From: admin01 <admin01@admin01-desktop.(none)>
* STMicroelectronics version 1.2.0, Copyright (C) 2010
* STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
* This is free software, and you are welcome to redistribute it
* under certain conditions.
This is the driver for TPM chip from ST Microelectronics.
If you have a TPM security chip from STMicroelectronics working with
an I2C/SPI, in menuconfig or .config choose the tpm driver on
device --> tpm and activate the protocol of your choice before compiling
the kernel.
The driver will be accessible from within Linux.
Tested on linux x86/x64 and beagleboard REV B & XM REV C
Signed-off-by: admin01 <admin01@admin01-desktop.(none)>
---
arch/arm/mach-omap2/board-omap3beagle.c | 40 ++
drivers/char/tpm/Kconfig | 10 +
drivers/char/tpm/Makefile | 1 +
drivers/char/tpm/tpm_spi_stm_st33.c | 1116 +++++++++++++++++++++++++++++++
drivers/char/tpm/tpm_spi_stm_st33.h | 75 ++
include/linux/spi/tpm_spi_stm_st33.h | 46 ++
6 files changed, 1287 insertions(+), 0 deletions(-)
create mode 100644 drivers/char/tpm/tpm_spi_stm_st33.c
create mode 100644 drivers/char/tpm/tpm_spi_stm_st33.h
create mode 100644 include/linux/spi/tpm_spi_stm_st33.h
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index c3558f9..72e6513 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -46,6 +46,11 @@
#include <video/omap-panel-tfp410.h>
#include <linux/platform_data/mtd-nand-omap2.h>
+#ifdef CONFIG_TCG_ST33_SPI
+#include <linux/spi/tpm_spi_stm_st33.h>
+#include <linux/spi/spi.h>
+#endif /* CONFIG_TCG_ST33_SPI */
+
#include "common.h"
#include "omap_device.h"
#include "gpmc.h"
@@ -375,6 +380,26 @@ static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
},
};
+#if defined CONFIG_TCG_ST33_I2C || defined CONFIG_TCG_ST33_SPI
+static struct st33zp24_platform_data tpm_data = {
+ .io_serirq = 136,
+ .io_lpcpd = 143,
+};
+#endif
+
+#ifdef CONFIG_TCG_ST33_SPI
+static struct spi_board_info tpm_st33_spi_board_info[] = {
+ {
+ .modalias = TPM_ST33_SPI,
+ .max_speed_hz = 10000000,
+ .bus_num = 4,
+ .chip_select = 0,
+ .mode = SPI_MODE_0,
+ .platform_data = &tpm_data,
+ },
+};
+#endif
+
static int __init omap3_beagle_i2c_init(void)
{
omap3_pmic_get_config(&beagle_twldata,
@@ -556,6 +581,20 @@ static void __init omap3_beagle_init(void)
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
+ #if defined CONFIG_TCG_ST33_I2C || defined CONFIG_TCG_ST33_SPI
+ omap_mux_init_gpio(tpm_data.io_serirq, OMAP_PIN_INPUT);
+ omap_mux_init_gpio(tpm_data.io_lpcpd, OMAP_PIN_OUTPUT);
+ #endif
+
+ #ifdef CONFIG_TCG_ST33_SPI
+ omap_mux_init_signal("mcspi4_clk", OMAP_PIN_INPUT);
+ omap_mux_init_signal("mcspi4_cs0", OMAP_PIN_OUTPUT);
+ omap_mux_init_signal("mcspi4_simo", OMAP_PIN_OUTPUT);
+ omap_mux_init_signal("mcspi4_somi", OMAP_PIN_INPUT);
+
+ spi_register_board_info(tpm_st33_spi_board_info,
+ ARRAY_SIZE(tpm_st33_spi_board_info));
+ #endif
+
pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup));
}
diff --git a/drivers/char/tpm/Kconfig b/drivers/char/tpm/Kconfig
index dbfd564..2fc1254 100644
--- a/drivers/char/tpm/Kconfig
+++ b/drivers/char/tpm/Kconfig
@@ -91,4 +91,14 @@ config TCG_ST33_I2C
To compile this driver as a module, choose M here; the module will be
called tpm_stm_st33_i2c.
+config TCG_ST33_SPI
+ tristate "STMicroelectronics ST33 SPI"
+ depends on SPI
+ depends on GPIOLIB
+ ---help---
+ If you have a TPM security chip from STMicroelectronics working with
+ an SPI bus say Yes and it will be accessible from within Linux.
+ To compile this driver as a module, choose M here; the module will be
+ called tpm_stm_st33_spi.
+
endif # TCG_TPM
diff --git a/drivers/char/tpm/Makefile b/drivers/char/tpm/Makefile
index a3736c9..a1db3dd 100644
--- a/drivers/char/tpm/Makefile
+++ b/drivers/char/tpm/Makefile
@@ -18,3 +18,4 @@ obj-$(CONFIG_TCG_ATMEL) += tpm_atmel.o
obj-$(CONFIG_TCG_INFINEON) += tpm_infineon.o
obj-$(CONFIG_TCG_IBMVTPM) += tpm_ibmvtpm.o
obj-$(CONFIG_TCG_ST33_I2C) += tpm_i2c_stm_st33.o
+obj-$(CONFIG_TCG_ST33_SPI) += tpm_spi_stm_st33.o
diff --git a/drivers/char/tpm/tpm_spi_stm_st33.c b/drivers/char/tpm/tpm_spi_stm_st33.c
new file mode 100644
index 0000000..a47c647
--- /dev/null
+++ b/drivers/char/tpm/tpm_spi_stm_st33.c
@@ -0,0 +1,1116 @@
+/*
+ * STMicroelectronics TPM SPI Linux driver for TPM ST33ZP24
+ * Copyright (C) 2009, 2010 STMicroelectronics
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ * STMicroelectronics version 1.2.0, Copyright (C) 2010
+ * STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
+ * This is free software, and you are welcome to redistribute it
+ * under certain conditions.
+ *
+ * @Author: Christophe RICARD [email protected]
+ *
+ * @File: tpm_stm_st33_spi.c
+ *
+ * @Synopsis:
+ * 09/15/2010: First shot driver tpm_tis driver for lpc is
+ * used as model.
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/spi/spi.h>
+#include <linux/wait.h>
+#include <linux/string.h>
+#include <linux/interrupt.h>
+#include <linux/spinlock.h>
+#include <linux/sysfs.h>
+#include <linux/gpio.h>
+#include <linux/sched.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/sched.h>
+
+#include <linux/spi/tpm_spi_stm_st33.h>
+
+#include "tpm.h"
+
+#include "tpm_spi_stm_st33.h"
+
+#ifdef DEBUG
+#define FUNC_ENTER() pr_info("%s\n", __func__)
+#else
+#define FUNC_ENTER() do {} while (0)
+#endif
+
+enum stm33zp24_access {
+ TPM_ACCESS_VALID = 0x80,
+ TPM_ACCESS_ACTIVE_LOCALITY = 0x20,
+ TPM_ACCESS_REQUEST_PENDING = 0x04,
+ TPM_ACCESS_REQUEST_USE = 0x02,
+};
+
+enum stm33zp24_status {
+ TPM_STS_VALID = 0x80,
+ TPM_STS_COMMAND_READY = 0x40,
+ TPM_STS_GO = 0x20,
+ TPM_STS_DATA_AVAIL = 0x10,
+ TPM_STS_DATA_EXPECT = 0x08,
+};
+
+enum stm33zp24_int_flags {
+ TPM_GLOBAL_INT_ENABLE = 0x80,
+ TPM_INTF_CMD_READY_INT = 0x080,
+ TPM_INTF_FIFO_AVALAIBLE_INT = 0x040,
+ TPM_INTF_WAKE_UP_READY_INT = 0x020,
+ TPM_INTF_LOC4SOFTRELEASE_INT = 0x008,
+ TPM_INTF_LOCALITY_CHANGE_INT = 0x004,
+ TPM_INTF_STS_VALID_INT = 0x002,
+ TPM_INTF_DATA_AVAIL_INT = 0x001,
+};
+
+enum tis_defaults {
+ TIS_SHORT_TIMEOUT = 750, /* ms */
+ TIS_LONG_TIMEOUT = 2000, /* 2 sec */
+};
+
+/*
+ * write8_reg
+ * Send byte to the TIS register according to the ST33ZP24 SPI protocol.
+ * @param: tpm, the chip description
+ * @param: tpm_register, the tpm tis register where the data should be written
+ * @param: tpm_data, the tpm_data to write inside the tpm_register
+ * @param: tpm_size, The length of the data
+ * @return: number of byte written successfully: should be one if success.
+ */
+static int write8_reg(struct tpm_chip *tpm, u8 tpm_register,
+ u8 *tpm_data, u16 tpm_size)
+{
+ /* u8 LOC+DIR u8 ADD u16 LENGHT u8* data */
+ /* u8 LATENCY u8 LATENCY */
+
+ u8 data;
+ int i = 0, j;
+ int value = 0;
+ struct spi_device *dev = (struct spi_device *) tpm->vendor.iobase;
+ struct st33zp24_platform_data *platform_data = dev->dev.platform_data;
+ u8 *data_buffer = platform_data->tpm_spi_buffer[0];
+ struct spi_transfer xfer = {
+ .tx_buf = data_buffer,
+ .rx_buf = platform_data->tpm_spi_buffer[1],
+ };
+ struct spi_message msg;
+ u8 latency = platform_data->latency + tpm_size + 1;
+
+
+ FUNC_ENTER();
+ /* Pre-Header */
+
+ data = TPM_WRITE_DIRECTION | tpm->vendor.locality;
+ memcpy(data_buffer + i, &data, sizeof(data));
+ i++;
+ data = tpm_register;
+ memcpy(data_buffer + i, &data, sizeof(data));
+ i++;
+
+ if (tpm_size > 0 &&
+ (tpm_register == TPM_DATA_FIFO ||
+ tpm_register == TPM_HASH_DATA)) {
+ data = tpm_size >> 8 & 0x00ff;
+ memcpy(data_buffer + i, &data, sizeof(data));
+ i++;
+ data = tpm_size & 0x00ff;
+ memcpy(data_buffer + i, &data, sizeof(data));
+ i++;
+ latency -= 2;
+ }
+
+ memcpy(data_buffer + i, tpm_data, tpm_size);
+ i += tpm_size;
+
+ for (j = 0 ; j < platform_data->latency + 1; j++) {
+ data = TPM_DUMMY_BYTE;
+ memcpy(data_buffer + i, &data, sizeof(data));
+ i++;
+ }
+ xfer.len = i;
+ spi_message_init(&msg);
+ spi_message_add_tail(&xfer, &msg);
+ value = spi_sync(dev, &msg);
+
+ if (value == 0) {
+ j = i - 1 - j;
+ for (; j < i && ((u8 *) xfer.rx_buf)[j] == 0; j++)
+ ;
+
+ if (((u8 *) xfer.rx_buf)[j] != 0)
+ value = ((u8 *) xfer.rx_buf)[j];
+ }
+
+ return value;
+} /* write8_reg() */
+
+/*
+ * read8_reg
+ * Recv byte from the TIS register according to the ST33ZP24 SPI protocol.
+ * @param: tpm, the chip description
+ * @param: tpm_register, the tpm tis register where the data should be read
+ * @param: tpm_data, the TPM response
+ * @param: tpm_size, tpm TPM response size to read.
+ * @return: number of byte read successfully: should be one if success.
+ */
+static u8 read8_reg(struct tpm_chip *tpm, u8 tpm_register,
+ u8 *tpm_data, u16 tpm_size)
+{
+ u8 data;
+ int i = 0, j;
+ int value = 0;
+ struct spi_device *dev = (struct spi_device *) tpm->vendor.iobase;
+ struct st33zp24_platform_data *platform_data = dev->dev.platform_data;
+ u8 *data_buffer = platform_data->tpm_spi_buffer[0];
+ struct spi_transfer xfer = {
+ .tx_buf = data_buffer,
+ .rx_buf = platform_data->tpm_spi_buffer[1],
+ };
+ struct spi_message msg;
+
+ u8 latency = platform_data->latency + tpm_size + 1;
+
+ FUNC_ENTER();
+ /* Pre-Header */
+
+ data = tpm->vendor.locality;
+ memcpy(data_buffer + i, &data, sizeof(data));
+ i++;
+ data = tpm_register;
+ memcpy(data_buffer + i, &data, sizeof(data));
+ i++;
+
+ for (j = 0 ; j < latency; j++) {
+ data = TPM_DUMMY_BYTE;
+ memcpy(data_buffer + i, &data, sizeof(data));
+ i++;
+ }
+ xfer.len = i;
+
+ /* header + status byte + size of the data + status byte */
+ spi_message_init(&msg);
+ spi_message_add_tail(&xfer, &msg);
+ value = spi_sync(dev, &msg);
+ if (tpm_size > 0 && value == 0) {
+ j = 2;
+ for (; j < i && ((u8 *) xfer.rx_buf)[j] == 0; j++)
+ ;
+
+ if (j + 1 < i) {
+ value = ((u8 *) xfer.rx_buf)[j];
+
+ if (tpm_size > 0)
+ memcpy(tpm_data, xfer.rx_buf + j + 1,
+ tpm_size);
+ }
+ }
+ return value;
+} /* read8_reg() */
+
+/*
+ * SPI_WRITE_DATA
+ * Send byte to the TIS register according to the ST33ZP24 SPI protocol.
+ * @param: tpm, the chip description
+ * @param: tpm_register, the tpm tis register where the data should be written
+ * @param: tpm_data, the tpm_data to write inside the tpm_register
+ * @param: tpm_size, The length of the data
+ * @return: number of byte written successfully: should be one if success.
+ */
+static u32 SPI_WRITE_DATA(struct tpm_chip *tpm, u8 tpm_register,
+ u8 *tpm_data, u16 tpm_size)
+{
+ u8 value = 0;
+
+ FUNC_ENTER();
+
+ value = write8_reg(tpm, tpm_register, tpm_data, tpm_size);
+
+ switch (value) {
+ case TPM_ST_SPI_OK:
+ return TPM_ST_SPI_OK;
+ case 0:
+ return 0;
+ default:
+ return -EBUSY;
+ }
+} /* SPI_WRITE_DATA() */
+
+/*
+ * SPI_READ_DATA
+ * Recv byte from the TIS register according to the ST33ZP24 SPI protocol.
+ * @param: tpm, the chip description
+ * @param: tpm_register, the tpm tis register where the data should be read
+ * @param: tpm_data, the TPM response
+ * @param: tpm_size, tpm TPM response size to read.
+ * @return: number of byte read successfully: should be one if success.
+ */
+static u32 SPI_READ_DATA(struct tpm_chip *tpm, u8 tpm_register,
+ u8 *tpm_data, u16 tpm_size)
+{
+ u8 value = 0;
+
+ FUNC_ENTER();
+
+ value = read8_reg(tpm, tpm_register, tpm_data, tpm_size);
+
+ switch (value) {
+ case TPM_ST_SPI_OK:
+ return TPM_ST_SPI_OK;
+ case 0:
+ return 0;
+ default:
+ return -EBUSY;
+ }
+} /* SPI_READ_DATA () */
+
+/*
+ * clear_interruption
+ * clear the TPM interrupt register.
+ * @param: tpm, the chip description
+ */
+static void clear_interruption(struct tpm_chip *tpm)
+{
+ u8 interrupt;
+ SPI_READ_DATA(tpm, TPM_INT_STATUS, &interrupt, 1);
+ /* Clear interrupts handled with TPM_EOI */
+ SPI_WRITE_DATA(tpm, TPM_INT_STATUS, &interrupt, 1);
+ SPI_READ_DATA(tpm, TPM_INT_STATUS, &interrupt, 1);
+} /* clear_interruption() */
+
+/*
+ * _wait_for_interrupt_serirq_timeout
+ * @param: tpm, the chip description
+ * @param: timeout, the timeout of the interrupt
+ * @return: the status of the interruption.
+ */
+static int _wait_for_interrupt_serirq_timeout(struct tpm_chip *chip,
+ unsigned long timeout)
+{
+ unsigned long status;
+ struct spi_device *client;
+ struct st33zp24_platform_data *pin_infos;
+
+ FUNC_ENTER();
+
+ client = (struct spi_device *) chip->vendor.iobase;
+ pin_infos = client->dev.platform_data;
+
+ status = wait_for_completion_interruptible_timeout(
+ &pin_infos->irq_detection, timeout);
+ if (status > 0)
+ enable_irq(gpio_to_irq(pin_infos->io_serirq));
+ gpio_direction_input(pin_infos->io_serirq);
+
+ return status;
+} /* wait_for_interrupt_serirq_timeout() */
+
+unsigned long wait_for_serirq_timeout(struct tpm_chip *chip, bool condition,
+ unsigned long timeout)
+{
+ unsigned long status = 0;
+ struct spi_device *client;
+ struct st33zp24_platform_data *pin_infos;
+
+ client = (struct spi_device *) chip->vendor.iobase;
+ pin_infos = client->dev.platform_data;
+
+ status = _wait_for_interrupt_serirq_timeout(chip, timeout);
+ if (!status) {
+ status = -EBUSY;
+ goto wait_end;
+ }
+ clear_interruption(chip);
+ if (condition)
+ status = 1;
+
+wait_end:
+ return status;
+}
+
+
+/*
+ * tpm_stm_spi_cancel, cancel is not implemented.
+ * @param: chip, the tpm chip description as specified in
+ * driver/char/tpm/tpm.h.
+ */
+static void tpm_stm_spi_cancel(struct tpm_chip *chip)
+{
+ struct spi_device *client;
+ u8 data = TPM_STS_COMMAND_READY;
+ client = (struct spi_device *) chip->vendor.iobase;
+
+ FUNC_ENTER();
+
+ /* this causes the current command to be aborted */
+ SPI_WRITE_DATA(chip, TPM_STS, &data, 1);
+} /* tpm_stm_spi_cancel() */
+
+/*
+ * tpm_stm_spi_status return the TPM_STS register
+ * @param: chip, the tpm chip description
+ * @return: the TPM_STS register value.
+ */
+static u8 tpm_stm_spi_status(struct tpm_chip *chip)
+{
+ struct spi_device *client;
+ u8 data;
+ client = (struct spi_device *) chip->vendor.iobase;
+
+ FUNC_ENTER();
+
+ SPI_READ_DATA(chip, TPM_STS, &data, 1);
+ return data;
+} /* tpm_stm_spi_status() */
+
+
+
+/*
+ * check_locality if the locality is active
+ * @param: chip, the tpm chip description
+ * @return: the active locality or -EACCESS.
