2007-12-14 09:11:10

by Arun Thomas

Subject: PROBLEM: E6850 has an 8+ minute delay during boot

Hi,

My Dell Vostro desktop w/ an Intel E6850 dual-core 3GHz CPU has an 8+
minute delay during boot. The machine seems to run fine after it
boots. The problem occurs on the Ubuntu gutsy 2.6.22-14 kernel,
2.6.23.9, and 2.6.24-rc5. I have upgraded to the most recent Dell BIOS
version (1.0.8). I am running an SMP kernel currently, but the problem
presents itself in uniprocessor mode (nosmp) also. I'm running the
machine in 32-bit mode w/hyperthreading configured.

Here are a few interesting things in the dmesg output for the
2.6.24-rc5 kernel (smp). The full dmesg is also included farther down.

[ 20.101501] CPU: After generic identify, caps: bfebfbff 20100000
00000000 00000000 0000e3fd 00000000 00000001 00000000
[ 20.101505] monitor/mwait feature present.
[ 20.101506] using mwait in idle threads.
[ 20.101508] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 20.101509] CPU: L2 cache: 4096K
[ 20.101511] CPU: Physical Processor ID: 0
[ 20.101511] CPU: Processor Core ID: 0
[ 20.101513] CPU: After all inits, caps: bfebfbff 20100000 00000000
00003940 0000e3fd 00000000 00000001 00000000
[ 20.101517] Compat vDSO mapped to ffffe000.
[ 20.101525] Checking 'hlt' instruction... OK.
[ 20.117651] SMP alternatives: switching to UP code
[ 20.118574] ACPI: Core revision 20070126
[ 20.175154] CPU0: Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz stepping 0b
[ 20.175163] SMP alternatives: switching to SMP code
[ 20.175437] Booting processor 1/1 eip 3000
[ 20.185881] Initializing CPU#1
[ 527.926587] Calibrating delay using timer specific routine..
200566.59 BogoMIPS (lpj=401133185)
[ 527.926592] CPU: After generic identify, caps: bfebfbff 20100000
00000000 00000000 0000e3fd 00000000 00000001 00000000
[ 527.926595] monitor/mwait feature present.
[ 527.926596] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 527.926597] CPU: L2 cache: 4096K
[ 527.926599] CPU: Physical Processor ID: 0
[ 527.926599] CPU: Processor Core ID: 1
[ 527.926600] CPU: After all inits, caps: bfebfbff 20100000 00000000
00003940 0000e3fd 00000000 00000001 00000000
[ 527.927141] CPU1: Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz stepping 0b
[ 527.927154] Total of 2 processors activated (206555.60 BogoMIPS).
...
[ 528.095491] Setting up standard PCI resources
[ 528.096557] mtrr: your CPUs had inconsistent fixed MTRR settings
[ 528.096558] mtrr: probably your BIOS does not setup all CPUs.
[ 528.096559] mtrr: corrected configuration.


Here's a snip from the dmesg of the same kernel in uniprocessor mode
(nosmp). Full dmesg also included farther down.

[ 31.670391] TCP reno registered
[ 31.681591] checking if image is initramfs...<7>Switched to high
resolution mode on CPU 0
[ 540.133678] Clocksource tsc unstable (delta = 299978139535 ns)
[ 540.137708] Time: hpet clocksource has been installed.
[ 540.432798] it is


Here's my /proc/cpuinfo:

processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 15
model name : Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz
stepping : 11
cpu MHz : 2992.539
cache size : 4096 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 2
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 10
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx
lm constant_tsc arch_perfmon pebs bts pni monitor ds_cpl vmx smx est
tm2 ssse3 cx16 xtpr lahf_lm
bogomips : 5988.99
clflush size : 64

processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 15
model name : Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz
stepping : 11
cpu MHz : 2992.539
cache size : 4096 KB
physical id : 0
siblings : 2
core id : 1
cpu cores : 2
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 10
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx
lm constant_tsc arch_perfmon pebs bts pni monitor ds_cpl vmx smx est
tm2 ssse3 cx16 xtpr lahf_lm
bogomips : 5984.97
clflush size : 64

Below is a lot of info. Some info is extraneous, but I'm guessing more
is better in this case. I have included the full dmesg output, my full
config (based on the Ubuntu gutsy config), and all the info mentioned
in REPORTING-BUGS. Please let me know if there's any other info that
would be helpful.

Thanks,
Arun


=========
Full smp dmesg:

[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 2.6.24-rc5-custom (root@machine) (gcc
version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP
Wed Dec 12 23:18:52 EST 2007
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 0000000000099c00 (usable)
[ 0.000000] BIOS-e820: 0000000000099c00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fe90000 (usable)
[ 0.000000] BIOS-e820: 000000007fe90000 - 000000007fee3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007fee3000 - 000000007fef0000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007fef0000 - 000000007ff00000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] 1150MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f3f00
[ 0.000000] Entering add_active_range(0, 0, 523920) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 523920
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 523920
[ 0.000000] On node 0 totalpages: 523920
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2301 pages used for memmap
[ 0.000000] HighMem zone: 292243 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.5 present.
[ 0.000000] ACPI: RSDP 000F97A0, 0024 (r2 DELL )
[ 0.000000] ACPI: XSDT 7FEE3080, 005C (r1 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: FACP 7FEE7200, 00F4 (r3 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: DSDT 7FEE3200, 3FFC (r1 DELL AWRDACPI 1000
MSFT 3000000)
[ 0.000000] ACPI: FACS 7FE90000, 0040
[ 0.000000] ACPI: HPET 7FEE73C0, 0038 (r1 DELL FX09 42302E31
AWRD 98)
[ 0.000000] ACPI: MCFG 7FEE7400, 003C (r1 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: SLIC 7FEE7440, 0176 (r1 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: DMY2 7FEE75C0, 0080 (r1 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: APIC 7FEE7300, 0084 (r1 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: SSDT 7FEE7CA0, 0380 (r1 PmRef CpuPm 3000
INTL 20041203)
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:15 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 6:15 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 80000000 (gap:
7ff00000:60100000)
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 519827
[ 0.000000] Kernel command line:
root=UUID=8420f2d5-9569-476d-b3fc-6365a9987426 ro quiet splash
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 2992.539 MHz processor.
[ 19.961593] Console: colour VGA+ 80x25
[ 19.961595] console [tty0] enabled
[ 19.961731] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 19.961888] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 20.021313] Memory: 2028720k/2095680k available (2069k kernel code,
65644k reserved, 958k data, 360k init, 1178176k highmem)
[ 20.021317] virtual kernel memory layout:
[ 20.021318] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 20.021319] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 20.021319] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 20.021320] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 20.021320] .init : 0xc03fb000 - 0xc0455000 ( 360 kB)
[ 20.021321] .data : 0xc0305408 - 0xc03f4d84 ( 958 kB)
[ 20.021321] .text : 0xc0100000 - 0xc0305408 (2069 kB)
[ 20.021323] Checking if this processor honours the WP bit even in
supervisor mode... Ok.
[ 20.021348] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4,
CPUs=2, Nodes=1
[ 20.021433] hpet clockevent registered
[ 20.101392] Calibrating delay using timer specific routine..
5989.01 BogoMIPS (lpj=11978034)
[ 20.101407] Security Framework initialized
[ 20.101410] SELinux: Disabled at boot.
[ 20.101412] Capability LSM initialized
[ 20.101419] Mount-cache hash table entries: 512
[ 20.101494] Initializing cgroup subsys cpuacct
[ 20.101501] CPU: After generic identify, caps: bfebfbff 20100000
00000000 00000000 0000e3fd 00000000 00000001 00000000
[ 20.101505] monitor/mwait feature present.
[ 20.101506] using mwait in idle threads.
[ 20.101508] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 20.101509] CPU: L2 cache: 4096K
[ 20.101511] CPU: Physical Processor ID: 0
[ 20.101511] CPU: Processor Core ID: 0
[ 20.101513] CPU: After all inits, caps: bfebfbff 20100000 00000000
00003940 0000e3fd 00000000 00000001 00000000
[ 20.101517] Compat vDSO mapped to ffffe000.
[ 20.101525] Checking 'hlt' instruction... OK.
[ 20.117651] SMP alternatives: switching to UP code
[ 20.118574] ACPI: Core revision 20070126
[ 20.175154] CPU0: Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz stepping 0b
[ 20.175163] SMP alternatives: switching to SMP code
[ 20.175437] Booting processor 1/1 eip 3000
[ 20.185881] Initializing CPU#1
[ 527.926587] Calibrating delay using timer specific routine..
200566.59 BogoMIPS (lpj=401133185)
[ 527.926592] CPU: After generic identify, caps: bfebfbff 20100000
00000000 00000000 0000e3fd 00000000 00000001 00000000
[ 527.926595] monitor/mwait feature present.
[ 527.926596] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 527.926597] CPU: L2 cache: 4096K
[ 527.926599] CPU: Physical Processor ID: 0
[ 527.926599] CPU: Processor Core ID: 1
[ 527.926600] CPU: After all inits, caps: bfebfbff 20100000 00000000
00003940 0000e3fd 00000000 00000001 00000000
[ 527.927141] CPU1: Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz stepping 0b
[ 527.927154] Total of 2 processors activated (206555.60 BogoMIPS).
[ 527.927289] ENABLING IO-APIC IRQs
[ 527.927444] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 528.074569] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 528.094566] Brought up 2 CPUs
[ 528.094582] CPU0 attaching sched-domain:
[ 528.094584] domain 0: span 03
[ 528.094585] groups: 01 02
[ 528.094586] CPU1 attaching sched-domain:
[ 528.094587] domain 0: span 03
[ 528.094588] groups: 02 01
[ 528.094711] net_namespace: 64 bytes
[ 528.094716] Booting paravirtualized kernel on bare hardware
[ 528.094972] Time: 0:36:23 Date: 12/13/07
[ 528.095000] NET: Registered protocol family 16
[ 528.095095] EISA bus registered
[ 528.095098] ACPI: bus type pci registered
[ 528.095172] PCI: Using MMCONFIG
[ 528.095491] Setting up standard PCI resources
[ 528.096557] mtrr: your CPUs had inconsistent fixed MTRR settings
[ 528.096558] mtrr: probably your BIOS does not setup all CPUs.
[ 528.096559] mtrr: corrected configuration.
[ 528.097279] ACPI: EC: Look up EC in DSDT
[ 528.099474] ACPI: Interpreter enabled
[ 528.099476] ACPI: (supports S0 S3 S5)
[ 528.099482] ACPI: Using IOAPIC for interrupt routing
[ 528.101844] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 528.102410] PCI: Transparent bridge - 0000:00:1e.0
[ 528.102425] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 528.102526] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 528.110728] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[ 528.110791] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11
12 14 15) *0, disabled.
[ 528.110854] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11 12 14 15)
[ 528.110915] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 528.110978] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[ 528.111039] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 528.111101] ACPI: PCI Interrupt Link [LNK0] (IRQs *3 4 5 7 9 10 11 12 14 15)
[ 528.111162] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 *4 5 7 9 10 11 12 14 15)
[ 528.111227] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 528.111243] pnp: PnP ACPI init
[ 528.111246] ACPI: bus type pnp registered
[ 528.112179] pnpacpi: exceeded the max number of mem resources: 12
[ 528.112243] pnp: PnP ACPI: found 11 devices
[ 528.112244] ACPI: ACPI bus type pnp unregistered
[ 528.112246] PnPBIOS: Disabled by ACPI PNP
[ 528.112330] PCI: Using ACPI for IRQ routing
[ 528.112331] PCI: If a device doesn't work, try "pci=routeirq". If
it helps, post a report
[ 528.130660] NET: Registered protocol family 8
[ 528.130661] NET: Registered protocol family 20
[ 528.130686] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 528.130690] hpet0: 4 64-bit timers, 14318180 Hz
[ 528.134530] Time: tsc clocksource has been installed.
[ 528.154595] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 528.154597] system 00:01: ioport range 0x800-0x87f has been reserved
[ 528.154600] system 00:01: ioport range 0x290-0x297 has been reserved
[ 528.154602] system 00:01: ioport range 0x880-0x88f has been reserved
[ 528.154608] system 00:07: ioport range 0x400-0x4bf has been reserved
[ 528.154613] system 00:09: iomem range 0xe0000000-0xefffffff could
not be reserved
[ 528.154618] system 00:0a: iomem range 0xf0000-0xfffff could not be reserved
[ 528.154620] system 00:0a: iomem range 0x7ff00000-0x7fffffff has been reserved
[ 528.154623] system 00:0a: iomem range 0xfed00000-0xfed000ff could
not be reserved
[ 528.154625] system 00:0a: iomem range 0x7fe90000-0x7fefffff could
not be reserved
[ 528.154627] system 00:0a: iomem range 0x0-0x9ffff could not be reserved
[ 528.154629] system 00:0a: iomem range 0x100000-0x7fe8ffff could not
be reserved
[ 528.154632] system 00:0a: iomem range 0xfec00000-0xfec00fff could
not be reserved
[ 528.154634] system 00:0a: iomem range 0xfed14000-0xfed1dfff could
not be reserved
[ 528.154636] system 00:0a: iomem range 0xfed20000-0xfed9ffff could
not be reserved
[ 528.154639] system 00:0a: iomem range 0xfee00000-0xfee00fff could
not be reserved
[ 528.154641] system 00:0a: iomem range 0xffb00000-0xffb7ffff could
not be reserved
[ 528.154643] system 00:0a: iomem range 0xfff00000-0xffffffff could
not be reserved
[ 528.184881] PCI: Bridge: 0000:00:01.0
[ 528.184883] IO window: d000-dfff
[ 528.184884] MEM window: f8000000-fbffffff
[ 528.184885] PREFETCH window: d0000000-dfffffff
[ 528.184886] PCI: Bridge: 0000:00:1e.0
[ 528.184888] IO window: c000-cfff
[ 528.184890] MEM window: fdd00000-fddfffff
[ 528.184892] PREFETCH window: fde00000-fdefffff
[ 528.184898] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level,
low) -> IRQ 16
[ 528.184900] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 528.184905] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 528.184910] NET: Registered protocol family 2
[ 528.226685] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 528.226846] TCP established hash table entries: 131072 (order: 8,
1048576 bytes)
[ 528.227093] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 528.227210] TCP: Hash tables configured (established 131072 bind 65536)
[ 528.227211] TCP reno registered
[ 528.238762] checking if image is initramfs...<7>Switched to high
resolution mode on CPU 1
[ 528.362604] Switched to high resolution mode on CPU 0
[ 529.319857] it is
[ 530.462587] Freeing initrd memory: 44428k freed
[ 530.462986] audit: initializing netlink socket (disabled)
[ 530.462995] audit(1197505676.604:1): initialized
[ 530.463128] highmem bounce pool size: 64 pages
[ 530.464106] VFS: Disk quotas dquot_6.5.1
[ 530.464144] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 530.464212] io scheduler noop registered
[ 530.464213] io scheduler anticipatory registered
[ 530.464215] io scheduler deadline registered
[ 530.464220] io scheduler cfq registered (default)
[ 530.464318] Boot video device is 0000:01:00.0
[ 530.464366] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 530.464376] assign_interrupt_mode Found MSI capability
[ 530.464386] Allocate Port Service[0000:00:01.0:pcie00]
[ 530.464403] Allocate Port Service[0000:00:01.0:pcie03]
[ 530.464513] isapnp: Scanning for PnP cards...
[ 530.817359] isapnp: No Plug & Play device found
[ 530.827675] Real Time Clock Driver v1.12ac
[ 530.827774] hpet_resources: 0xfed00000 is busy
[ 530.827796] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports,
IRQ sharing enabled
[ 530.828393] RAMDISK driver initialized: 16 RAM disks of 65536K size
1024 blocksize
[ 530.828426] input: Macintosh mouse button emulation as /class/input/input0
[ 530.828493] PNP: No PS/2 controller found. Probing ports directly.
[ 530.828758] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 530.828761] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 530.844999] mice: PS/2 mouse device common for all mice
[ 530.845077] EISA: Probing bus 0 at eisa.0
[ 530.845101] EISA: Detected 0 cards.
[ 530.845161] TCP cubic registered
[ 530.845166] NET: Registered protocol family 1
[ 530.845181] Using IPI No-Shortcut mode
[ 530.845245] Magic number: 3:590:607
[ 530.845260] hash matches device ptyae
[ 530.845378] Freeing unused kernel memory: 360k freed
[ 531.962339] fuse init (API version 7.9)
[ 531.965010] ACPI: Fan [FAN] (on)
[ 531.967955] ACPI: SSDT 7FEE7680, 022A (r1 PmRef Cpu0Ist 3000
INTL 20040311)
[ 531.968101] ACPI: SSDT 7FEE7B40, 0152 (r1 PmRef Cpu1Ist 3000
INTL 20040311)
[ 531.968171] ACPI Exception (processor_core-0816): AE_NOT_FOUND,
Processor Device is not present [20070126]
[ 531.968177] ACPI Exception (processor_core-0816): AE_NOT_FOUND,
Processor Device is not present [20070126]
[ 531.968996] ACPI: Thermal Zone [THRM] (40 C)
[ 532.213666] usbcore: registered new interface driver usbfs
[ 532.213683] usbcore: registered new interface driver hub
[ 532.225521] usbcore: registered new device driver usb
[ 532.226341] USB Universal Host Controller Interface driver v3.0
[ 532.226376] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level,
low) -> IRQ 16
[ 532.226384] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 532.226386] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 532.226549] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned
bus number 1
[ 532.226572] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000fe00
[ 532.226658] usb usb1: configuration #1 chosen from 1 choice
[ 532.226672] hub 1-0:1.0: USB hub found
[ 532.226674] hub 1-0:1.0: 2 ports detected
[ 532.289186] SCSI subsystem initialized
[ 532.298890] libata version 3.00 loaded.
[ 532.332118] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level,
low) -> IRQ 17
[ 532.332125] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 532.332128] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 532.332141] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned
bus number 2
[ 532.332162] uhci_hcd 0000:00:1a.1: irq 17, io base 0x0000fd00
[ 532.332221] usb usb2: configuration #1 chosen from 1 choice
[ 532.332234] hub 2-0:1.0: USB hub found
[ 532.332236] hub 2-0:1.0: 2 ports detected
[ 532.432076] ACPI: PCI Interrupt 0000:00:1a.2[D] -> GSI 19 (level,
low) -> IRQ 18
[ 532.432082] PCI: Setting latency timer of device 0000:00:1a.2 to 64
[ 532.432084] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 532.432101] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned
bus number 3
[ 532.432122] uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000fc00
[ 532.432201] usb usb3: configuration #1 chosen from 1 choice
[ 532.432223] hub 3-0:1.0: USB hub found
[ 532.432225] hub 3-0:1.0: 2 ports detected
[ 532.536006] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level,
low) -> IRQ 19
[ 532.536012] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 532.536014] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 532.536030] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned
bus number 4
[ 532.536051] uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000fb00
[ 532.536132] usb usb4: configuration #1 chosen from 1 choice
[ 532.536156] hub 4-0:1.0: USB hub found
[ 532.536158] hub 4-0:1.0: 2 ports detected
[ 532.639942] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level,
low) -> IRQ 18
[ 532.639947] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 532.639950] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 532.639967] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned
bus number 5
[ 532.639985] uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000fa00
[ 532.640065] usb usb5: configuration #1 chosen from 1 choice
[ 532.640084] hub 5-0:1.0: USB hub found
[ 532.640092] hub 5-0:1.0: 2 ports detected
[ 532.671864] usb 2-2: new full speed USB device using uhci_hcd and address 2
[ 532.743882] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level,
low) -> IRQ 20
[ 532.743887] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 532.743890] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 532.743908] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned
bus number 6
[ 532.743929] uhci_hcd 0000:00:1d.2: irq 20, io base 0x0000f900
[ 532.744011] usb usb6: configuration #1 chosen from 1 choice
[ 532.744033] hub 6-0:1.0: USB hub found
[ 532.744035] hub 6-0:1.0: 2 ports detected
[ 532.814977] usb 2-2: configuration #1 chosen from 1 choice
[ 532.817932] hub 2-2:1.0: USB hub found
[ 532.819915] hub 2-2:1.0: 2 ports detected
[ 532.848250] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level,
low) -> IRQ 20
[ 532.848256] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 532.848258] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 532.848271] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned
bus number 7
[ 532.852155] PCI: cache line size of 32 is not supported by device
0000:00:1a.7
[ 532.852158] ehci_hcd 0000:00:1a.7: irq 20, io mem 0xfdffe000
[ 532.867742] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00,
driver 10 Dec 2004
[ 532.867805] usb usb7: configuration #1 chosen from 1 choice
[ 532.867820] hub 7-0:1.0: USB hub found
[ 532.867823] hub 7-0:1.0: 6 ports detected
[ 532.927761] usb 2-2: USB disconnect, address 2
[ 532.971744] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level,
low) -> IRQ 19
[ 532.971753] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 532.971756] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 532.971775] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned
bus number 8
[ 532.975683] PCI: cache line size of 32 is not supported by device
0000:00:1d.7
[ 532.975687] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xfdffd000
[ 532.987663] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00,
driver 10 Dec 2004
[ 532.987735] usb usb8: configuration #1 chosen from 1 choice
[ 532.987754] hub 8-0:1.0: USB hub found
[ 532.987757] hub 8-0:1.0: 6 ports detected
[ 533.091797] ahci 0000:00:1f.2: version 3.0
[ 533.091814] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 19 (level,
low) -> IRQ 18
[ 533.295492] usb 7-4: new high speed USB device using ehci_hcd and address 2
[ 533.427804] usb 7-4: configuration #1 chosen from 1 choice
[ 533.427884] hub 7-4:1.0: USB hub found
[ 533.427989] hub 7-4:1.0: 2 ports detected
[ 533.731325] usb 7-4.1: new high speed USB device using ehci_hcd and address 3
[ 533.827581] usb 7-4.1: configuration #1 chosen from 1 choice
[ 533.827660] hub 7-4.1:1.0: USB hub found
[ 533.827769] hub 7-4.1:1.0: 4 ports detected
[ 534.095023] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3
Gbps 0x3f impl RAID mode
[ 534.095026] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pmp
pio slum part
[ 534.095030] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 534.095244] scsi0 : ahci
[ 534.095328] scsi1 : ahci
[ 534.095391] scsi2 : ahci
[ 534.095453] scsi3 : ahci
[ 534.095515] scsi4 : ahci
[ 534.095575] scsi5 : ahci
[ 534.095631] ata1: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc100 irq 222
[ 534.095633] ata2: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc180 irq 222
[ 534.095635] ata3: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc200 irq 222
[ 534.095637] ata4: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc280 irq 222
[ 534.095638] ata5: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc300 irq 222
[ 534.095640] ata6: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc380 irq 222
[ 534.131105] usb 7-4.1.1: new high speed USB device using ehci_hcd
and address 4
[ 534.310946] usb 7-4.1.1: configuration #1 chosen from 1 choice
[ 534.510895] usb 7-4.1.3: new low speed USB device using ehci_hcd
and address 5
[ 534.606278] usb 7-4.1.3: configuration #1 chosen from 1 choice
[ 534.806732] usb 7-4.1.4: new low speed USB device using ehci_hcd
and address 6
[ 534.929230] usb 7-4.1.4: configuration #1 chosen from 1 choice
[ 534.937712] usbcore: registered new interface driver libusual
[ 534.937758] usbcore: registered new interface driver hiddev
[ 534.939408] input: USB Optical Mouse as /class/input/input1
[ 534.941440] Initializing USB Mass Storage driver...
[ 534.941863] scsi6 : SCSI emulation for USB Mass Storage devices
[ 534.942197] usb-storage: device found at 4
[ 534.942198] usb-storage: waiting for device to settle before scanning
[ 534.966541] input: USB HID v1.11 Mouse [USB Optical Mouse] on
usb-0000:00:1a.7-4.1.3
[ 534.974316] input: Dell Dell USB Keyboard as /class/input/input2
[ 534.995489] input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard]
on usb-0000:00:1a.7-4.1.4
[ 534.995501] usbcore: registered new interface driver usbhid
[ 534.995503] usbcore: registered new interface driver usb-storage
[ 534.995505] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 534.995509] USB Mass Storage support registered.
[ 535.742028] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 535.759000] ata1.00: ATA-8: SAMSUNG HD321KJ, CP100-12, max UDMA7
[ 535.759002] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 535.761044] ata1.00: configured for UDMA/133
[ 537.405035] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 537.562660] ata2.00: ATAPI: HL-DT-STDVD-ROM GDRH20N, 0D04, max UDMA/100
[ 537.718573] ata2.00: configured for UDMA/100
[ 538.036669] ata3: SATA link down (SStatus 0 SControl 300)
[ 538.356479] ata4: SATA link down (SStatus 0 SControl 300)
[ 539.941038] usb-storage: device scan complete
[ 539.945167] scsi 6:0:0:0: Direct-Access Generic Flash HS-CF
4.44 PQ: 0 ANSI: 0
[ 539.948287] scsi 6:0:0:1: Direct-Access Generic Flash HS-COMBO
4.44 PQ: 0 ANSI: 0
[ 539.955431] sd 6:0:0:0: [sda] Attached SCSI removable disk
[ 540.003487] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 540.004648] sd 6:0:0:1: [sdb] Attached SCSI removable disk
[ 540.007024] sd 6:0:0:0: Attached scsi generic sg0 type 0
[ 540.007036] sd 6:0:0:1: Attached scsi generic sg1 type 0
[ 540.161100] ata5.00: ATAPI: HL-DT-ST DVD+/-RW GSA-H73N, B103, max UDMA/100
[ 540.318055] ata5.00: configured for UDMA/100
[ 540.635121] ata6: SATA link down (SStatus 0 SControl 300)
[ 540.635203] scsi 0:0:0:0: Direct-Access ATA SAMSUNG
HD321KJ CP10 PQ: 0 ANSI: 5
[ 540.635269] sd 0:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
[ 540.635279] sd 0:0:0:0: [sdc] Write Protect is off
[ 540.635280] sd 0:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 540.635294] sd 0:0:0:0: [sdc] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 540.635329] sd 0:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
[ 540.635334] sd 0:0:0:0: [sdc] Write Protect is off
[ 540.635336] sd 0:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 540.635344] sd 0:0:0:0: [sdc] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 540.635346] sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 sdc6 sdc7 >
[ 540.750539] sd 0:0:0:0: [sdc] Attached SCSI disk
[ 540.750566] sd 0:0:0:0: Attached scsi generic sg2 type 0
[ 540.751894] scsi 1:0:0:0: CD-ROM HL-DT-ST DVD-ROM
GDRH20N 0D04 PQ: 0 ANSI: 5
[ 540.751949] scsi 1:0:0:0: Attached scsi generic sg3 type 5
[ 540.753391] scsi 4:0:0:0: CD-ROM HL-DT-ST DVD+-RW
GSA-H73N B103 PQ: 0 ANSI: 5
[ 540.753445] scsi 4:0:0:0: Attached scsi generic sg4 type 5
[ 540.763791] sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
[ 540.763793] Uniform CD-ROM driver Revision: 3.20
[ 540.763819] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 540.769765] sr1: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 540.769789] sr 4:0:0:0: Attached scsi CD-ROM sr1
[ 541.102476] kjournald starting. Commit interval 5 seconds
[ 541.102480] EXT3-fs: mounted filesystem with ordered data mode.
[ 546.203870] input: Power Button (FF) as /class/input/input3
[ 546.299752] ACPI: Power Button (FF) [PWRF]
[ 546.299786] input: Power Button (CM) as /class/input/input4
[ 546.363711] ACPI: Power Button (CM) [PWRB]
[ 546.487943] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 546.640760] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 546.674269] e1000e: Intel(R) PRO/1000 Network Driver - 0.2.0
[ 546.674271] e1000e: Copyright (c) 1999-2007 Intel Corporation.
[ 546.674303] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level,
low) -> IRQ 21
[ 546.674310] PCI: Setting latency timer of device 0000:00:19.0 to 64
[ 546.697158] Linux agpgart interface v0.102
[ 546.716738] iTCO_vendor_support: vendor-support=0
[ 546.739505] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[ 546.739557] iTCO_wdt: Found a ICH9R TCO device (Version=2, TCOBASE=0x0460)
[ 546.739582] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 546.767114] 0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1)
00:1a:a0:9e:5d:da
[ 546.767116] 0000:00:19.0: eth0: Intel(R) PRO/10/100 Network Connection
[ 546.767149] 0000:00:19.0: eth0: MAC: 5, PHY: 7, PBA No: ffffff-0ff
[ 546.806199] input: PC Speaker as /class/input/input5
[ 547.042707] lp: driver loaded but no devices found
[ 547.114483] Adding 4192924k swap on /dev/sdc6. Priority:-1
extents:1 across:4192924k
[ 547.325351] EXT3 FS on sdc7, internal journal
[ 547.624927] kjournald starting. Commit interval 5 seconds
[ 547.625207] EXT3 FS on sdc5, internal journal
[ 547.625210] EXT3-fs: mounted filesystem with ordered data mode.
[ 548.374306] No dock devices found.
[ 548.441759] toshiba_acpi: Unknown parameter `hotkeys_over_acpi'
[ 550.577482] NET: Registered protocol family 10
[ 550.577616] lo: Disabled Privacy Extensions
[ 550.577824] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 550.788414] ppdev: user-space parallel port driver
[ 551.103264] 0000:00:19.0: eth0: Link is Up 100 Mbps Full Duplex,
Flow Control: RX/TX
[ 551.103267] 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[ 551.104041] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 551.345945] Bluetooth: Core ver 2.11
[ 551.345981] NET: Registered protocol family 31
[ 551.345982] Bluetooth: HCI device and connection manager initialized
[ 551.345984] Bluetooth: HCI socket layer initialized
[ 551.356948] Bluetooth: L2CAP ver 2.9
[ 551.356951] Bluetooth: L2CAP socket layer initialized
[ 551.425076] Bluetooth: RFCOMM socket layer initialized
[ 551.425083] Bluetooth: RFCOMM TTY layer initialized
[ 551.425084] Bluetooth: RFCOMM ver 1.8
[ 555.581291] NET: Registered protocol family 17
[ 567.758935] eth0: no IPv6 routers present

