From: Ondrej Jirman <[email protected]>
This series adds support for jack detection to this codec. I used
and tested this on Pinephone. It works quite nicely. I tested it
against Android headset mic button resistor specification.
The patches are a rewritten and debugged version of the original
ones from Arnaud Ferraris and Samuel Holland, improved to better
handle headset button presses and with more robust plug-in/out
event debouncing, and to use set_jack API instead of sniffing
the sound card widget names, to detect the type of jack connector.
Please take a look. :)
v3:
- removed all device-tree related code
(it's not necessary for core functionality, it only helps make the jack detect
functionality of the codec be usable from simple-sound-card driver, and I'll
send it spearately, because it will apparently need several more rounds
of review)
v2:
- use set_jack/get_jack_type
- get rid of some custom poking inside card internals to figure
out what kind of jack port we should setup the codec for
- read jack-type from OF as suggested here:
https://elixir.bootlin.com/linux/latest/source/sound/soc/soc-component.c#L288
- add DT bindings
Thank you very much,
Ondřej Jirman
Arnaud Ferraris (2):
ASoC: sun50i-codec-analog: Enable jack detection on startup
ASoC: sun8i-codec: Implement jack and accessory detection
Samuel Holland (2):
ASoC: sun50i-codec-analog: Move suspend/resume to set_bias_level
ASoC: sun8i-codec: Enable bus clock at STANDBY and higher bias
sound/soc/sunxi/sun50i-codec-analog.c | 73 +++++-
sound/soc/sunxi/sun8i-codec.c | 346 +++++++++++++++++++++++++-
2 files changed, 399 insertions(+), 20 deletions(-)
--
2.44.0
From: Arnaud Ferraris <[email protected]>
This commit adds the necessary setup to enable jack detection on startup
as well as the callback function enabling the microphone ADC when
headset bias is enabled. The microphone ADC is also disabled in suspend.
Signed-off-by: Arnaud Ferraris <[email protected]>
[Samuel: Moved MICADCEN setup to HBIAS event, added bias hooks]
Signed-off-by: Samuel Holland <[email protected]>
Signed-off-by: Ondřej Jirman <[email protected]>
---
sound/soc/sunxi/sun50i-codec-analog.c | 32 ++++++++++++++++++++++++++-
1 file changed, 31 insertions(+), 1 deletion(-)
diff --git a/sound/soc/sunxi/sun50i-codec-analog.c b/sound/soc/sunxi/sun50i-codec-analog.c
index cedd4de42d1a..2081721a8ff2 100644
--- a/sound/soc/sunxi/sun50i-codec-analog.c
+++ b/sound/soc/sunxi/sun50i-codec-analog.c
@@ -116,8 +116,10 @@
#define SUN50I_ADDA_HS_MBIAS_CTRL_MMICBIASEN 7
#define SUN50I_ADDA_JACK_MIC_CTRL 0x1d
+#define SUN50I_ADDA_JACK_MIC_CTRL_JACKDETEN 7
#define SUN50I_ADDA_JACK_MIC_CTRL_INNERRESEN 6
#define SUN50I_ADDA_JACK_MIC_CTRL_HMICBIASEN 5
+#define SUN50I_ADDA_JACK_MIC_CTRL_MICADCEN 4
/* mixer controls */
static const struct snd_kcontrol_new sun50i_a64_codec_mixer_controls[] = {
@@ -296,6 +298,19 @@ static const struct snd_kcontrol_new sun50i_codec_earpiece_switch[] = {
SUN50I_ADDA_EARPIECE_CTRL1_ESPPA_MUTE, 1, 0),
};
+static int sun50i_codec_hbias_event(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *kcontrol, int event)
+{
+ struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
+ u32 value = !!SND_SOC_DAPM_EVENT_ON(event);
+
+ regmap_update_bits(component->regmap, SUN50I_ADDA_JACK_MIC_CTRL,
+ BIT(SUN50I_ADDA_JACK_MIC_CTRL_MICADCEN),
+ value << SUN50I_ADDA_JACK_MIC_CTRL_MICADCEN);
+
+ return 0;
+}
+
static const struct snd_soc_dapm_widget sun50i_a64_codec_widgets[] = {
/* DAC */
SND_SOC_DAPM_DAC("Left DAC", NULL, SUN50I_ADDA_MIX_DAC_CTRL,
@@ -367,7 +382,8 @@ static const struct snd_soc_dapm_widget sun50i_a64_codec_widgets[] = {
/* Microphone Bias */
