Bootdata ok (command line is ro root=LABEL=/)
Linux version 2.6.15-rc1 ([email protected]) (gcc version 3.4.5 20051201 (Red Hat 3.4.5-2)) #1 SMP PREEMPT Fri Aug 18 12:19:57 EDT 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000002fff0000 (usable)
BIOS-e820: 000000002fff0000 - 000000002fff3000 (ACPI NVS)
BIOS-e820: 000000002fff3000 - 0000000030000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
ACPI: RSDP (v000 VIAK8M ) @ 0x00000000000f6d10
ACPI: RSDT (v001 VIAK8M AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000002fff3000
ACPI: FADT (v001 VIAK8M AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000002fff3040
ACPI: MADT (v001 VIAK8M AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000002fff7ec0
ACPI: DSDT (v001 VIAK8M AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x0000000000000000
On node 0 totalpages: 196495
DMA zone: 3999 pages, LIFO batch:2
Normal zone: 192496 pages, LIFO batch:64
HighMem zone: 0 pages, LIFO batch:2
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 30000000:cec00000)
Checking aperture...
CPU 0: aperture @ d8000000 size 128 MB
Built 1 zonelists
Kernel command line: ro root=LABEL=/
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 3.579545 MHz PM timer.
time.c: Detected 1599.893 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 767952k/786368k available (2828k kernel code, 17820k reserved, 937k data, 220k init)
Calibrating delay using timer specific routine.. 3207.40 BogoMIPS (lpj=6414818)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 128K (64 bytes/line)
mtrr: v2.0 (20020519)
Using local APIC timer interrupts.
Detected 12.499 MHz APIC timer.
Brought up 1 CPUs
time.c: Using PIT/TSC based timekeeping.
testing NMI watchdog ... OK.
checking if image is initramfs... it is
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12) *5
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs *20)
ACPI: PCI Interrupt Link [ALKB] (IRQs *21)
ACPI: PCI Interrupt Link [ALKC] (IRQs *22)
ACPI: PCI Interrupt Link [ALKD] (IRQs *23)
Linux Plug and Play Support v0.97 (c) Adam Belay
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 128M @ 0xd8000000
PCI-DMA: Disabling IOMMU.
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: e8000000-e9ffffff
PREFETCH window: e0000000-e7ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1155904651.488:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
usbmon: debugfs is not available
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ACPI: CPU0 (power states: C1[C1])
ACPI: Thermal Zone [THRM] (46 C)
ibm_acpi: ec object not found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKD] -> GSI 23 (level, low) -> IRQ 169
PCI: Via IRQ fixup for 0000:00:12.0, from 10 to 9
eth0: VIA Rhine II at 0xea021000, 00:50:8d:7a:83:09, IRQ 169.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 177
PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xcc00-0xcc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xcc08-0xcc0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: WDC WD400BB-00FJA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: LITE-ON DVDRW SHW-160P6S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3
hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard as /class/input/input0
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Power state transitions not supported
Freeing unused kernel memory: 220k freed
SCSI subsystem initialized
libata version 1.12 loaded.
sata_via 0000:00:0f.0: version 1.1
ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 177
PCI: Via IRQ fixup for 0000:00:0f.0, from 11 to 1
sata_via 0000:00:0f.0: routed to hard irq line 1
ata1: SATA max UDMA/133 cmd 0xB400 ctl 0xB802 bmdma 0xC400 irq 177
ata2: SATA max UDMA/133 cmd 0xBC00 ctl 0xC002 bmdma 0xC408 irq 177
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3468 86:3c01 87:4003 88:407f
ata1: dev 0 ATA-6, max UDMA/133, 390721968 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_via
ata2: no device found (phy stat 00000000)
scsi1 : sata_via
Vendor: ATA Model: ST3200822AS Rev: 3.01
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
SCSI device sda: drive cache: write back
sda: sda1
sd 0:0:0:0: Attached scsi disk sda
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 185
3c59x: Donald Becker and others. http://www.scyld.com/network/vortex.html
0000:00:09.0: 3Com PCI 3c905B Cyclone 100baseTx at ffffc20000010000. Vers LK1.1.19
via82xx: Assuming DXS channels with 48k fixed sample rate.
Please try dxs_support=5 option
and report if it works on your machine.
For more details, read ALSA-Configuration.txt.
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 193
PCI: Via IRQ fixup for 0000:00:11.5, from 5 to 1
PCI: Setting latency timer of device 0000:00:11.5 to 64
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 201
PCI: Via IRQ fixup for 0000:00:10.4, from 5 to 9
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 201, io mem 0xea020000
ehci_hcd 0000:00:10.4: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usb 1-2: new high speed USB device using ehci_hcd and address 2
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 201
PCI: Via IRQ fixup for 0000:00:10.0, from 10 to 9
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 201, io base 0x0000d000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 201
PCI: Via IRQ fixup for 0000:00:10.1, from 10 to 9
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 201, io base 0x0000d400
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 201
PCI: Via IRQ fixup for 0000:00:10.2, from 11 to 9
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 201, io base 0x0000d800
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 201
PCI: Via IRQ fixup for 0000:00:10.3, from 11 to 9
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 201, io base 0x0000dc00
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
EXT3 FS on hda3, internal journal
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [email protected]
cdrom: open failed.
XFS mounting filesystem sda1
Ending clean XFS mount for filesystem: sda1
Adding 1020116k swap on /dev/hda2. Priority:-1 extents:1 across:1020116k
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Vendor: ST330083 Model: 1A Rev: 0 0
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdb: 586072368 512-byte hdwr sectors (300069 MB)
sdb: assuming drive cache: write through
SCSI device sdb: 586072368 512-byte hdwr sectors (300069 MB)
sdb: assuming drive cache: write through
sdb: sdb1
sd 2:0:0:0: Attached scsi disk sdb
usb-storage: device scan complete
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff80465f80(lo)
IPv6 over IPv4 tunneling driver
[drm] Initialized drm 1.0.0 20040925
hald[3026]: segfault at 0000000000000000 rip 00000034a9f6fed0 rsp 00007ffffff781d8 error 4
eth0: no IPv6 routers present