The codec driver needs correct regulators in order to probe.
Both VCC_3V3 and VCC_1V8 is always on fixed regulators on the board.
Signed-off-by: Peter Ujfalusi <[email protected]>
---
arch/arm/mach-davinci/board-dm365-evm.c | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c
index 150a36f333df..2328b15ac067 100644
--- a/arch/arm/mach-davinci/board-dm365-evm.c
+++ b/arch/arm/mach-davinci/board-dm365-evm.c
@@ -30,6 +30,8 @@
#include <linux/spi/eeprom.h>
#include <linux/v4l2-dv-timings.h>
#include <linux/platform_data/ti-aemif.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -245,6 +247,19 @@ static struct davinci_i2c_platform_data i2c_pdata = {
.bus_delay = 0 /* usec */,
};
+/* Fixed regulator support */
+static struct regulator_consumer_supply fixed_supplies_3_3v[] = {
+ /* Baseboard 3.3V: 5V -> TPS767D301 -> 3.3V */
+ REGULATOR_SUPPLY("AVDD", "1-0018"),
+ REGULATOR_SUPPLY("DRVDD", "1-0018"),
+ REGULATOR_SUPPLY("IOVDD", "1-0018"),
+};
+
+static struct regulator_consumer_supply fixed_supplies_1_8v[] = {
+ /* Baseboard 1.8V: 5V -> TPS767D301 -> 1.8V */
+ REGULATOR_SUPPLY("DVDD", "1-0018"),
+};
+
static int dm365evm_keyscan_enable(struct device *dev)
{
return davinci_cfg_reg(DM365_KEYSCAN);
@@ -800,6 +815,11 @@ static __init void dm365_evm_init(void)
if (ret)
pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
+ regulator_register_always_on(0, "fixed-dummy", fixed_supplies_1_8v,
+ ARRAY_SIZE(fixed_supplies_1_8v), 1800000);
+ regulator_register_always_on(1, "fixed-dummy", fixed_supplies_3_3v,
+ ARRAY_SIZE(fixed_supplies_3_3v), 3300000);
+
nvmem_add_cell_table(&davinci_nvmem_cell_table);
nvmem_add_cell_lookups(&davinci_nvmem_cell_lookup, 1);
--
Peter
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
On 30/08/19 3:52 PM, Peter Ujfalusi wrote:
> The codec driver needs correct regulators in order to probe.
> Both VCC_3V3 and VCC_1V8 is always on fixed regulators on the board.
>
> Signed-off-by: Peter Ujfalusi <[email protected]>
Applied for v5.4
Thanks,
Sekhar
On 17/10/19 4:39 PM, Sekhar Nori wrote:
> On 30/08/19 3:52 PM, Peter Ujfalusi wrote:
>> The codec driver needs correct regulators in order to probe.
>> Both VCC_3V3 and VCC_1V8 is always on fixed regulators on the board.
>>
>> Signed-off-by: Peter Ujfalusi <[email protected]>
>
> Applied for v5.4
This is breaking boot on DM365 EVM.
Booting Linux on physical CPU 0x0
Linux version 5.4.0-rc1-00001-g927d10a85791-dirty (a0875516@psplinux063) (gcc v9
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f
CPU: VIVT data cache, VIVT instruction cache
Machine: DaVinci DM365 EVM
Memory policy: Data cache writethrough
cma: Reserved 16 MiB at 0x86c00000
DaVinci dm365_rev1.1 variant 0x0
On node 0 totalpages: 32768
DMA zone: 256 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 32768 pages, LIFO batch:7
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0
Built 1 zonelists, mobility grouping on. Total pages: 32512
Kernel command line: console=ttyS0,115200n8 root=/dev/nfs rw nfsroot=172.24.210p
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
mem auto-init: stack:off, heap alloc:off, heap free:off
Memory: 106776K/131072K available (4760K kernel code, 253K rwdata, 1160K rodata)
SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
rcu: Preemptible hierarchical RCU implementation.
Tasks RCU enabled.
rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
random: get_random_bytes called from start_kernel+0x25c/0x440 with crng_init=0
clocksource: timer0_1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79s
sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
Console: colour dummy device 80x30
Calibrating delay loop... 146.84 BogoMIPS (lpj=734208)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x80008400 - 0x80008458
rcu: Hierarchical SRCU implementation.