SND_SOC_DAPM_SUPPLY("HBIAS", SUN50I_ADDA_JACK_MIC_CTRL,
SUN50I_ADDA_JACK_MIC_CTRL_HMICBIASEN,
- 0, NULL, 0),
+ 0, sun50i_codec_hbias_event,
+ SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),
/* Mic input path */
SND_SOC_DAPM_PGA("Mic2 Amplifier", SUN50I_ADDA_MIC2_CTRL,
@@ -474,14 +490,28 @@ static const struct snd_soc_dapm_route sun50i_a64_codec_routes[] = {
static int sun50i_a64_codec_set_bias_level(struct snd_soc_component *component,
enum snd_soc_bias_level level)
{
+ struct snd_soc_dapm_context *dapm = snd_soc_component_get_dapm(component);
+ int hbias;
+
switch (level) {
case SND_SOC_BIAS_OFF:
+ regmap_clear_bits(component->regmap, SUN50I_ADDA_JACK_MIC_CTRL,
+ BIT(SUN50I_ADDA_JACK_MIC_CTRL_JACKDETEN) |
+ BIT(SUN50I_ADDA_JACK_MIC_CTRL_MICADCEN));
+
regmap_set_bits(component->regmap, SUN50I_ADDA_HP_CTRL,
BIT(SUN50I_ADDA_HP_CTRL_PA_CLK_GATE));
break;
case SND_SOC_BIAS_STANDBY:
regmap_clear_bits(component->regmap, SUN50I_ADDA_HP_CTRL,
BIT(SUN50I_ADDA_HP_CTRL_PA_CLK_GATE));
+
+ hbias = snd_soc_dapm_get_pin_status(dapm, "HBIAS");
+ regmap_update_bits(component->regmap, SUN50I_ADDA_JACK_MIC_CTRL,
+ BIT(SUN50I_ADDA_JACK_MIC_CTRL_JACKDETEN) |
+ BIT(SUN50I_ADDA_JACK_MIC_CTRL_MICADCEN),
+ BIT(SUN50I_ADDA_JACK_MIC_CTRL_JACKDETEN) |
+ hbias << SUN50I_ADDA_JACK_MIC_CTRL_MICADCEN);
break;
default:
break;
--
2.44.0
From: Arnaud Ferraris <[email protected]>
Add support for the jack detection functionality in the A64 variant,
which uses a pair of IRQs; and microphone accessory (button) detection,
which uses an ADC with an IRQ trigger.
IRQs will only be triggered if the JACKDETEN, HMICBIASEN, and MICADCEN
bits are set appropriately in the analog codec component
(sun50i-codec-analog), but there is no direct software dependency
between the two components.
Setup ADC so that it samples with period of 16ms, disable smoothing
and enable MDATA threshold (should be below idle voltage/HMIC_DATA
value). Also enable HMIC_N, which makes sure we get HMIC_N samples
after HMIC_DATA crosses the threshold.
This allows us to perform steady state detection of HMIC_DATA, by
comparing current and previous ADC samples, to detect end of the
transient when the user de-presses the button. Otherwise ADC could
sample anywhere within the transient, and the driver may mis-issue
key-press events for other buttons attached to the resistor ladder.
Signed-off-by: Arnaud Ferraris <[email protected]>
[Samuel: Decouple from analog codec, fixes]
Co-developed-by: Samuel Holland <[email protected]>
Signed-off-by: Samuel Holland <[email protected]>
[Ondrej: Almost complete rewrite of the patch, change to use set_jack
API. Better de-bounce, fix mic button handling, better interrupt
processing.]
Co-developed-by: Ondrej Jirman <[email protected]>
Signed-off-by: Ondrej Jirman <[email protected]>
---
sound/soc/sunxi/sun50i-codec-analog.c | 12 +
sound/soc/sunxi/sun8i-codec.c | 305 ++++++++++++++++++++++++++
2 files changed, 317 insertions(+)
diff --git a/sound/soc/sunxi/sun50i-codec-analog.c b/sound/soc/sunxi/sun50i-codec-analog.c
index 2081721a8ff2..2dcdf113b66e 100644
--- a/sound/soc/sunxi/sun50i-codec-analog.c
+++ b/sound/soc/sunxi/sun50i-codec-analog.c
@@ -115,6 +115,11 @@
#define SUN50I_ADDA_HS_MBIAS_CTRL 0x0e
#define SUN50I_ADDA_HS_MBIAS_CTRL_MMICBIASEN 7
+#define SUN50I_ADDA_MDET_CTRL 0x1c
+#define SUN50I_ADDA_MDET_CTRL_SELDETADC_FS 4
+#define SUN50I_ADDA_MDET_CTRL_SELDETADC_DB 2
+#define SUN50I_ADDA_MDET_CTRL_SELDETADC_BF 0
+
#define SUN50I_ADDA_JACK_MIC_CTRL 0x1d
#define SUN50I_ADDA_JACK_MIC_CTRL_JACKDETEN 7
#define SUN50I_ADDA_JACK_MIC_CTRL_INNERRESEN 6
@@ -564,6 +569,13 @@ static int sun50i_codec_analog_probe(struct platform_device *pdev)
