Hello,
I will follow the
http://www.kernel.org/pub/linux/docs/lkml/reporting-bugs.html to
describe the bug:
### [1.] One line summary of the problem:
Four PCI TV tuners based on bt878 chip in one PC crashed.
### [2.] Full description of the problem/report:
I'm runnig four XAWTVs on one screen. Screen is splited by XAWTV to two
columns and two rows [6.]. If I'm clicking randomly everywhere on all
XAWTVs with right and left mouse button, the picture (PC) freeze.
Sometimes it frozen hard (doesn't works Alt+SysRq), sometimes soft (does
works Alt-SysRq).
### [3.] Keywords (i.e., modules, networking, kernel):
kernel, modules
### [4.] Kernel version (from /proc/version):
Linux version 2.6.16-rc5 (root@livecd) (gcc version 3.4.4 (Gentoo
3.4.4-r1, ssp-3.4.4-1.0, pie-8.7.8)) #2 Mon Mar 6 15:59:18 CET 2006
### [5.] Output of Oops.. message (if applicable) with symbolic
information resolved:
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv2: OCERR @ 1ef89014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv2: OCERR @ 1ef89014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv2: OCERR @ 1ef89000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv2: OCERR @ 1ef89000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:12 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:12 watch4tv bttv2: OCERR @ 1ef89000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:12 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:12 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:12 watch4tv bttv2: OCERR @ 1ef89014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:12 watch4tv bttv3: timeout: drop=0 irq=228/1180,
risc=18ad4fdc, bits: HSYNC OFLOW
Mar 6 16:03:12 watch4tv bttv3: reset, reinitialize
Mar 6 16:03:12 watch4tv bttv3: PLL: 28636363 => 35468950 . ok
Mar 6 16:03:12 watch4tv bttv2: timeout: drop=0 irq=292/292,
risc=18b9d860, bits: HSYNC OFLOW
Mar 6 16:03:12 watch4tv bttv2: reset, reinitialize
Mar 6 16:03:12 watch4tv bttv2: PLL: 28636363 => 35468950 . ok
Mar 6 16:03:12 watch4tv bttv3: OCERR @ 1efbf01c,bits: VSYNC HSYNC OFLOW
OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf000,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf000,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf000,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: timeout: drop=0 irq=244/1207,
risc=18ba701c, bits: VSYNC HSYNC OFLOW
Mar 6 16:03:13 watch4tv bttv3: reset, reinitialize
Mar 6 16:03:13 watch4tv bttv3: PLL: 28636363 => 35468950 . ok
Mar 6 16:03:23 watch4tv Unable to handle kernel paging request at
virtual address 200001d4
Mar 6 16:03:23 watch4tv printing eip:
Mar 6 16:03:23 watch4tv c0156ac7
Mar 6 16:03:23 watch4tv *pde = 00000000
Mar 6 16:03:23 watch4tv Oops: 0000 [#1]
Mar 6 16:03:23 watch4tv Modules linked in: i915 drm ohci_hcd tuner
tvaudio bttv video_buf compat_ioctl32 i2c_algo_bit v4l2_common btcx_risc
ir_common tveeprom i2c_core videodev ehci_hcd usb_storage uhci_hcd
snd_pcm_oss snd_mixer_oss snd_seq_oss snd_seq_midi_event snd_seq
snd_seq_device snd_bt87x snd_hda_intel snd_hda_codec snd_pcm snd_timer
snd soundcore snd_page_alloc usbcore
Mar 6 16:03:23 watch4tv CPU: 0
Mar 6 16:03:23 watch4tv EIP: 0060:[<c0156ac7>] Not tainted VLI
Mar 6 16:03:23 watch4tv EFLAGS: 00013212 (2.6.16-rc5 #2)
Mar 6 16:03:23 watch4tv EIP is at poll_freewait+0x16/0x3c
Mar 6 16:03:23 watch4tv eax: de25fefc ebx: 200001bc ecx: ffffffff
edx: 200001c0
Mar 6 16:03:23 watch4tv esi: da061000 edi: 00008000 ebp: 00000000
esp: de25fea8
Mar 6 16:03:23 watch4tv ds: 007b es: 007b ss: 0068
Mar 6 16:03:23 watch4tv Process X (pid: 8946, threadinfo=de25e000
task=dea45070)
Mar 6 16:03:23 watch4tv Stack: <0>de25ff98 00000000 c0156f1c de25fefc
00000000 00000000 0000783a 00000000
Mar 6 16:03:23 watch4tv 00000000 00000000 0000000f 0000783a de53c104
de53c0e4 de53c0c4 de53c164
Mar 6 16:03:23 watch4tv de53c144 de53c124 0000000f 00000000 0000000f
c0156aed da061000 00000000
Mar 6 16:03:23 watch4tv Call Trace:
Mar 6 16:03:23 watch4tv [<c0156f1c>] do_select+0x2cc/0x2d7
Mar 6 16:03:23 watch4tv [<c0156aed>] __pollwait+0x0/0x9a
Mar 6 16:03:23 watch4tv [<c0157141>] core_sys_select+0x202/0x2b7
Mar 6 16:03:23 watch4tv [<c0157293>] sys_select+0x9d/0x161
Mar 6 16:03:23 watch4tv [<c0149137>] sys_writev+0x3b/0x96
Mar 6 16:03:23 watch4tv [<c010292b>] sysenter_past_esp+0x54/0x75
Mar 6 16:03:23 watch4tv Code: c7 00 ed 6a 15 c0 c7 40 08 00 00 00 00 c7
40 04 00 00 00 00 c3 56 53 8b 44 24 0c 8b 70 04 85 f6 74 2c 8b 5e 04 83
eb 1c 8d 53 04 <8b> 43 18 e8 24 e7 fc ff 8b 03 e8 d0 2a ff ff 8d 46 08
39 c3 77
