From: Divy Le Ray <[email protected]>
This patch implements the HW access routines for the
Chelsio T3 network adapter's driver.
This patch is split. This is the second part.
Signed-off-by: Divy Le Ray <[email protected]>
---
+/**
+ * t3_port_intr_enable - enable port-specific interrupts
+ * @adapter: associated adapter
+ * @idx: index of port whose interrupts should be enabled
+ *
+ * Enable port-specific (i.e., MAC and PHY) interrupts for the given
+ * adapter port.
+ */
+void t3_port_intr_enable(struct adapter *adapter, int idx)
+{
+ struct cphy *phy = &adap2pinfo(adapter, idx)->phy;
+
+ t3_write_reg(adapter, XGM_REG(A_XGM_INT_ENABLE, idx), XGM_INTR_MASK);
+ phy->ops->intr_enable(phy);
+}
+
+/**
+ * t3_port_intr_disable - disable port-specific interrupts
+ * @adapter: associated adapter
+ * @idx: index of port whose interrupts should be disabled
+ *
+ * Disable port-specific (i.e., MAC and PHY) interrupts for the given
+ * adapter port.
+ */
+void t3_port_intr_disable(struct adapter *adapter, int idx)
+{
+ struct cphy *phy = &adap2pinfo(adapter, idx)->phy;
+
+ t3_write_reg(adapter, XGM_REG(A_XGM_INT_ENABLE, idx), 0);
+ phy->ops->intr_disable(phy);
+}
+
+/**
+ * t3_port_intr_clear - clear port-specific interrupts
+ * @adapter: associated adapter
+ * @idx: index of port whose interrupts to clear
+ *
+ * Clear port-specific (i.e., MAC and PHY) interrupts for the given
+ * adapter port.
+ */
+void t3_port_intr_clear(struct adapter *adapter, int idx)
+{
+ struct cphy *phy = &adap2pinfo(adapter, idx)->phy;
+
+ t3_write_reg(adapter, XGM_REG(A_XGM_INT_CAUSE, idx), 0xffffffff);
+ phy->ops->intr_clear(phy);
+}
+
+/**
+ * t3_sge_write_context - write an SGE context
+ * @adapter: the adapter
+ * @id: the context id
+ * @type: the context type
+ *
+ * Program an SGE context with the values already loaded in the
+ * CONTEXT_DATA? registers.
+ */
+static int t3_sge_write_context(struct adapter *adapter, unsigned int id,
+ unsigned int type)
+{
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK0, 0xffffffff);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK1, 0xffffffff);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK2, 0xffffffff);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK3, 0xffffffff);
+ t3_write_reg(adapter, A_SG_CONTEXT_CMD,
+ V_CONTEXT_CMD_OPCODE(1) | type | V_CONTEXT(id));
+ return t3_wait_op_done(adapter, A_SG_CONTEXT_CMD, F_CONTEXT_CMD_BUSY,
+ 0, 5, 1);
+}
+
+/**
+ * t3_sge_init_ecntxt - initialize an SGE egress context
+ * @adapter: the adapter to configure
+ * @id: the context id
+ * @gts_enable: whether to enable GTS for the context
+ * @type: the egress context type
+ * @respq: associated response queue
+ * @base_addr: base address of queue
+ * @size: number of queue entries
+ * @token: uP token
+ * @gen: initial generation value for the context
+ * @cidx: consumer pointer
+ *
+ * Initialize an SGE egress context and make it ready for use. If the
+ * platform allows concurrent context operations, the caller is
+ * responsible for appropriate locking.
+ */
+int t3_sge_init_ecntxt(struct adapter *adapter, unsigned int id, int gts_enable,
+ enum sge_context_type type, int respq, u64 base_addr,
+ unsigned int size, unsigned int token, int gen,
+ unsigned int cidx)
+{
+ unsigned int credits = type == SGE_CNTXT_OFLD ? 0 : FW_WR_NUM;
+
+ if (base_addr & 0xfff) /* must be 4K aligned */
+ return -EINVAL;
+ if (t3_read_reg(adapter, A_SG_CONTEXT_CMD) & F_CONTEXT_CMD_BUSY)
+ return -EBUSY;
+
+ base_addr >>= 12;
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA0, V_EC_INDEX(cidx) |
+ V_EC_CREDITS(credits) | V_EC_GTS(gts_enable));
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA1, V_EC_SIZE(size) |
+ V_EC_BASE_LO(base_addr & 0xffff));
+ base_addr >>= 16;
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA2, base_addr);
+ base_addr >>= 32;
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA3,
+ V_EC_BASE_HI(base_addr & 0xf) | V_EC_RESPQ(respq) |
+ V_EC_TYPE(type) | V_EC_GEN(gen) | V_EC_UP_TOKEN(token) |
+ F_EC_VALID);
+ return t3_sge_write_context(adapter, id, F_EGRESS);
+}
+
+/**
+ * t3_sge_init_flcntxt - initialize an SGE free-buffer list context
+ * @adapter: the adapter to configure
+ * @id: the context id
+ * @gts_enable: whether to enable GTS for the context
+ * @base_addr: base address of queue
+ * @size: number of queue entries
+ * @bsize: size of each buffer for this queue
+ * @cong_thres: threshold to signal congestion to upstream producers
+ * @gen: initial generation value for the context
+ * @cidx: consumer pointer
+ *
+ * Initialize an SGE free list context and make it ready for use. The
+ * caller is responsible for ensuring only one context operation occurs
+ * at a time.
+ */
+int t3_sge_init_flcntxt(struct adapter *adapter, unsigned int id,
+ int gts_enable, u64 base_addr, unsigned int size,
+ unsigned int bsize, unsigned int cong_thres, int gen,
+ unsigned int cidx)
+{
+ if (base_addr & 0xfff) /* must be 4K aligned */
+ return -EINVAL;
+ if (t3_read_reg(adapter, A_SG_CONTEXT_CMD) & F_CONTEXT_CMD_BUSY)
+ return -EBUSY;
+
+ base_addr >>= 12;
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA0, base_addr);
+ base_addr >>= 32;
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA1,
+ V_FL_BASE_HI((u32) base_addr) |
+ V_FL_INDEX_LO(cidx & M_FL_INDEX_LO));
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA2, V_FL_SIZE(size) |
+ V_FL_GEN(gen) | V_FL_INDEX_HI(cidx >> 12) |
+ V_FL_ENTRY_SIZE_LO(bsize & M_FL_ENTRY_SIZE_LO));
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA3,
+ V_FL_ENTRY_SIZE_HI(bsize >> (32 - S_FL_ENTRY_SIZE_LO)) |
+ V_FL_CONG_THRES(cong_thres) | V_FL_GTS(gts_enable));
+ return t3_sge_write_context(adapter, id, F_FREELIST);
+}
+
+/**
+ * t3_sge_init_rspcntxt - initialize an SGE response queue context
+ * @adapter: the adapter to configure
+ * @id: the context id
+ * @irq_vec_idx: MSI-X interrupt vector index, 0 if no MSI-X, -1 if no IRQ
+ * @base_addr: base address of queue
+ * @size: number of queue entries
+ * @fl_thres: threshold for selecting the normal or jumbo free list
+ * @gen: initial generation value for the context
+ * @cidx: consumer pointer
+ *
+ * Initialize an SGE response queue context and make it ready for use.
+ * The caller is responsible for ensuring only one context operation
+ * occurs at a time.
+ */
+int t3_sge_init_rspcntxt(struct adapter *adapter, unsigned int id,
+ int irq_vec_idx, u64 base_addr, unsigned int size,
+ unsigned int fl_thres, int gen, unsigned int cidx)
+{
+ unsigned int intr = 0;
+
+ if (base_addr & 0xfff) /* must be 4K aligned */
+ return -EINVAL;
+ if (t3_read_reg(adapter, A_SG_CONTEXT_CMD) & F_CONTEXT_CMD_BUSY)
+ return -EBUSY;
+
+ base_addr >>= 12;
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA0, V_CQ_SIZE(size) |
+ V_CQ_INDEX(cidx));
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA1, base_addr);
+ base_addr >>= 32;
+ if (irq_vec_idx >= 0)
+ intr = V_RQ_MSI_VEC(irq_vec_idx) | F_RQ_INTR_EN;
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA2,
+ V_CQ_BASE_HI((u32) base_addr) | intr | V_RQ_GEN(gen));
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA3, fl_thres);
+ return t3_sge_write_context(adapter, id, F_RESPONSEQ);
+}
+
+/**
+ * t3_sge_init_cqcntxt - initialize an SGE completion queue context
+ * @adapter: the adapter to configure
+ * @id: the context id
+ * @base_addr: base address of queue
+ * @size: number of queue entries
+ * @rspq: response queue for async notifications
+ * @ovfl_mode: CQ overflow mode
+ * @credits: completion queue credits
+ * @credit_thres: the credit threshold
+ *
+ * Initialize an SGE completion queue context and make it ready for use.
+ * The caller is responsible for ensuring only one context operation
+ * occurs at a time.
