = <&pmucru CLK_RTC32K_FRAC>;
+};
+
+&csi_dphy {
+ status = "okay";
+};
+
+&dsi0 {
+ status = "okay";
+ clock-master;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ lcd: panel@0 {
+ compatible = "boe,th101mb31ig002-28a";
+ reg = <0>;
+ backlight = <&backlight>;
+ enable-gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
+ rotation = <90>;
+ power-supply = <&vcc_3v3>;
+
+ port@0 {
+ panel_in_dsi: endpoint@0 {
+ remote-endpoint = <&dsi0_out_con>;
+ };
+ };
+ };
+};
+
+&dsi0_in {
+ dsi0_in_vp1: endpoint {
+ remote-endpoint = <&vp1_out_dsi0>;
+ };
+};
+
+&dsi0_out {
+ dsi0_out_con: endpoint {
+ remote-endpoint = <&panel_in_dsi>;
+ };
+};
+
+&dsi_dphy0 {
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu_npu>;
+ status = "okay";
+};
+
+&hdmi {
+ avdd-0v9-supply = <&vdda_0v9_p>;
+ avdd-1v8-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&hdmi_in {
+ hdmi_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi>;
+ };
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&hdmi_sound {
+ status = "okay";
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ vdd_cpu: regulator@1c {
+ compatible = "tcs,tcs4525";
+ reg = <0x1c>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-ramp-delay = <2300>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk817: pmic@20 {
+ compatible = "rockchip,rk817";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+ assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+ clock-names = "mclk";
+ clocks = <&cru I2S1_MCLKOUT_TX>;
+ clock-output-names = "rk808-clkout1", "rk808-clkout2";
+ #clock-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>;
+ rockchip,system-power-controller;
+ #sound-dai-cells = <0>;
+ wakeup-source;
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc5-supply = <&vcc_sys>;
+ vcc6-supply = <&vcc_sys>;
+ vcc7-supply = <&vcc_sys>;
+ vcc8-supply = <&vcc_sys>;
+ vcc9-supply = <&vcc5v_midu>;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vdd_logic";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu_npu: DCDC_REG2 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vdd_gpu_npu";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc_ddr";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc3v3_sys: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc3v3_sys";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdda_0v9_p: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdda_0v9_p";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdda0v9_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_acodec";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_1v8: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_1v8";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc1v8_dvp: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8_dvp";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc2v8_dvp: LDO_REG9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "vcc2v8_dvp";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc5v_midu: BOOST {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "boost";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vbus: OTG_SWITCH {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "otg_switch";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+
+ charger {
+ monitored-battery = <&battery>;
+ rockchip,resistor-sense-micro-ohms = <10000>;
+ rockchip,sleep-enter-current-microamp = <300000>;
+ rockchip,sleep-filter-current-microamp = <100000>;
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ touchscreen@5d {
+ compatible = "goodix,gt911";
+ reg = <0x5d>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PB0 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&tp_int_l_pmuio2>, <&tp_rst_l_pmuio2>;
+ AVDD28-supply = <&vcc3v3_pmu>;
+ VDDIO-supply = <&vcca1v8_pmu>;
+ irq-gpios = <&gpio0 RK_PB0 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <400000>;
+ pinctrl-0 = <&i2c2m1_xfer>;
+ status = "okay";
+
+ vcm@c {
+ compatible = "dongwoon,dw9714";
+ reg = <0x0c>;
+ vcc-supply = <&vcc1v8_dvp>;
+ };
+
+ camera@36 {
+ compatible = "ovti,ov5648";
+ reg = <0x36>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&camerab_pdn_l &camerab_rst_l>;
+
+ clocks = <&cru CLK_CIF_OUT>;
+ assigned-clocks = <&cru CLK_CIF_OUT>;
+ assigned-clock-rates = <24000000>;
+
+ avdd-supply = <&vcc2v8_dvp>;
+ dvdd-supply = <&vdd1v2_dvp>;
+ dovdd-supply = <&vcc1v8_dvp>;
+ powerdown-gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&gpio4 RK_PB1 GPIO_ACTIVE_LOW>;
+
+ port {
+ endpoint {
+ data-lanes = <1 2>;
+ remote-endpoint = <0>;
+ link-frequencies = /bits/ 64 <210000000 168000000>;
+ };
+ };
+ };
+};
+
+&i2c5 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ accelerometer@18 {
+ compatible = "silan,sc7a20";
+ reg = <0x18>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gsensor_int_l>;
+ st,drdy-int-pin = <1>;
