These are i.MX6DualLite/Solo based single board computers used
in various Y Soft products.
Cc: Andrew Lunn <[email protected]>
Signed-off-by: Michal Vokáč <[email protected]>
---
Changes since v2:
- New patch
Documentation/devicetree/bindings/arm/fsl.yaml | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index a4d625d..b3908a0 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -94,6 +94,9 @@ properties:
- fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board
- technologic,imx6dl-ts4900
- technologic,imx6dl-ts7970
+ - ysoft,imx6dl-yapp4-draco # i.MX6 DualLite Y Soft IOTA Draco board
+ - ysoft,imx6dl-yapp4-hydra # i.MX6 DualLite Y Soft IOTA Hydra board
+ - ysoft,imx6dl-yapp4-ursa # i.MX6 Solo Y Soft IOTA Ursa board
- const: fsl,imx6dl
- description: i.MX6SL based Boards
--
2.1.4
These are i.MX6S/DL based SBCs embedded in various Y Soft products.
All share the same board design but have slightly different HW
configuration.
Ursa
- i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
- parallel WVGA 7" LCD with touch panel
- 1x Eth (QCA8334 switch)
- USB OTG
- USB host (micro-B)
Draco
- i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
- parallel WVGA 7" LCD with touch panel
- 2x Eth (QCA8334 switch)
- USB OTG
- USB host (micro-B)
- RGB LED (I2C LP5562)
- 3.5mm audio jack + codec (LM49350)
Hydra
- i.MX6DL SoC, 2GB RAM DDR3, 4GB eMMC, microSD
- I2C OLED display, capacitive matrix keys
- 2x Eth (QCA8334 switch)
- USB OTG
- RGB LED (I2C LP5562)
- 3.5mm audio jack + codec (LM49350)
- HDMI
- miniPCIe slot
Cc: Andrew Lunn <[email protected]>
Signed-off-by: Michal Vokáč <[email protected]>
---
Changes since v2:
- Remove cpus {/delete-node/ cpu@1;}; node from i.MX6Solo based board. (Fabio)
- Use "device_type = "memory";" in memory nodes. (Fabio)
- Use GPIO_ACTIVE_LOW for fec phy-reset-gpios. (Fabio)
- Use "-" in node names. (Rob)
- Remove label from led-controller node. (Rob)
Changes since v1:
- Enable HDMI on Hydra board.
- Move regulators to the root node and remove simple-bus property. (Rob)
- Remove reg and unit-address property from regulators. (Rob)
- Use correct names for led-controller and pmic node. (Rob)
- Use wakeup-source instead of deprecated enable-sdio-wakeup. (Shawn)
arch/arm/boot/dts/Makefile | 3 +
arch/arm/boot/dts/imx6dl-yapp4-common.dtsi | 594 +++++++++++++++++++++++++++++
arch/arm/boot/dts/imx6dl-yapp4-draco.dts | 58 +++
arch/arm/boot/dts/imx6dl-yapp4-hydra.dts | 50 +++
arch/arm/boot/dts/imx6dl-yapp4-ursa.dts | 54 +++
5 files changed, 759 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-draco.dts
create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index bd40148..c0a9b89 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -445,6 +445,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-wandboard.dtb \
imx6dl-wandboard-revb1.dtb \
imx6dl-wandboard-revd1.dtb \
+ imx6dl-yapp4-draco.dtb \
+ imx6dl-yapp4-hydra.dtb \
+ imx6dl-yapp4-ursa.dtb \
imx6q-apalis-eval.dtb \
imx6q-apalis-ixora.dtb \
imx6q-apalis-ixora-v1.1.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
new file mode 100644
index 0000000..48c2847
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
@@ -0,0 +1,594 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 32 64 128 255>;
+ default-brightness-level = <32>;
+ num-interpolated-steps = <8>;
+ power-supply = <&sw2_reg>;
+ status = "disabled";
+ };
+
+ lcd_display: display {
+ compatible = "fsl,imx-parallel-display";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interface-pix-fmt = "rgb24";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1>;
+ status = "disabled";
+
+ port@0 {
+ reg = <0>;
+
+ lcd_display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ lcd_display_out: endpoint {
+ remote-endpoint = <&lcd_panel_in>;
+ };
+ };
+ };
+
+ panel: panel {
+ compatible = "dataimage,scf0700c48ggu18";
+ power-supply = <&sw2_reg>;
+ status = "disabled";
+
+ port {
+ lcd_panel_in: endpoint {
+ remote-endpoint = <&lcd_display_out>;
+ };
+ };
+ };
+
+ reg_usb_h1_vbus: reg-usb-h1-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1_vbus>;
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ status = "disabled";
+ };
+
+ reg_usb_otg_vbus: reg-usb-otg-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg_vbus>;
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ status = "okay";
+ };
+
+ reg_pcie: reg-pcie {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie_reg>;
+ regulator-name = "MPCIE_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ status = "disabled";
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <20>;
+ phy-supply = <&sw2_reg>;
+ phy-handle = <ðphy0>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy_port2: phy@1 {
+ reg = <1>;
+ };
+
+ phy_port3: phy@2 {
+ reg = <2>;
+ };
+
+ switch@0 {
+ compatible = "qca,qca8334";
+ reg = <0>;
+
+ switch_ports: ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: port@0 {
+ reg = <0>;
+ label = "cpu";
+ phy-mode = "rgmii";
+ ethernet = <&fec>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "eth2";
+ phy-handle = <&phy_port2>;
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "eth1";
+ phy-handle = <&phy_port3>;
+ };
+ };
+ };
+ };
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hdmi_cec>;
+ ddc-i2c-bus = <&i2c2>;
+ status = "disabled";
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ eeprom@57 {
+ compatible = "atmel,24c128";
+ reg = <0x57>;
+ pagesize = <64>;
+ status = "okay";
+ };
+
+ leds: led-controller@30 {
+ compatible = "ti,lp5562";
+ reg = <0x30>;
+ clock-mode = /bits/ 8 <1>;
+ status = "disabled";
+
+ chan0 {
+ chan-name = "R";
+ led-cur = /bits/ 8 <0x20>;
+ max-cur = /bits/ 8 <0x60>;
+ };
+
+ chan1 {
+ chan-name = "G";
+ led-cur = /bits/ 8 <0x20>;
+ max-cur = /bits/ 8 <0x60>;
+ };
+
+ chan2 {
+ chan-name = "B";
+ led-cur = /bits/ 8 <0x20>;
+ max-cur = /bits/ 8 <0x60>;
+ };
+
+ chan3 {
+ chan-name = "W";
+ led-cur = /bits/ 8 <0x0>;