Mar 6 16:03:23 watch4tv <6>bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:23 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:23 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:23 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:23 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:23 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:23 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:23 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:24 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:24 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:24 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:24 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:24 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:24 watch4tv bttv3: timeout: drop=0 irq=357/1364,
risc=1efbf01c, bits: HSYNC OFLOW
Mar 6 16:03:27 watch4tv bttv3: reset, reinitialize
Mar 6 16:03:27 watch4tv bttv3: PLL: 28636363 => 35468950 . ok
Mar 6 16:03:54 watch4tv SysRq : Emergency Remount R/O
### [6.] A small shell script or example program which triggers the problem:
#!/bin/bash
export LC_ALL="en_US.ISO-8859-1"
export DISPLAY=:0
X -bpp 16 -auth /var/run/xauth/A:0-DieZbc vt7 &
xhost +
sleep 2
v4l-conf -c /dev/video0 -d :0 &
v4l-conf -c /dev/video1 -d :0 &
v4l-conf -c /dev/video2 -d :0 &
v4l-conf -c /dev/video3 -d :0 &
xawtv -c /dev/video0 -geometry 639x511+0+0 -display :0 "CERN site SE17" &
xawtv -c /dev/video1 -geometry 639x511+640+0 -display :0 "CERN site SE18" &
xawtv -c /dev/video2 -geometry 639x511+0+512 -display :0 "CERN site SE19" &
xawtv -c /dev/video3 -geometry 639x511+640+512 -display :0 "CERN site
SE20" &
xset -display :0 -dpms &
xset -display :0 s noblank &
xset -display :0 s noexpose &
xset -display :0 s off &
xset -display :0 s 0 0 &
### [7.] Environment:
### [7.1.] Software (add the output of the ver_linux script here):
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux watch4tv 2.6.16-rc5 #2 Mon Mar 6 15:59:18 CET 2006 i686 Intel(R)
Celeron(R) CPU 2.80GHz GenuineIntel GNU/Linux
Gnu C 3.4.4
Gnu make 3.80
binutils 2.16.1
util-linux 2.12r
mount 2.12r
module-init-tools 3.2.1
e2fsprogs 1.38
reiserfsprogs 3.6.19
reiser4progs line
Linux C Library 2.3.5
Dynamic linker (ldd) 2.3.5
Procps 3.2.5
Net-tools 1.60
Kbd 1.12
Sh-utils 5.2.1
udev 079
Modules Loaded nls_cp850 i915 drm ohci_hcd tuner tvaudio bttv
video_buf compat_ioctl32 i2c_algo_bit v4l2_common btcx_risc ir_common
tveeprom i2c_core videodev ehci_hcd usb_storage uhci_hcd snd_pcm_oss
snd_mixer_oss snd_seq_oss snd_seq_midi_event snd_seq snd_seq_device
snd_bt87x snd_hda_intel snd_hda_codec snd_pcm snd_timer snd soundcore
snd_page_alloc usbcore
### [7.2.] Processor information (from /proc/cpuinfo):
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 4
model name : Intel(R) Celeron(R) CPU 2.80GHz
stepping : 1
cpu MHz : 2800.604
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 5
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx
constant_tsc pni monitor ds_cpl tm2 cid xtpr
bogomips : 5611.80
### [7.3.] Module information (from /proc/modules):
nls_cp850 4736 1 - Live 0xe0505000
i915 15744 1 - Live 0xe04d9000
drm 53652 2 i915, Live 0xe04e5000
ohci_hcd 16132 0 - Live 0xe048a000
tuner 44460 0 - Live 0xe048f000
tvaudio 19996 0 - Live 0xe0475000
bttv 150900 4 - Live 0xe04a4000
video_buf 15364 1 bttv, Live 0xe047b000
compat_ioctl32 1152 1 bttv, Live 0xe043c000
i2c_algo_bit 7432 1 bttv, Live 0xe0472000
v4l2_common 6528 2 tuner,bttv, Live 0xe0447000
btcx_risc 3720 1 bttv, Live 0xe0078000
ir_common 7812 1 bttv, Live 0xe041e000
tveeprom 12176 1 bttv, Live 0xe046e000
i2c_core 15248 5 tuner,tvaudio,bttv,i2c_algo_bit,tveeprom, Live 0xe0442000
videodev 6656 5 bttv, Live 0xe0421000
ehci_hcd 23560 0 - Live 0xe0467000
usb_storage 29316 1 - Live 0xe045e000
uhci_hcd 25872 0 - Live 0xe0456000
snd_pcm_oss 40992 0 - Live 0xe044a000
snd_mixer_oss 14080 1 snd_pcm_oss, Live 0xe0424000
snd_seq_oss 26112 0 - Live 0xe0434000
snd_seq_midi_event 5504 1 snd_seq_oss, Live 0xe041b000
snd_seq 40016 4 snd_seq_oss,snd_seq_midi_event, Live 0xe0429000
snd_seq_device 6284 2 snd_seq_oss,snd_seq, Live 0xe00fb000
snd_bt87x 10824 0 - Live 0xe004d000
snd_hda_intel 12688 0 - Live 0xe006f000
snd_hda_codec 111616 1 snd_hda_intel, Live 0xe0317000
snd_pcm 66952 4 snd_pcm_oss,snd_bt87x,snd_hda_intel,snd_hda_codec, Live
0xe0305000
snd_timer 17540 2 snd_seq,snd_pcm, Live 0xe005e000
snd 39140 10
snd_pcm_oss,snd_mixer_oss,snd_seq_oss,snd_seq,snd_seq_device,snd_bt87x,snd_hda_intel,snd_hda_codec,snd_pcm,snd_timer,
Live 0xe0064000
soundcore 6624 1 snd, Live 0xe0054000
snd_page_alloc 7688 3 snd_bt87x,snd_hda_intel,snd_pcm, Live 0xe0051000
usbcore 97668 5 ohci_hcd,ehci_hcd,usb_storage,uhci_hcd, Live 0xe00c1000
### [7.4.] Loaded driver and hardware information (/proc/ioports,
/proc/iomem):
## /proc/ioports:
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
01f0-01f7 : ide0
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial
0400-0403 : PM1a_EVT_BLK
0404-0405 : PM1a_CNT_BLK
0408-040b : PM_TMR
0410-0415 : ACPI CPU throttle
0420-0420 : PM2_CNT_BLK
0428-042f : GPE0_BLK
0500-053f : pnp 00:0c
0680-06ff : pnp 00:0c
c400-c41f : 0000:00:1f.3