+ */
+static int check_locality(struct tpm_chip *chip)
+{
+ struct spi_device *client;
+ u8 data;
+ u8 status;
+
+ FUNC_ENTER();
+
+ client = (struct spi_device *) chip->vendor.iobase;
+
+ status = SPI_READ_DATA(chip, TPM_ACCESS, &data, 1);
+ if (status && (data &
+ (TPM_ACCESS_ACTIVE_LOCALITY | TPM_ACCESS_VALID)) ==
+ (TPM_ACCESS_ACTIVE_LOCALITY | TPM_ACCESS_VALID))
+ return chip->vendor.locality;
+
+ return -EACCES;
+} /* check_locality() */
+
+/*
+ * request_locality request the TPM locality
+ * @param: chip, the chip description
+ * @return: the active locality or EACCESS.
+ */
+static int request_locality(struct tpm_chip *chip)
+{
+ unsigned long stop;
+ long rc;
+ u8 data;
+ struct spi_device *client;
+
+ FUNC_ENTER();
+
+ client = (struct spi_device *) chip->vendor.iobase;
+ /* Check locality */
+ if (check_locality(chip) == chip->vendor.locality)
+ return chip->vendor.locality;
+
+ /* Request locality */
+ data = TPM_ACCESS_REQUEST_USE;
+ rc = SPI_WRITE_DATA(chip, TPM_ACCESS, &data, 1);
+ if (rc < 0)
+ goto end;
+
+ /* wait for burstcount */
+ if (chip->vendor.irq) {
+ rc = wait_for_serirq_timeout(chip, (check_locality
+ (chip) >= 0),
+ chip->vendor.timeout_a);
+ if (rc > 0)
+ return chip->vendor.locality;
+ } else {
+ stop = jiffies + chip->vendor.timeout_a;
+ do {
+ if (check_locality(chip) >= 0)
+ return chip->vendor.locality;
+ msleep(TPM_TIMEOUT);
+ } while (time_before(jiffies, stop));
+ }
+end:
+ return -EACCES;
+} /* request_locality() */
+
+/*
+ * release_locality release the active locality
+ * @param: chip, the tpm chip description.
+ */
+static void release_locality(struct tpm_chip *chip)
+{
+ struct spi_device *client;
+ u8 data;
+
+ FUNC_ENTER();
+
+ client = (struct spi_device *) chip->vendor.iobase;
+ data = TPM_ACCESS_ACTIVE_LOCALITY;
+ SPI_WRITE_DATA(chip, TPM_ACCESS, &data, 1);
+} /* release_locality()*/
+
+/*
+ * get_burstcount return the burstcount address 0x19 0x1A
+ * @param: chip, the chip description
+ * return: the burstcount.
+ */
+static int get_burstcount(struct tpm_chip *chip)
+{
+ unsigned long stop;
+ u32 burstcnt, status;
+ u8 tpm_reg, temp;
+
+ FUNC_ENTER();
+
+ /* wait for burstcount */
+ /* which timeout value, spec has 2 answers (c & d) */
+ stop = jiffies + chip->vendor.timeout_d;
+ do {
+ tpm_reg = TPM_STS + 1;
+ status = SPI_READ_DATA(chip, tpm_reg, &temp, 1);
+ if (status < 0)
+ goto end;
+
+ tpm_reg = tpm_reg + 1;
+ burstcnt = temp;
+ status = SPI_READ_DATA(chip, tpm_reg, &temp, 1);
+ if (status < 0)
+ goto end;
+
+ burstcnt |= temp << 8;
+ if (burstcnt)
+ return burstcnt;
+ msleep(TPM_TIMEOUT);
+ } while (time_before(jiffies, stop));
+
+end:
+ return -EBUSY;
+} /* get_burstcount() */
+
+/*
+ * wait_for_stat wait for a TPM_STS value
+ * @param: chip, the tpm chip description
+ * @param: mask, the value mask to wait
+ * @param: timeout, the timeout
+ * @param: queue, the wait queue.
+ * @return: the tpm status, 0 if success, -ETIME if timeout is reached.
+ */
+static int wait_for_stat(struct tpm_chip *chip, u8 mask, unsigned long timeout,
+ wait_queue_head_t *queue)
+{
+ unsigned long stop;
+ long rc;
+ u8 status;
+
+ FUNC_ENTER();
+
+ /* check current status */
+ status = tpm_stm_spi_status(chip);
+ if (!chip->vendor.irq && (status & mask) == mask)
+ return 0;
+
+ if (chip->vendor.irq) {
+ rc = wait_for_serirq_timeout(chip, ((tpm_stm_spi_status
+ (chip) & mask) ==
+ mask), timeout);
+ if (rc > 0)
+ return 0;
+ } else {
+ stop = jiffies + timeout;
+ do {
+ msleep(TPM_TIMEOUT);
+ status = tpm_stm_spi_status(chip);
+ if ((status & mask) == mask)
+ return 0;
+ } while (time_before(jiffies, stop));
+ }
+ return -ETIME;
+} /* wait_for_stat() */
+
+/*
+ * recv_data receive data
+ * @param: chip, the tpm chip description
+ * @param: buf, the buffer where the data are received
+ * @param: count, the number of data to receive
+ * @return: the tpm status, 0 if success, -ETIME if timeout is reached.
+ */
+static int recv_data(struct tpm_chip *chip, u8 *buf, size_t count)
+{
+ u32 size = 0, burstcnt, status, len;
+ struct spi_device *client;
+
+ FUNC_ENTER();
+
+ client = (struct spi_device *) chip->vendor.iobase;
+
+ while (size < count &&
+ wait_for_stat(chip,
+ TPM_STS_DATA_AVAIL | TPM_STS_VALID,
+ chip->vendor.timeout_c,
+ &chip->vendor.read_queue)
+ == 0) {
+ burstcnt = get_burstcount(chip);
+ len = min_t(int, burstcnt, count - size);
+ status = SPI_READ_DATA(chip, TPM_DATA_FIFO, buf + size, len);
+ if (status < 0)
+ return status;
+
+
+ size += len;
+ }
+ return size;
+}
+
+/*
+ * tpm_ioserirq_handler the serirq irq handler
+ * @param: irq, the tpm chip description
+ * @param: dev_id, the description of the chip
+ * @return: the status of the handler.
+ */
+static irqreturn_t tpm_ioserirq_handler(int irq, void *dev_id)
+{
+ struct tpm_chip *chip = dev_id;
+ struct spi_device *client;
+ struct st33zp24_platform_data *pin_infos;
+
+ disable_irq_nosync(irq);
+ FUNC_ENTER();
+
+ client = (struct spi_device *) chip->vendor.iobase;
+ pin_infos = client->dev.platform_data;
+
+ complete(&pin_infos->irq_detection);
+ return IRQ_HANDLED;
+} /* tpm_ioserirq_handler() */
+
+/*
+ * tpm_stm_spi_send send TPM commands through the SPI bus.
+ * @param: chip, the tpm chip description
+ * @param: buf, the tpm command buffer
+ * @param: len, the tpm command size
+ * @return: In case of success the number of bytes sent.
+ * In other case, a < 0 value describing the issue.
+ */
+static int tpm_stm_spi_send(struct tpm_chip *chip, unsigned char *buf,
+ size_t len)
+{
+ u32 ret = 0, ordinal,
+ status, burstcnt = 0, i, size = 0;
+ u8 data;
+
+ struct spi_device *client;
+ struct st33zp24_platform_data *pin_infos;
+
+ FUNC_ENTER();
+
+ if (chip == NULL)
+ return -EBUSY;
+ if (len < TPM_HEADER_SIZE)
+ return -EBUSY;
+
+ client = (struct spi_device *)chip->vendor.iobase;
+ pin_infos = client->dev.platform_data;
+
+ ordinal = be32_to_cpu(*((__be32 *) (buf + 6)));
+
+ ret = request_locality(chip);
+ if (ret < 0)
+ return ret;
+
+ status = tpm_stm_spi_status(chip);
+ if ((status & TPM_STS_COMMAND_READY) == 0) {
+ tpm_stm_spi_cancel(chip);
+ if (wait_for_stat
+ (chip, TPM_STS_COMMAND_READY, chip->vendor.timeout_b,
+ &chip->vendor.int_queue) < 0) {
+ ret = -ETIME;
+ goto out_err;
+ }
+ }
+
+ for (i = 0 ; i < len - 1 ;) {
+ burstcnt = get_burstcount(chip);
+ size = min_t(int, len - i - 1, burstcnt);
+ ret = SPI_WRITE_DATA(chip, TPM_DATA_FIFO, buf, size);
+ if (ret < 0)
+ goto out_err;
+ i += size;
+ }
+
+ status = tpm_stm_spi_status(chip);
+ if ((status & TPM_STS_DATA_EXPECT) == 0) {
+ ret = -EIO;
+ goto out_err;
+ }
+
+ /* write last byte */
+ SPI_WRITE_DATA(chip, TPM_DATA_FIFO, buf + len - 1, 1);
+
+ status = tpm_stm_spi_status(chip);
+ if ((status & TPM_STS_DATA_EXPECT) != 0) {
+ ret = -EIO;
+ goto out_err;
+ }
+
+ /* go and do it */
+ data = TPM_STS_GO;
+ ret = SPI_WRITE_DATA(chip, TPM_STS, &data, 1);
+ if (ret < 0)
+ goto out_err;
+
+ return len;
+out_err:
+ tpm_stm_spi_cancel(chip);
+ release_locality(chip);
+ return ret;
+}
+
+/*
+ * tpm_stm_spi_recv received TPM response through the SPI bus.
+ * @param: chip, the tpm chip description
+ * @param: buf, the tpm command buffer
+ * @param: len, the tpm command size
+* @return: In case of success the number of bytes received.
+ * In other case, a < 0 value describing the issue.
+ */
+static int tpm_stm_spi_recv(struct tpm_chip *chip, unsigned char *buf,
+ size_t count)
+{
+ int size = 0;
+ int expected;
+
+ struct spi_device *client;
+ struct st33zp24_platform_data *pin_infos;
+
+
+ FUNC_ENTER();
+
+ client = (struct spi_device *)chip->vendor.iobase;
+ pin_infos = client->dev.platform_data;
+
+
+ if (chip == NULL)
+ return -EBUSY;
+ if (count < TPM_HEADER_SIZE) {
+ size = -EIO;
+ goto out;
+ }
+
+ size = recv_data(chip, buf, TPM_HEADER_SIZE);
+
+ /* read first 10 bytes, including tag, paramsize, and result */
+ if (size < TPM_HEADER_SIZE) {
+ dev_err(chip->dev, "Unable to read header\n");
+ goto out;
+ }
+
+ expected = be32_to_cpu(*(__be32 *) (buf + 2));
+ if (expected > count) {
+ size = -EIO;
+ goto out;
+ }
+
+ size += recv_data(chip, &buf[TPM_HEADER_SIZE],
+ expected - TPM_HEADER_SIZE);
+ if (size < expected) {
+ dev_err(chip->dev, "Unable to read remainder of result\n");
+ size = -ETIME;
+ goto out;
+ }
+
+out:
+ chip->vendor.cancel(chip);
+ release_locality(chip);
+ return size;
+}
+
+
+static const struct file_operations tpm_st33_spi_fops = {
+ .owner = THIS_MODULE,
+ .llseek = no_llseek,
+ .read = tpm_read,
+ .write = tpm_write,
+ .open = tpm_open,
+ .release = tpm_release,
+};
+
+static DEVICE_ATTR(pubek, S_IRUGO, tpm_show_pubek, NULL);
+static DEVICE_ATTR(pcrs, S_IRUGO, tpm_show_pcrs, NULL);
+static DEVICE_ATTR(enabled, S_IRUGO, tpm_show_enabled, NULL);
+static DEVICE_ATTR(active, S_IRUGO, tpm_show_active, NULL);
+static DEVICE_ATTR(owned, S_IRUGO, tpm_show_owned, NULL);
+static DEVICE_ATTR(temp_deactivated, S_IRUGO, tpm_show_temp_deactivated, NULL);
+static DEVICE_ATTR(caps, S_IRUGO, tpm_show_caps_1_2, NULL);
+static DEVICE_ATTR(cancel, S_IWUSR | S_IWGRP, NULL, tpm_store_cancel);
+
+static struct attribute *stm_tpm_attrs[] = {
+ &dev_attr_pubek.attr,
+ &dev_attr_pcrs.attr,
+ &dev_attr_enabled.attr,
+ &dev_attr_active.attr,
+ &dev_attr_owned.attr,
+ &dev_attr_temp_deactivated.attr,
+ &dev_attr_caps.attr,
+ &dev_attr_cancel.attr, NULL,
+};
+
+static struct attribute_group stm_tpm_attr_grp = {
+ .attrs = stm_tpm_attrs
+};
+
+static struct tpm_vendor_specific st_spi_tpm = {
+ .send = tpm_stm_spi_send,
+ .recv = tpm_stm_spi_recv,
+ .cancel = tpm_stm_spi_cancel,
+ .status = tpm_stm_spi_status,
+ .attr_group = &stm_tpm_attr_grp,
+ .miscdev = {.fops = &tpm_st33_spi_fops,},
+};
+
+static int evaluate_latency(struct tpm_chip *chip)
+{
+ int latency = 0;
+ struct spi_device *dev = (struct spi_device *) chip->vendor.iobase;
+ struct st33zp24_platform_data *platform_data = dev->dev.platform_data;
+ int status = 0;
+ u8 data;
+
+ for (; status == 0x00 && latency < MAX_SPI_LATENCY ; latency++) {
+ platform_data->latency = latency;
+ status = SPI_READ_DATA(chip, TPM_INTF_CAPABILITY, &data, 1);
+ }
+ return latency - 1;
+} /* evaluate_latency() */
+
+static int interrupts;
+module_param(interrupts, int, 0444);
+MODULE_PARM_DESC(interrupts, "Enable interrupts");
+
+static int power_mgt = 1;
+module_param(power_mgt, int, 0444);
+MODULE_PARM_DESC(power_mgt, "Power Management");
+
+/*
+ * tpm_st33_spi_probe initialize the TPM device
+ * @param: client, the spi_device drescription (TPM SPI description).
+ * @param: id, the spi_device_id struct.
+ * @return: 0 in case of success.
+ * -1 in other case.
+ */
+static int
+tpm_st33_spi_probe(struct spi_device *dev)
+{
+ u32 err;
+ u8 intmask;
+ struct tpm_chip *chip;
+ struct st33zp24_platform_data *platform_data;
+
+ FUNC_ENTER();
+
+ err = 0;
+
+ /* Check SPI platform functionnalities */
+ if (dev == NULL) {
+ pr_info("dev is NULL. exiting.\n");
+ err = -ENODEV;
+ goto end;
+ }
+
+ chip = tpm_register_hardware(&dev->dev, &st_spi_tpm);
+ if (!chip) {
+ err = -ENODEV;
+ goto end;
+ }
+
+ /* Allocation of SPI buffers MISO and MOSI */
+ /* Size is as follow: */
+ /* Request burstcount value = 0x800 = 2048 */
+ /* + */
+ /* Response burstcount value = 0x400 = 1024 */
+ /* + */
+ /* At least: */
+ /* 1 byte for direction/locality */
+ /* 1 byte tpm tis register */
+ /* 2 bytes spi data length (for request only) */
+ /* 2 latency bytes */
+ /* 1 status byte */
+ /* = 2048 + 1024 + 7 */
+ /* We reserved 2048 + 1024 + 20 in case latency byte */
+ /* change */
+ platform_data = dev->dev.platform_data;
+ platform_data->tpm_spi_buffer[0] =
+ kmalloc((TPM_BUFSIZE + (TPM_BUFSIZE / 2) +
+ TPM_DIGEST_SIZE) * sizeof(u8), GFP_KERNEL);
+ if (platform_data->tpm_spi_buffer[0] == NULL) {
+ err = -ENOMEM;
+ goto _tpm_clean_answer;
+ }
+ platform_data->tpm_spi_buffer[1] =
+ kmalloc((TPM_BUFSIZE + (TPM_BUFSIZE / 2) +
+ TPM_DIGEST_SIZE) * sizeof(u8) , GFP_KERNEL);
+ if (platform_data->tpm_spi_buffer[1] == NULL) {
+ err = -ENOMEM;
+ goto _tpm_clean_response;
+ }
+
+ chip->vendor.iobase = dev;
+
+ /* Default timeouts */
+ chip->vendor.timeout_a = msecs_to_jiffies(TIS_SHORT_TIMEOUT);
+ chip->vendor.timeout_b = msecs_to_jiffies(TIS_LONG_TIMEOUT);
+ chip->vendor.timeout_c = msecs_to_jiffies(TIS_SHORT_TIMEOUT);
+ chip->vendor.timeout_d = msecs_to_jiffies(TIS_SHORT_TIMEOUT);
+ chip->vendor.locality = LOCALITY0;
+
+ if (power_mgt) {
+ err = gpio_request(platform_data->io_lpcpd, "TPM IO_LPCPD");
+ if (err)
+ goto _gpio_init1;
+ gpio_set_value(platform_data->io_lpcpd, 1);
+ }
+
+ platform_data->latency = evaluate_latency(chip);
+ if (platform_data->latency <= 0x00) {
+ err = -ENODEV;
+ goto _gpio_init1;
+ }
+
+ /* Enable interrupt */
+ /* Register GPIO pin through generic Linux GPIO API */
+ if (interrupts) {
+ init_completion(&platform_data->irq_detection);
+ if (request_locality(chip) != LOCALITY0) {
+ err = -ENODEV;
+ goto _tpm_clean_response;
+ }
+ err = gpio_request(platform_data->io_serirq, "TPM IO_SERIRQ");
+ if (err)
+ goto _gpio_init2;
+
+ /* Clear all existing */
+ clear_interruption(chip);
+ err = request_irq(gpio_to_irq(platform_data->io_serirq),
+ &tpm_ioserirq_handler,
+ IRQF_TRIGGER_HIGH | IRQF_SHARED,
+ "TPM SERIRQ management", chip);
+ if (err < 0) {
+
+ pr_info("TPM SERIRQ signals %d not available\n",
+ gpio_to_irq(platform_data->io_serirq));
+ goto _irq_set;
+ }
+ err = SPI_READ_DATA(chip, TPM_INT_ENABLE, &intmask, 1);
+ if (err < 0)
+ goto _irq_set;
+
+ intmask |= TPM_INTF_CMD_READY_INT
+ | TPM_INTF_FIFO_AVALAIBLE_INT
+ | TPM_INTF_WAKE_UP_READY_INT
+ | TPM_INTF_LOC4SOFTRELEASE_INT
+ | TPM_INTF_LOCALITY_CHANGE_INT
+ | TPM_INTF_STS_VALID_INT
+ | TPM_INTF_DATA_AVAIL_INT;
+
+ err = SPI_WRITE_DATA(chip, TPM_INT_ENABLE, &intmask, 1);
+ if (err < 0)
+ goto _irq_set;
+
+ intmask = TPM_GLOBAL_INT_ENABLE;
+ err = SPI_WRITE_DATA(chip, TPM_INT_ENABLE + 3, &intmask, 1);
+ if (err < 0)
+ goto _irq_set;
+
+ err = SPI_READ_DATA(chip, TPM_INT_STATUS, &intmask, 1);
+ if (err < 0)
+ goto _irq_set;
+
+ chip->vendor.irq = interrupts;
+
+ tpm_gen_interrupt(chip);
+ }
+
+ tpm_get_timeouts(chip);
+
+ /* attach chip datas to client */
+ spi_set_drvdata(dev, chip);
+ platform_data->bChipF = false;
+
+ pr_info("TPM SPI Initialized\n");
+ return 0;
+_irq_set:
+ free_irq(gpio_to_irq(platform_data->io_serirq), chip);
+_gpio_init2:
+ if (platform_data && interrupts)
+ gpio_free(platform_data->io_serirq);
+_gpio_init1:
+ if (platform_data && power_mgt)
+ gpio_free(platform_data->io_lpcpd);
+_tpm_clean_response:
+ tpm_remove_hardware(chip->dev);
+ if (platform_data->tpm_spi_buffer[1] != NULL) {
+ kfree(platform_data->tpm_spi_buffer[1]);
+ platform_data->tpm_spi_buffer[1] = NULL;
+ }
+_tpm_clean_answer:
+ if (platform_data->tpm_spi_buffer[0] != NULL) {
+ kfree(platform_data->tpm_spi_buffer[0]);
+ platform_data->tpm_spi_buffer[0] = NULL;
+ }
+
+ platform_data->bChipF = true;
+end:
+ pr_info("TPM SPI initialisation fail\n");
+ return err;
+}
+
+/*
+ * tpm_st33_spi_remove remove the TPM device
+ * @param: client, the spi_device drescription (TPM SPI description).