+ */
+int t3_sge_init_cqcntxt(struct adapter *adapter, unsigned int id, u64 base_addr,
+ unsigned int size, int rspq, int ovfl_mode,
+ unsigned int credits, unsigned int credit_thres)
+{
+ if (base_addr & 0xfff) /* must be 4K aligned */
+ return -EINVAL;
+ if (t3_read_reg(adapter, A_SG_CONTEXT_CMD) & F_CONTEXT_CMD_BUSY)
+ return -EBUSY;
+
+ base_addr >>= 12;
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA0, V_CQ_SIZE(size));
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA1, base_addr);
+ base_addr >>= 32;
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA2,
+ V_CQ_BASE_HI((u32) base_addr) | V_CQ_RSPQ(rspq) |
+ V_CQ_GEN(1) | V_CQ_OVERFLOW_MODE(ovfl_mode));
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA3, V_CQ_CREDITS(credits) |
+ V_CQ_CREDIT_THRES(credit_thres));
+ return t3_sge_write_context(adapter, id, F_CQ);
+}
+
+/**
+ * t3_sge_enable_ecntxt - enable/disable an SGE egress context
+ * @adapter: the adapter
+ * @id: the egress context id
+ * @enable: enable (1) or disable (0) the context
+ *
+ * Enable or disable an SGE egress context. The caller is responsible for
+ * ensuring only one context operation occurs at a time.
+ */
+int t3_sge_enable_ecntxt(struct adapter *adapter, unsigned int id, int enable)
+{
+ if (t3_read_reg(adapter, A_SG_CONTEXT_CMD) & F_CONTEXT_CMD_BUSY)
+ return -EBUSY;
+
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK0, 0);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK1, 0);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK2, 0);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK3, F_EC_VALID);
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA3, V_EC_VALID(enable));
+ t3_write_reg(adapter, A_SG_CONTEXT_CMD,
+ V_CONTEXT_CMD_OPCODE(1) | F_EGRESS | V_CONTEXT(id));
+ return t3_wait_op_done(adapter, A_SG_CONTEXT_CMD, F_CONTEXT_CMD_BUSY,
+ 0, 5, 1);
+}
+
+/**
+ * t3_sge_disable_fl - disable an SGE free-buffer list
+ * @adapter: the adapter
+ * @id: the free list context id
+ *
+ * Disable an SGE free-buffer list. The caller is responsible for
+ * ensuring only one context operation occurs at a time.
+ */
+int t3_sge_disable_fl(struct adapter *adapter, unsigned int id)
+{
+ if (t3_read_reg(adapter, A_SG_CONTEXT_CMD) & F_CONTEXT_CMD_BUSY)
+ return -EBUSY;
+
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK0, 0);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK1, 0);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK2, V_FL_SIZE(M_FL_SIZE));
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK3, 0);
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA2, 0);
+ t3_write_reg(adapter, A_SG_CONTEXT_CMD,
+ V_CONTEXT_CMD_OPCODE(1) | F_FREELIST | V_CONTEXT(id));
+ return t3_wait_op_done(adapter, A_SG_CONTEXT_CMD, F_CONTEXT_CMD_BUSY,
+ 0, 5, 1);
+}
+
+/**
+ * t3_sge_disable_rspcntxt - disable an SGE response queue
+ * @adapter: the adapter
+ * @id: the response queue context id
+ *
+ * Disable an SGE response queue. The caller is responsible for
+ * ensuring only one context operation occurs at a time.
+ */
+int t3_sge_disable_rspcntxt(struct adapter *adapter, unsigned int id)
+{
+ if (t3_read_reg(adapter, A_SG_CONTEXT_CMD) & F_CONTEXT_CMD_BUSY)
+ return -EBUSY;
+
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK0, V_CQ_SIZE(M_CQ_SIZE));
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK1, 0);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK2, 0);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK3, 0);
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA0, 0);
+ t3_write_reg(adapter, A_SG_CONTEXT_CMD,
+ V_CONTEXT_CMD_OPCODE(1) | F_RESPONSEQ | V_CONTEXT(id));
+ return t3_wait_op_done(adapter, A_SG_CONTEXT_CMD, F_CONTEXT_CMD_BUSY,
+ 0, 5, 1);
+}
+
+/**
+ * t3_sge_disable_cqcntxt - disable an SGE completion queue
+ * @adapter: the adapter
+ * @id: the completion queue context id
+ *
+ * Disable an SGE completion queue. The caller is responsible for
+ * ensuring only one context operation occurs at a time.
+ */
+int t3_sge_disable_cqcntxt(struct adapter *adapter, unsigned int id)
+{
+ if (t3_read_reg(adapter, A_SG_CONTEXT_CMD) & F_CONTEXT_CMD_BUSY)
+ return -EBUSY;
+
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK0, V_CQ_SIZE(M_CQ_SIZE));
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK1, 0);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK2, 0);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK3, 0);
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA0, 0);
+ t3_write_reg(adapter, A_SG_CONTEXT_CMD,
+ V_CONTEXT_CMD_OPCODE(1) | F_CQ | V_CONTEXT(id));
+ return t3_wait_op_done(adapter, A_SG_CONTEXT_CMD, F_CONTEXT_CMD_BUSY,
+ 0, 5, 1);
+}
+
+/**
+ * t3_sge_cqcntxt_op - perform an operation on a completion queue context
+ * @adapter: the adapter
+ * @id: the context id
+ * @op: the operation to perform
+ *
+ * Perform the selected operation on an SGE completion queue context.
+ * The caller is responsible for ensuring only one context operation
+ * occurs at a time.
+ */
+int t3_sge_cqcntxt_op(struct adapter *adapter, unsigned int id, unsigned int op,
+ unsigned int credits)
+{
+ u32 val;
+
+ if (t3_read_reg(adapter, A_SG_CONTEXT_CMD) & F_CONTEXT_CMD_BUSY)
+ return -EBUSY;
+
+ t3_write_reg(adapter, A_SG_CONTEXT_DATA0, credits << 16);
+ t3_write_reg(adapter, A_SG_CONTEXT_CMD, V_CONTEXT_CMD_OPCODE(op) |
+ V_CONTEXT(id) | F_CQ);
+ if (t3_wait_op_done_val(adapter, A_SG_CONTEXT_CMD, F_CONTEXT_CMD_BUSY,
+ 0, 5, 1, &val))
+ return -EIO;
+
+ if (op >= 2 && op < 7) {
+ if (adapter->params.rev > 0)
+ return G_CQ_INDEX(val);
+
+ t3_write_reg(adapter, A_SG_CONTEXT_CMD,
+ V_CONTEXT_CMD_OPCODE(0) | F_CQ | V_CONTEXT(id));
+ if (t3_wait_op_done(adapter, A_SG_CONTEXT_CMD,
+ F_CONTEXT_CMD_BUSY, 0, 5, 1))
+ return -EIO;
+ return G_CQ_INDEX(t3_read_reg(adapter, A_SG_CONTEXT_DATA0));
+ }
+ return 0;
+}
+
+/**
+ * t3_sge_read_context - read an SGE context
+ * @type: the context type
+ * @adapter: the adapter
+ * @id: the context id
+ * @data: holds the retrieved context
+ *
+ * Read an SGE egress context. The caller is responsible for ensuring
+ * only one context operation occurs at a time.
+ */
+static int t3_sge_read_context(unsigned int type, struct adapter *adapter,
+ unsigned int id, u32 data[4])
+{
+ if (t3_read_reg(adapter, A_SG_CONTEXT_CMD) & F_CONTEXT_CMD_BUSY)
+ return -EBUSY;
+
+ t3_write_reg(adapter, A_SG_CONTEXT_CMD,
+ V_CONTEXT_CMD_OPCODE(0) | type | V_CONTEXT(id));
+ if (t3_wait_op_done(adapter, A_SG_CONTEXT_CMD, F_CONTEXT_CMD_BUSY, 0,
+ 5, 1))
+ return -EIO;
+ data[0] = t3_read_reg(adapter, A_SG_CONTEXT_DATA0);
+ data[1] = t3_read_reg(adapter, A_SG_CONTEXT_DATA1);
+ data[2] = t3_read_reg(adapter, A_SG_CONTEXT_DATA2);
+ data[3] = t3_read_reg(adapter, A_SG_CONTEXT_DATA3);
+ return 0;
+}
+
+/**
+ * t3_sge_read_ecntxt - read an SGE egress context
+ * @adapter: the adapter
+ * @id: the context id
+ * @data: holds the retrieved context
+ *
+ * Read an SGE egress context. The caller is responsible for ensuring
+ * only one context operation occurs at a time.
+ */
+int t3_sge_read_ecntxt(struct adapter *adapter, unsigned int id, u32 data[4])
+{
+ if (id >= 65536)
+ return -EINVAL;
+ return t3_sge_read_context(F_EGRESS, adapter, id, data);
+}
+
+/**
+ * t3_sge_read_cq - read an SGE CQ context
+ * @adapter: the adapter
+ * @id: the context id
+ * @data: holds the retrieved context
+ *
+ * Read an SGE CQ context. The caller is responsible for ensuring
+ * only one context operation occurs at a time.
+ */
+int t3_sge_read_cq(struct adapter *adapter, unsigned int id, u32 data[4])
+{
+ if (id >= 65536)
+ return -EINVAL;
+ return t3_sge_read_context(F_CQ, adapter, id, data);
+}
+
+/**
+ * t3_sge_read_fl - read an SGE free-list context
+ * @adapter: the adapter
+ * @id: the context id
+ * @data: holds the retrieved context
+ *
+ * Read an SGE free-list context. The caller is responsible for ensuring
+ * only one context operation occurs at a time.
+ */
+int t3_sge_read_fl(struct adapter *adapter, unsigned int id, u32 data[4])
+{
+ if (id >= SGE_QSETS * 2)
+ return -EINVAL;
+ return t3_sge_read_context(F_FREELIST, adapter, id, data);
+}
+
+/**
+ * t3_sge_read_rspq - read an SGE response queue context
+ * @adapter: the adapter
+ * @id: the context id
+ * @data: holds the retrieved context
+ *
+ * Read an SGE response queue context. The caller is responsible for
+ * ensuring only one context operation occurs at a time.