Full up dmesg:

[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 2.6.24-rc5-custom (root@machine) (gcc
version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP
Wed Dec 12 23:18:52 EST 2007
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 0000000000099c00 (usable)
[ 0.000000] BIOS-e820: 0000000000099c00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fe90000 (usable)
[ 0.000000] BIOS-e820: 000000007fe90000 - 000000007fee3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007fee3000 - 000000007fef0000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007fef0000 - 000000007ff00000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] 1150MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f3f00
[ 0.000000] Entering add_active_range(0, 0, 523920) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 523920
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 523920
[ 0.000000] On node 0 totalpages: 523920
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2301 pages used for memmap
[ 0.000000] HighMem zone: 292243 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.5 present.
[ 0.000000] ACPI: RSDP 000F97A0, 0024 (r2 DELL )
[ 0.000000] ACPI: XSDT 7FEE3080, 005C (r1 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: FACP 7FEE7200, 00F4 (r3 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: DSDT 7FEE3200, 3FFC (r1 DELL AWRDACPI 1000
MSFT 3000000)
[ 0.000000] ACPI: FACS 7FE90000, 0040
[ 0.000000] ACPI: HPET 7FEE73C0, 0038 (r1 DELL FX09 42302E31
AWRD 98)
[ 0.000000] ACPI: MCFG 7FEE7400, 003C (r1 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: SLIC 7FEE7440, 0176 (r1 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: DMY2 7FEE75C0, 0080 (r1 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: APIC 7FEE7300, 0084 (r1 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: SSDT 7FEE7CA0, 0380 (r1 PmRef CpuPm 3000
INTL 20041203)
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:15 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 6:15 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: Skipping IOAPIC probe due to 'noapic' option.
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] Using ACPI for processor (LAPIC) configuration information
[ 0.000000] Intel MultiProcessor Specification v1.4
[ 0.000000] Virtual Wire compatibility mode.
[ 0.000000] OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
[ 0.000000] I/O APIC #4 Version 17 at 0xFEC00000.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Processors: 2
[ 0.000000] Allocating PCI resources starting at 80000000 (gap:
7ff00000:60100000)
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 519827
[ 0.000000] Kernel command line:
root=UUID=8420f2d5-9569-476d-b3fc-6365a9987426 ro nosmp
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 2992.584 MHz processor.
[ 31.342917] Console: colour VGA+ 80x25
[ 31.342919] console [tty0] enabled
[ 31.345450] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 31.345647] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 31.405054] Memory: 2028720k/2095680k available (2069k kernel code,
65644k reserved, 958k data, 360k init, 1178176k highmem)
[ 31.405110] virtual kernel memory layout:
[ 31.405111] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 31.405111] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 31.405112] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 31.405113] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 31.405113] .init : 0xc03fb000 - 0xc0455000 ( 360 kB)
[ 31.405114] .data : 0xc0305408 - 0xc03f4d84 ( 958 kB)
[ 31.405114] .text : 0xc0100000 - 0xc0305408 (2069 kB)
[ 31.405422] Checking if this processor honours the WP bit even in
supervisor mode... Ok.
[ 31.405522] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4,
CPUs=2, Nodes=1
[ 31.405655] hpet clockevent registered
[ 31.485614] Calibrating delay using timer specific routine..
5988.92 BogoMIPS (lpj=11977856)
[ 31.485703] Security Framework initialized
[ 31.485744] SELinux: Disabled at boot.
[ 31.485783] Capability LSM initialized
[ 31.485827] Mount-cache hash table entries: 512
[ 31.485938] Initializing cgroup subsys cpuacct
[ 31.485982] CPU: After generic identify, caps: bfebfbff 20100000
00000000 00000000 0000e3fd 00000000 00000001 00000000
[ 31.485986] monitor/mwait feature present.
[ 31.486024] using mwait in idle threads.
[ 31.486063] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 31.486127] CPU: L2 cache: 4096K
[ 31.486165] CPU: Physical Processor ID: 0
[ 31.486203] CPU: Processor Core ID: 0
[ 31.486241] CPU: After all inits, caps: bfebfbff 20100000 00000000
00003940 0000e3fd 00000000 00000001 00000000
[ 31.486246] Compat vDSO mapped to ffffe000.
[ 31.486290] Checking 'hlt' instruction... OK.
[ 31.501898] SMP alternatives: switching to UP code
[ 31.502858] ACPI: Core revision 20070126
[ 31.503978] ACPI: setting ELCR to 0200 (from 0e38)
[ 31.559623] CPU0: Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz stepping 0b
[ 31.559717] SMP mode deactivated, forcing use of dummy APIC emulation.
[ 31.559779] Brought up 1 CPUs
[ 31.559823] CPU0 attaching sched-domain:
[ 31.559825] domain 0: span 01
[ 31.559826] groups: 01
[ 31.559920] net_namespace: 64 bytes
[ 31.559962] Booting paravirtualized kernel on bare hardware
[ 31.560254] Time: 3:49:43 Date: 12/14/07
[ 31.560314] NET: Registered protocol family 16
[ 31.560443] EISA bus registered
[ 31.560482] ACPI: bus type pci registered
[ 31.560562] PCI: Using MMCONFIG
[ 31.560912] Setting up standard PCI resources
[ 31.562688] ACPI: EC: Look up EC in DSDT
[ 31.564797] ACPI: Interpreter enabled
[ 31.564836] ACPI: (supports S0 S3 S5)
[ 31.564955] ACPI: Using PIC for interrupt routing
[ 31.567321] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 31.567911] PCI: Transparent bridge - 0000:00:1e.0
[ 31.567963] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 31.568110] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 31.576182] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[ 31.576593] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11
12 14 15) *0, disabled.
[ 31.577062] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11 12 14 15)
[ 31.577471] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 31.577896] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[ 31.578305] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 31.578715] ACPI: PCI Interrupt Link [LNK0] (IRQs *3 4 5 7 9 10 11 12 14 15)
[ 31.579124] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 *4 5 7 9 10 11 12 14 15)
[ 31.579556] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 31.579609] pnp: PnP ACPI init
[ 31.579648] ACPI: bus type pnp registered
[ 31.580598] pnpacpi: exceeded the max number of mem resources: 12
[ 31.580665] pnp: PnP ACPI: found 11 devices
[ 31.580703] ACPI: ACPI bus type pnp unregistered
[ 31.580742] PnPBIOS: Disabled by ACPI PNP
[ 31.580858] PCI: Using ACPI for IRQ routing
[ 31.580897] PCI: If a device doesn't work, try "pci=routeirq". If
it helps, post a report
[ 31.589573] NET: Registered protocol family 8
[ 31.589613] NET: Registered protocol family 20
[ 31.589676] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 31.589855] hpet0: 4 64-bit timers, 14318180 Hz
[ 31.593552] Time: tsc clocksource has been installed.
[ 31.601574] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 31.601616] system 00:01: ioport range 0x800-0x87f has been reserved
[ 31.601659] system 00:01: ioport range 0x290-0x297 has been reserved
[ 31.601701] system 00:01: ioport range 0x880-0x88f has been reserved
[ 31.601747] system 00:07: ioport range 0x400-0x4bf has been reserved
[ 31.601794] system 00:09: iomem range 0xe0000000-0xefffffff could
not be reserved
[ 31.601845] system 00:0a: iomem range 0xf0000-0xfffff could not be reserved
[ 31.601885] system 00:0a: iomem range 0x7ff00000-0x7fffffff has been reserved
[ 31.601926] system 00:0a: iomem range 0xfed00000-0xfed000ff could
not be reserved
[ 31.601975] system 00:0a: iomem range 0x7fe90000-0x7fefffff could
not be reserved
[ 31.602024] system 00:0a: iomem range 0x0-0x9ffff could not be reserved
[ 31.602064] system 00:0a: iomem range 0x100000-0x7fe8ffff could not
be reserved
[ 31.602113] system 00:0a: iomem range 0xfec00000-0xfec00fff could
not be reserved
[ 31.602161] system 00:0a: iomem range 0xfed14000-0xfed1dfff could
not be reserved
[ 31.602210] system 00:0a: iomem range 0xfed20000-0xfed9ffff could
not be reserved
[ 31.602259] system 00:0a: iomem range 0xfee00000-0xfee00fff could
not be reserved
[ 31.602308] system 00:0a: iomem range 0xffb00000-0xffb7ffff could
not be reserved
[ 31.602357] system 00:0a: iomem range 0xfff00000-0xffffffff could
not be reserved
[ 31.632592] PCI: Bridge: 0000:00:01.0
[ 31.632630] IO window: d000-dfff
[ 31.632667] MEM window: f8000000-fbffffff
[ 31.632705] PREFETCH window: d0000000-dfffffff
[ 31.632743] PCI: Bridge: 0000:00:1e.0
[ 31.632781] IO window: c000-cfff
[ 31.632819] MEM window: fdd00000-fddfffff
[ 31.632858] PREFETCH window: fde00000-fdefffff
[ 31.632974] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
[ 31.633013] PCI: setting IRQ 5 as level-triggered
[ 31.633016] ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] ->
GSI 5 (level, low) -> IRQ 5
[ 31.633119] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 31.633124] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 31.633128] NET: Registered protocol family 2
[ 31.669555] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 31.669752] TCP established hash table entries: 131072 (order: 8,
1048576 bytes)
[ 31.670148] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 31.670351] TCP: Hash tables configured (established 131072 bind 65536)
[ 31.670391] TCP reno registered
[ 31.681591] checking if image is initramfs...<7>Switched to high
resolution mode on CPU 0
[ 540.133678] Clocksource tsc unstable (delta = 299978139535 ns)
[ 540.137708] Time: hpet clocksource has been installed.
[ 540.432798] it is
[ 541.570364] Freeing initrd memory: 44428k freed
[ 541.570748] audit: initializing netlink socket (disabled)
[ 541.570794] audit(1197604693.408:1): initialized
[ 541.570951] highmem bounce pool size: 64 pages
[ 541.571919] VFS: Disk quotas dquot_6.5.1
[ 541.571991] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 541.572094] io scheduler noop registered
[ 541.572132] io scheduler anticipatory registered
[ 541.572171] io scheduler deadline registered
[ 541.572213] io scheduler cfq registered (default)
[ 541.572341] Boot video device is 0000:01:00.0
[ 541.572393] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 541.572402] assign_interrupt_mode Found MSI capability
[ 541.572449] Allocate Port Service[0000:00:01.0:pcie00]
[ 541.572467] Allocate Port Service[0000:00:01.0:pcie03]
[ 541.572573] isapnp: Scanning for PnP cards...
[ 541.925441] isapnp: No Plug & Play device found
[ 541.936166] Real Time Clock Driver v1.12ac
[ 541.936299] hpet_resources: 0xfed00000 is busy
[ 541.936314] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports,
IRQ sharing enabled
[ 541.936949] RAMDISK driver initialized: 16 RAM disks of 65536K size
1024 blocksize
[ 541.937028] input: Macintosh mouse button emulation as /class/input/input0
[ 541.937134] PNP: No PS/2 controller found. Probing ports directly.
[ 541.937426] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 541.937466] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 541.944799] mice: PS/2 mouse device common for all mice
[ 541.944899] EISA: Probing bus 0 at eisa.0
[ 541.944955] EISA: Detected 0 cards.
[ 541.945030] TCP cubic registered
[ 541.945070] NET: Registered protocol family 1
[ 541.945121] Using IPI No-Shortcut mode
[ 541.945217] Magic number: 3:192:816
[ 541.945276] hash matches device ptypd
[ 541.945406] Freeing unused kernel memory: 360k freed
[ 542.048433] fuse init (API version 7.9)
[ 542.050972] ACPI: Fan [FAN] (on)
[ 542.053780] ACPI: SSDT 7FEE7680, 022A (r1 PmRef Cpu0Ist 3000
INTL 20040311)
[ 542.053952] ACPI Exception (processor_core-0816): AE_NOT_FOUND,
Processor Device is not present [20070126]
[ 542.054059] ACPI Exception (processor_core-0816): AE_NOT_FOUND,
Processor Device is not present [20070126]
[ 542.054165] ACPI Exception (processor_core-0816): AE_NOT_FOUND,
Processor Device is not present [20070126]
[ 542.055031] ACPI: Thermal Zone [THRM] (40 C)
[ 542.426670] usbcore: registered new interface driver usbfs
[ 542.426727] usbcore: registered new interface driver hub
[ 542.428379] usbcore: registered new device driver usb
[ 542.431483] USB Universal Host Controller Interface driver v3.0
[ 542.431554] ACPI: PCI Interrupt 0000:00:1a.0[A] -> Link [LNKA] ->
GSI 5 (level, low) -> IRQ 5
[ 542.431660] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 542.431662] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 542.431805] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned
bus number 1
[ 542.431872] uhci_hcd 0000:00:1a.0: irq 5, io base 0x0000fe00
[ 542.431977] usb usb1: configuration #1 chosen from 1 choice
[ 542.432027] hub 1-0:1.0: USB hub found
[ 542.432066] hub 1-0:1.0: 2 ports detected
[ 542.478422] SCSI subsystem initialized
[ 542.491096] libata version 3.00 loaded.
[ 542.532455] ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
[ 542.532497] PCI: setting IRQ 11 as level-triggered
[ 542.532500] ACPI: PCI Interrupt 0000:00:1a.1[B] -> Link [LNKF] ->
GSI 11 (level, low) -> IRQ 11
[ 542.532607] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 542.532609] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 542.532660] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned
bus number 2
[ 542.532727] uhci_hcd 0000:00:1a.1: irq 11, io base 0x0000fd00
[ 542.532821] usb usb2: configuration #1 chosen from 1 choice
[ 542.532870] hub 2-0:1.0: USB hub found
[ 542.532910] hub 2-0:1.0: 2 ports detected
[ 542.636416] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[ 542.636463] ACPI: PCI Interrupt 0000:00:1a.2[D] -> Link [LNKD] ->
GSI 11 (level, low) -> IRQ 11
[ 542.636568] PCI: Setting latency timer of device 0000:00:1a.2 to 64
[ 542.636570] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 542.636619] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned
bus number 3
[ 542.636684] uhci_hcd 0000:00:1a.2: irq 11, io base 0x0000fc00
[ 542.636773] usb usb3: configuration #1 chosen from 1 choice
[ 542.636823] hub 3-0:1.0: USB hub found
[ 542.636862] hub 3-0:1.0: 2 ports detected
[ 542.740329] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 4
[ 542.740376] PCI: setting IRQ 4 as level-triggered
[ 542.740378] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNK1] ->
GSI 4 (level, low) -> IRQ 4
[ 542.740482] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 542.740484] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 542.740533] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned
bus number 4
[ 542.740597] uhci_hcd 0000:00:1d.0: irq 4, io base 0x0000fb00
[ 542.740687] usb usb4: configuration #1 chosen from 1 choice
[ 542.740737] hub 4-0:1.0: USB hub found
[ 542.740775] hub 4-0:1.0: 2 ports detected
[ 542.844156] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] ->
GSI 11 (level, low) -> IRQ 11
[ 542.844267] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 542.844269] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 542.844324] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned
bus number 5
[ 542.844387] uhci_hcd 0000:00:1d.1: irq 11, io base 0x0000fa00
[ 542.844476] usb usb5: configuration #1 chosen from 1 choice
[ 542.844526] hub 5-0:1.0: USB hub found
[ 542.844565] hub 5-0:1.0: 2 ports detected
[ 542.876080] usb 2-2: new full speed USB device using uhci_hcd and address 2
[ 542.948202] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 9