+ clear_bit(0, &chip->is_open);
+ * @return: 0 in case of success.
+ */
+static int tpm_st33_spi_remove(struct spi_device *client)
+{
+ struct tpm_chip *chip = (struct tpm_chip *)spi_get_drvdata(client);
+ struct st33zp24_platform_data *pin_infos =
+ ((struct spi_device *) chip->vendor.iobase)->dev.platform_data;
+
+ FUNC_ENTER();
+
+ if (pin_infos != NULL) {
+ gpio_free(pin_infos->io_lpcpd);
+
+ /* Check if chip has been previously clean */
+ if (pin_infos->bChipF != true)
+ tpm_remove_hardware(chip->dev);
+ if (pin_infos->tpm_spi_buffer[1] != NULL) {
+ kfree(pin_infos->tpm_spi_buffer[1]);
+ pin_infos->tpm_spi_buffer[1] = NULL;
+ }
+ if (pin_infos->tpm_spi_buffer[0] != NULL) {
+ kfree(pin_infos->tpm_spi_buffer[0]);
+ pin_infos->tpm_spi_buffer[0] = NULL;
+ }
+ }
+
+ return 0;
+}
+
+/*
+ * tpm_st33_spi_pm_suspend suspend the TPM device
+ * Added: Work around when suspend and no tpm application is running, suspend
+ * may fail because chip->data_buffer is not set (only set in tpm_open in Linux
+ * TPM core)
+ * @param: client, the spi_device drescription (TPM SPI description).
+ * @param: mesg, the power management message.
+ * @return: 0 in case of success.
+ */
+static int tpm_st33_spi_pm_suspend(struct spi_device *client,
+ pm_message_t mesg)
+{
+ struct tpm_chip *chip =
+ (struct tpm_chip *)spi_get_drvdata(client);
+ struct st33zp24_platform_data *pin_infos =
+ ((struct spi_device *)chip->vendor.iobase)->dev.platform_data;
+ int ret = 0;
+
+ if (power_mgt)
+ gpio_set_value(pin_infos->io_lpcpd, 0);
+ else {
+ if (chip->data_buffer == NULL)
+ chip->data_buffer = pin_infos->tpm_spi_buffer[0];
+ ret = tpm_pm_suspend(&client->dev);
+ }
+ return ret;
+} /* tpm_st33_spi_suspend() */
+
+/*
+ * tpm_st33_spi_pm_resume resume the TPM device
+ * @param: spi, the spi_device drescription (TPM SPI description).
+ * @return: 0 in case of success.
+ */
+static int tpm_st33_spi_pm_resume(struct spi_device *spi)
+{
+ struct tpm_chip *chip =
+ (struct tpm_chip *)spi_get_drvdata(spi);
+ struct st33zp24_platform_data *pin_infos =
+ ((struct spi_device *)chip->vendor.iobase)->dev.platform_data;
+
+ int ret = 0;
+ if (power_mgt) {
+ gpio_set_value(pin_infos->io_lpcpd, 1);
+ ret = wait_for_serirq_timeout(chip,
+ (chip->vendor.status(chip) &&
+ TPM_STS_VALID) == TPM_STS_VALID,
+ chip->vendor.timeout_b);
+ } else {
+ if (chip->data_buffer == NULL)
+ chip->data_buffer = pin_infos->tpm_spi_buffer[0];
+ ret = tpm_pm_resume(&spi->dev);
+ if (!ret)
+ tpm_do_selftest(chip);
+ }
+ return ret;
+} /* tpm_st33_spi_pm_resume() */
+
+static struct spi_driver tpm_st33_spi_driver = {
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = TPM_ST33_SPI,
+ },
+ .probe = tpm_st33_spi_probe,
+ .remove = tpm_st33_spi_remove,
+ .resume = tpm_st33_spi_pm_resume,
+ .suspend = tpm_st33_spi_pm_suspend,
+};
+
+/*
+ * tpm_st33_spi_init initialize driver
+ * @return: 0 if successful, else non zero value.
+ */
+static int __init tpm_st33_spi_init(void)
+{
+ FUNC_ENTER();
+ return spi_register_driver(&tpm_st33_spi_driver);
+}
+
+/*
+ * tpm_st33_spi_exit The kernel calls this function during unloading the
+ * module or during shut down process
+ */
+static void __exit tpm_st33_spi_exit(void)
+{
+ FUNC_ENTER();
+ spi_unregister_driver(&tpm_st33_spi_driver);
+}
+
+module_init(tpm_st33_spi_init);
+module_exit(tpm_st33_spi_exit);
+
+MODULE_AUTHOR("Christophe Ricard ([email protected])");
+MODULE_DESCRIPTION("STM TPM SPI ST33 Driver");
+MODULE_VERSION("1.2.0");
+MODULE_LICENSE("GPL");
diff --git a/drivers/char/tpm/tpm_spi_stm_st33.h b/drivers/char/tpm/tpm_spi_stm_st33.h
new file mode 100644
index 0000000..42bae6f
--- /dev/null
+++ b/drivers/char/tpm/tpm_spi_stm_st33.h
@@ -0,0 +1,75 @@
+/*
+ * STMicroelectronics TPM SPI Linux driver for TPM ST33NP18
+ * Copyright (C) 2009, 2010 STMicroelectronics
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ * STMicroelectronics version 1.2.0, Copyright (C) 2010
+ * STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
+ * This is free software, and you are welcome to redistribute it
+ * under certain conditions.
+ *
+ * @Author: Christophe RICARD [email protected]
+ *
+ * @File: tpm_spi_stm_st33.h
+ *
+ * @Date: 09/15/2010
+ */
+#ifndef __STM_ST33_TPM_SPI_MAIN_H__
+#define __STM_ST33_TPM_SPI_MAIN_H__
+
+#include <linux/pci.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/fs.h>
+#include <linux/miscdevice.h>
+
+#define MINOR_NUM_SPI 224
+
+#define TPM_ACCESS (0x0)
+#define TPM_STS (0x18)
+#define TPM_HASH_END (0x20)
+#define TPM_DATA_FIFO (0x24)
+#define TPM_HASH_DATA (0x24)
+#define TPM_HASH_START (0x28)
+#define TPM_INTF_CAPABILITY (0x14)
+#define TPM_INT_STATUS (0x10)
+#define TPM_INT_ENABLE (0x08)
+
+#define TPM_DUMMY_BYTE 0x00
+#define TPM_WRITE_DIRECTION 0x80
+#define TPM_HEADER_SIZE 10
+#define TPM_BUFSIZE 2048
+
+/* ioctl commands */
+#define TPMIOC_CANCEL _IO('T', 0x00)
+#define TPMIOC_TRANSMIT _IO('T', 0x01)
+#define TPMIOC_HASH _IO('T', 0x02)
+#define TPMIOC_CHANGELOCALITY _IO('T', 0x03)
+
+#define LOCALITY0 0
+#define LOCALITY4 4
+
+#define TPM_ST_SPI_OK 0x5A
+
+
+#define MAX_SPI_LATENCY 15
+
+struct st_tpm_hash_t {
+ int size;
+ u8 *data;
+};
+
+#endif /* __STM_ST33_TPM_SPI_MAIN_H__ */
diff --git a/include/linux/spi/tpm_spi_stm_st33.h b/include/linux/spi/tpm_spi_stm_st33.h
new file mode 100644
index 0000000..c233ff6
--- /dev/null
+++ b/include/linux/spi/tpm_spi_stm_st33.h
@@ -0,0 +1,46 @@
+/*
+* STMicroelectronics TPM SPI Linux driver for TPM ST33NP18
+* Copyright (C) 2009, 2010 STMicroelectronics
+* Christophe RICARD [email protected]
+* This program is free software; you can redistribute it and/or modify
+* it under the terms of the GNU General Public License as published by
+* the Free Software Foundation; either version 2 of the License, or
+* (at your option) any later version.
+*
+* This program is distributed in the hope that it will be useful,
+* but WITHOUT ANY WARRANTY; without even the implied warranty of
+* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+* GNU General Public License for more details.
+*
+* You should have received a copy of the GNU General Public License along
+* with this program; if not, write to the Free Software Foundation, Inc.,
+* 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+*
+* STMicroelectronics version 1.2.0, Copyright (C) 2010
+* STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
+* This is free software, and you are welcome to redistribute it
+* under certain conditions.
+*
+* @File: tpm_spi_stm_st33.h
+*
+* @Date: 06/15/2008
+*/
+#ifndef __STM_ST33_TPM_SPI_H__
+#define __STM_ST33_TPM_SPI_H__
+
+#include <linux/spi/spi.h>
+
+#define TPM_ST33_SPI "st33zp24_spi"
+
+#ifndef __STM_ST33_TPM_SPI_H__
+struct st33zp24_platform_data {
+ int io_serirq;
+ int io_lpcpd;
+ int latency;
+ bool bChipF;
+ u8 *tpm_spi_buffer[2]; /* 0 Request 1 Response */
+ struct completion irq_detection;
+};
+#endif
+
+#endif /* __STM_ST33_TPM_SPI_H__ */
--
1.7.1
On Mon, Mar 25, 2013 at 10:08 AM, Matthias Leblanc
<[email protected]> wrote:
> From: admin01 <admin01@admin01-desktop.(none)>
>
> * STMicroelectronics version 1.2.0, Copyright (C) 2010
> * STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
> * This is free software, and you are welcome to redistribute it
> * under certain conditions.
>
> This is the driver for TPM chip from ST Microelectronics.
>
> If you have a TPM security chip from STMicroelectronics working with
> an I2C/SPI, in menuconfig or .config choose the tpm driver on
> device --> tpm and activate the protocol of your choice before compiling
> the kernel.
> The driver will be accessible from within Linux.
>
> Tested on linux x86/x64 and beagleboard REV B & XM REV C
>
> Signed-off-by: admin01 <admin01@admin01-desktop.(none)>
Who is admin01 and why is he signing off your patches? :-)
Kent
> ---
> arch/arm/mach-omap2/board-omap3beagle.c | 40 ++
> drivers/char/tpm/Kconfig | 10 +
> drivers/char/tpm/Makefile | 1 +
> drivers/char/tpm/tpm_spi_stm_st33.c | 1116 +++++++++++++++++++++++++++++++
> drivers/char/tpm/tpm_spi_stm_st33.h | 75 ++
> include/linux/spi/tpm_spi_stm_st33.h | 46 ++
> 6 files changed, 1287 insertions(+), 0 deletions(-)
> create mode 100644 drivers/char/tpm/tpm_spi_stm_st33.c
> create mode 100644 drivers/char/tpm/tpm_spi_stm_st33.h
> create mode 100644 include/linux/spi/tpm_spi_stm_st33.h
>
> diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
> index c3558f9..72e6513 100644
> --- a/arch/arm/mach-omap2/board-omap3beagle.c
> +++ b/arch/arm/mach-omap2/board-omap3beagle.c
> @@ -46,6 +46,11 @@
> #include <video/omap-panel-tfp410.h>
> #include <linux/platform_data/mtd-nand-omap2.h>
>
> +#ifdef CONFIG_TCG_ST33_SPI
> +#include <linux/spi/tpm_spi_stm_st33.h>
> +#include <linux/spi/spi.h>
> +#endif /* CONFIG_TCG_ST33_SPI */
> +
> #include "common.h"
> #include "omap_device.h"
> #include "gpmc.h"
> @@ -375,6 +380,26 @@ static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
> },
> };
>
> +#if defined CONFIG_TCG_ST33_I2C || defined CONFIG_TCG_ST33_SPI
> +static struct st33zp24_platform_data tpm_data = {
> + .io_serirq = 136,
> + .io_lpcpd = 143,
> +};
> +#endif
> +
> +#ifdef CONFIG_TCG_ST33_SPI
> +static struct spi_board_info tpm_st33_spi_board_info[] = {
> + {
> + .modalias = TPM_ST33_SPI,
> + .max_speed_hz = 10000000,
> + .bus_num = 4,
> + .chip_select = 0,
> + .mode = SPI_MODE_0,
> + .platform_data = &tpm_data,
> + },
> +};
> +#endif
> +
> static int __init omap3_beagle_i2c_init(void)
> {
> omap3_pmic_get_config(&beagle_twldata,
> @@ -556,6 +581,20 @@ static void __init omap3_beagle_init(void)
> omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
> omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
>
> + #if defined CONFIG_TCG_ST33_I2C || defined CONFIG_TCG_ST33_SPI
> + omap_mux_init_gpio(tpm_data.io_serirq, OMAP_PIN_INPUT);
> + omap_mux_init_gpio(tpm_data.io_lpcpd, OMAP_PIN_OUTPUT);
> + #endif
> +
> + #ifdef CONFIG_TCG_ST33_SPI
> + omap_mux_init_signal("mcspi4_clk", OMAP_PIN_INPUT);
> + omap_mux_init_signal("mcspi4_cs0", OMAP_PIN_OUTPUT);
> + omap_mux_init_signal("mcspi4_simo", OMAP_PIN_OUTPUT);
> + omap_mux_init_signal("mcspi4_somi", OMAP_PIN_INPUT);
> +
> + spi_register_board_info(tpm_st33_spi_board_info,
> + ARRAY_SIZE(tpm_st33_spi_board_info));
> + #endif
> +
> pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup));
> }
>
> diff --git a/drivers/char/tpm/Kconfig b/drivers/char/tpm/Kconfig
> index dbfd564..2fc1254 100644
> --- a/drivers/char/tpm/Kconfig
> +++ b/drivers/char/tpm/Kconfig
> @@ -91,4 +91,14 @@ config TCG_ST33_I2C
> To compile this driver as a module, choose M here; the module will be
> called tpm_stm_st33_i2c.
>
> +config TCG_ST33_SPI
> + tristate "STMicroelectronics ST33 SPI"
> + depends on SPI
> + depends on GPIOLIB
> + ---help---
> + If you have a TPM security chip from STMicroelectronics working with
> + an SPI bus say Yes and it will be accessible from within Linux.
> + To compile this driver as a module, choose M here; the module will be
> + called tpm_stm_st33_spi.
> +
> endif # TCG_TPM
> diff --git a/drivers/char/tpm/Makefile b/drivers/char/tpm/Makefile
> index a3736c9..a1db3dd 100644
> --- a/drivers/char/tpm/Makefile
> +++ b/drivers/char/tpm/Makefile
> @@ -18,3 +18,4 @@ obj-$(CONFIG_TCG_ATMEL) += tpm_atmel.o
> obj-$(CONFIG_TCG_INFINEON) += tpm_infineon.o
> obj-$(CONFIG_TCG_IBMVTPM) += tpm_ibmvtpm.o
> obj-$(CONFIG_TCG_ST33_I2C) += tpm_i2c_stm_st33.o
> +obj-$(CONFIG_TCG_ST33_SPI) += tpm_spi_stm_st33.o
> diff --git a/drivers/char/tpm/tpm_spi_stm_st33.c b/drivers/char/tpm/tpm_spi_stm_st33.c
> new file mode 100644
> index 0000000..a47c647
> --- /dev/null
> +++ b/drivers/char/tpm/tpm_spi_stm_st33.c
> @@ -0,0 +1,1116 @@
> +/*
> + * STMicroelectronics TPM SPI Linux driver for TPM ST33ZP24
> + * Copyright (C) 2009, 2010 STMicroelectronics
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License along
> + * with this program; if not, write to the Free Software Foundation, Inc.,
> + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
> + *
> + * STMicroelectronics version 1.2.0, Copyright (C) 2010
> + * STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
> + * This is free software, and you are welcome to redistribute it
> + * under certain conditions.
> + *
> + * @Author: Christophe RICARD [email protected]
> + *
> + * @File: tpm_stm_st33_spi.c
> + *
> + * @Synopsis:
> + * 09/15/2010: First shot driver tpm_tis driver for lpc is
> + * used as model.