BIT(SUN50I_ADDA_JACK_MIC_CTRL_INNERRESEN),
enable << SUN50I_ADDA_JACK_MIC_CTRL_INNERRESEN);
+ /* Select sample interval of the ADC sample to 16ms */
+ regmap_update_bits(regmap, SUN50I_ADDA_MDET_CTRL,
+ 0x7 << SUN50I_ADDA_MDET_CTRL_SELDETADC_FS |
+ 0x3 << SUN50I_ADDA_MDET_CTRL_SELDETADC_BF,
+ 0x3 << SUN50I_ADDA_MDET_CTRL_SELDETADC_FS |
+ 0x3 << SUN50I_ADDA_MDET_CTRL_SELDETADC_BF);
+
return devm_snd_soc_register_component(&pdev->dev,
&sun50i_codec_analog_cmpnt_drv,
NULL, 0);
diff --git a/sound/soc/sunxi/sun8i-codec.c b/sound/soc/sunxi/sun8i-codec.c
index 2a46b96b03cc..43795362fed0 100644
--- a/sound/soc/sunxi/sun8i-codec.c
+++ b/sound/soc/sunxi/sun8i-codec.c
@@ -12,12 +12,16 @@
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/clk.h>
+#include <linux/input.h>
#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/mutex.h>
#include <linux/of.h>
#include <linux/pm_runtime.h>
#include <linux/regmap.h>
#include <linux/log2.h>
+#include <sound/jack.h>
#include <sound/pcm_params.h>
#include <sound/soc.h>
#include <sound/soc-dapm.h>
@@ -118,6 +122,23 @@
#define SUN8I_ADC_VOL_CTRL 0x104
#define SUN8I_ADC_VOL_CTRL_ADCL_VOL 8
#define SUN8I_ADC_VOL_CTRL_ADCR_VOL 0
+#define SUN8I_HMIC_CTRL1 0x110
+#define SUN8I_HMIC_CTRL1_HMIC_M 12
+#define SUN8I_HMIC_CTRL1_HMIC_N 8
+#define SUN8I_HMIC_CTRL1_MDATA_THRESHOLD_DB 5
+#define SUN8I_HMIC_CTRL1_JACK_OUT_IRQ_EN 4
+#define SUN8I_HMIC_CTRL1_JACK_IN_IRQ_EN 3
+#define SUN8I_HMIC_CTRL1_HMIC_DATA_IRQ_EN 0
+#define SUN8I_HMIC_CTRL2 0x114
+#define SUN8I_HMIC_CTRL2_HMIC_SAMPLE 14
+#define SUN8I_HMIC_CTRL2_HMIC_MDATA_THRESHOLD 8
+#define SUN8I_HMIC_CTRL2_HMIC_SF 6
+#define SUN8I_HMIC_STS 0x118
+#define SUN8I_HMIC_STS_MDATA_DISCARD 13
+#define SUN8I_HMIC_STS_HMIC_DATA 8
+#define SUN8I_HMIC_STS_JACK_OUT_IRQ_ST 4
+#define SUN8I_HMIC_STS_JACK_IN_IRQ_ST 3
+#define SUN8I_HMIC_STS_HMIC_DATA_IRQ_ST 0
#define SUN8I_DAC_DIG_CTRL 0x120
#define SUN8I_DAC_DIG_CTRL_ENDA 15
#define SUN8I_DAC_VOL_CTRL 0x124
@@ -143,6 +164,17 @@
#define SUN8I_AIF_CLK_CTRL_WORD_SIZ_MASK GENMASK(5, 4)
#define SUN8I_AIF_CLK_CTRL_DATA_FMT_MASK GENMASK(3, 2)
#define SUN8I_AIF3_CLK_CTRL_AIF3_CLK_SRC_MASK GENMASK(1, 0)
+#define SUN8I_HMIC_CTRL1_HMIC_M_MASK GENMASK(15, 12)
+#define SUN8I_HMIC_CTRL1_HMIC_N_MASK GENMASK(11, 8)
+#define SUN8I_HMIC_CTRL1_MDATA_THRESHOLD_DB_MASK GENMASK(6, 5)
+#define SUN8I_HMIC_CTRL2_HMIC_SAMPLE_MASK GENMASK(15, 14)
+#define SUN8I_HMIC_CTRL2_HMIC_SF_MASK GENMASK(7, 6)
+#define SUN8I_HMIC_STS_HMIC_DATA_MASK GENMASK(12, 8)
+
+#define SUN8I_CODEC_BUTTONS (SND_JACK_BTN_0|\
+ SND_JACK_BTN_1|\
+ SND_JACK_BTN_2|\
+ SND_JACK_BTN_3)
#define SUN8I_CODEC_PASSTHROUGH_SAMPLE_RATE 48000
@@ -178,16 +210,32 @@ struct sun8i_codec_aif {
struct sun8i_codec_quirks {
bool bus_clock : 1;
+ bool jack_detection : 1;
bool legacy_widgets : 1;
bool lrck_inversion : 1;
};
+enum {
+ SUN8I_JACK_STATUS_DISCONNECTED,
+ SUN8I_JACK_STATUS_WAITING_HBIAS,
+ SUN8I_JACK_STATUS_CONNECTED,
+};
+
struct sun8i_codec {
+ struct snd_soc_component *component;
struct regmap *regmap;
struct clk *clk_bus;
struct clk *clk_module;
const struct sun8i_codec_quirks *quirks;
struct sun8i_codec_aif aifs[SUN8I_CODEC_NAIFS];
+ struct snd_soc_jack *jack;
+ struct delayed_work jack_work;
+ int jack_irq;
+ int jack_status;
+ int jack_last_sample;
+ ktime_t jack_hbias_ready;
+ struct mutex jack_mutex;
+ int last_hmic_irq;
unsigned int sysclk_rate;
int sysclk_refcnt;
};
@@ -1245,6 +1293,8 @@ static int sun8i_codec_component_probe(struct snd_soc_component *component)
struct sun8i_codec *scodec = snd_soc_component_get_drvdata(component);
int ret;
+ scodec->component = component;
+
/* Add widgets for backward compatibility with old device trees. */
if (scodec->quirks->legacy_widgets) {
