I'm running into the same issue reported here:
<http://readlist.com/lists/vger.kernel.org/linux-kernel/72/361184.html>
I am using the ata_piix module. If I read the docs correctly, I should
be able to use ahci as well; I need to rebuild the kernel though (debian
insists on putting ata_piix into the initrd....)
dionysus:~# ls -l /sys/block/sd[abcde]/device/queue_depth
-r--r--r-- 1 root root 4096 2007-09-01 06:00
/sys/block/sda/device/queue_depth
-r--r--r-- 1 root root 4096 2007-09-01 06:00
/sys/block/sdb/device/queue_depth
-r--r--r-- 1 root root 4096 2007-09-01 06:00
/sys/block/sdc/device/queue_depth
-r--r--r-- 1 root root 4096 2007-09-01 06:00
/sys/block/sdd/device/queue_depth
-r--r--r-- 1 root root 4096 2007-09-01 06:00
/sys/block/sde/device/queue_depth
If I change the perms to rw, I get an Input/Output error. AFAICT, the
drives support queueing, but it's disabled.
dionysus:~# uname -a
Linux dionysus 2.6.22.6 #1 SMP Fri Aug 31 14:24:17 PDT 2007 x86_64 GNU/Linux
libata version 2.21 loaded.
ata_piix 0000:00:1f.2: version 2.11
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6
bmdma 0x000000000001f000 irq 14
ata2: SATA max UDMA/133 cmd 0x0000000000010170 ctl 0x0000000000010376
bmdma 0x000000000001f008 irq 15
ata1.00: Host Protected Area detected:
ata1.00: ATA-7: ST3400620AS, 3.AAC, max UDMA/133
ata1.00: 781420655 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.01: Host Protected Area detected:
ata1.01: ATA-7: ST3400620AS, 3.AAC, max UDMA/133
ata1.01: 781420655 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: Host Protected Area detected:
ata1.00: configured for UDMA/133
ata1.01: Host Protected Area detected:
ata1.01: configured for UDMA/133
ata2.00: ATA-7: ST3400620AS, 3.AAC, max UDMA/133
ata2.00: 781422768 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.01: ATA-7: ST3400620AS, 3.AAC, max UDMA/133
ata2.01: 781422768 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
ata2.01: configured for UDMA/133
dionysus:~# lspci -s 00:1f.2 -vvv
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family)
Serial ATA Storage Controller IDE (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Giga-byte Technology Unknown device b002
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at f000 [size=16]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
--
o__
,>/'_ o__
(_)\(_) ,>/'_ o__
Yan Seiner (_)\(_) ,>/'_ o__ o__
Certified Personal Trainer (_)\(_) ,>/'_ ,>/'_
Licensed Professional Engineer (_)\(_) (_)\(_)
Linux stuff has made big progress over the competition. When things sit and don't start right away, we have a watch, and those poor guys have to settle for an hourglass.
Yan Seiner wrote:
> I'm running into the same issue reported here:
>
> <http://readlist.com/lists/vger.kernel.org/linux-kernel/72/361184.html>
>
> I am using the ata_piix module. If I read the docs correctly, I should
> be able to use ahci as well; I need to rebuild the kernel though (debian
> insists on putting ata_piix into the initrd....)
>
> dionysus:~# ls -l /sys/block/sd[abcde]/device/queue_depth
> -r--r--r-- 1 root root 4096 2007-09-01 06:00
> /sys/block/sda/device/queue_depth
> -r--r--r-- 1 root root 4096 2007-09-01 06:00
> /sys/block/sdb/device/queue_depth
> -r--r--r-- 1 root root 4096 2007-09-01 06:00
> /sys/block/sdc/device/queue_depth
> -r--r--r-- 1 root root 4096 2007-09-01 06:00
> /sys/block/sdd/device/queue_depth
> -r--r--r-- 1 root root 4096 2007-09-01 06:00
> /sys/block/sde/device/queue_depth
>
> If I change the perms to rw, I get an Input/Output error. AFAICT, the
> drives support queueing, but it's disabled.
ata_piix does not support NCQ. You have to use AHCI mode for that.
--
Robert Hancock Saskatoon, SK, Canada
To email, remove "nospam" from [email protected]
Home Page: http://www.roberthancock.com/