+ */
+int t3_sge_read_rspq(struct adapter *adapter, unsigned int id, u32 data[4])
+{
+ if (id >= SGE_QSETS)
+ return -EINVAL;
+ return t3_sge_read_context(F_RESPONSEQ, adapter, id, data);
+}
+
+/**
+ * t3_config_rss - configure Rx packet steering
+ * @adapter: the adapter
+ * @rss_config: RSS settings (written to TP_RSS_CONFIG)
+ * @cpus: values for the CPU lookup table (0xff terminated)
+ * @rspq: values for the response queue lookup table (0xffff terminated)
+ *
+ * Programs the receive packet steering logic. @cpus and @rspq provide
+ * the values for the CPU and response queue lookup tables. If they
+ * provide fewer values than the size of the tables the supplied values
+ * are used repeatedly until the tables are fully populated.
+ */
+void t3_config_rss(struct adapter *adapter, unsigned int rss_config,
+ const u8 * cpus, const u16 *rspq)
+{
+ int i, j, cpu_idx = 0, q_idx = 0;
+
+ if (cpus)
+ for (i = 0; i < RSS_TABLE_SIZE; ++i) {
+ u32 val = i << 16;
+
+ for (j = 0; j < 2; ++j) {
+ val |= (cpus[cpu_idx++] & 0x3f) << (8 * j);
+ if (cpus[cpu_idx] == 0xff)
+ cpu_idx = 0;
+ }
+ t3_write_reg(adapter, A_TP_RSS_LKP_TABLE, val);
+ }
+
+ if (rspq)
+ for (i = 0; i < RSS_TABLE_SIZE; ++i) {
+ t3_write_reg(adapter, A_TP_RSS_MAP_TABLE,
+ (i << 16) | rspq[q_idx++]);
+ if (rspq[q_idx] == 0xffff)
+ q_idx = 0;
+ }
+
+ t3_write_reg(adapter, A_TP_RSS_CONFIG, rss_config);
+}
+
+/**
+ * t3_read_rss - read the contents of the RSS tables
+ * @adapter: the adapter
+ * @lkup: holds the contents of the RSS lookup table
+ * @map: holds the contents of the RSS map table
+ *
+ * Reads the contents of the receive packet steering tables.
+ */
+int t3_read_rss(struct adapter *adapter, u8 * lkup, u16 *map)
+{
+ int i;
+ u32 val;
+
+ if (lkup)
+ for (i = 0; i < RSS_TABLE_SIZE; ++i) {
+ t3_write_reg(adapter, A_TP_RSS_LKP_TABLE,
+ 0xffff0000 | i);
+ val = t3_read_reg(adapter, A_TP_RSS_LKP_TABLE);
+ if (!(val & 0x80000000))
+ return -EAGAIN;
+ *lkup++ = val;
+ *lkup++ = (val >> 8);
+ }
+
+ if (map)
+ for (i = 0; i < RSS_TABLE_SIZE; ++i) {
+ t3_write_reg(adapter, A_TP_RSS_MAP_TABLE,
+ 0xffff0000 | i);
+ val = t3_read_reg(adapter, A_TP_RSS_MAP_TABLE);
+ if (!(val & 0x80000000))
+ return -EAGAIN;
+ *map++ = val;
+ }
+ return 0;
+}
+
+/**
+ * t3_tp_set_offload_mode - put TP in NIC/offload mode
+ * @adap: the adapter
+ * @enable: 1 to select offload mode, 0 for regular NIC
+ *
+ * Switches TP to NIC/offload mode.
+ */
+void t3_tp_set_offload_mode(struct adapter *adap, int enable)
+{
+ if (is_offload(adap) || !enable)
+ t3_set_reg_field(adap, A_TP_IN_CONFIG, F_NICMODE,
+ V_NICMODE(!enable));
+}
+
+/**
+ * pm_num_pages - calculate the number of pages of the payload memory
+ * @mem_size: the size of the payload memory
+ * @pg_size: the size of each payload memory page
+ *
+ * Calculate the number of pages, each of the given size, that fit in a
+ * memory of the specified size, respecting the HW requirement that the
+ * number of pages must be a multiple of 24.
+ */
+static inline unsigned int pm_num_pages(unsigned int mem_size,
+ unsigned int pg_size)
+{
+ unsigned int n = mem_size / pg_size;
+
+ return n - n % 24;
+}
+
+#define mem_region(adap, start, size, reg) \
+ t3_write_reg((adap), A_ ## reg, (start)); \
+ start += size
+
+/*
+ * partition_mem - partition memory and configure TP memory settings
+ * @adap: the adapter
+ * @p: the TP parameters
+ *
+ * Partitions context and payload memory and configures TP's memory
+ * registers.
+ */
+static void partition_mem(struct adapter *adap, const struct tp_params *p)
+{
+ unsigned int m, pstructs, tids = t3_mc5_size(&adap->mc5);
+ unsigned int timers = 0, timers_shift = 22;
+
+ if (adap->params.rev > 0) {
+ if (tids <= 16 * 1024) {
+ timers = 1;
+ timers_shift = 16;
+ } else if (tids <= 64 * 1024) {
+ timers = 2;
+ timers_shift = 18;
+ } else if (tids <= 256 * 1024) {
+ timers = 3;
+ timers_shift = 20;
+ }
+ }
+
+ t3_write_reg(adap, A_TP_PMM_SIZE,
+ p->chan_rx_size | (p->chan_tx_size >> 16));
+
+ t3_write_reg(adap, A_TP_PMM_TX_BASE, 0);
+ t3_write_reg(adap, A_TP_PMM_TX_PAGE_SIZE, p->tx_pg_size);
+ t3_write_reg(adap, A_TP_PMM_TX_MAX_PAGE, p->tx_num_pgs);
+ t3_set_reg_field(adap, A_TP_PARA_REG3, V_TXDATAACKIDX(M_TXDATAACKIDX),
+ V_TXDATAACKIDX(fls(p->tx_pg_size) - 12));
+
+ t3_write_reg(adap, A_TP_PMM_RX_BASE, 0);
+ t3_write_reg(adap, A_TP_PMM_RX_PAGE_SIZE, p->rx_pg_size);
+ t3_write_reg(adap, A_TP_PMM_RX_MAX_PAGE, p->rx_num_pgs);
+
+ pstructs = p->rx_num_pgs + p->tx_num_pgs;
+ /* Add a bit of headroom and make multiple of 24 */
+ pstructs += 48;
+ pstructs -= pstructs % 24;
+ t3_write_reg(adap, A_TP_CMM_MM_MAX_PSTRUCT, pstructs);
+
+ m = tids * TCB_SIZE;
+ mem_region(adap, m, (64 << 10) * 64, SG_EGR_CNTX_BADDR);
+ mem_region(adap, m, (64 << 10) * 64, SG_CQ_CONTEXT_BADDR);
+ t3_write_reg(adap, A_TP_CMM_TIMER_BASE, V_CMTIMERMAXNUM(timers) | m);
+ m += ((p->ntimer_qs - 1) << timers_shift) + (1 << 22);
+ mem_region(adap, m, pstructs * 64, TP_CMM_MM_BASE);
+ mem_region(adap, m, 64 * (pstructs / 24), TP_CMM_MM_PS_FLST_BASE);
+ mem_region(adap, m, 64 * (p->rx_num_pgs / 24), TP_CMM_MM_RX_FLST_BASE);
+ mem_region(adap, m, 64 * (p->tx_num_pgs / 24), TP_CMM_MM_TX_FLST_BASE);
+
+ m = (m + 4095) & ~0xfff;
+ t3_write_reg(adap, A_CIM_SDRAM_BASE_ADDR, m);
+ t3_write_reg(adap, A_CIM_SDRAM_ADDR_SIZE, p->cm_size - m);
+
+ tids = (p->cm_size - m - (3 << 20)) / 3072 - 32;
+ m = t3_mc5_size(&adap->mc5) - adap->params.mc5.nservers -
+ adap->params.mc5.nfilters - adap->params.mc5.nroutes;
+ if (tids < m)
+ adap->params.mc5.nservers += m - tids;
+}
+
+static inline void tp_wr_indirect(struct adapter *adap, unsigned int addr,
+ u32 val)
+{
+ t3_write_reg(adap, A_TP_PIO_ADDR, addr);
+ t3_write_reg(adap, A_TP_PIO_DATA, val);
+}
+
+static void tp_config(struct adapter *adap, const struct tp_params *p)
+{
+ unsigned int v;
+
+ t3_write_reg(adap, A_TP_GLOBAL_CONFIG, F_TXPACINGENABLE | F_PATHMTU |
+ F_IPCHECKSUMOFFLOAD | F_UDPCHECKSUMOFFLOAD |
+ F_TCPCHECKSUMOFFLOAD | V_IPTTL(64));
+ t3_write_reg(adap, A_TP_TCP_OPTIONS, V_MTUDEFAULT(576) |
+ F_MTUENABLE | V_WINDOWSCALEMODE(1) |
+ V_TIMESTAMPSMODE(1) | V_SACKMODE(1) | V_SACKRX(1));
+ t3_write_reg(adap, A_TP_DACK_CONFIG, V_AUTOSTATE3(1) |
+ V_AUTOSTATE2(1) | V_AUTOSTATE1(0) |
+ V_BYTETHRESHOLD(16384) | V_MSSTHRESHOLD(2) |
+ F_AUTOCAREFUL | F_AUTOENABLE | V_DACK_MODE(1));
+ t3_set_reg_field(adap, A_TP_IN_CONFIG, F_IPV6ENABLE | F_NICMODE,
+ F_IPV6ENABLE | F_NICMODE);
+ t3_write_reg(adap, A_TP_TX_RESOURCE_LIMIT, 0x18141814);
+ t3_write_reg(adap, A_TP_PARA_REG4, 0x5050105);
+ t3_set_reg_field(adap, A_TP_PARA_REG6,
+ adap->params.rev > 0 ? F_ENABLEESND : F_T3A_ENABLEESND,
+ 0);
+
+ v = t3_read_reg(adap, A_TP_PC_CONFIG);
+ v &= ~(F_ENABLEEPCMDAFULL | F_ENABLEOCSPIFULL);
+ t3_write_reg(adap, A_TP_PC_CONFIG, v | F_TXDEFERENABLE |
+ F_MODULATEUNIONMODE | F_HEARBEATDACK |
+ F_TXCONGESTIONMODE | F_RXCONGESTIONMODE);
+
+ v = t3_read_reg(adap, A_TP_PC_CONFIG2);
+ v &= ~F_CHDRAFULL;
+ t3_write_reg(adap, A_TP_PC_CONFIG2, v);
+
+ if (adap->params.rev > 0) {
+ tp_wr_indirect(adap, A_TP_EGRESS_CONFIG, F_REWRITEFORCETOSIZE);
+ t3_set_reg_field(adap, A_TP_PARA_REG3, F_TXPACEAUTO,
+ F_TXPACEAUTO);
+ t3_set_reg_field(adap, A_TP_PC_CONFIG, F_LOCKTID, F_LOCKTID);
+ t3_set_reg_field(adap, A_TP_PARA_REG3, 0, F_TXPACEAUTOSTRICT);
+ } else
+ t3_set_reg_field(adap, A_TP_PARA_REG3, 0, F_TXPACEFIXED);
+
+ t3_write_reg(adap, A_TP_TX_MOD_QUEUE_WEIGHT1, 0x12121212);
+ t3_write_reg(adap, A_TP_TX_MOD_QUEUE_WEIGHT0, 0x12121212);
+ t3_write_reg(adap, A_TP_MOD_CHANNEL_WEIGHT, 0x1212);
+}
+
+/* Desired TP timer resolution in usec */
+#define TP_TMR_RES 50
+
+/* TCP timer values in ms */
+#define TP_DACK_TIMER 50
+#define TP_RTO_MIN 250
+
+/**
+ * tp_set_timers - set TP timing parameters
+ * @adap: the adapter to set
+ * @core_clk: the core clock frequency in Hz
+ *
+ * Set TP's timing parameters, such as the various timer resolutions and
+ * the TCP timer values.
