2023-11-17 09:02:57

by Xingui Yang

[permalink] [raw]
Subject: [PATCH v4] scsi: libsas: Fix the failure of adding phy with zero-address to port

When connecting to the epander device, first disable and then enable the
local phy. The following BUG() will be triggered with a small probability:

[562240.051046] sas: phy19 part of wide port with phy16
[562240.051197] sas: ex 500e004aaaaaaa1f phy19:U:0 attached: 0000000000000000 (no device)
[562240.051203] sas: done REVALIDATING DOMAIN on port 0, pid:435909, res 0x0
<...>
[562240.062536] sas: ex 500e004aaaaaaa1f phy0 new device attached
[562240.062616] sas: ex 500e004aaaaaaa1f phy00:U:5 attached: 0000000000000000 (stp)
[562240.062680] port-7:7:0: trying to add phy phy-7:7:19 fails: it's already part of another port
[562240.085064] ------------[ cut here ]------------
[562240.096612] kernel BUG at drivers/scsi/scsi_transport_sas.c:1083!
[562240.109611] Internal error: Oops - BUG: 0 [#1] SMP
[562240.343518] Process kworker/u256:3 (pid: 435909, stack limit = 0x0000000003bcbebf)
[562240.421714] Workqueue: 0000:b4:02.0_disco_q sas_revalidate_domain [libsas]
[562240.437173] pstate: 40c00009 (nZcv daif +PAN +UAO)
[562240.450478] pc : sas_port_add_phy+0x13c/0x168 [scsi_transport_sas]
[562240.465283] lr : sas_port_add_phy+0x13c/0x168 [scsi_transport_sas]
[562240.479751] sp : ffff0000300cfa70
[562240.674822] Call trace:
[562240.682709] sas_port_add_phy+0x13c/0x168 [scsi_transport_sas]
[562240.694013] sas_ex_get_linkrate.isra.5+0xcc/0x128 [libsas]
[562240.704957] sas_ex_discover_end_dev+0xfc/0x538 [libsas]
[562240.715508] sas_ex_discover_dev+0x3cc/0x4b8 [libsas]
[562240.725634] sas_ex_discover_devices+0x9c/0x1a8 [libsas]
[562240.735855] sas_ex_revalidate_domain+0x2f0/0x450 [libsas]
[562240.746123] sas_revalidate_domain+0x158/0x160 [libsas]
[562240.756014] process_one_work+0x1b4/0x448
[562240.764548] worker_thread+0x54/0x468
[562240.772562] kthread+0x134/0x138
[562240.779989] ret_from_fork+0x10/0x18

What causes this problem:
1. When phy19 was initially added to the parent port, ex_phy->port was not
set. As a result, when phy19 was removed from the parent wide port, it was
not deleted from the phy_list of the parent port.

2. The rate of the newly connected SATA device to phy0 is less than 1.5G,
and its sas_address was set to 0. After creating port 7:7:0, it attempts to
add the expander's other zero-addressed phy to this port.

3. When adding phy19 to port-7:7:0, it is prompted that phy19 already
belongs to another port, which triggers the current problem.

Fix the problem as follows:
1. When ex_phy is added to the parent port, set ex_phy->port to
ex_dev->parent_port.

2. Set ex_dev->parent_port to NULL when the parent port's PHY count is 0.

3. When phy->attached_dev_type != NO_DEVICE, do not set the zero address
for phy->attached_sas_addr.

Fixes: 2908d778ab3e ("[SCSI] aic94xx: new driver")
Fixes: 7d1d86518118 ("[SCSI] libsas: fix false positive 'device attached' conditions")
Signed-off-by: Xingui Yang <[email protected]>
---
v3 -> v4:
1. Update patch title and comments based on John's suggestion.

v2 -> v3:
1. Set ex_dev->parent_port to NULL when the number of PHYs of the parent
port becomes 0
2. Update the comments

v1 -> v2:
1. Set ex_phy->port with parent_port when ex_phy is added to the parent port
2. Set ex_phy to NULL when free expander
3. Update the comments
---
drivers/scsi/libsas/sas_discover.c | 4 +++-
drivers/scsi/libsas/sas_expander.c | 8 +++++---
drivers/scsi/libsas/sas_internal.h | 1 +
3 files changed, 9 insertions(+), 4 deletions(-)

diff --git a/drivers/scsi/libsas/sas_discover.c b/drivers/scsi/libsas/sas_discover.c
index 8fb7c41c0962..8eb3888a9e57 100644
--- a/drivers/scsi/libsas/sas_discover.c
+++ b/drivers/scsi/libsas/sas_discover.c
@@ -296,8 +296,10 @@ void sas_free_device(struct kref *kref)
dev->phy = NULL;

/* remove the phys and ports, everything else should be gone */
- if (dev_is_expander(dev->dev_type))
+ if (dev_is_expander(dev->dev_type)) {
kfree(dev->ex_dev.ex_phy);
+ dev->ex_dev.ex_phy = NULL;
+ }