c800-c81f : 0000:00:1d.0
c800-c81f : uhci_hcd
cc00-cc1f : 0000:00:1d.1
cc00-cc1f : uhci_hcd
d000-d01f : 0000:00:1d.2
d000-d01f : uhci_hcd
d400-d41f : 0000:00:1d.3
d400-d41f : uhci_hcd
d800-d80f : 0000:00:1f.2
d800-d80f : libata
dc00-dc03 : 0000:00:1f.2
dc00-dc03 : libata
e000-e007 : 0000:00:1f.2
e000-e007 : libata
e400-e403 : 0000:00:1f.2
e400-e403 : libata
e800-e807 : 0000:00:1f.2
e800-e807 : libata
ec00-ec07 : 0000:00:02.0
ffa0-ffaf : 0000:00:1f.1
ffa0-ffa7 : ide0
ffa8-ffaf : ide1
## /proc/iomem:
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000f0000-000fffff : System ROM
00100000-1f72fbff : System RAM
00100000-002cb992 : Kernel code
002cb993-00380453 : Kernel data
1f72fc00-1f72ffff : ACPI Non-volatile Storage
1f730000-1f73ffff : ACPI Tables
1f740000-1f7effff : ACPI Non-volatile Storage
1f7f0000-1f7fffff : reserved
c0000000-cfffffff : 0000:00:02.0
d0000000-d00fffff : PCI Bus #01
d0100000-d01fffff : PCI Bus #02
d0200000-d02fffff : PCI Bus #03
d0300000-d03fffff : PCI Bus #04
d0400000-d04fffff : PCI Bus #05
d0500000-d05fffff : PCI Bus #06
d0500000-d0500fff : 0000:06:00.1
d0500000-d0500fff : Bt87x audio
d0501000-d0501fff : 0000:06:00.0
d0501000-d0501fff : bttv0
d0502000-d0502fff : 0000:06:01.1
d0502000-d0502fff : Bt87x audio
d0503000-d0503fff : 0000:06:01.0
d0503000-d0503fff : bttv1
d0504000-d0504fff : 0000:06:02.1
d0504000-d0504fff : Bt87x audio
d0505000-d0505fff : 0000:06:02.0
d0505000-d0505fff : bttv2
d0506000-d0506fff : 0000:06:03.1
d0506000-d0506fff : Bt87x audio
d0507000-d0507fff : 0000:06:03.0
d0507000-d0507fff : bttv3
e0000000-efffffff : reserved
fed13000-fed19fff : reserved
fed1c000-fed9ffff : reserved
ff400000-ff4fffff : PCI Bus #01
ff500000-ff5fffff : PCI Bus #02
ff600000-ff6fffff : PCI Bus #03
ff700000-ff7fffff : PCI Bus #04
ff800000-ff8fffff : PCI Bus #05
ff900000-ff9fffff : PCI Bus #06
ffa00000-ffa7ffff : 0000:00:02.0
ffa80000-ffabffff : 0000:00:02.0
ffac0000-ffac3fff : 0000:00:1b.0
ffac0000-ffac3fff : ICH HD audio
ffac4000-ffac43ff : 0000:00:1d.7
ffac4000-ffac43ff : ehci_hcd
[7.5.] PCI information ('lspci -vvv' as root):
00:00.0 Host bridge: Intel Corporation 915G/P/GV/GL/PL/910GL Processor
to I/O Controller (rev 04)
Subsystem: Intel Corporation Unknown device 4156
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:01.0 PCI bridge: Intel Corporation 915G/P/GV/GL/PL/910GL PCI Express
Root Port (rev 04) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: ff400000-ff4fffff
Prefetchable memory behind bridge: d0000000-d00fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [88] #0d [0000]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: 64bit-
Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [a0] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug-
Surpise-
Slot: Number 0, PowerLimit 75.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Virtual Channel
Capabilities: [140] Unknown (5)
00:02.0 VGA compatible controller: Intel Corporation 82915G/GV/910GL
Express Chipset Family Graphics Controller (rev 04) (prog-if 00 [VGA])
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ffa00000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at ec00 [size=8]
Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at ffa80000 (32-bit, non-prefetchable) [size=256K]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1b.0 Class 0403: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) High Definition Audio Controller (rev 03)
Subsystem: Intel Corporation Unknown device e203
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ffac0000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown,
Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: ff800000-ff8fffff
Prefetchable memory behind bridge: 00000000d0400000-00000000d0400000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag+
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise+
Slot: Number 1, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit-
Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.1 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) PCI Express Port 2 (rev 03) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: ff700000-ff7fffff
Prefetchable memory behind bridge: 00000000d0300000-00000000d0300000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag+
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise+
Slot: Number 2, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit-
Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.2 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) PCI Express Port 3 (rev 03) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: ff600000-ff6fffff
Prefetchable memory behind bridge: 00000000d0200000-00000000d0200000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag+
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 3
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise+