+ max-cur = /bits/ 8 <0x0>;
+ };
+ };
+
+ pmic@8 {
+ compatible = "fsl,pfuze200";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ reg = <0x8>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+
+ touchscreen: touchscreen@5c {
+ compatible = "pixcir,pixcir_tangoc";
+ reg = <0x5c>;
+ pinctrl-0 = <&pinctrl_touch>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+ attb-gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>;
+ reset-gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ status = "disabled";
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "disabled";
+
+ gpio_oled: gpio@41 {
+ compatible = "nxp,pca9536";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x41>;
+ vcc-supply = <&sw2_reg>;
+ status = "disabled";
+ };
+
+ oled: oled@3d {
+ compatible = "solomon,ssd1305fb-i2c";
+ reg = <0x3d>;
+ solomon,height = <64>;
+ solomon,width = <128>;
+ solomon,page-offset = <0>;
+ solomon,prechargep2 = <15>;
+ reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
+ vbat-supply = <&sw2_reg>;
+ status = "disabled";
+ };
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b020
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b020
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b020
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b020
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b020
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b020
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b020
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b020
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b020
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b020
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b020
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b020
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b020
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b020
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b010
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b010
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b098
+ >;
+ };
+
+ pinctrl_hdmi_cec: hdmicecgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1b898
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b899
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b899
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b899
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b899
+ >;
+ };
+
+ pinctrl_ipu1: ipu1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b098
+ MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x1b098
+ MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b098
+ >;
+ };
+
+ pinctrl_pcie_reg: pciereggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b098
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b098
+ >;
+ };
+
+ pinctrl_backlight_pwm: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x8
+ >;
+ };
+
+ pinctrl_touch: touchgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b098
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b098
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0a8
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0a8
+ >;
+ };
+
+ pinctrl_usbh1: usbh1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D30__USB_H1_OC 0x1b098
+ >;
+ };
+
+ pinctrl_usbh1_vbus: usbh1-vbus {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x98
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1b098
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b098
+ >;
+ };
+
+ pinctrl_usbotg_vbus: usbotg-vbus {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x98
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x1b018
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1b018
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ >;
+ };
+
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x1f069
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10069
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17069
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17069
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17069
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17069
+ MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17069
+ MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17069
+ MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17069
+ MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17069
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__WDOG2_B 0x1b0b0
+ >;
+ };
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&lcd_display_in>;
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio7 12 GPIO_ACTIVE_LOW>;
+ vpcie-supply = <®_pcie>;
+ status = "disabled";
+};
+
+&pwm1 {
+ #pwm-cells = <3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight_pwm>;
+ status = "disabled";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usbh1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1>;
+ vbus-supply = <®_usb_h1_vbus>;
+ status = "disabled";
+};
+
+&usbotg {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ vbus-supply = <®_usb_otg_vbus>;
+ srp-disable;
+ hnp-disable;
+ adp-disable;
+ status = "okay";
+};
+
+&usbphy1 {
+ fsl,tx-d-cal = <106>;
+ status = "okay";
+};
+
+&usbphy2 {
+ fsl,tx-d-cal = <109>;
+ status = "disabled";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <4>;
+ cd-gpios = <&gpio7 8 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ wakeup-source;
+ vmmc-supply = <&sw2_reg>;
+ status = "disabled";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <8>;
+ non-removable;
+ no-1-8-v;
+ keep-power-in-suspend;
+ vmmc-supply = <&sw2_reg>;
+ status = "okay";
+};
+
+&wdog1 {
+ status = "disabled";
+};
+
+&wdog2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-draco.dts b/arch/arm/boot/dts/imx6dl-yapp4-draco.dts
new file mode 100644
index 0000000..a38c407
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-yapp4-draco.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6dl-yapp4-common.dtsi"