if (dev_is_sata(dev) && dev->sata_dev.ap) {
ata_sas_tport_delete(dev->sata_dev.ap);
diff --git a/drivers/scsi/libsas/sas_expander.c b/drivers/scsi/libsas/sas_expander.c
index a2204674b680..89d44a9dc4e3 100644
--- a/drivers/scsi/libsas/sas_expander.c
+++ b/drivers/scsi/libsas/sas_expander.c
@@ -239,8 +239,7 @@ static void sas_set_ex_phy(struct domain_device *dev, int phy_id,
/* help some expanders that fail to zero sas_address in the 'no
* device' case
*/
- if (phy->attached_dev_type == SAS_PHY_UNUSED ||
- phy->linkrate < SAS_LINK_RATE_1_5_GBPS)
+ if (phy->attached_dev_type == SAS_PHY_UNUSED)
memset(phy->attached_sas_addr, 0, SAS_ADDR_SIZE);
else
memcpy(phy->attached_sas_addr, dr->attached_sas_addr, SAS_ADDR_SIZE);
@@ -1844,9 +1843,12 @@ static void sas_unregister_devs_sas_addr(struct domain_device *parent,
if (phy->port) {
sas_port_delete_phy(phy->port, phy->phy);
sas_device_set_phy(found, phy->port);
- if (phy->port->num_phys == 0)
+ if (phy->port->num_phys == 0) {
list_add_tail(&phy->port->del_list,
&parent->port->sas_port_del_list);
+ if (ex_dev->parent_port == phy->port)
+ ex_dev->parent_port = NULL;
+ }
phy->port = NULL;
}
}
diff --git a/drivers/scsi/libsas/sas_internal.h b/drivers/scsi/libsas/sas_internal.h
index 3804aef165ad..e860d5b19880 100644
--- a/drivers/scsi/libsas/sas_internal.h
+++ b/drivers/scsi/libsas/sas_internal.h
@@ -202,6 +202,7 @@ static inline void sas_add_parent_port(struct domain_device *dev, int phy_id)
sas_port_mark_backlink(ex->parent_port);
}
sas_port_add_phy(ex->parent_port, ex_phy->phy);
+ ex_phy->port = ex->parent_port;
}

static inline struct domain_device *sas_alloc_device(void)
--
2.17.1


2023-11-23 14:53:33

by John Garry

[permalink] [raw]
Subject: Re: [PATCH v4] scsi: libsas: Fix the failure of adding phy with zero-address to port

On 17/11/2023 09:00, Xingui Yang wrote:

Sorry for being slow to come back to this. However I still have questions...

> When connecting to the epander device, first disable and then enable the

/s/epander/expander/

And connecting what to the expander? Is it a SATA disk?

Or the SATA disk is already attached to the expander and we are now
attaching the expander to the host?

It is hard to follow this.

> local phy.

So is the local phy disabled initially? Or is was it initially enabled
and we disable+re-enable just when attaching, so that there is a race?

> The following BUG() will be triggered with a small probability:
>
> [562240.051046] sas: phy19 part of wide port with phy16

Where is this print in the code? I see "part of a wide port with
phy%02d" in sas_discover_dev()

> [562240.051197] sas: ex 500e004aaaaaaa1f phy19:U:0 attached: 0000000000000000 (no device)
> [562240.051203] sas: done REVALIDATING DOMAIN on port 0, pid:435909, res 0x0
> <...>
> [562240.062536] sas: ex 500e004aaaaaaa1f phy0 new device attached
> [562240.062616] sas: ex 500e004aaaaaaa1f phy00:U:5 attached: 0000000000000000 (stp)
> [562240.062680] port-7:7:0: trying to add phy phy-7:7:19 fails: it's already part of another port
> [562240.085064] ------------[ cut here ]------------
> [562240.096612] kernel BUG at drivers/scsi/scsi_transport_sas.c:1083!
> [562240.109611] Internal error: Oops - BUG: 0 [#1] SMP
> [562240.343518] Process kworker/u256:3 (pid: 435909, stack limit = 0x0000000003bcbebf)
> [562240.421714] Workqueue: 0000:b4:02.0_disco_q sas_revalidate_domain [libsas]
> [562240.437173] pstate: 40c00009 (nZcv daif +PAN +UAO)
> [562240.450478] pc : sas_port_add_phy+0x13c/0x168 [scsi_transport_sas]
> [562240.465283] lr : sas_port_add_phy+0x13c/0x168 [scsi_transport_sas]
> [562240.479751] sp : ffff0000300cfa70
> [562240.674822] Call trace:
> [562240.682709] sas_port_add_phy+0x13c/0x168 [scsi_transport_sas]
> [562240.694013] sas_ex_get_linkrate.isra.5+0xcc/0x128 [libsas]
> [562240.704957] sas_ex_discover_end_dev+0xfc/0x538 [libsas]
> [562240.715508] sas_ex_discover_dev+0x3cc/0x4b8 [libsas]
> [562240.725634] sas_ex_discover_devices+0x9c/0x1a8 [libsas]
> [562240.735855] sas_ex_revalidate_domain+0x2f0/0x450 [libsas]
> [562240.746123] sas_revalidate_domain+0x158/0x160 [libsas]
> [562240.756014] process_one_work+0x1b4/0x448
> [562240.764548] worker_thread+0x54/0x468
> [562240.772562] kthread+0x134/0x138
> [562240.779989] ret_from_fork+0x10/0x18
>
> What causes this problem:
> 1. When phy19 was initially added to the parent port, ex_phy->port was not

phy19 is the expander phy attached to the host, right?

> set. As a result, when phy19 was removed from the parent wide port,

You seem to be getting ahead of yourself. It has not been mentioned when
phy19 is removed from the parent wide port.

> it was
> not deleted from the phy_list of the parent port.
>
> 2. The rate of the newly connected SATA device to phy0 is less than 1.5G,
> and its sas_address was set to 0. After creating port 7:7:0

is 7:7:0 the port which the SATA device is part of?

> , it attempts to
> add the expander's other zero-addressed phy to this port.
>
> 3. When adding phy19 to port-7:7:0

Which would be the incorrect thing to do, right? I am basing that on my
assumption that 7:7:0 is the port which the SATA device is part of.