[ 542.948249] PCI: setting IRQ 9 as level-triggered
[ 542.948251] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] ->
GSI 9 (level, low) -> IRQ 9
[ 542.948354] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 542.948356] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 542.948405] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned
bus number 6
[ 542.948469] uhci_hcd 0000:00:1d.2: irq 9, io base 0x0000f900
[ 542.948558] usb usb6: configuration #1 chosen from 1 choice
[ 542.948608] hub 6-0:1.0: USB hub found
[ 542.948646] hub 6-0:1.0: 2 ports detected
[ 543.019577] usb 2-2: configuration #1 chosen from 1 choice
[ 543.022538] hub 2-2:1.0: USB hub found
[ 543.024522] hub 2-2:1.0: 2 ports detected
[ 543.052314] ACPI: PCI Interrupt 0000:00:1a.7[C] -> Link [LNKC] ->
GSI 9 (level, low) -> IRQ 9
[ 543.052419] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 543.052421] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 543.052471] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned
bus number 7
[ 543.056417] PCI: cache line size of 32 is not supported by device
0000:00:1a.7
[ 543.056419] ehci_hcd 0000:00:1a.7: irq 9, io mem 0xfdffe000
[ 543.071958] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00,
driver 10 Dec 2004
[ 543.072086] usb usb7: configuration #1 chosen from 1 choice
[ 543.072136] hub 7-0:1.0: USB hub found
[ 543.072175] hub 7-0:1.0: 6 ports detected
[ 543.133464] hub 2-2:1.0: hub_port_status failed (err = -71)
[ 543.134460] hub 2-2:1.0: hub_port_status failed (err = -71)
[ 543.175962] ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNK1] ->
GSI 4 (level, low) -> IRQ 4
[ 543.176074] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 543.176077] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 543.176133] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned
bus number 8
[ 543.180069] PCI: cache line size of 32 is not supported by device
0000:00:1d.7
[ 543.180072] ehci_hcd 0000:00:1d.7: irq 4, io mem 0xfdffd000
[ 543.195882] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00,
driver 10 Dec 2004
[ 543.195999] usb usb8: configuration #1 chosen from 1 choice
[ 543.196056] hub 8-0:1.0: USB hub found
[ 543.196102] hub 8-0:1.0: 6 ports detected
[ 543.300061] ahci 0000:00:1f.2: version 3.0
[ 543.300070] ACPI: PCI Interrupt 0000:00:1f.2[A] -> Link [LNKD] ->
GSI 11 (level, low) -> IRQ 11
[ 543.423749] usb 7-4: new high speed USB device using ehci_hcd and address 2
[ 543.556064] usb 7-4: configuration #1 chosen from 1 choice
[ 543.556473] hub 7-4:1.0: USB hub found
[ 543.556625] hub 7-4:1.0: 2 ports detected
[ 543.659659] usb 2-2: USB disconnect, address 2
[ 543.987521] usb 7-4.1: new high speed USB device using ehci_hcd and address 3
[ 544.079769] usb 7-4.1: configuration #1 chosen from 1 choice
[ 544.080166] hub 7-4.1:1.0: USB hub found
[ 544.080337] hub 7-4.1:1.0: 4 ports detected
[ 544.303228] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3
Gbps 0x3f impl RAID mode
[ 544.303281] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pmp
pio slum part
[ 544.303332] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 544.303515] scsi0 : ahci
[ 544.303632] scsi1 : ahci
[ 544.303735] scsi2 : ahci
[ 544.303836] scsi3 : ahci
[ 544.303938] scsi4 : ahci
[ 544.304039] scsi5 : ahci
[ 544.304127] ata1: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc100 irq 222
[ 544.304176] ata2: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc180 irq 222
[ 544.304225] ata3: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc200 irq 222
[ 544.304274] ata4: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc280 irq 222
[ 544.304323] ata5: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc300 irq 222
[ 544.304372] ata6: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc380 irq 222
[ 544.383303] usb 7-4.1.1: new high speed USB device using ehci_hcd
and address 4
[ 544.562009] usb 7-4.1.1: configuration #1 chosen from 1 choice
[ 544.759091] usb 7-4.1.3: new low speed USB device using ehci_hcd
and address 5
[ 544.870209] usb 7-4.1.3: configuration #1 chosen from 1 choice
[ 545.070798] usb 7-4.1.4: new low speed USB device using ehci_hcd
and address 6
[ 545.193413] usb 7-4.1.4: configuration #1 chosen from 1 choice
[ 545.203045] usbcore: registered new interface driver libusual
[ 545.203119] usbcore: registered new interface driver hiddev
[ 545.206830] Initializing USB Mass Storage driver...
[ 545.207687] input: USB Optical Mouse as /class/input/input1
[ 545.207925] scsi6 : SCSI emulation for USB Mass Storage devices
[ 545.208166] usb-storage: device found at 4
[ 545.208167] usb-storage: waiting for device to settle before scanning
[ 545.214695] input: USB HID v1.11 Mouse [USB Optical Mouse] on
usb-0000:00:1a.7-4.1.3
[ 545.222600] input: Dell Dell USB Keyboard as /class/input/input2
[ 545.234650] input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard]
on usb-0000:00:1a.7-4.1.4
[ 545.234765] usbcore: registered new interface driver usbhid
[ 545.234807] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 545.234889] usbcore: registered new interface driver usb-storage
[ 545.234929] USB Mass Storage support registered.
[ 545.950210] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 545.970798] ata1.00: ATA-8: SAMSUNG HD321KJ, CP100-12, max UDMA7
[ 545.970841] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 545.972864] ata1.00: configured for UDMA/133
[ 547.617195] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 547.773767] ata2.00: ATAPI: HL-DT-STDVD-ROM GDRH20N, 0D04, max UDMA/100
[ 547.929692] ata2.00: configured for UDMA/100
[ 548.248809] ata3: SATA link down (SStatus 0 SControl 300)
[ 548.568613] ata4: SATA link down (SStatus 0 SControl 300)
[ 550.209223] usb-storage: device scan complete
[ 550.213224] scsi 6:0:0:0: Direct-Access Generic Flash HS-CF
4.44 PQ: 0 ANSI: 0
[ 550.215610] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 550.216594] scsi 6:0:0:1: Direct-Access Generic Flash HS-COMBO
4.44 PQ: 0 ANSI: 0
[ 550.225358] sd 6:0:0:0: [sda] Attached SCSI removable disk
[ 550.274575] sd 6:0:0:1: [sdb] Attached SCSI removable disk
[ 550.278679] sd 6:0:0:0: Attached scsi generic sg0 type 0
[ 550.278729] sd 6:0:0:1: Attached scsi generic sg1 type 0
[ 550.373274] ata5.00: ATAPI: HL-DT-ST DVD+/-RW GSA-H73N, B103, max UDMA/100
[ 550.529147] ata5.00: configured for UDMA/100
[ 550.847227] ata6: SATA link down (SStatus 0 SControl 300)
[ 550.847337] scsi 0:0:0:0: Direct-Access ATA SAMSUNG
HD321KJ CP10 PQ: 0 ANSI: 5
[ 550.847541] sd 0:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
[ 550.847587] sd 0:0:0:0: [sdc] Write Protect is off
[ 550.847626] sd 0:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 550.847634] sd 0:0:0:0: [sdc] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 550.847704] sd 0:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
[ 550.847748] sd 0:0:0:0: [sdc] Write Protect is off
[ 550.847787] sd 0:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 550.847795] sd 0:0:0:0: [sdc] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 550.847845] sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 sdc6 sdc7 >
[ 550.938580] sd 0:0:0:0: [sdc] Attached SCSI disk
[ 550.938640] sd 0:0:0:0: Attached scsi generic sg2 type 0
[ 550.939988] scsi 1:0:0:0: CD-ROM HL-DT-ST DVD-ROM
GDRH20N 0D04 PQ: 0 ANSI: 5
[ 550.940087] scsi 1:0:0:0: Attached scsi generic sg3 type 5
[ 550.941562] scsi 4:0:0:0: CD-ROM HL-DT-ST DVD+-RW
GSA-H73N B103 PQ: 0 ANSI: 5
[ 550.941659] scsi 4:0:0:0: Attached scsi generic sg4 type 5
[ 550.959606] sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
[ 550.959648] Uniform CD-ROM driver Revision: 3.20
[ 550.959707] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 550.966161] sr1: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 550.966233] sr 4:0:0:0: Attached scsi CD-ROM sr1
[ 551.331858] kjournald starting. Commit interval 5 seconds
[ 551.331907] EXT3-fs: mounted filesystem with ordered data mode.
[ 557.225420] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 557.266575] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 557.295343] input: Power Button (FF) as /class/input/input3
[ 557.319294] ACPI: Power Button (FF) [PWRF]
[ 557.319361] input: Power Button (CM) as /class/input/input4
[ 557.331278] Linux agpgart interface v0.102
[ 557.339278] ACPI: Power Button (CM) [PWRB]
[ 557.413990] e1000e: Intel(R) PRO/1000 Network Driver - 0.2.0
[ 557.414033] e1000e: Copyright (c) 1999-2007 Intel Corporation.
[ 557.414193] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
[ 557.414233] PCI: setting IRQ 10 as level-triggered
[ 557.414236] ACPI: PCI Interrupt 0000:00:19.0[A] -> Link [LNKE] ->
GSI 10 (level, low) -> IRQ 10
[ 557.414343] PCI: Setting latency timer of device 0000:00:19.0 to 64
[ 557.500916] 0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1)
00:1a:a0:9e:5d:da
[ 557.500967] 0000:00:19.0: eth0: Intel(R) PRO/10/100 Network Connection
[ 557.501027] 0000:00:19.0: eth0: MAC: 5, PHY: 7, PBA No: ffffff-0ff
[ 558.003555] iTCO_vendor_support: vendor-support=0
[ 558.030852] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[ 558.030952] iTCO_wdt: Found a ICH9R TCO device (Version=2, TCOBASE=0x0460)
[ 558.031021] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 558.098079] input: PC Speaker as /class/input/input5
[ 558.523498] lp: driver loaded but no devices found
[ 558.602763] Adding 4192924k swap on /dev/sdc6. Priority:-1
extents:1 across:4192924k
[ 558.920746] EXT3 FS on sdc7, internal journal
[ 559.247666] kjournald starting. Commit interval 5 seconds
[ 559.247879] EXT3 FS on sdc5, internal journal
[ 559.247882] EXT3-fs: mounted filesystem with ordered data mode.
[ 560.386045] No dock devices found.
[ 560.445700] toshiba_acpi: Unknown parameter `hotkeys_over_acpi'
[ 562.672338] NET: Registered protocol family 10
[ 562.672439] lo: Disabled Privacy Extensions
[ 562.672623] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 562.874940] ppdev: user-space parallel port driver
[ 563.070326] 0000:00:19.0: eth0: Link is Up 100 Mbps Full Duplex,
Flow Control: RX/TX
[ 563.070328] 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[ 563.070813] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 563.349696] Bluetooth: Core ver 2.11
[ 563.349730] NET: Registered protocol family 31
[ 563.349731] Bluetooth: HCI device and connection manager initialized
[ 563.349733] Bluetooth: HCI socket layer initialized
[ 563.373381] Bluetooth: L2CAP ver 2.9
[ 563.373384] Bluetooth: L2CAP socket layer initialized
[ 563.462046] Bluetooth: RFCOMM socket layer initialized
[ 563.462053] Bluetooth: RFCOMM TTY layer initialized
[ 563.462054] Bluetooth: RFCOMM ver 1.8
[ 567.652069] NET: Registered protocol family 17
[ 579.413819] eth0: no IPv6 routers present

Here is my kernel config. It's based on the ubuntu gutsy config.

#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.24-rc5-custom
# Wed Dec 12 23:16:10 2007
#
# CONFIG_64BIT is not set
CONFIG_X86_32=y
# CONFIG_X86_64 is not set
CONFIG_X86=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_CLOCKSOURCE_WATCHDOG=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_MMU=y
CONFIG_ZONE_DMA=y
CONFIG_QUICKLIST=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_DMI=y
# CONFIG_RWSEM_GENERIC_SPINLOCK is not set
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_CALIBRATE_DELAY=y
# CONFIG_GENERIC_TIME_VSYSCALL is not set
CONFIG_ARCH_SUPPORTS_OPROFILE=y
# CONFIG_ZONE_DMA32 is not set
CONFIG_ARCH_POPULATES_NODE_MAP=y
# CONFIG_AUDIT_ARCH is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_PENDING_IRQ=y
CONFIG_X86_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_X86_TRAMPOLINE=y
CONFIG_KTIME_SCALAR=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"

#
# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BSD_PROCESS_ACCT_V3=y
# CONFIG_TASKSTATS is not set
# CONFIG_USER_NS is not set
# CONFIG_PID_NS is not set
CONFIG_AUDIT=y
# CONFIG_AUDITSYSCALL is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=17
CONFIG_CGROUPS=y
# CONFIG_CGROUP_DEBUG is not set
# CONFIG_CGROUP_NS is not set
CONFIG_CPUSETS=y
CONFIG_FAIR_GROUP_SCHED=y
CONFIG_FAIR_USER_SCHED=y
# CONFIG_FAIR_CGROUP_SCHED is not set
CONFIG_CGROUP_CPUACCT=y
CONFIG_SYSFS_DEPRECATED=y
CONFIG_PROC_PID_CPUSET=y
CONFIG_RELAY=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
CONFIG_EMBEDDED=y
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLUB_DEBUG=y
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y
CONFIG_BLOCK=y
CONFIG_LBD=y
CONFIG_BLK_DEV_IO_TRACE=y
# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_AS is not set
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
CONFIG_PREEMPT_NOTIFIERS=y

#
# Processor type and features
#
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
CONFIG_SMP=y
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_X86_VSMP is not set
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
CONFIG_PARAVIRT=y
CONFIG_PARAVIRT_GUEST=y
# CONFIG_XEN is not set
CONFIG_VMI=y
CONFIG_LGUEST_GUEST=y
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MGEODE_LX is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_MVIAC7 is not set
# CONFIG_MPSC is not set
CONFIG_MCORE2=y
# CONFIG_GENERIC_CPU is not set
CONFIG_X86_GENERIC=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_X86_XADD=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_TSC=y
CONFIG_X86_MINIMUM_CPU_FAMILY=4
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_NR_CPUS=8
CONFIG_SCHED_SMT=y
CONFIG_SCHED_MC=y
# CONFIG_PREEMPT_NONE is not set
CONFIG_PREEMPT_VOLUNTARY=y
# CONFIG_PREEMPT is not set
CONFIG_PREEMPT_BKL=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
# CONFIG_X86_MCE is not set
CONFIG_VM86=y
CONFIG_TOSHIBA=m
CONFIG_I8K=m
CONFIG_X86_REBOOTFIXUPS=y
CONFIG_MICROCODE=m
CONFIG_MICROCODE_OLD_INTERFACE=y
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m
# CONFIG_NOHIGHMEM is not set
CONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not set
CONFIG_VMSPLIT_3G=y
# CONFIG_VMSPLIT_3G_OPT is not set
# CONFIG_VMSPLIT_2G is not set
# CONFIG_VMSPLIT_2G_OPT is not set
# CONFIG_VMSPLIT_1G is not set
CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_HIGHMEM=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_NR_QUICK=1
CONFIG_VIRT_TO_BUS=y
CONFIG_HIGHPTE=y
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
CONFIG_EFI=y
# CONFIG_IRQBALANCE is not set
CONFIG_BOOT_IOREMAP=y
CONFIG_SECCOMP=y
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
CONFIG_KEXEC=y
CONFIG_CRASH_DUMP=y
CONFIG_PHYSICAL_START=0x100000
CONFIG_RELOCATABLE=y
CONFIG_PHYSICAL_ALIGN=0x100000
CONFIG_HOTPLUG_CPU=y
CONFIG_COMPAT_VDSO=y
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y

#
# Power management options
#
CONFIG_PM=y
CONFIG_PM_LEGACY=y
CONFIG_PM_DEBUG=y
# CONFIG_PM_VERBOSE is not set
CONFIG_PM_TRACE=y
CONFIG_PM_SLEEP_SMP=y
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND_SMP_POSSIBLE=y
CONFIG_SUSPEND=y
CONFIG_HIBERNATION_SMP_POSSIBLE=y
# CONFIG_HIBERNATION is not set
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_PROCFS=y
CONFIG_ACPI_PROCFS_POWER=y
CONFIG_ACPI_PROC_EVENT=y
CONFIG_ACPI_AC=m
CONFIG_ACPI_BATTERY=m
CONFIG_ACPI_BUTTON=m
CONFIG_ACPI_VIDEO=m
CONFIG_ACPI_FAN=m
CONFIG_ACPI_DOCK=m
CONFIG_ACPI_BAY=m
CONFIG_ACPI_PROCESSOR=m
CONFIG_ACPI_HOTPLUG_CPU=y
CONFIG_ACPI_THERMAL=m
CONFIG_ACPI_ASUS=m
CONFIG_ACPI_TOSHIBA=m
CONFIG_ACPI_BLACKLIST_YEAR=2000
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=m
CONFIG_ACPI_SBS=m
CONFIG_APM=m
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
# CONFIG_APM_DO_ENABLE is not set
# CONFIG_APM_CPU_IDLE is not set
# CONFIG_APM_DISPLAY_BLANK is not set
# CONFIG_APM_ALLOW_INTS is not set
# CONFIG_APM_REAL_MODE_POWER_OFF is not set