+
+/ {
+ model = "Y Soft IOTA Draco i.MX6Solo board";
+ compatible = "ysoft,imx6dl-yapp4-draco", "fsl,imx6dl";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x20000000>;
+ };
+};
+
+&backlight {
+ status = "okay";
+};
+
+&lcd_display {
+ status = "okay";
+};
+
+&leds {
+ status = "okay";
+};
+
+&panel {
+ status = "okay";
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+®_usb_h1_vbus {
+ status = "okay";
+};
+
+&touchscreen {
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+&usbphy2 {
+ status = "okay";
+};
+
+&usdhc3 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-hydra.dts b/arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
new file mode 100644
index 0000000..f979270
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6dl-yapp4-common.dtsi"
+
+/ {
+ model = "Y Soft IOTA Hydra i.MX6DualLite board";
+ compatible = "ysoft,imx6dl-yapp4-hydra", "fsl,imx6dl";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x80000000>;
+ };
+};
+
+&gpio_oled {
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&i2c3 {
+ status = "okay";
+};
+
+&leds {
+ status = "okay";
+};
+
+&oled {
+ status = "okay";
+};
+
+&pcie {
+ status = "okay";
+};
+
+®_pcie {
+ status = "okay";
+};
+
+&usdhc3 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-ursa.dts b/arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
new file mode 100644
index 0000000..0d594e4
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6dl-yapp4-common.dtsi"
+
+/ {
+ model = "Y Soft IOTA Ursa i.MX6Solo board";
+ compatible = "ysoft,imx6dl-yapp4-ursa", "fsl,imx6dl";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x20000000>;
+ };
+};
+
+&backlight {
+ status = "okay";
+};
+
+&lcd_display {
+ status = "okay";
+};
+
+&panel {
+ status = "okay";
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+®_usb_h1_vbus {
+ status = "okay";
+};
+
+&switch_ports {
+ /delete-node/ port@2;
+};
+
+&touchscreen {
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+&usbphy2 {
+ status = "okay";
+};
--
2.1.4
On Thu, Jan 10, 2019 at 04:20:51PM +0000, Vokáč Michal wrote:
> These are i.MX6S/DL based SBCs embedded in various Y Soft products.
> All share the same board design but have slightly different HW
> configuration.
>
> Ursa
> - i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
> - parallel WVGA 7" LCD with touch panel
> - 1x Eth (QCA8334 switch)
> - USB OTG
> - USB host (micro-B)
>
> Draco
> - i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
> - parallel WVGA 7" LCD with touch panel
> - 2x Eth (QCA8334 switch)
> - USB OTG
> - USB host (micro-B)
> - RGB LED (I2C LP5562)
> - 3.5mm audio jack + codec (LM49350)
>
> Hydra
> - i.MX6DL SoC, 2GB RAM DDR3, 4GB eMMC, microSD
> - I2C OLED display, capacitive matrix keys
> - 2x Eth (QCA8334 switch)
> - USB OTG
> - RGB LED (I2C LP5562)
> - 3.5mm audio jack + codec (LM49350)
> - HDMI
> - miniPCIe slot
>
> Cc: Andrew Lunn <[email protected]>
> Signed-off-by: Michal Vokáč <[email protected]>
> ---
> Changes since v2:
> - Remove cpus {/delete-node/ cpu@1;}; node from i.MX6Solo based board. (Fabio)
> - Use "device_type = "memory";" in memory nodes. (Fabio)
> - Use GPIO_ACTIVE_LOW for fec phy-reset-gpios. (Fabio)
> - Use "-" in node names. (Rob)
> - Remove label from led-controller node. (Rob)
>
> Changes since v1:
> - Enable HDMI on Hydra board.
> - Move regulators to the root node and remove simple-bus property. (Rob)
> - Remove reg and unit-address property from regulators. (Rob)
> - Use correct names for led-controller and pmic node. (Rob)
> - Use wakeup-source instead of deprecated enable-sdio-wakeup. (Shawn)
>
> arch/arm/boot/dts/Makefile | 3 +
> arch/arm/boot/dts/imx6dl-yapp4-common.dtsi | 594 +++++++++++++++++++++++++++++
> arch/arm/boot/dts/imx6dl-yapp4-draco.dts | 58 +++
> arch/arm/boot/dts/imx6dl-yapp4-hydra.dts | 50 +++
> arch/arm/boot/dts/imx6dl-yapp4-ursa.dts | 54 +++
> 5 files changed, 759 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
> create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-draco.dts
> create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
> create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index bd40148..c0a9b89 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -445,6 +445,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6dl-wandboard.dtb \
> imx6dl-wandboard-revb1.dtb \
> imx6dl-wandboard-revd1.dtb \
> + imx6dl-yapp4-draco.dtb \
> + imx6dl-yapp4-hydra.dtb \
> + imx6dl-yapp4-ursa.dtb \
> imx6q-apalis-eval.dtb \
> imx6q-apalis-ixora.dtb \
> imx6q-apalis-ixora-v1.1.dtb \
> diff --git a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
> new file mode 100644
> index 0000000..48c2847
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
> @@ -0,0 +1,594 @@
> +// SPDX-License-Identifier: GPL-2.0
> +//
> +// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/pwm/pwm.h>
> +
> +/ {
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
> + brightness-levels = <0 32 64 128 255>;
> + default-brightness-level = <32>;
> + num-interpolated-steps = <8>;
> + power-supply = <&sw2_reg>;
> + status = "disabled";
> + };
> +
> + lcd_display: display {
> + compatible = "fsl,imx-parallel-display";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interface-pix-fmt = "rgb24";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ipu1>;
> + status = "disabled";
> +
> + port@0 {
> + reg = <0>;
> +
> + lcd_display_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + lcd_display_out: endpoint {
> + remote-endpoint = <&lcd_panel_in>;
> + };
> + };
> + };
> +
> + panel: panel {
> + compatible = "dataimage,scf0700c48ggu18";
> + power-supply = <&sw2_reg>;
> + status = "disabled";
> +
> + port {
> + lcd_panel_in: endpoint {
> + remote-endpoint = <&lcd_display_out>;
> + };
> + };
> + };
> +
> + reg_usb_h1_vbus: reg-usb-h1-vbus {
Please spell out regulator in node name, and abbr. 'reg-' for label is
all right.