>, it is prompted that phy19 already
> belongs to another port, which triggers the current problem.
>
> Fix the problem as follows:
> 1. When ex_phy is added to the parent port, set ex_phy->port to
> ex_dev->parent_port.
>
> 2. Set ex_dev->parent_port to NULL when the parent port's PHY count is 0.
>
> 3. When phy->attached_dev_type != NO_DEVICE, do not set the zero address
> for phy->attached_sas_addr.
>
> Fixes: 2908d778ab3e ("[SCSI] aic94xx: new driver")
> Fixes: 7d1d86518118 ("[SCSI] libsas: fix false positive 'device attached' conditions")
> Signed-off-by: Xingui Yang <[email protected]>
> ---
> v3 -> v4:
> 1. Update patch title and comments based on John's suggestion.
>
> v2 -> v3:
> 1. Set ex_dev->parent_port to NULL when the number of PHYs of the parent
> port becomes 0
> 2. Update the comments
>
> v1 -> v2:
> 1. Set ex_phy->port with parent_port when ex_phy is added to the parent port
> 2. Set ex_phy to NULL when free expander
> 3. Update the comments
> ---
> drivers/scsi/libsas/sas_discover.c | 4 +++-
> drivers/scsi/libsas/sas_expander.c | 8 +++++---
> drivers/scsi/libsas/sas_internal.h | 1 +
> 3 files changed, 9 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/scsi/libsas/sas_discover.c b/drivers/scsi/libsas/sas_discover.c
> index 8fb7c41c0962..8eb3888a9e57 100644
> --- a/drivers/scsi/libsas/sas_discover.c
> +++ b/drivers/scsi/libsas/sas_discover.c
> @@ -296,8 +296,10 @@ void sas_free_device(struct kref *kref)
> dev->phy = NULL;
>
> /* remove the phys and ports, everything else should be gone */
> - if (dev_is_expander(dev->dev_type))
> + if (dev_is_expander(dev->dev_type)) {
> kfree(dev->ex_dev.ex_phy);
> + dev->ex_dev.ex_phy = NULL;

This is strange, as we free the dev later. Where can dev->ex_dev.ex_phy
be checked before dev is freed?

> + }
>
> if (dev_is_sata(dev) && dev->sata_dev.ap) {
> ata_sas_tport_delete(dev->sata_dev.ap);
> diff --git a/drivers/scsi/libsas/sas_expander.c b/drivers/scsi/libsas/sas_expander.c
> index a2204674b680..89d44a9dc4e3 100644
> --- a/drivers/scsi/libsas/sas_expander.c
> +++ b/drivers/scsi/libsas/sas_expander.c
> @@ -239,8 +239,7 @@ static void sas_set_ex_phy(struct domain_device *dev, int phy_id,
> /* help some expanders that fail to zero sas_address in the 'no
> * device' case
> */
> - if (phy->attached_dev_type == SAS_PHY_UNUSED ||
> - phy->linkrate < SAS_LINK_RATE_1_5_GBPS)
> + if (phy->attached_dev_type == SAS_PHY_UNUSED)
> memset(phy->attached_sas_addr, 0, SAS_ADDR_SIZE);
> else
> memcpy(phy->attached_sas_addr, dr->attached_sas_addr, SAS_ADDR_SIZE);
> @@ -1844,9 +1843,12 @@ static void sas_unregister_devs_sas_addr(struct domain_device *parent,
> if (phy->port) {
> sas_port_delete_phy(phy->port, phy->phy);
> sas_device_set_phy(found, phy->port);
> - if (phy->port->num_phys == 0)
> + if (phy->port->num_phys == 0) {
> list_add_tail(&phy->port->del_list,
> &parent->port->sas_port_del_list);
> + if (ex_dev->parent_port == phy->port)
> + ex_dev->parent_port = NULL;
> + }
> phy->port = NULL;
> }
> }
> diff --git a/drivers/scsi/libsas/sas_internal.h b/drivers/scsi/libsas/sas_internal.h
> index 3804aef165ad..e860d5b19880 100644
> --- a/drivers/scsi/libsas/sas_internal.h
> +++ b/drivers/scsi/libsas/sas_internal.h
> @@ -202,6 +202,7 @@ static inline void sas_add_parent_port(struct domain_device *dev, int phy_id)
> sas_port_mark_backlink(ex->parent_port);
> }
> sas_port_add_phy(ex->parent_port, ex_phy->phy);
> + ex_phy->port = ex->parent_port;

We already do this in sas_ex_join_wide_port(), right?

I am not saying that what we do now does not have a problem - I am just
trying to understand what currently happens

Thanks,
John

> }
>
> static inline struct domain_device *sas_alloc_device(void)

2023-11-24 02:28:22

by Xingui Yang

[permalink] [raw]
Subject: Re: [PATCH v4] scsi: libsas: Fix the failure of adding phy with zero-address to port