+ vdd-supply = <&vcc_1v8>;
+ vddio-supply = <&vcc_1v8>;
+ mount-matrix = "1", "0", "0",
+ "0", "0", "1",
+ "0", "1", "0";
+ };
+};
+
+&i2s0_8ch {
+ status = "okay";
+};
+
+&i2s1_8ch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1m0_sclktx
+ &i2s1m0_lrcktx
+ &i2s1m0_sdi0
+ &i2s1m0_sdo0>;
+ rockchip,trcm-sync-tx-only;
+ status = "okay";
+};
+
+&pcie2x1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_reset_h>;
+ reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_minipcie>;
+ status = "okay";
+};
+
+&pinctrl {
+ camerab {
+ camerab_pdn_l: camerab-pdn-l {
+ rockchip,pins = <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ camerab_rst_l: camerab-rst-l {
+ rockchip,pins = <4 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ cameraf {
+ cameraf_pdn_l: cameraf-pdn-l {
+ rockchip,pins = <4 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ cameraf_rst_l: cameraf-rst-l {
+ rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ flash {
+ flash_led_en_h: flash-led-en-h {
+ rockchip,pins = <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ fspi {
+ fspi_dual_io_pins: fspi-dual-io-pins {
+ rockchip,pins =
+ /* fspi_clk */
+ <1 RK_PD0 1 &pcfg_pull_none>,
+ /* fspi_cs0n */
+ <1 RK_PD3 1 &pcfg_pull_none>,
+ /* fspi_d0 */
+ <1 RK_PD1 1 &pcfg_pull_none>,
+ /* fspi_d1 */
+ <1 RK_PD2 1 &pcfg_pull_none>;
+ };
+ };
+
+ gsensor {
+ gsensor_int_l: gsensor-int-l {
+ rockchip,pins = <3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ kb {
+ kb_id_det: kb-id-det {
+ rockchip,pins = <4 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ lcd {
+ lcd_pwren_h: lcd-pwren-h {
+ rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie {
+ pcie_pwren_h: pcie-pwren-h {
+ rockchip,pins = <4 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ pcie_reset_h: pcie-reset-h {
+ rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ sdmmc {
+ sdmmc_pwren_l: sdmmc-pwren-l {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sound {
+ hp_det_l: hp-det-l {
+ rockchip,pins = <4 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ spk_ctl: spk-ctl {
+ rockchip,pins = <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ tp {
+ tp_int_l_pmuio2: tp-int-l-pmuio2 {
+ rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ tp_rst_l_pmuio2: tp-rst-l-pmuio2 {
+ rockchip,pins = <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb {
+ usbcc_int_l: usbcc-int-l {
+ rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ usb_host_pwren1_h: usb-host-pwren1-h {
+ rockchip,pins = <4 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ usb_host_pwren2_h: usb-host-pwren2-h {
+ rockchip,pins = <4 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ wifi {
+ host_wake_wl: host-wake-wl {
+ rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ wifi_wake_host_h: wifi-wake-host-h {
+ rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmuio1-supply = <&vcc3v3_pmu>;
+ pmuio2-supply = <&vcca1v8_pmu>;
+ vccio1-supply = <&vccio_acodec>;
+ vccio2-supply = <&vcc_1v8>;
+ vccio3-supply = <&vccio_sd>;
+ vccio4-supply = <&vcc_1v8>;
+ vccio5-supply = <&vcc_1v8>;
+ vccio6-supply = <&vcc1v8_dvp>;
+ vccio7-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&pwm4 {
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ no-sdio;
+ no-sd;
+ non-removable;
+ max-frequency = <200000000>;
+ mmc-hs200-1_8v;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8
+ &emmc_clk
+ &emmc_cmd
+ &emmc_datastrobe
+ &emmc_rstnout>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_bus4
+ &sdmmc0_clk
+ &sdmmc0_cmd
+ &sdmmc0_det>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc3v3_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&sdmmc1 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc1_bus4
+ &sdmmc1_cmd
+ &sdmmc1_clk>;
+ sd-uhs-sdr104;
+ vqmmc-supply = <&vcca1v8_pmu>;
+ status = "okay";
+};
+
+&sfc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&fspi_dual_io_pins>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <100000000>;
+ spi-rx-bus-width = <2>;
+ spi-tx-bus-width = <1>;
+ };
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <1>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ status = "okay";
+};
+
+&usb_host1_xhci {
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy0_host {
+ phy-supply = <&vcc5v0_usb_host0>;
+ status = "okay";
+};
+
+&usb2phy0_otg {
+ status = "okay";
+};
+
+&usb2phy1 {
+ status = "okay";
+};
+
+&usb2phy1_otg {
+ phy-supply = <&vcc5v0_usb_host2>;
+ status = "okay";
+};
+
+&vop {
+ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi_in_vp0>;
+ };
+};
+
+&vp1 {
+ vp1_out_dsi0: endpoint@ROCKCHIP_VOP2_EP_MIPI0 {
+ reg = <ROCKCHIP_VOP2_EP_MIPI0>;
+ remote-endpoint = <&dsi0_in_vp1>;
+ };
+};
--
2.43.0
Hi Manuel,
Since the BOE patches have been accepted to next, you do not need to include
it in this patch series.