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbh1_vbus>;
> + regulator-name = "usb_h1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + status = "disabled";
> + };
> +
> + reg_usb_otg_vbus: reg-usb-otg-vbus {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg_vbus>;
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + status = "okay";
> + };
> +
> + reg_pcie: reg-pcie {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pcie_reg>;
> + regulator-name = "MPCIE_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio3 19 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + status = "disabled";
> + };
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet>;
> + phy-mode = "rgmii-id";
> + phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> + phy-reset-duration = <20>;
> + phy-supply = <&sw2_reg>;
> + phy-handle = <ðphy0>;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + phy_port2: phy@1 {
> + reg = <1>;
> + };
> +
> + phy_port3: phy@2 {
> + reg = <2>;
> + };
> +
> + switch@0 {
> + compatible = "qca,qca8334";
> + reg = <0>;
> +
> + switch_ports: ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: port@0 {
> + reg = <0>;
> + label = "cpu";
> + phy-mode = "rgmii";
> + ethernet = <&fec>;
Please have a newline between properties and child node.
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> + label = "eth2";
> + phy-handle = <&phy_port2>;
> + };
> +
> + port@3 {
> + reg = <3>;
> + label = "eth1";
> + phy-handle = <&phy_port3>;
> + };
> + };
> + };
> + };
> +};
> +
> +&hdmi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hdmi_cec>;
> + ddc-i2c-bus = <&i2c2>;
> + status = "disabled";
> +};
> +
> +&i2c2 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +
> + eeprom@57 {
> + compatible = "atmel,24c128";
> + reg = <0x57>;
> + pagesize = <64>;
> + status = "okay";
> + };
> +
> + leds: led-controller@30 {
Please sort child nodes of i2c bus in order of unit-address.
> + compatible = "ti,lp5562";
> + reg = <0x30>;
> + clock-mode = /bits/ 8 <1>;
> + status = "disabled";
> +
> + chan0 {
> + chan-name = "R";
> + led-cur = /bits/ 8 <0x20>;
> + max-cur = /bits/ 8 <0x60>;
> + };
> +
> + chan1 {
> + chan-name = "G";
> + led-cur = /bits/ 8 <0x20>;
> + max-cur = /bits/ 8 <0x60>;
> + };
> +
> + chan2 {
> + chan-name = "B";
> + led-cur = /bits/ 8 <0x20>;
> + max-cur = /bits/ 8 <0x60>;
> + };
> +
> + chan3 {
> + chan-name = "W";
> + led-cur = /bits/ 8 <0x0>;
> + max-cur = /bits/ 8 <0x0>;
> + };
> + };
> +
> + pmic@8 {
> + compatible = "fsl,pfuze200";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pmic>;
> + reg = <0x8>;
> +
> + regulators {
> + sw1a_reg: sw1ab {
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1875000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <6250>;
> + };
> +
> + sw2_reg: sw2 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw3a_reg: sw3a {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <1975000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw3b_reg: sw3b {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <1975000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + swbst_reg: swbst {
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5150000>;
> + };
> +
> + snvs_reg: vsnvs {
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vref_reg: vrefddr {
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vgen1_reg: vgen1 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1550000>;
> + };
> +
> + vgen2_reg: vgen2 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1550000>;
> + };
> +
> + vgen3_reg: vgen3 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vgen4_reg: vgen4 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vgen5_reg: vgen5 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vgen6_reg: vgen6 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> + };
> + };
> +
> + touchscreen: touchscreen@5c {
> + compatible = "pixcir,pixcir_tangoc";
> + reg = <0x5c>;
> + pinctrl-0 = <&pinctrl_touch>;
> + interrupt-parent = <&gpio4>;
> + interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
> + attb-gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>;
> + reset-gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
> + touchscreen-size-x = <800>;
> + touchscreen-size-y = <480>;
> + status = "disabled";
> + };
> +};
> +
> +&i2c3 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + status = "disabled";
> +
> + gpio_oled: gpio@41 {
> + compatible = "nxp,pca9536";
> + gpio-controller;
> + #gpio-cells = <2>;
> + reg = <0x41>;
> + vcc-supply = <&sw2_reg>;
> + status = "disabled";
> + };
> +
> + oled: oled@3d {
Sort child nodes in unit-address.