+ */
+static void tp_set_timers(struct adapter *adap, unsigned int core_clk)
+{
+ unsigned int tre = fls(core_clk / (1000000 / TP_TMR_RES)) - 1;
+ unsigned int dack_re = fls(core_clk / 5000) - 1; /* 200us */
+ unsigned int tstamp_re = fls(core_clk / 1000); /* 1ms, at least */
+ unsigned int tps = core_clk >> tre;
+
+ t3_write_reg(adap, A_TP_TIMER_RESOLUTION, V_TIMERRESOLUTION(tre) |
+ V_DELAYEDACKRESOLUTION(dack_re) |
+ V_TIMESTAMPRESOLUTION(tstamp_re));
+ t3_write_reg(adap, A_TP_DACK_TIMER,
+ (core_clk >> dack_re) / (1000 / TP_DACK_TIMER));
+ t3_write_reg(adap, A_TP_TCP_BACKOFF_REG0, 0x3020100);
+ t3_write_reg(adap, A_TP_TCP_BACKOFF_REG1, 0x7060504);
+ t3_write_reg(adap, A_TP_TCP_BACKOFF_REG2, 0xb0a0908);
+ t3_write_reg(adap, A_TP_TCP_BACKOFF_REG3, 0xf0e0d0c);
+ t3_write_reg(adap, A_TP_SHIFT_CNT, V_SYNSHIFTMAX(6) |
+ V_RXTSHIFTMAXR1(4) | V_RXTSHIFTMAXR2(15) |
+ V_PERSHIFTBACKOFFMAX(8) | V_PERSHIFTMAX(8) |
+ V_KEEPALIVEMAX(9));
+
+#define SECONDS * tps
+
+ t3_write_reg(adap, A_TP_MSL, adap->params.rev > 0 ? 0 : 2 SECONDS);
+ t3_write_reg(adap, A_TP_RXT_MIN, tps / (1000 / TP_RTO_MIN));
+ t3_write_reg(adap, A_TP_RXT_MAX, 64 SECONDS);
+ t3_write_reg(adap, A_TP_PERS_MIN, 5 SECONDS);
+ t3_write_reg(adap, A_TP_PERS_MAX, 64 SECONDS);
+ t3_write_reg(adap, A_TP_KEEP_IDLE, 7200 SECONDS);
+ t3_write_reg(adap, A_TP_KEEP_INTVL, 75 SECONDS);
+ t3_write_reg(adap, A_TP_INIT_SRTT, 3 SECONDS);
+ t3_write_reg(adap, A_TP_FINWAIT2_TIMER, 600 SECONDS);
+
+#undef SECONDS
+}
+
+/**
+ * t3_tp_set_coalescing_size - set receive coalescing size
+ * @adap: the adapter
+ * @size: the receive coalescing size
+ * @psh: whether a set PSH bit should deliver coalesced data
+ *
+ * Set the receive coalescing size and PSH bit handling.
+ */
+int t3_tp_set_coalescing_size(struct adapter *adap, unsigned int size, int psh)
+{
+ u32 val;
+
+ if (size > MAX_RX_COALESCING_LEN)
+ return -EINVAL;
+
+ val = t3_read_reg(adap, A_TP_PARA_REG3);
+ val &= ~(F_RXCOALESCEENABLE | F_RXCOALESCEPSHEN);
+
+ if (size) {
+ val |= F_RXCOALESCEENABLE;
+ if (psh)
+ val |= F_RXCOALESCEPSHEN;
+ t3_write_reg(adap, A_TP_PARA_REG2, V_RXCOALESCESIZE(size) |
+ V_MAXRXDATA(MAX_RX_COALESCING_LEN));
+ }
+ t3_write_reg(adap, A_TP_PARA_REG3, val);
+ return 0;
+}
+
+/**
+ * t3_tp_set_max_rxsize - set the max receive size
+ * @adap: the adapter
+ * @size: the max receive size
+ *
+ * Set TP's max receive size. This is the limit that applies when
+ * receive coalescing is disabled.
+ */
+void t3_tp_set_max_rxsize(struct adapter *adap, unsigned int size)
+{
+ t3_write_reg(adap, A_TP_PARA_REG7,
+ V_PMMAXXFERLEN0(size) | V_PMMAXXFERLEN1(size));
+}
+
+static void __devinit init_mtus(unsigned short mtus[])
+{
+ /*
+ * See draft-mathis-plpmtud-00.txt for the values. The min is 88 so
+ * it can accomodate max size TCP/IP headers when SACK and timestamps
+ * are enabled and still have at least 8 bytes of payload.
+ */
+ mtus[0] = 88;
+ mtus[1] = 256;
+ mtus[2] = 512;
+ mtus[3] = 576;
+ mtus[4] = 808;
+ mtus[5] = 1024;
+ mtus[6] = 1280;
+ mtus[7] = 1492;
+ mtus[8] = 1500;
+ mtus[9] = 2002;
+ mtus[10] = 2048;
+ mtus[11] = 4096;
+ mtus[12] = 4352;
+ mtus[13] = 8192;
+ mtus[14] = 9000;
+ mtus[15] = 9600;
+}
+
+/*
+ * Initial congestion control parameters.
+ */
+static void __devinit init_cong_ctrl(unsigned short *a, unsigned short *b)
+{
+ a[0] = a[1] = a[2] = a[3] = a[4] = a[5] = a[6] = a[7] = a[8] = 1;
+ a[9] = 2;
+ a[10] = 3;
+ a[11] = 4;
+ a[12] = 5;
+ a[13] = 6;
+ a[14] = 7;
+ a[15] = 8;
+ a[16] = 9;
+ a[17] = 10;
+ a[18] = 14;
+ a[19] = 17;
+ a[20] = 21;
+ a[21] = 25;
+ a[22] = 30;
+ a[23] = 35;
+ a[24] = 45;
+ a[25] = 60;
+ a[26] = 80;
+ a[27] = 100;
+ a[28] = 200;
+ a[29] = 300;
+ a[30] = 400;
+ a[31] = 500;
+
+ b[0] = b[1] = b[2] = b[3] = b[4] = b[5] = b[6] = b[7] = b[8] = 0;
+ b[9] = b[10] = 1;
+ b[11] = b[12] = 2;
+ b[13] = b[14] = b[15] = b[16] = 3;
+ b[17] = b[18] = b[19] = b[20] = b[21] = 4;
+ b[22] = b[23] = b[24] = b[25] = b[26] = b[27] = 5;
+ b[28] = b[29] = 6;
+ b[30] = b[31] = 7;
+}
+
+/* The minimum additive increment value for the congestion control table */
+#define CC_MIN_INCR 2U
+
+/**
+ * t3_load_mtus - write the MTU and congestion control HW tables
+ * @adap: the adapter
+ * @mtus: the unrestricted values for the MTU table
+ * @alphs: the values for the congestion control alpha parameter
+ * @beta: the values for the congestion control beta parameter
+ * @mtu_cap: the maximum permitted effective MTU
+ *
+ * Write the MTU table with the supplied MTUs capping each at &mtu_cap.
