Add support for new home automation devices.
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB LPDDR4
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB LPDDR4
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB
Changes from v2:
- add new vendor to vendor-prefixes
- sync board compatible dt-bindings to jethome,jethub-*
- fix efuse fields
- fix gpio-line-names
- fix spaces and blank lines
- recheck via checkpatch
Changes from v1:
- rearrange patches
- add SPDX license and copyright header
- remove attributes without bindings
- small fixes with spaces
Vyacheslav Bocharov (4):
dt-bindings: arm: amlogic: add bindings for Jethub D1/H1
dt-bindings: vendor-prefixes: add jethome prefix
arm64: dts: meson-gxl: add support for JetHub H1
arm64: dts: meson-axg: add support for JetHub D1
.../devicetree/bindings/arm/amlogic.yaml | 2 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
arch/arm64/boot/dts/amlogic/Makefile | 2 +
.../amlogic/meson-axg-jethome-jethub-j100.dts | 354 ++++++++++++++++++
.../meson-gxl-s905w-jethome-jethub-j80.dts | 240 ++++++++++++
5 files changed, 600 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
--
2.30.2
JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation
controller with the following features:
- square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB LPDDR4
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB
Signed-off-by: Vyacheslav Bocharov <[email protected]>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../meson-gxl-s905w-jethome-jethub-j80.dts | 241 ++++++++++++++++++
2 files changed, 241 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index faa0a79a34f5..2c3ce7c401a5 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -38,6 +38,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-libretech-pc.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-jethome-jethub-j80.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxm-khadas-vim2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxm-mecool-kiii-pro.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxm-minix-neo-u9h.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
new file mode 100644
index 000000000000..cccf483bd9e4
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
@@ -0,0 +1,241 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Vyacheslav Bocharov <[email protected]>
+ * Copyright (c) 2020 JetHome
+ * Author: Aleksandr Kazantsev <[email protected]>
+ * Author: Alexey Shevelkin <[email protected]>
+ * Author: Vyacheslav Bocharov <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "meson-gxl.dtsi"
+
+/ {
+ compatible = "jethome,jethub-j80", "amlogic,s905w", "amlogic,meson-gxl";
+ model = "JetHome JetHub J80";
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ reserved-memory {
+ linux,cma {
+ size = <0x0 0x1000000>;
+ };
+ };
+
+ aliases {
+ serial0 = &uart_AO; /* Console */
+ serial1 = &uart_A; /* Bluetooth */
+ serial2 = &uart_AO_B; /* Wireless module 1 */
+ serial3 = &uart_C; /* Wireless module 2 */
+ ethernet0 = ðmac;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ vddio_ao18: regulator-vddio_ao18 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vddio_boot: regulator-vddio_boot {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_BOOT";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi32k: wifi32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+};
+
+&efuse {
+ bt_mac: bt_mac@6 {
+ reg = <0x6 0x6>;
+ };
+
+ wifi_mac: wifi_mac@C {
+ reg = <0xc 0x6>;
+ };
+};
+
+&sn {
+ reg = <0x32 0x20>;
+};
+
+ð_mac {
+ reg = <0x0 0x6>;
+};
+
+&bid {
+ reg = <0x12 0x20>;
+};
+
+&usb {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&pwm_ef {
+ status = "okay";
+ pinctrl-0 = <&pwm_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&clkc CLKID_FCLK_DIV4>;
+ clock-names = "clkin0";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+ status = "okay";
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+
+ non-removable;
+ disable-wp;
+
+ /* WiFi firmware requires power to be kept while in suspend */
+ keep-power-in-suspend;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* Console UART */
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+/* S905W only has access to its internal PHY */
+ðmac {
+ status = "okay";
+ phy-mode = "rmii";
+ phy-handle = <&internal_phy>;
+};
+
+&internal_phy {
+ status = "okay";
+ pinctrl-0 = <ð_link_led_pins>, <ð_act_led_pins>;
+ pinctrl-names = "default";
+};
+
+&uart_A {
+ status = "okay";
+ pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+};
+
+&uart_C {
+ status = "okay";
+ pinctrl-0 = <&uart_c_pins>;
+ pinctrl-names = "default";
+};
+
+&uart_AO_B {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_b_pins>, <&uart_ao_b_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+};
+
+&i2c_B {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_b_pins>;
+
+ pcf8563: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ status = "okay";
+ };
+};
--
2.30.2
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
controller with the following features:
- DIN Rail Mounting
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB LPDDR4
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac,
Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