#
# CPU Frequency scaling
#
# CONFIG_CPU_FREQ is not set
# CONFIG_CPU_IDLE is not set

#
# Bus options (PCI etc.)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCIEPORTBUS=y
CONFIG_HOTPLUG_PCI_PCIE=m
CONFIG_PCIEAER=y
CONFIG_ARCH_SUPPORTS_MSI=y
CONFIG_PCI_MSI=y
CONFIG_PCI_LEGACY=y
# CONFIG_PCI_DEBUG is not set
CONFIG_HT_IRQ=y
CONFIG_ISA_DMA_API=y
CONFIG_ISA=y
CONFIG_EISA=y
CONFIG_EISA_VLB_PRIMING=y
CONFIG_EISA_PCI_EISA=y
CONFIG_EISA_VIRTUAL_ROOT=y
CONFIG_EISA_NAMES=y
CONFIG_MCA=y
CONFIG_MCA_LEGACY=y
# CONFIG_MCA_PROC_FS is not set
CONFIG_SCx200=m
CONFIG_SCx200HR_TIMER=m
CONFIG_K8_NB=y
CONFIG_PCCARD=m
# CONFIG_PCMCIA_DEBUG is not set
CONFIG_PCMCIA=m
CONFIG_PCMCIA_LOAD_CIS=y
CONFIG_PCMCIA_IOCTL=y
CONFIG_CARDBUS=y

#
# PC-card bridges
#
CONFIG_YENTA=m
CONFIG_YENTA_O2=y
CONFIG_YENTA_RICOH=y
CONFIG_YENTA_TI=y
CONFIG_YENTA_ENE_TUNE=y
CONFIG_YENTA_TOSHIBA=y
CONFIG_PD6729=m
CONFIG_I82092=m
CONFIG_I82365=m
CONFIG_TCIC=m
CONFIG_PCMCIA_PROBE=y
CONFIG_PCCARD_NONSTATIC=m
CONFIG_HOTPLUG_PCI=m
CONFIG_HOTPLUG_PCI_FAKE=m
CONFIG_HOTPLUG_PCI_COMPAQ=m
CONFIG_HOTPLUG_PCI_COMPAQ_NVRAM=y
CONFIG_HOTPLUG_PCI_IBM=m
CONFIG_HOTPLUG_PCI_ACPI=m
CONFIG_HOTPLUG_PCI_ACPI_IBM=m
CONFIG_HOTPLUG_PCI_CPCI=y
CONFIG_HOTPLUG_PCI_CPCI_ZT5550=m
CONFIG_HOTPLUG_PCI_CPCI_GENERIC=m
CONFIG_HOTPLUG_PCI_SHPC=m

#
# Executable file formats / Emulations
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m

#
# Networking
#
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=m
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
CONFIG_NET_KEY=m
# CONFIG_NET_KEY_MIGRATE is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_ASK_IP_FIB_HASH=y
# CONFIG_IP_FIB_TRIE is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_MULTIPATH=y
CONFIG_IP_ROUTE_VERBOSE=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_TUNNEL=m
CONFIG_INET_TUNNEL=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
CONFIG_INET_LRO=m
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
CONFIG_TCP_MD5SIG=y
CONFIG_IP_VS=m
# CONFIG_IP_VS_DEBUG is not set
CONFIG_IP_VS_TAB_BITS=12

#
# IPVS transport protocol load balancing support
#
CONFIG_IP_VS_PROTO_TCP=y
CONFIG_IP_VS_PROTO_UDP=y
CONFIG_IP_VS_PROTO_ESP=y
CONFIG_IP_VS_PROTO_AH=y

#
# IPVS scheduler
#
CONFIG_IP_VS_RR=m
CONFIG_IP_VS_WRR=m
CONFIG_IP_VS_LC=m
CONFIG_IP_VS_WLC=m
CONFIG_IP_VS_LBLC=m
CONFIG_IP_VS_LBLCR=m
CONFIG_IP_VS_DH=m
CONFIG_IP_VS_SH=m
CONFIG_IP_VS_SED=m
CONFIG_IP_VS_NQ=m

#
# IPVS application helper
#
CONFIG_IP_VS_FTP=m
CONFIG_IPV6=m
CONFIG_IPV6_PRIVACY=y
# CONFIG_IPV6_ROUTER_PREF is not set
# CONFIG_IPV6_OPTIMISTIC_DAD is not set
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
# CONFIG_IPV6_MIP6 is not set
CONFIG_INET6_XFRM_TUNNEL=m
CONFIG_INET6_TUNNEL=m
CONFIG_INET6_XFRM_MODE_TRANSPORT=m
CONFIG_INET6_XFRM_MODE_TUNNEL=m
CONFIG_INET6_XFRM_MODE_BEET=m
CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
CONFIG_IPV6_SIT=m
CONFIG_IPV6_TUNNEL=m
# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_NETLABEL is not set
CONFIG_NETWORK_SECMARK=y
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_BRIDGE_NETFILTER=y

#
# Core Netfilter Configuration
#
CONFIG_NETFILTER_NETLINK=m
CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NETFILTER_NETLINK_LOG=m
CONFIG_NF_CONNTRACK_ENABLED=m
CONFIG_NF_CONNTRACK=m
CONFIG_NF_CT_ACCT=y
CONFIG_NF_CONNTRACK_MARK=y
CONFIG_NF_CONNTRACK_SECMARK=y
CONFIG_NF_CONNTRACK_EVENTS=y
CONFIG_NF_CT_PROTO_GRE=m
CONFIG_NF_CT_PROTO_SCTP=m
# CONFIG_NF_CT_PROTO_UDPLITE is not set
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_FTP=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
CONFIG_NF_CONNTRACK_PPTP=m
# CONFIG_NF_CONNTRACK_SANE is not set
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
CONFIG_NF_CT_NETLINK=m
CONFIG_NETFILTER_XTABLES=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
# CONFIG_NETFILTER_XT_TARGET_TRACE is not set
CONFIG_NETFILTER_XT_TARGET_SECMARK=m
CONFIG_NETFILTER_XT_TARGET_CONNSECMARK=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
# CONFIG_NETFILTER_XT_MATCH_CONNLIMIT is not set
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
CONFIG_NETFILTER_XT_MATCH_DCCP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HELPER=m
CONFIG_NETFILTER_XT_MATCH_LENGTH=m
CONFIG_NETFILTER_XT_MATCH_LIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_QUOTA=m
CONFIG_NETFILTER_XT_MATCH_REALM=m
CONFIG_NETFILTER_XT_MATCH_SCTP=m
CONFIG_NETFILTER_XT_MATCH_STATE=m
CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
CONFIG_NETFILTER_XT_MATCH_STRING=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
# CONFIG_NETFILTER_XT_MATCH_TIME is not set
CONFIG_NETFILTER_XT_MATCH_U32=m
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m

#
# IP: Netfilter Configuration
#
CONFIG_NF_CONNTRACK_IPV4=m
CONFIG_NF_CONNTRACK_PROC_COMPAT=y
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_IPRANGE=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_NF_NAT=m
CONFIG_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_SAME=m
CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_NF_NAT_PROTO_GRE=m
CONFIG_NF_NAT_FTP=m
CONFIG_NF_NAT_IRC=m
CONFIG_NF_NAT_TFTP=m
CONFIG_NF_NAT_AMANDA=m
CONFIG_NF_NAT_PPTP=m
CONFIG_NF_NAT_H323=m
CONFIG_NF_NAT_SIP=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_TTL=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m

#
# IPv6: Netfilter Configuration (EXPERIMENTAL)
#
CONFIG_NF_CONNTRACK_IPV6=m
CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_MATCH_OPTS=m
CONFIG_IP6_NF_MATCH_FRAG=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_OWNER=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_MH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_TARGET_HL=m
CONFIG_IP6_NF_RAW=m

#
# DECnet: Netfilter Configuration
#
CONFIG_DECNET_NF_GRABULATOR=m

#
# Bridge: Netfilter Configuration
#
CONFIG_BRIDGE_NF_EBTABLES=m
CONFIG_BRIDGE_EBT_BROUTE=m
CONFIG_BRIDGE_EBT_T_FILTER=m
CONFIG_BRIDGE_EBT_T_NAT=m
CONFIG_BRIDGE_EBT_802_3=m
CONFIG_BRIDGE_EBT_AMONG=m
CONFIG_BRIDGE_EBT_ARP=m
CONFIG_BRIDGE_EBT_IP=m
CONFIG_BRIDGE_EBT_LIMIT=m
CONFIG_BRIDGE_EBT_MARK=m
CONFIG_BRIDGE_EBT_PKTTYPE=m
CONFIG_BRIDGE_EBT_STP=m
CONFIG_BRIDGE_EBT_VLAN=m
CONFIG_BRIDGE_EBT_ARPREPLY=m
CONFIG_BRIDGE_EBT_DNAT=m
CONFIG_BRIDGE_EBT_MARK_T=m
CONFIG_BRIDGE_EBT_REDIRECT=m
CONFIG_BRIDGE_EBT_SNAT=m
CONFIG_BRIDGE_EBT_LOG=m
CONFIG_BRIDGE_EBT_ULOG=m
CONFIG_IP_DCCP=m
CONFIG_INET_DCCP_DIAG=m
CONFIG_IP_DCCP_ACKVEC=y

#
# DCCP CCIDs Configuration (EXPERIMENTAL)
#
CONFIG_IP_DCCP_CCID2=m
# CONFIG_IP_DCCP_CCID2_DEBUG is not set
CONFIG_IP_DCCP_CCID3=m
CONFIG_IP_DCCP_TFRC_LIB=m
# CONFIG_IP_DCCP_CCID3_DEBUG is not set
CONFIG_IP_DCCP_CCID3_RTO=100

#
# DCCP Kernel Hacking
#
# CONFIG_IP_DCCP_DEBUG is not set
CONFIG_NET_DCCPPROBE=m
CONFIG_IP_SCTP=m
# CONFIG_SCTP_DBG_MSG is not set
# CONFIG_SCTP_DBG_OBJCNT is not set
# CONFIG_SCTP_HMAC_NONE is not set
# CONFIG_SCTP_HMAC_SHA1 is not set
CONFIG_SCTP_HMAC_MD5=y
CONFIG_TIPC=m
# CONFIG_TIPC_ADVANCED is not set
# CONFIG_TIPC_DEBUG is not set
CONFIG_ATM=y
CONFIG_ATM_CLIP=y
# CONFIG_ATM_CLIP_NO_ICMP is not set
CONFIG_ATM_LANE=m
CONFIG_ATM_MPOA=m
CONFIG_ATM_BR2684=m
# CONFIG_ATM_BR2684_IPFILTER is not set
CONFIG_BRIDGE=m
CONFIG_VLAN_8021Q=m
CONFIG_DECNET=m
# CONFIG_DECNET_ROUTER is not set
CONFIG_LLC=y
CONFIG_LLC2=m
CONFIG_IPX=m
# CONFIG_IPX_INTERN is not set
CONFIG_ATALK=m
CONFIG_DEV_APPLETALK=m
CONFIG_LTPC=m
CONFIG_COPS=m
CONFIG_COPS_DAYNA=y
CONFIG_COPS_TANGENT=y
CONFIG_IPDDP=m
CONFIG_IPDDP_ENCAP=y
CONFIG_IPDDP_DECAP=y
CONFIG_X25=m
CONFIG_LAPB=m
CONFIG_ECONET=m
CONFIG_ECONET_AUNUDP=y
CONFIG_ECONET_NATIVE=y
CONFIG_WAN_ROUTER=m
CONFIG_NET_SCHED=y

#
# Queueing/Scheduling
#
CONFIG_NET_SCH_CBQ=m
CONFIG_NET_SCH_HTB=m
CONFIG_NET_SCH_HFSC=m
CONFIG_NET_SCH_ATM=m
CONFIG_NET_SCH_PRIO=m
# CONFIG_NET_SCH_RR is not set
CONFIG_NET_SCH_RED=m
CONFIG_NET_SCH_SFQ=m
CONFIG_NET_SCH_TEQL=m
CONFIG_NET_SCH_TBF=m
CONFIG_NET_SCH_GRED=m
CONFIG_NET_SCH_DSMARK=m
CONFIG_NET_SCH_NETEM=m
CONFIG_NET_SCH_INGRESS=m

#
# Classification
#
CONFIG_NET_CLS=y
CONFIG_NET_CLS_BASIC=m
CONFIG_NET_CLS_TCINDEX=m
CONFIG_NET_CLS_ROUTE4=m
CONFIG_NET_CLS_ROUTE=y
CONFIG_NET_CLS_FW=m
CONFIG_NET_CLS_U32=m
# CONFIG_CLS_U32_PERF is not set
CONFIG_CLS_U32_MARK=y
CONFIG_NET_CLS_RSVP=m
CONFIG_NET_CLS_RSVP6=m
CONFIG_NET_EMATCH=y
CONFIG_NET_EMATCH_STACK=32
CONFIG_NET_EMATCH_CMP=m
CONFIG_NET_EMATCH_NBYTE=m
CONFIG_NET_EMATCH_U32=m
CONFIG_NET_EMATCH_META=m
CONFIG_NET_EMATCH_TEXT=m
CONFIG_NET_CLS_ACT=y
CONFIG_NET_ACT_POLICE=m
CONFIG_NET_ACT_GACT=m
CONFIG_GACT_PROB=y
CONFIG_NET_ACT_MIRRED=m
CONFIG_NET_ACT_IPT=m
# CONFIG_NET_ACT_NAT is not set
CONFIG_NET_ACT_PEDIT=m
CONFIG_NET_ACT_SIMP=m
# CONFIG_NET_CLS_POLICE is not set
# CONFIG_NET_CLS_IND is not set
CONFIG_NET_SCH_FIFO=y

#
# Network testing
#
CONFIG_NET_PKTGEN=m
CONFIG_NET_TCPPROBE=m
CONFIG_HAMRADIO=y

#
# Packet Radio protocols
#
CONFIG_AX25=m
# CONFIG_AX25_DAMA_SLAVE is not set
CONFIG_NETROM=m
CONFIG_ROSE=m

#
# AX.25 network device drivers
#
CONFIG_MKISS=m
CONFIG_6PACK=m
CONFIG_BPQETHER=m
CONFIG_SCC=m
# CONFIG_SCC_DELAY is not set
# CONFIG_SCC_TRXECHO is not set
CONFIG_BAYCOM_SER_FDX=m
CONFIG_BAYCOM_SER_HDX=m
CONFIG_BAYCOM_PAR=m
CONFIG_BAYCOM_EPP=m
CONFIG_YAM=m
CONFIG_IRDA=m

#
# IrDA protocols
#
CONFIG_IRLAN=m
CONFIG_IRNET=m
CONFIG_IRCOMM=m
CONFIG_IRDA_ULTRA=y

#
# IrDA options
#
CONFIG_IRDA_CACHE_LAST_LSAP=y
CONFIG_IRDA_FAST_RR=y
CONFIG_IRDA_DEBUG=y

#
# Infrared-port device drivers
#

#
# SIR device drivers
#
CONFIG_IRTTY_SIR=m

#
# Dongle support
#
CONFIG_DONGLE=y
CONFIG_ESI_DONGLE=m
CONFIG_ACTISYS_DONGLE=m
CONFIG_TEKRAM_DONGLE=m
# CONFIG_TOIM3232_DONGLE is not set
CONFIG_LITELINK_DONGLE=m
CONFIG_MA600_DONGLE=m
CONFIG_GIRBIL_DONGLE=m
CONFIG_MCP2120_DONGLE=m
CONFIG_OLD_BELKIN_DONGLE=m
CONFIG_ACT200L_DONGLE=m
CONFIG_KINGSUN_DONGLE=m
# CONFIG_KSDAZZLE_DONGLE is not set
# CONFIG_KS959_DONGLE is not set

#
# Old SIR device drivers
#

#
# Old Serial dongle support
#

#
# FIR device drivers
#
CONFIG_USB_IRDA=m
CONFIG_SIGMATEL_FIR=m
CONFIG_NSC_FIR=m
CONFIG_WINBOND_FIR=m
CONFIG_TOSHIBA_FIR=m
CONFIG_SMC_IRCC_FIR=m
CONFIG_ALI_FIR=m
CONFIG_VLSI_FIR=m
CONFIG_VIA_FIR=m
CONFIG_MCS_FIR=m
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
CONFIG_BT_RFCOMM=m
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_CMTP=m
CONFIG_BT_HIDP=m

#
# Bluetooth device drivers
#
CONFIG_BT_HCIUSB=m
CONFIG_BT_HCIUSB_SCO=y
CONFIG_BT_HCIBTSDIO=m
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
# CONFIG_BT_HCIUART_LL is not set
CONFIG_BT_HCIBCM203X=m
CONFIG_BT_HCIBPA10X=m
CONFIG_BT_HCIBFUSB=m
CONFIG_BT_HCIDTL1=m
CONFIG_BT_HCIBT3C=m
CONFIG_BT_HCIBLUECARD=m
CONFIG_BT_HCIBTUART=m
CONFIG_BT_HCIVHCI=m
CONFIG_AF_RXRPC=m
# CONFIG_AF_RXRPC_DEBUG is not set
CONFIG_RXKAD=m
CONFIG_FIB_RULES=y

#
# Wireless
#
CONFIG_CFG80211=m
CONFIG_NL80211=y
CONFIG_WIRELESS_EXT=y
CONFIG_MAC80211=m
CONFIG_MAC80211_RCSIMPLE=y
CONFIG_MAC80211_DEBUGFS=y
# CONFIG_MAC80211_DEBUG is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_IEEE80211_CRYPT_WEP=m
CONFIG_IEEE80211_CRYPT_CCMP=m
CONFIG_IEEE80211_CRYPT_TKIP=m
CONFIG_IEEE80211_SOFTMAC=m
# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set
CONFIG_RFKILL=m
CONFIG_RFKILL_INPUT=m
# CONFIG_NET_9P is not set

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=m
CONFIG_MTD=m
# CONFIG_MTD_DEBUG is not set
CONFIG_MTD_CONCAT=m
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_REDBOOT_PARTS=m
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set

#
# User Modules And Translation Layers
#
CONFIG_MTD_CHAR=m
CONFIG_MTD_BLKDEVS=m
CONFIG_MTD_BLOCK=m
CONFIG_MTD_BLOCK_RO=m
CONFIG_FTL=m
CONFIG_NFTL=m
CONFIG_NFTL_RW=y
CONFIG_INFTL=m
CONFIG_RFD_FTL=m
CONFIG_SSFDC=m
# CONFIG_MTD_OOPS is not set

#
# RAM/ROM/Flash chip drivers
#
CONFIG_MTD_CFI=m
CONFIG_MTD_JEDECPROBE=m
CONFIG_MTD_GEN_PROBE=m
# CONFIG_MTD_CFI_ADV_OPTIONS is not set
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
CONFIG_MTD_CFI_INTELEXT=m
CONFIG_MTD_CFI_AMDSTD=m
CONFIG_MTD_CFI_STAA=m
CONFIG_MTD_CFI_UTIL=m
CONFIG_MTD_RAM=m
CONFIG_MTD_ROM=m
CONFIG_MTD_ABSENT=m

#
# Mapping drivers for chip access
#
CONFIG_MTD_COMPLEX_MAPPINGS=y
CONFIG_MTD_PHYSMAP=m
CONFIG_MTD_PHYSMAP_START=0x8000000
CONFIG_MTD_PHYSMAP_LEN=0x4000000
CONFIG_MTD_PHYSMAP_BANKWIDTH=2
CONFIG_MTD_PNC2000=m
CONFIG_MTD_SC520CDP=m
CONFIG_MTD_NETSC520=m
CONFIG_MTD_TS5500=m
CONFIG_MTD_SBC_GXX=m
CONFIG_MTD_SCx200_DOCFLASH=m
CONFIG_MTD_AMD76XROM=m
CONFIG_MTD_ICHXROM=m
CONFIG_MTD_ESB2ROM=m
CONFIG_MTD_CK804XROM=m
CONFIG_MTD_SCB2_FLASH=m
CONFIG_MTD_NETtel=m
CONFIG_MTD_DILNETPC=m
CONFIG_MTD_DILNETPC_BOOTSIZE=0x80000
CONFIG_MTD_L440GX=m
CONFIG_MTD_PCI=m
# CONFIG_MTD_INTEL_VR_NOR is not set
CONFIG_MTD_PLATRAM=m

