Setup: Dell Dimension XPS T-700r
Onboard PCI Controller:
Primary IDE: empty
Secondary IDE: CD, CD-RW
Promise PDC 20262 IDE card
Primary: Quantum Fireball 30Gb
Secondary: Seagate ST330630A
Symptoms: No recent stock distribution install disk I have will boot. (RH 7.x,
MDK 8.x) The boot sequence gets all the addresses right, but dies after
printing
ide2 at 0x10f8-0x10ff,0x10f2 on irq 10
I haven't found kernel options that will cure this. The addresses printed
by the kernel are all correct, and
ide0=noautotune,ide2=noautotune
has no effect. (This has all been reported before. If someone can point
me to a FM to R, I would be eternally grateful :-)
BUT
I discovered by accident that a kernel with NO Promise support compiled
in boots just fine! The resulting system is slow - I suspect it's not
using DMA - but the system does run.
This statement applies to kernels 2.4.5, 2.4.10 and 2.4.14.
(For anyone with a similar problem who might be reading this, the
implication is that a disk built on another machine with a custom
kernel will boot when installed.)
So... anyone have any insight? I'm willing to change configuration,
test patches, provide more information, etc.
Gory details:
Kernel configuration that works (IDE stuff only):
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_BLK_DEV_IDEFLOPPY=y
CONFIG_BLK_DEV_IDESCSI=y
CONFIG_BLK_DEV_CMD640=y
CONFIG_BLK_DEV_CMD640_ENHANCED=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_BLK_DEV_ADMA=y
CONFIG_BLK_DEV_OFFBOARD=y
CONFIG_IDEDMA_PCI_AUTO=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_BLK_DEV_PIIX=y
# CONFIG_PIIX_TUNING is not set
# CONFIG_BLK_DEV_PDC202XX is not set
# CONFIG_PDC202XX_BURST is not set
# CONFIG_PDC202XX_FORCE is not set
Diffs with kernel configuration that doesn't work:
< # CONFIG_BLK_DEV_PDC202XX is not set
---
> CONFIG_BLK_DEV_PDC202XX=y
(Turning on CONFIG_PDC202XX_BURST made no difference.)
IDE related messages from successful boot (kernel with no Promise support):
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide1: BM-DMA at 0x10e8-0x10ef, BIOS settings: hdc:pio, hdd:DMA
PDC20262: IDE controller on PCI bus 00 dev 70
PCI: Found IRQ 10 for device 00:0e.0
PDC20262: chipset revision 1
PDC20262: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1080-0x1087, BIOS settings: hda:pio, hdb:pio
ide2: BM-DMA at 0x1088-0x108f, BIOS settings: hde:pio, hdf:pio
hda: QUANTUM FIREBALLP LM30.0, ATA DISK drive
hdc: _NEC DV-5700A, ATAPI CD/DVD-ROM drive
hdd: SONY CD-RW CRX140E, ATAPI CD/DVD-ROM drive
hde: ST330630A, ATA DISK drive
ide0 at 0x1400-0x1407,0x10f6 on irq 10
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0x10f8-0x10ff,0x10f2 on irq 10
hda: 58633344 sectors (30020 MB) w/1900KiB Cache, CHS=58168/16/63
hde: 59777640 sectors (30606 MB) w/2048KiB Cache, CHS=59303/16/63
ide-floppy driver 0.97.sv
Partition check:
hda: [PTBL] [3649/255/63] hda1
hde: [PTBL] [3720/255/63] hde1 hde2 hde3 hde4 < hde5 hde6 hde7 hde8 hde9 hde10 >
ide-floppy driver 0.97.sv
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: _NEC Model: DV-5700A Rev: 1.05
Type: CD-ROM ANSI SCSI revision: 02
Vendor: SONY Model: CD-RW CRX140E Rev: 1.0n
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 17x/40x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
usb.c: registered new driver usbdevfs
IDE related messages from failed boot:
PDC20262: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode
appears before
ide0: BM-DMA at 0x1080-0x1087, BIOS settings: hda:pio, hdb:pio
and the system dies after
ide2 at 0x10f8-0x10ff,0x10f2 on irq 10
hdparm -i /dev/hda
/dev/hda:
Model=QUANTUM FIREBALLP LM30.0, FwRev=A35.0700, SerialNo=186011032806
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=32256, SectSize=21298, ECCbytes=4
BuffType=DualPortCache, BuffSize=1900kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=58633344
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
AdvancedPM=no
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5
hdparm -i /dev/hde
/dev/hde:
Model=ST330630A, FwRev=3.21, SerialNo=3CK04SY4
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=59777640
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4
One final note: The RH 7.2 kernel (and maybe earlier ones, I can't remember)
puts the Promise controller at hde/f and hdg/h instead, but the net result
is the same.
Allen McIntosh wrote:
> This statement applies to kernels 2.4.5, 2.4.10 and 2.4.14.
Did you try kernel 2.4.2 ? I have another troubles on 2.4.10
with promise chip. It looks go well on 2.4.2. I think some problems
in ide-pci driver on later kernels.