Signed-off-by: Vyacheslav Bocharov <[email protected]>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../amlogic/meson-axg-jethome-jethub-j100.dts | 354 ++++++++++++++++++
2 files changed, 355 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 2c3ce7c401a5..3ba6f58b9833 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -1,5 +1,6 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
new file mode 100644
index 000000000000..bc10f3357c09
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
@@ -0,0 +1,354 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Vyacheslav Bocharov <[email protected]>
+ * Copyright (c) 2020 JetHome
+ * Author: Aleksandr Kazantsev <[email protected]>
+ * Author: Alexey Shevelkin <[email protected]>
+ * Author: Vyacheslav Bocharov <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "meson-axg.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg";
+ model = "JetHome JetHub J100";
+ aliases {
+ serial0 = &uart_AO; /* Console */
+ serial1 = &uart_AO_B; /* External UART (Wireless Module) */
+ ethernet0 = ðmac;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ /* 1024MB RAM */
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ reserved-memory {
+ linux,cma {
+ size = <0x0 0x400000>;
+ };
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_5v: regulator-vcc_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_5v>;
+ regulator-always-on;
+ };
+
+ vddio_ao18: regulator-vddio_ao18 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddio_boot: regulator-vddio_boot {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_BOOT";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ usb_pwr: regulator-usb_pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "USB_PWR";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+ regulator-always-on;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+
+ wifi32k: wifi32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
+ };
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&scpi_sensors 0>;
+ trips {
+ cpu_passive: cpu-passive {
+ temperature = <70000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+
+ cpu_hot: cpu-hot {
+ temperature = <80000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "hot";
+ };
+
+ cpu_critical: cpu-critical {
+ temperature = <100000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "critical";
+ };
+ };
+ };
+
+ cpu_cooling_maps: cooling-maps {
+ map0 {
+ trip = <&cpu_passive>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+
+ map1 {
+ trip = <&cpu_hot>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+};
+
+&efuse {
+ sn: sn@32 {
+ reg = <0x32 0x20>;
+ };
+
+ eth_mac: eth_mac@0 {
+ reg = <0x0 0x6>;
+ };
+
+ bt_mac: bt_mac@6 {
+ reg = <0x6 0x6>;
+ };
+
+ wifi_mac: wifi_mac@c {
+ reg = <0xc 0x6>;
+ };
+
+ bid: bid@12 {
+ reg = <0x12 0x20>;
+ };
+};
+
+ðmac {
+ status = "okay";
+ pinctrl-0 = <ð_rmii_x_pins>;
+ pinctrl-names = "default";
+ phy-handle = <ð_phy0>;
+ phy-mode = "rmii";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
+ eth_phy0: ethernet-phy@0 {
+ /* compatible = "ethernet-phy-id0243.0c54";*/
+ max-speed = <100>;
+ reg = <0>;
+
+ reset-assert-us = <10000>;
+ reset-deassert-us = <10000>;
+ reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+/* Internal I2C bus (on CPU module) */
+&i2c1 {
+ status = "okay";
+ pinctrl-0 = <&i2c1_z_pins>;
+ pinctrl-names = "default";
+
+ /* RTC */
+ pcf8563: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ status = "okay";
+ };
+};
+
+/* Peripheral I2C bus (on motherboard) */
+&i2c_AO {
+ status = "okay";
+ pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
+ pinctrl-names = "default";
+};
+
+&pwm_ab {
+ status = "okay";
+ pinctrl-0 = <&pwm_a_x20_pins>;
+ pinctrl-names = "default";
+};
+
+/* wifi module */
+&sd_emmc_b {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ sd-uhs-sdr104;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* emmc storage */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* UART Bluetooth */
+&uart_B {
+ status = "okay";
+ pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+/* UART Console */
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+/* UART Wireless module */
+&uart_AO_B {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_b_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+ phy-supply = <&usb_pwr>;
+};
+
+&spicc1 {
+ status = "okay";
+};
+
+&gpio {
+ gpio-line-names =
+ "", "", "", "", "", // 0 - 4
+ "", "", "", "", "", // 5 - 9
+ "UserButton", "", "", "", "", // 10 - 14
+ "", "", "", "", "", // 15 - 19
+ "", "", "", "", "", // 20 - 24
+ "", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
+ "Output1", "", "", "", "", // 30 - 34
+ "", "ZigBeeBOOT", "", "", "", // 35 - 39
+ "", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
+ "Input2", "Input1", "", "", "", // 45 - 49
+ "", "", "", "", "", // 50 - 54
+ "", "", "", "", "", // 55 - 59
+ "", "", "", "", "", // 60 - 64
+ "", "", "", "", "", // 65 - 69
+ "", "", "", "", "", // 70 - 74
+ "", "", "", "", "", // 75 - 79
+ "", "", "", "", "", // 80 - 84
+ "", ""; // 85-86
+};
+
+&cpu0 {
+ #cooling-cells = <2>;
+};
+
+&cpu1 {
+ #cooling-cells = <2>;
+};
+
+&cpu2 {
+ #cooling-cells = <2>;
+};
+
+&cpu3 {
+ #cooling-cells = <2>;
+};
--
2.30.2
JetHome is trademark of IP Sokolov P.A., manufacturer of home automation
devices.