#
# Self-contained MTD device drivers
#
CONFIG_MTD_PMC551=m
# CONFIG_MTD_PMC551_BUGFIX is not set
# CONFIG_MTD_PMC551_DEBUG is not set
CONFIG_MTD_DATAFLASH=m
CONFIG_MTD_M25P80=m
CONFIG_MTD_SLRAM=m
CONFIG_MTD_PHRAM=m
CONFIG_MTD_MTDRAM=m
CONFIG_MTDRAM_TOTAL_SIZE=4096
CONFIG_MTDRAM_ERASE_SIZE=128
CONFIG_MTD_BLOCK2MTD=m

#
# Disk-On-Chip Device Drivers
#
CONFIG_MTD_DOC2000=m
CONFIG_MTD_DOC2001=m
CONFIG_MTD_DOC2001PLUS=m
CONFIG_MTD_DOCPROBE=m
CONFIG_MTD_DOCECC=m
# CONFIG_MTD_DOCPROBE_ADVANCED is not set
CONFIG_MTD_DOCPROBE_ADDRESS=0
CONFIG_MTD_NAND=m
# CONFIG_MTD_NAND_VERIFY_WRITE is not set
# CONFIG_MTD_NAND_ECC_SMC is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=m
CONFIG_MTD_NAND_DISKONCHIP=m
# CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED is not set
CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0
# CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE is not set
CONFIG_MTD_NAND_CAFE=m
CONFIG_MTD_NAND_CS553X=m
CONFIG_MTD_NAND_NANDSIM=m
CONFIG_MTD_NAND_PLATFORM=m
# CONFIG_MTD_ALAUDA is not set
CONFIG_MTD_ONENAND=m
CONFIG_MTD_ONENAND_VERIFY_WRITE=y
# CONFIG_MTD_ONENAND_OTP is not set
# CONFIG_MTD_ONENAND_2X_PROGRAM is not set
# CONFIG_MTD_ONENAND_SIM is not set

#
# UBI - Unsorted block images
#
CONFIG_MTD_UBI=m
CONFIG_MTD_UBI_WL_THRESHOLD=4096
CONFIG_MTD_UBI_BEB_RESERVE=1
CONFIG_MTD_UBI_GLUEBI=y

#
# UBI debugging options
#
# CONFIG_MTD_UBI_DEBUG is not set
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_SERIAL=m
CONFIG_PARPORT_PC_FIFO=y
# CONFIG_PARPORT_PC_SUPERIO is not set
CONFIG_PARPORT_PC_PCMCIA=m
# CONFIG_PARPORT_GSC is not set
CONFIG_PARPORT_AX88796=m
CONFIG_PARPORT_1284=y
CONFIG_PARPORT_NOT_PC=y
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set

#
# Protocols
#
CONFIG_ISAPNP=y
CONFIG_PNPBIOS=y
CONFIG_PNPBIOS_PROC_FS=y
CONFIG_PNPACPI=y
CONFIG_BLK_DEV=y
CONFIG_BLK_DEV_FD=m
CONFIG_BLK_DEV_XD=m
CONFIG_PARIDE=m

#
# Parallel IDE high-level drivers
#
CONFIG_PARIDE_PD=m
CONFIG_PARIDE_PCD=m
CONFIG_PARIDE_PF=m
CONFIG_PARIDE_PT=m
CONFIG_PARIDE_PG=m

#
# Parallel IDE protocol modules
#
CONFIG_PARIDE_ATEN=m
CONFIG_PARIDE_BPCK=m
CONFIG_PARIDE_BPCK6=m
CONFIG_PARIDE_COMM=m
CONFIG_PARIDE_DSTR=m
CONFIG_PARIDE_FIT2=m
CONFIG_PARIDE_FIT3=m
CONFIG_PARIDE_EPAT=m
# CONFIG_PARIDE_EPATC8 is not set
CONFIG_PARIDE_EPIA=m
CONFIG_PARIDE_FRIQ=m
CONFIG_PARIDE_FRPW=m
CONFIG_PARIDE_KBIC=m
CONFIG_PARIDE_KTTI=m
CONFIG_PARIDE_ON20=m
CONFIG_PARIDE_ON26=m
CONFIG_BLK_CPQ_DA=m
CONFIG_BLK_CPQ_CISS_DA=m
CONFIG_CISS_SCSI_TAPE=y
CONFIG_BLK_DEV_DAC960=m
CONFIG_BLK_DEV_UMEM=m
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_CRYPTOLOOP=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_SX8=m
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=65536
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m
CONFIG_VIRTIO_BLK=m
CONFIG_MISC_DEVICES=y
CONFIG_IBM_ASM=m
CONFIG_PHANTOM=m
CONFIG_EEPROM_93CX6=m
CONFIG_SGI_IOC4=m
CONFIG_TIFM_CORE=m
CONFIG_TIFM_7XX1=m
CONFIG_ASUS_LAPTOP=m
# CONFIG_FUJITSU_LAPTOP is not set
CONFIG_MSI_LAPTOP=m
CONFIG_SONY_LAPTOP=m
CONFIG_SONYPI_COMPAT=y
CONFIG_THINKPAD_ACPI=m
# CONFIG_THINKPAD_ACPI_DEBUG is not set
CONFIG_THINKPAD_ACPI_BAY=y
CONFIG_IDE=y
CONFIG_IDE_MAX_HWIFS=4
CONFIG_BLK_DEV_IDE=m

#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=m
# CONFIG_IDEDISK_MULTI_MODE is not set
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_DELKIN=m
CONFIG_BLK_DEV_IDECD=m
CONFIG_BLK_DEV_IDETAPE=m
CONFIG_BLK_DEV_IDEFLOPPY=m
CONFIG_BLK_DEV_IDESCSI=m
CONFIG_BLK_DEV_IDEACPI=y
# CONFIG_IDE_TASK_IOCTL is not set
CONFIG_IDE_PROC_FS=y

#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=m
CONFIG_BLK_DEV_PLATFORM=m
CONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
CONFIG_BLK_DEV_IDEPNP=y

#
# PCI IDE chipsets support
#
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_IDEPCI_PCIBUS_ORDER is not set
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_GENERIC is not set
CONFIG_BLK_DEV_OPTI621=m
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_BLK_DEV_AEC62XX=m
CONFIG_BLK_DEV_ALI15X3=m
# CONFIG_WDC_ALI15X3 is not set
CONFIG_BLK_DEV_AMD74XX=m
CONFIG_BLK_DEV_ATIIXP=m
CONFIG_BLK_DEV_CMD64X=m
# CONFIG_BLK_DEV_TRIFLEX is not set
CONFIG_BLK_DEV_CY82C693=m
# CONFIG_BLK_DEV_CS5520 is not set
CONFIG_BLK_DEV_CS5530=m
CONFIG_BLK_DEV_CS5535=m
CONFIG_BLK_DEV_HPT34X=m
# CONFIG_HPT34X_AUTODMA is not set
CONFIG_BLK_DEV_HPT366=m
# CONFIG_BLK_DEV_JMICRON is not set
CONFIG_BLK_DEV_SC1200=m
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_IT8213 is not set
# CONFIG_BLK_DEV_IT821X is not set
CONFIG_BLK_DEV_NS87415=m
CONFIG_BLK_DEV_PDC202XX_OLD=m
CONFIG_PDC202XX_BURST=y
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
CONFIG_BLK_DEV_TRM290=m
CONFIG_BLK_DEV_VIA82CXXX=m
CONFIG_BLK_DEV_TC86C001=m
# CONFIG_IDE_ARM is not set

#
# Other IDE chipsets support
#

#
# Note: most of these also require special kernel boot parameters
#
# CONFIG_BLK_DEV_4DRIVES is not set
# CONFIG_BLK_DEV_ALI14XX is not set
# CONFIG_BLK_DEV_DTC2278 is not set
# CONFIG_BLK_DEV_HT6560B is not set
# CONFIG_BLK_DEV_QD65XX is not set
# CONFIG_BLK_DEV_UMC8672 is not set
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDE_ARCH_OBSOLETE_INIT=y
# CONFIG_BLK_DEV_HD is not set

#
# SCSI device support
#
CONFIG_RAID_ATTRS=m
CONFIG_SCSI=m
CONFIG_SCSI_DMA=y
CONFIG_SCSI_TGT=m
CONFIG_SCSI_NETLINK=y
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=m
CONFIG_CHR_DEV_ST=m
CONFIG_CHR_DEV_OSST=m
CONFIG_BLK_DEV_SR=m
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=m
CONFIG_CHR_DEV_SCH=m

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
CONFIG_SCSI_SCAN_ASYNC=y
CONFIG_SCSI_WAIT_SCAN=m

#
# SCSI Transports
#
CONFIG_SCSI_SPI_ATTRS=m
CONFIG_SCSI_FC_ATTRS=m
# CONFIG_SCSI_FC_TGT_ATTRS is not set
CONFIG_SCSI_ISCSI_ATTRS=m
CONFIG_SCSI_SAS_ATTRS=m
CONFIG_SCSI_SAS_LIBSAS=m
# CONFIG_SCSI_SAS_ATA is not set
# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set
CONFIG_SCSI_SRP_ATTRS=m
# CONFIG_SCSI_SRP_TGT_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
CONFIG_ISCSI_TCP=m
CONFIG_BLK_DEV_3W_XXXX_RAID=m
CONFIG_SCSI_3W_9XXX=m
CONFIG_SCSI_7000FASST=m
CONFIG_SCSI_ACARD=m
CONFIG_SCSI_AHA152X=m
CONFIG_SCSI_AHA1542=m
CONFIG_SCSI_AHA1740=m
CONFIG_SCSI_AACRAID=m
CONFIG_SCSI_AIC7XXX=m
CONFIG_AIC7XXX_CMDS_PER_DEVICE=8
CONFIG_AIC7XXX_RESET_DELAY_MS=15000
CONFIG_AIC7XXX_DEBUG_ENABLE=y
CONFIG_AIC7XXX_DEBUG_MASK=0
CONFIG_AIC7XXX_REG_PRETTY_PRINT=y
# CONFIG_SCSI_AIC7XXX_OLD is not set
CONFIG_SCSI_AIC79XX=m
CONFIG_AIC79XX_CMDS_PER_DEVICE=32
CONFIG_AIC79XX_RESET_DELAY_MS=15000
CONFIG_AIC79XX_DEBUG_ENABLE=y
CONFIG_AIC79XX_DEBUG_MASK=0
CONFIG_AIC79XX_REG_PRETTY_PRINT=y
CONFIG_SCSI_AIC94XX=m
# CONFIG_AIC94XX_DEBUG is not set
CONFIG_SCSI_DPT_I2O=m
CONFIG_SCSI_ADVANSYS=m
CONFIG_SCSI_IN2000=m
CONFIG_SCSI_ARCMSR=m
# CONFIG_SCSI_ARCMSR_AER is not set
CONFIG_MEGARAID_NEWGEN=y
CONFIG_MEGARAID_MM=m
CONFIG_MEGARAID_MAILBOX=m
CONFIG_MEGARAID_LEGACY=m
CONFIG_MEGARAID_SAS=m
CONFIG_SCSI_HPTIOP=m
CONFIG_SCSI_BUSLOGIC=m
# CONFIG_SCSI_OMIT_FLASHPOINT is not set
CONFIG_SCSI_DMX3191D=m
CONFIG_SCSI_DTC3280=m
CONFIG_SCSI_EATA=m
CONFIG_SCSI_EATA_TAGGED_QUEUE=y
CONFIG_SCSI_EATA_LINKED_COMMANDS=y
CONFIG_SCSI_EATA_MAX_TAGS=16
CONFIG_SCSI_FUTURE_DOMAIN=m
CONFIG_SCSI_FD_MCS=m
CONFIG_SCSI_GDTH=m
CONFIG_SCSI_GENERIC_NCR5380=m
CONFIG_SCSI_GENERIC_NCR5380_MMIO=m
CONFIG_SCSI_GENERIC_NCR53C400=y
CONFIG_SCSI_IBMMCA=m
CONFIG_IBMMCA_SCSI_ORDER_STANDARD=y
# CONFIG_IBMMCA_SCSI_DEV_RESET is not set
CONFIG_SCSI_IPS=m
CONFIG_SCSI_INITIO=m
CONFIG_SCSI_INIA100=m
CONFIG_SCSI_PPA=m
CONFIG_SCSI_IMM=m
# CONFIG_SCSI_IZIP_EPP16 is not set
# CONFIG_SCSI_IZIP_SLOW_CTR is not set
CONFIG_SCSI_NCR53C406A=m
CONFIG_SCSI_NCR_D700=m
CONFIG_SCSI_STEX=m
CONFIG_SCSI_SYM53C8XX_2=m
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
CONFIG_SCSI_SYM53C8XX_MMIO=y
CONFIG_SCSI_IPR=m
# CONFIG_SCSI_IPR_TRACE is not set
# CONFIG_SCSI_IPR_DUMP is not set
CONFIG_SCSI_NCR_Q720=m
CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS=8
CONFIG_SCSI_NCR53C8XX_MAX_TAGS=4
CONFIG_SCSI_NCR53C8XX_SYNC=5
CONFIG_SCSI_PAS16=m
CONFIG_SCSI_PSI240I=m
CONFIG_SCSI_QLOGIC_FAS=m
CONFIG_SCSI_QLOGIC_1280=m
CONFIG_SCSI_QLA_FC=m
CONFIG_SCSI_QLA_ISCSI=m
CONFIG_SCSI_LPFC=m
CONFIG_SCSI_SEAGATE=m
CONFIG_SCSI_SIM710=m
CONFIG_SCSI_SYM53C416=m
CONFIG_SCSI_DC395x=m
CONFIG_SCSI_DC390T=m
CONFIG_SCSI_T128=m
CONFIG_SCSI_U14_34F=m
CONFIG_SCSI_U14_34F_TAGGED_QUEUE=y
CONFIG_SCSI_U14_34F_LINKED_COMMANDS=y
CONFIG_SCSI_U14_34F_MAX_TAGS=8
CONFIG_SCSI_ULTRASTOR=m
CONFIG_SCSI_NSP32=m
CONFIG_SCSI_DEBUG=m
CONFIG_SCSI_SRP=m
# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set
CONFIG_ATA=m
# CONFIG_ATA_NONSTANDARD is not set
CONFIG_ATA_ACPI=y
CONFIG_SATA_AHCI=m
CONFIG_SATA_SVW=m
CONFIG_ATA_PIIX=m
CONFIG_SATA_MV=m
CONFIG_SATA_NV=m
CONFIG_PDC_ADMA=m
CONFIG_SATA_QSTOR=m
CONFIG_SATA_PROMISE=m
CONFIG_SATA_SX4=m
CONFIG_SATA_SIL=m
CONFIG_SATA_SIL24=m
CONFIG_SATA_SIS=m
CONFIG_SATA_ULI=m
CONFIG_SATA_VIA=m
CONFIG_SATA_VITESSE=m
CONFIG_SATA_INIC162X=m
# CONFIG_PATA_ACPI is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
CONFIG_PATA_CS5520=m
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_CS5535 is not set
# CONFIG_PATA_CS5536 is not set
# CONFIG_PATA_CYPRESS is not set
CONFIG_PATA_EFAR=m
CONFIG_ATA_GENERIC=m
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_ISAPNP is not set
CONFIG_PATA_IT821X=m
CONFIG_PATA_IT8213=m
CONFIG_PATA_JMICRON=m
# CONFIG_PATA_LEGACY is not set
CONFIG_PATA_TRIFLEX=m
CONFIG_PATA_MARVELL=m
CONFIG_PATA_MPIIX=m
CONFIG_PATA_OLDPIIX=m
CONFIG_PATA_NETCELL=m
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
CONFIG_PATA_PCMCIA=m
# CONFIG_PATA_PDC_OLD is not set
CONFIG_PATA_QDI=m
# CONFIG_PATA_RADISYS is not set
CONFIG_PATA_RZ1000=m
# CONFIG_PATA_SC1200 is not set
CONFIG_PATA_SERVERWORKS=m
CONFIG_PATA_PDC2027X=m
CONFIG_PATA_SIL680=m
CONFIG_PATA_SIS=m
# CONFIG_PATA_VIA is not set
CONFIG_PATA_WINBOND=m
# CONFIG_PATA_WINBOND_VLB is not set
# CONFIG_PATA_PLATFORM is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
CONFIG_MD_RAID1=m
CONFIG_MD_RAID10=m
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
CONFIG_MD_MULTIPATH=m
CONFIG_MD_FAULTY=m
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_MULTIPATH_EMC=m
# CONFIG_DM_MULTIPATH_RDAC is not set
# CONFIG_DM_MULTIPATH_HP is not set
# CONFIG_DM_DELAY is not set
# CONFIG_DM_UEVENT is not set
CONFIG_FUSION=y
CONFIG_FUSION_SPI=m
CONFIG_FUSION_FC=m
CONFIG_FUSION_SAS=m
CONFIG_FUSION_MAX_SGE=128
CONFIG_FUSION_CTL=m
CONFIG_FUSION_LAN=m
# CONFIG_FUSION_LOGGING is not set

#
# IEEE 1394 (FireWire) support
#
# CONFIG_FIREWIRE is not set
CONFIG_IEEE1394=m

#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set

#
# Controllers
#
CONFIG_IEEE1394_PCILYNX=m
CONFIG_IEEE1394_OHCI1394=m

#
# Protocols
#
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=m
# CONFIG_IEEE1394_SBP2_PHYS_DMA is not set
CONFIG_IEEE1394_ETH1394_ROM_ENTRY=y
CONFIG_IEEE1394_ETH1394=m
CONFIG_IEEE1394_DV1394=m
CONFIG_IEEE1394_RAWIO=m
CONFIG_I2O=m
CONFIG_I2O_LCT_NOTIFY_ON_CHANGES=y
CONFIG_I2O_EXT_ADAPTEC=y
CONFIG_I2O_CONFIG=m
CONFIG_I2O_CONFIG_OLD_IOCTL=y
CONFIG_I2O_BUS=m
CONFIG_I2O_BLOCK=m
CONFIG_I2O_SCSI=m
CONFIG_I2O_PROC=m
CONFIG_MACINTOSH_DRIVERS=y
CONFIG_MAC_EMUMOUSEBTN=y
CONFIG_NETDEVICES=y
# CONFIG_NETDEVICES_MULTIQUEUE is not set
CONFIG_IFB=m
CONFIG_DUMMY=m
CONFIG_BONDING=m
# CONFIG_MACVLAN is not set
CONFIG_EQUALIZER=m
CONFIG_TUN=m
# CONFIG_VETH is not set
CONFIG_NET_SB1000=m
# CONFIG_IP1000 is not set
CONFIG_ARCNET=m
CONFIG_ARCNET_1201=m
CONFIG_ARCNET_1051=m
CONFIG_ARCNET_RAW=m
CONFIG_ARCNET_CAP=m
CONFIG_ARCNET_COM90xx=m
CONFIG_ARCNET_COM90xxIO=m
CONFIG_ARCNET_RIM_I=m
CONFIG_ARCNET_COM20020=m
CONFIG_ARCNET_COM20020_ISA=m
CONFIG_ARCNET_COM20020_PCI=m
CONFIG_PHYLIB=m