> + */
> +
> +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
> +
> +#include <linux/module.h>
> +#include <linux/kernel.h>
> +#include <linux/delay.h>
> +#include <linux/init.h>
> +#include <linux/spi/spi.h>
> +#include <linux/wait.h>
> +#include <linux/string.h>
> +#include <linux/interrupt.h>
> +#include <linux/spinlock.h>
> +#include <linux/sysfs.h>
> +#include <linux/gpio.h>
> +#include <linux/sched.h>
> +#include <linux/uaccess.h>
> +#include <linux/io.h>
> +#include <linux/slab.h>
> +#include <linux/sched.h>
> +
> +#include <linux/spi/tpm_spi_stm_st33.h>
> +
> +#include "tpm.h"
> +
> +#include "tpm_spi_stm_st33.h"
> +
> +#ifdef DEBUG
> +#define FUNC_ENTER() pr_info("%s\n", __func__)
> +#else
> +#define FUNC_ENTER() do {} while (0)
> +#endif
> +
> +enum stm33zp24_access {
> + TPM_ACCESS_VALID = 0x80,
> + TPM_ACCESS_ACTIVE_LOCALITY = 0x20,
> + TPM_ACCESS_REQUEST_PENDING = 0x04,
> + TPM_ACCESS_REQUEST_USE = 0x02,
> +};
> +
> +enum stm33zp24_status {
> + TPM_STS_VALID = 0x80,
> + TPM_STS_COMMAND_READY = 0x40,
> + TPM_STS_GO = 0x20,
> + TPM_STS_DATA_AVAIL = 0x10,
> + TPM_STS_DATA_EXPECT = 0x08,
> +};
> +
> +enum stm33zp24_int_flags {
> + TPM_GLOBAL_INT_ENABLE = 0x80,
> + TPM_INTF_CMD_READY_INT = 0x080,
> + TPM_INTF_FIFO_AVALAIBLE_INT = 0x040,
> + TPM_INTF_WAKE_UP_READY_INT = 0x020,
> + TPM_INTF_LOC4SOFTRELEASE_INT = 0x008,
> + TPM_INTF_LOCALITY_CHANGE_INT = 0x004,
> + TPM_INTF_STS_VALID_INT = 0x002,
> + TPM_INTF_DATA_AVAIL_INT = 0x001,
> +};
> +
> +enum tis_defaults {
> + TIS_SHORT_TIMEOUT = 750, /* ms */
> + TIS_LONG_TIMEOUT = 2000, /* 2 sec */
> +};
> +
> +/*
> + * write8_reg
> + * Send byte to the TIS register according to the ST33ZP24 SPI protocol.
> + * @param: tpm, the chip description
> + * @param: tpm_register, the tpm tis register where the data should be written
> + * @param: tpm_data, the tpm_data to write inside the tpm_register
> + * @param: tpm_size, The length of the data
> + * @return: number of byte written successfully: should be one if success.
> + */
> +static int write8_reg(struct tpm_chip *tpm, u8 tpm_register,
> + u8 *tpm_data, u16 tpm_size)
> +{
> + /* u8 LOC+DIR u8 ADD u16 LENGHT u8* data */
> + /* u8 LATENCY u8 LATENCY */
> +
> + u8 data;
> + int i = 0, j;
> + int value = 0;
> + struct spi_device *dev = (struct spi_device *) tpm->vendor.iobase;
> + struct st33zp24_platform_data *platform_data = dev->dev.platform_data;
> + u8 *data_buffer = platform_data->tpm_spi_buffer[0];
> + struct spi_transfer xfer = {
> + .tx_buf = data_buffer,
> + .rx_buf = platform_data->tpm_spi_buffer[1],
> + };
> + struct spi_message msg;
> + u8 latency = platform_data->latency + tpm_size + 1;
> +
> +
> + FUNC_ENTER();
> + /* Pre-Header */
> +
> + data = TPM_WRITE_DIRECTION | tpm->vendor.locality;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> + data = tpm_register;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> +
> + if (tpm_size > 0 &&
> + (tpm_register == TPM_DATA_FIFO ||
> + tpm_register == TPM_HASH_DATA)) {
> + data = tpm_size >> 8 & 0x00ff;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> + data = tpm_size & 0x00ff;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> + latency -= 2;
> + }
> +
> + memcpy(data_buffer + i, tpm_data, tpm_size);
> + i += tpm_size;
> +
> + for (j = 0 ; j < platform_data->latency + 1; j++) {
> + data = TPM_DUMMY_BYTE;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> + }
> + xfer.len = i;
> + spi_message_init(&msg);
> + spi_message_add_tail(&xfer, &msg);
> + value = spi_sync(dev, &msg);
> +
> + if (value == 0) {
> + j = i - 1 - j;
> + for (; j < i && ((u8 *) xfer.rx_buf)[j] == 0; j++)
> + ;
> +
> + if (((u8 *) xfer.rx_buf)[j] != 0)
> + value = ((u8 *) xfer.rx_buf)[j];
> + }
> +
> + return value;
> +} /* write8_reg() */
> +
> +/*
> + * read8_reg
> + * Recv byte from the TIS register according to the ST33ZP24 SPI protocol.
> + * @param: tpm, the chip description
> + * @param: tpm_register, the tpm tis register where the data should be read
> + * @param: tpm_data, the TPM response
> + * @param: tpm_size, tpm TPM response size to read.
> + * @return: number of byte read successfully: should be one if success.
> + */
> +static u8 read8_reg(struct tpm_chip *tpm, u8 tpm_register,
> + u8 *tpm_data, u16 tpm_size)
> +{
> + u8 data;
> + int i = 0, j;
> + int value = 0;
> + struct spi_device *dev = (struct spi_device *) tpm->vendor.iobase;
> + struct st33zp24_platform_data *platform_data = dev->dev.platform_data;
> + u8 *data_buffer = platform_data->tpm_spi_buffer[0];
> + struct spi_transfer xfer = {
> + .tx_buf = data_buffer,
> + .rx_buf = platform_data->tpm_spi_buffer[1],
> + };
> + struct spi_message msg;
> +
> + u8 latency = platform_data->latency + tpm_size + 1;
> +
> + FUNC_ENTER();
> + /* Pre-Header */
> +
> + data = tpm->vendor.locality;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> + data = tpm_register;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> +
> + for (j = 0 ; j < latency; j++) {
> + data = TPM_DUMMY_BYTE;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> + }
> + xfer.len = i;
> +
> + /* header + status byte + size of the data + status byte */
> + spi_message_init(&msg);
> + spi_message_add_tail(&xfer, &msg);
> + value = spi_sync(dev, &msg);
> + if (tpm_size > 0 && value == 0) {
> + j = 2;
> + for (; j < i && ((u8 *) xfer.rx_buf)[j] == 0; j++)
> + ;
> +
> + if (j + 1 < i) {
> + value = ((u8 *) xfer.rx_buf)[j];
> +
> + if (tpm_size > 0)
> + memcpy(tpm_data, xfer.rx_buf + j + 1,
> + tpm_size);
> + }
> + }
> + return value;
> +} /* read8_reg() */
> +
> +/*
> + * SPI_WRITE_DATA
> + * Send byte to the TIS register according to the ST33ZP24 SPI protocol.
> + * @param: tpm, the chip description
> + * @param: tpm_register, the tpm tis register where the data should be written
> + * @param: tpm_data, the tpm_data to write inside the tpm_register
> + * @param: tpm_size, The length of the data
> + * @return: number of byte written successfully: should be one if success.
> + */
> +static u32 SPI_WRITE_DATA(struct tpm_chip *tpm, u8 tpm_register,
> + u8 *tpm_data, u16 tpm_size)
> +{
> + u8 value = 0;
> +
> + FUNC_ENTER();
> +
> + value = write8_reg(tpm, tpm_register, tpm_data, tpm_size);
> +
> + switch (value) {
> + case TPM_ST_SPI_OK:
> + return TPM_ST_SPI_OK;
> + case 0:
> + return 0;
> + default:
> + return -EBUSY;
> + }
> +} /* SPI_WRITE_DATA() */
> +
> +/*
> + * SPI_READ_DATA
> + * Recv byte from the TIS register according to the ST33ZP24 SPI protocol.
> + * @param: tpm, the chip description
> + * @param: tpm_register, the tpm tis register where the data should be read
> + * @param: tpm_data, the TPM response
> + * @param: tpm_size, tpm TPM response size to read.
> + * @return: number of byte read successfully: should be one if success.
> + */
> +static u32 SPI_READ_DATA(struct tpm_chip *tpm, u8 tpm_register,
> + u8 *tpm_data, u16 tpm_size)
> +{
> + u8 value = 0;
> +
> + FUNC_ENTER();
> +
> + value = read8_reg(tpm, tpm_register, tpm_data, tpm_size);
> +
> + switch (value) {
> + case TPM_ST_SPI_OK:
> + return TPM_ST_SPI_OK;
> + case 0:
> + return 0;
> + default:
> + return -EBUSY;
> + }
> +} /* SPI_READ_DATA () */
> +
> +/*
> + * clear_interruption
> + * clear the TPM interrupt register.
> + * @param: tpm, the chip description
> + */
> +static void clear_interruption(struct tpm_chip *tpm)
> +{
> + u8 interrupt;
> + SPI_READ_DATA(tpm, TPM_INT_STATUS, &interrupt, 1);
> + /* Clear interrupts handled with TPM_EOI */
> + SPI_WRITE_DATA(tpm, TPM_INT_STATUS, &interrupt, 1);
> + SPI_READ_DATA(tpm, TPM_INT_STATUS, &interrupt, 1);
> +} /* clear_interruption() */
> +
> +/*
> + * _wait_for_interrupt_serirq_timeout
> + * @param: tpm, the chip description
> + * @param: timeout, the timeout of the interrupt
> + * @return: the status of the interruption.
> + */
> +static int _wait_for_interrupt_serirq_timeout(struct tpm_chip *chip,
> + unsigned long timeout)
> +{
> + unsigned long status;
> + struct spi_device *client;
> + struct st33zp24_platform_data *pin_infos;
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *) chip->vendor.iobase;
> + pin_infos = client->dev.platform_data;
> +
> + status = wait_for_completion_interruptible_timeout(
> + &pin_infos->irq_detection, timeout);
> + if (status > 0)
> + enable_irq(gpio_to_irq(pin_infos->io_serirq));
> + gpio_direction_input(pin_infos->io_serirq);
> +
> + return status;
> +} /* wait_for_interrupt_serirq_timeout() */
> +
> +unsigned long wait_for_serirq_timeout(struct tpm_chip *chip, bool condition,
> + unsigned long timeout)
> +{
> + unsigned long status = 0;
> + struct spi_device *client;
> + struct st33zp24_platform_data *pin_infos;
> +
> + client = (struct spi_device *) chip->vendor.iobase;
> + pin_infos = client->dev.platform_data;
> +
> + status = _wait_for_interrupt_serirq_timeout(chip, timeout);
> + if (!status) {
> + status = -EBUSY;
> + goto wait_end;
> + }
> + clear_interruption(chip);
> + if (condition)
> + status = 1;
> +
> +wait_end:
> + return status;
> +}
> +
> +
> +/*
> + * tpm_stm_spi_cancel, cancel is not implemented.
> + * @param: chip, the tpm chip description as specified in
> + * driver/char/tpm/tpm.h.
> + */
> +static void tpm_stm_spi_cancel(struct tpm_chip *chip)
> +{
> + struct spi_device *client;
> + u8 data = TPM_STS_COMMAND_READY;
> + client = (struct spi_device *) chip->vendor.iobase;
> +
> + FUNC_ENTER();
> +
> + /* this causes the current command to be aborted */
> + SPI_WRITE_DATA(chip, TPM_STS, &data, 1);
> +} /* tpm_stm_spi_cancel() */
> +
> +/*
> + * tpm_stm_spi_status return the TPM_STS register
> + * @param: chip, the tpm chip description
> + * @return: the TPM_STS register value.
> + */
> +static u8 tpm_stm_spi_status(struct tpm_chip *chip)
> +{
> + struct spi_device *client;
> + u8 data;
> + client = (struct spi_device *) chip->vendor.iobase;
> +
> + FUNC_ENTER();
> +
> + SPI_READ_DATA(chip, TPM_STS, &data, 1);
> + return data;
> +} /* tpm_stm_spi_status() */
> +
> +
> +
> +/*
> + * check_locality if the locality is active
> + * @param: chip, the tpm chip description
> + * @return: the active locality or -EACCESS.
> + */
> +static int check_locality(struct tpm_chip *chip)
> +{
> + struct spi_device *client;
> + u8 data;
> + u8 status;
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *) chip->vendor.iobase;
> +
> + status = SPI_READ_DATA(chip, TPM_ACCESS, &data, 1);
> + if (status && (data &
> + (TPM_ACCESS_ACTIVE_LOCALITY | TPM_ACCESS_VALID)) ==
> + (TPM_ACCESS_ACTIVE_LOCALITY | TPM_ACCESS_VALID))
> + return chip->vendor.locality;
> +
> + return -EACCES;
> +} /* check_locality() */
> +
> +/*
> + * request_locality request the TPM locality
> + * @param: chip, the chip description
> + * @return: the active locality or EACCESS.
> + */
> +static int request_locality(struct tpm_chip *chip)
> +{
> + unsigned long stop;
> + long rc;
> + u8 data;
> + struct spi_device *client;
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *) chip->vendor.iobase;
> + /* Check locality */
> + if (check_locality(chip) == chip->vendor.locality)
> + return chip->vendor.locality;
> +
> + /* Request locality */
> + data = TPM_ACCESS_REQUEST_USE;
> + rc = SPI_WRITE_DATA(chip, TPM_ACCESS, &data, 1);
> + if (rc < 0)
> + goto end;
> +
> + /* wait for burstcount */
> + if (chip->vendor.irq) {
> + rc = wait_for_serirq_timeout(chip, (check_locality
> + (chip) >= 0),
> + chip->vendor.timeout_a);
> + if (rc > 0)
> + return chip->vendor.locality;
> + } else {
> + stop = jiffies + chip->vendor.timeout_a;
> + do {
> + if (check_locality(chip) >= 0)
> + return chip->vendor.locality;
> + msleep(TPM_TIMEOUT);
> + } while (time_before(jiffies, stop));
> + }
> +end:
> + return -EACCES;
> +} /* request_locality() */
> +
> +/*
> + * release_locality release the active locality
> + * @param: chip, the tpm chip description.
> + */
> +static void release_locality(struct tpm_chip *chip)
> +{
> + struct spi_device *client;
> + u8 data;
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *) chip->vendor.iobase;
> + data = TPM_ACCESS_ACTIVE_LOCALITY;
> + SPI_WRITE_DATA(chip, TPM_ACCESS, &data, 1);
> +} /* release_locality()*/
> +
> +/*
> + * get_burstcount return the burstcount address 0x19 0x1A
> + * @param: chip, the chip description
> + * return: the burstcount.
> + */
> +static int get_burstcount(struct tpm_chip *chip)
> +{
> + unsigned long stop;
> + u32 burstcnt, status;
> + u8 tpm_reg, temp;
> +
> + FUNC_ENTER();
> +
> + /* wait for burstcount */
> + /* which timeout value, spec has 2 answers (c & d) */
> + stop = jiffies + chip->vendor.timeout_d;
> + do {
> + tpm_reg = TPM_STS + 1;
> + status = SPI_READ_DATA(chip, tpm_reg, &temp, 1);
> + if (status < 0)
> + goto end;
> +
> + tpm_reg = tpm_reg + 1;
> + burstcnt = temp;
> + status = SPI_READ_DATA(chip, tpm_reg, &temp, 1);
> + if (status < 0)
> + goto end;
> +
> + burstcnt |= temp << 8;
> + if (burstcnt)
> + return burstcnt;
> + msleep(TPM_TIMEOUT);
> + } while (time_before(jiffies, stop));
> +
> +end:
> + return -EBUSY;
> +} /* get_burstcount() */
> +
> +/*
> + * wait_for_stat wait for a TPM_STS value
> + * @param: chip, the tpm chip description
> + * @param: mask, the value mask to wait
> + * @param: timeout, the timeout
> + * @param: queue, the wait queue.
> + * @return: the tpm status, 0 if success, -ETIME if timeout is reached.
> + */
> +static int wait_for_stat(struct tpm_chip *chip, u8 mask, unsigned long timeout,
> + wait_queue_head_t *queue)
> +{
> + unsigned long stop;
> + long rc;
> + u8 status;
> +
> + FUNC_ENTER();
> +
> + /* check current status */
> + status = tpm_stm_spi_status(chip);
> + if (!chip->vendor.irq && (status & mask) == mask)
> + return 0;
> +
> + if (chip->vendor.irq) {
> + rc = wait_for_serirq_timeout(chip, ((tpm_stm_spi_status
> + (chip) & mask) ==
> + mask), timeout);
> + if (rc > 0)
> + return 0;
> + } else {
> + stop = jiffies + timeout;
> + do {
> + msleep(TPM_TIMEOUT);
> + status = tpm_stm_spi_status(chip);
> + if ((status & mask) == mask)
> + return 0;
> + } while (time_before(jiffies, stop));
> + }
> + return -ETIME;
> +} /* wait_for_stat() */
> +
> +/*
> + * recv_data receive data
> + * @param: chip, the tpm chip description
> + * @param: buf, the buffer where the data are received
> + * @param: count, the number of data to receive
> + * @return: the tpm status, 0 if success, -ETIME if timeout is reached.
> + */
> +static int recv_data(struct tpm_chip *chip, u8 *buf, size_t count)
> +{
> + u32 size = 0, burstcnt, status, len;
> + struct spi_device *client;
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *) chip->vendor.iobase;
> +
> + while (size < count &&
> + wait_for_stat(chip,
> + TPM_STS_DATA_AVAIL | TPM_STS_VALID,
> + chip->vendor.timeout_c,
> + &chip->vendor.read_queue)
> + == 0) {
> + burstcnt = get_burstcount(chip);
> + len = min_t(int, burstcnt, count - size);
> + status = SPI_READ_DATA(chip, TPM_DATA_FIFO, buf + size, len);
> + if (status < 0)
> + return status;
> +
> +
> + size += len;
> + }
> + return size;
> +}
> +
> +/*
> + * tpm_ioserirq_handler the serirq irq handler
> + * @param: irq, the tpm chip description
> + * @param: dev_id, the description of the chip
> + * @return: the status of the handler.
> + */
> +static irqreturn_t tpm_ioserirq_handler(int irq, void *dev_id)
> +{
> + struct tpm_chip *chip = dev_id;
> + struct spi_device *client;
> + struct st33zp24_platform_data *pin_infos;
> +
> + disable_irq_nosync(irq);
> + FUNC_ENTER();
> +
> + client = (struct spi_device *) chip->vendor.iobase;
> + pin_infos = client->dev.platform_data;
> +
> + complete(&pin_infos->irq_detection);
> + return IRQ_HANDLED;
> +} /* tpm_ioserirq_handler() */
> +
> +/*
> + * tpm_stm_spi_send send TPM commands through the SPI bus.
> + * @param: chip, the tpm chip description
> + * @param: buf, the tpm command buffer
> + * @param: len, the tpm command size
> + * @return: In case of success the number of bytes sent.
> + * In other case, a < 0 value describing the issue.