Best regards,
Dang
On Saturday, January 27, 2024 4:48:41 PM +07 Manuel Traut wrote:
> - BOE TH101MB31IG002 LCD Panel:
> * Picked patches from https://anongit.freedesktop.org/git/drm/drm-misc.git
> (drm-misc-next)
Hello Manuel,
thank you for the changes, and finding time to post this.
On Sat, Jan 27, 2024 at 10:48:45AM +0100, Manuel Traut wrote:
> This includes support for both the v0.1 units that were sent to developers and
> the v2.0 units from production.
>
> v1.0 is not included as no units are known to exist.
>
> Working/Tested:
> - SDMMC
> - UART
> - Buttons
> - Charging/Battery/PMIC
> - Audio
> - USB
> - Display
> - SPI NOR Flash
>
> Signed-off-by: Alexander Warnecke <[email protected]>
> Signed-off-by: Manuel Traut <[email protected]>
Reviewed-by: Ondrej Jirman <[email protected]>
Tested-by: Ondrej Jirman <[email protected]>
kind regards,
o.
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 2 +
> .../boot/dts/rockchip/rk3566-pinetab2-v0.1.dts | 28 +
> .../boot/dts/rockchip/rk3566-pinetab2-v2.0.dts | 48 ++
> arch/arm64/boot/dts/rockchip/rk3566-pinetab2.dtsi | 943 +++++++++++++++++++++
> 4 files changed, 1021 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index a7b30e11beaf..ac0c72667bb7 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -78,6 +78,8 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg353vs.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg503.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.1.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.2.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinetab2-v0.1.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinetab2-v2.0.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-powkiddy-rgb30.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-powkiddy-rk2023.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-powkiddy-x55.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3566-pinetab2-v0.1.dts b/arch/arm64/boot/dts/rockchip/rk3566-pinetab2-v0.1.dts
> new file mode 100644
> index 000000000000..5fe6ca5da9d3
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3566-pinetab2-v0.1.dts
> @@ -0,0 +1,28 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include "rk3566-pinetab2.dtsi"
> +
> +/ {
> + model = "Pine64 PineTab2 v0.1";
> + compatible = "pine64,pinetab2-v0.1", "pine64,pinetab2", "rockchip,rk3566";
> +};
> +
> +&lcd {
> + reset-gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&lcd_pwren_h &lcd0_rst_l>;
> +};
> +
> +&pinctrl {
> + lcd0 {
> + lcd0_rst_l: lcd0-rst-l {
> + rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&sdmmc1 {
> + vmmc-supply = <&vcc3v3_sys>;
> +};
> diff --git a/arch/arm64/boot/dts/rockchip/rk3566-pinetab2-v2.0.dts b/arch/arm64/boot/dts/rockchip/rk3566-pinetab2-v2.0.dts
> new file mode 100644
> index 000000000000..9349541cbbd0
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3566-pinetab2-v2.0.dts
> @@ -0,0 +1,48 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include "rk3566-pinetab2.dtsi"
> +
> +/ {
> + model = "Pine64 PineTab2 v2.0";
> + compatible = "pine64,pinetab2-v2.0", "pine64,pinetab2", "rockchip,rk3566";
> +};
> +
> +&gpio_keys {
> + pinctrl-0 = <&kb_id_det>, <&hall_int_l>;
> +
> + event-hall-sensor {
> + debounce-interval = <20>;
> + gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
> + label = "Hall Sensor";
> + linux,code = <SW_LID>;
> + linux,input-type = <EV_SW>;
> + wakeup-event-action = <EV_ACT_DEASSERTED>;
> + wakeup-source;
> + };
> +};
> +
> +&lcd {
> + reset-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&lcd_pwren_h &lcd0_rst_l>;
> +};
> +
> +&pinctrl {
> + lcd0 {
> + lcd0_rst_l: lcd0-rst-l {
> + rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + hall {
> + hall_int_l: hall-int-l {
> + rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&sdmmc1 {
> + vmmc-supply = <&vcc_sys>;
> +};
> diff --git a/arch/arm64/boot/dts/rockchip/rk3566-pinetab2.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-pinetab2.dtsi
> new file mode 100644
> index 000000000000..db40281eafbe
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3566-pinetab2.dtsi
> @@ -0,0 +1,943 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/gpio-keys.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/soc/rockchip,vop2.h>