--
-=-=-=-= SHINKO ELECTRIC INDUSTRIES CO., LTD. =-=-=-=-
=-=-=-=- Core Technology Research & Laboratory, -=-=-=-=
-=-=-=-= Infomation Technology Research Dept. =-=-=-=-
=-=-=-=- Name:Hisakazu Nakai TEL:026-283-2866 -=-=-=-=
-=-=-=-= Mail:[email protected] FAX:026-283-2820 =-=-=-=-
Hi,
and how about IRQ sharing? I wonder that Promise cards are little bit
selfish about their resources, because I spent a lot of time setting them up
to cooperate with rest of hardware (scsi controller, ide onboard
controllers, NIC etc.). Finally I discovered, that my Promise controller had
to have polished setup in BIOS to init&boot correctly:
1) PCI-IDE map to <PCI slot # of Promise card>
2) PCI-IRQ on <PCI slot # of Promise card> setup to some certain value, as
high as possible (not AUTO)
3)in PCI/PnP section of BIOS set this value as USED BY ISA (if I remember
well :)
4) of course setup your BIOS to "Not PnP OS (even if linux is PnP)"
I hope this can help.
Regards,
Petr
> ----- Original message follows -----
> Setup: Dell Dimension XPS T-700r
> Onboard PCI Controller:
> Primary IDE: empty
> Secondary IDE: CD, CD-RW
> Promise PDC 20262 IDE card
> Primary: Quantum Fireball 30Gb
> Secondary: Seagate ST330630A
>
> Symptoms: No recent stock distribution install disk I have will boot. (RH
> 7.x,
> MDK 8.x) The boot sequence gets all the addresses right, but dies after
> printing
> ide2 at 0x10f8-0x10ff,0x10f2 on irq 10
> I haven't found kernel options that will cure this. The addresses printed
> by the kernel are all correct, and
> ide0=noautotune,ide2=noautotune
> has no effect. (This has all been reported before. If someone can point
> me to a FM to R, I would be eternally grateful :-)
>
> BUT
>
> I discovered by accident that a kernel with NO Promise support compiled
> in boots just fine! The resulting system is slow - I suspect it's not
> using DMA - but the system does run.
> This statement applies to kernels 2.4.5, 2.4.10 and 2.4.14.
> (For anyone with a similar problem who might be reading this, the
> implication is that a disk built on another machine with a custom
> kernel will boot when installed.)
>
> So... anyone have any insight? I'm willing to change configuration,
> test patches, provide more information, etc.
>
> Gory details:
>
> Kernel configuration that works (IDE stuff only):
>
> CONFIG_IDE=y
> CONFIG_BLK_DEV_IDE=y
> CONFIG_BLK_DEV_IDEDISK=y
> CONFIG_BLK_DEV_IDEFLOPPY=y
> CONFIG_BLK_DEV_IDESCSI=y
> CONFIG_BLK_DEV_CMD640=y
> CONFIG_BLK_DEV_CMD640_ENHANCED=y
> CONFIG_BLK_DEV_IDEPCI=y
> CONFIG_IDEPCI_SHARE_IRQ=y
> CONFIG_BLK_DEV_IDEDMA_PCI=y
> CONFIG_BLK_DEV_ADMA=y
> CONFIG_BLK_DEV_OFFBOARD=y
> CONFIG_IDEDMA_PCI_AUTO=y
> CONFIG_BLK_DEV_IDEDMA=y
> CONFIG_BLK_DEV_PIIX=y
> # CONFIG_PIIX_TUNING is not set
> # CONFIG_BLK_DEV_PDC202XX is not set
> # CONFIG_PDC202XX_BURST is not set
> # CONFIG_PDC202XX_FORCE is not set
>
>
> Diffs with kernel configuration that doesn't work:
>
> < # CONFIG_BLK_DEV_PDC202XX is not set
> ---
> > CONFIG_BLK_DEV_PDC202XX=y
>
>
> (Turning on CONFIG_PDC202XX_BURST made no difference.)