devtmpfs: initialized
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 191s
futex hash table entries: 256 (order: -1, 3072 bytes, linear)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
mux: initialized INT_EDMA_CC
mux: Setting register INT_EDMA_CC
mux: INTMUX (0x00000018) = 0x00000000 -> 0x00000004
cpuidle: using governor menu
mux: initialized INT_EMAC_RXTHRESH
mux: Setting register INT_EMAC_RXTHRESH
mux: INTMUX (0x00000018) = 0x00000004 -> 0x00004004
mux: initialized INT_EMAC_RXPULSE
mux: Setting register INT_EMAC_RXPULSE
mux: INTMUX (0x00000018) = 0x00004004 -> 0x0000c004
mux: initialized INT_EMAC_TXPULSE
mux: Setting register INT_EMAC_TXPULSE
mux: INTMUX (0x00000018) = 0x0000c004 -> 0x0001c004
mux: initialized INT_EMAC_MISCPULSE
mux: Setting register INT_EMAC_MISCPULSE
mux: INTMUX (0x00000018) = 0x0001c004 -> 0x0003c004
EVM: tvp5146 SD video input
mux: initialized INT_PRTCSS
mux: Setting register INT_PRTCSS
mux: INTMUX (0x00000018) = 0x0003c004 -> 0x0003c404
mux: initialized SPI0_SCLK
mux: Setting register SPI0_SCLK
mux: PINMUX3 (0x0000000c) = 0x015affff -> 0x115affff
mux: initialized SPI0_SDI
mux: Setting register SPI0_SDI
mux: PINMUX3 (0x0000000c) = 0x115affff -> 0x155affff
mux: initialized SPI0_SDO
mux: Setting register SPI0_SDO
mux: PINMUX3 (0x0000000c) = 0x155affff -> 0x175affff
mux: initialized SPI0_SDENA0
mux: Setting register SPI0_SDENA0
mux: PINMUX3 (0x0000000c) = 0x175affff -> 0x375affff
edma edma.0: Legacy memcpy is enabled, things might not work
edma edma.0: TI EDMA DMA engine driver
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 000000c0
pgd = (ptrval)
[000000c0] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.4.0-rc1-00001-g927d10a85791-dirty #146
Hardware name: DaVinci DM365 EVM
PC is at reg_fixed_voltage_probe+0x30/0x2ec
LR is at reg_fixed_voltage_probe+0x2c/0x2ec
pc : [<c02a9628>] lr : [<c02a9624>] psr: 60000053
sp : c6837de0 ip : 00000000 fp : c062cfd8
r10: c05f44a8 r9 : 00000000 r8 : c68a24d0
r7 : c0631008 r6 : c68a24e0 r5 : 00000000 r4 : c68a24e0
r3 : 00000000 r2 : c065a854 r1 : 00000000 r0 : 00000000
Flags: nZCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none
Control: 0005317f Table: 80004000 DAC: 00000053
Process swapper (pid: 1, stack limit = 0x(ptrval))
Stack: (0xc6837de0 to 0xc6838000)
7de0: c689be40 c0167044 00000000 c68f4720 c68f4660 c68f4660 c68f4720 c689be40
7e00: c0575ca4 64d9cb0d 00000000 c68a24e0 00000000 c065a854 c065a854 00000000
7e20: 00000000 c05f44a8 c062cfd8 c02e0a64 c68a24e0 c0688d00 00000000 c02dec54
7e40: c68a24e0 c065a854 c065a854 c0631008 ffffe000 c061e828 c05f44a8 c02def44
7e60: 00000000 ffffff08 ffff0a00 c68a24e0 00000000 c065a854 c0631008 ffffe000
7e80: c061e828 c05f44a8 c062cfd8 c02df1f8 00000000 c065a854 c68a24e0 c02df258
7ea0: c68337b0 c065a854 c02df200 c02dced4 c061e828 c681db90 c68337b0 64d9cb0d
7ec0: c062cfd8 c065a854 c682af00 c065ea48 00000000 c02de070 c054f984 c0494cc0
7ee0: c065a854 c065a854 c0631008 c060b098 00000000 c02dfb04 c066d5c0 c0631008
7f00: c060b098 c000a624 0000007f c7fffea8 c05d00c4 00000000 c7fffee9 c00372e0
7f20: c05cf6d8 c0549714 00000000 00000004 00000004 00000000 00000000 c7fffee2
7f40: c7fffee5 64d9cb0d 00000000 0000007f c061e844 64d9cb0d 0000007f c061e848
7f60: 00000005 c066d5c0 c066d5c0 c05f4e6c 00000004 00000004 00000000 c05f44a8
7f80: 00000000 00000000 c04a71bc 00000000 00000000 00000000 00000000 00000000
7fa0: 00000000 c04a71c4 00000000 c00090e0 00000000 00000000 00000000 00000000
7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<c02a9628>] (reg_fixed_voltage_probe) from [<c02e0a64>] (platform_drv_probe+0x)
[<c02e0a64>] (platform_drv_probe) from [<c02dec54>] (really_probe+0x1e0/0x34c)
[<c02dec54>] (really_probe) from [<c02def44>] (driver_probe_device+0x5c/0x168)
[<c02def44>] (driver_probe_device) from [<c02df1f8>] (device_driver_attach+0x58)
[<c02df1f8>] (device_driver_attach) from [<c02df258>] (__driver_attach+0x58/0xc)
[<c02df258>] (__driver_attach) from [<c02dced4>] (bus_for_each_dev+0x70/0xb4)
[<c02dced4>] (bus_for_each_dev) from [<c02de070>] (bus_add_driver+0x194/0x1cc)
[<c02de070>] (bus_add_driver) from [<c02dfb04>] (driver_register+0x74/0x108)
[<c02dfb04>] (driver_register) from [<c000a624>] (do_one_initcall+0x6c/0x1d8)
[<c000a624>] (do_one_initcall) from [<c05f4e6c>] (kernel_init_freeable+0x10c/0x)
[<c05f4e6c>] (kernel_init_freeable) from [<c04a71c4>] (kernel_init+0x8/0xec)
[<c04a71c4>] (kernel_init) from [<c00090e0>] (ret_from_fork+0x14/0x34)
Exception stack(0xc6837fb0 to 0xc6837ff8)
7fa0: 00000000 00000000 00000000 00000000
7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7fe0: 00000000 00000000 00000000 00000000 00000013 00000000
Code: e5920018 e58d3024 eb02b71e e3a03000 (e59090c0)
---[ end trace 90e87368a248f7f6 ]---
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Thanks,
Sekhar
On 17/10/2019 16.49, Sekhar Nori wrote:
> On 17/10/19 4:39 PM, Sekhar Nori wrote:
>> On 30/08/19 3:52 PM, Peter Ujfalusi wrote:
>>> The codec driver needs correct regulators in order to probe.