> +#include <dt-bindings/usb/pd.h>
> +#include "rk3566.dtsi"
> +
> +/ {
> + chassis-type = "tablet";
> +
> + aliases {
> + mmc0 = &sdhci;
> + mmc1 = &sdmmc0;
> + };
> +
> + chosen {
> + stdout-path = "serial2:1500000n8";
> + };
> +
> + adc-keys {
> + compatible = "adc-keys";
> + io-channels = <&saradc 0>;
> + io-channel-names = "buttons";
> + keyup-threshold-microvolt = <1800000>;
> + poll-interval = <25>;
> +
> + button-vol-up {
> + label = "Volume Up";
> + linux,code = <KEY_VOLUMEUP>;
> + press-threshold-microvolt = <297500>;
> + };
> +
> + button-vol-down {
> + label = "Volume Down";
> + linux,code = <KEY_VOLUMEDOWN>;
> + press-threshold-microvolt = <1750>;
> + };
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm4 0 25000 0>;
> + brightness-levels = <20 220>;
> + num-interpolated-steps = <200>;
> + default-brightness-level = <100>;
> + power-supply = <&vcc_sys>;
> + };
> +
> + battery: battery {
> + compatible = "simple-battery";
> + charge-full-design-microamp-hours = <6000000>;
> + charge-term-current-microamp = <300000>;
> + constant-charge-current-max-microamp = <2000000>;
> + constant-charge-voltage-max-microvolt = <4300000>;
> + voltage-max-design-microvolt = <4350000>;
> + voltage-min-design-microvolt = <3400000>;
> +
> + ocv-capacity-celsius = <20>;
> + ocv-capacity-table-0 = <4322000 100>, <4250000 95>, <4192000 90>, <4136000 85>,
> + <4080000 80>, <4022000 75>, <3972000 70>, <3928000 65>,
> + <3885000 60>, <3833000 55>, <3798000 50>, <3780000 45>,
> + <3776000 40>, <3773000 35>, <3755000 30>, <3706000 25>,
> + <3640000 20>, <3589000 15>, <3535000 10>, <3492000 5>,
> + <3400000 0>;
> + };
> +
> + gpio_keys: gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&kb_id_det>;
> +
> + tablet-mode-switch {
> + debounce-interval = <20>;
> + gpios = <&gpio4 RK_PA4 GPIO_ACTIVE_HIGH>;
> + label = "Tablet Mode";
> + linux,input-type = <EV_SW>;
> + linux,code = <SW_TABLET_MODE>;
> + };
> + };
> +
> + hdmi-connector {
> + compatible = "hdmi-connector";
> + type = "d";
> +
> + port {
> + hdmi_con_in: endpoint {
> + remote-endpoint = <&hdmi_out_con>;
> + };
> + };
> + };
> +
> + led-0 {
> + compatible = "regulator-led";
> + vled-supply = <&vcc5v0_flashled>;
> + color = <LED_COLOR_ID_WHITE>;
> + function = LED_FUNCTION_FLASH;
> + };
> +
> + rk817-sound {
> + compatible = "simple-audio-card";
> + pinctrl-names = "default";
> + pinctrl-0 = <&hp_det_l>;
> + simple-audio-card,format = "i2s";
> + simple-audio-card,name = "rk817_ext";
> + simple-audio-card,mclk-fs = <256>;
> +
> + simple-audio-card,widgets =
> + "Microphone", "Mic Jack",
> + "Headphone", "Headphones",
> + "Speaker", "Internal Speakers";
> +
> + simple-audio-card,routing =
> + "MICR", "Mic Jack",
> + "Headphones", "HPOL",
> + "Headphones", "HPOR",
> + "Internal Speakers", "Speaker Amplifier OUTL",
> + "Internal Speakers", "Speaker Amplifier OUTR",
> + "Speaker Amplifier INL", "HPOL",
> + "Speaker Amplifier INR", "HPOR";
> + simple-audio-card,hp-det-gpio = <&gpio4 RK_PC6 GPIO_ACTIVE_LOW>;
> + simple-audio-card,aux-devs = <&speaker_amp>;
> + simple-audio-card,pin-switches = "Internal Speakers";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&i2s1_8ch>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&rk817>;
> + };
> + };
> +
> + speaker_amp: speaker-amplifier {
> + compatible = "simple-audio-amplifier";
> + pinctrl-names = "default";
> + pinctrl-0 = <&spk_ctl>;
> + enable-gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
> + sound-name-prefix = "Speaker Amplifier";
> + VCC-supply = <&vcc_bat>;
> + };
> +
> + vcc_3v3: vcc-3v3-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_3v3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc3v3_sys>;
> + };
> +
> + vcc3v3_minipcie: vcc3v3-minipcie-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio4 RK_PC3 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie_pwren_h>;
> + regulator-name = "vcc3v3_minipcie";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + vcc3v3_sd: vcc3v3-sd-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_pwren_l>;
> + regulator-name = "vcc3v3_sd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc3v3_sys>;
> + };
> +