#
# MII PHY device drivers
#
CONFIG_MARVELL_PHY=m
CONFIG_DAVICOM_PHY=m
CONFIG_QSEMI_PHY=m
CONFIG_LXT_PHY=m
CONFIG_CICADA_PHY=m
CONFIG_VITESSE_PHY=m
CONFIG_SMSC_PHY=m
CONFIG_BROADCOM_PHY=m
# CONFIG_ICPLUS_PHY is not set
CONFIG_FIXED_PHY=m
# CONFIG_FIXED_MII_10_FDX is not set
# CONFIG_FIXED_MII_100_FDX is not set
# CONFIG_FIXED_MII_1000_FDX is not set
CONFIG_FIXED_MII_AMNT=1
# CONFIG_MDIO_BITBANG is not set
CONFIG_NET_ETHERNET=y
CONFIG_MII=m
CONFIG_HAPPYMEAL=m
CONFIG_SUNGEM=m
CONFIG_CASSINI=m
CONFIG_NET_VENDOR_3COM=y
CONFIG_EL1=m
CONFIG_EL2=m
CONFIG_ELPLUS=m
CONFIG_EL16=m
CONFIG_EL3=m
CONFIG_3C515=m
CONFIG_ELMC=m
CONFIG_ELMC_II=m
CONFIG_VORTEX=m
CONFIG_TYPHOON=m
CONFIG_LANCE=m
CONFIG_NET_VENDOR_SMC=y
CONFIG_WD80x3=m
CONFIG_ULTRAMCA=m
CONFIG_ULTRA=m
CONFIG_ULTRA32=m
CONFIG_SMC9194=m
CONFIG_NET_VENDOR_RACAL=y
CONFIG_NI52=m
CONFIG_NI65=m
CONFIG_NET_TULIP=y
CONFIG_DE2104X=m
CONFIG_TULIP=m
# CONFIG_TULIP_MWI is not set
# CONFIG_TULIP_MMIO is not set
# CONFIG_TULIP_NAPI is not set
CONFIG_DE4X5=m
CONFIG_WINBOND_840=m
CONFIG_DM9102=m
CONFIG_ULI526X=m
CONFIG_PCMCIA_XIRCOM=m
CONFIG_AT1700=m
CONFIG_DEPCA=m
CONFIG_HP100=m
CONFIG_NET_ISA=y
CONFIG_E2100=m
CONFIG_EWRK3=m
CONFIG_EEXPRESS=m
CONFIG_EEXPRESS_PRO=m
CONFIG_HPLAN_PLUS=m
CONFIG_HPLAN=m
CONFIG_LP486E=m
CONFIG_ETH16I=m
CONFIG_NE2000=m
CONFIG_ZNET=m
CONFIG_SEEQ8005=m
CONFIG_NE2_MCA=m
CONFIG_IBMLANA=m
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
CONFIG_NET_PCI=y
CONFIG_PCNET32=m
# CONFIG_PCNET32_NAPI is not set
CONFIG_AMD8111_ETH=m
# CONFIG_AMD8111E_NAPI is not set
CONFIG_ADAPTEC_STARFIRE=m
# CONFIG_ADAPTEC_STARFIRE_NAPI is not set
CONFIG_AC3200=m
CONFIG_APRICOT=m
CONFIG_B44=m
CONFIG_B44_PCI_AUTOSELECT=y
CONFIG_B44_PCICORE_AUTOSELECT=y
CONFIG_B44_PCI=y
CONFIG_FORCEDETH=m
# CONFIG_FORCEDETH_NAPI is not set
CONFIG_CS89x0=m
CONFIG_EEPRO100=m
CONFIG_E100=m
CONFIG_LNE390=m
CONFIG_FEALNX=m
CONFIG_NATSEMI=m
CONFIG_NE2K_PCI=m
CONFIG_NE3210=m
CONFIG_ES3210=m
CONFIG_8139CP=m
CONFIG_8139TOO=m
# CONFIG_8139TOO_PIO is not set
# CONFIG_8139TOO_TUNE_TWISTER is not set
CONFIG_8139TOO_8129=y
# CONFIG_8139_OLD_RX_RESET is not set
CONFIG_SIS900=m
CONFIG_EPIC100=m
CONFIG_SUNDANCE=m
# CONFIG_SUNDANCE_MMIO is not set
CONFIG_TLAN=m
CONFIG_VIA_RHINE=m
# CONFIG_VIA_RHINE_MMIO is not set
# CONFIG_VIA_RHINE_NAPI is not set
CONFIG_SC92031=m
CONFIG_NET_POCKET=y
CONFIG_ATP=m
CONFIG_DE600=m
CONFIG_DE620=m
CONFIG_NETDEV_1000=y
CONFIG_ACENIC=m
# CONFIG_ACENIC_OMIT_TIGON_I is not set
CONFIG_DL2K=m
CONFIG_E1000=m
CONFIG_E1000_NAPI=y
# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
CONFIG_E1000E=m
CONFIG_NS83820=m
CONFIG_HAMACHI=m
CONFIG_YELLOWFIN=m
CONFIG_R8169=m
# CONFIG_R8169_NAPI is not set
CONFIG_R8169_VLAN=y
CONFIG_SIS190=m
CONFIG_SKGE=m
# CONFIG_SKGE_DEBUG is not set
CONFIG_SKY2=m
# CONFIG_SKY2_DEBUG is not set
# CONFIG_SK98LIN is not set
CONFIG_VIA_VELOCITY=m
CONFIG_TIGON3=m
CONFIG_BNX2=m
CONFIG_QLA3XXX=m
CONFIG_ATL1=m
CONFIG_NETDEV_10000=y
CONFIG_CHELSIO_T1=m
CONFIG_CHELSIO_T1_1G=y
CONFIG_CHELSIO_T1_NAPI=y
CONFIG_CHELSIO_T3=m
CONFIG_IXGBE=m
CONFIG_IXGB=m
# CONFIG_IXGB_NAPI is not set
CONFIG_S2IO=m
# CONFIG_S2IO_NAPI is not set
CONFIG_MYRI10GE=m
CONFIG_NETXEN_NIC=m
# CONFIG_NIU is not set
CONFIG_MLX4_CORE=m
CONFIG_MLX4_DEBUG=y
# CONFIG_TEHUTI is not set
CONFIG_TR=y
CONFIG_IBMTR=m
CONFIG_IBMOL=m
CONFIG_IBMLS=m
CONFIG_3C359=m
CONFIG_TMS380TR=m
CONFIG_TMSPCI=m
CONFIG_SKISA=m
CONFIG_PROTEON=m
CONFIG_ABYSS=m
CONFIG_MADGEMC=m
CONFIG_SMCTR=m

#
# Wireless LAN
#
CONFIG_WLAN_PRE80211=y
CONFIG_STRIP=m
CONFIG_ARLAN=m
CONFIG_WAVELAN=m
CONFIG_PCMCIA_WAVELAN=m
CONFIG_PCMCIA_NETWAVE=m
CONFIG_WLAN_80211=y
CONFIG_PCMCIA_RAYCS=m
CONFIG_IPW2100=m
CONFIG_IPW2100_MONITOR=y
# CONFIG_IPW2100_DEBUG is not set
CONFIG_IPW2200=m
CONFIG_IPW2200_MONITOR=y
CONFIG_IPW2200_RADIOTAP=y
CONFIG_IPW2200_PROMISCUOUS=y
CONFIG_IPW2200_QOS=y
# CONFIG_IPW2200_DEBUG is not set
CONFIG_LIBERTAS=m
CONFIG_LIBERTAS_USB=m
# CONFIG_LIBERTAS_CS is not set
# CONFIG_LIBERTAS_SDIO is not set
# CONFIG_LIBERTAS_DEBUG is not set
CONFIG_AIRO=m
CONFIG_HERMES=m
# CONFIG_PLX_HERMES is not set
# CONFIG_TMD_HERMES is not set
# CONFIG_NORTEL_HERMES is not set
# CONFIG_PCI_HERMES is not set
CONFIG_PCMCIA_HERMES=m
CONFIG_PCMCIA_SPECTRUM=m
CONFIG_ATMEL=m
CONFIG_PCI_ATMEL=m
CONFIG_PCMCIA_ATMEL=m
CONFIG_AIRO_CS=m
CONFIG_PCMCIA_WL3501=m
CONFIG_PRISM54=m
CONFIG_USB_ZD1201=m
# CONFIG_RTL8187 is not set
# CONFIG_ADM8211 is not set
# CONFIG_P54_COMMON is not set
# CONFIG_IWLWIFI is not set
CONFIG_HOSTAP=m
CONFIG_HOSTAP_FIRMWARE=y
CONFIG_HOSTAP_FIRMWARE_NVRAM=y
CONFIG_HOSTAP_PLX=m
CONFIG_HOSTAP_PCI=m
CONFIG_HOSTAP_CS=m
CONFIG_BCM43XX=m
# CONFIG_BCM43XX_DEBUG is not set
CONFIG_BCM43XX_DMA=y
CONFIG_BCM43XX_PIO=y
CONFIG_BCM43XX_DMA_AND_PIO_MODE=y
# CONFIG_BCM43XX_DMA_MODE is not set
# CONFIG_BCM43XX_PIO_MODE is not set
# CONFIG_B43 is not set
# CONFIG_B43LEGACY is not set
CONFIG_ZD1211RW=m
# CONFIG_ZD1211RW_DEBUG is not set
# CONFIG_RT2X00 is not set

#
# USB Network Adapters
#
CONFIG_USB_CATC=m
CONFIG_USB_KAWETH=m
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
CONFIG_USB_USBNET=m
CONFIG_USB_NET_AX8817X=m
CONFIG_USB_NET_CDCETHER=m
CONFIG_USB_NET_DM9601=m
CONFIG_USB_NET_GL620A=m
CONFIG_USB_NET_NET1080=m
CONFIG_USB_NET_PLUSB=m
CONFIG_USB_NET_MCS7830=m
CONFIG_USB_NET_RNDIS_HOST=m
CONFIG_USB_NET_CDC_SUBSET=m
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_BELKIN=y
CONFIG_USB_ARMLINUX=y
CONFIG_USB_EPSON2888=y
CONFIG_USB_KC2190=y
# CONFIG_USB_NET_ZAURUS is not set
CONFIG_NET_PCMCIA=y
CONFIG_PCMCIA_3C589=m
CONFIG_PCMCIA_3C574=m
CONFIG_PCMCIA_FMVJ18X=m
CONFIG_PCMCIA_PCNET=m
CONFIG_PCMCIA_NMCLAN=m
CONFIG_PCMCIA_SMC91C92=m
CONFIG_PCMCIA_XIRC2PS=m
CONFIG_PCMCIA_AXNET=m
CONFIG_ARCNET_COM20020_CS=m
CONFIG_PCMCIA_IBMTR=m
CONFIG_WAN=y
CONFIG_HOSTESS_SV11=m
CONFIG_COSA=m
CONFIG_LANMEDIA=m
CONFIG_SEALEVEL_4021=m
CONFIG_HDLC=m
CONFIG_HDLC_RAW=m
CONFIG_HDLC_RAW_ETH=m
CONFIG_HDLC_CISCO=m
CONFIG_HDLC_FR=m
CONFIG_HDLC_PPP=m
CONFIG_HDLC_X25=m
CONFIG_PCI200SYN=m
CONFIG_WANXL=m
CONFIG_PC300=m
CONFIG_PC300_MLPPP=y

#
# Cyclades-PC300 MLPPP support is disabled.
#

#
# Refer to the file README.mlppp, provided by PC300 package.
#
# CONFIG_PC300TOO is not set
CONFIG_N2=m
CONFIG_C101=m
CONFIG_FARSYNC=m
CONFIG_DSCC4=m
CONFIG_DSCC4_PCISYNC=y
CONFIG_DSCC4_PCI_RST=y
CONFIG_DLCI=m
CONFIG_DLCI_MAX=8
CONFIG_SDLA=m
CONFIG_WAN_ROUTER_DRIVERS=m
CONFIG_CYCLADES_SYNC=m
CONFIG_CYCLOMX_X25=y
CONFIG_LAPBETHER=m
CONFIG_X25_ASY=m
CONFIG_SBNI=m
# CONFIG_SBNI_MULTILINE is not set
CONFIG_ATM_DRIVERS=y
# CONFIG_ATM_DUMMY is not set
CONFIG_ATM_TCP=m
CONFIG_ATM_LANAI=m
CONFIG_ATM_ENI=m
# CONFIG_ATM_ENI_DEBUG is not set
# CONFIG_ATM_ENI_TUNE_BURST is not set
CONFIG_ATM_FIRESTREAM=m
CONFIG_ATM_ZATM=m
# CONFIG_ATM_ZATM_DEBUG is not set
CONFIG_ATM_NICSTAR=m
# CONFIG_ATM_NICSTAR_USE_SUNI is not set
# CONFIG_ATM_NICSTAR_USE_IDT77105 is not set
CONFIG_ATM_IDT77252=m
# CONFIG_ATM_IDT77252_DEBUG is not set
# CONFIG_ATM_IDT77252_RCV_ALL is not set
CONFIG_ATM_IDT77252_USE_SUNI=y
CONFIG_ATM_AMBASSADOR=m
# CONFIG_ATM_AMBASSADOR_DEBUG is not set
CONFIG_ATM_HORIZON=m
# CONFIG_ATM_HORIZON_DEBUG is not set
CONFIG_ATM_IA=m
# CONFIG_ATM_IA_DEBUG is not set
CONFIG_ATM_FORE200E_MAYBE=m
CONFIG_ATM_FORE200E_PCA=y
CONFIG_ATM_FORE200E_PCA_DEFAULT_FW=y
# CONFIG_ATM_FORE200E_USE_TASKLET is not set
CONFIG_ATM_FORE200E_TX_RETRY=16
CONFIG_ATM_FORE200E_DEBUG=0
CONFIG_ATM_FORE200E=m
CONFIG_ATM_HE=m
CONFIG_ATM_HE_USE_SUNI=y
CONFIG_FDDI=y
CONFIG_DEFXX=m
# CONFIG_DEFXX_MMIO is not set
CONFIG_SKFP=m
CONFIG_HIPPI=y
CONFIG_ROADRUNNER=m
# CONFIG_ROADRUNNER_LARGE_RINGS is not set
CONFIG_PLIP=m
CONFIG_PPP=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
CONFIG_PPPOATM=m
# CONFIG_PPPOL2TP is not set
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLHC=m
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
CONFIG_NET_FC=y
CONFIG_SHAPER=m
CONFIG_NETCONSOLE=m
# CONFIG_NETCONSOLE_DYNAMIC is not set
CONFIG_NETPOLL=y
# CONFIG_NETPOLL_TRAP is not set
CONFIG_NET_POLL_CONTROLLER=y
CONFIG_VIRTIO_NET=m
CONFIG_ISDN=m
CONFIG_ISDN_I4L=m
CONFIG_ISDN_PPP=y
CONFIG_ISDN_PPP_VJ=y
CONFIG_ISDN_MPP=y
CONFIG_IPPP_FILTER=y
CONFIG_ISDN_PPP_BSDCOMP=m
CONFIG_ISDN_AUDIO=y
CONFIG_ISDN_TTY_FAX=y
CONFIG_ISDN_X25=y

#
# ISDN feature submodules
#
CONFIG_ISDN_DIVERSION=m

#
# ISDN4Linux hardware drivers
#

#
# Passive cards
#
CONFIG_ISDN_DRV_HISAX=m

#
# D-channel protocol features
#
CONFIG_HISAX_EURO=y
CONFIG_DE_AOC=y
# CONFIG_HISAX_NO_SENDCOMPLETE is not set
# CONFIG_HISAX_NO_LLC is not set
# CONFIG_HISAX_NO_KEYPAD is not set
CONFIG_HISAX_1TR6=y
CONFIG_HISAX_NI1=y
CONFIG_HISAX_MAX_CARDS=8

#
# HiSax supported cards
#
CONFIG_HISAX_16_0=y
CONFIG_HISAX_16_3=y
CONFIG_HISAX_TELESPCI=y
CONFIG_HISAX_S0BOX=y
CONFIG_HISAX_AVM_A1=y
CONFIG_HISAX_FRITZPCI=y
CONFIG_HISAX_AVM_A1_PCMCIA=y
CONFIG_HISAX_ELSA=y
CONFIG_HISAX_IX1MICROR2=y
CONFIG_HISAX_DIEHLDIVA=y
CONFIG_HISAX_ASUSCOM=y
CONFIG_HISAX_TELEINT=y
CONFIG_HISAX_HFCS=y
CONFIG_HISAX_SEDLBAUER=y
CONFIG_HISAX_SPORTSTER=y
CONFIG_HISAX_MIC=y
CONFIG_HISAX_NETJET=y
CONFIG_HISAX_NETJET_U=y
CONFIG_HISAX_NICCY=y
CONFIG_HISAX_ISURF=y
CONFIG_HISAX_HSTSAPHIR=y
CONFIG_HISAX_BKM_A4T=y
CONFIG_HISAX_SCT_QUADRO=y
CONFIG_HISAX_GAZEL=y
CONFIG_HISAX_HFC_PCI=y
CONFIG_HISAX_W6692=y
CONFIG_HISAX_HFC_SX=y
CONFIG_HISAX_ENTERNOW_PCI=y
# CONFIG_HISAX_DEBUG is not set

#
# HiSax PCMCIA card service modules
#
CONFIG_HISAX_SEDLBAUER_CS=m
CONFIG_HISAX_ELSA_CS=m
CONFIG_HISAX_AVM_A1_CS=m
CONFIG_HISAX_TELES_CS=m

#
# HiSax sub driver modules
#
CONFIG_HISAX_ST5481=m
CONFIG_HISAX_HFCUSB=m
CONFIG_HISAX_HFC4S8S=m
CONFIG_HISAX_FRITZ_PCIPNP=m
CONFIG_HISAX_HDLC=y

#
# Active cards
#
CONFIG_ISDN_DRV_ICN=m
CONFIG_ISDN_DRV_PCBIT=m
CONFIG_ISDN_DRV_SC=m
CONFIG_ISDN_DRV_ACT2000=m
CONFIG_ISDN_DRV_GIGASET=m
CONFIG_GIGASET_BASE=m
CONFIG_GIGASET_M105=m
CONFIG_GIGASET_M101=m
# CONFIG_GIGASET_DEBUG is not set
# CONFIG_GIGASET_UNDOCREQ is not set
CONFIG_ISDN_CAPI=m
CONFIG_ISDN_DRV_AVMB1_VERBOSE_REASON=y
CONFIG_CAPI_TRACE=y
CONFIG_ISDN_CAPI_MIDDLEWARE=y
CONFIG_ISDN_CAPI_CAPI20=m
CONFIG_ISDN_CAPI_CAPIFS_BOOL=y
CONFIG_ISDN_CAPI_CAPIFS=m
CONFIG_ISDN_CAPI_CAPIDRV=m

#
# CAPI hardware drivers
#
CONFIG_CAPI_AVM=y
CONFIG_ISDN_DRV_AVMB1_B1ISA=m
CONFIG_ISDN_DRV_AVMB1_B1PCI=m
CONFIG_ISDN_DRV_AVMB1_B1PCIV4=y
CONFIG_ISDN_DRV_AVMB1_T1ISA=m
CONFIG_ISDN_DRV_AVMB1_B1PCMCIA=m
CONFIG_ISDN_DRV_AVMB1_AVM_CS=m
CONFIG_ISDN_DRV_AVMB1_T1PCI=m
CONFIG_ISDN_DRV_AVMB1_C4=m
CONFIG_CAPI_EICON=y
CONFIG_ISDN_DIVAS=m
CONFIG_ISDN_DIVAS_BRIPCI=y
CONFIG_ISDN_DIVAS_PRIPCI=y
CONFIG_ISDN_DIVAS_DIVACAPI=m
CONFIG_ISDN_DIVAS_USERIDI=m
CONFIG_ISDN_DIVAS_MAINT=m
CONFIG_PHONE=m
CONFIG_PHONE_IXJ=m
CONFIG_PHONE_IXJ_PCMCIA=m

#
# Input device support
#
CONFIG_INPUT=y
CONFIG_INPUT_FF_MEMLESS=m
CONFIG_INPUT_POLLDEV=m

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=m
CONFIG_INPUT_EVDEV=m
CONFIG_INPUT_EVBUG=m

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
CONFIG_KEYBOARD_SUNKBD=m
CONFIG_KEYBOARD_LKKBD=m
CONFIG_KEYBOARD_XTKBD=m
CONFIG_KEYBOARD_NEWTON=m
CONFIG_KEYBOARD_STOWAWAY=m
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=m
CONFIG_MOUSE_PS2_ALPS=y
CONFIG_MOUSE_PS2_LOGIPS2PP=y
CONFIG_MOUSE_PS2_SYNAPTICS=y
CONFIG_MOUSE_PS2_LIFEBOOK=y
CONFIG_MOUSE_PS2_TRACKPOINT=y
# CONFIG_MOUSE_PS2_TOUCHKIT is not set
CONFIG_MOUSE_SERIAL=m
CONFIG_MOUSE_APPLETOUCH=m
CONFIG_MOUSE_INPORT=m
# CONFIG_MOUSE_ATIXL is not set
CONFIG_MOUSE_LOGIBM=m
CONFIG_MOUSE_PC110PAD=m
CONFIG_MOUSE_VSXXXAA=m
CONFIG_INPUT_JOYSTICK=y
CONFIG_JOYSTICK_ANALOG=m
CONFIG_JOYSTICK_A3D=m
CONFIG_JOYSTICK_ADI=m
CONFIG_JOYSTICK_COBRA=m
CONFIG_JOYSTICK_GF2K=m
CONFIG_JOYSTICK_GRIP=m
CONFIG_JOYSTICK_GRIP_MP=m
CONFIG_JOYSTICK_GUILLEMOT=m
CONFIG_JOYSTICK_INTERACT=m
CONFIG_JOYSTICK_SIDEWINDER=m
CONFIG_JOYSTICK_TMDC=m
CONFIG_JOYSTICK_IFORCE=m
CONFIG_JOYSTICK_IFORCE_USB=y
CONFIG_JOYSTICK_IFORCE_232=y
CONFIG_JOYSTICK_WARRIOR=m
CONFIG_JOYSTICK_MAGELLAN=m
CONFIG_JOYSTICK_SPACEORB=m
CONFIG_JOYSTICK_SPACEBALL=m
CONFIG_JOYSTICK_STINGER=m
CONFIG_JOYSTICK_TWIDJOY=m
CONFIG_JOYSTICK_DB9=m
CONFIG_JOYSTICK_GAMECON=m
CONFIG_JOYSTICK_TURBOGRAFX=m
CONFIG_JOYSTICK_JOYDUMP=m
CONFIG_JOYSTICK_XPAD=m
# CONFIG_JOYSTICK_XPAD_FF is not set
# CONFIG_JOYSTICK_XPAD_LEDS is not set
CONFIG_INPUT_TABLET=y
CONFIG_TABLET_USB_ACECAD=m
CONFIG_TABLET_USB_AIPTEK=m
CONFIG_TABLET_USB_GTCO=m
CONFIG_TABLET_USB_KBTAB=m
CONFIG_TABLET_USB_WACOM=m
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_ADS7846=m
CONFIG_TOUCHSCREEN_FUJITSU=m
CONFIG_TOUCHSCREEN_GUNZE=m
CONFIG_TOUCHSCREEN_ELO=m
CONFIG_TOUCHSCREEN_MTOUCH=m
CONFIG_TOUCHSCREEN_MK712=m
CONFIG_TOUCHSCREEN_PENMOUNT=m
CONFIG_TOUCHSCREEN_TOUCHRIGHT=m
CONFIG_TOUCHSCREEN_TOUCHWIN=m
CONFIG_TOUCHSCREEN_UCB1400=m
CONFIG_TOUCHSCREEN_USB_COMPOSITE=m
CONFIG_TOUCHSCREEN_USB_EGALAX=y
CONFIG_TOUCHSCREEN_USB_PANJIT=y
CONFIG_TOUCHSCREEN_USB_3M=y
CONFIG_TOUCHSCREEN_USB_ITM=y
CONFIG_TOUCHSCREEN_USB_ETURBO=y
CONFIG_TOUCHSCREEN_USB_GUNZE=y
CONFIG_TOUCHSCREEN_USB_DMC_TSC10=y
CONFIG_TOUCHSCREEN_USB_IRTOUCH=y
CONFIG_TOUCHSCREEN_USB_IDEALTEK=y
CONFIG_TOUCHSCREEN_USB_GENERAL_TOUCH=y
CONFIG_TOUCHSCREEN_USB_GOTOP=y
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=m
CONFIG_INPUT_WISTRON_BTNS=m
CONFIG_INPUT_ATLAS_BTNS=m
CONFIG_INPUT_ATI_REMOTE=m
CONFIG_INPUT_ATI_REMOTE2=m
CONFIG_INPUT_KEYSPAN_REMOTE=m
CONFIG_INPUT_POWERMATE=m
CONFIG_INPUT_YEALINK=m
CONFIG_INPUT_UINPUT=m