Slot: Number 3, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit-
Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.3 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: ff500000-ff5fffff
Prefetchable memory behind bridge: 00000000d0100000-00000000d0100000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag+
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 4
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise+
Slot: Number 4, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit-
Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 4: I/O ports at c800 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at cc00 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at d000 [size=32]
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at d400 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Unknown device 4156
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: Memory at ffac4000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d3) (prog-if
01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=06, subordinate=06, sec-latency=128
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: ff900000-ff9fffff
Prefetchable memory behind bridge: 00000000d0500000-00000000d0500000
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] #0d [0000]
00:1f.0 ISA bridge: Intel Corporation 82801FB/FR (ICH6/ICH6R) LPC
Interface Bridge (rev 03)
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at ffa0 [size=16]
00:1f.2 IDE interface: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA
Controller (rev 03) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at e800 [size=8]
Region 1: I/O ports at e400 [size=4]
Region 2: I/O ports at e000 [size=8]
Region 3: I/O ports at dc00 [size=4]
Region 4: I/O ports at d800 [size=16]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family)
SMBus Controller (rev 03)
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at c400 [size=32]
06:00.0 Multimedia video controller: Brooktree Corporation Bt878 Video
Capture (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0501000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:00.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture
(rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0500000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:01.0 Multimedia video controller: Brooktree Corporation Bt878 Video
Capture (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at d0503000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:01.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture
(rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at d0502000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:02.0 Multimedia video controller: Brooktree Corporation Bt878 Video
Capture (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d0505000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:02.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture
(rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d0504000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:03.0 Multimedia video controller: Brooktree Corporation Bt878 Video
Capture (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d0507000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:03.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture
(rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d0506000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
### [7.6.] SCSI information (from /proc/scsi/scsi):
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: ATA Model: WDC WD800JD-22LS Rev: 06.0
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi3 Channel: 00 Id: 00 Lun: 00
Vendor: Generic Model: USB Flash Disk Rev: 0.00
Type: Direct-Access ANSI SCSI revision: 02
### [7.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you think to be
relevant):
## modprobe.conf:
alias char-major-81 videodev
alias char-major-8-0 bttv
alias char-major-8-1 bttv
alias char-major-8-2 bttv
alias char-major-8-3 bttv
options bttv card=10 tuner=41
### [8] Other notes, patches, fixes, workarounds:
* Mainboard: Intel D945GNT (945 chipset) - I have tryed it also with
Intel D915GAV. All four PCI slots are used for TV tuners. AGP slot is
unused (graphics card is on the board).
# Power supply: Chieftec 400W
# Memory: Kingston 512MB
# HDD: Western Digital SATA 80GB
# TV Tuner: 4x Hauppauge WinTV Express (chip bt878)
* I have tryed vanilla kernel 2.6.15.1 and 2.6.16-rc5 (with / without
PREEMPT, acpi=on / acpi=off).
* I have tryed insmod options from
Documents/video4linux/bttv/Insmod-options.
* I have tryed Xorg 6.9 and Xorg 6.8.2 (with / without DRI support -
Xorg driver i810).
* I have tryed XAWTV 3.94 and XAWTV 3.95.
* I have tryed Gentoo Linux distribution and Scientific Linux CERN 4
(based on RHEL4).
* I have tryed change BIOS options: Plug&Play Enabled/Disabled, PCI IRQ
Auto/Manual.