> + */
> +static int tpm_stm_spi_send(struct tpm_chip *chip, unsigned char *buf,
> + size_t len)
> +{
> + u32 ret = 0, ordinal,
> + status, burstcnt = 0, i, size = 0;
> + u8 data;
> +
> + struct spi_device *client;
> + struct st33zp24_platform_data *pin_infos;
> +
> + FUNC_ENTER();
> +
> + if (chip == NULL)
> + return -EBUSY;
> + if (len < TPM_HEADER_SIZE)
> + return -EBUSY;
> +
> + client = (struct spi_device *)chip->vendor.iobase;
> + pin_infos = client->dev.platform_data;
> +
> + ordinal = be32_to_cpu(*((__be32 *) (buf + 6)));
> +
> + ret = request_locality(chip);
> + if (ret < 0)
> + return ret;
> +
> + status = tpm_stm_spi_status(chip);
> + if ((status & TPM_STS_COMMAND_READY) == 0) {
> + tpm_stm_spi_cancel(chip);
> + if (wait_for_stat
> + (chip, TPM_STS_COMMAND_READY, chip->vendor.timeout_b,
> + &chip->vendor.int_queue) < 0) {
> + ret = -ETIME;
> + goto out_err;
> + }
> + }
> +
> + for (i = 0 ; i < len - 1 ;) {
> + burstcnt = get_burstcount(chip);
> + size = min_t(int, len - i - 1, burstcnt);
> + ret = SPI_WRITE_DATA(chip, TPM_DATA_FIFO, buf, size);
> + if (ret < 0)
> + goto out_err;
> + i += size;
> + }
> +
> + status = tpm_stm_spi_status(chip);
> + if ((status & TPM_STS_DATA_EXPECT) == 0) {
> + ret = -EIO;
> + goto out_err;
> + }
> +
> + /* write last byte */
> + SPI_WRITE_DATA(chip, TPM_DATA_FIFO, buf + len - 1, 1);
> +
> + status = tpm_stm_spi_status(chip);
> + if ((status & TPM_STS_DATA_EXPECT) != 0) {
> + ret = -EIO;
> + goto out_err;
> + }
> +
> + /* go and do it */
> + data = TPM_STS_GO;
> + ret = SPI_WRITE_DATA(chip, TPM_STS, &data, 1);
> + if (ret < 0)
> + goto out_err;
> +
> + return len;
> +out_err:
> + tpm_stm_spi_cancel(chip);
> + release_locality(chip);
> + return ret;
> +}
> +
> +/*
> + * tpm_stm_spi_recv received TPM response through the SPI bus.
> + * @param: chip, the tpm chip description
> + * @param: buf, the tpm command buffer
> + * @param: len, the tpm command size
> +* @return: In case of success the number of bytes received.
> + * In other case, a < 0 value describing the issue.
> + */
> +static int tpm_stm_spi_recv(struct tpm_chip *chip, unsigned char *buf,
> + size_t count)
> +{
> + int size = 0;
> + int expected;
> +
> + struct spi_device *client;
> + struct st33zp24_platform_data *pin_infos;
> +
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *)chip->vendor.iobase;
> + pin_infos = client->dev.platform_data;
> +
> +
> + if (chip == NULL)
> + return -EBUSY;
> + if (count < TPM_HEADER_SIZE) {
> + size = -EIO;
> + goto out;
> + }
> +
> + size = recv_data(chip, buf, TPM_HEADER_SIZE);
> +
> + /* read first 10 bytes, including tag, paramsize, and result */
> + if (size < TPM_HEADER_SIZE) {
> + dev_err(chip->dev, "Unable to read header\n");
> + goto out;
> + }
> +
> + expected = be32_to_cpu(*(__be32 *) (buf + 2));
> + if (expected > count) {
> + size = -EIO;
> + goto out;
> + }
> +
> + size += recv_data(chip, &buf[TPM_HEADER_SIZE],
> + expected - TPM_HEADER_SIZE);
> + if (size < expected) {
> + dev_err(chip->dev, "Unable to read remainder of result\n");
> + size = -ETIME;
> + goto out;
> + }
> +
> +out:
> + chip->vendor.cancel(chip);
> + release_locality(chip);
> + return size;
> +}
> +
> +
> +static const struct file_operations tpm_st33_spi_fops = {
> + .owner = THIS_MODULE,
> + .llseek = no_llseek,
> + .read = tpm_read,
> + .write = tpm_write,
> + .open = tpm_open,
> + .release = tpm_release,
> +};
> +
> +static DEVICE_ATTR(pubek, S_IRUGO, tpm_show_pubek, NULL);
> +static DEVICE_ATTR(pcrs, S_IRUGO, tpm_show_pcrs, NULL);
> +static DEVICE_ATTR(enabled, S_IRUGO, tpm_show_enabled, NULL);
> +static DEVICE_ATTR(active, S_IRUGO, tpm_show_active, NULL);
> +static DEVICE_ATTR(owned, S_IRUGO, tpm_show_owned, NULL);
> +static DEVICE_ATTR(temp_deactivated, S_IRUGO, tpm_show_temp_deactivated, NULL);
> +static DEVICE_ATTR(caps, S_IRUGO, tpm_show_caps_1_2, NULL);
> +static DEVICE_ATTR(cancel, S_IWUSR | S_IWGRP, NULL, tpm_store_cancel);
> +
> +static struct attribute *stm_tpm_attrs[] = {
> + &dev_attr_pubek.attr,
> + &dev_attr_pcrs.attr,
> + &dev_attr_enabled.attr,
> + &dev_attr_active.attr,
> + &dev_attr_owned.attr,
> + &dev_attr_temp_deactivated.attr,
> + &dev_attr_caps.attr,
> + &dev_attr_cancel.attr, NULL,
> +};
> +
> +static struct attribute_group stm_tpm_attr_grp = {
> + .attrs = stm_tpm_attrs
> +};
> +
> +static struct tpm_vendor_specific st_spi_tpm = {
> + .send = tpm_stm_spi_send,
> + .recv = tpm_stm_spi_recv,
> + .cancel = tpm_stm_spi_cancel,
> + .status = tpm_stm_spi_status,
> + .attr_group = &stm_tpm_attr_grp,
> + .miscdev = {.fops = &tpm_st33_spi_fops,},
> +};
> +
> +static int evaluate_latency(struct tpm_chip *chip)
> +{
> + int latency = 0;
> + struct spi_device *dev = (struct spi_device *) chip->vendor.iobase;
> + struct st33zp24_platform_data *platform_data = dev->dev.platform_data;
> + int status = 0;
> + u8 data;
> +
> + for (; status == 0x00 && latency < MAX_SPI_LATENCY ; latency++) {
> + platform_data->latency = latency;
> + status = SPI_READ_DATA(chip, TPM_INTF_CAPABILITY, &data, 1);
> + }
> + return latency - 1;
> +} /* evaluate_latency() */
> +
> +static int interrupts;
> +module_param(interrupts, int, 0444);
> +MODULE_PARM_DESC(interrupts, "Enable interrupts");
> +
> +static int power_mgt = 1;
> +module_param(power_mgt, int, 0444);
> +MODULE_PARM_DESC(power_mgt, "Power Management");
> +
> +/*
> + * tpm_st33_spi_probe initialize the TPM device
> + * @param: client, the spi_device drescription (TPM SPI description).
> + * @param: id, the spi_device_id struct.
> + * @return: 0 in case of success.
> + * -1 in other case.
> + */
> +static int
> +tpm_st33_spi_probe(struct spi_device *dev)
> +{
> + u32 err;
> + u8 intmask;
> + struct tpm_chip *chip;
> + struct st33zp24_platform_data *platform_data;
> +
> + FUNC_ENTER();
> +
> + err = 0;
> +
> + /* Check SPI platform functionnalities */
> + if (dev == NULL) {
> + pr_info("dev is NULL. exiting.\n");
> + err = -ENODEV;
> + goto end;
> + }
> +
> + chip = tpm_register_hardware(&dev->dev, &st_spi_tpm);
> + if (!chip) {
> + err = -ENODEV;
> + goto end;
> + }
> +
> + /* Allocation of SPI buffers MISO and MOSI */
> + /* Size is as follow: */
> + /* Request burstcount value = 0x800 = 2048 */
> + /* + */
> + /* Response burstcount value = 0x400 = 1024 */
> + /* + */
> + /* At least: */
> + /* 1 byte for direction/locality */
> + /* 1 byte tpm tis register */
> + /* 2 bytes spi data length (for request only) */
> + /* 2 latency bytes */
> + /* 1 status byte */
> + /* = 2048 + 1024 + 7 */
> + /* We reserved 2048 + 1024 + 20 in case latency byte */
> + /* change */
> + platform_data = dev->dev.platform_data;
> + platform_data->tpm_spi_buffer[0] =
> + kmalloc((TPM_BUFSIZE + (TPM_BUFSIZE / 2) +
> + TPM_DIGEST_SIZE) * sizeof(u8), GFP_KERNEL);
> + if (platform_data->tpm_spi_buffer[0] == NULL) {
> + err = -ENOMEM;
> + goto _tpm_clean_answer;
> + }
> + platform_data->tpm_spi_buffer[1] =
> + kmalloc((TPM_BUFSIZE + (TPM_BUFSIZE / 2) +
> + TPM_DIGEST_SIZE) * sizeof(u8) , GFP_KERNEL);
> + if (platform_data->tpm_spi_buffer[1] == NULL) {
> + err = -ENOMEM;
> + goto _tpm_clean_response;
> + }
> +
> + chip->vendor.iobase = dev;
> +
> + /* Default timeouts */
> + chip->vendor.timeout_a = msecs_to_jiffies(TIS_SHORT_TIMEOUT);
> + chip->vendor.timeout_b = msecs_to_jiffies(TIS_LONG_TIMEOUT);
> + chip->vendor.timeout_c = msecs_to_jiffies(TIS_SHORT_TIMEOUT);
> + chip->vendor.timeout_d = msecs_to_jiffies(TIS_SHORT_TIMEOUT);
> + chip->vendor.locality = LOCALITY0;
> +
> + if (power_mgt) {
> + err = gpio_request(platform_data->io_lpcpd, "TPM IO_LPCPD");
> + if (err)
> + goto _gpio_init1;
> + gpio_set_value(platform_data->io_lpcpd, 1);
> + }
> +
> + platform_data->latency = evaluate_latency(chip);
> + if (platform_data->latency <= 0x00) {
> + err = -ENODEV;
> + goto _gpio_init1;
> + }
> +
> + /* Enable interrupt */
> + /* Register GPIO pin through generic Linux GPIO API */
> + if (interrupts) {
> + init_completion(&platform_data->irq_detection);
> + if (request_locality(chip) != LOCALITY0) {
> + err = -ENODEV;
> + goto _tpm_clean_response;
> + }
> + err = gpio_request(platform_data->io_serirq, "TPM IO_SERIRQ");
> + if (err)
> + goto _gpio_init2;
> +
> + /* Clear all existing */
> + clear_interruption(chip);
> + err = request_irq(gpio_to_irq(platform_data->io_serirq),
> + &tpm_ioserirq_handler,
> + IRQF_TRIGGER_HIGH | IRQF_SHARED,
> + "TPM SERIRQ management", chip);
> + if (err < 0) {
> +
> + pr_info("TPM SERIRQ signals %d not available\n",
> + gpio_to_irq(platform_data->io_serirq));
> + goto _irq_set;
> + }
> + err = SPI_READ_DATA(chip, TPM_INT_ENABLE, &intmask, 1);
> + if (err < 0)
> + goto _irq_set;
> +
> + intmask |= TPM_INTF_CMD_READY_INT
> + | TPM_INTF_FIFO_AVALAIBLE_INT
> + | TPM_INTF_WAKE_UP_READY_INT
> + | TPM_INTF_LOC4SOFTRELEASE_INT
> + | TPM_INTF_LOCALITY_CHANGE_INT
> + | TPM_INTF_STS_VALID_INT
> + | TPM_INTF_DATA_AVAIL_INT;
> +
> + err = SPI_WRITE_DATA(chip, TPM_INT_ENABLE, &intmask, 1);
> + if (err < 0)
> + goto _irq_set;
> +
> + intmask = TPM_GLOBAL_INT_ENABLE;
> + err = SPI_WRITE_DATA(chip, TPM_INT_ENABLE + 3, &intmask, 1);
> + if (err < 0)
> + goto _irq_set;
> +
> + err = SPI_READ_DATA(chip, TPM_INT_STATUS, &intmask, 1);
> + if (err < 0)
> + goto _irq_set;
> +
> + chip->vendor.irq = interrupts;
> +
> + tpm_gen_interrupt(chip);
> + }
> +
> + tpm_get_timeouts(chip);
> +
> + /* attach chip datas to client */
> + spi_set_drvdata(dev, chip);
> + platform_data->bChipF = false;
> +
> + pr_info("TPM SPI Initialized\n");
> + return 0;
> +_irq_set:
> + free_irq(gpio_to_irq(platform_data->io_serirq), chip);
> +_gpio_init2:
> + if (platform_data && interrupts)
> + gpio_free(platform_data->io_serirq);
> +_gpio_init1:
> + if (platform_data && power_mgt)
> + gpio_free(platform_data->io_lpcpd);
> +_tpm_clean_response:
> + tpm_remove_hardware(chip->dev);
> + if (platform_data->tpm_spi_buffer[1] != NULL) {
> + kfree(platform_data->tpm_spi_buffer[1]);
> + platform_data->tpm_spi_buffer[1] = NULL;
> + }
> +_tpm_clean_answer:
> + if (platform_data->tpm_spi_buffer[0] != NULL) {
> + kfree(platform_data->tpm_spi_buffer[0]);
> + platform_data->tpm_spi_buffer[0] = NULL;
> + }
> +
> + platform_data->bChipF = true;
> +end:
> + pr_info("TPM SPI initialisation fail\n");
> + return err;
> +}
> +
> +/*
> + * tpm_st33_spi_remove remove the TPM device
> + * @param: client, the spi_device drescription (TPM SPI description).
> + clear_bit(0, &chip->is_open);
> + * @return: 0 in case of success.
> + */
> +static int tpm_st33_spi_remove(struct spi_device *client)
> +{
> + struct tpm_chip *chip = (struct tpm_chip *)spi_get_drvdata(client);
> + struct st33zp24_platform_data *pin_infos =
> + ((struct spi_device *) chip->vendor.iobase)->dev.platform_data;
> +
> + FUNC_ENTER();
> +
> + if (pin_infos != NULL) {
> + gpio_free(pin_infos->io_lpcpd);
> +
> + /* Check if chip has been previously clean */
> + if (pin_infos->bChipF != true)
> + tpm_remove_hardware(chip->dev);
> + if (pin_infos->tpm_spi_buffer[1] != NULL) {
> + kfree(pin_infos->tpm_spi_buffer[1]);
> + pin_infos->tpm_spi_buffer[1] = NULL;
> + }
> + if (pin_infos->tpm_spi_buffer[0] != NULL) {
> + kfree(pin_infos->tpm_spi_buffer[0]);
> + pin_infos->tpm_spi_buffer[0] = NULL;
> + }
> + }
> +
> + return 0;
> +}
> +
> +/*
> + * tpm_st33_spi_pm_suspend suspend the TPM device
> + * Added: Work around when suspend and no tpm application is running, suspend
> + * may fail because chip->data_buffer is not set (only set in tpm_open in Linux
> + * TPM core)
> + * @param: client, the spi_device drescription (TPM SPI description).
> + * @param: mesg, the power management message.
> + * @return: 0 in case of success.
> + */
> +static int tpm_st33_spi_pm_suspend(struct spi_device *client,
> + pm_message_t mesg)
> +{
> + struct tpm_chip *chip =
> + (struct tpm_chip *)spi_get_drvdata(client);
> + struct st33zp24_platform_data *pin_infos =
> + ((struct spi_device *)chip->vendor.iobase)->dev.platform_data;
> + int ret = 0;
> +
> + if (power_mgt)
> + gpio_set_value(pin_infos->io_lpcpd, 0);
> + else {
> + if (chip->data_buffer == NULL)
> + chip->data_buffer = pin_infos->tpm_spi_buffer[0];
> + ret = tpm_pm_suspend(&client->dev);
> + }
> + return ret;
> +} /* tpm_st33_spi_suspend() */
> +
> +/*
> + * tpm_st33_spi_pm_resume resume the TPM device
> + * @param: spi, the spi_device drescription (TPM SPI description).
> + * @return: 0 in case of success.
> + */
> +static int tpm_st33_spi_pm_resume(struct spi_device *spi)
> +{
> + struct tpm_chip *chip =
> + (struct tpm_chip *)spi_get_drvdata(spi);
> + struct st33zp24_platform_data *pin_infos =
> + ((struct spi_device *)chip->vendor.iobase)->dev.platform_data;
> +
> + int ret = 0;
> + if (power_mgt) {
> + gpio_set_value(pin_infos->io_lpcpd, 1);
> + ret = wait_for_serirq_timeout(chip,
> + (chip->vendor.status(chip) &&
> + TPM_STS_VALID) == TPM_STS_VALID,
> + chip->vendor.timeout_b);
> + } else {
> + if (chip->data_buffer == NULL)
> + chip->data_buffer = pin_infos->tpm_spi_buffer[0];
> + ret = tpm_pm_resume(&spi->dev);
> + if (!ret)
> + tpm_do_selftest(chip);
> + }
> + return ret;
> +} /* tpm_st33_spi_pm_resume() */
> +
> +static struct spi_driver tpm_st33_spi_driver = {
> + .driver = {
> + .owner = THIS_MODULE,
> + .name = TPM_ST33_SPI,
> + },
> + .probe = tpm_st33_spi_probe,
> + .remove = tpm_st33_spi_remove,
> + .resume = tpm_st33_spi_pm_resume,
> + .suspend = tpm_st33_spi_pm_suspend,
> +};
> +
> +/*
> + * tpm_st33_spi_init initialize driver
> + * @return: 0 if successful, else non zero value.