+ * Update the high-speed congestion control table with the supplied alpha,
+ * beta, and MTUs.
+ */
+void t3_load_mtus(struct adapter *adap, unsigned short mtus[NMTUS],
+ unsigned short alpha[NCCTRL_WIN],
+ unsigned short beta[NCCTRL_WIN], unsigned short mtu_cap)
+{
+ static const unsigned int avg_pkts[NCCTRL_WIN] = {
+ 2, 6, 10, 14, 20, 28, 40, 56, 80, 112, 160, 224, 320, 448, 640,
+ 896, 1281, 1792, 2560, 3584, 5120, 7168, 10240, 14336, 20480,
+ 28672, 40960, 57344, 81920, 114688, 163840, 229376
+ };
+
+ unsigned int i, w;
+
+ for (i = 0; i < NMTUS; ++i) {
+ unsigned int mtu = min(mtus[i], mtu_cap);
+ unsigned int log2 = fls(mtu);
+
+ if (!(mtu & ((1 << log2) >> 2))) /* round */
+ log2--;
+ t3_write_reg(adap, A_TP_MTU_TABLE,
+ (i << 24) | (log2 << 16) | mtu);
+
+ for (w = 0; w < NCCTRL_WIN; ++w) {
+ unsigned int inc;
+
+ inc = max(((mtu - 40) * alpha[w]) / avg_pkts[w],
+ CC_MIN_INCR);
+
+ t3_write_reg(adap, A_TP_CCTRL_TABLE, (i << 21) |
+ (w << 16) | (beta[w] << 13) | inc);
+ }
+ }
+}
+
+/**
+ * t3_read_hw_mtus - returns the values in the HW MTU table
+ * @adap: the adapter
+ * @mtus: where to store the HW MTU values
+ *
+ * Reads the HW MTU table.
+ */
+void t3_read_hw_mtus(struct adapter *adap, unsigned short mtus[NMTUS])
+{
+ int i;
+
+ for (i = 0; i < NMTUS; ++i) {
+ unsigned int val;
+
+ t3_write_reg(adap, A_TP_MTU_TABLE, 0xff000000 | i);
+ val = t3_read_reg(adap, A_TP_MTU_TABLE);
+ mtus[i] = val & 0x3fff;
+ }
+}
+
+/**
+ * t3_get_cong_cntl_tab - reads the congestion control table
+ * @adap: the adapter
+ * @incr: where to store the alpha values
+ *
+ * Reads the additive increments programmed into the HW congestion
+ * control table.
+ */
+void t3_get_cong_cntl_tab(struct adapter *adap,
+ unsigned short incr[NMTUS][NCCTRL_WIN])
+{
+ unsigned int mtu, w;
+
+ for (mtu = 0; mtu < NMTUS; ++mtu)
+ for (w = 0; w < NCCTRL_WIN; ++w) {
+ t3_write_reg(adap, A_TP_CCTRL_TABLE,
+ 0xffff0000 | (mtu << 5) | w);
+ incr[mtu][w] = t3_read_reg(adap, A_TP_CCTRL_TABLE) &
+ 0x1fff;
+ }
+}
+
+/**
+ * t3_tp_get_mib_stats - read TP's MIB counters
+ * @adap: the adapter
+ * @tps: holds the returned counter values
+ *
+ * Returns the values of TP's MIB counters.
+ */
+void t3_tp_get_mib_stats(struct adapter *adap, struct tp_mib_stats *tps)
+{
+ t3_read_indirect(adap, A_TP_MIB_INDEX, A_TP_MIB_RDATA, (u32 *) tps,
+ sizeof(*tps) / sizeof(u32), 0);
+}
+
+#define ulp_region(adap, name, start, len) \
+ t3_write_reg((adap), A_ULPRX_ ## name ## _LLIMIT, (start)); \
+ t3_write_reg((adap), A_ULPRX_ ## name ## _ULIMIT, \
+ (start) + (len) - 1); \
+ start += len
+
+#define ulptx_region(adap, name, start, len) \
+ t3_write_reg((adap), A_ULPTX_ ## name ## _LLIMIT, (start)); \
+ t3_write_reg((adap), A_ULPTX_ ## name ## _ULIMIT, \
+ (start) + (len) - 1)
+
+static void ulp_config(struct adapter *adap, const struct tp_params *p)
+{
+ unsigned int m = p->chan_rx_size;
+
+ ulp_region(adap, ISCSI, m, p->chan_rx_size / 8);
+ ulp_region(adap, TDDP, m, p->chan_rx_size / 8);
+ ulptx_region(adap, TPT, m, p->chan_rx_size / 4);
+ ulp_region(adap, STAG, m, p->chan_rx_size / 4);
+ ulp_region(adap, RQ, m, p->chan_rx_size / 4);
+ ulptx_region(adap, PBL, m, p->chan_rx_size / 4);
+ ulp_region(adap, PBL, m, p->chan_rx_size / 4);
+ t3_write_reg(adap, A_ULPRX_TDDP_TAGMASK, 0xffffffff);
+}
+
+void t3_config_trace_filter(struct adapter *adapter,
+ const struct trace_params *tp, int filter_index,
+ int invert, int enable)
+{
+ u32 addr, key[4], mask[4];
+
+ key[0] = tp->sport | (tp->sip << 16);
+ key[1] = (tp->sip >> 16) | (tp->dport << 16);
+ key[2] = tp->dip;
+ key[3] = tp->proto | (tp->vlan << 8) | (tp->intf << 20);
+
+ mask[0] = tp->sport_mask | (tp->sip_mask << 16);
+ mask[1] = (tp->sip_mask >> 16) | (tp->dport_mask << 16);
+ mask[2] = tp->dip_mask;
+ mask[3] = tp->proto_mask | (tp->vlan_mask << 8) | (tp->intf_mask << 20);
+
+ if (invert)
+ key[3] |= (1 << 29);
+ if (enable)
+ key[3] |= (1 << 28);
+
+ addr = filter_index ? A_TP_RX_TRC_KEY0 : A_TP_TX_TRC_KEY0;
+ tp_wr_indirect(adapter, addr++, key[0]);
+ tp_wr_indirect(adapter, addr++, mask[0]);
+ tp_wr_indirect(adapter, addr++, key[1]);
+ tp_wr_indirect(adapter, addr++, mask[1]);
+ tp_wr_indirect(adapter, addr++, key[2]);
+ tp_wr_indirect(adapter, addr++, mask[2]);
+ tp_wr_indirect(adapter, addr++, key[3]);
+ tp_wr_indirect(adapter, addr, mask[3]);
+ t3_read_reg(adapter, A_TP_PIO_DATA);
+}
+
+/**
+ * t3_config_sched - configure a HW traffic scheduler
+ * @adap: the adapter
+ * @kbps: target rate in Kbps
+ * @sched: the scheduler index
+ *
+ * Configure a HW scheduler for the target rate
+ */
+int t3_config_sched(struct adapter *adap, unsigned int kbps, int sched)
+{
+ unsigned int v, tps, cpt, bpt, delta, mindelta = ~0;
+ unsigned int clk = adap->params.vpd.cclk * 1000;
+ unsigned int selected_cpt = 0, selected_bpt = 0;
+
+ if (kbps > 0) {
+ kbps *= 125; /* -> bytes */
+ for (cpt = 1; cpt <= 255; cpt++) {
+ tps = clk / cpt;
+ bpt = (kbps + tps / 2) / tps;
+ if (bpt > 0 && bpt <= 255) {
+ v = bpt * tps;
+ delta = v >= kbps ? v - kbps : kbps - v;
+ if (delta <= mindelta) {
+ mindelta = delta;
+ selected_cpt = cpt;
+ selected_bpt = bpt;
+ }
+ } else if (selected_cpt)
+ break;
+ }
+ if (!selected_cpt)
+ return -EINVAL;
+ }
+ t3_write_reg(adap, A_TP_TM_PIO_ADDR,
+ A_TP_TX_MOD_Q1_Q0_RATE_LIMIT - sched / 2);
+ v = t3_read_reg(adap, A_TP_TM_PIO_DATA);
+ if (sched & 1)
+ v = (v & 0xffff) | (selected_cpt << 16) | (selected_bpt << 24);
+ else
+ v = (v & 0xffff0000) | selected_cpt | (selected_bpt << 8);
+ t3_write_reg(adap, A_TP_TM_PIO_DATA, v);
+ return 0;
+}
+
+static int tp_init(struct adapter *adap, const struct tp_params *p)
+{
+ int busy = 0;
+
+ tp_config(adap, p);
+ t3_set_vlan_accel(adap, 3, 0);
+
+ if (is_offload(adap)) {
+ tp_set_timers(adap, adap->params.vpd.cclk * 1000);
+ t3_write_reg(adap, A_TP_RESET, F_FLSTINITENABLE);
+ busy = t3_wait_op_done(adap, A_TP_RESET, F_FLSTINITENABLE,
+ 0, 1000, 5);
+ if (busy)
+ CH_ERR(adap, "TP initialization timed out\n");
+ }
+
+ if (!busy)
+ t3_write_reg(adap, A_TP_RESET, F_TPRESET);
+ return busy;
+}
+
+int t3_mps_set_active_ports(struct adapter *adap, unsigned int port_mask)
+{
+ if (port_mask & ~((1 << adap->params.nports) - 1))
+ return -EINVAL;
+ t3_set_reg_field(adap, A_MPS_CFG, F_PORT1ACTIVE | F_PORT0ACTIVE,
+ port_mask << S_PORT0ACTIVE);
+ return 0;
+}
+
+/*
+ * Perform the bits of HW initialization that are dependent on the number
+ * of available ports.