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=m
CONFIG_SERIO_CT82C710=m
CONFIG_SERIO_PARKBD=m
CONFIG_SERIO_PCIPS2=m
CONFIG_SERIO_LIBPS2=y
CONFIG_SERIO_RAW=m
CONFIG_GAMEPORT=m
CONFIG_GAMEPORT_NS558=m
CONFIG_GAMEPORT_L4=m
CONFIG_GAMEPORT_EMU10K1=m
CONFIG_GAMEPORT_FM801=m

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
CONFIG_SERIAL_NONSTANDARD=y
# CONFIG_COMPUTONE is not set
CONFIG_ROCKETPORT=m
CONFIG_CYCLADES=m
# CONFIG_CYZ_INTR is not set
CONFIG_DIGIEPCA=m
# CONFIG_ESPSERIAL is not set
# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
CONFIG_MOXA_SMARTIO_NEW=m
# CONFIG_ISI is not set
CONFIG_SYNCLINK=m
CONFIG_SYNCLINKMP=m
CONFIG_SYNCLINK_GT=m
CONFIG_N_HDLC=m
CONFIG_SPECIALIX=m
# CONFIG_SPECIALIX_RTSCTS is not set
CONFIG_SX=m
# CONFIG_RIO is not set
CONFIG_STALDRV=y

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_FIX_EARLYCON_MEM=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_PNP=y
CONFIG_SERIAL_8250_CS=m
CONFIG_SERIAL_8250_NR_UARTS=48
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_FOURPORT=m
CONFIG_SERIAL_8250_ACCENT=m
CONFIG_SERIAL_8250_BOCA=m
CONFIG_SERIAL_8250_EXAR_ST16C554=m
CONFIG_SERIAL_8250_HUB6=m
CONFIG_SERIAL_8250_SHARE_IRQ=y
# CONFIG_SERIAL_8250_DETECT_IRQ is not set
CONFIG_SERIAL_8250_RSA=y
CONFIG_SERIAL_8250_MCA=m

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_JSM=m
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
CONFIG_PRINTER=m
# CONFIG_LP_CONSOLE is not set
CONFIG_PPDEV=m
CONFIG_TIPAR=m
CONFIG_HVC_DRIVER=y
CONFIG_VIRTIO_CONSOLE=y
CONFIG_IPMI_HANDLER=m
# CONFIG_IPMI_PANIC_EVENT is not set
CONFIG_IPMI_DEVICE_INTERFACE=m
CONFIG_IPMI_SI=m
CONFIG_IPMI_WATCHDOG=m
CONFIG_IPMI_POWEROFF=m
CONFIG_HW_RANDOM=y
CONFIG_HW_RANDOM_INTEL=m
CONFIG_HW_RANDOM_AMD=m
CONFIG_HW_RANDOM_GEODE=m
CONFIG_HW_RANDOM_VIA=m
CONFIG_NVRAM=m
CONFIG_RTC=y
CONFIG_DTLK=m
CONFIG_R3964=m
CONFIG_APPLICOM=m
CONFIG_SONYPI=m

#
# PCMCIA character devices
#
CONFIG_SYNCLINK_CS=m
CONFIG_CARDMAN_4000=m
CONFIG_CARDMAN_4040=m
CONFIG_MWAVE=m
CONFIG_SCx200_GPIO=m
CONFIG_PC8736x_GPIO=m
CONFIG_NSC_GPIO=m
CONFIG_CS5535_GPIO=m
CONFIG_RAW_DRIVER=m
CONFIG_MAX_RAW_DEVS=256
CONFIG_HPET=y
# CONFIG_HPET_RTC_IRQ is not set
CONFIG_HPET_MMAP=y
CONFIG_HANGCHECK_TIMER=m
CONFIG_TCG_TPM=m
CONFIG_TCG_TIS=m
CONFIG_TCG_NSC=m
CONFIG_TCG_ATMEL=m
CONFIG_TCG_INFINEON=m
CONFIG_TELCLOCK=m
CONFIG_DEVPORT=y
CONFIG_I2C=m
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=m

#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=m
CONFIG_I2C_ALGOPCF=m
CONFIG_I2C_ALGOPCA=m

#
# I2C Hardware Bus support
#
CONFIG_I2C_ALI1535=m
CONFIG_I2C_ALI1563=m
CONFIG_I2C_ALI15X3=m
CONFIG_I2C_AMD756=m
CONFIG_I2C_AMD756_S4882=m
CONFIG_I2C_AMD8111=m
CONFIG_I2C_I801=m
CONFIG_I2C_I810=m
CONFIG_I2C_PIIX4=m
CONFIG_I2C_NFORCE2=m
CONFIG_I2C_OCORES=m
CONFIG_I2C_PARPORT=m
CONFIG_I2C_PARPORT_LIGHT=m
CONFIG_I2C_PROSAVAGE=m
CONFIG_I2C_SAVAGE4=m
CONFIG_I2C_SIMTEC=m
CONFIG_SCx200_I2C=m
CONFIG_SCx200_I2C_SCL=12
CONFIG_SCx200_I2C_SDA=13
CONFIG_SCx200_ACB=m
CONFIG_I2C_SIS5595=m
CONFIG_I2C_SIS630=m
CONFIG_I2C_SIS96X=m
# CONFIG_I2C_TAOS_EVM is not set
CONFIG_I2C_STUB=m
CONFIG_I2C_TINY_USB=m
CONFIG_I2C_VIA=m
CONFIG_I2C_VIAPRO=m
CONFIG_I2C_VOODOO3=m
CONFIG_I2C_PCA_ISA=m

#
# Miscellaneous I2C Chip support
#
CONFIG_SENSORS_DS1337=m
CONFIG_SENSORS_DS1374=m
# CONFIG_DS1682 is not set
CONFIG_SENSORS_EEPROM=m
CONFIG_SENSORS_PCF8574=m
CONFIG_SENSORS_PCA9539=m
CONFIG_SENSORS_PCF8591=m
CONFIG_SENSORS_MAX6875=m
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set

#
# SPI support
#
CONFIG_SPI=y
# CONFIG_SPI_DEBUG is not set
CONFIG_SPI_MASTER=y

#
# SPI Master Controller Drivers
#
CONFIG_SPI_BITBANG=m
CONFIG_SPI_BUTTERFLY=m
# CONFIG_SPI_LM70_LLP is not set

#
# SPI Protocol Masters
#
CONFIG_SPI_AT25=m
CONFIG_SPI_SPIDEV=m
# CONFIG_SPI_TLE62X0 is not set
CONFIG_W1=m
CONFIG_W1_CON=y

#
# 1-wire Bus Masters
#
CONFIG_W1_MASTER_MATROX=m
CONFIG_W1_MASTER_DS2490=m
CONFIG_W1_MASTER_DS2482=m

#
# 1-wire Slaves
#
CONFIG_W1_SLAVE_THERM=m
CONFIG_W1_SLAVE_SMEM=m
CONFIG_W1_SLAVE_DS2433=m
# CONFIG_W1_SLAVE_DS2433_CRC is not set
# CONFIG_W1_SLAVE_DS2760 is not set
CONFIG_POWER_SUPPLY=m
# CONFIG_POWER_SUPPLY_DEBUG is not set
# CONFIG_PDA_POWER is not set
# CONFIG_BATTERY_DS2760 is not set
CONFIG_HWMON=y
CONFIG_HWMON_VID=m
CONFIG_SENSORS_ABITUGURU=m
# CONFIG_SENSORS_ABITUGURU3 is not set
CONFIG_SENSORS_AD7418=m
CONFIG_SENSORS_ADM1021=m
CONFIG_SENSORS_ADM1025=m
CONFIG_SENSORS_ADM1026=m
CONFIG_SENSORS_ADM1029=m
CONFIG_SENSORS_ADM1031=m
CONFIG_SENSORS_ADM9240=m
CONFIG_SENSORS_ADT7470=m
CONFIG_SENSORS_K8TEMP=m
CONFIG_SENSORS_ASB100=m
CONFIG_SENSORS_ATXP1=m
CONFIG_SENSORS_DS1621=m
CONFIG_SENSORS_I5K_AMB=m
CONFIG_SENSORS_F71805F=m
CONFIG_SENSORS_F71882FG=m
# CONFIG_SENSORS_F75375S is not set
CONFIG_SENSORS_FSCHER=m
CONFIG_SENSORS_FSCPOS=m
# CONFIG_SENSORS_FSCHMD is not set
CONFIG_SENSORS_GL518SM=m
CONFIG_SENSORS_GL520SM=m
CONFIG_SENSORS_CORETEMP=m
# CONFIG_SENSORS_IBMPEX is not set
CONFIG_SENSORS_IT87=m
CONFIG_SENSORS_LM63=m
CONFIG_SENSORS_LM70=m
CONFIG_SENSORS_LM75=m
CONFIG_SENSORS_LM77=m
CONFIG_SENSORS_LM78=m
CONFIG_SENSORS_LM80=m
CONFIG_SENSORS_LM83=m
CONFIG_SENSORS_LM85=m
CONFIG_SENSORS_LM87=m
CONFIG_SENSORS_LM90=m
CONFIG_SENSORS_LM92=m
# CONFIG_SENSORS_LM93 is not set
CONFIG_SENSORS_MAX1619=m
CONFIG_SENSORS_MAX6650=m
CONFIG_SENSORS_PC87360=m
CONFIG_SENSORS_PC87427=m
CONFIG_SENSORS_SIS5595=m
# CONFIG_SENSORS_DME1737 is not set
CONFIG_SENSORS_SMSC47M1=m
CONFIG_SENSORS_SMSC47M192=m
CONFIG_SENSORS_SMSC47B397=m
# CONFIG_SENSORS_THMC50 is not set
CONFIG_SENSORS_VIA686A=m
CONFIG_SENSORS_VT1211=m
CONFIG_SENSORS_VT8231=m
CONFIG_SENSORS_W83781D=m
CONFIG_SENSORS_W83791D=m
CONFIG_SENSORS_W83792D=m
CONFIG_SENSORS_W83793=m
CONFIG_SENSORS_W83L785TS=m
CONFIG_SENSORS_W83627HF=m
CONFIG_SENSORS_W83627EHF=m
CONFIG_SENSORS_HDAPS=m
CONFIG_SENSORS_APPLESMC=m
# CONFIG_HWMON_DEBUG_CHIP is not set
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set

#
# Watchdog Device Drivers
#
CONFIG_SOFT_WATCHDOG=m
CONFIG_ACQUIRE_WDT=m
CONFIG_ADVANTECH_WDT=m
CONFIG_ALIM1535_WDT=m
CONFIG_ALIM7101_WDT=m
CONFIG_SC520_WDT=m
CONFIG_EUROTECH_WDT=m
CONFIG_IB700_WDT=m
CONFIG_IBMASR=m
CONFIG_WAFER_WDT=m
CONFIG_I6300ESB_WDT=m
CONFIG_ITCO_WDT=m
CONFIG_ITCO_VENDOR_SUPPORT=y
CONFIG_SC1200_WDT=m
CONFIG_SCx200_WDT=m
CONFIG_PC87413_WDT=m
CONFIG_60XX_WDT=m
CONFIG_SBC8360_WDT=m
CONFIG_CPU5_WDT=m
CONFIG_SMSC37B787_WDT=m
CONFIG_W83627HF_WDT=m
CONFIG_W83697HF_WDT=m
CONFIG_W83877F_WDT=m
CONFIG_W83977F_WDT=m
CONFIG_MACHZ_WDT=m
CONFIG_SBC_EPX_C3_WATCHDOG=m

#
# ISA-based Watchdog Cards
#
CONFIG_PCWATCHDOG=m
CONFIG_MIXCOMWD=m
CONFIG_WDT=m
CONFIG_WDT_501=y

#
# PCI-based Watchdog Cards
#
CONFIG_PCIPCWATCHDOG=m
CONFIG_WDTPCI=m
CONFIG_WDT_501_PCI=y

#
# USB-based Watchdog Cards
#
CONFIG_USBPCWATCHDOG=m

#
# Sonics Silicon Backplane
#
CONFIG_SSB_POSSIBLE=y
CONFIG_SSB=m
CONFIG_SSB_PCIHOST_POSSIBLE=y
CONFIG_SSB_PCIHOST=y
CONFIG_SSB_PCMCIAHOST_POSSIBLE=y
# CONFIG_SSB_PCMCIAHOST is not set
# CONFIG_SSB_SILENT is not set
# CONFIG_SSB_DEBUG is not set
CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
CONFIG_SSB_DRIVER_PCICORE=y

#
# Multifunction device drivers
#
CONFIG_MFD_SM501=m

#
# Multimedia devices
#
CONFIG_VIDEO_DEV=m
CONFIG_VIDEO_V4L1=y
CONFIG_VIDEO_V4L1_COMPAT=y
CONFIG_VIDEO_V4L2=y
CONFIG_VIDEO_CAPTURE_DRIVERS=y
# CONFIG_VIDEO_ADV_DEBUG is not set
# CONFIG_VIDEO_HELPER_CHIPS_AUTO is not set

#
# Encoders/decoders and other helper chips
#

#
# Audio decoders
#
CONFIG_VIDEO_TVAUDIO=m
CONFIG_VIDEO_TDA7432=m
CONFIG_VIDEO_TDA9840=m
CONFIG_VIDEO_TDA9875=m
CONFIG_VIDEO_TEA6415C=m
CONFIG_VIDEO_TEA6420=m
CONFIG_VIDEO_MSP3400=m
CONFIG_VIDEO_CS53L32A=m
CONFIG_VIDEO_TLV320AIC23B=m
CONFIG_VIDEO_WM8775=m
CONFIG_VIDEO_WM8739=m
CONFIG_VIDEO_VP27SMPX=m

#
# Video decoders
#
CONFIG_VIDEO_BT819=m
CONFIG_VIDEO_BT856=m
CONFIG_VIDEO_BT866=m
CONFIG_VIDEO_KS0127=m
CONFIG_VIDEO_OV7670=m
# CONFIG_VIDEO_TCM825X is not set
CONFIG_VIDEO_SAA7110=m
CONFIG_VIDEO_SAA7111=m
CONFIG_VIDEO_SAA7114=m
CONFIG_VIDEO_SAA711X=m
CONFIG_VIDEO_SAA7191=m
CONFIG_VIDEO_TVP5150=m
CONFIG_VIDEO_VPX3220=m

#
# Video and audio decoders
#
CONFIG_VIDEO_CX25840=m

#
# MPEG video encoders
#
CONFIG_VIDEO_CX2341X=m

#
# Video encoders
#
CONFIG_VIDEO_SAA7127=m
CONFIG_VIDEO_SAA7185=m
CONFIG_VIDEO_ADV7170=m
CONFIG_VIDEO_ADV7175=m

#
# Video improvement chips
#
CONFIG_VIDEO_UPD64031A=m
CONFIG_VIDEO_UPD64083=m
CONFIG_VIDEO_VIVI=m
CONFIG_VIDEO_BT848=m
CONFIG_VIDEO_BT848_DVB=y
CONFIG_VIDEO_SAA6588=m
CONFIG_VIDEO_PMS=m
CONFIG_VIDEO_BWQCAM=m
CONFIG_VIDEO_CQCAM=m
CONFIG_VIDEO_W9966=m
CONFIG_VIDEO_CPIA=m
CONFIG_VIDEO_CPIA_PP=m
CONFIG_VIDEO_CPIA_USB=m
CONFIG_VIDEO_CPIA2=m
CONFIG_VIDEO_SAA5246A=m
CONFIG_VIDEO_SAA5249=m
CONFIG_TUNER_3036=m
CONFIG_VIDEO_STRADIS=m
CONFIG_VIDEO_ZORAN_ZR36060=m
CONFIG_VIDEO_ZORAN=m
CONFIG_VIDEO_ZORAN_BUZ=m
CONFIG_VIDEO_ZORAN_DC10=m
CONFIG_VIDEO_ZORAN_DC30=m
CONFIG_VIDEO_ZORAN_LML33=m
CONFIG_VIDEO_ZORAN_LML33R10=m
CONFIG_VIDEO_ZORAN_AVS6EYES=m
CONFIG_VIDEO_MEYE=m
CONFIG_VIDEO_SAA7134=m
CONFIG_VIDEO_SAA7134_ALSA=m
CONFIG_VIDEO_SAA7134_OSS=m
CONFIG_VIDEO_SAA7134_DVB=m
# CONFIG_VIDEO_MXB is not set
# CONFIG_VIDEO_DPC is not set
CONFIG_VIDEO_HEXIUM_ORION=m
CONFIG_VIDEO_HEXIUM_GEMINI=m
CONFIG_VIDEO_CX88=m
CONFIG_VIDEO_CX88_ALSA=m
CONFIG_VIDEO_CX88_BLACKBIRD=m
CONFIG_VIDEO_CX88_DVB=m
CONFIG_VIDEO_CX88_VP3054=m
# CONFIG_VIDEO_CX23885 is not set
CONFIG_VIDEO_IVTV=m
# CONFIG_VIDEO_FB_IVTV is not set
CONFIG_VIDEO_CAFE_CCIC=m
CONFIG_V4L_USB_DRIVERS=y
CONFIG_VIDEO_PVRUSB2=m
CONFIG_VIDEO_PVRUSB2_29XXX=y
CONFIG_VIDEO_PVRUSB2_24XXX=y
CONFIG_VIDEO_PVRUSB2_SYSFS=y
# CONFIG_VIDEO_PVRUSB2_DEBUGIFC is not set
CONFIG_VIDEO_EM28XX=m
CONFIG_VIDEO_USBVISION=m
CONFIG_VIDEO_USBVIDEO=m
CONFIG_USB_VICAM=m
CONFIG_USB_IBMCAM=m
CONFIG_USB_KONICAWC=m
CONFIG_USB_QUICKCAM_MESSENGER=m
CONFIG_USB_ET61X251=m
CONFIG_VIDEO_OVCAMCHIP=m
CONFIG_USB_W9968CF=m
# CONFIG_USB_OV511 is not set
CONFIG_USB_SE401=m
CONFIG_USB_SN9C102=m
CONFIG_USB_STV680=m
CONFIG_USB_ZC0301=m
CONFIG_USB_PWC=m
# CONFIG_USB_PWC_DEBUG is not set
CONFIG_USB_ZR364XX=m
CONFIG_RADIO_ADAPTERS=y
CONFIG_RADIO_CADET=m
CONFIG_RADIO_RTRACK=m
CONFIG_RADIO_RTRACK2=m
CONFIG_RADIO_AZTECH=m
CONFIG_RADIO_GEMTEK=m
CONFIG_RADIO_GEMTEK_PCI=m
CONFIG_RADIO_MAXIRADIO=m
CONFIG_RADIO_MAESTRO=m
CONFIG_RADIO_SF16FMI=m
CONFIG_RADIO_SF16FMR2=m
CONFIG_RADIO_TERRATEC=m
CONFIG_RADIO_TRUST=m
CONFIG_RADIO_TYPHOON=m
# CONFIG_RADIO_TYPHOON_PROC_FS is not set
CONFIG_RADIO_ZOLTRIX=m
CONFIG_USB_DSBR=m
CONFIG_DVB_CORE=m
CONFIG_DVB_CORE_ATTACH=y
CONFIG_DVB_CAPTURE_DRIVERS=y

