Hi
I have system running the 2.6.20 kernel, and I am trying to use an eSATA
disk with it. The hardware in question is a 'NexStar-3' eSATA
enclosure, and inside it is a Seagate Barracuda 7200.10 750Gb SATA drive.
I am hooking this up to an ASUS M2N-MX motherboard using the SATA to
eSATA bracket that comes with the enclosure.
When I boot up the machine the disk is recognized, but it immediately
has device errors and 'slow to respond' errors. When I use fdisk to
write a partition table it seems to give up entirely. Is this a known
problem, or is there something I can try?
I am not subscribed to the mailing list so I would appreciate a CC on
any replies.
Thanks,
Tom
Relevant lines from syslog...
Jun 3 15:33:57 fawkes Uniform Multi-Platform E-IDE driver Revision:
7.00alpha2
Jun 3 15:33:57 fawkes ide: Assuming 33MHz system bus speed for PIO
modes; override with idebus=xx
Jun 3 15:33:57 fawkes NFORCE-MCP61: IDE controller at PCI slot 0000:00:06.0
Jun 3 15:33:57 fawkes NFORCE-MCP61: chipset revision 162
Jun 3 15:33:57 fawkes NFORCE-MCP61: not 100% native mode: will probe
irqs later
Jun 3 15:33:57 fawkes NFORCE-MCP61: BIOS didn't set cable bits
correctly. Enabling workaround.
Jun 3 15:33:57 fawkes NFORCE-MCP61: 0000:00:06.0 (rev a2) UDMA133
controller
Jun 3 15:33:57 fawkes ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings:
hda:DMA, hdb:pio
Jun 3 15:33:57 fawkes Probing IDE interface ide0...
Jun 3 15:33:57 fawkes hda: WDC WD2500JB-00GVA0, ATA DISK drive
Jun 3 15:33:57 fawkes ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Jun 3 15:33:57 fawkes Probing IDE interface ide1...
Jun 3 15:33:57 fawkes hda: max request size: 512KiB
Jun 3 15:33:57 fawkes hda: 488397168 sectors (250059 MB) w/8192KiB
Cache, CHS=30401/255/63<6>hda: hw_config=604d
Jun 3 15:33:57 fawkes , UDMA(100)
Jun 3 15:33:57 fawkes hda: cache flushes supported
Jun 3 15:33:57 fawkes hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
Jun 3 15:33:57 fawkes 3ware Storage Controller device driver for Linux
v1.26.02.002.
Jun 3 15:33:57 fawkes sata_nv 0000:00:08.0: version 3.2
Jun 3 15:33:57 fawkes ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 22
Jun 3 15:33:57 fawkes ACPI: PCI Interrupt 0000:00:08.0[A] -> Link
[LSA0] -> GSI 22 (level, low) -> IRQ 18
Jun 3 15:33:57 fawkes PCI: Setting latency timer of device 0000:00:08.0
to 64
Jun 3 15:33:57 fawkes ata1: SATA max UDMA/133 cmd 0xD400 ctl 0xD082
bmdma 0xC880 irq 18
Jun 3 15:33:57 fawkes ata2: SATA max UDMA/133 cmd 0xD000 ctl 0xCC02
bmdma 0xC888 irq 18
Jun 3 15:33:57 fawkes scsi0 : sata_nv
Jun 3 15:33:57 fawkes ata1: SATA link up 1.5 Gbps (SStatus 113 SControl
300)
Jun 3 15:33:57 fawkes ata1.00: ATA-7, max UDMA/133, 1465149168 sectors:
LBA48 NCQ (depth 0/32)
Jun 3 15:33:57 fawkes ata1.00: ata1: dev 0 multi count 16
Jun 3 15:33:57 fawkes ata1.00: configured for UDMA/133
Jun 3 15:33:57 fawkes scsi1 : sata_nv
Jun 3 15:33:57 fawkes ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
300)
Jun 3 15:33:57 fawkes ata2.00: ATA-7, max UDMA/133, 1465149168 sectors:
LBA48 NCQ (depth 0/32)
Jun 3 15:33:57 fawkes ata2.00: ata2: dev 0 multi count 16
Jun 3 15:33:57 fawkes ata2.00: configured for UDMA/133
Jun 3 15:33:57 fawkes scsi 0:0:0:0: Direct-Access ATA
ST3750640AS 3.AA PQ: 0 ANSI: 5
Jun 3 15:33:57 fawkes SCSI device sda: 1465149168 512-byte hdwr sectors
(750156 MB)
Jun 3 15:33:57 fawkes sda: Write Protect is off
Jun 3 15:33:57 fawkes sda: Mode Sense: 00 3a 00 00
Jun 3 15:33:57 fawkes SCSI device sda: write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Jun 3 15:33:57 fawkes SCSI device sda: 1465149168 512-byte hdwr sectors
(750156 MB)
Jun 3 15:33:57 fawkes sda: Write Protect is off
Jun 3 15:33:57 fawkes sda: Mode Sense: 00 3a 00 00
Jun 3 15:33:57 fawkes SCSI device sda: write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Jun 3 15:33:57 fawkes sda: sda1 sda2 sda3 sda4 < sda5 >
Jun 3 15:33:57 fawkes sd 0:0:0:0: Attached scsi disk sda
Jun 3 15:33:57 fawkes sd 0:0:0:0: Attached scsi generic sg0 type 0
Jun 3 15:33:57 fawkes scsi 1:0:0:0: Direct-Access ATA