Hi John,

On 2023/11/23 22:52, John Garry wrote:
> On 17/11/2023 09:00, Xingui Yang wrote:
>
> Sorry for being slow to come back to this. However I still have
> questions...
>
>> When connecting to the epander device, first disable and then enable the
>
> /s/epander/expander/
>
> And connecting what to the expander? Is it a SATA disk?
>
> Or the SATA disk is already attached to the expander and we are now
> attaching the expander to the host?
>
> It is hard to follow this.
>
>> local phy.
>
> So is the local phy disabled initially? Or is was it initially enabled
> and we disable+re-enable just when attaching, so that there is a race?
>
>> The following BUG() will be triggered with a small probability:
>>
>> [562240.051046] sas: phy19 part of wide port with phy16
>
> Where is this print in the code? I see "part of a wide port with
> phy%02d" in sas_discover_dev()
>
>> [562240.051197] sas: ex 500e004aaaaaaa1f phy19:U:0 attached:
>> 0000000000000000 (no device)
>> [562240.051203] sas: done REVALIDATING DOMAIN on port 0, pid:435909,
>> res 0x0
>> <...>
>> [562240.062536] sas: ex 500e004aaaaaaa1f phy0 new device attached
>> [562240.062616] sas: ex 500e004aaaaaaa1f phy00:U:5 attached:
>> 0000000000000000 (stp)
>> [562240.062680]  port-7:7:0: trying to add phy phy-7:7:19 fails: it's
>> already part of another port
>> [562240.085064] ------------[ cut here ]------------
>> [562240.096612] kernel BUG at drivers/scsi/scsi_transport_sas.c:1083!
>> [562240.109611] Internal error: Oops - BUG: 0 [#1] SMP
>> [562240.343518] Process kworker/u256:3 (pid: 435909, stack limit =
>> 0x0000000003bcbebf)
>> [562240.421714] Workqueue: 0000:b4:02.0_disco_q sas_revalidate_domain
>> [libsas]
>> [562240.437173] pstate: 40c00009 (nZcv daif +PAN +UAO)
>> [562240.450478] pc : sas_port_add_phy+0x13c/0x168 [scsi_transport_sas]
>> [562240.465283] lr : sas_port_add_phy+0x13c/0x168 [scsi_transport_sas]
>> [562240.479751] sp : ffff0000300cfa70
>> [562240.674822] Call trace:
>> [562240.682709]  sas_port_add_phy+0x13c/0x168 [scsi_transport_sas]
>> [562240.694013]  sas_ex_get_linkrate.isra.5+0xcc/0x128 [libsas]
>> [562240.704957]  sas_ex_discover_end_dev+0xfc/0x538 [libsas]
>> [562240.715508]  sas_ex_discover_dev+0x3cc/0x4b8 [libsas]
>> [562240.725634]  sas_ex_discover_devices+0x9c/0x1a8 [libsas]
>> [562240.735855]  sas_ex_revalidate_domain+0x2f0/0x450 [libsas]
>> [562240.746123]  sas_revalidate_domain+0x158/0x160 [libsas]
>> [562240.756014]  process_one_work+0x1b4/0x448
>> [562240.764548]  worker_thread+0x54/0x468
>> [562240.772562]  kthread+0x134/0x138
>> [562240.779989]  ret_from_fork+0x10/0x18
>>
>> What causes this problem:
>> 1. When phy19 was initially added to the parent port, ex_phy->port was
>> not
>
> phy19 is the expander phy attached to the host, right?
>
>> set. As a result, when phy19 was removed from the parent wide port,
>
> You seem to be getting ahead of yourself. It has not been mentioned when
> phy19 is removed from the parent wide port.
>
>> it was
>> not deleted from the phy_list of the parent port.
>>
>> 2. The rate of the newly connected SATA device to phy0 is less than 1.5G,
>> and its sas_address was set to 0. After creating port 7:7:0
>
> is 7:7:0 the port which the SATA device is part of?
>
>> , it attempts to
>> add the expander's other zero-addressed phy to this port.
>>
>> 3. When adding phy19 to port-7:7:0
>
> Which would be the incorrect thing to do, right? I am basing that on my
> assumption that 7:7:0 is the port which the SATA device is part of.
>
>> , it is prompted that phy19 already
>> belongs to another port, which triggers the current problem.
>>
>> Fix the problem as follows:
>> 1. When ex_phy is added to the parent port, set ex_phy->port to
>> ex_dev->parent_port.
>>
>> 2. Set ex_dev->parent_port to NULL when the parent port's PHY count is 0.
>>
>> 3. When phy->attached_dev_type != NO_DEVICE, do not set the zero address
>> for phy->attached_sas_addr.
>>
>> Fixes: 2908d778ab3e ("[SCSI] aic94xx: new driver")
>> Fixes: 7d1d86518118 ("[SCSI] libsas: fix false positive 'device
>> attached' conditions")
>> Signed-off-by: Xingui Yang <[email protected]>
>> ---
>> v3 -> v4:
>> 1. Update patch title and comments based on John's suggestion.
>>
>> v2 -> v3:
>> 1. Set ex_dev->parent_port to NULL when the number of PHYs of the parent
>>     port becomes 0
>> 2. Update the comments
>>
>> v1 -> v2:
>> 1. Set ex_phy->port with parent_port when ex_phy is added to the
>> parent port
>> 2. Set ex_phy to NULL when free expander
>> 3. Update the comments
>> ---
>>   drivers/scsi/libsas/sas_discover.c | 4 +++-
>>   drivers/scsi/libsas/sas_expander.c | 8 +++++---
>>   drivers/scsi/libsas/sas_internal.h | 1 +
>>   3 files changed, 9 insertions(+), 4 deletions(-)
>>
>> diff --git a/drivers/scsi/libsas/sas_discover.c
>> b/drivers/scsi/libsas/sas_discover.c
>> index 8fb7c41c0962..8eb3888a9e57 100644
>> --- a/drivers/scsi/libsas/sas_discover.c
>> +++ b/drivers/scsi/libsas/sas_discover.c
>> @@ -296,8 +296,10 @@ void sas_free_device(struct kref *kref)
>>       dev->phy = NULL;
>>       /* remove the phys and ports, everything else should be gone */
>> -    if (dev_is_expander(dev->dev_type))
>> +    if (dev_is_expander(dev->dev_type)) {
>>           kfree(dev->ex_dev.ex_phy);
>> +        dev->ex_dev.ex_phy = NULL;
>
> This is strange, as we free the dev later. Where can dev->ex_dev.ex_phy
> be checked before dev is freed?
Yes, I saw this when locating this problem and detecting resource
release. Usually after calling kfree, we will set the pointer to null.
It has little to do with the current problem. I can delete this part of
the modification.