>>> Both VCC_3V3 and VCC_1V8 is always on fixed regulators on the board.
>>>
>>> Signed-off-by: Peter Ujfalusi <[email protected]>
>>
>> Applied for v5.4
>
> This is breaking boot on DM365 EVM.
>
> Booting Linux on physical CPU 0x0
> Linux version 5.4.0-rc1-00001-g927d10a85791-dirty (a0875516@psplinux063) (gcc v9
> CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f
> CPU: VIVT data cache, VIVT instruction cache
> Machine: DaVinci DM365 EVM
> Memory policy: Data cache writethrough
> cma: Reserved 16 MiB at 0x86c00000
> DaVinci dm365_rev1.1 variant 0x0
> On node 0 totalpages: 32768
> DMA zone: 256 pages used for memmap
> DMA zone: 0 pages reserved
> DMA zone: 32768 pages, LIFO batch:7
> pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
> pcpu-alloc: [0] 0
> Built 1 zonelists, mobility grouping on. Total pages: 32512
> Kernel command line: console=ttyS0,115200n8 root=/dev/nfs rw nfsroot=172.24.210p
> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
> mem auto-init: stack:off, heap alloc:off, heap free:off
> Memory: 106776K/131072K available (4760K kernel code, 253K rwdata, 1160K rodata)
> SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> rcu: Preemptible hierarchical RCU implementation.
> Tasks RCU enabled.
> rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
> NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
> random: get_random_bytes called from start_kernel+0x25c/0x440 with crng_init=0
> clocksource: timer0_1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79s
> sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
> Console: colour dummy device 80x30
> Calibrating delay loop... 146.84 BogoMIPS (lpj=734208)
> pid_max: default: 32768 minimum: 301
> Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
> Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
> CPU: Testing write buffer coherency: ok
> Setting up static identity map for 0x80008400 - 0x80008458
> rcu: Hierarchical SRCU implementation.
> devtmpfs: initialized
> clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 191s
> futex hash table entries: 256 (order: -1, 3072 bytes, linear)
> pinctrl core: initialized pinctrl subsystem
> NET: Registered protocol family 16
> DMA: preallocated 256 KiB pool for atomic coherent allocations
> mux: initialized INT_EDMA_CC
> mux: Setting register INT_EDMA_CC
> mux: INTMUX (0x00000018) = 0x00000000 -> 0x00000004
> cpuidle: using governor menu
> mux: initialized INT_EMAC_RXTHRESH
> mux: Setting register INT_EMAC_RXTHRESH
> mux: INTMUX (0x00000018) = 0x00000004 -> 0x00004004
> mux: initialized INT_EMAC_RXPULSE
> mux: Setting register INT_EMAC_RXPULSE
> mux: INTMUX (0x00000018) = 0x00004004 -> 0x0000c004
> mux: initialized INT_EMAC_TXPULSE
> mux: Setting register INT_EMAC_TXPULSE
> mux: INTMUX (0x00000018) = 0x0000c004 -> 0x0001c004
> mux: initialized INT_EMAC_MISCPULSE
> mux: Setting register INT_EMAC_MISCPULSE
> mux: INTMUX (0x00000018) = 0x0001c004 -> 0x0003c004
> EVM: tvp5146 SD video input
> mux: initialized INT_PRTCSS
> mux: Setting register INT_PRTCSS
> mux: INTMUX (0x00000018) = 0x0003c004 -> 0x0003c404
> mux: initialized SPI0_SCLK
> mux: Setting register SPI0_SCLK
> mux: PINMUX3 (0x0000000c) = 0x015affff -> 0x115affff
> mux: initialized SPI0_SDI
> mux: Setting register SPI0_SDI
> mux: PINMUX3 (0x0000000c) = 0x115affff -> 0x155affff
> mux: initialized SPI0_SDO
> mux: Setting register SPI0_SDO
> mux: PINMUX3 (0x0000000c) = 0x155affff -> 0x175affff
> mux: initialized SPI0_SDENA0
> mux: Setting register SPI0_SDENA0
> mux: PINMUX3 (0x0000000c) = 0x175affff -> 0x375affff
> edma edma.0: Legacy memcpy is enabled, things might not work
> edma edma.0: TI EDMA DMA engine driver
> 8<--- cut here ---
> Unable to handle kernel NULL pointer dereference at virtual address 000000c0
> pgd = (ptrval)
> [000000c0] *pgd=00000000
> Internal error: Oops: 5 [#1] PREEMPT ARM