*** always the same.
If somebody know how to solve it, I will be very appreciative. I have
tryed everything what I know, nothing helps.
Best Regards,
Jiri Tyr
> ### [1.] One line summary of the problem:
> Four PCI TV tuners based on bt878 chip in one PC crashed.
Are you using overlay, or grabdisplay?
Ciao,
Duncan.
Duncan Sands wrote:
>>### [1.] One line summary of the problem:
>>Four PCI TV tuners based on bt878 chip in one PC crashed.
>>
>>
>
>Are you using overlay, or grabdisplay?
>
>
I'm using overlay on all tuners.
Jiri
Michel Bardiaux wrote:
> I was never able to make 4 bttv work together. There is every
> probability of interrupt conflicts (but you didnt post proc/interrupts
> and its hard reading lspci), and I seriously doubt the bus would let one
> grab 4 sources full-size full-rate without losing frames and interrupts
> here and there.
Here is my /proc/interrupts:
CPU0
0: 9332 IO-APIC-edge timer
1: 144 IO-APIC-edge i8042
2: 0 XT-PIC cascade
12: 93 IO-APIC-edge i8042
18: 9332 IO-APIC-level bttv2
19: 9332 IO-APIC-level libata, bttv3
21: 9332 IO-APIC-level bttv0
22: 9332 IO-APIC-level bttv1
NMI: 0
LOC: 9294
ERR: 0
MIS: 0
I have removed all unnecessary things from kernel. Libata I need for
SATA disk. Do you think that is some possibility how to make this four
bttv tuners working?
Jiri
Stefan de Konink wrote:
>>I have removed all unnecessary things from kernel. Libata I need for
>>SATA disk. Do you think that is some possibility how to make this four
>>bttv tuners working?
>>
>What is your CONFIG_HZ setting? (100/250/1000 Hz)
>
>
I'm using CONFIG_HZ=250. I have tryed also CONFIG_HZ=100, but it didn't
helped.
Ihave tryed to remove one of the four tuners and now I have no shared
IRQ, but the PC still freeze. It is bug in DMA or whats wrong?
Jiri
Michel Bardiaux wrote:
>I dont see anything suspicious conflict. But 'overlay' has been
>mentionned, I'm not familiar with that but I assume it means you're
>doing video grabs directly to the X display, right?
Yes, I'm using xawtv + overlay directly to the X display :0.0. Is better
way to use it with some WM (KDE, Gnome, ...)?
>Then it could be a problem with the graphics card or its driver.
On the mainboard is graphics card Intel 915. I have tryed it with i810
(with / without DRI) and vesa driver. I have also tryed PCIE graphics
card from ATI. In all of those cases the PC freeze and as well as if is
in PCI slot only ONE tuner!
>Just my 2 cents, because I am totally unfamiliar with such uses, sounds
>like a problem for the MythTV crowd.
I'm totally lost! I have here 25 PCs (100 tuners) what always freeze ;o(
Jiri
On Tuesday 7 March 2006 12:50, Jiri Tyr wrote:
> Michel Bardiaux wrote:
>
> >I dont see anything suspicious conflict. But 'overlay' has been
> >mentionned, I'm not familiar with that but I assume it means you're
> >doing video grabs directly to the X display, right?
>
> Yes, I'm using xawtv + overlay directly to the X display :0.0. Is better
> way to use it with some WM (KDE, Gnome, ...)?
>
> >Then it could be a problem with the graphics card or its driver.
>
> On the mainboard is graphics card Intel 915. I have tryed it with i810
> (with / without DRI) and vesa driver. I have also tryed PCIE graphics
> card from ATI. In all of those cases the PC freeze and as well as if is
> in PCI slot only ONE tuner!
>
> >Just my 2 cents, because I am totally unfamiliar with such uses, sounds
> >like a problem for the MythTV crowd.
>
> I'm totally lost! I have here 25 PCs (100 tuners) what always freeze ;o(
Try using grabdisplay. Also, if you hook up a serial console you may see
some helpful output when the pc freezes.
Ciao,
Duncan.
Jiri Tyr wrote:
> Michel Bardiaux wrote:
>
> >I dont see anything suspicious conflict. But 'overlay' has been
> >mentionned, I'm not familiar with that but I assume it means you're
> >doing video grabs directly to the X display, right?
>
> Yes, I'm using xawtv + overlay directly to the X display :0.0. Is better
> way to use it with some WM (KDE, Gnome, ...)?
>
> >Then it could be a problem with the graphics card or its driver.
>
> On the mainboard is graphics card Intel 915. I have tryed it with i810
> (with / without DRI) and vesa driver. I have also tryed PCIE graphics
> card from ATI. In all of those cases the PC freeze and as well as if is
> in PCI slot only ONE tuner!
>
> >Just my 2 cents, because I am totally unfamiliar with such uses, sounds
> >like a problem for the MythTV crowd.
>
> I'm totally lost! I have here 25 PCs (100 tuners) what always freeze ;o(
FWIW, I have a box (with only one bttv card) which does not work stable
neither due to the capture card. It DID run stable at one point, but I
think that was kernel 2.2-ish... I tried quite a few things, IIRC when
it did run stable I had to tweak pci latency timer in the bios, but this
no longer works. Tried kernels with/without apic, acpi, smp,...