>
>> +    }
>>       if (dev_is_sata(dev) && dev->sata_dev.ap) {
>>           ata_sas_tport_delete(dev->sata_dev.ap);
>> diff --git a/drivers/scsi/libsas/sas_expander.c
>> b/drivers/scsi/libsas/sas_expander.c
>> index a2204674b680..89d44a9dc4e3 100644
>> --- a/drivers/scsi/libsas/sas_expander.c
>> +++ b/drivers/scsi/libsas/sas_expander.c
>> @@ -239,8 +239,7 @@ static void sas_set_ex_phy(struct domain_device
>> *dev, int phy_id,
>>       /* help some expanders that fail to zero sas_address in the 'no
>>        * device' case
>>        */
>> -    if (phy->attached_dev_type == SAS_PHY_UNUSED ||
>> -        phy->linkrate < SAS_LINK_RATE_1_5_GBPS)
>> +    if (phy->attached_dev_type == SAS_PHY_UNUSED)
>>           memset(phy->attached_sas_addr, 0, SAS_ADDR_SIZE);
>>       else
>>           memcpy(phy->attached_sas_addr, dr->attached_sas_addr,
>> SAS_ADDR_SIZE);
>> @@ -1844,9 +1843,12 @@ static void sas_unregister_devs_sas_addr(struct
>> domain_device *parent,
>>       if (phy->port) {
>>           sas_port_delete_phy(phy->port, phy->phy);
>>           sas_device_set_phy(found, phy->port);
>> -        if (phy->port->num_phys == 0)
>> +        if (phy->port->num_phys == 0) {
>>               list_add_tail(&phy->port->del_list,
>>                   &parent->port->sas_port_del_list);
>> +            if (ex_dev->parent_port == phy->port)
>> +                ex_dev->parent_port = NULL;
>> +        }
>>           phy->port = NULL;
>>       }
>>   }
>> diff --git a/drivers/scsi/libsas/sas_internal.h
>> b/drivers/scsi/libsas/sas_internal.h
>> index 3804aef165ad..e860d5b19880 100644
>> --- a/drivers/scsi/libsas/sas_internal.h
>> +++ b/drivers/scsi/libsas/sas_internal.h
>> @@ -202,6 +202,7 @@ static inline void sas_add_parent_port(struct
>> domain_device *dev, int phy_id)
>>           sas_port_mark_backlink(ex->parent_port);
>>       }
>>       sas_port_add_phy(ex->parent_port, ex_phy->phy);
>> +    ex_phy->port = ex->parent_port;
>
> We already do this in sas_ex_join_wide_port(), right?
No, If the addr of ex_phy matches dev->parent, sas_ex_join_wide_port()
will not be called, but sas_add_parent_port() will be called as follows:
static int sas_ex_discover_dev(struct domain_device *dev, int phy_id)
{
struct expander_device *ex = &dev->ex_dev;
struct ex_phy *ex_phy = &ex->ex_phy[phy_id];
struct domain_device *child = NULL;
int res = 0;

<...>
/* Parent and domain coherency */
if (!dev->parent && sas_phy_match_port_addr(dev->port, ex_phy)) {
sas_add_parent_port(dev, phy_id);
return 0;
}
if (dev->parent && sas_phy_match_dev_addr(dev->parent, ex_phy)) {
sas_add_parent_port(dev, phy_id);
if (ex_phy->routing_attr == TABLE_ROUTING)
sas_configure_phy(dev, phy_id,
dev->port->sas_addr, 1);
return 0;
}
<...>
}

>
> I am not saying that what we do now does not have a problem - I am just
> trying to understand what currently happens

ok, because ex_phy->port is not set when calling sas_add_parent_port(),
when deleting phy from the parent wide port, it is not removed from the
phy_list of the parent wide port as follows:
static void sas_unregister_devs_sas_addr(struct domain_device *parent,
int phy_id, bool last)
{
<...>
// Since ex_phy->port is not set, this branch will not be enter
if (phy->port) {
sas_port_delete_phy(phy->port, phy->phy);
sas_device_set_phy(found, phy->port);
if (phy->port->num_phys == 0) {
list_add_tail(&phy->port->del_list,
&parent->port->sas_port_del_list);
if (ex_dev->parent_port == phy->port)
ex_dev->parent_port = NULL;
}
phy->port = NULL;
}
}

Thanks,
Xingui
.

2023-11-24 08:13:44

by Xingui Yang

[permalink] [raw]
Subject: Re: [PATCH v4] scsi: libsas: Fix the failure of adding phy with zero-address to port


Hi, John

Sorry, I missed the reply to you. The improved version is as follows.

On 2023/11/23 22:52, John Garry wrote:
> On 17/11/2023 09:00, Xingui Yang wrote:
>
> Sorry for being slow to come back to this. However I still have
> questions...
>
>> When connecting to the epander device, first disable and then enable the
>
> /s/epander/expander >
> And connecting what to the expander? Is it a SATA disk?
>
> Or the SATA disk is already attached to the expander and we are now
> attaching the expander to the host?
Yes, the SATA disk is already attached to the expander.
>
> It is hard to follow this.
>
>> local phy.
>
> So is the local phy disabled initially? Or is was it initially enabled
> and we disable+re-enable just when attaching, so that there is a race?

When local phy is enabled and disabled repeatedly, the ex_phy status
causing the expander may change, such as being removed. And the link
rate of the SATA device has also changed, such as becoming
SAS_PHY_RESET_IN_PROGRESS.

