Hi all,
In the current code, if the rootfs is located on a SCSI device and root=
/dev/sda3 is specified as boot option in grub.cfg, kernel boots failed
with CONFIG_SCSI=y and CONFIG_BLK_DEV_SD=m when there is no initrd, here
are the boot messages via the serial console:
/dev/root: Can't open blockdev
VFS: Cannot open root device "/dev/sda3" or unknown-block(0,0): error -6
Please append a correct "root=" boot option; here are the available
partitions:
...
Kernel panic - not syncing: VFS: Unable to mount root fs on
unknown-block(0,0)
Set CONFIG_BLK_DEV_SD=y can solve the above issue, but in order to avoid
the potential failure, it is better to restrict the configs.
Here are some backgrounds according to Documentation/scsi/scsi.rst and
drivers/scsi/Kconfig:
The SCSI support in the Linux kernel can be modularized in a number of
different ways depending upon the needs of the end user.
The scsi-core (also known as the "mid level") contains the core of SCSI
support. Without it you can do nothing with any of the other SCSI drivers.
The SCSI core support can be a module, or it can be built into the kernel.
If the core is a module, it must be the first SCSI module loaded, and if
you unload the modules, it will have to be the last one unloaded.
The individual upper and lower level drivers can be loaded in any order
once the SCSI core is present in the kernel (either compiled in or loaded
as a module). The disk driver, CD-ROM driver, tape driver and SCSI generics
driver represent the upper level drivers to support the various assorted
devices which can be controlled. You can for example load the tape driver
to use the tape drive, and then unload it once you have no further need for
the driver (and release the associated memory).
However, do not compile the SCSI disk driver as a module if your root file
system is located on a SCSI device. In this case, do not compile the driver
for your SCSI host adapter as a module either.
That is to say, if you want to use an ATA hard disk as root device, config
ATA will be set as y and select CONFIG_SCSI, then CONFIG_BLK_DEV_SD should
be set as y and it can not be modified as m through the defconfig or make
menuconfig if CONFIG_SCSI is y, the simple way is to let CONFIG_SCSI select
CONFIG_BLK_DEV_SD if CONFIG_SCSI is y.
Could you please let me know are you OK with the following change?
-- >8 --
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
index 634f2f501c6c..3e59e3e59e79 100644
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -25,6 +25,7 @@ config SCSI
select SG_POOL
select SCSI_COMMON
select BLK_DEV_BSG_COMMON if BLK_DEV_BSG
+ select BLK_DEV_SD if SCSI=y
help
If you want to use a SCSI hard disk, SCSI tape drive, SCSI
CD-ROM or
any other SCSI device under Linux, say Y and make sure that
you know
If yes, I will post a formal patch later.
Thanks,
Tiezhu
On Mon, 2024-04-29 at 17:29 +0800, Tiezhu Yang wrote:
[...]
> Could you please let me know are you OK with the following change?
>
> -- >8 --
> diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
> index 634f2f501c6c..3e59e3e59e79 100644
> --- a/drivers/scsi/Kconfig
> +++ b/drivers/scsi/Kconfig
> @@ -25,6 +25,7 @@ config SCSI
> select SG_POOL
> select SCSI_COMMON
> select BLK_DEV_BSG_COMMON if BLK_DEV_BSG
> + select BLK_DEV_SD if SCSI=y
> help
> If you want to use a SCSI hard disk, SCSI tape drive, SCSI
> CD-ROM or
> any other SCSI device under Linux, say Y and make sure
> that
> you know
>
> If yes, I will post a formal patch later.
No: this is a distro config problem not a kernel one. If the distro
doesn't boot with an initrd then every module used by the boot
(including all the SCSI drivers) must be built in and the distro kernel
builder must ensure that.
James