I also get the same OCERR error messages, and very similar oops. Though
it usually locks up only once every few hours or even days. Sometimes
hard and sometimes soft lockups.
The bttv driver/chip seems to cause random memory corruption sometimes,
processes will just start dying... My guess is that somehow dma
transfers to random / wrong addresses happens when there are lost irqs /
pci bus contention, either due to a driver bug or a chip bug (something
like losing parts of the risc program) though if there is a chip bug,
that behaviour never happened with some other OS so a workaround should
be possible), but I could be ways off.
This was with a i440bx chipset btw, it runs just fine with a newer box
(though overlay had problems there too, but since the box is faster I'm
just using grabdisplay, which didn't do anything for stability on the
old box). Tried both a bt848 and bt878 card which didn't change anything.
Roland
> The bttv driver/chip seems to cause random memory corruption sometimes,
> processes will just start dying...
There is a known buffer overflow in the bttv driver (when using
grabdisplay). The fix is waiting on an audit of the rest of the
bttv (and similar) code, since it looks like the same mistake
occurs in several places.
Ciao,
D.
Duncan Sands <[email protected]> wrote:
>> The bttv driver/chip seems to cause random memory corruption sometimes,
>> processes will just start dying...
>
> There is a known buffer overflow in the bttv driver (when using
> grabdisplay). The fix is waiting on an audit of the rest of the
> bttv (and similar) code, since it looks like the same mistake
> occurs in several places.
Can you give me a hint on where exactly to shoot at? I'n still hoping it's
not my VIA board giving me trouble (corrupting the first four bytes of a
semi-random page).
--
Ich danke GMX daf?r, die Verwendung meiner Adressen mittels per SPF
verbreiteten L?gen zu sabotieren.
On Sat, Mar 11, 2006 at 11:08:25AM +0100, Bodo Eggert wrote:
> Duncan Sands <[email protected]> wrote:
>
> >> The bttv driver/chip seems to cause random memory corruption sometimes,
> >> processes will just start dying...
> >
> > There is a known buffer overflow in the bttv driver (when using
> > grabdisplay). The fix is waiting on an audit of the rest of the
> > bttv (and similar) code, since it looks like the same mistake
> > occurs in several places.
>
> Can you give me a hint on where exactly to shoot at? I'n still hoping it's
> not my VIA board giving me trouble (corrupting the first four bytes of a
> semi-random page).
check out this email to LKML
it might not be the Final Fix, but xawtv hasn't crashed on me yet
From: Duncan Sands <[email protected]>
Subject: [PATCH] bttv: correct bttv_risc_packed buffer size
Date: Wed, 25 Jan 2006 11:24:27 +0100
Cc: Linux Kernel list <[email protected]>
MIME-Version: 1.0
Content-Type: Multipart/Mixed;
boundary="Boundary-00=_cH11D22lqYSaiQl"
Message-Id: <[email protected]>
--Boundary-00=_cH11D22lqYSaiQl
Content-Type: text/plain;
charset="us-ascii"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
This patch fixes the strange crashes I was seeing after using
my bttv card to watch television. They were caused by a
buffer overflow in bttv_risc_packed.
The instruction buffer size calculation contains two errors:
(a) a non-zero padding value can push the start of the next bpl
section to just before a page border, leading to more scanline
splits and thus additional instructions.
(b) the first DMA region can be smaller than one page, so there can
be a scanline split even if bpl*lines is smaller than PAGE_SIZE.
For example, consider the case where offset is 0, bpl is 2, padding
is 4094, lines is smaller than 2048, the first DMA region has size 1
and all others have size PAGE_SIZE, assumed to equal 4096. Then
all bpl regions cross page borders and the number of instructions
written is 2*lines+2, rather than lines+2 (the current estimate).
With this patch the number of instructions for this example is
estimated to be 2*lines+3.
Also, the BUG_ON that was supposed to catch buffer overflows contained
a thinko causing it fire only if the buffer was overrun by a factor of
16 or more.
I didn't check whether similar mistakes exist elsewhere in the bttv
code.
Signed-off-by: Duncan Sands <[email protected]>
PS: I'm sending the patch as an attachment because for some reason my
mailer crashes if I try to insert it into the email.