> + compatible = "solomon,ssd1305fb-i2c";
> + reg = <0x3d>;
> + solomon,height = <64>;
> + solomon,width = <128>;
> + solomon,page-offset = <0>;
> + solomon,prechargep2 = <15>;
> + reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
> + vbat-supply = <&sw2_reg>;
> + status = "disabled";
> + };
> +};
> +
> +&iomuxc {
> + pinctrl_enet: enetgrp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b020
> + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b020
> + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b020
> + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b020
> + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b020
> + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b020
> + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b020
> + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b020
> + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b020
> + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b020
> + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b020
> + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b020
> + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b020
> + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b020
> + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b010
> + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b010
> + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b098
> + >;
> + };
> +
> + pinctrl_hdmi_cec: hdmicecgrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1b898
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b899
> + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b899
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b899
> + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b899
> + >;
> + };
> +
> + pinctrl_ipu1: ipu1grp {
> + fsl,pins = <
> + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
> + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
> + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
> + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10
> + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
> + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
> + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
> + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
> + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
> + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
> + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
> + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
> + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
> + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
> + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
> + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
> + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
> + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
> + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
> + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
> + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
> + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
> + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
> + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
> + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
> + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
> + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
> + >;
> + };
> +
> + pinctrl_pcie: pciegrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b098
> + MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x1b098
> + MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b098
> + >;
> + };
> +
> + pinctrl_pcie_reg: pciereggrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b098
> + >;
> + };
> +
> + pinctrl_pmic: pmicgrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b098
> + >;
> + };
> +
> + pinctrl_backlight_pwm: pwm1grp {
Name the label in a way consistent with node name, i.e.
pinctrl_pwm_xxx, and sort it alphabetically.
Shawn
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_9__PWM1_OUT 0x8
> + >;
> + };
> +
> + pinctrl_touch: touchgrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b098
> + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b098
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0a8
> + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0a8
> + >;
> + };
> +
> + pinctrl_usbh1: usbh1grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D30__USB_H1_OC 0x1b098
> + >;
> + };
> +
> + pinctrl_usbh1_vbus: usbh1-vbus {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x98
> + >;
> + };
> +
> + pinctrl_usbotg: usbotggrp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1b098
> + MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b098
> + >;
> + };
> +
> + pinctrl_usbotg_vbus: usbotg-vbus {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x98
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x1b018
> + MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1b018
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
> + >;
> + };
> +
> + pinctrl_usdhc4: usdhc4grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x1f069
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10069
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17069
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17069
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17069
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17069
> + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17069
> + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17069
> + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17069
> + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17069
> + >;
> + };
> +
> + pinctrl_wdog: wdoggrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_1__WDOG2_B 0x1b0b0
> + >;
> + };
> +};
> +
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&lcd_display_in>;
> +};
> +
> +&pcie {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pcie>;
> + reset-gpio = <&gpio7 12 GPIO_ACTIVE_LOW>;
> + vpcie-supply = <®_pcie>;
> + status = "disabled";
> +};
> +