ret = snd_soc_dapm_new_controls(dapm, sun8i_codec_legacy_widgets,
@@ -1281,6 +1331,251 @@ static int sun8i_codec_component_probe(struct snd_soc_component *component)
return 0;
}
+static void sun8i_codec_set_hmic_bias(struct sun8i_codec *scodec, bool enable)
+{
+ struct snd_soc_dapm_context *dapm = &scodec->component->card->dapm;
+ int irq_mask = BIT(SUN8I_HMIC_CTRL1_HMIC_DATA_IRQ_EN);
+
+ if (enable)
+ snd_soc_dapm_force_enable_pin(dapm, "HBIAS");
+ else
+ snd_soc_dapm_disable_pin(dapm, "HBIAS");
+
+ snd_soc_dapm_sync(dapm);
+
+ regmap_update_bits(scodec->regmap, SUN8I_HMIC_CTRL1,
+ irq_mask, enable ? irq_mask : 0);
+}
+
+static void sun8i_codec_jack_work(struct work_struct *work)
+{
+ struct sun8i_codec *scodec = container_of(work, struct sun8i_codec,
+ jack_work.work);
+ unsigned int mdata;
+ int type_mask = scodec->jack->jack->type;
+ int type;
+
+ guard(mutex)(&scodec->jack_mutex);
+
+ if (scodec->jack_status == SUN8I_JACK_STATUS_DISCONNECTED) {
+ if (scodec->last_hmic_irq != SUN8I_HMIC_STS_JACK_IN_IRQ_ST)
+ return;
+
+ scodec->jack_last_sample = -1;
+
+ if (type_mask & SND_JACK_MICROPHONE) {
+ /*
+ * If we were in disconnected state, we enable HBIAS and
+ * wait 600ms before reading initial HDATA value.
+ */
+ scodec->jack_hbias_ready = ktime_add_ms(ktime_get(), 600);
+ sun8i_codec_set_hmic_bias(scodec, true);
+ queue_delayed_work(system_power_efficient_wq,
+ &scodec->jack_work,
+ msecs_to_jiffies(610));
+ scodec->jack_status = SUN8I_JACK_STATUS_WAITING_HBIAS;
+ } else {
+ snd_soc_jack_report(scodec->jack, SND_JACK_HEADPHONE,
+ type_mask);
+ scodec->jack_status = SUN8I_JACK_STATUS_CONNECTED;
+ }
+ } else if (scodec->jack_status == SUN8I_JACK_STATUS_WAITING_HBIAS) {
+ /*
+ * If we're waiting for HBIAS to stabilize, and we get plug-out
+ * interrupt and nothing more for > 100ms, just cancel the
+ * initialization.
+ */
+ if (scodec->last_hmic_irq == SUN8I_HMIC_STS_JACK_OUT_IRQ_ST) {
+ scodec->jack_status = SUN8I_JACK_STATUS_DISCONNECTED;
+ sun8i_codec_set_hmic_bias(scodec, false);
+ return;
+ }
+
+ /*
+ * If we're not done waiting for HBIAS to stabilize, wait more.
+ */
+ if (!ktime_after(ktime_get(), scodec->jack_hbias_ready)) {
+ s64 msecs = ktime_ms_delta(scodec->jack_hbias_ready,
+ ktime_get());
+
+ queue_delayed_work(system_power_efficient_wq,
+ &scodec->jack_work,
+ msecs_to_jiffies(msecs + 10));
+ return;
+ }
+
+ /*
+ * Everything is stabilized, determine jack type and report it.
+ */
+ regmap_read(scodec->regmap, SUN8I_HMIC_STS, &mdata);
+ mdata &= SUN8I_HMIC_STS_HMIC_DATA_MASK;
+ mdata >>= SUN8I_HMIC_STS_HMIC_DATA;
+
+ regmap_write(scodec->regmap, SUN8I_HMIC_STS, 0);
+
+ type = mdata < 16 ? SND_JACK_HEADPHONE : SND_JACK_HEADSET;
+ if (type == SND_JACK_HEADPHONE)
+ sun8i_codec_set_hmic_bias(scodec, false);
+
+ snd_soc_jack_report(scodec->jack, type, type_mask);
+ scodec->jack_status = SUN8I_JACK_STATUS_CONNECTED;
+ } else if (scodec->jack_status == SUN8I_JACK_STATUS_CONNECTED) {
+ if (scodec->last_hmic_irq != SUN8I_HMIC_STS_JACK_OUT_IRQ_ST)
+ return;
+
+ scodec->jack_status = SUN8I_JACK_STATUS_DISCONNECTED;
+ if (type_mask & SND_JACK_MICROPHONE)
+ sun8i_codec_set_hmic_bias(scodec, false);
+
+ snd_soc_jack_report(scodec->jack, 0, type_mask);
+ }
+}
+
+static irqreturn_t sun8i_codec_jack_irq(int irq, void *dev_id)
+{
+ struct sun8i_codec *scodec = dev_id;
+ int type = SND_JACK_HEADSET;
+ unsigned int status, value;
+
+ guard(mutex)(&scodec->jack_mutex);
+
+ regmap_read(scodec->regmap, SUN8I_HMIC_STS, &status);
+ regmap_write(scodec->regmap, SUN8I_HMIC_STS, status);
+
+ /*
+ * De-bounce in/out interrupts via a delayed work re-scheduling to
+ * 100ms after each interrupt..
