Using dev_err_probe() brings several improvements:
- emits the symbolic error code
- properly handles EPROBE_DEFER
- combines error message generation and return value handling
While at it add error messages to two error paths that were silent
before.
Signed-off-by: Uwe Kleine-König <[email protected]>
---
drivers/bus/ts-nbus.c | 66 ++++++++++++++++++-------------------------
1 file changed, 28 insertions(+), 38 deletions(-)
diff --git a/drivers/bus/ts-nbus.c b/drivers/bus/ts-nbus.c
index 19c5d1f4e4d7..baf22a82c47a 100644
--- a/drivers/bus/ts-nbus.c
+++ b/drivers/bus/ts-nbus.c
@@ -39,45 +39,39 @@ struct ts_nbus {
/*
* request all gpios required by the bus.
*/
-static int ts_nbus_init_pdata(struct platform_device *pdev, struct ts_nbus
- *ts_nbus)
+static int ts_nbus_init_pdata(struct platform_device *pdev,
+ struct ts_nbus *ts_nbus)
{
ts_nbus->data = devm_gpiod_get_array(&pdev->dev, "ts,data",
GPIOD_OUT_HIGH);
- if (IS_ERR(ts_nbus->data)) {
- dev_err(&pdev->dev, "failed to retrieve ts,data-gpio from dts\n");
- return PTR_ERR(ts_nbus->data);
- }
+ if (IS_ERR(ts_nbus->data))
+ return dev_err_probe(&pdev->dev, PTR_ERR(ts_nbus->data),
+ "failed to retrieve ts,data-gpio from dts\n");
ts_nbus->csn = devm_gpiod_get(&pdev->dev, "ts,csn", GPIOD_OUT_HIGH);
- if (IS_ERR(ts_nbus->csn)) {
- dev_err(&pdev->dev, "failed to retrieve ts,csn-gpio from dts\n");
- return PTR_ERR(ts_nbus->csn);
- }
+ if (IS_ERR(ts_nbus->csn))
+ return dev_err_probe(&pdev->dev, PTR_ERR(ts_nbus->csn),
+ "failed to retrieve ts,csn-gpio from dts\n");
ts_nbus->txrx = devm_gpiod_get(&pdev->dev, "ts,txrx", GPIOD_OUT_HIGH);
- if (IS_ERR(ts_nbus->txrx)) {
- dev_err(&pdev->dev, "failed to retrieve ts,txrx-gpio from dts\n");
- return PTR_ERR(ts_nbus->txrx);
- }
+ if (IS_ERR(ts_nbus->txrx))
+ return dev_err_probe(&pdev->dev, PTR_ERR(ts_nbus->txrx),
+ "failed to retrieve ts,txrx-gpio from dts\n");
ts_nbus->strobe = devm_gpiod_get(&pdev->dev, "ts,strobe", GPIOD_OUT_HIGH);
- if (IS_ERR(ts_nbus->strobe)) {
- dev_err(&pdev->dev, "failed to retrieve ts,strobe-gpio from dts\n");
- return PTR_ERR(ts_nbus->strobe);
- }
+ if (IS_ERR(ts_nbus->strobe))
+ return dev_err_probe(&pdev->dev, PTR_ERR(ts_nbus->strobe),
+ "failed to retrieve ts,strobe-gpio from dts\n");
ts_nbus->ale = devm_gpiod_get(&pdev->dev, "ts,ale", GPIOD_OUT_HIGH);
- if (IS_ERR(ts_nbus->ale)) {
- dev_err(&pdev->dev, "failed to retrieve ts,ale-gpio from dts\n");
- return PTR_ERR(ts_nbus->ale);
- }
+ if (IS_ERR(ts_nbus->ale))
+ return dev_err_probe(&pdev->dev, PTR_ERR(ts_nbus->ale),
+ "failed to retrieve ts,ale-gpio from dts\n");
ts_nbus->rdy = devm_gpiod_get(&pdev->dev, "ts,rdy", GPIOD_IN);
- if (IS_ERR(ts_nbus->rdy)) {
- dev_err(&pdev->dev, "failed to retrieve ts,rdy-gpio from dts\n");
- return PTR_ERR(ts_nbus->rdy);
- }
+ if (IS_ERR(ts_nbus->rdy))
+ return dev_err_probe(&pdev->dev, PTR_ERR(ts_nbus->rdy),
+ "failed to retrieve ts,rdy-gpio from dts\n");
return 0;
}
@@ -289,25 +283,20 @@ static int ts_nbus_probe(struct platform_device *pdev)
return ret;
pwm = devm_pwm_get(dev, NULL);
- if (IS_ERR(pwm)) {
- ret = PTR_ERR(pwm);
- if (ret != -EPROBE_DEFER)
- dev_err(dev, "unable to request PWM\n");
- return ret;
- }
+ if (IS_ERR(pwm))
+ return dev_err_probe(dev, PTR_ERR(pwm),
+ "unable to request PWM\n");
pwm_init_state(pwm, &state);
- if (!state.period) {
- dev_err(&pdev->dev, "invalid PWM period\n");
- return -EINVAL;
- }
+ if (!state.period)
+ return dev_err_probe(dev, -EINVAL, "invalid PWM period\n");
state.duty_cycle = state.period;
state.enabled = true;
ret = pwm_apply_state(pwm, &state);
if (ret < 0)
- return ret;
+ return dev_err_probe(dev, ret, "failed to configure PWM\n");
/*
* we can now start the FPGA and populate the peripherals.
@@ -321,7 +310,8 @@ static int ts_nbus_probe(struct platform_device *pdev)
ret = of_platform_populate(dev->of_node, NULL, NULL, dev);
if (ret < 0)
- return ret;
+ return dev_err_probe(dev, ret,
+ "failed to populate platform devices on bus\n");
dev_info(dev, "initialized\n");
--
2.43.0