> +&pwm1 {
> + #pwm-cells = <3>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_backlight_pwm>;
> + status = "disabled";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&usbh1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbh1>;
> + vbus-supply = <®_usb_h1_vbus>;
> + status = "disabled";
> +};
> +
> +&usbotg {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg>;
> + vbus-supply = <®_usb_otg_vbus>;
> + srp-disable;
> + hnp-disable;
> + adp-disable;
> + status = "okay";
> +};
> +
> +&usbphy1 {
> + fsl,tx-d-cal = <106>;
> + status = "okay";
> +};
> +
> +&usbphy2 {
> + fsl,tx-d-cal = <109>;
> + status = "disabled";
> +};
> +
> +&usdhc3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + bus-width = <4>;
> + cd-gpios = <&gpio7 8 GPIO_ACTIVE_LOW>;
> + wp-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
> + no-1-8-v;
> + keep-power-in-suspend;
> + wakeup-source;
> + vmmc-supply = <&sw2_reg>;
> + status = "disabled";
> +};
> +
> +&usdhc4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc4>;
> + bus-width = <8>;
> + non-removable;
> + no-1-8-v;
> + keep-power-in-suspend;
> + vmmc-supply = <&sw2_reg>;
> + status = "okay";
> +};
> +
> +&wdog1 {
> + status = "disabled";
> +};
> +
> +&wdog2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wdog>;
> + fsl,ext-reset-output;
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx6dl-yapp4-draco.dts b/arch/arm/boot/dts/imx6dl-yapp4-draco.dts
> new file mode 100644
> index 0000000..a38c407
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-yapp4-draco.dts
> @@ -0,0 +1,58 @@
> +// SPDX-License-Identifier: GPL-2.0
> +//
> +// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
> +
> +/dts-v1/;
> +
> +#include "imx6dl.dtsi"
> +#include "imx6dl-yapp4-common.dtsi"
> +
> +/ {
> + model = "Y Soft IOTA Draco i.MX6Solo board";
> + compatible = "ysoft,imx6dl-yapp4-draco", "fsl,imx6dl";
> +
> + memory@10000000 {
> + device_type = "memory";
> + reg = <0x10000000 0x20000000>;
> + };
> +};
> +
> +&backlight {
> + status = "okay";
> +};
> +
> +&lcd_display {
> + status = "okay";
> +};
> +
> +&leds {
> + status = "okay";
> +};
> +
> +&panel {
> + status = "okay";
> +};
> +
> +&pwm1 {
> + status = "okay";
> +};
> +
> +®_usb_h1_vbus {
> + status = "okay";
> +};
> +
> +&touchscreen {
> + status = "okay";
> +};
> +
> +&usbh1 {
> + status = "okay";
> +};
> +
> +&usbphy2 {
> + status = "okay";
> +};
> +
> +&usdhc3 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx6dl-yapp4-hydra.dts b/arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
> new file mode 100644
> index 0000000..f979270
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
> @@ -0,0 +1,50 @@
> +// SPDX-License-Identifier: GPL-2.0
> +//
> +// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
> +
> +/dts-v1/;
> +
> +#include "imx6dl.dtsi"
> +#include "imx6dl-yapp4-common.dtsi"
> +
> +/ {
> + model = "Y Soft IOTA Hydra i.MX6DualLite board";
> + compatible = "ysoft,imx6dl-yapp4-hydra", "fsl,imx6dl";
> +
> + memory@10000000 {
> + device_type = "memory";
> + reg = <0x10000000 0x80000000>;
> + };
> +};
> +
> +&gpio_oled {
> + status = "okay";
> +};
> +
> +&hdmi {
> + status = "okay";
> +};
> +
> +&i2c3 {
> + status = "okay";
> +};
> +
> +&leds {
> + status = "okay";
> +};
> +
> +&oled {
> + status = "okay";
> +};
> +
> +&pcie {
> + status = "okay";
> +};
> +
> +®_pcie {
> + status = "okay";
> +};
> +
> +&usdhc3 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx6dl-yapp4-ursa.dts b/arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
> new file mode 100644
> index 0000000..0d594e4
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
> @@ -0,0 +1,54 @@
> +// SPDX-License-Identifier: GPL-2.0
> +//
> +// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
> +
> +/dts-v1/;
> +
> +#include "imx6dl.dtsi"
> +#include "imx6dl-yapp4-common.dtsi"
> +
> +/ {
> + model = "Y Soft IOTA Ursa i.MX6Solo board";
> + compatible = "ysoft,imx6dl-yapp4-ursa", "fsl,imx6dl";
> +
> + memory@10000000 {
> + device_type = "memory";
> + reg = <0x10000000 0x20000000>;
> + };
> +};
> +
> +&backlight {
> + status = "okay";
> +};
> +
> +&lcd_display {
> + status = "okay";
> +};
> +
> +&panel {
> + status = "okay";
> +};
> +
> +&pwm1 {
> + status = "okay";
> +};
> +
> +®_usb_h1_vbus {
> + status = "okay";
> +};
> +
> +&switch_ports {
> + /delete-node/ port@2;
> +};
> +
> +&touchscreen {
> + status = "okay";
> +};
> +
> +&usbh1 {
> + status = "okay";
> +};
> +
> +&usbphy2 {
> + status = "okay";
> +};
> --
> 2.1.4
>
> _______________________________________________
> linux-arm-kernel mailing list
> [email protected]
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
On 13. 01. 19 10:34, Shawn Guo wrote:
> On Thu, Jan 10, 2019 at 04:20:51PM +0000, Vokáč Michal wrote:
>> These are i.MX6S/DL based SBCs embedded in various Y Soft products.
>> All share the same board design but have slightly different HW
>> configuration.
>>
>> Ursa
>> - i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
>> - parallel WVGA 7" LCD with touch panel
>> - 1x Eth (QCA8334 switch)
>> - USB OTG
>> - USB host (micro-B)
>>
>> Draco
>> - i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
>> - parallel WVGA 7" LCD with touch panel
>> - 2x Eth (QCA8334 switch)
>> - USB OTG
>> - USB host (micro-B)
>> - RGB LED (I2C LP5562)
>> - 3.5mm audio jack + codec (LM49350)
>>
>> Hydra
>> - i.MX6DL SoC, 2GB RAM DDR3, 4GB eMMC, microSD
>> - I2C OLED display, capacitive matrix keys
>> - 2x Eth (QCA8334 switch)
>> - USB OTG
>> - RGB LED (I2C LP5562)
>> - 3.5mm audio jack + codec (LM49350)
>> - HDMI
>> - miniPCIe slot
>>
>> Cc: Andrew Lunn <[email protected]>
>> Signed-off-by: Michal Vokáč <[email protected]>
>> ---
>> Changes since v2:
>> - Remove cpus {/delete-node/ cpu@1;}; node from i.MX6Solo based board. (Fabio)
>> - Use "device_type = "memory";" in memory nodes. (Fabio)
>> - Use GPIO_ACTIVE_LOW for fec phy-reset-gpios. (Fabio)
>> - Use "-" in node names. (Rob)
>> - Remove label from led-controller node. (Rob)
>>
>> Changes since v1:
>> - Enable HDMI on Hydra board.