> + */
> +static int __init tpm_st33_spi_init(void)
> +{
> + FUNC_ENTER();
> + return spi_register_driver(&tpm_st33_spi_driver);
> +}
> +
> +/*
> + * tpm_st33_spi_exit The kernel calls this function during unloading the
> + * module or during shut down process
> + */
> +static void __exit tpm_st33_spi_exit(void)
> +{
> + FUNC_ENTER();
> + spi_unregister_driver(&tpm_st33_spi_driver);
> +}
> +
> +module_init(tpm_st33_spi_init);
> +module_exit(tpm_st33_spi_exit);
> +
> +MODULE_AUTHOR("Christophe Ricard ([email protected])");
> +MODULE_DESCRIPTION("STM TPM SPI ST33 Driver");
> +MODULE_VERSION("1.2.0");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/char/tpm/tpm_spi_stm_st33.h b/drivers/char/tpm/tpm_spi_stm_st33.h
> new file mode 100644
> index 0000000..42bae6f
> --- /dev/null
> +++ b/drivers/char/tpm/tpm_spi_stm_st33.h
> @@ -0,0 +1,75 @@
> +/*
> + * STMicroelectronics TPM SPI Linux driver for TPM ST33NP18
> + * Copyright (C) 2009, 2010 STMicroelectronics
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License along
> + * with this program; if not, write to the Free Software Foundation, Inc.,
> + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
> + *
> + * STMicroelectronics version 1.2.0, Copyright (C) 2010
> + * STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
> + * This is free software, and you are welcome to redistribute it
> + * under certain conditions.
> + *
> + * @Author: Christophe RICARD [email protected]
> + *
> + * @File: tpm_spi_stm_st33.h
> + *
> + * @Date: 09/15/2010
> + */
> +#ifndef __STM_ST33_TPM_SPI_MAIN_H__
> +#define __STM_ST33_TPM_SPI_MAIN_H__
> +
> +#include <linux/pci.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/fs.h>
> +#include <linux/miscdevice.h>
> +
> +#define MINOR_NUM_SPI 224
> +
> +#define TPM_ACCESS (0x0)
> +#define TPM_STS (0x18)
> +#define TPM_HASH_END (0x20)
> +#define TPM_DATA_FIFO (0x24)
> +#define TPM_HASH_DATA (0x24)
> +#define TPM_HASH_START (0x28)
> +#define TPM_INTF_CAPABILITY (0x14)
> +#define TPM_INT_STATUS (0x10)
> +#define TPM_INT_ENABLE (0x08)
> +
> +#define TPM_DUMMY_BYTE 0x00
> +#define TPM_WRITE_DIRECTION 0x80
> +#define TPM_HEADER_SIZE 10
> +#define TPM_BUFSIZE 2048
> +
> +/* ioctl commands */
> +#define TPMIOC_CANCEL _IO('T', 0x00)
> +#define TPMIOC_TRANSMIT _IO('T', 0x01)
> +#define TPMIOC_HASH _IO('T', 0x02)
> +#define TPMIOC_CHANGELOCALITY _IO('T', 0x03)
> +
> +#define LOCALITY0 0
> +#define LOCALITY4 4
> +
> +#define TPM_ST_SPI_OK 0x5A
> +
> +
> +#define MAX_SPI_LATENCY 15
> +
> +struct st_tpm_hash_t {
> + int size;
> + u8 *data;
> +};
> +
> +#endif /* __STM_ST33_TPM_SPI_MAIN_H__ */
> diff --git a/include/linux/spi/tpm_spi_stm_st33.h b/include/linux/spi/tpm_spi_stm_st33.h
> new file mode 100644
> index 0000000..c233ff6
> --- /dev/null
> +++ b/include/linux/spi/tpm_spi_stm_st33.h
> @@ -0,0 +1,46 @@
> +/*
> +* STMicroelectronics TPM SPI Linux driver for TPM ST33NP18
> +* Copyright (C) 2009, 2010 STMicroelectronics
> +* Christophe RICARD [email protected]
> +* This program is free software; you can redistribute it and/or modify
> +* it under the terms of the GNU General Public License as published by
> +* the Free Software Foundation; either version 2 of the License, or
> +* (at your option) any later version.
> +*
> +* This program is distributed in the hope that it will be useful,
> +* but WITHOUT ANY WARRANTY; without even the implied warranty of
> +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +* GNU General Public License for more details.
> +*
> +* You should have received a copy of the GNU General Public License along
> +* with this program; if not, write to the Free Software Foundation, Inc.,
> +* 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
> +*
> +* STMicroelectronics version 1.2.0, Copyright (C) 2010
> +* STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
> +* This is free software, and you are welcome to redistribute it
> +* under certain conditions.
> +*
> +* @File: tpm_spi_stm_st33.h
> +*
> +* @Date: 06/15/2008
> +*/
> +#ifndef __STM_ST33_TPM_SPI_H__
> +#define __STM_ST33_TPM_SPI_H__
> +
> +#include <linux/spi/spi.h>
> +
> +#define TPM_ST33_SPI "st33zp24_spi"
> +
> +#ifndef __STM_ST33_TPM_SPI_H__
> +struct st33zp24_platform_data {
> + int io_serirq;
> + int io_lpcpd;
> + int latency;
> + bool bChipF;
> + u8 *tpm_spi_buffer[2]; /* 0 Request 1 Response */
> + struct completion irq_detection;
> +};
> +#endif
> +
> +#endif /* __STM_ST33_TPM_SPI_H__ */
> --
> 1.7.1
>
>
> ------------------------------------------------------------------------------
> Everyone hates slow websites. So do we.
> Make your web apps faster with AppDynamics
> Download AppDynamics Lite for free today:
> http://p.sf.net/sfu/appdyn_d2d_mar
> _______________________________________________
> tpmdd-devel mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/tpmdd-devel
Sorry for this mistake, admin01 the name of my platform development , git is not configured on it.
-----Original Message-----
From: Kent Yoder [mailto:[email protected]]
Sent: 25 March, 2013 17:44
To: Mathias LEBLANC
Cc: Kent Yoder; Rajiv Andrade; Marcel Selhorst; Sirrix AG; [email protected]; Jean-Luc BLANC; [email protected]
Subject: Re: [tpmdd-devel] [PATCH 1/1] TPM: STMicroelectronics st33 driver SPI
On Mon, Mar 25, 2013 at 10:08 AM, Matthias Leblanc <[email protected]> wrote:
> From: admin01 <admin01@admin01-desktop.(none)>
>
> * STMicroelectronics version 1.2.0, Copyright (C) 2010
> * STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
> * This is free software, and you are welcome to redistribute it
> * under certain conditions.
>
> This is the driver for TPM chip from ST Microelectronics.
>
> If you have a TPM security chip from STMicroelectronics working with
> an I2C/SPI, in menuconfig or .config choose the tpm driver on device
> --> tpm and activate the protocol of your choice before compiling the
> kernel.
> The driver will be accessible from within Linux.
>
> Tested on linux x86/x64 and beagleboard REV B & XM REV C
>
> Signed-off-by: admin01 <admin01@admin01-desktop.(none)>
Who is admin01 and why is he signing off your patches? :-)
Kent
> ---
> arch/arm/mach-omap2/board-omap3beagle.c | 40 ++
> drivers/char/tpm/Kconfig | 10 +
> drivers/char/tpm/Makefile | 1 +
> drivers/char/tpm/tpm_spi_stm_st33.c | 1116 +++++++++++++++++++++++++++++++
> drivers/char/tpm/tpm_spi_stm_st33.h | 75 ++
> include/linux/spi/tpm_spi_stm_st33.h | 46 ++
> 6 files changed, 1287 insertions(+), 0 deletions(-) create mode
> 100644 drivers/char/tpm/tpm_spi_stm_st33.c
> create mode 100644 drivers/char/tpm/tpm_spi_stm_st33.h
> create mode 100644 include/linux/spi/tpm_spi_stm_st33.h
>
> diff --git a/arch/arm/mach-omap2/board-omap3beagle.c
> b/arch/arm/mach-omap2/board-omap3beagle.c
> index c3558f9..72e6513 100644
> --- a/arch/arm/mach-omap2/board-omap3beagle.c
> +++ b/arch/arm/mach-omap2/board-omap3beagle.c
> @@ -46,6 +46,11 @@
> #include <video/omap-panel-tfp410.h>
> #include <linux/platform_data/mtd-nand-omap2.h>
>
> +#ifdef CONFIG_TCG_ST33_SPI
> +#include <linux/spi/tpm_spi_stm_st33.h> #include <linux/spi/spi.h>
> +#endif /* CONFIG_TCG_ST33_SPI */
> +
> #include "common.h"
> #include "omap_device.h"
> #include "gpmc.h"
> @@ -375,6 +380,26 @@ static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
> },
> };
>
> +#if defined CONFIG_TCG_ST33_I2C || defined CONFIG_TCG_ST33_SPI static
> +struct st33zp24_platform_data tpm_data = {
> + .io_serirq = 136,
> + .io_lpcpd = 143,
> +};
> +#endif
> +
> +#ifdef CONFIG_TCG_ST33_SPI
> +static struct spi_board_info tpm_st33_spi_board_info[] = {
> + {
> + .modalias = TPM_ST33_SPI,
> + .max_speed_hz = 10000000,
> + .bus_num = 4,
> + .chip_select = 0,
> + .mode = SPI_MODE_0,
> + .platform_data = &tpm_data,
> + },
> +};
> +#endif
> +
> static int __init omap3_beagle_i2c_init(void) {
> omap3_pmic_get_config(&beagle_twldata,
> @@ -556,6 +581,20 @@ static void __init omap3_beagle_init(void)
> omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
> omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
>
> + #if defined CONFIG_TCG_ST33_I2C || defined CONFIG_TCG_ST33_SPI
> + omap_mux_init_gpio(tpm_data.io_serirq, OMAP_PIN_INPUT);
> + omap_mux_init_gpio(tpm_data.io_lpcpd, OMAP_PIN_OUTPUT);
> + #endif
> +
> + #ifdef CONFIG_TCG_ST33_SPI
> + omap_mux_init_signal("mcspi4_clk", OMAP_PIN_INPUT);
> + omap_mux_init_signal("mcspi4_cs0", OMAP_PIN_OUTPUT);
> + omap_mux_init_signal("mcspi4_simo", OMAP_PIN_OUTPUT);
> + omap_mux_init_signal("mcspi4_somi", OMAP_PIN_INPUT);
> +
> + spi_register_board_info(tpm_st33_spi_board_info,
> + ARRAY_SIZE(tpm_st33_spi_board_info));
> + #endif
> +
> pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup)); }
>
> diff --git a/drivers/char/tpm/Kconfig b/drivers/char/tpm/Kconfig index
> dbfd564..2fc1254 100644
> --- a/drivers/char/tpm/Kconfig
> +++ b/drivers/char/tpm/Kconfig
> @@ -91,4 +91,14 @@ config TCG_ST33_I2C
> To compile this driver as a module, choose M here; the module will be
> called tpm_stm_st33_i2c.
>
> +config TCG_ST33_SPI
> + tristate "STMicroelectronics ST33 SPI"
> + depends on SPI
> + depends on GPIOLIB
> + ---help---
> + If you have a TPM security chip from STMicroelectronics working with
> + an SPI bus say Yes and it will be accessible from within Linux.
> + To compile this driver as a module, choose M here; the module will be
> + called tpm_stm_st33_spi.
> +
> endif # TCG_TPM
> diff --git a/drivers/char/tpm/Makefile b/drivers/char/tpm/Makefile
> index a3736c9..a1db3dd 100644
> --- a/drivers/char/tpm/Makefile
> +++ b/drivers/char/tpm/Makefile
> @@ -18,3 +18,4 @@ obj-$(CONFIG_TCG_ATMEL) += tpm_atmel.o
> obj-$(CONFIG_TCG_INFINEON) += tpm_infineon.o
> obj-$(CONFIG_TCG_IBMVTPM) += tpm_ibmvtpm.o
> obj-$(CONFIG_TCG_ST33_I2C) += tpm_i2c_stm_st33.o
> +obj-$(CONFIG_TCG_ST33_SPI) += tpm_spi_stm_st33.o
> diff --git a/drivers/char/tpm/tpm_spi_stm_st33.c
> b/drivers/char/tpm/tpm_spi_stm_st33.c
> new file mode 100644
> index 0000000..a47c647
> --- /dev/null
> +++ b/drivers/char/tpm/tpm_spi_stm_st33.c
> @@ -0,0 +1,1116 @@
> +/*
> + * STMicroelectronics TPM SPI Linux driver for TPM ST33ZP24
> + * Copyright (C) 2009, 2010 STMicroelectronics
> + *
> + * This program is free software; you can redistribute it and/or
> +modify
> + * it under the terms of the GNU General Public License as published
> +by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> +along
> + * with this program; if not, write to the Free Software Foundation,
> +Inc.,
> + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
> + *
> + * STMicroelectronics version 1.2.0, Copyright (C) 2010
> + * STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
> + * This is free software, and you are welcome to redistribute it
> + * under certain conditions.
> + *
> + * @Author: Christophe RICARD [email protected]
> + *
> + * @File: tpm_stm_st33_spi.c
> + *
> + * @Synopsis:
> + * 09/15/2010: First shot driver tpm_tis driver for lpc is
> + * used as model.
> + */
> +
> +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
> +
> +#include <linux/module.h>
> +#include <linux/kernel.h>
> +#include <linux/delay.h>
> +#include <linux/init.h>
> +#include <linux/spi/spi.h>
> +#include <linux/wait.h>
> +#include <linux/string.h>
> +#include <linux/interrupt.h>
> +#include <linux/spinlock.h>
> +#include <linux/sysfs.h>
> +#include <linux/gpio.h>
> +#include <linux/sched.h>
> +#include <linux/uaccess.h>
> +#include <linux/io.h>
> +#include <linux/slab.h>
> +#include <linux/sched.h>
> +
> +#include <linux/spi/tpm_spi_stm_st33.h>
> +
> +#include "tpm.h"
> +
> +#include "tpm_spi_stm_st33.h"
> +
> +#ifdef DEBUG
> +#define FUNC_ENTER() pr_info("%s\n", __func__)
> +#else
> +#define FUNC_ENTER() do {} while (0)
> +#endif
> +
> +enum stm33zp24_access {
> + TPM_ACCESS_VALID = 0x80,
> + TPM_ACCESS_ACTIVE_LOCALITY = 0x20,
> + TPM_ACCESS_REQUEST_PENDING = 0x04,
> + TPM_ACCESS_REQUEST_USE = 0x02, };
> +
> +enum stm33zp24_status {
> + TPM_STS_VALID = 0x80,
> + TPM_STS_COMMAND_READY = 0x40,
> + TPM_STS_GO = 0x20,
> + TPM_STS_DATA_AVAIL = 0x10,
> + TPM_STS_DATA_EXPECT = 0x08,
> +};
> +
> +enum stm33zp24_int_flags {
> + TPM_GLOBAL_INT_ENABLE = 0x80,
> + TPM_INTF_CMD_READY_INT = 0x080,
> + TPM_INTF_FIFO_AVALAIBLE_INT = 0x040,
> + TPM_INTF_WAKE_UP_READY_INT = 0x020,
> + TPM_INTF_LOC4SOFTRELEASE_INT = 0x008,
> + TPM_INTF_LOCALITY_CHANGE_INT = 0x004,
> + TPM_INTF_STS_VALID_INT = 0x002,
> + TPM_INTF_DATA_AVAIL_INT = 0x001, };
> +
> +enum tis_defaults {
> + TIS_SHORT_TIMEOUT = 750, /* ms */
> + TIS_LONG_TIMEOUT = 2000, /* 2 sec */
> +};
> +
> +/*
> + * write8_reg
> + * Send byte to the TIS register according to the ST33ZP24 SPI protocol.
> + * @param: tpm, the chip description
> + * @param: tpm_register, the tpm tis register where the data should
> +be written
> + * @param: tpm_data, the tpm_data to write inside the tpm_register
> + * @param: tpm_size, The length of the data
> + * @return: number of byte written successfully: should be one if success.
> + */
> +static int write8_reg(struct tpm_chip *tpm, u8 tpm_register,
> + u8 *tpm_data, u16 tpm_size) {
> + /* u8 LOC+DIR u8 ADD u16 LENGHT u8* data */
> + /* u8 LATENCY u8 LATENCY */
> +
> + u8 data;
> + int i = 0, j;
> + int value = 0;
> + struct spi_device *dev = (struct spi_device *) tpm->vendor.iobase;
> + struct st33zp24_platform_data *platform_data = dev->dev.platform_data;
> + u8 *data_buffer = platform_data->tpm_spi_buffer[0];
> + struct spi_transfer xfer = {
> + .tx_buf = data_buffer,
> + .rx_buf = platform_data->tpm_spi_buffer[1],
> + };
> + struct spi_message msg;
> + u8 latency = platform_data->latency + tpm_size + 1;
> +
> +
> + FUNC_ENTER();
> + /* Pre-Header */
> +
> + data = TPM_WRITE_DIRECTION | tpm->vendor.locality;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> + data = tpm_register;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> +
> + if (tpm_size > 0 &&
> + (tpm_register == TPM_DATA_FIFO ||
> + tpm_register == TPM_HASH_DATA)) {
> + data = tpm_size >> 8 & 0x00ff;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> + data = tpm_size & 0x00ff;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> + latency -= 2;
> + }
> +
> + memcpy(data_buffer + i, tpm_data, tpm_size);
> + i += tpm_size;
> +
> + for (j = 0 ; j < platform_data->latency + 1; j++) {
> + data = TPM_DUMMY_BYTE;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> + }
> + xfer.len = i;
> + spi_message_init(&msg);
> + spi_message_add_tail(&xfer, &msg);
> + value = spi_sync(dev, &msg);
> +
> + if (value == 0) {
> + j = i - 1 - j;
> + for (; j < i && ((u8 *) xfer.rx_buf)[j] == 0; j++)
> + ;
> +
> + if (((u8 *) xfer.rx_buf)[j] != 0)
> + value = ((u8 *) xfer.rx_buf)[j];
> + }
> +
> + return value;
> +} /* write8_reg() */
> +
> +/*
> + * read8_reg
> + * Recv byte from the TIS register according to the ST33ZP24 SPI protocol.
> + * @param: tpm, the chip description
> + * @param: tpm_register, the tpm tis register where the data should
> +be read
> + * @param: tpm_data, the TPM response
> + * @param: tpm_size, tpm TPM response size to read.
> + * @return: number of byte read successfully: should be one if success.