ST3750640AS 3.AA PQ: 0 ANSI: 5
Jun 3 15:33:57 fawkes SCSI device sdb: 1465149168 512-byte hdwr sectors
(750156 MB)
Jun 3 15:33:57 fawkes sdb: Write Protect is off
Jun 3 15:33:57 fawkes sdb: Mode Sense: 00 3a 00 00
Jun 3 15:33:57 fawkes SCSI device sdb: write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Jun 3 15:33:57 fawkes SCSI device sdb: 1465149168 512-byte hdwr sectors
(750156 MB)
Jun 3 15:33:57 fawkes sdb: Write Protect is off
Jun 3 15:33:57 fawkes sdb: Mode Sense: 00 3a 00 00
Jun 3 15:33:57 fawkes SCSI device sdb: write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Jun 3 15:33:57 fawkes sdb: sdb1
Jun 3 15:33:57 fawkes sd 1:0:0:0: Attached scsi disk sdb
Jun 3 15:33:57 fawkes sd 1:0:0:0: Attached scsi generic sg1 type 0
Jun 3 15:33:57 fawkes ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 21
Jun 3 15:33:57 fawkes ACPI: PCI Interrupt 0000:00:08.1[B] -> Link
[LSA1] -> GSI 21 (level, low) -> IRQ 19
Jun 3 15:33:57 fawkes PCI: Setting latency timer of device 0000:00:08.1
to 64
Jun 3 15:33:57 fawkes ata3: SATA max UDMA/133 cmd 0xC800 ctl 0xC482
bmdma 0xC000 irq 19
Jun 3 15:33:57 fawkes ata4: SATA max UDMA/133 cmd 0xC400 ctl 0xC082
bmdma 0xC008 irq 19
Jun 3 15:33:57 fawkes scsi2 : sata_nv
Jun 3 15:33:57 fawkes ata3: port is slow to respond, please be patient
(Status 0xd0)
Jun 3 15:33:57 fawkes ata3: port failed to respond (30 secs, Status 0xd0)
Jun 3 15:33:57 fawkes ata3: SATA link up 3.0 Gbps (SStatus 123 SControl
300)
Jun 3 15:33:57 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:33:57 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:33:57 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:33:57 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:33:57 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:33:57 fawkes ata3.00: ATA-7, max UDMA/133, 1465149168 sectors:
LBA48 NCQ (depth 0/32)
Jun 3 15:33:57 fawkes ata3.00: ata3: dev 0 multi count 16
Jun 3 15:33:57 fawkes ata3.00: Drive reports diagnostics failure. This
may indicate a drive
Jun 3 15:33:57 fawkes ata3.00: fault or invalid emulation. Contact
drive vendor for information.
Jun 3 15:33:57 fawkes ata3.00: configured for UDMA/133
Jun 3 15:33:57 fawkes scsi3 : sata_nv
Jun 3 15:33:57 fawkes ata4: SATA link down (SStatus 0 SControl 300)
Jun 3 15:33:57 fawkes ATA: abnormal status 0x7F on port 0xC407
Jun 3 15:33:57 fawkes scsi 2:0:0:0: Direct-Access ATA
ST3750640AS 3.AA PQ: 0 ANSI: 5
Jun 3 15:33:57 fawkes SCSI device sdc: 1465149168 512-byte hdwr sectors
(750156 MB)
Jun 3 15:33:57 fawkes sdc: Write Protect is off
Jun 3 15:33:57 fawkes sdc: Mode Sense: 00 3a 00 00
Jun 3 15:33:57 fawkes SCSI device sdc: write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Jun 3 15:33:57 fawkes SCSI device sdc: 1465149168 512-byte hdwr sectors
(750156 MB)
Jun 3 15:33:57 fawkes sdc: Write Protect is off
Jun 3 15:33:57 fawkes sdc: Mode Sense: 00 3a 00 00
Jun 3 15:33:57 fawkes SCSI device sdc: write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Jun 3 15:33:57 fawkes sdc: unknown partition table
Jun 3 15:33:57 fawkes sd 2:0:0:0: Attached scsi disk sdc
Jun 3 15:33:57 fawkes sd 2:0:0:0: Attached scsi generic sg2 type 0
later after trying to write new partition information...
Jun 3 15:35:58 fawkes ata3: port failed to respond (30 secs, Status 0xd0)
Jun 3 15:35:58 fawkes ata3: SATA link up 3.0 Gbps (SStatus 123 SControl
300)
Jun 3 15:35:58 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:35:58 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:35:58 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:35:58 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:35:58 fawkes ATA: abnormal status 0xD0 on port 0xC807
Jun 3 15:36:28 fawkes ata3.00: qc timeout (cmd 0xec)
Jun 3 15:36:28 fawkes ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
Jun 3 15:36:28 fawkes ata3.00: revalidation failed (errno=-5)
Jun 3 15:36:28 fawkes ata3: failed to recover some devices, retrying in
5 secs
Jun 3 15:36:33 fawkes ata3: hard resetting port
Jun 3 15:36:40 fawkes ata3: port is slow to respond, please be patient
(Status 0xd0)