>
>> The following BUG() will be triggered with a small probability:
>>
>> [562240.051046] sas: phy19 part of wide port with phy16
>
> Where is this print in the code? I see "part of a wide port with
> phy%02d" in sas_discover_dev()

In sas_rediscover() as follow, the latest printing has changed a bit,
what I posted is an old version of the log. The latest version also has
similar problems.
static int sas_rediscover(struct domain_device *dev, const int phy_id)
{
struct expander_device *ex = &dev->ex_dev;
struct ex_phy *changed_phy = &ex->ex_phy[phy_id];
int i;
bool last = true; /* is this the last phy of the port */

for (i = 0; i < ex->num_phys; i++) {
struct ex_phy *phy = &ex->ex_phy[i];

if (i == phy_id)
continue;
if (SAS_ADDR(phy->attached_sas_addr) ==
SAS_ADDR(changed_phy->attached_sas_addr)) {
SAS_DPRINTK("phy%d part of wide port with "
"phy%d\n", phy_id, i);
last = false;
break;
}
}
return sas_rediscover_dev(dev, phy_id, last);
}
>
>> [562240.051197] sas: ex 500e004aaaaaaa1f phy19:U:0 attached:
>> 0000000000000000 (no device)
>> [562240.051203] sas: done REVALIDATING DOMAIN on port 0, pid:435909,
>> res 0x0
>> <...>
>> [562240.062536] sas: ex 500e004aaaaaaa1f phy0 new device attached
>> [562240.062616] sas: ex 500e004aaaaaaa1f phy00:U:5 attached:
>> 0000000000000000 (stp)
>> [562240.062680]  port-7:7:0: trying to add phy phy-7:7:19 fails: it's
>> already part of another port
>> [562240.085064] ------------[ cut here ]------------
>> [562240.096612] kernel BUG at drivers/scsi/scsi_transport_sas.c:1083!
>> [562240.109611] Internal error: Oops - BUG: 0 [#1] SMP
>> [562240.343518] Process kworker/u256:3 (pid: 435909, stack limit =
>> 0x0000000003bcbebf)
>> [562240.421714] Workqueue: 0000:b4:02.0_disco_q sas_revalidate_domain
>> [libsas]
>> [562240.437173] pstate: 40c00009 (nZcv daif +PAN +UAO)
>> [562240.450478] pc : sas_port_add_phy+0x13c/0x168 [scsi_transport_sas]
>> [562240.465283] lr : sas_port_add_phy+0x13c/0x168 [scsi_transport_sas]
>> [562240.479751] sp : ffff0000300cfa70
>> [562240.674822] Call trace:
>> [562240.682709]  sas_port_add_phy+0x13c/0x168 [scsi_transport_sas]
>> [562240.694013]  sas_ex_get_linkrate.isra.5+0xcc/0x128 [libsas]
>> [562240.704957]  sas_ex_discover_end_dev+0xfc/0x538 [libsas]
>> [562240.715508]  sas_ex_discover_dev+0x3cc/0x4b8 [libsas]
>> [562240.725634]  sas_ex_discover_devices+0x9c/0x1a8 [libsas]
>> [562240.735855]  sas_ex_revalidate_domain+0x2f0/0x450 [libsas]
>> [562240.746123]  sas_revalidate_domain+0x158/0x160 [libsas]
>> [562240.756014]  process_one_work+0x1b4/0x448
>> [562240.764548]  worker_thread+0x54/0x468
>> [562240.772562]  kthread+0x134/0x138
>> [562240.779989]  ret_from_fork+0x10/0x18
>>
>> What causes this problem:
>> 1. When phy19 was initially added to the parent port, ex_phy->port was
>> not
>
> phy19 is the expander phy attached to the host, right?
Yes.
>
>> set. As a result, when phy19 was removed from the parent wide port,
>
> You seem to be getting ahead of yourself. It has not been mentioned when
> phy19 is removed from the parent wide port.
Expander broadcast event notification phy 19 has been disconnected as
follows:
[562240.048606] sas: broadcast received: 0
[562240.048615] sas: REVALIDATING DOMAIN on port 0, pid:435909
[562240.048929] sas: Expander phy change count has changed
[562240.051038] sas: ex 500e004aaaaaaa1f phy0 originated BROADCAST(CHANGE)
[562240.051039] sas: ex 500e004aaaaaaa1f phy1 originated BROADCAST(CHANGE)
[562240.051040] sas: ex 500e004aaaaaaa1f phy2 originated BROADCAST(CHANGE)
[562240.051040] sas: ex 500e004aaaaaaa1f phy3 originated BROADCAST(CHANGE)
[562240.051041] sas: ex 500e004aaaaaaa1f phy4 originated BROADCAST(CHANGE)
[562240.051042] sas: ex 500e004aaaaaaa1f phy5 originated BROADCAST(CHANGE)
[562240.051043] sas: ex 500e004aaaaaaa1f phy17 originated BROADCAST(CHANGE)
[562240.051044] sas: ex 500e004aaaaaaa1f phy18 originated BROADCAST(CHANGE)
[562240.051044] sas: ex 500e004aaaaaaa1f phy19 originated BROADCAST(CHANGE)