+ */
+static void init_hw_for_avail_ports(struct adapter *adap, int nports)
+{
+ int i;
+
+ if (nports == 1) {
+ t3_set_reg_field(adap, A_ULPRX_CTL, F_ROUND_ROBIN, 0);
+ t3_set_reg_field(adap, A_ULPTX_CONFIG, F_CFG_RR_ARB, 0);
+ t3_write_reg(adap, A_MPS_CFG, F_TPRXPORTEN | F_TPTXPORT0EN |
+ F_PORT0ACTIVE | F_ENFORCEPKT);
+ t3_write_reg(adap, A_PM1_TX_CFG, 0xc000c000);
+ } else {
+ t3_set_reg_field(adap, A_ULPRX_CTL, 0, F_ROUND_ROBIN);
+ t3_set_reg_field(adap, A_ULPTX_CONFIG, 0, F_CFG_RR_ARB);
+ t3_write_reg(adap, A_ULPTX_DMA_WEIGHT,
+ V_D1_WEIGHT(16) | V_D0_WEIGHT(16));
+ t3_write_reg(adap, A_MPS_CFG, F_TPTXPORT0EN | F_TPTXPORT1EN |
+ F_TPRXPORTEN | F_PORT0ACTIVE | F_PORT1ACTIVE |
+ F_ENFORCEPKT);
+ t3_write_reg(adap, A_PM1_TX_CFG, 0x80008000);
+ t3_set_reg_field(adap, A_TP_PC_CONFIG, 0, F_TXTOSQUEUEMAPMODE);
+ t3_write_reg(adap, A_TP_TX_MOD_QUEUE_REQ_MAP,
+ V_TX_MOD_QUEUE_REQ_MAP(0xaa));
+ for (i = 0; i < 16; i++)
+ t3_write_reg(adap, A_TP_TX_MOD_QUE_TABLE,
+ (i << 16) | 0x1010);
+ }
+}
+
+static int calibrate_xgm(struct adapter *adapter)
+{
+ if (uses_xaui(adapter)) {
+ unsigned int v, i;
+
+ for (i = 0; i < 5; ++i) {
+ t3_write_reg(adapter, A_XGM_XAUI_IMP, 0);
+ t3_read_reg(adapter, A_XGM_XAUI_IMP);
+ msleep(1);
+ v = t3_read_reg(adapter, A_XGM_XAUI_IMP);
+ if (!(v & (F_XGM_CALFAULT | F_CALBUSY))) {
+ t3_write_reg(adapter, A_XGM_XAUI_IMP,
+ V_XAUIIMP(G_CALIMP(v) >> 2));
+ return 0;
+ }
+ }
+ CH_ERR(adapter, "MAC calibration failed\n");
+ return -1;
+ } else {
+ t3_write_reg(adapter, A_XGM_RGMII_IMP,
+ V_RGMIIIMPPD(2) | V_RGMIIIMPPU(3));
+ t3_set_reg_field(adapter, A_XGM_RGMII_IMP, F_XGM_IMPSETUPDATE,
+ F_XGM_IMPSETUPDATE);
+ }
+ return 0;
+}
+
+static void calibrate_xgm_t3b(struct adapter *adapter)
+{
+ if (!uses_xaui(adapter)) {
+ t3_write_reg(adapter, A_XGM_RGMII_IMP, F_CALRESET |
+ F_CALUPDATE | V_RGMIIIMPPD(2) | V_RGMIIIMPPU(3));
+ t3_set_reg_field(adapter, A_XGM_RGMII_IMP, F_CALRESET, 0);
+ t3_set_reg_field(adapter, A_XGM_RGMII_IMP, 0,
+ F_XGM_IMPSETUPDATE);
+ t3_set_reg_field(adapter, A_XGM_RGMII_IMP, F_XGM_IMPSETUPDATE,
+ 0);
+ t3_set_reg_field(adapter, A_XGM_RGMII_IMP, F_CALUPDATE, 0);
+ t3_set_reg_field(adapter, A_XGM_RGMII_IMP, 0, F_CALUPDATE);
+ }
+}
+
+struct mc7_timing_params {
+ unsigned char ActToPreDly;
+ unsigned char ActToRdWrDly;
+ unsigned char PreCyc;
+ unsigned char RefCyc[5];
+ unsigned char BkCyc;
+ unsigned char WrToRdDly;
+ unsigned char RdToWrDly;
+};
+
+/*
+ * Write a value to a register and check that the write completed. These
+ * writes normally complete in a cycle or two, so one read should suffice.
+ * The very first read exists to flush the posted write to the device.
+ */
+static int wrreg_wait(struct adapter *adapter, unsigned int addr, u32 val)
+{
+ t3_write_reg(adapter, addr, val);
+ t3_read_reg(adapter, addr); /* flush */
+ if (!(t3_read_reg(adapter, addr) & F_BUSY))
+ return 0;
+ CH_ERR(adapter, "write to MC7 register 0x%x timed out\n", addr);
+ return -EIO;
+}
+
+static int mc7_init(struct mc7 *mc7, unsigned int mc7_clock, int mem_type)
+{
+ static const unsigned int mc7_mode[] = {
+ 0x632, 0x642, 0x652, 0x432, 0x442
+ };
+ static const struct mc7_timing_params mc7_timings[] = {
+ {12, 3, 4, {20, 28, 34, 52, 0}, 15, 6, 4},
+ {12, 4, 5, {20, 28, 34, 52, 0}, 16, 7, 4},
+ {12, 5, 6, {20, 28, 34, 52, 0}, 17, 8, 4},
+ {9, 3, 4, {15, 21, 26, 39, 0}, 12, 6, 4},
+ {9, 4, 5, {15, 21, 26, 39, 0}, 13, 7, 4}
+ };
+
+ u32 val;
+ unsigned int width, density, slow, attempts;
+ struct adapter *adapter = mc7->adapter;
+ const struct mc7_timing_params *p = &mc7_timings[mem_type];
+
+ val = t3_read_reg(adapter, mc7->offset + A_MC7_CFG);
+ slow = val & F_SLOW;
+ width = G_WIDTH(val);
+ density = G_DEN(val);
+
+ t3_write_reg(adapter, mc7->offset + A_MC7_CFG, val | F_IFEN);
+ val = t3_read_reg(adapter, mc7->offset + A_MC7_CFG); /* flush */
+ msleep(1);
+
+ if (!slow) {
+ t3_write_reg(adapter, mc7->offset + A_MC7_CAL, F_SGL_CAL_EN);
+ t3_read_reg(adapter, mc7->offset + A_MC7_CAL);
+ msleep(1);
+ if (t3_read_reg(adapter, mc7->offset + A_MC7_CAL) &
+ (F_BUSY | F_SGL_CAL_EN | F_CAL_FAULT)) {
+ CH_ERR(adapter, "%s MC7 calibration timed out\n",
+ mc7->name);
+ goto out_fail;
+ }
+ }
+
+ t3_write_reg(adapter, mc7->offset + A_MC7_PARM,
+ V_ACTTOPREDLY(p->ActToPreDly) |
+ V_ACTTORDWRDLY(p->ActToRdWrDly) | V_PRECYC(p->PreCyc) |
+ V_REFCYC(p->RefCyc[density]) | V_BKCYC(p->BkCyc) |
+ V_WRTORDDLY(p->WrToRdDly) | V_RDTOWRDLY(p->RdToWrDly));
+
+ t3_write_reg(adapter, mc7->offset + A_MC7_CFG,
+ val | F_CLKEN | F_TERM150);
+ t3_read_reg(adapter, mc7->offset + A_MC7_CFG); /* flush */
+
+ if (!slow)
+ t3_set_reg_field(adapter, mc7->offset + A_MC7_DLL, F_DLLENB,
+ F_DLLENB);
+ udelay(1);
+
+ val = slow ? 3 : 6;
+ if (wrreg_wait(adapter, mc7->offset + A_MC7_PRE, 0) ||
+ wrreg_wait(adapter, mc7->offset + A_MC7_EXT_MODE2, 0) ||
+ wrreg_wait(adapter, mc7->offset + A_MC7_EXT_MODE3, 0) ||
+ wrreg_wait(adapter, mc7->offset + A_MC7_EXT_MODE1, val))
+ goto out_fail;
+
+ if (!slow) {
+ t3_write_reg(adapter, mc7->offset + A_MC7_MODE, 0x100);
+ t3_set_reg_field(adapter, mc7->offset + A_MC7_DLL, F_DLLRST, 0);
+ udelay(5);
+ }
+
+ if (wrreg_wait(adapter, mc7->offset + A_MC7_PRE, 0) ||
+ wrreg_wait(adapter, mc7->offset + A_MC7_REF, 0) ||
+ wrreg_wait(adapter, mc7->offset + A_MC7_REF, 0) ||
+ wrreg_wait(adapter, mc7->offset + A_MC7_MODE,
+ mc7_mode[mem_type]) ||
+ wrreg_wait(adapter, mc7->offset + A_MC7_EXT_MODE1, val | 0x380) ||
+ wrreg_wait(adapter, mc7->offset + A_MC7_EXT_MODE1, val))
+ goto out_fail;
+
+ /* clock value is in KHz */
+ mc7_clock = mc7_clock * 7812 + mc7_clock / 2; /* ns */
+ mc7_clock /= 1000000; /* KHz->MHz, ns->us */
+
+ t3_write_reg(adapter, mc7->offset + A_MC7_REF,
+ F_PERREFEN | V_PREREFDIV(mc7_clock));
+ t3_read_reg(adapter, mc7->offset + A_MC7_REF); /* flush */
+
+ t3_write_reg(adapter, mc7->offset + A_MC7_ECC, F_ECCGENEN | F_ECCCHKEN);
+ t3_write_reg(adapter, mc7->offset + A_MC7_BIST_DATA, 0);
+ t3_write_reg(adapter, mc7->offset + A_MC7_BIST_ADDR_BEG, 0);
+ t3_write_reg(adapter, mc7->offset + A_MC7_BIST_ADDR_END,
+ (mc7->size << width) - 1);
+ t3_write_reg(adapter, mc7->offset + A_MC7_BIST_OP, V_OP(1));