+ */
+ if (status & BIT(SUN8I_HMIC_STS_JACK_OUT_IRQ_ST)) {
+ /*
+ * Out interrupt has priority over in interrupt so that if
+ * we get both, we assume the disconnected state, which is
+ * safer.
+ */
+ scodec->last_hmic_irq = SUN8I_HMIC_STS_JACK_OUT_IRQ_ST;
+ mod_delayed_work(system_power_efficient_wq, &scodec->jack_work,
+ msecs_to_jiffies(100));
+ } else if (status & BIT(SUN8I_HMIC_STS_JACK_IN_IRQ_ST)) {
+ scodec->last_hmic_irq = SUN8I_HMIC_STS_JACK_IN_IRQ_ST;
+ mod_delayed_work(system_power_efficient_wq, &scodec->jack_work,
+ msecs_to_jiffies(100));
+ } else if (status & BIT(SUN8I_HMIC_STS_HMIC_DATA_IRQ_ST)) {
+ /*
+ * Ignore data interrupts until jack status turns to connected
+ * state, which is after HMIC enable stabilization is completed.
+ * Until then tha data are bogus.
+ */
+ if (scodec->jack_status != SUN8I_JACK_STATUS_CONNECTED)
+ return IRQ_HANDLED;
+
+ value = (status & SUN8I_HMIC_STS_HMIC_DATA_MASK) >>
+ SUN8I_HMIC_STS_HMIC_DATA;
+
+ /*
+ * Assumes 60 mV per ADC LSB increment, 2V bias voltage, 2.2kOhm
+ * bias resistor.
+ */
+ if (value == 0)
+ type |= SND_JACK_BTN_0;
+ else if (value == 1)
+ type |= SND_JACK_BTN_3;
+ else if (value <= 3)
+ type |= SND_JACK_BTN_1;
+ else if (value <= 8)
+ type |= SND_JACK_BTN_2;
+
+ /*
+ * De-bounce. Only report button after two consecutive A/D
+ * samples are identical.
+ */
+ if (scodec->jack_last_sample >= 0 &&
+ scodec->jack_last_sample == value)
+ snd_soc_jack_report(scodec->jack, type,
+ scodec->jack->jack->type);
+
+ scodec->jack_last_sample = value;
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int sun8i_codec_enable_jack_detect(struct snd_soc_component *component,
+ struct snd_soc_jack *jack, void *data)
+{
+ struct sun8i_codec *scodec = snd_soc_component_get_drvdata(component);
+ struct platform_device *pdev = to_platform_device(component->dev);
+ int ret;
+
+ if (!scodec->quirks->jack_detection)
+ return 0;
+
+ scodec->jack = jack;
+
+ scodec->jack_irq = platform_get_irq(pdev, 0);
+ if (scodec->jack_irq < 0)
+ return scodec->jack_irq;
+
+ /* Reserved value required for jack IRQs to trigger. */
+ regmap_write(scodec->regmap, SUN8I_HMIC_CTRL1,
+ 0xf << SUN8I_HMIC_CTRL1_HMIC_N |
+ 0x0 << SUN8I_HMIC_CTRL1_MDATA_THRESHOLD_DB |
+ 0x4 << SUN8I_HMIC_CTRL1_HMIC_M);
+
+ /* Sample the ADC at 128 Hz; bypass smooth filter. */
+ regmap_write(scodec->regmap, SUN8I_HMIC_CTRL2,
+ 0x0 << SUN8I_HMIC_CTRL2_HMIC_SAMPLE |
+ 0x17 << SUN8I_HMIC_CTRL2_HMIC_MDATA_THRESHOLD |
+ 0x0 << SUN8I_HMIC_CTRL2_HMIC_SF);
+
+ /* Do not discard any MDATA, enable user written MDATA threshold. */
+ regmap_write(scodec->regmap, SUN8I_HMIC_STS, 0);
+
+ regmap_set_bits(scodec->regmap, SUN8I_HMIC_CTRL1,
+ BIT(SUN8I_HMIC_CTRL1_JACK_OUT_IRQ_EN) |
+ BIT(SUN8I_HMIC_CTRL1_JACK_IN_IRQ_EN));
+
+ ret = devm_request_threaded_irq(&pdev->dev, scodec->jack_irq,
+ NULL, sun8i_codec_jack_irq,
+ IRQF_ONESHOT,
+ dev_name(&pdev->dev), scodec);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static void sun8i_codec_disable_jack_detect(struct snd_soc_component *component)
+{
+ struct sun8i_codec *scodec = snd_soc_component_get_drvdata(component);
+
+ if (!scodec->quirks->jack_detection)
+ return;
+
+ devm_free_irq(component->dev, scodec->jack_irq, scodec);
+
+ cancel_delayed_work_sync(&scodec->jack_work);
+
+ regmap_clear_bits(scodec->regmap, SUN8I_HMIC_CTRL1,
+ BIT(SUN8I_HMIC_CTRL1_JACK_OUT_IRQ_EN) |
+ BIT(SUN8I_HMIC_CTRL1_JACK_IN_IRQ_EN) |
+ BIT(SUN8I_HMIC_CTRL1_HMIC_DATA_IRQ_EN));
+
+ scodec->jack = NULL;
+}
+
+static int sun8i_codec_component_set_jack(struct snd_soc_component *component,
+ struct snd_soc_jack *jack, void *data)
+{
+ int ret = 0;
+
+ if (jack)
+ ret = sun8i_codec_enable_jack_detect(component, jack, data);
+ else
+ sun8i_codec_disable_jack_detect(component);
+
+ return ret;
+}
+
static const struct snd_soc_component_driver sun8i_soc_component = {
.controls = sun8i_codec_controls,
.num_controls = ARRAY_SIZE(sun8i_codec_controls),