[562240.051046] sas: phy19 part of wide port with phy16
[562240.051197] sas: ex 500e004aaaaaaa1f phy19:U:0 attached:
0000000000000000 (no device)
[562240.051198] sas: ex 500e004aaaaaaa1f phy20 originated BROADCAST(CHANGE)
[562240.051198] sas: ex 500e004aaaaaaa1f phy22 originated BROADCAST(CHANGE)
[562240.051199] sas: ex 500e004aaaaaaa1f phy23 originated BROADCAST(CHANGE)
[562240.051203] sas: done REVALIDATING DOMAIN on port 0, pid:435909, res 0x0
[562240.051221] sas: broadcast received: 0
[562240.051230] sas: REVALIDATING DOMAIN on port 0, pid:435909
[562240.051413] sas: Expander phy change count has changed
[562240.053439] sas: ex 500e004aaaaaaa1f phy0 originated BROADCAST(CHANGE)
[562240.053439] sas: ex 500e004aaaaaaa1f phy1 originated BROADCAST(CHANGE)
[562240.053440] sas: ex 500e004aaaaaaa1f phy2 originated BROADCAST(CHANGE)
[562240.053441] sas: ex 500e004aaaaaaa1f phy3 originated BROADCAST(CHANGE)
[562240.053442] sas: ex 500e004aaaaaaa1f phy4 originated BROADCAST(CHANGE)
[562240.053443] sas: ex 500e004aaaaaaa1f phy5 originated BROADCAST(CHANGE)
[562240.053444] sas: ex 500e004aaaaaaa1f phy17 originated BROADCAST(CHANGE)
[562240.053444] sas: ex 500e004aaaaaaa1f phy18 originated BROADCAST(CHANGE)
[562240.053445] sas: ex 500e004aaaaaaa1f phy20 originated BROADCAST(CHANGE)
[562240.053446] sas: ex 500e004aaaaaaa1f phy22 originated BROADCAST(CHANGE)
[562240.053447] sas: ex 500e004aaaaaaa1f phy23 originated BROADCAST(CHANGE)
[562240.053448] sas: ex 500e004aaaaaaa1f phy0 new device attached
[562240.053521] sas: ex 500e004aaaaaaa1f phy00:U:5 attached:
0000000000000000 (no device)
[562240.053522] sas: ex 500e004aaaaaaa1f phy1 new device attached
[562240.053601] sas: ex 500e004aaaaaaa1f phy01:U:5 attached:
0000000000000000 (no device)
[562240.053602] sas: ex 500e004aaaaaaa1f phy2 new device attached
[562240.053682] sas: ex 500e004aaaaaaa1f phy02:U:5 attached:
0000000000000000 (no device)
[562240.053684] sas: ex 500e004aaaaaaa1f phy3 new device attached
[562240.053763] sas: ex 500e004aaaaaaa1f phy03:U:5 attached:
0000000000000000 (no device)
[562240.053764] sas: ex 500e004aaaaaaa1f phy4 new device attached
[562240.053843] sas: ex 500e004aaaaaaa1f phy04:U:5 attached:
0000000000000000 (no device)
[562240.053844] sas: ex 500e004aaaaaaa1f phy5 new device attached
[562240.053924] sas: ex 500e004aaaaaaa1f phy05:U:5 attached:
0000000000000000 (no device)
[562240.053925] sas: ex 500e004aaaaaaa1f phy17 new device attached
[562240.054008] sas: ex 500e004aaaaaaa1f phy17:U:B attached:
5001882016000002 (host)
[562240.054015] sas: ex 500e004aaaaaaa1f phy18 new device attached
[562240.054098] sas: ex 500e004aaaaaaa1f phy18:U:B attached:
5001882016000002 (host)
[562240.054102] sas: ex 500e004aaaaaaa1f phy20 new device attached
[562240.054186] sas: ex 500e004aaaaaaa1f phy20:U:B attached:
5001882016000002 (host)
[562240.054190] sas: ex 500e004aaaaaaa1f phy22 new device attached
[562240.054273] sas: ex 500e004aaaaaaa1f phy22:U:B attached:
5001882016000002 (host)
[562240.054276] sas: ex 500e004aaaaaaa1f phy23 new device attached
[562240.054360] sas: ex 500e004aaaaaaa1f phy23:U:B attached:
5001882016000002 (host)
[562240.054364] sas: done REVALIDATING DOMAIN on port 0, pid:435909, res 0x0
>
>> it was
>> not deleted from the phy_list of the parent port.
>>
>> 2. The rate of the newly connected SATA device to phy0 is less than 1.5G,
>> and its sas_address was set to 0. After creating port 7:7:0
>
> is 7:7:0 the port which the SATA device is part of?
>
>> , it attempts to
>> add the expander's other zero-addressed phy to this port.
>>
>> 3. When adding phy19 to port-7:7:0
It's a new port create by phy00:U:5. after the log:
[562240.062536] sas: ex 500e004aaaaaaa1f phy0 new device attached
[562240.062616] sas: ex 500e004aaaaaaa1f phy00:U:5 attached:
0000000000000000 (stp)
>
> Which would be the incorrect thing to do, right? I am basing that on my
> assumption that 7:7:0 is the port which the SATA device is part of.
Yes. It is created by the sata device with zero address.