+ t3_read_reg(adapter, mc7->offset + A_MC7_BIST_OP); /* flush */
+
+ attempts = 50;
+ do {
+ msleep(250);
+ val = t3_read_reg(adapter, mc7->offset + A_MC7_BIST_OP);
+ } while ((val & F_BUSY) && --attempts);
+ if (val & F_BUSY) {
+ CH_ERR(adapter, "%s MC7 BIST timed out\n", mc7->name);
+ goto out_fail;
+ }
+
+ /* Enable normal memory accesses. */
+ t3_set_reg_field(adapter, mc7->offset + A_MC7_CFG, 0, F_RDY);
+ return 0;
+
+out_fail:
+ return -1;
+}
+
+static void config_pcie(struct adapter *adap)
+{
+ static const u16 ack_lat[4][6] = {
+ {237, 416, 559, 1071, 2095, 4143},
+ {128, 217, 289, 545, 1057, 2081},
+ {73, 118, 154, 282, 538, 1050},
+ {67, 107, 86, 150, 278, 534}
+ };
+ static const u16 rpl_tmr[4][6] = {
+ {711, 1248, 1677, 3213, 6285, 12429},
+ {384, 651, 867, 1635, 3171, 6243},
+ {219, 354, 462, 846, 1614, 3150},
+ {201, 321, 258, 450, 834, 1602}
+ };
+
+ u16 val;
+ unsigned int log2_width, pldsize;
+ unsigned int fst_trn_rx, fst_trn_tx, acklat, rpllmt;
+
+ pci_read_config_word(adap->pdev,
+ adap->params.pci.pcie_cap_addr + PCI_EXP_DEVCTL,
+ &val);
+ pldsize = (val & PCI_EXP_DEVCTL_PAYLOAD) >> 5;
+ pci_read_config_word(adap->pdev,
+ adap->params.pci.pcie_cap_addr + PCI_EXP_LNKCTL,
+ &val);
+
+ fst_trn_tx = G_NUMFSTTRNSEQ(t3_read_reg(adap, A_PCIE_PEX_CTRL0));
+ fst_trn_rx = adap->params.rev == 0 ? fst_trn_tx :
+ G_NUMFSTTRNSEQRX(t3_read_reg(adap, A_PCIE_MODE));
+ log2_width = fls(adap->params.pci.width) - 1;
+ acklat = ack_lat[log2_width][pldsize];
+ if (val & 1) /* check LOsEnable */
+ acklat += fst_trn_tx * 4;
+ rpllmt = rpl_tmr[log2_width][pldsize] + fst_trn_rx * 4;
+
+ if (adap->params.rev == 0)
+ t3_set_reg_field(adap, A_PCIE_PEX_CTRL1,
+ V_T3A_ACKLAT(M_T3A_ACKLAT),
+ V_T3A_ACKLAT(acklat));
+ else
+ t3_set_reg_field(adap, A_PCIE_PEX_CTRL1, V_ACKLAT(M_ACKLAT),
+ V_ACKLAT(acklat));
+
+ t3_set_reg_field(adap, A_PCIE_PEX_CTRL0, V_REPLAYLMT(M_REPLAYLMT),
+ V_REPLAYLMT(rpllmt));
+
+ t3_write_reg(adap, A_PCIE_PEX_ERR, 0xffffffff);
+ t3_set_reg_field(adap, A_PCIE_CFG, F_PCIE_CLIDECEN, F_PCIE_CLIDECEN);
+}
+
+/*
+ * Initialize and configure T3 HW modules. This performs the
+ * initialization steps that need to be done once after a card is reset.
+ * MAC and PHY initialization is handled separarely whenever a port is enabled.
+ *
+ * fw_params are passed to FW and their value is platform dependent. Only the
+ * top 8 bits are available for use, the rest must be 0.
+ */
+int t3_init_hw(struct adapter *adapter, u32 fw_params)
+{
+ int err = -EIO, attempts = 100;
+ const struct vpd_params *vpd = &adapter->params.vpd;
+
+ if (adapter->params.rev > 0)
+ calibrate_xgm_t3b(adapter);
+ else if (calibrate_xgm(adapter))
+ goto out_err;
+
+ if (vpd->mclk) {
+ partition_mem(adapter, &adapter->params.tp);
+
+ if (mc7_init(&adapter->pmrx, vpd->mclk, vpd->mem_timing) ||
+ mc7_init(&adapter->pmtx, vpd->mclk, vpd->mem_timing) ||
+ mc7_init(&adapter->cm, vpd->mclk, vpd->mem_timing) ||
+ t3_mc5_init(&adapter->mc5, adapter->params.mc5.nservers,
+ adapter->params.mc5.nfilters,
+ adapter->params.mc5.nroutes))
+ goto out_err;
+ }
+
+ if (tp_init(adapter, &adapter->params.tp))
+ goto out_err;
+
+ t3_tp_set_coalescing_size(adapter,
+ min(adapter->params.sge.max_pkt_size,
+ MAX_RX_COALESCING_LEN), 1);
+ t3_tp_set_max_rxsize(adapter,
+ min(adapter->params.sge.max_pkt_size, 16384U));
+ ulp_config(adapter, &adapter->params.tp);
+
+ if (is_pcie(adapter))
+ config_pcie(adapter);
+ else
+ t3_set_reg_field(adapter, A_PCIX_CFG, 0, F_CLIDECEN);
+
+ t3_write_reg(adapter, A_PM1_RX_CFG, 0xf000f000);
+ init_hw_for_avail_ports(adapter, adapter->params.nports);
+ t3_sge_init(adapter, &adapter->params.sge);
+
+ t3_write_reg(adapter, A_CIM_HOST_ACC_DATA, vpd->uclk | fw_params);
+ t3_write_reg(adapter, A_CIM_BOOT_CFG,
+ V_BOOTADDR(FW_FLASH_BOOT_ADDR >> 2));
+ t3_read_reg(adapter, A_CIM_BOOT_CFG); /* flush */
+
+ do { /* wait for uP to initialize */
+ msleep(20);
+ } while (t3_read_reg(adapter, A_CIM_HOST_ACC_DATA) && --attempts);
+ if (!attempts)
+ goto out_err;
+
+ err = 0;
+out_err:
+ return err;
+}
+
+/**
+ * get_pci_mode - determine a card's PCI mode
+ * @adapter: the adapter
+ * @p: where to store the PCI settings
+ *
+ * Determines a card's PCI mode and associated parameters, such as speed
+ * and width.
+ */
+static void __devinit get_pci_mode(struct adapter *adapter,
+ struct pci_params *p)
+{
+ static unsigned short speed_map[] = { 33, 66, 100, 133 };
+ u32 pci_mode, pcie_cap;
+
+ pcie_cap = pci_find_capability(adapter->pdev, PCI_CAP_ID_EXP);
+ if (pcie_cap) {
+ u16 val;
+
+ p->variant = PCI_VARIANT_PCIE;
+ p->pcie_cap_addr = pcie_cap;
+ pci_read_config_word(adapter->pdev, pcie_cap + PCI_EXP_LNKSTA,
+ &val);
+ p->width = (val >> 4) & 0x3f;
+ return;
+ }
+
+ pci_mode = t3_read_reg(adapter, A_PCIX_MODE);
+ p->speed = speed_map[G_PCLKRANGE(pci_mode)];
+ p->width = (pci_mode & F_64BIT) ? 64 : 32;
+ pci_mode = G_PCIXINITPAT(pci_mode);
+ if (pci_mode == 0)
+ p->variant = PCI_VARIANT_PCI;
+ else if (pci_mode < 4)
+ p->variant = PCI_VARIANT_PCIX_MODE1_PARITY;
+ else if (pci_mode < 8)
+ p->variant = PCI_VARIANT_PCIX_MODE1_ECC;
+ else
+ p->variant = PCI_VARIANT_PCIX_266_MODE2;
+}
+
+/**
+ * init_link_config - initialize a link's SW state
+ * @lc: structure holding the link state
+ * @ai: information about the current card
+ *
+ * Initializes the SW state maintained for each link, including the link's
+ * capabilities and default speed/duplex/flow-control/autonegotiation
+ * settings.
+ */
+static void __devinit init_link_config(struct link_config *lc,
+ unsigned int caps)
+{
+ lc->supported = caps;
+ lc->requested_speed = lc->speed = SPEED_INVALID;
+ lc->requested_duplex = lc->duplex = DUPLEX_INVALID;
+ lc->requested_fc = lc->fc = PAUSE_RX | PAUSE_TX;
+ if (lc->supported & SUPPORTED_Autoneg) {
+ lc->advertising = lc->supported;
+ lc->autoneg = AUTONEG_ENABLE;
+ lc->requested_fc |= PAUSE_AUTONEG;
+ } else {
+ lc->advertising = 0;
+ lc->autoneg = AUTONEG_DISABLE;
+ }
+}
+
+/**
+ * mc7_calc_size - calculate MC7 memory size
+ * @cfg: the MC7 configuration
+ *
+ * Calculates the size of an MC7 memory in bytes from the value of its
+ * configuration register.
