Stephan Maciej wrote:
> On Friday 23 January 2004 03:42, Brandon Ehle wrote:
>
>>This is on a Athlon 64 3000+ on a K8V Deluxe, 1GB RAM, Gentoo for x86_64.
>
>
> Hi,
>
> I am playing with the idea of getting exactly this HW config in the near
> future. I haven't found much user reports concerning running Linux - possibly
> Gentoo - on such a system (Athlon64 on an K8V-D mobo). Do your SATA
> controllers work, esp. when booting an AMD64 kernel? How's the rest of the
> on-board hardware behaving? Is it all working? What memory brand did you buy?
>
> Thanks a lot in advance,
>
> Stephan
>
First off, I'm only running the 2.6 kernel and haven't even tried the
2.4 kernel on this board.
The board comes with 2 software RAID SATA controllers in addition to the
PATA ones. I've only gotten one of the two SATA controllers (VIA) to
work, and I'm not using RAID (just a single 10,000RPM drive). I believe
Gentoo's gentoo-dev-sources kernel has a driver for the other controller
(Promise FastTrak 378), but I haven't tried it yet because I'm already
reaching the peak of the drive with the controller I have working. One
thing to note is that the harddrive does run about 20% slower in x86_64
kernels currently, but I'm not sure why that is.
I went with 2 matched sticks of Geil DDR433 512MB (PC-3500), but one of
the weird things about the board is that if I use the other 2 memory
slots (4 in total), the RAM will only go DDR333 instead of DDR400 (I
picked DDR433 in case I want to try overclocking someday). I'm not sure
if that's specific to this board or if all of them have that problem
(due to the onchip memory controller).
The onboard 1000MB 3COM card (sk98lin driver) is pretty typical of all
3COM cards and fails under extremely high load cases (I've never used a
3COM card that didn't fail under my high load conditions), so I'm using
a second PCI 100MB NIC (tulip driver) to talk to my high load device and
the 1GB for my Internet connection. I don't think it is the sk98lin
driver at fault because the card takes a nosedive under high load
conditions in Win2K too (reaching the theorhetical peak of the card).
I don't use the onboard sound as I have an Audigy 2 (OSS driver, ALSA
doesn't work), so I don't know anything about that. All 8 USB ports
(uhci-hcd driver) work fine. I don't have any firewire devices, but it
finds the port ok. For video I'm running a GeForce FX 5900 Ultra
(nvidia proprietary) and that works good too (using the amd640-agp driver).
Everything hardware seems to work equally well in x86 or x86_64 mode,
but I'm not running in x86_64 mode anymore because of all the userspace
problems. The only issue I ran into when going to x86_64 was needing to
turn off "Legacy USB Support" in the BIOS so I didn't have to pass
idle=poll on the command line which then stops me from getting the 3-5
second pauses when compiling or running benchmarks.
Gentoo was my choice of OS for x86_64 mode because none of the other
distributions have a decent sized package set for x86_64 yet, but I've
fallen back to debian-unstable (for better stability!) until more
packages support x86_64.
On Saturday 24 January 2004 11:39, you wrote:
> Stephan Maciej wrote:
> > On Friday 23 January 2004 03:42, Brandon Ehle wrote:
> >>This is on a Athlon 64 3000+ on a K8V Deluxe, 1GB RAM, Gentoo for x86_64.
> >
> > Hi,
> >
> > I am playing with the idea of getting exactly this HW config in the near
> > future. I haven't found much user reports concerning running Linux -
> > possibly Gentoo - on such a system (Athlon64 on an K8V-D mobo). Do your
> > SATA controllers work, esp. when booting an AMD64 kernel? How's the rest
> > of the on-board hardware behaving? Is it all working? What memory brand
> > did you buy?
> >
> > Thanks a lot in advance,
> >
> > Stephan
>
> First off, I'm only running the 2.6 kernel and haven't even tried the
> 2.4 kernel on this board.
>
> The board comes with 2 software RAID SATA controllers in addition to the
> PATA ones. I've only gotten one of the two SATA controllers (VIA) to
> work, and I'm not using RAID (just a single 10,000RPM drive). I believe
> Gentoo's gentoo-dev-sources kernel has a driver for the other controller
> (Promise FastTrak 378), but I haven't tried it yet because I'm already
I currently use an IBM/Hitachi-SATA-drive attached to the Promise-Controller
on the K8V-D without problems. I use the Promise-driver from the SATA
support. The controller is configured to work as a plain IDE-Controller.
Kernels I tried are 2.6.1 and 2.6.2-rc1-mm2.
> reaching the peak of the drive with the controller I have working. One
> thing to note is that the harddrive does run about 20% slower in x86_64
> kernels currently, but I'm not sure why that is.
Haven't tried 64bit-support yet ...
>
> I went with 2 matched sticks of Geil DDR433 512MB (PC-3500), but one of
> the weird things about the board is that if I use the other 2 memory
> slots (4 in total), the RAM will only go DDR333 instead of DDR400 (I
> picked DDR433 in case I want to try overclocking someday). I'm not sure
> if that's specific to this board or if all of them have that problem
> (due to the onchip memory controller).
>
> The onboard 1000MB 3COM card (sk98lin driver) is pretty typical of all
> 3COM cards and fails under extremely high load cases (I've never used a
> 3COM card that didn't fail under my high load conditions), so I'm using
> a second PCI 100MB NIC (tulip driver) to talk to my high load device and
> the 1GB for my Internet connection. I don't think it is the sk98lin
> driver at fault because the card takes a nosedive under high load
> conditions in Win2K too (reaching the theorhetical peak of the card).
>
> I don't use the onboard sound as I have an Audigy 2 (OSS driver, ALSA
> doesn't work), so I don't know anything about that. All 8 USB ports
> (uhci-hcd driver) work fine. I don't have any firewire devices, but it
> finds the port ok. For video I'm running a GeForce FX 5900 Ultra
> (nvidia proprietary) and that works good too (using the amd640-agp driver).
>
> Everything hardware seems to work equally well in x86 or x86_64 mode,
> but I'm not running in x86_64 mode anymore because of all the userspace
> problems. The only issue I ran into when going to x86_64 was needing to
> turn off "Legacy USB Support" in the BIOS so I didn't have to pass
> idle=poll on the command line which then stops me from getting the 3-5
> second pauses when compiling or running benchmarks.
>
> Gentoo was my choice of OS for x86_64 mode because none of the other
> distributions have a decent sized package set for x86_64 yet, but I've
> fallen back to debian-unstable (for better stability!) until more
> packages support x86_64.
>
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
--
---------------------------------------
Malte Schr?der
[email protected]
ICQ# 68121508
---------------------------------------