Signed-off-by: Vyacheslav Bocharov <[email protected]>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index a867f7102c35..c52f0d3261bb 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -577,6 +577,8 @@ patternProperties:
description: JEDEC Solid State Technology Association
"^jesurun,.*":
description: Shenzhen Jesurun Electronics Business Dept.
+ "^jethome,.*":
+ description: JetHome (IP Sokolov P.A.)
"^jianda,.*":
description: Jiandangjing Technology Co., Ltd.
"^kam,.*":
--
2.30.2
On 04/09/2021 16:27, Vyacheslav Bocharov wrote:
> JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
> controller with the following features:
> - DIN Rail Mounting
> - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
> - no video out
> - 512Mb/1GB LPDDR4
> - 8/16GB eMMC flash
> - 1 x USB 2.0
> - 1 x 10/100Mbps ethernet
> - WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac,
> Bluetooth 4.2.
> - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
> and Zigbee 3.0 support.
> - 2 x gpio LEDS
> - GPIO user Button
> - 1 x 1-Wire
> - 2 x RS-485
> - 4 x dry contact digital GPIO inputs
> - 3 x relay GPIO outputs
> - DC source with a voltage of 9 to 56 V / Passive POE
>
> Signed-off-by: Vyacheslav Bocharov <[email protected]>
> ---
> arch/arm64/boot/dts/amlogic/Makefile | 1 +
> .../amlogic/meson-axg-jethome-jethub-j100.dts | 354 ++++++++++++++++++
> 2 files changed, 355 insertions(+)
> create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
>
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index 2c3ce7c401a5..3ba6f58b9833 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -1,5 +1,6 @@
> # SPDX-License-Identifier: GPL-2.0
> dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> new file mode 100644
> index 000000000000..bc10f3357c09
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> @@ -0,0 +1,354 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2021 Vyacheslav Bocharov <[email protected]>
> + * Copyright (c) 2020 JetHome
> + * Author: Aleksandr Kazantsev <[email protected]>
> + * Author: Alexey Shevelkin <[email protected]>
> + * Author: Vyacheslav Bocharov <[email protected]>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-axg.dtsi"
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> + compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg";
> + model = "JetHome JetHub J100";
> + aliases {
> + serial0 = &uart_AO; /* Console */
> + serial1 = &uart_AO_B; /* External UART (Wireless Module) */
> + ethernet0 = ðmac;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + /* 1024MB RAM */
> + memory@0 {
> + device_type = "memory";
> + reg = <0x0 0x0 0x0 0x40000000>;
> + };
> +
> + reserved-memory {
> + linux,cma {
> + size = <0x0 0x400000>;
> + };
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> + };
> +
> + vcc_3v3: regulator-vcc_3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + };
> +
> + vcc_5v: regulator-vcc_5v {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC5V";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + vddao_3v3: regulator-vddao_3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDAO_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc_5v>;
> + regulator-always-on;
> + };
> +
> + vddio_ao18: regulator-vddio_ao18 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDIO_AO18";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + };
> +
> + vddio_boot: regulator-vddio_boot {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDIO_BOOT";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + };
> +
> + usb_pwr: regulator-usb_pwr {
> + compatible = "regulator-fixed";
> + regulator-name = "USB_PWR";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc_5v>;
> + regulator-always-on;
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
> + clocks = <&wifi32k>;
> + clock-names = "ext_clock";
> + };
> +