--Boundary-00=_cH11D22lqYSaiQl
Content-Type: text/x-diff;
charset="us-ascii";
name="bttv"
Content-Transfer-Encoding: 7bit
Content-Disposition: attachment;
filename="bttv"
Index: Linux/drivers/media/video/bttv-risc.c
===================================================================
--- Linux.orig/drivers/media/video/bttv-risc.c 2006-01-24 10:09:21.000000000 +0100
+++ Linux/drivers/media/video/bttv-risc.c 2006-01-24 10:16:06.000000000 +0100
@@ -51,8 +51,10 @@
int rc;
/* estimate risc mem: worst case is one write per page border +
- one write per scan line + sync + jump (all 2 dwords) */
- instructions = (bpl * lines) / PAGE_SIZE + lines;
+ one write per scan line + sync + jump (all 2 dwords). padding
+ can cause next bpl to start close to a page border. First DMA
+ region may be smaller than PAGE_SIZE */
+ instructions = 1 + ((bpl + padding) * lines) / PAGE_SIZE + lines;
instructions += 2;
if ((rc = btcx_riscmem_alloc(btv->c.pci,risc,instructions*8)) < 0)
return rc;
@@ -104,7 +106,7 @@
/* save pointer to jmp instruction address */
risc->jmp = rp;
- BUG_ON((risc->jmp - risc->cpu + 2) / 4 > risc->size);
+ BUG_ON(4 * (risc->jmp - risc->cpu + 2) > risc->size);
return 0;
}
--Boundary-00=_cH11D22lqYSaiQl--
--
Hi,
I think, it's problem in XAWTV, because I've got the same error if I
had only one TV tuner in my PC. I've solved the problem that I reduced
number of items in channel list. If I have in the list only 10
channels, then any of the four XAWTV didn't crashed. It's very
strange. It looks like the pop-up menu with the channel list write to
the memory of the graphics card somewhere out of the memory. What do
you think about it?
Jiri
Sami Farin wrote:
>On Sat, Mar 11, 2006 at 11:08:25AM +0100, Bodo Eggert wrote:
>> Duncan Sands <[email protected]> wrote:
>>
>> >> The bttv driver/chip seems to cause random memory corruption
sometimes,
>> >> processes will just start dying...
>> >
>> > There is a known buffer overflow in the bttv driver (when using
>> > grabdisplay). The fix is waiting on an audit of the rest of the
>> > bttv (and similar) code, since it looks like the same mistake
>> > occurs in several places.
>>
>> Can you give me a hint on where exactly to shoot at? I'n still
hoping it's
>> not my VIA board giving me trouble (corrupting the first four bytes of a
>> semi-random page).
>
>check out this email to LKML
>
>it might not be the Final Fix, but xawtv hasn't crashed on me yet
>
>From: Duncan Sands <[email protected]>
>Subject: [PATCH] bttv: correct bttv_risc_packed buffer size
>Date: Wed, 25 Jan 2006 11:24:27 +0100
>Cc: Linux Kernel list <[email protected]>
>MIME-Version: 1.0
>Content-Type: Multipart/Mixed;
> boundary="Boundary-00=_cH11D22lqYSaiQl"
>Message-Id: <[email protected]>
>
>
>This patch fixes the strange crashes I was seeing after using
>my bttv card to watch television. They were caused by a
>buffer overflow in bttv_risc_packed.
>
>The instruction buffer size calculation contains two errors:
>(a) a non-zero padding value can push the start of the next bpl
>section to just before a page border, leading to more scanline
>splits and thus additional instructions.
>(b) the first DMA region can be smaller than one page, so there can
>be a scanline split even if bpl*lines is smaller than PAGE_SIZE.
>
>For example, consider the case where offset is 0, bpl is 2, padding
>is 4094, lines is smaller than 2048, the first DMA region has size 1
>and all others have size PAGE_SIZE, assumed to equal 4096. Then
>all bpl regions cross page borders and the number of instructions
>written is 2*lines+2, rather than lines+2 (the current estimate).
>With this patch the number of instructions for this example is
>estimated to be 2*lines+3.
>
>Also, the BUG_ON that was supposed to catch buffer overflows contained
>a thinko causing it fire only if the buffer was overrun by a factor of
>16 or more.
>
>I didn't check whether similar mistakes exist elsewhere in the bttv
>code.
>
>Signed-off-by: Duncan Sands <[email protected]>
>
>PS: I'm sending the patch as an attachment because for some reason my
>mailer crashes if I try to insert it into the email.
On Wed, Mar 15, 2006 at 09:48:45AM +0100, Jiri Tyr wrote:
> Hi,
>
> I think, it's problem in XAWTV, because I've got the same error if I
> had only one TV tuner in my PC. I've solved the problem that I reduced
> number of items in channel list. If I have in the list only 10
> channels, then any of the four XAWTV didn't crashed. It's very
> strange. It looks like the pop-up menu with the channel list write to
> the memory of the graphics card somewhere out of the memory. What do
> you think about it?
I didn't change xawtv configs, and
1) with the patch system did not crash
2) without the patch system crashed
draw your own conclusions.
and
3) if xawtv is able to crash kernel, kernel needs fixing.
--
Sami Farin wrote:
>I didn't change xawtv configs, and
>1) with the patch system did not crash
>2) without the patch system crashed
>
>draw your own conclusions.
>
>
OK, I will wait for the change in the kernel.
>and
>3) if xawtv is able to crash kernel, kernel needs fixing.
>
>
It is strange, but manipulation with the channel list (longer then 15
items) in XAWTV made not only solide lock of the kernel, but also
sometimes only crash of the USB driver or PS2 keyboard driver. I think
there is (was - not with your patch?) something wrong in the kernel.
Maybe some memory problem.