>> - Move regulators to the root node and remove simple-bus property. (Rob)
>> - Remove reg and unit-address property from regulators. (Rob)
>> - Use correct names for led-controller and pmic node. (Rob)
>> - Use wakeup-source instead of deprecated enable-sdio-wakeup. (Shawn)
>>
>> arch/arm/boot/dts/Makefile | 3 +
>> arch/arm/boot/dts/imx6dl-yapp4-common.dtsi | 594 +++++++++++++++++++++++++++++
>> arch/arm/boot/dts/imx6dl-yapp4-draco.dts | 58 +++
>> arch/arm/boot/dts/imx6dl-yapp4-hydra.dts | 50 +++
>> arch/arm/boot/dts/imx6dl-yapp4-ursa.dts | 54 +++
>> 5 files changed, 759 insertions(+)
>> create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
>> create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-draco.dts
>> create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
>> create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index bd40148..c0a9b89 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -445,6 +445,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
>> imx6dl-wandboard.dtb \
>> imx6dl-wandboard-revb1.dtb \
>> imx6dl-wandboard-revd1.dtb \
>> + imx6dl-yapp4-draco.dtb \
>> + imx6dl-yapp4-hydra.dtb \
>> + imx6dl-yapp4-ursa.dtb \
>> imx6q-apalis-eval.dtb \
>> imx6q-apalis-ixora.dtb \
>> imx6q-apalis-ixora-v1.1.dtb \
>> diff --git a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
>> new file mode 100644
>> index 0000000..48c2847
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
>> @@ -0,0 +1,594 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +//
>> +// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
>> +
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/interrupt-controller/irq.h>
>> +#include <dt-bindings/pwm/pwm.h>
>> +
>> +/ {
>> + backlight: backlight {
>> + compatible = "pwm-backlight";
>> + pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
>> + brightness-levels = <0 32 64 128 255>;
>> + default-brightness-level = <32>;
>> + num-interpolated-steps = <8>;
>> + power-supply = <&sw2_reg>;
>> + status = "disabled";
>> + };
>> +
>> + lcd_display: display {
>> + compatible = "fsl,imx-parallel-display";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interface-pix-fmt = "rgb24";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_ipu1>;
>> + status = "disabled";
>> +
>> + port@0 {
>> + reg = <0>;
>> +
>> + lcd_display_in: endpoint {
>> + remote-endpoint = <&ipu1_di0_disp0>;
>> + };
>> + };
>> +
>> + port@1 {
>> + reg = <1>;
>> +
>> + lcd_display_out: endpoint {
>> + remote-endpoint = <&lcd_panel_in>;
>> + };
>> + };
>> + };
>> +
>> + panel: panel {
>> + compatible = "dataimage,scf0700c48ggu18";
>> + power-supply = <&sw2_reg>;
>> + status = "disabled";
>> +
>> + port {
>> + lcd_panel_in: endpoint {
>> + remote-endpoint = <&lcd_display_out>;
>> + };
>> + };
>> + };
>> +
>> + reg_usb_h1_vbus: reg-usb-h1-vbus {
>
> Please spell out regulator in node name, and abbr. 'reg-' for label is
> all right.
>
>> + compatible = "regulator-fixed";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usbh1_vbus>;
>> + regulator-name = "usb_h1_vbus";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
>> + enable-active-high;
>> + status = "disabled";
>> + };
>> +
>> + reg_usb_otg_vbus: reg-usb-otg-vbus {
>> + compatible = "regulator-fixed";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usbotg_vbus>;
>> + regulator-name = "usb_otg_vbus";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
>> + enable-active-high;
>> + status = "okay";
>> + };
>> +
>> + reg_pcie: reg-pcie {
>> + compatible = "regulator-fixed";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_pcie_reg>;
>> + regulator-name = "MPCIE_3V3";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + gpio = <&gpio3 19 GPIO_ACTIVE_HIGH>;
>> + enable-active-high;
>> + status = "disabled";
>> + };
>> +};
>> +
>> +&fec {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_enet>;
>> + phy-mode = "rgmii-id";
>> + phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
>> + phy-reset-duration = <20>;
>> + phy-supply = <&sw2_reg>;
>> + phy-handle = <ðphy0>;
>> + status = "okay";
>> +
>> + mdio {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + phy_port2: phy@1 {
>> + reg = <1>;
>> + };
>> +
>> + phy_port3: phy@2 {
>> + reg = <2>;
>> + };
>> +
>> + switch@0 {
>> + compatible = "qca,qca8334";
>> + reg = <0>;
>> +
>> + switch_ports: ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + ethphy0: port@0 {
>> + reg = <0>;
>> + label = "cpu";
>> + phy-mode = "rgmii";
>> + ethernet = <&fec>;
>
> Please have a newline between properties and child node.
>
>> + fixed-link {
>> + speed = <1000>;
>> + full-duplex;
>> + };
>> + };
>> +
>> + port@2 {
>> + reg = <2>;
>> + label = "eth2";
>> + phy-handle = <&phy_port2>;
>> + };
>> +
>> + port@3 {
>> + reg = <3>;
>> + label = "eth1";
>> + phy-handle = <&phy_port3>;
>> + };
>> + };
>> + };
>> + };
>> +};
>> +
>> +&hdmi {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_hdmi_cec>;
>> + ddc-i2c-bus = <&i2c2>;
>> + status = "disabled";
>> +};
>> +
>> +&i2c2 {
>> + clock-frequency = <100000>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_i2c2>;
>> + status = "okay";
>> +
>> + eeprom@57 {
>> + compatible = "atmel,24c128";
>> + reg = <0x57>;
>> + pagesize = <64>;
>> + status = "okay";
>> + };
>> +
>> + leds: led-controller@30 {
>
> Please sort child nodes of i2c bus in order of unit-address.