Thanks,
Xingui

2023-11-27 19:29:29

by John Garry

[permalink] [raw]
Subject: Re: [PATCH v4] scsi: libsas: Fix the failure of adding phy with zero-address to port

On 24/11/2023 02:27, yangxingui wrote:
>> We already do this in sas_ex_join_wide_port(), right?
> No, If the addr of ex_phy matches dev->parent, sas_ex_join_wide_port()
> will not be called, but sas_add_parent_port() will be called  as follows:
> static int sas_ex_discover_dev(struct domain_device *dev, int phy_id)
> {
>         struct expander_device *ex = &dev->ex_dev;
>         struct ex_phy *ex_phy = &ex->ex_phy[phy_id];
>         struct domain_device *child = NULL;
>         int res = 0;
>
>     <...>
>         /* Parent and domain coherency */
>         if (!dev->parent && sas_phy_match_port_addr(dev->port, ex_phy)) {
>                 sas_add_parent_port(dev, phy_id);
>                 return 0;
>         }
>         if (dev->parent && sas_phy_match_dev_addr(dev->parent, ex_phy)) {
>                 sas_add_parent_port(dev, phy_id);
>                 if (ex_phy->routing_attr == TABLE_ROUTING)
>                         sas_configure_phy(dev, phy_id,
> dev->port->sas_addr, 1);
>                 return 0;
>         }
>     <...>
> }
>
>>
>> I am not saying that what we do now does not have a problem - I am
>> just trying to understand what currently happens
>
> ok, because ex_phy->port is not set when calling sas_add_parent_port(),
> when deleting phy from the parent wide port, it is not removed from the
> phy_list of the parent wide port as follows:
> static void sas_unregister_devs_sas_addr(struct domain_device *parent,
>                                          int phy_id, bool last)
> {
>     <...>
>     // Since ex_phy->port is not set, this branch will not be enter

But then how does this ever work? It is because we follow path
sas_rediscover_dev() -> sas_discover_new() -> sas_ex_discover_devices()
-> sas_ex_discover_dev() -> sas_add_parent_port(), and not
sas_rediscover_dev() -> sas_discover_new() -> sas_ex_join_wide_port()?
If so, is that because ephy->sas_attached_phy == 0 in sas_discover_new()
-> sas_ex_join_wide_port() and it fails?

BTW, about something mentioned earlier - adding the phy19 with SAS_ADDR
= 0 ever to a sas_port seems wrong.

>         if (phy->port) {
>                 sas_port_delete_phy(phy->port, phy->phy);
>                 sas_device_set_phy(found, phy->port);
>                 if (phy->port->num_phys == 0) {
>                         list_add_tail(&phy->port->del_list,
>                                 &parent->port->sas_port_del_list);
>                         if (ex_dev->parent_port == phy->port)
>                                 ex_dev->parent_port = NULL;
>                 }
>                 phy->port = NULL;
>         }
> }

Thanks,
John

2023-11-28 03:46:24

by Xingui Yang

[permalink] [raw]
Subject: Re: [PATCH v4] scsi: libsas: Fix the failure of adding phy with zero-address to port

Hi John,

On 2023/11/28 3:28, John Garry wrote:
> On 24/11/2023 02:27, yangxingui wrote:
>>> We already do this in sas_ex_join_wide_port(), right?
>> No, If the addr of ex_phy matches dev->parent, sas_ex_join_wide_port()
>> will not be called, but sas_add_parent_port() will be called  as follows:
>> static int sas_ex_discover_dev(struct domain_device *dev, int phy_id)
>> {
>>          struct expander_device *ex = &dev->ex_dev;
>>          struct ex_phy *ex_phy = &ex->ex_phy[phy_id];
>>          struct domain_device *child = NULL;
>>          int res = 0;
>>
>>      <...>
>>          /* Parent and domain coherency */
>>          if (!dev->parent && sas_phy_match_port_addr(dev->port,
>> ex_phy)) {
>>                  sas_add_parent_port(dev, phy_id);
>>                  return 0;
>>          }
>>          if (dev->parent && sas_phy_match_dev_addr(dev->parent,
>> ex_phy)) {
>>                  sas_add_parent_port(dev, phy_id);
>>                  if (ex_phy->routing_attr == TABLE_ROUTING)
>>                          sas_configure_phy(dev, phy_id,
>> dev->port->sas_addr, 1);
>>                  return 0;
>>          }
>>      <...>
>> }
>>
>>>
>>> I am not saying that what we do now does not have a problem - I am
>>> just trying to understand what currently happens
>>
>> ok, because ex_phy->port is not set when calling
>> sas_add_parent_port(), when deleting phy from the parent wide port, it
>> is not removed from the phy_list of the parent wide port as follows:
>> static void sas_unregister_devs_sas_addr(struct domain_device *parent,
>>                                           int phy_id, bool last)
>> {
>>      <...>
>>      // Since ex_phy->port is not set, this branch will not be enter
>
> But then how does this ever work? It is because we follow path
> sas_rediscover_dev() -> sas_discover_new() -> sas_ex_discover_devices()
> -> sas_ex_discover_dev() -> sas_add_parent_port(), and not
> sas_rediscover_dev() -> sas_discover_new() -> sas_ex_join_wide_port()?
> If so, is that because ephy->sas_attached_phy == 0 in sas_discover_new()
> -> sas_ex_join_wide_port() and it fails?
>
> BTW, about something mentioned earlier - adding the phy19 with SAS_ADDR

Yes,
For phy19, when the phy is attached and added to the parent wide port,
the path is:
sas_rediscover()
->sas_discover_new()
->sas_ex_discover_devices()
->sas_ex_discover_dev()
-> sas_add_parent_port().
And the path called when it is removed from parent wide port is:
sas_rediscover()
->sas_unregister_devs_sas_addr() // The sas address of phy19 becomes 0.
Since ex_phy->port is NULL, phy19 is not removed from the parent wide
port's phy_list.

For phy0, it is connected to a new sata device.
sas_rediscover()
->sas_discover_new()->sas_ex_phy_discover()
->sas_ex_phy_discover_helper()
->sas_set_ex_phy() // The device type is stp. Since the linkrate
is 5 and less than 1.5G, sas_address is set to 0.
->sas_ex_discover_devices()
->sas_ex_discover_dev()
->sas_ex_discover_end_dev()
->sas_port_alloc() // Create port-7:7:0
->sas_ex_get_linkrate()
->sas_port_add_phy() // Try adding phy19 to port->7:7:0,
triggering BUG()

Thanks,
Xingui
.