> + wifi32k: wifi32k {
> + compatible = "pwm-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
> + };
> +
> + thermal-zones {
> + cpu_thermal: cpu-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> + thermal-sensors = <&scpi_sensors 0>;
> + trips {
> + cpu_passive: cpu-passive {
> + temperature = <70000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "passive";
> + };
> +
> + cpu_hot: cpu-hot {
> + temperature = <80000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "hot";
> + };
> +
> + cpu_critical: cpu-critical {
> + temperature = <100000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "critical";
> + };
> + };
> + };
> +
> + cpu_cooling_maps: cooling-maps {
> + map0 {
> + trip = <&cpu_passive>;
> + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> +
> + map1 {
> + trip = <&cpu_hot>;
> + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +};
> +
> +&efuse {
> + sn: sn@32 {
> + reg = <0x32 0x20>;
> + };
> +
> + eth_mac: eth_mac@0 {
> + reg = <0x0 0x6>;
> + };
> +
> + bt_mac: bt_mac@6 {
> + reg = <0x6 0x6>;
> + };
> +
> + wifi_mac: wifi_mac@c {
> + reg = <0xc 0x6>;
> + };
> +
> + bid: bid@12 {
> + reg = <0x12 0x20>;
> + };
> +};
> +
> +ðmac {
> + status = "okay";
> + pinctrl-0 = <ð_rmii_x_pins>;
> + pinctrl-names = "default";
> + phy-handle = <ð_phy0>;
> + phy-mode = "rmii";
> +
> + mdio {
> + compatible = "snps,dwmac-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
> + eth_phy0: ethernet-phy@0 {
> + /* compatible = "ethernet-phy-id0243.0c54";*/
> + max-speed = <100>;
> + reg = <0>;
> +
> + reset-assert-us = <10000>;
> + reset-deassert-us = <10000>;
> + reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> +
> +/* Internal I2C bus (on CPU module) */
> +&i2c1 {
> + status = "okay";
> + pinctrl-0 = <&i2c1_z_pins>;
> + pinctrl-names = "default";
> +
> + /* RTC */
> + pcf8563: pcf8563@51 {
> + compatible = "nxp,pcf8563";
> + reg = <0x51>;
> + status = "okay";
> + };
> +};
> +
> +/* Peripheral I2C bus (on motherboard) */
> +&i2c_AO {
> + status = "okay";
> + pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&pwm_ab {
> + status = "okay";
> + pinctrl-0 = <&pwm_a_x20_pins>;
> + pinctrl-names = "default";
> +};
> +
> +/* wifi module */
> +&sd_emmc_b {
> + status = "okay";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pinctrl-0 = <&sdio_pins>;
> + pinctrl-1 = <&sdio_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + sd-uhs-sdr104;
> + max-frequency = <200000000>;
> + non-removable;
> + disable-wp;
> +
> + mmc-pwrseq = <&sdio_pwrseq>;
> +
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddio_boot>;
> +
> + brcmf: wifi@1 {
> + reg = <1>;
> + compatible = "brcm,bcm4329-fmac";
> + };
> +};
> +
> +/* emmc storage */
> +&sd_emmc_c {
> + status = "okay";
> + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
> + pinctrl-1 = <&emmc_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + max-frequency = <200000000>;
> + non-removable;
> + disable-wp;
> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> +
> + mmc-pwrseq = <&emmc_pwrseq>;
> +
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vddio_boot>;
> +};
> +
> +/* UART Bluetooth */
> +&uart_B {
> + status = "okay";
> + pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
> + pinctrl-names = "default";
> + uart-has-rtscts;
> +
> + bluetooth {
> + compatible = "brcm,bcm43438-bt";
> + shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
> + };
> +};
> +
> +/* UART Console */
> +&uart_AO {
> + status = "okay";
> + pinctrl-0 = <&uart_ao_a_pins>;
> + pinctrl-names = "default";
> +};
> +
> +/* UART Wireless module */
> +&uart_AO_B {
> + status = "okay";
> + pinctrl-0 = <&uart_ao_b_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&usb {
> + status = "okay";
> + phy-supply = <&usb_pwr>;
> +};
> +
> +&spicc1 {
> + status = "okay";
> +};
Why enabling it without pinctrl properties ?