@@ -1288,16 +1583,23 @@ static const struct snd_soc_component_driver sun8i_soc_component = {
.num_dapm_widgets = ARRAY_SIZE(sun8i_codec_dapm_widgets),
.dapm_routes = sun8i_codec_dapm_routes,
.num_dapm_routes = ARRAY_SIZE(sun8i_codec_dapm_routes),
+ .set_jack = sun8i_codec_component_set_jack,
.probe = sun8i_codec_component_probe,
.idle_bias_on = 1,
.suspend_bias_off = 1,
.endianness = 1,
};
+static bool sun8i_codec_volatile_reg(struct device *dev, unsigned int reg)
+{
+ return reg == SUN8I_HMIC_STS;
+}
+
static const struct regmap_config sun8i_codec_regmap_config = {
.reg_bits = 32,
.reg_stride = 4,
.val_bits = 32,
+ .volatile_reg = sun8i_codec_volatile_reg,
.max_register = SUN8I_DAC_MXR_SRC,
.cache_type = REGCACHE_FLAT,
@@ -1314,6 +1616,8 @@ static int sun8i_codec_probe(struct platform_device *pdev)
return -ENOMEM;
scodec->quirks = of_device_get_match_data(&pdev->dev);
+ INIT_DELAYED_WORK(&scodec->jack_work, sun8i_codec_jack_work);
+ mutex_init(&scodec->jack_mutex);
platform_set_drvdata(pdev, scodec);
@@ -1387,6 +1691,7 @@ static const struct sun8i_codec_quirks sun8i_a33_quirks = {
static const struct sun8i_codec_quirks sun50i_a64_quirks = {
.bus_clock = true,
+ .jack_detection = true,
};
static const struct of_device_id sun8i_codec_of_match[] = {
--
2.44.0
From: Samuel Holland <[email protected]>
For codec variants that have a bus clock, that clock must be running to
receive interrupts. Since jack and mic accessory detection should work
even when no audio is playing, that means the bus clock should be
enabled any time the system is on.
Accomplish that by tying the bus clock to the runtime PM state, which is
then tied to the bias level not being OFF. Since the codec sets
idle_bias_on, bias will generally never be OFF. However, we can set
suspend_bias_off to maintain the power savings of gating the bus clock
during suspend, when we don't expect jack/accessory detection to work.
Signed-off-by: Samuel Holland <[email protected]>
Signed-off-by: Ondřej Jirman <[email protected]>
---
sound/soc/sunxi/sun8i-codec.c | 41 ++++++++++++++++++++++++++++-------
1 file changed, 33 insertions(+), 8 deletions(-)
diff --git a/sound/soc/sunxi/sun8i-codec.c b/sound/soc/sunxi/sun8i-codec.c
index 7b45ddffe990..2a46b96b03cc 100644
--- a/sound/soc/sunxi/sun8i-codec.c
+++ b/sound/soc/sunxi/sun8i-codec.c
@@ -177,12 +177,14 @@ struct sun8i_codec_aif {
};
struct sun8i_codec_quirks {
- bool legacy_widgets : 1;
- bool lrck_inversion : 1;
+ bool bus_clock : 1;
+ bool legacy_widgets : 1;
+ bool lrck_inversion : 1;
};
struct sun8i_codec {
struct regmap *regmap;
+ struct clk *clk_bus;
struct clk *clk_module;
const struct sun8i_codec_quirks *quirks;
struct sun8i_codec_aif aifs[SUN8I_CODEC_NAIFS];
@@ -197,6 +199,14 @@ static int sun8i_codec_runtime_resume(struct device *dev)
struct sun8i_codec *scodec = dev_get_drvdata(dev);
int ret;
+ if (scodec->clk_bus) {
+ ret = clk_prepare_enable(scodec->clk_bus);
+ if (ret) {
+ dev_err(dev, "Failed to enable the bus clock\n");
+ return ret;
+ }
+ }
+
regcache_cache_only(scodec->regmap, false);
ret = regcache_sync(scodec->regmap);
@@ -215,6 +225,9 @@ static int sun8i_codec_runtime_suspend(struct device *dev)
regcache_cache_only(scodec->regmap, true);
regcache_mark_dirty(scodec->regmap);
+ if (scodec->clk_bus)
+ clk_disable_unprepare(scodec->clk_bus);
+
return 0;
}
@@ -1277,6 +1290,7 @@ static const struct snd_soc_component_driver sun8i_soc_component = {
.num_dapm_routes = ARRAY_SIZE(sun8i_codec_dapm_routes),
.probe = sun8i_codec_component_probe,
.idle_bias_on = 1,
+ .suspend_bias_off = 1,
.endianness = 1,
};
@@ -1299,6 +1313,18 @@ static int sun8i_codec_probe(struct platform_device *pdev)
if (!scodec)
return -ENOMEM;
+ scodec->quirks = of_device_get_match_data(&pdev->dev);
+
+ platform_set_drvdata(pdev, scodec);
+
+ if (scodec->quirks->bus_clock) {
+ scodec->clk_bus = devm_clk_get(&pdev->dev, "bus");
+ if (IS_ERR(scodec->clk_bus)) {
+ dev_err(&pdev->dev, "Failed to get the bus clock\n");
