Document new enable-gpio field. It can be used to disable the part
without turning down its regulator.
Cc: [email protected]
Signed-off-by: Ricardo Ribalda Delgado <[email protected]>
Acked-by: Pavel Machek <[email protected]>
---
Documentation/devicetree/bindings/media/i2c/ad5820.txt | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/Documentation/devicetree/bindings/media/i2c/ad5820.txt b/Documentation/devicetree/bindings/media/i2c/ad5820.txt
index 5940ca11c021..db596e8eb0ba 100644
--- a/Documentation/devicetree/bindings/media/i2c/ad5820.txt
+++ b/Documentation/devicetree/bindings/media/i2c/ad5820.txt
@@ -8,6 +8,11 @@ Required Properties:
- VANA-supply: supply of voltage for VANA pin
+Optional properties:
+
+ - enable-gpios : GPIO spec for the XSHUTDOWN pin. The XSHUTDOWN signal is
+active low, a high level on the pin enables the device.
+
Example:
ad5820: coil@c {
@@ -15,5 +20,6 @@ Example:
reg = <0x0c>;
VANA-supply = <&vaux4>;
+ enable-gpios = <&msmgpio 26 GPIO_ACTIVE_HIGH>;
};
--
2.19.0
Hi Ricardo,
Thank you for the patch.
On Tuesday, 2 October 2018 14:13:56 EEST Ricardo Ribalda Delgado wrote:
> Document new enable-gpio field. It can be used to disable the part
> without turning down its regulator.
>
> Cc: [email protected]
> Signed-off-by: Ricardo Ribalda Delgado <[email protected]>
> Acked-by: Pavel Machek <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
> ---
> Documentation/devicetree/bindings/media/i2c/ad5820.txt | 6 ++++++
> 1 file changed, 6 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/ad5820.txt
> b/Documentation/devicetree/bindings/media/i2c/ad5820.txt index
> 5940ca11c021..db596e8eb0ba 100644
> --- a/Documentation/devicetree/bindings/media/i2c/ad5820.txt
> +++ b/Documentation/devicetree/bindings/media/i2c/ad5820.txt
> @@ -8,6 +8,11 @@ Required Properties:
>
> - VANA-supply: supply of voltage for VANA pin
>
> +Optional properties:
> +
> + - enable-gpios : GPIO spec for the XSHUTDOWN pin. The XSHUTDOWN signal
> is +active low, a high level on the pin enables the device.
> +
> Example:
>
> ad5820: coil@c {
> @@ -15,5 +20,6 @@ Example:
> reg = <0x0c>;
>
> VANA-supply = <&vaux4>;
> + enable-gpios = <&msmgpio 26 GPIO_ACTIVE_HIGH>;
> };
--
Regards,
Laurent Pinchart
On Tue, 2 Oct 2018 13:13:56 +0200, Ricardo Ribalda Delgado wrote:
> Document new enable-gpio field. It can be used to disable the part
> without turning down its regulator.
>
> Cc: [email protected]
> Signed-off-by: Ricardo Ribalda Delgado <[email protected]>
> Acked-by: Pavel Machek <[email protected]>
> ---
> Documentation/devicetree/bindings/media/i2c/ad5820.txt | 6 ++++++
> 1 file changed, 6 insertions(+)
>
Reviewed-by: Rob Herring <[email protected]>