>
> IDE related messages from successful boot (kernel with no Promise
> support):
>
>
> Uniform Multi-Platform E-IDE driver Revision: 6.31
> ide: Assuming 33MHz system bus speed for PIO modes; override with
> idebus=xx
> PIIX4: IDE controller on PCI bus 00 dev 39
> PIIX4: chipset revision 1
> PIIX4: not 100% native mode: will probe irqs later
> ide1: BM-DMA at 0x10e8-0x10ef, BIOS settings: hdc:pio, hdd:DMA
> PDC20262: IDE controller on PCI bus 00 dev 70
> PCI: Found IRQ 10 for device 00:0e.0
> PDC20262: chipset revision 1
> PDC20262: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0x1080-0x1087, BIOS settings: hda:pio, hdb:pio
> ide2: BM-DMA at 0x1088-0x108f, BIOS settings: hde:pio, hdf:pio
> hda: QUANTUM FIREBALLP LM30.0, ATA DISK drive
> hdc: _NEC DV-5700A, ATAPI CD/DVD-ROM drive
> hdd: SONY CD-RW CRX140E, ATAPI CD/DVD-ROM drive
> hde: ST330630A, ATA DISK drive
> ide0 at 0x1400-0x1407,0x10f6 on irq 10
> ide1 at 0x170-0x177,0x376 on irq 15
> ide2 at 0x10f8-0x10ff,0x10f2 on irq 10
> hda: 58633344 sectors (30020 MB) w/1900KiB Cache, CHS=58168/16/63
> hde: 59777640 sectors (30606 MB) w/2048KiB Cache, CHS=59303/16/63
> ide-floppy driver 0.97.sv
> Partition check:
> hda: [PTBL] [3649/255/63] hda1
> hde: [PTBL] [3720/255/63] hde1 hde2 hde3 hde4 < hde5 hde6 hde7 hde8 hde9
> hde10 >
> ide-floppy driver 0.97.sv
> SCSI subsystem driver Revision: 1.00
> scsi0 : SCSI host adapter emulation for IDE ATAPI devices
> Vendor: _NEC Model: DV-5700A Rev: 1.05
> Type: CD-ROM ANSI SCSI revision: 02
> Vendor: SONY Model: CD-RW CRX140E Rev: 1.0n
> Type: CD-ROM ANSI SCSI revision: 02
> Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
> Attached scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0
> sr0: scsi3-mmc drive: 17x/40x cd/rw xa/form2 cdda tray
> Uniform CD-ROM driver Revision: 3.12
> sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
> usb.c: registered new driver usbdevfs
>
>
> IDE related messages from failed boot:
>
> PDC20262: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode
>
> appears before
> ide0: BM-DMA at 0x1080-0x1087, BIOS settings: hda:pio, hdb:pio
> and the system dies after
> ide2 at 0x10f8-0x10ff,0x10f2 on irq 10
>
>
> hdparm -i /dev/hda
>
> /dev/hda:
>
> Model=QUANTUM FIREBALLP LM30.0, FwRev=A35.0700, SerialNo=186011032806
> Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
> RawCHS=16383/16/63, TrkSize=32256, SectSize=21298, ECCbytes=4
> BuffType=DualPortCache, BuffSize=1900kB, MaxMultSect=16, MultSect=off
> CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=58633344
> IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
> PIO modes: pio0 pio1 pio2 pio3 pio4
> DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
> AdvancedPM=no
> Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-1 ATA-2 ATA-3
> ATA-4 ATA-5
>
> hdparm -i /dev/hde
>
> /dev/hde:
>
> Model=ST330630A, FwRev=3.21, SerialNo=3CK04SY4
> Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
> RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
> BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=off
> CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=59777640
> IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
> PIO modes: pio0 pio1 pio2 pio3 pio4
> DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
> AdvancedPM=no
> Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4
>
> One final note: The RH 7.2 kernel (and maybe earlier ones, I can't
> remember)
> puts the Promise controller at hde/f and hdg/h instead, but the net result
> is the same.
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
I wrote:
> [Can't get Linux to boot with PDC20262 controller. One of disks is a
> Quantum Fireball Plus.]
Malcom Mallardi posted a note around the same time describing the same
problem. Wayne Whitney suggested that Malcom add his disk to the "problem
disk" list in pdc202xx.c, and Malcom reports that it worked. I did the
same thing for my disk, with the same results.
I enclose two patches against the 2.4.14 kernel. The first patch just adds
both problem disks to the list. The second assumes that all disks in the
appropriate Quantum families are a problem. My vote is for the second one.
Patch 1:
--- drivers/ide/pdc202xx.c.ori Wed Nov 14 18:22:27 2001
+++ drivers/ide/pdc202xx.c Wed Nov 14 20:57:13 2001
@@ -230,7 +230,9 @@
"QUANTUM FIREBALLP KA6.4",
"QUANTUM FIREBALLP LM20.4",
"QUANTUM FIREBALLP KX20.5",
+ "QUANTUM FIREBALLP KX27.3",
"QUANTUM FIREBALLP LM20.5",
+ "QUANTUM FIREBALLP LM30.0",
NULL
};
Patch 2:
--- drivers/ide/pdc202xx.c.ori Wed Nov 14 18:22:27 2001
+++ drivers/ide/pdc202xx.c Wed Nov 14 21:20:09 2001
@@ -225,12 +225,18 @@
byte pdc202xx_proc = 0;
+/*
+ * Problems have been reported with the following Quantum Fireball Plus drives:
+ * KA 6.4GB, KX 20.5GB, 27.3GB, LM 20.4GB, 20.5GB and 30.0GB. Quantum's
+ * datasheets suggest that all drives in a series (KA, KX and LM) have the
+ * same design. It seems prudent to identify them all here.
+ */
+
const char *pdc_quirk_drives[] = {
"QUANTUM FIREBALLlct08 08",
- "QUANTUM FIREBALLP KA6.4",
- "QUANTUM FIREBALLP LM20.4",
- "QUANTUM FIREBALLP KX20.5",
- "QUANTUM FIREBALLP LM20.5",
+ "QUANTUM FIREBALLP KA",
+ "QUANTUM FIREBALLP KX",
+ "QUANTUM FIREBALLP LM",
NULL
};