+ */
+static unsigned int __devinit mc7_calc_size(u32 cfg)
+{
+ unsigned int width = G_WIDTH(cfg);
+ unsigned int banks = !!(cfg & F_BKS) + 1;
+ unsigned int org = !!(cfg & F_ORG) + 1;
+ unsigned int density = G_DEN(cfg);
+ unsigned int MBs = ((256 << density) * banks) / (org << width);
+
+ return MBs << 20;
+}
+
+static void __devinit mc7_prep(struct adapter *adapter, struct mc7 *mc7,
+ unsigned int base_addr, const char *name)
+{
+ u32 cfg;
+
+ mc7->adapter = adapter;
+ mc7->name = name;
+ mc7->offset = base_addr - MC7_PMRX_BASE_ADDR;
+ cfg = t3_read_reg(adapter, mc7->offset + A_MC7_CFG);
+ mc7->size = mc7_calc_size(cfg);
+ mc7->width = G_WIDTH(cfg);
+}
+
+void mac_prep(struct cmac *mac, struct adapter *adapter, int index)
+{
+ mac->adapter = adapter;
+ mac->offset = (XGMAC0_1_BASE_ADDR - XGMAC0_0_BASE_ADDR) * index;
+ mac->nucast = 1;
+
+ if (adapter->params.rev == 0 && uses_xaui(adapter)) {
+ t3_write_reg(adapter, A_XGM_SERDES_CTRL + mac->offset,
+ is_10G(adapter) ? 0x2901c04 : 0x2301c04);
+ t3_set_reg_field(adapter, A_XGM_PORT_CFG + mac->offset,
+ F_ENRGMII, 0);
+ }
+}
+
+void early_hw_init(struct adapter *adapter, const struct adapter_info *ai)
+{
+ u32 val = V_PORTSPEED(is_10G(adapter) ? 3 : 2);
+
+ mi1_init(adapter, ai);
+ t3_write_reg(adapter, A_I2C_CFG, /* set for 80KHz */
+ V_I2C_CLKDIV(adapter->params.vpd.cclk / 80 - 1));
+ t3_write_reg(adapter, A_T3DBG_GPIO_EN,
+ ai->gpio_out | F_GPIO0_OEN | F_GPIO0_OUT_VAL);
+
+ if (adapter->params.rev == 0 || !uses_xaui(adapter))
+ val |= F_ENRGMII;
+
+ /* Enable MAC clocks so we can access the registers */
+ t3_write_reg(adapter, A_XGM_PORT_CFG, val);
+ t3_read_reg(adapter, A_XGM_PORT_CFG);
+
+ val |= F_CLKDIVRESET_;
+ t3_write_reg(adapter, A_XGM_PORT_CFG, val);
+ t3_read_reg(adapter, A_XGM_PORT_CFG);
+ t3_write_reg(adapter, XGM_REG(A_XGM_PORT_CFG, 1), val);
+ t3_read_reg(adapter, A_XGM_PORT_CFG);
+}
+
+/*
+ * Reset the adapter. PCIe cards lose their config space during reset, PCI-X
+ * ones don't.
+ */
+int t3_reset_adapter(struct adapter *adapter)
+{
+ int i;
+ uint16_t devid = 0;
+
+ if (is_pcie(adapter))
+ pci_save_state(adapter->pdev);
+ t3_write_reg(adapter, A_PL_RST, F_CRSTWRM | F_CRSTWRMMODE);
+
+ /*
+ * Delay. Give Some time to device to reset fully.
+ * XXX The delay time should be modified.
+ */
+ for (i = 0; i < 10; i++) {
+ msleep(50);
+ pci_read_config_word(adapter->pdev, 0x00, &devid);
+ if (devid == 0x1425)
+ break;
+ }
+
+ if (devid != 0x1425)
+ return -1;
+
+ if (is_pcie(adapter))
+ pci_restore_state(adapter->pdev);
+ return 0;
+}
+
+/*
+ * Initialize adapter SW state for the various HW modules, set initial values
+ * for some adapter tunables, take PHYs out of reset, and initialize the MDIO
+ * interface.
+ */
+int __devinit t3_prep_adapter(struct adapter *adapter,
+ const struct adapter_info *ai, int reset)
+{
+ int ret;
+ unsigned int i, j = 0;
+
+ get_pci_mode(adapter, &adapter->params.pci);
+
+ adapter->params.info = ai;
+ adapter->params.nports = ai->nports;
+ adapter->params.rev = t3_read_reg(adapter, A_PL_REV);
+ adapter->params.linkpoll_period = 0;
+ adapter->params.stats_update_period = is_10G(adapter) ?
+ MAC_STATS_ACCUM_SECS : (MAC_STATS_ACCUM_SECS * 10);
+ adapter->params.pci.vpd_cap_addr =
+ pci_find_capability(adapter->pdev, PCI_CAP_ID_VPD);
+ ret = get_vpd_params(adapter, &adapter->params.vpd);
+ if (ret < 0)
+ return ret;
+
+ if (reset && t3_reset_adapter(adapter))
+ return -1;
+
+ t3_sge_prep(adapter, &adapter->params.sge);
+
+ if (adapter->params.vpd.mclk) {
+ struct tp_params *p = &adapter->params.tp;
+
+ mc7_prep(adapter, &adapter->pmrx, MC7_PMRX_BASE_ADDR, "PMRX");
+ mc7_prep(adapter, &adapter->pmtx, MC7_PMTX_BASE_ADDR, "PMTX");
+ mc7_prep(adapter, &adapter->cm, MC7_CM_BASE_ADDR, "CM");
+
+ p->nchan = ai->nports;
+ p->pmrx_size = t3_mc7_size(&adapter->pmrx);
+ p->pmtx_size = t3_mc7_size(&adapter->pmtx);
+ p->cm_size = t3_mc7_size(&adapter->cm);
+ p->chan_rx_size = p->pmrx_size / 2; /* only 1 Rx channel */
+ p->chan_tx_size = p->pmtx_size / p->nchan;
+ p->rx_pg_size = 64 * 1024;
+ p->tx_pg_size = is_10G(adapter) ? 64 * 1024 : 16 * 1024;
+ p->rx_num_pgs = pm_num_pages(p->chan_rx_size, p->rx_pg_size);
+ p->tx_num_pgs = pm_num_pages(p->chan_tx_size, p->tx_pg_size);
+ p->ntimer_qs = p->cm_size >= (128 << 20) ||
+ adapter->params.rev > 0 ? 12 : 6;
+
+ adapter->params.mc5.nservers = DEFAULT_NSERVERS;
+ adapter->params.mc5.nfilters = adapter->params.rev > 0 ?
+ DEFAULT_NFILTERS : 0;
+ adapter->params.mc5.nroutes = 0;
+ t3_mc5_prep(adapter, &adapter->mc5, MC5_MODE_144_BIT);
+
+ init_mtus(adapter->params.mtus);
+ init_cong_ctrl(adapter->params.a_wnd, adapter->params.b_wnd);
+ }
+
+ early_hw_init(adapter, ai);
+
+ for_each_port(adapter, i) {
+ u8 hw_addr[6];
+ struct port_info *p = adap2pinfo(adapter, i);
+
+ while (!adapter->params.vpd.port_type[j])
+ ++j;
+
+ p->port_type = &port_types[adapter->params.vpd.port_type[j]];
+ p->port_type->phy_prep(&p->phy, adapter, ai->phy_base_addr + j,
+ ai->mdio_ops);
+ mac_prep(&p->mac, adapter, j);
+ ++j;
+
+ /*
+ * The VPD EEPROM stores the base Ethernet address for the
+ * card. A port's address is derived from the base by adding
+ * the port's index to the base's low octet.
+ */
+ memcpy(hw_addr, adapter->params.vpd.eth_base, 5);
+ hw_addr[5] = adapter->params.vpd.eth_base[5] + i;
+
+ memcpy(adapter->port[i]->dev_addr, hw_addr,
+ ETH_ALEN);
+#ifdef ETHTOOL_GPERMADDR
+ memcpy(adapter->port[i]->perm_addr, hw_addr,
+ ETH_ALEN);
+#endif
+ init_link_config(&p->link_config, p->port_type->caps);
+ p->phy.ops->power_down(&p->phy, 1);
+ if (!(p->port_type->caps & SUPPORTED_IRQ))
+ adapter->params.linkpoll_period = 10;
+ }
+
+ return 0;
+}
+
+void t3_led_ready(struct adapter *adapter)
+{
+ t3_set_reg_field(adapter, A_T3DBG_GPIO_EN, F_GPIO0_OUT_VAL,
+ F_GPIO0_OUT_VAL);
+}
> +void t3_port_intr_disable(struct adapter *adapter, int idx)
> +{
> + struct cphy *phy = &adap2pinfo(adapter, idx)->phy;
> +
> + t3_write_reg(adapter, XGM_REG(A_XGM_INT_ENABLE, idx), 0);
> + phy->ops->intr_disable(phy);
you seem to be missing a pci posting flush here....
--
if you want to mail me at work (you don't), use arjan (at) linux.intel.com
Test the interaction between Linux and your BIOS via http://www.linuxfirmwarekit.org
Arjan van de Ven wrote:
>> +void t3_port_intr_disable(struct adapter *adapter, int idx)
>> +{
>> + struct cphy *phy = &adap2pinfo(adapter, idx)->phy;
>> +
>> + t3_write_reg(adapter, XGM_REG(A_XGM_INT_ENABLE, idx), 0);
>> + phy->ops->intr_disable(phy);
>>
>
> you seem to be missing a pci posting flush here....
>
Thanks for catching this. Will fix.