> Modules linked in:
> CPU: 0 PID: 1 Comm: swapper Not tainted 5.4.0-rc1-00001-g927d10a85791-dirty #146
> Hardware name: DaVinci DM365 EVM
> PC is at reg_fixed_voltage_probe+0x30/0x2ec
> LR is at reg_fixed_voltage_probe+0x2c/0x2ec
> pc : [<c02a9628>] lr : [<c02a9624>] psr: 60000053
> sp : c6837de0 ip : 00000000 fp : c062cfd8
> r10: c05f44a8 r9 : 00000000 r8 : c68a24d0
> r7 : c0631008 r6 : c68a24e0 r5 : 00000000 r4 : c68a24e0
> r3 : 00000000 r2 : c065a854 r1 : 00000000 r0 : 00000000
> Flags: nZCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none
> Control: 0005317f Table: 80004000 DAC: 00000053
> Process swapper (pid: 1, stack limit = 0x(ptrval))
> Stack: (0xc6837de0 to 0xc6838000)
> 7de0: c689be40 c0167044 00000000 c68f4720 c68f4660 c68f4660 c68f4720 c689be40
> 7e00: c0575ca4 64d9cb0d 00000000 c68a24e0 00000000 c065a854 c065a854 00000000
> 7e20: 00000000 c05f44a8 c062cfd8 c02e0a64 c68a24e0 c0688d00 00000000 c02dec54
> 7e40: c68a24e0 c065a854 c065a854 c0631008 ffffe000 c061e828 c05f44a8 c02def44
> 7e60: 00000000 ffffff08 ffff0a00 c68a24e0 00000000 c065a854 c0631008 ffffe000
> 7e80: c061e828 c05f44a8 c062cfd8 c02df1f8 00000000 c065a854 c68a24e0 c02df258
> 7ea0: c68337b0 c065a854 c02df200 c02dced4 c061e828 c681db90 c68337b0 64d9cb0d
> 7ec0: c062cfd8 c065a854 c682af00 c065ea48 00000000 c02de070 c054f984 c0494cc0
> 7ee0: c065a854 c065a854 c0631008 c060b098 00000000 c02dfb04 c066d5c0 c0631008
> 7f00: c060b098 c000a624 0000007f c7fffea8 c05d00c4 00000000 c7fffee9 c00372e0
> 7f20: c05cf6d8 c0549714 00000000 00000004 00000004 00000000 00000000 c7fffee2
> 7f40: c7fffee5 64d9cb0d 00000000 0000007f c061e844 64d9cb0d 0000007f c061e848
> 7f60: 00000005 c066d5c0 c066d5c0 c05f4e6c 00000004 00000004 00000000 c05f44a8
> 7f80: 00000000 00000000 c04a71bc 00000000 00000000 00000000 00000000 00000000
> 7fa0: 00000000 c04a71c4 00000000 c00090e0 00000000 00000000 00000000 00000000
> 7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
> 7fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
> [<c02a9628>] (reg_fixed_voltage_probe) from [<c02e0a64>] (platform_drv_probe+0x)
> [<c02e0a64>] (platform_drv_probe) from [<c02dec54>] (really_probe+0x1e0/0x34c)
> [<c02dec54>] (really_probe) from [<c02def44>] (driver_probe_device+0x5c/0x168)
> [<c02def44>] (driver_probe_device) from [<c02df1f8>] (device_driver_attach+0x58)
> [<c02df1f8>] (device_driver_attach) from [<c02df258>] (__driver_attach+0x58/0xc)
> [<c02df258>] (__driver_attach) from [<c02dced4>] (bus_for_each_dev+0x70/0xb4)
> [<c02dced4>] (bus_for_each_dev) from [<c02de070>] (bus_add_driver+0x194/0x1cc)
> [<c02de070>] (bus_add_driver) from [<c02dfb04>] (driver_register+0x74/0x108)
> [<c02dfb04>] (driver_register) from [<c000a624>] (do_one_initcall+0x6c/0x1d8)
> [<c000a624>] (do_one_initcall) from [<c05f4e6c>] (kernel_init_freeable+0x10c/0x)
> [<c05f4e6c>] (kernel_init_freeable) from [<c04a71c4>] (kernel_init+0x8/0xec)
> [<c04a71c4>] (kernel_init) from [<c00090e0>] (ret_from_fork+0x14/0x34)
> Exception stack(0xc6837fb0 to 0xc6837ff8)
> 7fa0: 00000000 00000000 00000000 00000000
> 7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
> 7fe0: 00000000 00000000 00000000 00000000 00000013 00000000
> Code: e5920018 e58d3024 eb02b71e e3a03000 (e59090c0)
> ---[ end trace 90e87368a248f7f6 ]---
> Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Interesting.
Something has changed in regulators core which causes crash when not
booted with DT?
It did worked when I have sent the patches. I'll take a look what might
be the issue.
Same for the dma644x
- Péter
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
On 21/10/2019 13.40, Peter Ujfalusi wrote:
>
>
> On 17/10/2019 16.49, Sekhar Nori wrote:
>> On 17/10/19 4:39 PM, Sekhar Nori wrote:
>>> On 30/08/19 3:52 PM, Peter Ujfalusi wrote:
>>>> The codec driver needs correct regulators in order to probe.