> + */
> +static u8 read8_reg(struct tpm_chip *tpm, u8 tpm_register,
> + u8 *tpm_data, u16 tpm_size) {
> + u8 data;
> + int i = 0, j;
> + int value = 0;
> + struct spi_device *dev = (struct spi_device *) tpm->vendor.iobase;
> + struct st33zp24_platform_data *platform_data = dev->dev.platform_data;
> + u8 *data_buffer = platform_data->tpm_spi_buffer[0];
> + struct spi_transfer xfer = {
> + .tx_buf = data_buffer,
> + .rx_buf = platform_data->tpm_spi_buffer[1],
> + };
> + struct spi_message msg;
> +
> + u8 latency = platform_data->latency + tpm_size + 1;
> +
> + FUNC_ENTER();
> + /* Pre-Header */
> +
> + data = tpm->vendor.locality;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> + data = tpm_register;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> +
> + for (j = 0 ; j < latency; j++) {
> + data = TPM_DUMMY_BYTE;
> + memcpy(data_buffer + i, &data, sizeof(data));
> + i++;
> + }
> + xfer.len = i;
> +
> + /* header + status byte + size of the data + status byte */
> + spi_message_init(&msg);
> + spi_message_add_tail(&xfer, &msg);
> + value = spi_sync(dev, &msg);
> + if (tpm_size > 0 && value == 0) {
> + j = 2;
> + for (; j < i && ((u8 *) xfer.rx_buf)[j] == 0; j++)
> + ;
> +
> + if (j + 1 < i) {
> + value = ((u8 *) xfer.rx_buf)[j];
> +
> + if (tpm_size > 0)
> + memcpy(tpm_data, xfer.rx_buf + j + 1,
> + tpm_size);
> + }
> + }
> + return value;
> +} /* read8_reg() */
> +
> +/*
> + * SPI_WRITE_DATA
> + * Send byte to the TIS register according to the ST33ZP24 SPI protocol.
> + * @param: tpm, the chip description
> + * @param: tpm_register, the tpm tis register where the data should
> +be written
> + * @param: tpm_data, the tpm_data to write inside the tpm_register
> + * @param: tpm_size, The length of the data
> + * @return: number of byte written successfully: should be one if success.
> + */
> +static u32 SPI_WRITE_DATA(struct tpm_chip *tpm, u8 tpm_register,
> + u8 *tpm_data, u16 tpm_size) {
> + u8 value = 0;
> +
> + FUNC_ENTER();
> +
> + value = write8_reg(tpm, tpm_register, tpm_data, tpm_size);
> +
> + switch (value) {
> + case TPM_ST_SPI_OK:
> + return TPM_ST_SPI_OK;
> + case 0:
> + return 0;
> + default:
> + return -EBUSY;
> + }
> +} /* SPI_WRITE_DATA() */
> +
> +/*
> + * SPI_READ_DATA
> + * Recv byte from the TIS register according to the ST33ZP24 SPI protocol.
> + * @param: tpm, the chip description
> + * @param: tpm_register, the tpm tis register where the data should
> +be read
> + * @param: tpm_data, the TPM response
> + * @param: tpm_size, tpm TPM response size to read.
> + * @return: number of byte read successfully: should be one if success.
> + */
> +static u32 SPI_READ_DATA(struct tpm_chip *tpm, u8 tpm_register,
> + u8 *tpm_data, u16 tpm_size) {
> + u8 value = 0;
> +
> + FUNC_ENTER();
> +
> + value = read8_reg(tpm, tpm_register, tpm_data, tpm_size);
> +
> + switch (value) {
> + case TPM_ST_SPI_OK:
> + return TPM_ST_SPI_OK;
> + case 0:
> + return 0;
> + default:
> + return -EBUSY;
> + }
> +} /* SPI_READ_DATA () */
> +
> +/*
> + * clear_interruption
> + * clear the TPM interrupt register.
> + * @param: tpm, the chip description
> + */
> +static void clear_interruption(struct tpm_chip *tpm) {
> + u8 interrupt;
> + SPI_READ_DATA(tpm, TPM_INT_STATUS, &interrupt, 1);
> + /* Clear interrupts handled with TPM_EOI */
> + SPI_WRITE_DATA(tpm, TPM_INT_STATUS, &interrupt, 1);
> + SPI_READ_DATA(tpm, TPM_INT_STATUS, &interrupt, 1); } /*
> +clear_interruption() */
> +
> +/*
> + * _wait_for_interrupt_serirq_timeout
> + * @param: tpm, the chip description
> + * @param: timeout, the timeout of the interrupt
> + * @return: the status of the interruption.
> + */
> +static int _wait_for_interrupt_serirq_timeout(struct tpm_chip *chip,
> + unsigned long timeout) {
> + unsigned long status;
> + struct spi_device *client;
> + struct st33zp24_platform_data *pin_infos;
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *) chip->vendor.iobase;
> + pin_infos = client->dev.platform_data;
> +
> + status = wait_for_completion_interruptible_timeout(
> + &pin_infos->irq_detection, timeout);
> + if (status > 0)
> + enable_irq(gpio_to_irq(pin_infos->io_serirq));
> + gpio_direction_input(pin_infos->io_serirq);
> +
> + return status;
> +} /* wait_for_interrupt_serirq_timeout() */
> +
> +unsigned long wait_for_serirq_timeout(struct tpm_chip *chip, bool condition,
> + unsigned long timeout) {
> + unsigned long status = 0;
> + struct spi_device *client;
> + struct st33zp24_platform_data *pin_infos;
> +
> + client = (struct spi_device *) chip->vendor.iobase;
> + pin_infos = client->dev.platform_data;
> +
> + status = _wait_for_interrupt_serirq_timeout(chip, timeout);
> + if (!status) {
> + status = -EBUSY;
> + goto wait_end;
> + }
> + clear_interruption(chip);
> + if (condition)
> + status = 1;
> +
> +wait_end:
> + return status;
> +}
> +
> +
> +/*
> + * tpm_stm_spi_cancel, cancel is not implemented.
> + * @param: chip, the tpm chip description as specified in
> + * driver/char/tpm/tpm.h.
> + */
> +static void tpm_stm_spi_cancel(struct tpm_chip *chip) {
> + struct spi_device *client;
> + u8 data = TPM_STS_COMMAND_READY;
> + client = (struct spi_device *) chip->vendor.iobase;
> +
> + FUNC_ENTER();
> +
> + /* this causes the current command to be aborted */
> + SPI_WRITE_DATA(chip, TPM_STS, &data, 1); } /*
> +tpm_stm_spi_cancel() */
> +
> +/*
> + * tpm_stm_spi_status return the TPM_STS register
> + * @param: chip, the tpm chip description
> + * @return: the TPM_STS register value.
> + */
> +static u8 tpm_stm_spi_status(struct tpm_chip *chip) {
> + struct spi_device *client;
> + u8 data;
> + client = (struct spi_device *) chip->vendor.iobase;
> +
> + FUNC_ENTER();
> +
> + SPI_READ_DATA(chip, TPM_STS, &data, 1);
> + return data;
> +} /* tpm_stm_spi_status() */
> +
> +
> +
> +/*
> + * check_locality if the locality is active
> + * @param: chip, the tpm chip description
> + * @return: the active locality or -EACCESS.
> + */
> +static int check_locality(struct tpm_chip *chip) {
> + struct spi_device *client;
> + u8 data;
> + u8 status;
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *) chip->vendor.iobase;
> +
> + status = SPI_READ_DATA(chip, TPM_ACCESS, &data, 1);
> + if (status && (data &
> + (TPM_ACCESS_ACTIVE_LOCALITY | TPM_ACCESS_VALID)) ==
> + (TPM_ACCESS_ACTIVE_LOCALITY | TPM_ACCESS_VALID))
> + return chip->vendor.locality;
> +
> + return -EACCES;
> +} /* check_locality() */
> +
> +/*
> + * request_locality request the TPM locality
> + * @param: chip, the chip description
> + * @return: the active locality or EACCESS.
> + */
> +static int request_locality(struct tpm_chip *chip) {
> + unsigned long stop;
> + long rc;
> + u8 data;
> + struct spi_device *client;
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *) chip->vendor.iobase;
> + /* Check locality */
> + if (check_locality(chip) == chip->vendor.locality)
> + return chip->vendor.locality;
> +
> + /* Request locality */
> + data = TPM_ACCESS_REQUEST_USE;
> + rc = SPI_WRITE_DATA(chip, TPM_ACCESS, &data, 1);
> + if (rc < 0)
> + goto end;
> +
> + /* wait for burstcount */
> + if (chip->vendor.irq) {
> + rc = wait_for_serirq_timeout(chip, (check_locality
> + (chip) >= 0),
> + chip->vendor.timeout_a);
> + if (rc > 0)
> + return chip->vendor.locality;
> + } else {
> + stop = jiffies + chip->vendor.timeout_a;
> + do {
> + if (check_locality(chip) >= 0)
> + return chip->vendor.locality;
> + msleep(TPM_TIMEOUT);
> + } while (time_before(jiffies, stop));
> + }
> +end:
> + return -EACCES;
> +} /* request_locality() */
> +
> +/*
> + * release_locality release the active locality
> + * @param: chip, the tpm chip description.
> + */
> +static void release_locality(struct tpm_chip *chip) {
> + struct spi_device *client;
> + u8 data;
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *) chip->vendor.iobase;
> + data = TPM_ACCESS_ACTIVE_LOCALITY;
> + SPI_WRITE_DATA(chip, TPM_ACCESS, &data, 1); } /*
> +release_locality()*/
> +
> +/*
> + * get_burstcount return the burstcount address 0x19 0x1A
> + * @param: chip, the chip description
> + * return: the burstcount.
> + */
> +static int get_burstcount(struct tpm_chip *chip) {
> + unsigned long stop;
> + u32 burstcnt, status;
> + u8 tpm_reg, temp;
> +
> + FUNC_ENTER();
> +
> + /* wait for burstcount */
> + /* which timeout value, spec has 2 answers (c & d) */
> + stop = jiffies + chip->vendor.timeout_d;
> + do {
> + tpm_reg = TPM_STS + 1;
> + status = SPI_READ_DATA(chip, tpm_reg, &temp, 1);
> + if (status < 0)
> + goto end;
> +
> + tpm_reg = tpm_reg + 1;
> + burstcnt = temp;
> + status = SPI_READ_DATA(chip, tpm_reg, &temp, 1);
> + if (status < 0)
> + goto end;
> +
> + burstcnt |= temp << 8;
> + if (burstcnt)
> + return burstcnt;
> + msleep(TPM_TIMEOUT);
> + } while (time_before(jiffies, stop));
> +
> +end:
> + return -EBUSY;
> +} /* get_burstcount() */
> +
> +/*
> + * wait_for_stat wait for a TPM_STS value
> + * @param: chip, the tpm chip description
> + * @param: mask, the value mask to wait
> + * @param: timeout, the timeout
> + * @param: queue, the wait queue.
> + * @return: the tpm status, 0 if success, -ETIME if timeout is reached.
> + */
> +static int wait_for_stat(struct tpm_chip *chip, u8 mask, unsigned long timeout,
> + wait_queue_head_t *queue) {
> + unsigned long stop;
> + long rc;
> + u8 status;
> +
> + FUNC_ENTER();
> +
> + /* check current status */
> + status = tpm_stm_spi_status(chip);
> + if (!chip->vendor.irq && (status & mask) == mask)
> + return 0;
> +
> + if (chip->vendor.irq) {
> + rc = wait_for_serirq_timeout(chip, ((tpm_stm_spi_status
> + (chip) & mask) ==
> + mask), timeout);
> + if (rc > 0)
> + return 0;
> + } else {
> + stop = jiffies + timeout;
> + do {
> + msleep(TPM_TIMEOUT);
> + status = tpm_stm_spi_status(chip);
> + if ((status & mask) == mask)
> + return 0;
> + } while (time_before(jiffies, stop));
> + }
> + return -ETIME;
> +} /* wait_for_stat() */
> +
> +/*
> + * recv_data receive data
> + * @param: chip, the tpm chip description
> + * @param: buf, the buffer where the data are received
> + * @param: count, the number of data to receive
> + * @return: the tpm status, 0 if success, -ETIME if timeout is reached.
> + */
> +static int recv_data(struct tpm_chip *chip, u8 *buf, size_t count) {
> + u32 size = 0, burstcnt, status, len;
> + struct spi_device *client;
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *) chip->vendor.iobase;
> +
> + while (size < count &&
> + wait_for_stat(chip,
> + TPM_STS_DATA_AVAIL | TPM_STS_VALID,
> + chip->vendor.timeout_c,
> + &chip->vendor.read_queue)
> + == 0) {
> + burstcnt = get_burstcount(chip);
> + len = min_t(int, burstcnt, count - size);
> + status = SPI_READ_DATA(chip, TPM_DATA_FIFO, buf + size, len);
> + if (status < 0)
> + return status;
> +
> +
> + size += len;
> + }
> + return size;
> +}
> +
> +/*
> + * tpm_ioserirq_handler the serirq irq handler
> + * @param: irq, the tpm chip description
> + * @param: dev_id, the description of the chip
> + * @return: the status of the handler.
> + */
> +static irqreturn_t tpm_ioserirq_handler(int irq, void *dev_id) {
> + struct tpm_chip *chip = dev_id;
> + struct spi_device *client;
> + struct st33zp24_platform_data *pin_infos;
> +
> + disable_irq_nosync(irq);
> + FUNC_ENTER();
> +
> + client = (struct spi_device *) chip->vendor.iobase;
> + pin_infos = client->dev.platform_data;
> +
> + complete(&pin_infos->irq_detection);
> + return IRQ_HANDLED;
> +} /* tpm_ioserirq_handler() */
> +
> +/*
> + * tpm_stm_spi_send send TPM commands through the SPI bus.
> + * @param: chip, the tpm chip description
> + * @param: buf, the tpm command buffer
> + * @param: len, the tpm command size
> + * @return: In case of success the number of bytes sent.
> + * In other case, a < 0 value describing the issue.
> + */
> +static int tpm_stm_spi_send(struct tpm_chip *chip, unsigned char *buf,
> + size_t len) {
> + u32 ret = 0, ordinal,
> + status, burstcnt = 0, i, size = 0;
> + u8 data;
> +
> + struct spi_device *client;
> + struct st33zp24_platform_data *pin_infos;
> +
> + FUNC_ENTER();
> +
> + if (chip == NULL)
> + return -EBUSY;
> + if (len < TPM_HEADER_SIZE)
> + return -EBUSY;
> +
> + client = (struct spi_device *)chip->vendor.iobase;
> + pin_infos = client->dev.platform_data;
> +
> + ordinal = be32_to_cpu(*((__be32 *) (buf + 6)));
> +
> + ret = request_locality(chip);
> + if (ret < 0)
> + return ret;
> +
> + status = tpm_stm_spi_status(chip);
> + if ((status & TPM_STS_COMMAND_READY) == 0) {
> + tpm_stm_spi_cancel(chip);
> + if (wait_for_stat
> + (chip, TPM_STS_COMMAND_READY, chip->vendor.timeout_b,
> + &chip->vendor.int_queue) < 0) {
> + ret = -ETIME;
> + goto out_err;
> + }
> + }
> +
> + for (i = 0 ; i < len - 1 ;) {
> + burstcnt = get_burstcount(chip);
> + size = min_t(int, len - i - 1, burstcnt);
> + ret = SPI_WRITE_DATA(chip, TPM_DATA_FIFO, buf, size);
> + if (ret < 0)
> + goto out_err;
> + i += size;
> + }
> +
> + status = tpm_stm_spi_status(chip);
> + if ((status & TPM_STS_DATA_EXPECT) == 0) {
> + ret = -EIO;
> + goto out_err;
> + }
> +
> + /* write last byte */
> + SPI_WRITE_DATA(chip, TPM_DATA_FIFO, buf + len - 1, 1);
> +
> + status = tpm_stm_spi_status(chip);
> + if ((status & TPM_STS_DATA_EXPECT) != 0) {
> + ret = -EIO;
> + goto out_err;
> + }
> +
> + /* go and do it */
> + data = TPM_STS_GO;
> + ret = SPI_WRITE_DATA(chip, TPM_STS, &data, 1);
> + if (ret < 0)
> + goto out_err;
> +
> + return len;
> +out_err:
> + tpm_stm_spi_cancel(chip);
> + release_locality(chip);
> + return ret;
> +}
> +
> +/*
> + * tpm_stm_spi_recv received TPM response through the SPI bus.
> + * @param: chip, the tpm chip description
> + * @param: buf, the tpm command buffer
> + * @param: len, the tpm command size
> +* @return: In case of success the number of bytes received.
> + * In other case, a < 0 value describing the issue.
> + */
> +static int tpm_stm_spi_recv(struct tpm_chip *chip, unsigned char *buf,
> + size_t count) {
> + int size = 0;
> + int expected;
> +
> + struct spi_device *client;
> + struct st33zp24_platform_data *pin_infos;
> +
> +
> + FUNC_ENTER();
> +
> + client = (struct spi_device *)chip->vendor.iobase;
> + pin_infos = client->dev.platform_data;
> +
> +
> + if (chip == NULL)
> + return -EBUSY;
> + if (count < TPM_HEADER_SIZE) {
> + size = -EIO;
> + goto out;
> + }
> +
> + size = recv_data(chip, buf, TPM_HEADER_SIZE);
> +
> + /* read first 10 bytes, including tag, paramsize, and result */
> + if (size < TPM_HEADER_SIZE) {
> + dev_err(chip->dev, "Unable to read header\n");
> + goto out;
> + }
> +
> + expected = be32_to_cpu(*(__be32 *) (buf + 2));
> + if (expected > count) {
> + size = -EIO;
> + goto out;
> + }
> +
> + size += recv_data(chip, &buf[TPM_HEADER_SIZE],
> + expected - TPM_HEADER_SIZE);
> + if (size < expected) {
> + dev_err(chip->dev, "Unable to read remainder of result\n");
> + size = -ETIME;
> + goto out;
> + }
> +
> +out:
> + chip->vendor.cancel(chip);
> + release_locality(chip);
> + return size;
> +}
> +
> +
> +static const struct file_operations tpm_st33_spi_fops = {
> + .owner = THIS_MODULE,
> + .llseek = no_llseek,
> + .read = tpm_read,
> + .write = tpm_write,
> + .open = tpm_open,
> + .release = tpm_release,
> +};
> +
> +static DEVICE_ATTR(pubek, S_IRUGO, tpm_show_pubek, NULL); static
> +DEVICE_ATTR(pcrs, S_IRUGO, tpm_show_pcrs, NULL); static
> +DEVICE_ATTR(enabled, S_IRUGO, tpm_show_enabled, NULL); static
> +DEVICE_ATTR(active, S_IRUGO, tpm_show_active, NULL); static
> +DEVICE_ATTR(owned, S_IRUGO, tpm_show_owned, NULL); static
> +DEVICE_ATTR(temp_deactivated, S_IRUGO, tpm_show_temp_deactivated,
> +NULL); static DEVICE_ATTR(caps, S_IRUGO, tpm_show_caps_1_2, NULL);
> +static DEVICE_ATTR(cancel, S_IWUSR | S_IWGRP, NULL,
> +tpm_store_cancel);
> +
> +static struct attribute *stm_tpm_attrs[] = {
> + &dev_attr_pubek.attr,
> + &dev_attr_pcrs.attr,
> + &dev_attr_enabled.attr,
> + &dev_attr_active.attr,
> + &dev_attr_owned.attr,
> + &dev_attr_temp_deactivated.attr,
> + &dev_attr_caps.attr,
> + &dev_attr_cancel.attr, NULL,
> +};
> +
> +static struct attribute_group stm_tpm_attr_grp = {
> + .attrs = stm_tpm_attrs
> +};
> +
> +static struct tpm_vendor_specific st_spi_tpm = {
> + .send = tpm_stm_spi_send,
> + .recv = tpm_stm_spi_recv,
> + .cancel = tpm_stm_spi_cancel,
> + .status = tpm_stm_spi_status,
> + .attr_group = &stm_tpm_attr_grp,
> + .miscdev = {.fops = &tpm_st33_spi_fops,}, };
> +
> +static int evaluate_latency(struct tpm_chip *chip) {
> + int latency = 0;
> + struct spi_device *dev = (struct spi_device *) chip->vendor.iobase;
> + struct st33zp24_platform_data *platform_data = dev->dev.platform_data;
> + int status = 0;
> + u8 data;
> +
> + for (; status == 0x00 && latency < MAX_SPI_LATENCY ; latency++) {
> + platform_data->latency = latency;
> + status = SPI_READ_DATA(chip, TPM_INTF_CAPABILITY, &data, 1);
> + }
> + return latency - 1;
> +} /* evaluate_latency() */
> +
> +static int interrupts;
> +module_param(interrupts, int, 0444);
> +MODULE_PARM_DESC(interrupts, "Enable interrupts");
> +
> +static int power_mgt = 1;
> +module_param(power_mgt, int, 0444);
> +MODULE_PARM_DESC(power_mgt, "Power Management");
> +
> +/*
> + * tpm_st33_spi_probe initialize the TPM device
> + * @param: client, the spi_device drescription (TPM SPI description).