Jiri
Sami Farin wrote:
>I didn't change xawtv configs, and
>1) with the patch system did not crash
>2) without the patch system crashed
>
>
I've tryed to apply your patch and tested it and I've got the same
result like without your patch - by manipulation with the XAWTV channel
list the PC crashed and I've got in the /var/log/message this:
bttv3: OCERR @ 1c98c000,bits: HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c000,bits: HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c000,bits: HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c014,bits: HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c014,bits: HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c014,bits: HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c000,bits: HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c000,bits: HSYNC OFLOW OCERR*
OCERR @ 1c98c000,bits: HSYNC OFLOW OCERR*
OCERR @ 1c98c014,bits: HSYNC OFLOW OCERR*
OCERR @ 1c98c014,bits: HSYNC OFLOW OCERR*
OCERR @ 1c98c014,bits: HSYNC OFLOW OCERR*
OCERR @ 1c98c014,bits: HSYNC OFLOW OCERR*
OCERR @ 1c98c000,bits: HSYNC OFLOW OCERR*
timeout: drop=1 irq=5755/7129, risc=1854901c, bits: HSYNC OFLOW
reset, reinitialize
PLL: 28636363 => 35468950 . ok
bttv3: OCERR @ 1c98c01c,bits: VSYNC HSYNC OFLOW RISCI* OCERR*
bttv3: OCERR @ 1c98c000,bits: VSYNC HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c000,bits: VSYNC HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c000,bits: VSYNC HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c014,bits: VSYNC HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c000,bits: VSYNC HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c000,bits: VSYNC HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c000,bits: VSYNC HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c000,bits: VSYNC HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c000,bits: VSYNC HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c000,bits: VSYNC HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c000,bits: VSYNC HSYNC OFLOW OCERR*
bttv3: OCERR @ 1c98c000,bits: VSYNC HSYNC OFLOW OCERR*
bttv3: timeout: drop=1 irq=5828/7216, risc=1c98c01c, bits: VSYNC HSYNC OFLOW
bttv3: reset, reinitialize
bttv3: PLL: 28636363 => 35468950 . ok
Unable to handle kernel paging request at virtual address 14000274
printing eip:
c013cda5
*pde = 00000000
Oops: 0002 [#1]
PREEMPT
Modules linked in: i915 drm ohci_hcd tuner tvaudio bttv video_buf
i2c_algo_bit v4l2_common btcx_risc tveeprom i2c_core videodev ehci_hcd
uhci_hcd snd_pcm_oss snd_mixer_oss snd_seq_oss snd_seq_midi_event
snd_seq snd_seq_device snd_bt87x snd_hda_intel snd_hda_codec snd_pcm
snd_timer snd soundcore snd_page_alloc usbcore
CPU: 0
EIP: 0060:[<c013cda5>] Not tainted VLI
EFLAGS: 00010082 (2.6.15.1)
EIP is at free_block+0x45/0xd1
eax: 14000270 ebx: d8b34000 ecx: 203dc788 edx: 00000000
esi: df6eac00 edi: 00000000 ebp: df67ad00 esp: df64dee4
ds: 007b es: 007b ss: 0068
Process events/0 (pid: 4, threadinfo=df64c000 task=df659a90)
Stack: df4d8a50 00000006 d8b341e4 df67c610 00000007 df67c600 00000000
c013d3e7
df67ad00 df67c610 00000007 00000000 df67ad00 df64c000 df6eab50 df6eac00
df67ad00 c013d47c df67ad00 df67c600 00000000 00000000 00000002 df67ad4c
Call Trace:
[<c013d3e7>] drain_array_locked+0x6a/0x95
[<c013d47c>] cache_reap+0x6a/0x173
[<c0126193>] worker_thread+0x1a3/0x230
[<c013d412>] cache_reap+0x0/0x173
[<c011624d>] default_wake_function+0x0/0x12
[<c011624d>] default_wake_function+0x0/0x12
[<c0125ff0>] worker_thread+0x0/0x230
[<c012968e>] kthread+0x79/0xa3
[<c0129615>] kthread+0x0/0xa3
[<c01012c5>] kernel_thread_helper+0x5/0xb
Code: 24 8b 54 24 2c 8b 04 b8 89 44 24 08 05 00 00 00 40 c1 e8 0c 8b 74
95 14 31 d2 c1 e0 05 03 05 30 e7 3d c0 8b 58 1c 8b 03 8b 4b 04 <89> 48
04 89 01 c7 43 04 00 02 20 00 c7 03 00 01 10 00 8b 43 0c
<6>note: events/0[4] exited with preempt_count 1
Best Regards,
Jiri Tyr
On Wed, Mar 15, 2006 at 04:25:34PM +0100, Jiri Tyr wrote:
> Sami Farin wrote:
>
> >I didn't change xawtv configs, and
> >1) with the patch system did not crash
> >2) without the patch system crashed
> >
> >
I'd appreciate if you didn't delete the Mail-Followup-To header.
Also, I don't need a personal copy. That's exactly why there's no my
email in Mail-Followup-To.
> I've tryed to apply your patch and tested it and I've got the same
It's not my patch.
It was made by Duncan Sands.
> result like without your patch - by manipulation with the XAWTV channel
> list the PC crashed and I've got in the /var/log/message this:
Sorry to hear about your crash.
I suggest that you wait till Duncan or somebody else
releases the "final" patch.
--