> +
> +&gpio {
> + gpio-line-names =
> + "", "", "", "", "", // 0 - 4
> + "", "", "", "", "", // 5 - 9
> + "UserButton", "", "", "", "", // 10 - 14
> + "", "", "", "", "", // 15 - 19
> + "", "", "", "", "", // 20 - 24
> + "", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
> + "Output1", "", "", "", "", // 30 - 34
> + "", "ZigBeeBOOT", "", "", "", // 35 - 39
> + "", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
> + "Input2", "Input1", "", "", "", // 45 - 49
> + "", "", "", "", "", // 50 - 54
> + "", "", "", "", "", // 55 - 59
> + "", "", "", "", "", // 60 - 64
> + "", "", "", "", "", // 65 - 69
> + "", "", "", "", "", // 70 - 74
> + "", "", "", "", "", // 75 - 79
> + "", "", "", "", "", // 80 - 84
> + "", ""; // 85-86
> +};
> +
> +&cpu0 {
> + #cooling-cells = <2>;
> +};
> +
> +&cpu1 {
> + #cooling-cells = <2>;
> +};
> +
> +&cpu2 {
> + #cooling-cells = <2>;
> +};
> +
> +&cpu3 {
> + #cooling-cells = <2>;
> +};
>
Apart the spicc node without properties, it looks good.
Neil
On 04/09/2021 16:27, Vyacheslav Bocharov wrote:
> JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation
> controller with the following features:
>
> - square plastic case
> - Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
> - no video out
> - 1GB LPDDR4
> - 8/16GB eMMC flash
> - 2 x USB 2.0
> - 1 x 10/100Mbps ethernet
> - WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
> - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
> and Zigbee 3.0 support.
> - MicroSD 2.x/3.x/4.x DS/HS cards.
> - 1 x gpio LED
> - ADC user Button
> - DC source 5V microUSB
>
> Signed-off-by: Vyacheslav Bocharov <[email protected]>
> ---
> arch/arm64/boot/dts/amlogic/Makefile | 1 +
> .../meson-gxl-s905w-jethome-jethub-j80.dts | 241 ++++++++++++++++++
> 2 files changed, 241 insertions(+)
> create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
>
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index faa0a79a34f5..2c3ce7c401a5 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -38,6 +38,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-libretech-pc.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-jethome-jethub-j80.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-gxm-khadas-vim2.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-gxm-mecool-kiii-pro.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-gxm-minix-neo-u9h.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
> new file mode 100644
> index 000000000000..cccf483bd9e4
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
> @@ -0,0 +1,241 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2021 Vyacheslav Bocharov <[email protected]>
> + * Copyright (c) 2020 JetHome
> + * Author: Aleksandr Kazantsev <[email protected]>
> + * Author: Alexey Shevelkin <[email protected]>
> + * Author: Vyacheslav Bocharov <[email protected]>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-gxl.dtsi"
> +
> +/ {
> + compatible = "jethome,jethub-j80", "amlogic,s905w", "amlogic,meson-gxl";
> + model = "JetHome JetHub J80";
> + memory@0 {
> + device_type = "memory";
> + reg = <0x0 0x0 0x0 0x40000000>;
> + };
> +
> + reserved-memory {
> + linux,cma {
> + size = <0x0 0x1000000>;
> + };
> + };
> +
> + aliases {
> + serial0 = &uart_AO; /* Console */
> + serial1 = &uart_A; /* Bluetooth */
> + serial2 = &uart_AO_B; /* Wireless module 1 */
> + serial3 = &uart_C; /* Wireless module 2 */
> + ethernet0 = ðmac;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + vddio_ao18: regulator-vddio_ao18 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDIO_AO18";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + vddio_boot: regulator-vddio_boot {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDIO_BOOT";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + vddao_3v3: regulator-vddao_3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDAO_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + vcc_3v3: regulator-vcc_3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> + };
> +
> + wifi32k: wifi32k {
> + compatible = "pwm-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
> + clocks = <&wifi32k>;
> + clock-names = "ext_clock";
> + };
> +};
> +
> +&efuse {
> + bt_mac: bt_mac@6 {
> + reg = <0x6 0x6>;
> + };
> +
> + wifi_mac: wifi_mac@C {
> + reg = <0xc 0x6>;
> + };
> +};
> +
> +&sn {
> + reg = <0x32 0x20>;
> +};
> +
> +ð_mac {
> + reg = <0x0 0x6>;
> +};
> +
> +&bid {
> + reg = <0x12 0x20>;