+ return PTR_ERR(scodec->clk_bus);
+ }
+ }
+
scodec->clk_module = devm_clk_get(&pdev->dev, "mod");
if (IS_ERR(scodec->clk_module)) {
dev_err(&pdev->dev, "Failed to get the module clock\n");
@@ -1311,17 +1337,14 @@ static int sun8i_codec_probe(struct platform_device *pdev)
return PTR_ERR(base);
}
- scodec->regmap = devm_regmap_init_mmio_clk(&pdev->dev, "bus", base,
- &sun8i_codec_regmap_config);
+ scodec->regmap = devm_regmap_init_mmio(&pdev->dev, base,
+ &sun8i_codec_regmap_config);
if (IS_ERR(scodec->regmap)) {
dev_err(&pdev->dev, "Failed to create our regmap\n");
return PTR_ERR(scodec->regmap);
}
- scodec->quirks = of_device_get_match_data(&pdev->dev);
-
- platform_set_drvdata(pdev, scodec);
-
+ regcache_cache_only(scodec->regmap, true);
pm_runtime_enable(&pdev->dev);
if (!pm_runtime_enabled(&pdev->dev)) {
ret = sun8i_codec_runtime_resume(&pdev->dev);
@@ -1357,11 +1380,13 @@ static void sun8i_codec_remove(struct platform_device *pdev)
}
static const struct sun8i_codec_quirks sun8i_a33_quirks = {
+ .bus_clock = true,
.legacy_widgets = true,
.lrck_inversion = true,
};
static const struct sun8i_codec_quirks sun50i_a64_quirks = {
+ .bus_clock = true,
};
static const struct of_device_id sun8i_codec_of_match[] = {
--
2.44.0
From: Samuel Holland <[email protected]>
With idle_bias_on and suspend_bias_off, there are bias level transitions
that match the suspend/resume callbacks. However, there are also
transitions during probe (OFF => STANDBY) and removal (STANDBY => OFF).
By using the set_bias_level hook, the driver can have one copy of code
that would otherwise be duplicated between the probe/resume and
suspend/remove hooks.
Signed-off-by: Samuel Holland <[email protected]>
Signed-off-by: Ondřej Jirman <[email protected]>
---
sound/soc/sunxi/sun50i-codec-analog.c | 29 +++++++++++++++++----------
1 file changed, 18 insertions(+), 11 deletions(-)
diff --git a/sound/soc/sunxi/sun50i-codec-analog.c b/sound/soc/sunxi/sun50i-codec-analog.c
index 8a32d05e23e1..cedd4de42d1a 100644
--- a/sound/soc/sunxi/sun50i-codec-analog.c
+++ b/sound/soc/sunxi/sun50i-codec-analog.c
@@ -471,17 +471,23 @@ static const struct snd_soc_dapm_route sun50i_a64_codec_routes[] = {
{ "EARPIECE", NULL, "Earpiece Amp" },
};
-static int sun50i_a64_codec_suspend(struct snd_soc_component *component)
+static int sun50i_a64_codec_set_bias_level(struct snd_soc_component *component,
+ enum snd_soc_bias_level level)
{
- return regmap_update_bits(component->regmap, SUN50I_ADDA_HP_CTRL,
- BIT(SUN50I_ADDA_HP_CTRL_PA_CLK_GATE),
- BIT(SUN50I_ADDA_HP_CTRL_PA_CLK_GATE));
-}
+ switch (level) {
+ case SND_SOC_BIAS_OFF:
+ regmap_set_bits(component->regmap, SUN50I_ADDA_HP_CTRL,
+ BIT(SUN50I_ADDA_HP_CTRL_PA_CLK_GATE));
+ break;
+ case SND_SOC_BIAS_STANDBY:
+ regmap_clear_bits(component->regmap, SUN50I_ADDA_HP_CTRL,
+ BIT(SUN50I_ADDA_HP_CTRL_PA_CLK_GATE));
+ break;
+ default:
+ break;
+ }
-static int sun50i_a64_codec_resume(struct snd_soc_component *component)
-{
- return regmap_update_bits(component->regmap, SUN50I_ADDA_HP_CTRL,
- BIT(SUN50I_ADDA_HP_CTRL_PA_CLK_GATE), 0);
+ return 0;
}
static const struct snd_soc_component_driver sun50i_codec_analog_cmpnt_drv = {
@@ -491,8 +497,9 @@ static const struct snd_soc_component_driver sun50i_codec_analog_cmpnt_drv = {
.num_dapm_widgets = ARRAY_SIZE(sun50i_a64_codec_widgets),
.dapm_routes = sun50i_a64_codec_routes,
.num_dapm_routes = ARRAY_SIZE(sun50i_a64_codec_routes),
- .suspend = sun50i_a64_codec_suspend,
- .resume = sun50i_a64_codec_resume,
+ .set_bias_level = sun50i_a64_codec_set_bias_level,
+ .idle_bias_on = true,
+ .suspend_bias_off = true,
};
static const struct of_device_id sun50i_codec_analog_of_match[] = {
--
2.44.0
On Sat, 02 Mar 2024 15:00:34 +0100, Ondřej Jirman wrote:
> This series adds support for jack detection to this codec. I used
> and tested this on Pinephone. It works quite nicely. I tested it
> against Android headset mic button resistor specification.