>>>> Both VCC_3V3 and VCC_1V8 is always on fixed regulators on the board.
>>>>
>>>> Signed-off-by: Peter Ujfalusi <[email protected]>
>>>
>>> Applied for v5.4
>>
>> This is breaking boot on DM365 EVM.
>>
>> Booting Linux on physical CPU 0x0
>> Linux version 5.4.0-rc1-00001-g927d10a85791-dirty (a0875516@psplinux063) (gcc v9
>> CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f
>> CPU: VIVT data cache, VIVT instruction cache
>> Machine: DaVinci DM365 EVM
>> Memory policy: Data cache writethrough
>> cma: Reserved 16 MiB at 0x86c00000
>> DaVinci dm365_rev1.1 variant 0x0
>> On node 0 totalpages: 32768
>> DMA zone: 256 pages used for memmap
>> DMA zone: 0 pages reserved
>> DMA zone: 32768 pages, LIFO batch:7
>> pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
>> pcpu-alloc: [0] 0
>> Built 1 zonelists, mobility grouping on. Total pages: 32512
>> Kernel command line: console=ttyS0,115200n8 root=/dev/nfs rw nfsroot=172.24.210p
>> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
>> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
>> mem auto-init: stack:off, heap alloc:off, heap free:off
>> Memory: 106776K/131072K available (4760K kernel code, 253K rwdata, 1160K rodata)
>> SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
>> rcu: Preemptible hierarchical RCU implementation.
>> Tasks RCU enabled.
>> rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
>> NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
>> random: get_random_bytes called from start_kernel+0x25c/0x440 with crng_init=0
>> clocksource: timer0_1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79s
>> sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
>> Console: colour dummy device 80x30
>> Calibrating delay loop... 146.84 BogoMIPS (lpj=734208)
>> pid_max: default: 32768 minimum: 301
>> Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
>> Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
>> CPU: Testing write buffer coherency: ok
>> Setting up static identity map for 0x80008400 - 0x80008458
>> rcu: Hierarchical SRCU implementation.
>> devtmpfs: initialized
>> clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 191s
>> futex hash table entries: 256 (order: -1, 3072 bytes, linear)
>> pinctrl core: initialized pinctrl subsystem
>> NET: Registered protocol family 16
>> DMA: preallocated 256 KiB pool for atomic coherent allocations
>> mux: initialized INT_EDMA_CC
>> mux: Setting register INT_EDMA_CC
>> mux: INTMUX (0x00000018) = 0x00000000 -> 0x00000004
>> cpuidle: using governor menu
>> mux: initialized INT_EMAC_RXTHRESH
>> mux: Setting register INT_EMAC_RXTHRESH
>> mux: INTMUX (0x00000018) = 0x00000004 -> 0x00004004
>> mux: initialized INT_EMAC_RXPULSE
>> mux: Setting register INT_EMAC_RXPULSE
>> mux: INTMUX (0x00000018) = 0x00004004 -> 0x0000c004
>> mux: initialized INT_EMAC_TXPULSE
>> mux: Setting register INT_EMAC_TXPULSE
>> mux: INTMUX (0x00000018) = 0x0000c004 -> 0x0001c004
>> mux: initialized INT_EMAC_MISCPULSE
>> mux: Setting register INT_EMAC_MISCPULSE
>> mux: INTMUX (0x00000018) = 0x0001c004 -> 0x0003c004
>> EVM: tvp5146 SD video input
>> mux: initialized INT_PRTCSS
>> mux: Setting register INT_PRTCSS
>> mux: INTMUX (0x00000018) = 0x0003c004 -> 0x0003c404
>> mux: initialized SPI0_SCLK
>> mux: Setting register SPI0_SCLK
>> mux: PINMUX3 (0x0000000c) = 0x015affff -> 0x115affff
>> mux: initialized SPI0_SDI
>> mux: Setting register SPI0_SDI
>> mux: PINMUX3 (0x0000000c) = 0x115affff -> 0x155affff
>> mux: initialized SPI0_SDO
>> mux: Setting register SPI0_SDO
>> mux: PINMUX3 (0x0000000c) = 0x155affff -> 0x175affff
>> mux: initialized SPI0_SDENA0
>> mux: Setting register SPI0_SDENA0
>> mux: PINMUX3 (0x0000000c) = 0x175affff -> 0x375affff
>> edma edma.0: Legacy memcpy is enabled, things might not work
>> edma edma.0: TI EDMA DMA engine driver
>> 8<--- cut here ---
>> Unable to handle kernel NULL pointer dereference at virtual address 000000c0
>> pgd = (ptrval)
>> [000000c0] *pgd=00000000
>> Internal error: Oops: 5 [#1] PREEMPT ARM
>> Modules linked in:
>> CPU: 0 PID: 1 Comm: swapper Not tainted 5.4.0-rc1-00001-g927d10a85791-dirty #146
>> Hardware name: DaVinci DM365 EVM