> + vcc5v0_flashled: vcc5v0-flashled-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&flash_led_en_h>;
> + regulator-name = "vcc5v0_flashled";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc5v_midu>;
> + };
> +
> + vcc5v0_usb_host0: vcc5v0-usb-host0-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio4 RK_PC4 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb_host_pwren1_h>;
> + regulator-name = "vcc5v0_usb_host0";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc5v_midu>;
> + };
> +
> + vcc5v0_usb_host2: vcc5v0-usb-host2-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio4 RK_PC5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb_host_pwren2_h>;
> + regulator-name = "vcc5v0_usb_host2";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc5v_midu>;
> + };
> +
> + vcc_bat: vcc-bat-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_bat";
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vcc_sys: vcc-sys-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_bat>;
> + };
> +
> + vdd1v2_dvp: vdd1v2-dvp-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd1v2_dvp";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + vin-supply = <&vcc_3v3>;
> + };
> +};
> +
> +&combphy1 {
> + status = "okay";
> +};
> +
> +&combphy2 {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu2 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu3 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cru {
> + assigned-clocks = <&pmucru CLK_RTC_32K>, <&cru PLL_GPLL>,
> + <&pmucru PLL_PPLL>, <&cru PLL_VPLL>;
> + assigned-clock-rates = <32768>, <1200000000>, <200000000>, <500000000>;
> + assigned-clock-parents = <&pmucru CLK_RTC32K_FRAC>;
> +};
> +
> +&csi_dphy {
> + status = "okay";
> +};
> +
> +&dsi0 {
> + status = "okay";
> + clock-master;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + lcd: panel@0 {
> + compatible = "boe,th101mb31ig002-28a";
> + reg = <0>;
> + backlight = <&backlight>;
> + enable-gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
> + rotation = <90>;
> + power-supply = <&vcc_3v3>;
> +
> + port@0 {
> + panel_in_dsi: endpoint@0 {
> + remote-endpoint = <&dsi0_out_con>;
> + };
> + };
> + };
> +};
> +
> +&dsi0_in {
> + dsi0_in_vp1: endpoint {
> + remote-endpoint = <&vp1_out_dsi0>;
> + };
> +};
> +
> +&dsi0_out {
> + dsi0_out_con: endpoint {
> + remote-endpoint = <&panel_in_dsi>;
> + };
> +};
> +
> +&dsi_dphy0 {
> + status = "okay";
> +};
> +
> +&gpu {
> + mali-supply = <&vdd_gpu_npu>;
> + status = "okay";
> +};
> +
> +&hdmi {
> + avdd-0v9-supply = <&vdda_0v9_p>;
> + avdd-1v8-supply = <&vcc_1v8>;
> + status = "okay";
> +};
> +
> +&hdmi_in {
> + hdmi_in_vp0: endpoint {
> + remote-endpoint = <&vp0_out_hdmi>;
> + };
> +};
> +
> +&hdmi_out {
> + hdmi_out_con: endpoint {
> + remote-endpoint = <&hdmi_con_in>;
> + };
> +};
> +
> +&hdmi_sound {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + vdd_cpu: regulator@1c {
> + compatible = "tcs,tcs4525";
> + reg = <0x1c>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_cpu";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1150000>;
> + regulator-ramp-delay = <2300>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + rk817: pmic@20 {
> + compatible = "rockchip,rk817";
> + reg = <0x20>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
> + assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
> + assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
> + clock-names = "mclk";
> + clocks = <&cru I2S1_MCLKOUT_TX>;
> + clock-output-names = "rk808-clkout1", "rk808-clkout2";
> + #clock-cells = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>;
> + rockchip,system-power-controller;
> + #sound-dai-cells = <0>;
> + wakeup-source;
> +
> + vcc1-supply = <&vcc_sys>;
> + vcc2-supply = <&vcc_sys>;
> + vcc3-supply = <&vcc_sys>;
> + vcc4-supply = <&vcc_sys>;
> + vcc5-supply = <&vcc_sys>;
> + vcc6-supply = <&vcc_sys>;
> + vcc7-supply = <&vcc_sys>;
> + vcc8-supply = <&vcc_sys>;
> + vcc9-supply = <&vcc5v_midu>;
> +
> + regulators {
> + vdd_logic: DCDC_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> + regulator-initial-mode = <0x2>;
> + regulator-name = "vdd_logic";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu_npu: DCDC_REG2 {
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> + regulator-initial-mode = <0x2>;