>
> The patches are a rewritten and debugged version of the original
> ones from Arnaud Ferraris and Samuel Holland, improved to better
> handle headset button presses and with more robust plug-in/out
> event debouncing, and to use set_jack API instead of sniffing
> the sound card widget names, to detect the type of jack connector.
>
> [...]
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next
Thanks!
[1/4] ASoC: sun50i-codec-analog: Move suspend/resume to set_bias_level
commit: c0454d31e05062b1c7df7eef21855ba1f56c5158
[2/4] ASoC: sun8i-codec: Enable bus clock at STANDBY and higher bias
commit: c556814b926c3f16fdca3d18cac793ccf0d14c44
[3/4] ASoC: sun50i-codec-analog: Enable jack detection on startup
commit: d5961e43b28668088087befbf4f7a043bd0ae65c
[4/4] ASoC: sun8i-codec: Implement jack and accessory detection
commit: 21fa98f4197bb3365dda1417708b318f403c13c1
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
Hello Mark,
On Tue, Mar 26, 2024 at 03:27:41PM +0000, Mark Brown wrote:
> On Sat, 02 Mar 2024 15:00:34 +0100, Ondřej Jirman wrote:
> > This series adds support for jack detection to this codec. I used
> > and tested this on Pinephone. It works quite nicely. I tested it
> > against Android headset mic button resistor specification.
> >
> > The patches are a rewritten and debugged version of the original
> > ones from Arnaud Ferraris and Samuel Holland, improved to better
> > handle headset button presses and with more robust plug-in/out
> > event debouncing, and to use set_jack API instead of sniffing
> > the sound card widget names, to detect the type of jack connector.
> >
> > [...]
>
> Applied to
>
> https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next
Thank you.
Coincidentally, Intel kernel test bot found an issue today that this fails to
build with CONFIG_SND_JACK_INPUT_DEV disabled. Should I send a followup fix or
should I send v5 with the fix integrated into the patch that breaks?
Kind regards,
o.
> Thanks!
>
> [1/4] ASoC: sun50i-codec-analog: Move suspend/resume to set_bias_level
> commit: c0454d31e05062b1c7df7eef21855ba1f56c5158
> [2/4] ASoC: sun8i-codec: Enable bus clock at STANDBY and higher bias
> commit: c556814b926c3f16fdca3d18cac793ccf0d14c44
> [3/4] ASoC: sun50i-codec-analog: Enable jack detection on startup
> commit: d5961e43b28668088087befbf4f7a043bd0ae65c
> [4/4] ASoC: sun8i-codec: Implement jack and accessory detection
> commit: 21fa98f4197bb3365dda1417708b318f403c13c1
>
> All being well this means that it will be integrated into the linux-next
> tree (usually sometime in the next 24 hours) and sent to Linus during
> the next merge window (or sooner if it is a bug fix), however if
> problems are discovered then the patch may be dropped or reverted.
>
> You may get further e-mails resulting from automated or manual testing
> and review of the tree, please engage with people reporting problems and
> send followup patches addressing any issues that are reported if needed.
>
> If any updates are required or you are submitting further changes they
> should be sent as incremental updates against current git, existing
> patches will not be replaced.
>
> Please add any relevant lists and maintainers to the CCs when replying
> to this mail.
>
> Thanks,
> Mark
>
On Tue, Mar 26, 2024 at 05:33:14PM +0100, Ondřej Jirman wrote:
> Coincidentally, Intel kernel test bot found an issue today that this fails to
> build with CONFIG_SND_JACK_INPUT_DEV disabled. Should I send a followup fix or
> should I send v5 with the fix integrated into the patch that breaks?
Please send a followup.