>
>> + compatible = "ti,lp5562";
>> + reg = <0x30>;
>> + clock-mode = /bits/ 8 <1>;
>> + status = "disabled";
>> +
>> + chan0 {
>> + chan-name = "R";
>> + led-cur = /bits/ 8 <0x20>;
>> + max-cur = /bits/ 8 <0x60>;
>> + };
>> +
>> + chan1 {
>> + chan-name = "G";
>> + led-cur = /bits/ 8 <0x20>;
>> + max-cur = /bits/ 8 <0x60>;
>> + };
>> +
>> + chan2 {
>> + chan-name = "B";
>> + led-cur = /bits/ 8 <0x20>;
>> + max-cur = /bits/ 8 <0x60>;
>> + };
>> +
>> + chan3 {
>> + chan-name = "W";
>> + led-cur = /bits/ 8 <0x0>;
>> + max-cur = /bits/ 8 <0x0>;
>> + };
>> + };
>> +
>> + pmic@8 {
>> + compatible = "fsl,pfuze200";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_pmic>;
>> + reg = <0x8>;
>> +
>> + regulators {
>> + sw1a_reg: sw1ab {
>> + regulator-min-microvolt = <300000>;
>> + regulator-max-microvolt = <1875000>;
>> + regulator-boot-on;
>> + regulator-always-on;
>> + regulator-ramp-delay = <6250>;
>> + };
>> +
>> + sw2_reg: sw2 {
>> + regulator-min-microvolt = <800000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> + regulator-always-on;
>> + };
>> +
>> + sw3a_reg: sw3a {
>> + regulator-min-microvolt = <400000>;
>> + regulator-max-microvolt = <1975000>;
>> + regulator-boot-on;
>> + regulator-always-on;
>> + };
>> +
>> + sw3b_reg: sw3b {
>> + regulator-min-microvolt = <400000>;
>> + regulator-max-microvolt = <1975000>;
>> + regulator-boot-on;
>> + regulator-always-on;
>> + };
>> +
>> + swbst_reg: swbst {
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5150000>;
>> + };
>> +
>> + snvs_reg: vsnvs {
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <3000000>;
>> + regulator-boot-on;
>> + regulator-always-on;
>> + };
>> +
>> + vref_reg: vrefddr {
>> + regulator-boot-on;
>> + regulator-always-on;
>> + };
>> +
>> + vgen1_reg: vgen1 {
>> + regulator-min-microvolt = <800000>;
>> + regulator-max-microvolt = <1550000>;
>> + };
>> +
>> + vgen2_reg: vgen2 {
>> + regulator-min-microvolt = <800000>;
>> + regulator-max-microvolt = <1550000>;
>> + };
>> +
>> + vgen3_reg: vgen3 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-always-on;
>> + };
>> +
>> + vgen4_reg: vgen4 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-always-on;
>> + };
>> +
>> + vgen5_reg: vgen5 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-always-on;
>> + };
>> +
>> + vgen6_reg: vgen6 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-always-on;
>> + };
>> + };
>> + };
>> +
>> + touchscreen: touchscreen@5c {
>> + compatible = "pixcir,pixcir_tangoc";
>> + reg = <0x5c>;
>> + pinctrl-0 = <&pinctrl_touch>;
>> + interrupt-parent = <&gpio4>;
>> + interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
>> + attb-gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>;
>> + reset-gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
>> + touchscreen-size-x = <800>;
>> + touchscreen-size-y = <480>;
>> + status = "disabled";
>> + };
>> +};
>> +
>> +&i2c3 {
>> + clock-frequency = <100000>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_i2c3>;
>> + status = "disabled";
>> +
>> + gpio_oled: gpio@41 {
>> + compatible = "nxp,pca9536";
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> + reg = <0x41>;
>> + vcc-supply = <&sw2_reg>;
>> + status = "disabled";
>> + };
>> +
>> + oled: oled@3d {
>
> Sort child nodes in unit-address.
>
>> + compatible = "solomon,ssd1305fb-i2c";
>> + reg = <0x3d>;
>> + solomon,height = <64>;
>> + solomon,width = <128>;
>> + solomon,page-offset = <0>;
>> + solomon,prechargep2 = <15>;
>> + reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
>> + vbat-supply = <&sw2_reg>;
>> + status = "disabled";
>> + };
>> +};
>> +
>> +&iomuxc {
>> + pinctrl_enet: enetgrp {
>> + fsl,pins = <
>> + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b020
>> + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b020
>> + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b020
>> + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b020
>> + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b020
>> + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b020
>> + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b020
>> + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b020
>> + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b020
>> + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b020
>> + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b020
>> + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b020
>> + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b020
>> + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b020
>> + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b010
>> + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b010
>> + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b098
>> + >;
>> + };
>> +
>> + pinctrl_hdmi_cec: hdmicecgrp {
>> + fsl,pins = <
>> + MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1b898
>> + >;
>> + };
>> +
>> + pinctrl_i2c2: i2c2grp {
>> + fsl,pins = <
>> + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b899
>> + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b899
>> + >;
>> + };
>> +
>> + pinctrl_i2c3: i2c3grp {
>> + fsl,pins = <
>> + MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b899
>> + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b899
>> + >;
>> + };
>> +
>> + pinctrl_ipu1: ipu1grp {
>> + fsl,pins = <
>> + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
>> + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
>> + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
>> + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10
>> + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
>> + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
>> + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
>> + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
>> + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
>> + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
>> + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
>> + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
>> + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
>> + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
>> + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
>> + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
>> + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
>> + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
>> + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
>> + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
>> + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
>> + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
>> + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
>> + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
>> + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
>> + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
>> + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
>> + >;
>> + };
>> +
>> + pinctrl_pcie: pciegrp {
>> + fsl,pins = <
>> + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b098
>> + MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x1b098
>> + MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b098
>> + >;
>> + };
>> +
>> + pinctrl_pcie_reg: pciereggrp {
>> + fsl,pins = <
>> + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b098
>> + >;
>> + };
>> +
>> + pinctrl_pmic: pmicgrp {
>> + fsl,pins = <
>> + MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b098
>> + >;
>> + };
>> +
>> + pinctrl_backlight_pwm: pwm1grp {
>
> Name the label in a way consistent with node name, i.e.
> pinctrl_pwm_xxx, and sort it alphabetically.
Thank you Shawn. I will fix all the issues.
I am amazed how you, reviewers/maintainers, can always find something to improve!
Michal