> + regulator-name = "vdd_gpu_npu";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-initial-mode = <0x2>;
> + regulator-name = "vcc_ddr";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc3v3_sys: DCDC_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-initial-mode = <0x2>;
> + regulator-name = "vcc3v3_sys";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcca1v8_pmu: LDO_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcca1v8_pmu";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vdda_0v9_p: LDO_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-name = "vdda_0v9_p";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdda0v9_pmu: LDO_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-name = "vdda0v9_pmu";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vccio_acodec: LDO_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio_acodec";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vccio_sd: LDO_REG5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio_sd";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc3v3_pmu: LDO_REG6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc3v3_pmu";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_1v8: LDO_REG7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc_1v8";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc1v8_dvp: LDO_REG8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc1v8_dvp";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc2v8_dvp: LDO_REG9 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-name = "vcc2v8_dvp";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc5v_midu: BOOST {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "boost";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vbus: OTG_SWITCH {
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "otg_switch";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> + };
> +
> + charger {
> + monitored-battery = <&battery>;
> + rockchip,resistor-sense-micro-ohms = <10000>;
> + rockchip,sleep-enter-current-microamp = <300000>;
> + rockchip,sleep-filter-current-microamp = <100000>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + touchscreen@5d {
> + compatible = "goodix,gt911";
> + reg = <0x5d>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PB0 IRQ_TYPE_EDGE_FALLING>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&tp_int_l_pmuio2>, <&tp_rst_l_pmuio2>;
> + AVDD28-supply = <&vcc3v3_pmu>;
> + VDDIO-supply = <&vcca1v8_pmu>;
> + irq-gpios = <&gpio0 RK_PB0 GPIO_ACTIVE_HIGH>;
> + reset-gpios = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>;
> + };
> +};
> +
> +&i2c2 {
> + clock-frequency = <400000>;
> + pinctrl-0 = <&i2c2m1_xfer>;
> + status = "okay";
> +
> + vcm@c {
> + compatible = "dongwoon,dw9714";
> + reg = <0x0c>;
> + vcc-supply = <&vcc1v8_dvp>;
> + };
> +
> + camera@36 {
> + compatible = "ovti,ov5648";
> + reg = <0x36>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&camerab_pdn_l &camerab_rst_l>;
> +
> + clocks = <&cru CLK_CIF_OUT>;
> + assigned-clocks = <&cru CLK_CIF_OUT>;
> + assigned-clock-rates = <24000000>;
> +
> + avdd-supply = <&vcc2v8_dvp>;
> + dvdd-supply = <&vdd1v2_dvp>;
> + dovdd-supply = <&vcc1v8_dvp>;
> + powerdown-gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_LOW>;
> + reset-gpios = <&gpio4 RK_PB1 GPIO_ACTIVE_LOW>;
> +
> + port {
> + endpoint {
> + data-lanes = <1 2>;
> + remote-endpoint = <0>;
> + link-frequencies = /bits/ 64 <210000000 168000000>;
> + };
> + };
> + };
> +};
> +
> +&i2c5 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + accelerometer@18 {
> + compatible = "silan,sc7a20";
> + reg = <0x18>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&gsensor_int_l>;
> + st,drdy-int-pin = <1>;
> + vdd-supply = <&vcc_1v8>;
> + vddio-supply = <&vcc_1v8>;
> + mount-matrix = "1", "0", "0",
> + "0", "0", "1",
> + "0", "1", "0";
> + };
> +};
> +
> +&i2s0_8ch {
> + status = "okay";
> +};
> +
> +&i2s1_8ch {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2s1m0_sclktx
> + &i2s1m0_lrcktx
> + &i2s1m0_sdi0
> + &i2s1m0_sdo0>;
> + rockchip,trcm-sync-tx-only;
> + status = "okay";
> +};
> +
> +&pcie2x1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie_reset_h>;
> + reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
