This patch adds the required connection between netlink ethtool and
phylib to resolve PLCA get/set config and get status messages.
Signed-off-by: Piergiorgio Beruto <[email protected]>
---
drivers/net/phy/phy.c | 175 +++++++++++++++++++++++++++++++++++
drivers/net/phy/phy_device.c | 3 +
2 files changed, 178 insertions(+)
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index e5b6cb1a77f9..3fc251f5de26 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -543,6 +543,181 @@ int phy_ethtool_get_stats(struct phy_device *phydev,
}
EXPORT_SYMBOL(phy_ethtool_get_stats);
+/**
+ * phy_ethtool_get_plca_cfg - Get PLCA RS configuration
+ *
+ * @phydev: the phy_device struct
+ * @plca_cfg: where to store the retrieved configuration
+ */
+int phy_ethtool_get_plca_cfg(struct phy_device *phydev,
+ struct phy_plca_cfg *plca_cfg)
+{
+ int ret;
+
+ if (!phydev->drv) {
+ ret = -EIO;
+ goto out;
+ }
+
+ if (!phydev->drv->get_plca_cfg) {
+ ret = -EOPNOTSUPP;
+ goto out;
+ }
+
+ memset(plca_cfg, 0xFF, sizeof(*plca_cfg));
+
+ mutex_lock(&phydev->lock);
+ ret = phydev->drv->get_plca_cfg(phydev, plca_cfg);
+
+ if (ret)
+ goto out_drv;
+
+out_drv:
+ mutex_unlock(&phydev->lock);
+out:
+ return ret;
+}
+
+/**
+ * phy_ethtool_set_plca_cfg - Set PLCA RS configuration
+ *
+ * @phydev: the phy_device struct
+ * @extack: extack for reporting useful error messages
+ * @plca_cfg: new PLCA configuration to apply
+ */
+int phy_ethtool_set_plca_cfg(struct phy_device *phydev,
+ struct netlink_ext_ack *extack,
+ const struct phy_plca_cfg *plca_cfg)
+{
+ int ret;
+ struct phy_plca_cfg *curr_plca_cfg = 0;
+
+ if (!phydev->drv) {
+ ret = -EIO;
+ goto out;
+ }
+
+ if (!phydev->drv->set_plca_cfg ||
+ !phydev->drv->get_plca_cfg) {
+ ret = -EOPNOTSUPP;
+ goto out;
+ }
+
+ curr_plca_cfg = kmalloc(sizeof(*curr_plca_cfg), GFP_KERNEL);
+ memset(curr_plca_cfg, 0xFF, sizeof(*curr_plca_cfg));
+
+ mutex_lock(&phydev->lock);
+
+ ret = phydev->drv->get_plca_cfg(phydev, curr_plca_cfg);
+ if (ret)
+ goto out_drv;
+
+ if (curr_plca_cfg->enabled < 0 && plca_cfg->enabled >= 0) {
+ NL_SET_ERR_MSG(extack,
+ "PHY does not support changing the PLCA 'enable' attribute");
+ ret = -EINVAL;
+ goto out_drv;
+ }
+
+ if (curr_plca_cfg->node_id < 0 && plca_cfg->node_id >= 0) {
+ NL_SET_ERR_MSG(extack,
+ "PHY does not support changing the PLCA 'local node ID' attribute");
+ ret = -EINVAL;
+ goto out_drv;
+ }
+
+ if (curr_plca_cfg->node_cnt < 0 && plca_cfg->node_cnt >= 0) {
+ NL_SET_ERR_MSG(extack,
+ "PHY does not support changing the PLCA 'node count' attribute");
+ ret = -EINVAL;
+ goto out_drv;
+ }
+
+ if (curr_plca_cfg->to_tmr < 0 && plca_cfg->to_tmr >= 0) {
+ NL_SET_ERR_MSG(extack,
+ "PHY does not support changing the PLCA 'TO timer' attribute");
+ ret = -EINVAL;
+ goto out_drv;
+ }
+
+ if (curr_plca_cfg->burst_cnt < 0 && plca_cfg->burst_cnt >= 0) {
+ NL_SET_ERR_MSG(extack,
+ "PHY does not support changing the PLCA 'burst count' attribute");
+ ret = -EINVAL;
+ goto out_drv;
+ }
+
+ if (curr_plca_cfg->burst_tmr < 0 && plca_cfg->burst_tmr >= 0) {
+ NL_SET_ERR_MSG(extack,
+ "PHY does not support changing the PLCA 'burst timer' attribute");
+ ret = -EINVAL;
+ goto out_drv;
+ }
+
+ // if enabling PLCA, perform additional sanity checks
+ if (plca_cfg->enabled > 0) {
+ if (!linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half_BIT,
+ phydev->advertising)) {
+ ret = -EOPNOTSUPP;
+ NL_SET_ERR_MSG(extack,
+ "Point to Multi-Point mode is not enabled");
+ }
+
+ // allow setting node_id concurrently with enabled
+ if (plca_cfg->node_id >= 0)
+ curr_plca_cfg->node_id = plca_cfg->node_id;
+
+ if (curr_plca_cfg->node_id >= 255) {
+ NL_SET_ERR_MSG(extack, "PLCA node ID is not set");
+ ret = -EINVAL;
+ goto out_drv;
+ }
+ }
+
+ ret = phydev->drv->set_plca_cfg(phydev, plca_cfg);
+ if (ret)
+ goto out_drv;
+
+out_drv:
+ kfree(curr_plca_cfg);
+ mutex_unlock(&phydev->lock);
+out:
+ return ret;
+}
+
+/**
+ * phy_ethtool_get_plca_status - Get PLCA RS status information
+ *
+ * @phydev: the phy_device struct
+ * @plca_st: where to store the retrieved status information
+ */
+int phy_ethtool_get_plca_status(struct phy_device *phydev,
+ struct phy_plca_status *plca_st)
+{
+ int ret;
+
+ if (!phydev->drv) {
+ ret = -EIO;
+ goto out;
+ }
+
+ if (!phydev->drv->get_plca_status) {
+ ret = -EOPNOTSUPP;
+ goto out;
+ }
+
+ mutex_lock(&phydev->lock);
+ ret = phydev->drv->get_plca_status(phydev, plca_st);
+
+ if (ret)
+ goto out_drv;
+
+out_drv:
+ mutex_unlock(&phydev->lock);
+out:
+ return ret;
+}
+
/**
* phy_start_cable_test - Start a cable test
*
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 716870a4499c..f248010c403d 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -3262,6 +3262,9 @@ static const struct ethtool_phy_ops phy_ethtool_phy_ops = {
.get_sset_count = phy_ethtool_get_sset_count,
.get_strings = phy_ethtool_get_strings,
.get_stats = phy_ethtool_get_stats,
+ .get_plca_cfg = phy_ethtool_get_plca_cfg,
+ .set_plca_cfg = phy_ethtool_set_plca_cfg,
+ .get_plca_status = phy_ethtool_get_plca_status,
.start_cable_test = phy_start_cable_test,
.start_cable_test_tdr = phy_start_cable_test_tdr,
};
--
2.35.1