>> PC is at reg_fixed_voltage_probe+0x30/0x2ec
>> LR is at reg_fixed_voltage_probe+0x2c/0x2ec
>> pc : [<c02a9628>] lr : [<c02a9624>] psr: 60000053
>> sp : c6837de0 ip : 00000000 fp : c062cfd8
>> r10: c05f44a8 r9 : 00000000 r8 : c68a24d0
>> r7 : c0631008 r6 : c68a24e0 r5 : 00000000 r4 : c68a24e0
>> r3 : 00000000 r2 : c065a854 r1 : 00000000 r0 : 00000000
>> Flags: nZCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none
>> Control: 0005317f Table: 80004000 DAC: 00000053
>> Process swapper (pid: 1, stack limit = 0x(ptrval))
>> Stack: (0xc6837de0 to 0xc6838000)
>> 7de0: c689be40 c0167044 00000000 c68f4720 c68f4660 c68f4660 c68f4720 c689be40
>> 7e00: c0575ca4 64d9cb0d 00000000 c68a24e0 00000000 c065a854 c065a854 00000000
>> 7e20: 00000000 c05f44a8 c062cfd8 c02e0a64 c68a24e0 c0688d00 00000000 c02dec54
>> 7e40: c68a24e0 c065a854 c065a854 c0631008 ffffe000 c061e828 c05f44a8 c02def44
>> 7e60: 00000000 ffffff08 ffff0a00 c68a24e0 00000000 c065a854 c0631008 ffffe000
>> 7e80: c061e828 c05f44a8 c062cfd8 c02df1f8 00000000 c065a854 c68a24e0 c02df258
>> 7ea0: c68337b0 c065a854 c02df200 c02dced4 c061e828 c681db90 c68337b0 64d9cb0d
>> 7ec0: c062cfd8 c065a854 c682af00 c065ea48 00000000 c02de070 c054f984 c0494cc0
>> 7ee0: c065a854 c065a854 c0631008 c060b098 00000000 c02dfb04 c066d5c0 c0631008
>> 7f00: c060b098 c000a624 0000007f c7fffea8 c05d00c4 00000000 c7fffee9 c00372e0
>> 7f20: c05cf6d8 c0549714 00000000 00000004 00000004 00000000 00000000 c7fffee2
>> 7f40: c7fffee5 64d9cb0d 00000000 0000007f c061e844 64d9cb0d 0000007f c061e848
>> 7f60: 00000005 c066d5c0 c066d5c0 c05f4e6c 00000004 00000004 00000000 c05f44a8
>> 7f80: 00000000 00000000 c04a71bc 00000000 00000000 00000000 00000000 00000000
>> 7fa0: 00000000 c04a71c4 00000000 c00090e0 00000000 00000000 00000000 00000000
>> 7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
>> 7fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
>> [<c02a9628>] (reg_fixed_voltage_probe) from [<c02e0a64>] (platform_drv_probe+0x)
>> [<c02e0a64>] (platform_drv_probe) from [<c02dec54>] (really_probe+0x1e0/0x34c)
>> [<c02dec54>] (really_probe) from [<c02def44>] (driver_probe_device+0x5c/0x168)
>> [<c02def44>] (driver_probe_device) from [<c02df1f8>] (device_driver_attach+0x58)
>> [<c02df1f8>] (device_driver_attach) from [<c02df258>] (__driver_attach+0x58/0xc)
>> [<c02df258>] (__driver_attach) from [<c02dced4>] (bus_for_each_dev+0x70/0xb4)
>> [<c02dced4>] (bus_for_each_dev) from [<c02de070>] (bus_add_driver+0x194/0x1cc)
>> [<c02de070>] (bus_add_driver) from [<c02dfb04>] (driver_register+0x74/0x108)
>> [<c02dfb04>] (driver_register) from [<c000a624>] (do_one_initcall+0x6c/0x1d8)
>> [<c000a624>] (do_one_initcall) from [<c05f4e6c>] (kernel_init_freeable+0x10c/0x)
>> [<c05f4e6c>] (kernel_init_freeable) from [<c04a71c4>] (kernel_init+0x8/0xec)
>> [<c04a71c4>] (kernel_init) from [<c00090e0>] (ret_from_fork+0x14/0x34)
>> Exception stack(0xc6837fb0 to 0xc6837ff8)
>> 7fa0: 00000000 00000000 00000000 00000000
>> 7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
>> 7fe0: 00000000 00000000 00000000 00000000 00000013 00000000
>> Code: e5920018 e58d3024 eb02b71e e3a03000 (e59090c0)
>> ---[ end trace 90e87368a248f7f6 ]---
>> Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
>
> Interesting.
> Something has changed in regulators core which causes crash when not
> booted with DT?
>
> It did worked when I have sent the patches. I'll take a look what might
> be the issue.
can this be the fix: https://lkml.org/lkml/2019/9/21/199 ?
>
> Same for the dma644x
>
> - Péter
>
> Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
> Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
>
> _______________________________________________
> linux-arm-kernel mailing list
> [email protected]
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
- Péter
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
On 22/10/19 1:12 PM, Peter Ujfalusi wrote:
>
>
> On 21/10/2019 13.40, Peter Ujfalusi wrote:
>>
>>
>> On 17/10/2019 16.49, Sekhar Nori wrote:
>>> On 17/10/19 4:39 PM, Sekhar Nori wrote:
>>>> On 30/08/19 3:52 PM, Peter Ujfalusi wrote:
>>>>> The codec driver needs correct regulators in order to probe.