> + vpcie3v3-supply = <&vcc3v3_minipcie>;
> + status = "okay";
> +};
> +
> +&pinctrl {
> + camerab {
> + camerab_pdn_l: camerab-pdn-l {
> + rockchip,pins = <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + camerab_rst_l: camerab-rst-l {
> + rockchip,pins = <4 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + cameraf {
> + cameraf_pdn_l: cameraf-pdn-l {
> + rockchip,pins = <4 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + cameraf_rst_l: cameraf-rst-l {
> + rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + flash {
> + flash_led_en_h: flash-led-en-h {
> + rockchip,pins = <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + fspi {
> + fspi_dual_io_pins: fspi-dual-io-pins {
> + rockchip,pins =
> + /* fspi_clk */
> + <1 RK_PD0 1 &pcfg_pull_none>,
> + /* fspi_cs0n */
> + <1 RK_PD3 1 &pcfg_pull_none>,
> + /* fspi_d0 */
> + <1 RK_PD1 1 &pcfg_pull_none>,
> + /* fspi_d1 */
> + <1 RK_PD2 1 &pcfg_pull_none>;
> + };
> + };
> +
> + gsensor {
> + gsensor_int_l: gsensor-int-l {
> + rockchip,pins = <3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + kb {
> + kb_id_det: kb-id-det {
> + rockchip,pins = <4 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + lcd {
> + lcd_pwren_h: lcd-pwren-h {
> + rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + pcie {
> + pcie_pwren_h: pcie-pwren-h {
> + rockchip,pins = <4 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + pcie_reset_h: pcie-reset-h {
> + rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + pmic {
> + pmic_int_l: pmic-int-l {
> + rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + sdmmc {
> + sdmmc_pwren_l: sdmmc-pwren-l {
> + rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + sound {
> + hp_det_l: hp-det-l {
> + rockchip,pins = <4 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + spk_ctl: spk-ctl {
> + rockchip,pins = <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + tp {
> + tp_int_l_pmuio2: tp-int-l-pmuio2 {
> + rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + tp_rst_l_pmuio2: tp-rst-l-pmuio2 {
> + rockchip,pins = <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + usb {
> + usbcc_int_l: usbcc-int-l {
> + rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + usb_host_pwren1_h: usb-host-pwren1-h {
> + rockchip,pins = <4 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + usb_host_pwren2_h: usb-host-pwren2-h {
> + rockchip,pins = <4 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + wifi {
> + host_wake_wl: host-wake-wl {
> + rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + wifi_wake_host_h: wifi-wake-host-h {
> + rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +};
> +
> +&pmu_io_domains {
> + pmuio1-supply = <&vcc3v3_pmu>;
> + pmuio2-supply = <&vcca1v8_pmu>;
> + vccio1-supply = <&vccio_acodec>;
> + vccio2-supply = <&vcc_1v8>;
> + vccio3-supply = <&vccio_sd>;
> + vccio4-supply = <&vcc_1v8>;
> + vccio5-supply = <&vcc_1v8>;
> + vccio6-supply = <&vcc1v8_dvp>;
> + vccio7-supply = <&vcc_3v3>;
> + status = "okay";
> +};
> +
> +&pwm4 {
> + status = "okay";
> +};
> +
> +&saradc {
> + vref-supply = <&vcc_1v8>;
> + status = "okay";
> +};
> +
> +&sdhci {
> + bus-width = <8>;
> + no-sdio;
> + no-sd;
> + non-removable;
> + max-frequency = <200000000>;
> + mmc-hs200-1_8v;
> + pinctrl-names = "default";
> + pinctrl-0 = <&emmc_bus8
> + &emmc_clk
> + &emmc_cmd
> + &emmc_datastrobe
> + &emmc_rstnout>;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vcc_1v8>;
> + status = "okay";
> +};
> +
> +&sdmmc0 {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
> + disable-wp;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc0_bus4
> + &sdmmc0_clk
> + &sdmmc0_cmd
> + &sdmmc0_det>;
> + sd-uhs-sdr104;
> + vmmc-supply = <&vcc3v3_sd>;
> + vqmmc-supply = <&vccio_sd>;
> + status = "okay";
> +};
> +
> +&sdmmc1 {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cap-sdio-irq;
> + keep-power-in-suspend;
> + non-removable;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc1_bus4
> + &sdmmc1_cmd
> + &sdmmc1_clk>;
> + sd-uhs-sdr104;
> + vqmmc-supply = <&vcca1v8_pmu>;
> + status = "okay";
> +};
> +
> +&sfc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&fspi_dual_io_pins>;
> + status = "okay";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <100000000>;