> +};
> +
> +&usb {
> + status = "okay";
> + dr_mode = "host";
> +};
> +
> +&pwm_ef {
> + status = "okay";
> + pinctrl-0 = <&pwm_e_pins>;
> + pinctrl-names = "default";
> + clocks = <&clkc CLKID_FCLK_DIV4>;
> + clock-names = "clkin0";
> +};
> +
> +&saradc {
> + status = "okay";
> + vref-supply = <&vddio_ao18>;
> +};
> +
> +/* Wireless SDIO Module */
> +&sd_emmc_a {
> + status = "okay";
> + pinctrl-0 = <&sdio_pins>;
> + pinctrl-1 = <&sdio_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + max-frequency = <50000000>;
> +
> + non-removable;
> + disable-wp;
> +
> + /* WiFi firmware requires power to be kept while in suspend */
> + keep-power-in-suspend;
> +
> + mmc-pwrseq = <&sdio_pwrseq>;
> +
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddio_boot>;
> +};
> +
> +/* SD card */
> +&sd_emmc_b {
> + status = "okay";
> + pinctrl-0 = <&sdcard_pins>;
> + pinctrl-1 = <&sdcard_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + max-frequency = <50000000>;
> + disable-wp;
> +
> + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
> +
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddio_boot>;
> +};
> +
> +/* eMMC */
> +&sd_emmc_c {
> + status = "okay";
> + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
> + pinctrl-1 = <&emmc_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + max-frequency = <200000000>;
> + non-removable;
> + disable-wp;
> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> +
> + mmc-pwrseq = <&emmc_pwrseq>;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vddio_boot>;
> +};
> +
> +/* Console UART */
> +&uart_AO {
> + status = "okay";
> + pinctrl-0 = <&uart_ao_a_pins>;
> + pinctrl-names = "default";
> +};
> +
> +/* S905W only has access to its internal PHY */
> +ðmac {
> + status = "okay";
> + phy-mode = "rmii";
> + phy-handle = <&internal_phy>;
> +};
> +
> +&internal_phy {
> + status = "okay";
> + pinctrl-0 = <ð_link_led_pins>, <ð_act_led_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&uart_A {
> + status = "okay";
> + pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
> + pinctrl-names = "default";
> + uart-has-rtscts;
> +};
> +
> +&uart_C {
> + status = "okay";
> + pinctrl-0 = <&uart_c_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&uart_AO_B {
> + status = "okay";
> + pinctrl-0 = <&uart_ao_b_pins>, <&uart_ao_b_cts_rts_pins>;
> + pinctrl-names = "default";
> + uart-has-rtscts;
> +};
> +
> +&i2c_B {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c_b_pins>;
> +
> + pcf8563: pcf8563@51 {
> + compatible = "nxp,pcf8563";
> + reg = <0x51>;
> + status = "okay";
> + };
> +};
>
Looks good
Reviewed-by: Neil Armstrong <[email protected]>
Neil
06.09.2021 15:26, Neil Armstrong пишет:
> On 04/09/2021 16:27, Vyacheslav Bocharov wrote:
>> JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
>> controller with the following features:
>>
>> +
>> +&spicc1 {
>> + status = "okay";
>> +};
> Why enabling it without pinctrl properties ?
spiccwas planned for use during the development of the device, but in
fact it is not currently used. Pins exist on expand pad.
Its better to add pinctrl as below or leave spicc1 disabled?
diff --git
a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
index bc10f3357c09..ecffc90d9884 100644
--- a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
@@ -313,6 +313,8 @@ &usb {
&spicc1 {
status = "okay";
+ pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
+ pinctrl-names = "default";
};
&gpio {
--
Vyacheslav
Hi,
On 06/09/2021 17:07, Vyacheslav wrote:
> 06.09.2021 15:26, Neil Armstrong пишет:
>> On 04/09/2021 16:27, Vyacheslav Bocharov wrote:
>>> JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
>>> controller with the following features:
>>>
>>> +
>>> +&spicc1 {
>>> + status = "okay";
>>> +};
>> Why enabling it without pinctrl properties ?
>
> spiccwas planned for use during the development of the device, but in fact it is not currently used. Pins exist on expand pad.
>
> Its better to add pinctrl as below or leave spicc1 disabled?
As you want, if the HW is present and functional, usually it's enabled in the DT.
Neil
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> index bc10f3357c09..ecffc90d9884 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> @@ -313,6 +313,8 @@ &usb {
>
> &spicc1 {
> status = "okay";
> + pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
> + pinctrl-names = "default";
> };
>
> &gpio {
>
>
> --
>
> Vyacheslav
>