> + * @param: id, the spi_device_id struct.
> + * @return: 0 in case of success.
> + * -1 in other case.
> + */
> +static int
> +tpm_st33_spi_probe(struct spi_device *dev) {
> + u32 err;
> + u8 intmask;
> + struct tpm_chip *chip;
> + struct st33zp24_platform_data *platform_data;
> +
> + FUNC_ENTER();
> +
> + err = 0;
> +
> + /* Check SPI platform functionnalities */
> + if (dev == NULL) {
> + pr_info("dev is NULL. exiting.\n");
> + err = -ENODEV;
> + goto end;
> + }
> +
> + chip = tpm_register_hardware(&dev->dev, &st_spi_tpm);
> + if (!chip) {
> + err = -ENODEV;
> + goto end;
> + }
> +
> + /* Allocation of SPI buffers MISO and MOSI */
> + /* Size is as follow: */
> + /* Request burstcount value = 0x800 = 2048 */
> + /* + */
> + /* Response burstcount value = 0x400 = 1024 */
> + /* + */
> + /* At least: */
> + /* 1 byte for direction/locality */
> + /* 1 byte tpm tis register */
> + /* 2 bytes spi data length (for request only) */
> + /* 2 latency bytes */
> + /* 1 status byte */
> + /* = 2048 + 1024 + 7 */
> + /* We reserved 2048 + 1024 + 20 in case latency byte */
> + /* change */
> + platform_data = dev->dev.platform_data;
> + platform_data->tpm_spi_buffer[0] =
> + kmalloc((TPM_BUFSIZE + (TPM_BUFSIZE / 2) +
> + TPM_DIGEST_SIZE) * sizeof(u8), GFP_KERNEL);
> + if (platform_data->tpm_spi_buffer[0] == NULL) {
> + err = -ENOMEM;
> + goto _tpm_clean_answer;
> + }
> + platform_data->tpm_spi_buffer[1] =
> + kmalloc((TPM_BUFSIZE + (TPM_BUFSIZE / 2) +
> + TPM_DIGEST_SIZE) * sizeof(u8) , GFP_KERNEL);
> + if (platform_data->tpm_spi_buffer[1] == NULL) {
> + err = -ENOMEM;
> + goto _tpm_clean_response;
> + }
> +
> + chip->vendor.iobase = dev;
> +
> + /* Default timeouts */
> + chip->vendor.timeout_a = msecs_to_jiffies(TIS_SHORT_TIMEOUT);
> + chip->vendor.timeout_b = msecs_to_jiffies(TIS_LONG_TIMEOUT);
> + chip->vendor.timeout_c = msecs_to_jiffies(TIS_SHORT_TIMEOUT);
> + chip->vendor.timeout_d = msecs_to_jiffies(TIS_SHORT_TIMEOUT);
> + chip->vendor.locality = LOCALITY0;
> +
> + if (power_mgt) {
> + err = gpio_request(platform_data->io_lpcpd, "TPM IO_LPCPD");
> + if (err)
> + goto _gpio_init1;
> + gpio_set_value(platform_data->io_lpcpd, 1);
> + }
> +
> + platform_data->latency = evaluate_latency(chip);
> + if (platform_data->latency <= 0x00) {
> + err = -ENODEV;
> + goto _gpio_init1;
> + }
> +
> + /* Enable interrupt */
> + /* Register GPIO pin through generic Linux GPIO API */
> + if (interrupts) {
> + init_completion(&platform_data->irq_detection);
> + if (request_locality(chip) != LOCALITY0) {
> + err = -ENODEV;
> + goto _tpm_clean_response;
> + }
> + err = gpio_request(platform_data->io_serirq, "TPM IO_SERIRQ");
> + if (err)
> + goto _gpio_init2;
> +
> + /* Clear all existing */
> + clear_interruption(chip);
> + err = request_irq(gpio_to_irq(platform_data->io_serirq),
> + &tpm_ioserirq_handler,
> + IRQF_TRIGGER_HIGH | IRQF_SHARED,
> + "TPM SERIRQ management", chip);
> + if (err < 0) {
> +
> + pr_info("TPM SERIRQ signals %d not available\n",
> + gpio_to_irq(platform_data->io_serirq));
> + goto _irq_set;
> + }
> + err = SPI_READ_DATA(chip, TPM_INT_ENABLE, &intmask, 1);
> + if (err < 0)
> + goto _irq_set;
> +
> + intmask |= TPM_INTF_CMD_READY_INT
> + | TPM_INTF_FIFO_AVALAIBLE_INT
> + | TPM_INTF_WAKE_UP_READY_INT
> + | TPM_INTF_LOC4SOFTRELEASE_INT
> + | TPM_INTF_LOCALITY_CHANGE_INT
> + | TPM_INTF_STS_VALID_INT
> + | TPM_INTF_DATA_AVAIL_INT;
> +
> + err = SPI_WRITE_DATA(chip, TPM_INT_ENABLE, &intmask, 1);
> + if (err < 0)
> + goto _irq_set;
> +
> + intmask = TPM_GLOBAL_INT_ENABLE;
> + err = SPI_WRITE_DATA(chip, TPM_INT_ENABLE + 3, &intmask, 1);
> + if (err < 0)
> + goto _irq_set;
> +
> + err = SPI_READ_DATA(chip, TPM_INT_STATUS, &intmask, 1);
> + if (err < 0)
> + goto _irq_set;
> +
> + chip->vendor.irq = interrupts;
> +
> + tpm_gen_interrupt(chip);
> + }
> +
> + tpm_get_timeouts(chip);
> +
> + /* attach chip datas to client */
> + spi_set_drvdata(dev, chip);
> + platform_data->bChipF = false;
> +
> + pr_info("TPM SPI Initialized\n");
> + return 0;
> +_irq_set:
> + free_irq(gpio_to_irq(platform_data->io_serirq), chip);
> +_gpio_init2:
> + if (platform_data && interrupts)
> + gpio_free(platform_data->io_serirq);
> +_gpio_init1:
> + if (platform_data && power_mgt)
> + gpio_free(platform_data->io_lpcpd);
> +_tpm_clean_response:
> + tpm_remove_hardware(chip->dev);
> + if (platform_data->tpm_spi_buffer[1] != NULL) {
> + kfree(platform_data->tpm_spi_buffer[1]);
> + platform_data->tpm_spi_buffer[1] = NULL;
> + }
> +_tpm_clean_answer:
> + if (platform_data->tpm_spi_buffer[0] != NULL) {
> + kfree(platform_data->tpm_spi_buffer[0]);
> + platform_data->tpm_spi_buffer[0] = NULL;
> + }
> +
> + platform_data->bChipF = true;
> +end:
> + pr_info("TPM SPI initialisation fail\n");
> + return err;
> +}
> +
> +/*
> + * tpm_st33_spi_remove remove the TPM device
> + * @param: client, the spi_device drescription (TPM SPI description).
> + clear_bit(0, &chip->is_open);
> + * @return: 0 in case of success.
> + */
> +static int tpm_st33_spi_remove(struct spi_device *client) {
> + struct tpm_chip *chip = (struct tpm_chip *)spi_get_drvdata(client);
> + struct st33zp24_platform_data *pin_infos =
> + ((struct spi_device *)
> +chip->vendor.iobase)->dev.platform_data;
> +
> + FUNC_ENTER();
> +
> + if (pin_infos != NULL) {
> + gpio_free(pin_infos->io_lpcpd);
> +
> + /* Check if chip has been previously clean */
> + if (pin_infos->bChipF != true)
> + tpm_remove_hardware(chip->dev);
> + if (pin_infos->tpm_spi_buffer[1] != NULL) {
> + kfree(pin_infos->tpm_spi_buffer[1]);
> + pin_infos->tpm_spi_buffer[1] = NULL;
> + }
> + if (pin_infos->tpm_spi_buffer[0] != NULL) {
> + kfree(pin_infos->tpm_spi_buffer[0]);
> + pin_infos->tpm_spi_buffer[0] = NULL;
> + }
> + }
> +
> + return 0;
> +}
> +
> +/*
> + * tpm_st33_spi_pm_suspend suspend the TPM device
> + * Added: Work around when suspend and no tpm application is running,
> +suspend
> + * may fail because chip->data_buffer is not set (only set in
> +tpm_open in Linux
> + * TPM core)
> + * @param: client, the spi_device drescription (TPM SPI description).
> + * @param: mesg, the power management message.
> + * @return: 0 in case of success.
> + */
> +static int tpm_st33_spi_pm_suspend(struct spi_device *client,
> + pm_message_t
> +mesg) {
> + struct tpm_chip *chip =
> + (struct tpm_chip *)spi_get_drvdata(client);
> + struct st33zp24_platform_data *pin_infos =
> + ((struct spi_device *)chip->vendor.iobase)->dev.platform_data;
> + int ret = 0;
> +
> + if (power_mgt)
> + gpio_set_value(pin_infos->io_lpcpd, 0);
> + else {
> + if (chip->data_buffer == NULL)
> + chip->data_buffer = pin_infos->tpm_spi_buffer[0];
> + ret = tpm_pm_suspend(&client->dev);
> + }
> + return ret;
> +} /* tpm_st33_spi_suspend() */
> +
> +/*
> + * tpm_st33_spi_pm_resume resume the TPM device
> + * @param: spi, the spi_device drescription (TPM SPI description).
> + * @return: 0 in case of success.
> + */
> +static int tpm_st33_spi_pm_resume(struct spi_device *spi) {
> + struct tpm_chip *chip =
> + (struct tpm_chip *)spi_get_drvdata(spi);
> + struct st33zp24_platform_data *pin_infos =
> + ((struct spi_device
> +*)chip->vendor.iobase)->dev.platform_data;
> +
> + int ret = 0;
> + if (power_mgt) {
> + gpio_set_value(pin_infos->io_lpcpd, 1);
> + ret = wait_for_serirq_timeout(chip,
> + (chip->vendor.status(chip) &&
> + TPM_STS_VALID) == TPM_STS_VALID,
> + chip->vendor.timeout_b);
> + } else {
> + if (chip->data_buffer == NULL)
> + chip->data_buffer = pin_infos->tpm_spi_buffer[0];
> + ret = tpm_pm_resume(&spi->dev);
> + if (!ret)
> + tpm_do_selftest(chip);
> + }
> + return ret;
> +} /* tpm_st33_spi_pm_resume() */
> +
> +static struct spi_driver tpm_st33_spi_driver = {
> + .driver = {
> + .owner = THIS_MODULE,
> + .name = TPM_ST33_SPI,
> + },
> + .probe = tpm_st33_spi_probe,
> + .remove = tpm_st33_spi_remove,
> + .resume = tpm_st33_spi_pm_resume,
> + .suspend = tpm_st33_spi_pm_suspend, };
> +
> +/*
> + * tpm_st33_spi_init initialize driver
> + * @return: 0 if successful, else non zero value.
> + */
> +static int __init tpm_st33_spi_init(void) {
> + FUNC_ENTER();
> + return spi_register_driver(&tpm_st33_spi_driver);
> +}
> +
> +/*
> + * tpm_st33_spi_exit The kernel calls this function during unloading
> +the
> + * module or during shut down process */ static void __exit
> +tpm_st33_spi_exit(void) {
> + FUNC_ENTER();
> + spi_unregister_driver(&tpm_st33_spi_driver);
> +}
> +
> +module_init(tpm_st33_spi_init);
> +module_exit(tpm_st33_spi_exit);
> +
> +MODULE_AUTHOR("Christophe Ricard ([email protected])");
> +MODULE_DESCRIPTION("STM TPM SPI ST33 Driver");
> +MODULE_VERSION("1.2.0"); MODULE_LICENSE("GPL");
> diff --git a/drivers/char/tpm/tpm_spi_stm_st33.h
> b/drivers/char/tpm/tpm_spi_stm_st33.h
> new file mode 100644
> index 0000000..42bae6f
> --- /dev/null
> +++ b/drivers/char/tpm/tpm_spi_stm_st33.h
> @@ -0,0 +1,75 @@
> +/*
> + * STMicroelectronics TPM SPI Linux driver for TPM ST33NP18
> + * Copyright (C) 2009, 2010 STMicroelectronics
> + *
> + * This program is free software; you can redistribute it and/or
> +modify
> + * it under the terms of the GNU General Public License as published
> +by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> +along
> + * with this program; if not, write to the Free Software Foundation,
> +Inc.,
> + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
> + *
> + * STMicroelectronics version 1.2.0, Copyright (C) 2010
> + * STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
> + * This is free software, and you are welcome to redistribute it
> + * under certain conditions.
> + *
> + * @Author: Christophe RICARD [email protected]
> + *
> + * @File: tpm_spi_stm_st33.h
> + *
> + * @Date: 09/15/2010
> + */
> +#ifndef __STM_ST33_TPM_SPI_MAIN_H__
> +#define __STM_ST33_TPM_SPI_MAIN_H__
> +
> +#include <linux/pci.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/fs.h>
> +#include <linux/miscdevice.h>
> +
> +#define MINOR_NUM_SPI 224
> +
> +#define TPM_ACCESS (0x0)
> +#define TPM_STS (0x18)
> +#define TPM_HASH_END (0x20)
> +#define TPM_DATA_FIFO (0x24)
> +#define TPM_HASH_DATA (0x24)
> +#define TPM_HASH_START (0x28)
> +#define TPM_INTF_CAPABILITY (0x14)
> +#define TPM_INT_STATUS (0x10)
> +#define TPM_INT_ENABLE (0x08)
> +
> +#define TPM_DUMMY_BYTE 0x00
> +#define TPM_WRITE_DIRECTION 0x80
> +#define TPM_HEADER_SIZE 10
> +#define TPM_BUFSIZE 2048
> +
> +/* ioctl commands */
> +#define TPMIOC_CANCEL _IO('T', 0x00)
> +#define TPMIOC_TRANSMIT _IO('T', 0x01)
> +#define TPMIOC_HASH _IO('T', 0x02)
> +#define TPMIOC_CHANGELOCALITY _IO('T', 0x03)
> +
> +#define LOCALITY0 0
> +#define LOCALITY4 4
> +
> +#define TPM_ST_SPI_OK 0x5A
> +
> +
> +#define MAX_SPI_LATENCY 15
> +
> +struct st_tpm_hash_t {
> + int size;
> + u8 *data;
> +};
> +
> +#endif /* __STM_ST33_TPM_SPI_MAIN_H__ */
> diff --git a/include/linux/spi/tpm_spi_stm_st33.h
> b/include/linux/spi/tpm_spi_stm_st33.h
> new file mode 100644
> index 0000000..c233ff6
> --- /dev/null
> +++ b/include/linux/spi/tpm_spi_stm_st33.h
> @@ -0,0 +1,46 @@
> +/*
> +* STMicroelectronics TPM SPI Linux driver for TPM ST33NP18
> +* Copyright (C) 2009, 2010 STMicroelectronics
> +* Christophe RICARD [email protected]
> +* This program is free software; you can redistribute it and/or
> +modify
> +* it under the terms of the GNU General Public License as published
> +by
> +* the Free Software Foundation; either version 2 of the License, or
> +* (at your option) any later version.
> +*
> +* This program is distributed in the hope that it will be useful,
> +* but WITHOUT ANY WARRANTY; without even the implied warranty of
> +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +* GNU General Public License for more details.
> +*
> +* You should have received a copy of the GNU General Public License
> +along
> +* with this program; if not, write to the Free Software Foundation,
> +Inc.,
> +* 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
> +*
> +* STMicroelectronics version 1.2.0, Copyright (C) 2010
> +* STMicroelectronics comes with ABSOLUTELY NO WARRANTY.
> +* This is free software, and you are welcome to redistribute it
> +* under certain conditions.
> +*
> +* @File: tpm_spi_stm_st33.h
> +*
> +* @Date: 06/15/2008
> +*/
> +#ifndef __STM_ST33_TPM_SPI_H__
> +#define __STM_ST33_TPM_SPI_H__
> +
> +#include <linux/spi/spi.h>
> +
> +#define TPM_ST33_SPI "st33zp24_spi"
> +
> +#ifndef __STM_ST33_TPM_SPI_H__
> +struct st33zp24_platform_data {
> + int io_serirq;
> + int io_lpcpd;
> + int latency;
> + bool bChipF;
> + u8 *tpm_spi_buffer[2]; /* 0 Request 1 Response */
> + struct completion irq_detection; }; #endif
> +
> +#endif /* __STM_ST33_TPM_SPI_H__ */
> --
> 1.7.1
>
>
> ----------------------------------------------------------------------
> -------- Everyone hates slow websites. So do we.
> Make your web apps faster with AppDynamics Download AppDynamics Lite
> for free today:
> http://p.sf.net/sfu/appdyn_d2d_mar
> _______________________________________________
> tpmdd-devel mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/tpmdd-devel