> + spi-rx-bus-width = <2>;
> + spi-tx-bus-width = <1>;
> + };
> +};
> +
> +&tsadc {
> + rockchip,hw-tshut-mode = <1>;
> + rockchip,hw-tshut-polarity = <0>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_host0_ohci {
> + status = "okay";
> +};
> +
> +&usb_host0_xhci {
> + status = "okay";
> +};
> +
> +&usb_host1_xhci {
> + status = "okay";
> +};
> +
> +&usb2phy0 {
> + status = "okay";
> +};
> +
> +&usb2phy0_host {
> + phy-supply = <&vcc5v0_usb_host0>;
> + status = "okay";
> +};
> +
> +&usb2phy0_otg {
> + status = "okay";
> +};
> +
> +&usb2phy1 {
> + status = "okay";
> +};
> +
> +&usb2phy1_otg {
> + phy-supply = <&vcc5v0_usb_host2>;
> + status = "okay";
> +};
> +
> +&vop {
> + assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
> + assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
> + status = "okay";
> +};
> +
> +&vop_mmu {
> + status = "okay";
> +};
> +
> +&vp0 {
> + vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
> + reg = <ROCKCHIP_VOP2_EP_HDMI0>;
> + remote-endpoint = <&hdmi_in_vp0>;
> + };
> +};
> +
> +&vp1 {
> + vp1_out_dsi0: endpoint@ROCKCHIP_VOP2_EP_MIPI0 {
> + reg = <ROCKCHIP_VOP2_EP_MIPI0>;
> + remote-endpoint = <&dsi0_in_vp1>;
> + };
> +};
>
> --
> 2.43.0
>
Hi Dang,
On Sat, Jan 27, 2024 at 06:35:50PM +0700, Dang Huynh wrote:
> Hi Manuel,
>
> Since the BOE patches have been accepted to next, you do not need to include
> it in this patch series.
sorry, I thought patches to LKML shall be against Linux master since the
patches are still only in drm-next I considered to keep them in the queue.
Regards
Manuel
> On Saturday, January 27, 2024 4:48:41 PM +07 Manuel Traut wrote:
> > - BOE TH101MB31IG002 LCD Panel:
> > * Picked patches from https://anongit.freedesktop.org/git/drm/drm-misc.git
> > (drm-misc-next)
>
>
Am Dienstag, 30. Januar 2024, 20:36:22 CET schrieb Manuel Traut:
> Hi Dang,
>
> On Sat, Jan 27, 2024 at 06:35:50PM +0700, Dang Huynh wrote:
> > Hi Manuel,
> >
> > Since the BOE patches have been accepted to next, you do not need to include
> > it in this patch series.
>
> sorry, I thought patches to LKML shall be against Linux master since the
> patches are still only in drm-next I considered to keep them in the queue.
normally if parts of the v(x-1) version of your series are already
applied somewhere you just mention that fact in the cover-letter
in the changelog, like "dropped display patches already applied to drm-misc"
Just to make sure, there is no need for a resend, I'll look at and pick
just the remaining patches :-)
Heiko
On Saturday, 27 January 2024 10:48:45 CET Manuel Traut wrote:
> This includes support for both the v0.1 units that were sent to developers
> and the v2.0 units from production.
>
> v1.0 is not included as no units are known to exist.
>
> Working/Tested:
> - SDMMC
> - UART
> - Buttons
> - Charging/Battery/PMIC
> - Audio
> - USB
> - Display
> - SPI NOR Flash
>
> Signed-off-by: Alexander Warnecke <[email protected]>
> Signed-off-by: Manuel Traut <[email protected]>
Everything seems to (still) work, so:
Tested-By: Diederik de Haas <[email protected]>
Thanks for submitting this upstream :-)
Cheers,
Diederik
On Sat, 27 Jan 2024 10:48:41 +0100, Manuel Traut wrote:
> This adds support for the BOE TH101MB31IG002 LCD Panel used in PineTab2 [1] and
> PineTab-V [2] as well as the devictrees for the PineTab2 v0.1 and v2.0.
>
> The BOE LCD Panel patch was retrieved from [3]. The function-name prefix has
> been adapted and the LCD init section was simplified.
>
> The PineTab2 devicetree patch was retrieved from [4]. Some renaming was needed
> to pass the dtb-checks, the brightness-levels are specified as range and steps
> instead of a list of values.
>
> [...]
Applied, thanks!
[3/4] dt-bindings: arm64: rockchip: Add Pine64 PineTab2
commit: 6a0a5a2a71b3e3c4ae1ee0b34a496cbf2d980832
[4/4] arm64: dts: rockchip: Add devicetree for Pine64 PineTab2
commit: 1b7e19448f8fbeee23111795f67a003431c40b27
Best regards,
--
Heiko Stuebner <[email protected]>
Tested-by: Dang Huynh <[email protected]>
On Saturday, January 27, 2024 9:48:45 AM UTC Manuel Traut wrote:
> This includes support for both the v0.1 units that were sent to developers
> and the v2.0 units from production.