>>>>> Both VCC_3V3 and VCC_1V8 is always on fixed regulators on the board.
>>>>>
>>>>> Signed-off-by: Peter Ujfalusi <[email protected]>
>>>>
>>>> Applied for v5.4
>>>
>>> This is breaking boot on DM365 EVM.
>>>
>>> Booting Linux on physical CPU 0x0
>>> Linux version 5.4.0-rc1-00001-g927d10a85791-dirty (a0875516@psplinux063) (gcc v9
>>> CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f
>>> CPU: VIVT data cache, VIVT instruction cache
>>> Machine: DaVinci DM365 EVM
>>> Memory policy: Data cache writethrough
>>> cma: Reserved 16 MiB at 0x86c00000
>>> DaVinci dm365_rev1.1 variant 0x0
>>> On node 0 totalpages: 32768
>>> DMA zone: 256 pages used for memmap
>>> DMA zone: 0 pages reserved
>>> DMA zone: 32768 pages, LIFO batch:7
>>> pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
>>> pcpu-alloc: [0] 0
>>> Built 1 zonelists, mobility grouping on. Total pages: 32512
>>> Kernel command line: console=ttyS0,115200n8 root=/dev/nfs rw nfsroot=172.24.210p
>>> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
>>> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
>>> mem auto-init: stack:off, heap alloc:off, heap free:off
>>> Memory: 106776K/131072K available (4760K kernel code, 253K rwdata, 1160K rodata)
>>> SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
>>> rcu: Preemptible hierarchical RCU implementation.
>>> Tasks RCU enabled.
>>> rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
>>> NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
>>> random: get_random_bytes called from start_kernel+0x25c/0x440 with crng_init=0
>>> clocksource: timer0_1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79s
>>> sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
>>> Console: colour dummy device 80x30
>>> Calibrating delay loop... 146.84 BogoMIPS (lpj=734208)
>>> pid_max: default: 32768 minimum: 301
>>> Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
>>> Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
>>> CPU: Testing write buffer coherency: ok
>>> Setting up static identity map for 0x80008400 - 0x80008458
>>> rcu: Hierarchical SRCU implementation.
>>> devtmpfs: initialized
>>> clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 191s
>>> futex hash table entries: 256 (order: -1, 3072 bytes, linear)
>>> pinctrl core: initialized pinctrl subsystem
>>> NET: Registered protocol family 16
>>> DMA: preallocated 256 KiB pool for atomic coherent allocations
>>> mux: initialized INT_EDMA_CC
>>> mux: Setting register INT_EDMA_CC
>>> mux: INTMUX (0x00000018) = 0x00000000 -> 0x00000004
>>> cpuidle: using governor menu
>>> mux: initialized INT_EMAC_RXTHRESH
>>> mux: Setting register INT_EMAC_RXTHRESH
>>> mux: INTMUX (0x00000018) = 0x00000004 -> 0x00004004
>>> mux: initialized INT_EMAC_RXPULSE
>>> mux: Setting register INT_EMAC_RXPULSE
>>> mux: INTMUX (0x00000018) = 0x00004004 -> 0x0000c004
>>> mux: initialized INT_EMAC_TXPULSE
>>> mux: Setting register INT_EMAC_TXPULSE
>>> mux: INTMUX (0x00000018) = 0x0000c004 -> 0x0001c004
>>> mux: initialized INT_EMAC_MISCPULSE
>>> mux: Setting register INT_EMAC_MISCPULSE
>>> mux: INTMUX (0x00000018) = 0x0001c004 -> 0x0003c004
>>> EVM: tvp5146 SD video input
>>> mux: initialized INT_PRTCSS
>>> mux: Setting register INT_PRTCSS
>>> mux: INTMUX (0x00000018) = 0x0003c004 -> 0x0003c404
>>> mux: initialized SPI0_SCLK
>>> mux: Setting register SPI0_SCLK
>>> mux: PINMUX3 (0x0000000c) = 0x015affff -> 0x115affff
>>> mux: initialized SPI0_SDI
>>> mux: Setting register SPI0_SDI
>>> mux: PINMUX3 (0x0000000c) = 0x115affff -> 0x155affff
>>> mux: initialized SPI0_SDO
>>> mux: Setting register SPI0_SDO
>>> mux: PINMUX3 (0x0000000c) = 0x155affff -> 0x175affff
>>> mux: initialized SPI0_SDENA0
>>> mux: Setting register SPI0_SDENA0
>>> mux: PINMUX3 (0x0000000c) = 0x175affff -> 0x375affff
>>> edma edma.0: Legacy memcpy is enabled, things might not work
>>> edma edma.0: TI EDMA DMA engine driver
>>> 8<--- cut here ---
>>> Unable to handle kernel NULL pointer dereference at virtual address 000000c0
>>> pgd = (ptrval)
>>> [000000c0] *pgd=00000000
>>> Internal error: Oops: 5 [#1] PREEMPT ARM
>>> Modules linked in:
>>> CPU: 0 PID: 1 Comm: swapper Not tainted 5.4.0-rc1-00001-g927d10a85791-dirty #146
>>> Hardware name: DaVinci DM365 EVM
>>> PC is at reg_fixed_voltage_probe+0x30/0x2ec
>>> LR is at reg_fixed_voltage_probe+0x2c/0x2ec
>>> pc : [<c02a9628>] lr : [<c02a9624>] psr: 60000053
>>> sp : c6837de0 ip : 00000000 fp : c062cfd8
>>> r10: c05f44a8 r9 : 00000000 r8 : c68a24d0
>>> r7 : c0631008 r6 : c68a24e0 r5 : 00000000 r4 : c68a24e0
>>> r3 : 00000000 r2 : c065a854 r1 : 00000000 r0 : 00000000
>>> Flags: nZCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none
>>> Control: 0005317f Table: 80004000 DAC: 00000053
>>> Process swapper (pid: 1, stack limit = 0x(ptrval))
>>> Stack: (0xc6837de0 to 0xc6838000)
>>> 7de0: c689be40 c0167044 00000000 c68f4720 c68f4660 c68f4660 c68f4720 c689be40
>>> 7e00: c0575ca4 64d9cb0d 00000000 c68a24e0 00000000 c065a854 c065a854 00000000
>>> 7e20: 00000000 c05f44a8 c062cfd8 c02e0a64 c68a24e0 c0688d00 00000000 c02dec54
>>> 7e40: c68a24e0 c065a854 c065a854 c0631008 ffffe000 c061e828 c05f44a8 c02def44
>>> 7e60: 00000000 ffffff08 ffff0a00 c68a24e0 00000000 c065a854 c0631008 ffffe000
>>> 7e80: c061e828 c05f44a8 c062cfd8 c02df1f8 00000000 c065a854 c68a24e0 c02df258
>>> 7ea0: c68337b0 c065a854 c02df200 c02dced4 c061e828 c681db90 c68337b0 64d9cb0d
>>> 7ec0: c062cfd8 c065a854 c682af00 c065ea48 00000000 c02de070 c054f984 c0494cc0
>>> 7ee0: c065a854 c065a854 c0631008 c060b098 00000000 c02dfb04 c066d5c0 c0631008
>>> 7f00: c060b098 c000a624 0000007f c7fffea8 c05d00c4 00000000 c7fffee9 c00372e0
>>> 7f20: c05cf6d8 c0549714 00000000 00000004 00000004 00000000 00000000 c7fffee2
>>> 7f40: c7fffee5 64d9cb0d 00000000 0000007f c061e844 64d9cb0d 0000007f c061e848
>>> 7f60: 00000005 c066d5c0 c066d5c0 c05f4e6c 00000004 00000004 00000000 c05f44a8
>>> 7f80: 00000000 00000000 c04a71bc 00000000 00000000 00000000 00000000 00000000
>>> 7fa0: 00000000 c04a71c4 00000000 c00090e0 00000000 00000000 00000000 00000000
>>> 7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
>>> 7fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
>>> [<c02a9628>] (reg_fixed_voltage_probe) from [<c02e0a64>] (platform_drv_probe+0x)
>>> [<c02e0a64>] (platform_drv_probe) from [<c02dec54>] (really_probe+0x1e0/0x34c)
>>> [<c02dec54>] (really_probe) from [<c02def44>] (driver_probe_device+0x5c/0x168)
>>> [<c02def44>] (driver_probe_device) from [<c02df1f8>] (device_driver_attach+0x58)
>>> [<c02df1f8>] (device_driver_attach) from [<c02df258>] (__driver_attach+0x58/0xc)
>>> [<c02df258>] (__driver_attach) from [<c02dced4>] (bus_for_each_dev+0x70/0xb4)
>>> [<c02dced4>] (bus_for_each_dev) from [<c02de070>] (bus_add_driver+0x194/0x1cc)
>>> [<c02de070>] (bus_add_driver) from [<c02dfb04>] (driver_register+0x74/0x108)
>>> [<c02dfb04>] (driver_register) from [<c000a624>] (do_one_initcall+0x6c/0x1d8)
>>> [<c000a624>] (do_one_initcall) from [<c05f4e6c>] (kernel_init_freeable+0x10c/0x)
>>> [<c05f4e6c>] (kernel_init_freeable) from [<c04a71c4>] (kernel_init+0x8/0xec)
>>> [<c04a71c4>] (kernel_init) from [<c00090e0>] (ret_from_fork+0x14/0x34)
>>> Exception stack(0xc6837fb0 to 0xc6837ff8)
>>> 7fa0: 00000000 00000000 00000000 00000000
>>> 7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
>>> 7fe0: 00000000 00000000 00000000 00000000 00000013 00000000
>>> Code: e5920018 e58d3024 eb02b71e e3a03000 (e59090c0)
>>> ---[ end trace 90e87368a248f7f6 ]---
>>> Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
>>
>> Interesting.
>> Something has changed in regulators core which causes crash when not
>> booted with DT?
>>
>> It did worked when I have sent the patches. I'll take a look what might
>> be the issue.
>
> can this be the fix: https://lkml.org/lkml/2019/9/21/199 ?
It seems like, and I confirm it works now! Queuing for v5.6
Thanks,
Sekhar