#
# Supported SAA7146 based PCI Adapters
#
CONFIG_DVB_AV7110=m
CONFIG_DVB_AV7110_OSD=y
CONFIG_DVB_BUDGET=m
CONFIG_DVB_BUDGET_CI=m
CONFIG_DVB_BUDGET_AV=m
CONFIG_DVB_BUDGET_PATCH=m

#
# Supported USB Adapters
#
CONFIG_DVB_USB=m
# CONFIG_DVB_USB_DEBUG is not set
CONFIG_DVB_USB_A800=m
CONFIG_DVB_USB_DIBUSB_MB=m
CONFIG_DVB_USB_DIBUSB_MB_FAULTY=y
CONFIG_DVB_USB_DIBUSB_MC=m
CONFIG_DVB_USB_DIB0700=m
CONFIG_DVB_USB_UMT_010=m
CONFIG_DVB_USB_CXUSB=m
CONFIG_DVB_USB_M920X=m
CONFIG_DVB_USB_GL861=m
CONFIG_DVB_USB_AU6610=m
CONFIG_DVB_USB_DIGITV=m
CONFIG_DVB_USB_VP7045=m
CONFIG_DVB_USB_VP702X=m
CONFIG_DVB_USB_GP8PSK=m
CONFIG_DVB_USB_NOVA_T_USB2=m
CONFIG_DVB_USB_TTUSB2=m
CONFIG_DVB_USB_DTT200U=m
CONFIG_DVB_USB_OPERA1=m
# CONFIG_DVB_USB_AF9005 is not set
CONFIG_DVB_TTUSB_BUDGET=m
CONFIG_DVB_TTUSB_DEC=m
CONFIG_DVB_CINERGYT2=m
CONFIG_DVB_CINERGYT2_TUNING=y
CONFIG_DVB_CINERGYT2_STREAM_URB_COUNT=32
CONFIG_DVB_CINERGYT2_STREAM_BUF_SIZE=512
CONFIG_DVB_CINERGYT2_QUERY_INTERVAL=250
CONFIG_DVB_CINERGYT2_ENABLE_RC_INPUT_DEVICE=y
CONFIG_DVB_CINERGYT2_RC_QUERY_INTERVAL=100

#
# Supported FlexCopII (B2C2) Adapters
#
CONFIG_DVB_B2C2_FLEXCOP=m
CONFIG_DVB_B2C2_FLEXCOP_PCI=m
CONFIG_DVB_B2C2_FLEXCOP_USB=m
# CONFIG_DVB_B2C2_FLEXCOP_DEBUG is not set

#
# Supported BT878 Adapters
#
CONFIG_DVB_BT8XX=m

#
# Supported Pluto2 Adapters
#
CONFIG_DVB_PLUTO2=m

#
# Supported DVB Frontends
#

#
# Customise DVB Frontends
#
# CONFIG_DVB_FE_CUSTOMISE is not set

#
# DVB-S (satellite) frontends
#
CONFIG_DVB_STV0299=m
CONFIG_DVB_CX24110=m
CONFIG_DVB_CX24123=m
CONFIG_DVB_TDA8083=m
CONFIG_DVB_MT312=m
CONFIG_DVB_VES1X93=m
CONFIG_DVB_S5H1420=m
CONFIG_DVB_TDA10086=m

#
# DVB-T (terrestrial) frontends
#
CONFIG_DVB_SP8870=m
CONFIG_DVB_SP887X=m
CONFIG_DVB_CX22700=m
CONFIG_DVB_CX22702=m
CONFIG_DVB_L64781=m
CONFIG_DVB_TDA1004X=m
CONFIG_DVB_NXT6000=m
CONFIG_DVB_MT352=m
CONFIG_DVB_ZL10353=m
CONFIG_DVB_DIB3000MB=m
CONFIG_DVB_DIB3000MC=m
CONFIG_DVB_DIB7000M=m
CONFIG_DVB_DIB7000P=m

#
# DVB-C (cable) frontends
#
CONFIG_DVB_VES1820=m
CONFIG_DVB_TDA10021=m
CONFIG_DVB_TDA10023=m
CONFIG_DVB_STV0297=m

#
# ATSC (North American/Korean Terrestrial/Cable DTV) frontends
#
CONFIG_DVB_NXT200X=m
CONFIG_DVB_OR51211=m
CONFIG_DVB_OR51132=m
CONFIG_DVB_BCM3510=m
CONFIG_DVB_LGDT330X=m
# CONFIG_DVB_S5H1409 is not set

#
# Tuners/PLL support
#
CONFIG_DVB_PLL=m
CONFIG_DVB_TDA826X=m
CONFIG_DVB_TDA827X=m
CONFIG_DVB_TUNER_QT1010=m
CONFIG_DVB_TUNER_MT2060=m
CONFIG_DVB_TUNER_MT2266=m
# CONFIG_DVB_TUNER_MT2131 is not set
CONFIG_DVB_TUNER_DIB0070=m

#
# Miscellaneous devices
#
CONFIG_DVB_LNBP21=m
CONFIG_DVB_ISL6421=m
CONFIG_DVB_TUA6100=m
CONFIG_VIDEO_SAA7146=m
CONFIG_VIDEO_SAA7146_VV=m
CONFIG_VIDEO_TUNER=m
# CONFIG_VIDEO_TUNER_CUSTOMIZE is not set
CONFIG_TUNER_MT20XX=m
CONFIG_TUNER_TDA8290=m
CONFIG_TUNER_TEA5761=m
CONFIG_TUNER_TEA5767=m
CONFIG_TUNER_SIMPLE=m
CONFIG_VIDEOBUF_GEN=m
CONFIG_VIDEOBUF_DMA_SG=m
CONFIG_VIDEOBUF_VMALLOC=m
CONFIG_VIDEOBUF_DVB=m
CONFIG_VIDEO_BTCX=m
CONFIG_VIDEO_IR_I2C=m
CONFIG_VIDEO_IR=m
CONFIG_VIDEO_TVEEPROM=m
CONFIG_DAB=y
CONFIG_USB_DABUSB=m

#
# Graphics support
#
CONFIG_AGP=m
CONFIG_AGP_ALI=m
CONFIG_AGP_ATI=m
CONFIG_AGP_AMD=m
CONFIG_AGP_AMD64=m
CONFIG_AGP_INTEL=m
CONFIG_AGP_NVIDIA=m
CONFIG_AGP_SIS=m
CONFIG_AGP_SWORKS=m
CONFIG_AGP_VIA=m
CONFIG_AGP_EFFICEON=m
CONFIG_DRM=m
CONFIG_DRM_TDFX=m
CONFIG_DRM_R128=m
CONFIG_DRM_RADEON=m
CONFIG_DRM_I810=m
CONFIG_DRM_I830=m
CONFIG_DRM_I915=m
CONFIG_DRM_MGA=m
CONFIG_DRM_SIS=m
CONFIG_DRM_VIA=m
CONFIG_DRM_SAVAGE=m
CONFIG_VGASTATE=m
CONFIG_VIDEO_OUTPUT_CONTROL=m
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
CONFIG_FB_DDC=m
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
CONFIG_FB_SYS_FILLRECT=m
CONFIG_FB_SYS_COPYAREA=m
CONFIG_FB_SYS_IMAGEBLIT=m
CONFIG_FB_SYS_FOPS=m
CONFIG_FB_DEFERRED_IO=y
CONFIG_FB_SVGALIB=m
# CONFIG_FB_MACMODES is not set
CONFIG_FB_BACKLIGHT=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y

#
# Frame buffer hardware drivers
#
CONFIG_FB_CIRRUS=m
CONFIG_FB_PM2=m
CONFIG_FB_PM2_FIFO_DISCONNECT=y
CONFIG_FB_CYBER2000=m
# CONFIG_FB_ARC is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
CONFIG_FB_VGA16=m
CONFIG_FB_UVESA=m
CONFIG_FB_VESA=y
# CONFIG_FB_EFI is not set
CONFIG_FB_IMAC=y
CONFIG_FB_HECUBA=m
CONFIG_FB_HGA=m
# CONFIG_FB_HGA_ACCEL is not set
CONFIG_FB_S1D13XXX=m
CONFIG_FB_NVIDIA=m
CONFIG_FB_NVIDIA_I2C=y
# CONFIG_FB_NVIDIA_DEBUG is not set
CONFIG_FB_NVIDIA_BACKLIGHT=y
CONFIG_FB_RIVA=m
CONFIG_FB_RIVA_I2C=y
# CONFIG_FB_RIVA_DEBUG is not set
CONFIG_FB_RIVA_BACKLIGHT=y
CONFIG_FB_I810=m
# CONFIG_FB_I810_GTF is not set
CONFIG_FB_LE80578=m
CONFIG_FB_CARILLO_RANCH=m
CONFIG_FB_INTEL=m
# CONFIG_FB_INTEL_DEBUG is not set
CONFIG_FB_INTEL_I2C=y
CONFIG_FB_MATROX=m
CONFIG_FB_MATROX_MILLENIUM=y
CONFIG_FB_MATROX_MYSTIQUE=y
CONFIG_FB_MATROX_G=y
CONFIG_FB_MATROX_I2C=m
CONFIG_FB_MATROX_MAVEN=m
CONFIG_FB_MATROX_MULTIHEAD=y
CONFIG_FB_RADEON=m
CONFIG_FB_RADEON_I2C=y
CONFIG_FB_RADEON_BACKLIGHT=y
# CONFIG_FB_RADEON_DEBUG is not set
CONFIG_FB_ATY128=m
CONFIG_FB_ATY128_BACKLIGHT=y
CONFIG_FB_ATY=m
CONFIG_FB_ATY_CT=y
CONFIG_FB_ATY_GENERIC_LCD=y
CONFIG_FB_ATY_GX=y
CONFIG_FB_ATY_BACKLIGHT=y
CONFIG_FB_S3=m
CONFIG_FB_SAVAGE=m
CONFIG_FB_SAVAGE_I2C=y
CONFIG_FB_SAVAGE_ACCEL=y
CONFIG_FB_SIS=m
CONFIG_FB_SIS_300=y
CONFIG_FB_SIS_315=y
CONFIG_FB_NEOMAGIC=m
CONFIG_FB_KYRO=m
CONFIG_FB_3DFX=m
# CONFIG_FB_3DFX_ACCEL is not set
CONFIG_FB_VOODOO1=m
CONFIG_FB_VT8623=m
CONFIG_FB_CYBLA=m
CONFIG_FB_TRIDENT=m
# CONFIG_FB_TRIDENT_ACCEL is not set
CONFIG_FB_ARK=m
CONFIG_FB_PM3=m
CONFIG_FB_GEODE=y
# CONFIG_FB_GEODE_LX is not set
CONFIG_FB_GEODE_GX=m
# CONFIG_FB_GEODE_GX_SET_FBSIZE is not set
CONFIG_FB_GEODE_GX1=m
CONFIG_FB_SM501=m
# CONFIG_FB_VIRTUAL is not set
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=m
# CONFIG_LCD_LTV350QV is not set
CONFIG_BACKLIGHT_CLASS_DEVICE=y
# CONFIG_BACKLIGHT_CORGI is not set
CONFIG_BACKLIGHT_PROGEAR=m
CONFIG_BACKLIGHT_CARILLO_RANCH=m

#
# Display device support
#
CONFIG_DISPLAY_SUPPORT=m

#
# Display hardware drivers
#

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_VGACON_SOFT_SCROLLBACK is not set
CONFIG_VIDEO_SELECT=y
CONFIG_MDA_CONSOLE=m
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=m
# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
# CONFIG_LOGO is not set

#
# Sound
#
CONFIG_SOUND=m

#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_PCM_OSS_PLUGINS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=m
CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
CONFIG_SND_DYNAMIC_MINORS=y
CONFIG_SND_SUPPORT_OLD_API=y
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set

#
# Generic devices
#
CONFIG_SND_MPU401_UART=m
CONFIG_SND_OPL3_LIB=m
CONFIG_SND_OPL4_LIB=m
CONFIG_SND_VX_LIB=m
CONFIG_SND_AC97_CODEC=m
CONFIG_SND_DUMMY=m
CONFIG_SND_VIRMIDI=m
CONFIG_SND_MTPAV=m
CONFIG_SND_MTS64=m
CONFIG_SND_SERIAL_U16550=m
CONFIG_SND_MPU401=m
CONFIG_SND_PORTMAN2X4=m
CONFIG_SND_AD1848_LIB=m
CONFIG_SND_CS4231_LIB=m
CONFIG_SND_SB_COMMON=m
CONFIG_SND_SB8_DSP=m
CONFIG_SND_SB16_DSP=m

#
# ISA devices
#
CONFIG_SND_ADLIB=m
CONFIG_SND_AD1816A=m
CONFIG_SND_AD1848=m
CONFIG_SND_ALS100=m
CONFIG_SND_AZT2320=m
CONFIG_SND_CMI8330=m
CONFIG_SND_CS4231=m
CONFIG_SND_CS4232=m
CONFIG_SND_CS4236=m
CONFIG_SND_DT019X=m
CONFIG_SND_ES968=m
CONFIG_SND_ES1688=m
CONFIG_SND_ES18XX=m
# CONFIG_SND_SC6000 is not set
CONFIG_SND_GUS_SYNTH=m
CONFIG_SND_GUSCLASSIC=m
CONFIG_SND_GUSEXTREME=m
CONFIG_SND_GUSMAX=m
CONFIG_SND_INTERWAVE=m
CONFIG_SND_INTERWAVE_STB=m
CONFIG_SND_OPL3SA2=m
CONFIG_SND_OPTI92X_AD1848=m
CONFIG_SND_OPTI92X_CS4231=m
CONFIG_SND_OPTI93X=m
CONFIG_SND_MIRO=m
CONFIG_SND_SB8=m
CONFIG_SND_SB16=m
CONFIG_SND_SBAWE=m
CONFIG_SND_SB16_CSP=y
CONFIG_SND_SB16_CSP_FIRMWARE_IN_KERNEL=y
CONFIG_SND_SGALAXY=m
CONFIG_SND_SSCAPE=m
CONFIG_SND_WAVEFRONT=m
CONFIG_SND_WAVEFRONT_FIRMWARE_IN_KERNEL=y

#
# PCI devices
#
CONFIG_SND_AD1889=m
CONFIG_SND_ALS300=m
CONFIG_SND_ALS4000=m
CONFIG_SND_ALI5451=m
CONFIG_SND_ATIIXP=m
CONFIG_SND_ATIIXP_MODEM=m
CONFIG_SND_AU8810=m
CONFIG_SND_AU8820=m
CONFIG_SND_AU8830=m
CONFIG_SND_AZT3328=m
CONFIG_SND_BT87X=m
# CONFIG_SND_BT87X_OVERCLOCK is not set
CONFIG_SND_CA0106=m
CONFIG_SND_CMIPCI=m
CONFIG_SND_CS4281=m
CONFIG_SND_CS46XX=m
CONFIG_SND_CS46XX_NEW_DSP=y
# CONFIG_SND_CS5530 is not set
CONFIG_SND_CS5535AUDIO=m
CONFIG_SND_DARLA20=m
CONFIG_SND_GINA20=m
CONFIG_SND_LAYLA20=m
CONFIG_SND_DARLA24=m
CONFIG_SND_GINA24=m
CONFIG_SND_LAYLA24=m
CONFIG_SND_MONA=m
CONFIG_SND_MIA=m
CONFIG_SND_ECHO3G=m
CONFIG_SND_INDIGO=m
CONFIG_SND_INDIGOIO=m
CONFIG_SND_INDIGODJ=m
CONFIG_SND_EMU10K1=m
CONFIG_SND_EMU10K1X=m
CONFIG_SND_ENS1370=m
CONFIG_SND_ENS1371=m
CONFIG_SND_ES1938=m
CONFIG_SND_ES1968=m
CONFIG_SND_FM801=m
CONFIG_SND_FM801_TEA575X_BOOL=y
CONFIG_SND_FM801_TEA575X=m
# CONFIG_SND_HDA_INTEL is not set
CONFIG_SND_HDSP=m
CONFIG_SND_HDSPM=m
CONFIG_SND_ICE1712=m
CONFIG_SND_ICE1724=m
CONFIG_SND_INTEL8X0=m
CONFIG_SND_INTEL8X0M=m
CONFIG_SND_KORG1212=m
CONFIG_SND_KORG1212_FIRMWARE_IN_KERNEL=y
CONFIG_SND_MAESTRO3=m
CONFIG_SND_MAESTRO3_FIRMWARE_IN_KERNEL=y
CONFIG_SND_MIXART=m
CONFIG_SND_NM256=m
CONFIG_SND_PCXHR=m
CONFIG_SND_RIPTIDE=m
CONFIG_SND_RME32=m
CONFIG_SND_RME96=m
CONFIG_SND_RME9652=m
CONFIG_SND_SONICVIBES=m
CONFIG_SND_TRIDENT=m
CONFIG_SND_VIA82XX=m
CONFIG_SND_VIA82XX_MODEM=m
CONFIG_SND_VX222=m
CONFIG_SND_YMFPCI=m
CONFIG_SND_YMFPCI_FIRMWARE_IN_KERNEL=y
CONFIG_SND_AC97_POWER_SAVE=y
CONFIG_SND_AC97_POWER_SAVE_DEFAULT=0

#
# SPI devices
#

#
# USB devices
#
CONFIG_SND_USB_AUDIO=m
CONFIG_SND_USB_USX2Y=m
CONFIG_SND_USB_CAIAQ=m
CONFIG_SND_USB_CAIAQ_INPUT=y

#
# PCMCIA devices
#
CONFIG_SND_VXPOCKET=m
CONFIG_SND_PDAUDIOCF=m

#
# System on Chip audio support
#
CONFIG_SND_SOC=m

#
# SoC Audio support for SuperH
#

#
# Open Sound System
#
CONFIG_SOUND_PRIME=m
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
CONFIG_SOUND_OSS=m
# CONFIG_SOUND_TRACEINIT is not set
# CONFIG_SOUND_DMAP is not set
CONFIG_SOUND_SSCAPE=m
CONFIG_SOUND_VMIDI=m
CONFIG_SOUND_TRIX=m
CONFIG_SOUND_MSS=m
CONFIG_SOUND_MPU401=m
# CONFIG_SOUND_PAS is not set
CONFIG_SOUND_PSS=m
CONFIG_PSS_MIXER=y
# CONFIG_SOUND_SB is not set
CONFIG_SOUND_YM3812=m
CONFIG_SOUND_UART6850=m
CONFIG_SOUND_AEDSP16=m
CONFIG_SC6600=y
CONFIG_SC6600_JOY=y
CONFIG_SC6600_CDROM=4
CONFIG_SC6600_CDROMBASE=0x0
# CONFIG_AEDSP16_MSS is not set
# CONFIG_AEDSP16_SBPRO is not set
CONFIG_AC97_BUS=m
CONFIG_HID_SUPPORT=y
CONFIG_HID=m
# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set

#
# USB Input Devices
#
CONFIG_USB_HID=m
CONFIG_USB_HIDINPUT_POWERBOOK=y
# CONFIG_HID_FF is not set
CONFIG_USB_HIDDEV=y

#
# USB HID Boot Protocol drivers
#
CONFIG_USB_KBD=m
CONFIG_USB_MOUSE=m
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
CONFIG_USB_SUSPEND=y
# CONFIG_USB_PERSIST is not set
# CONFIG_USB_OTG is not set

#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_EHCI_SPLIT_ISO=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_EHCI_TT_NEWSCHED=y
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_OHCI_HCD_SSB is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=m
CONFIG_USB_U132_HCD=m
CONFIG_USB_SL811_HCD=m
CONFIG_USB_SL811_CS=m
# CONFIG_USB_R8A66597_HCD is not set

#
# USB Device Class drivers
#
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m

#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#

#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_USBAT=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
CONFIG_USB_STORAGE_ALAUDA=y
CONFIG_USB_STORAGE_KARMA=y
CONFIG_USB_LIBUSUAL=y

#
# USB Imaging devices
#
CONFIG_USB_MDC800=m
CONFIG_USB_MICROTEK=m
CONFIG_USB_MON=y

#
# USB port drivers
#
CONFIG_USB_USS720=m

#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_AIRCABLE=m
CONFIG_USB_SERIAL_AIRPRIME=m
CONFIG_USB_SERIAL_ARK3116=m
CONFIG_USB_SERIAL_BELKIN=m
# CONFIG_USB_SERIAL_CH341 is not set
CONFIG_USB_SERIAL_WHITEHEAT=m
CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
CONFIG_USB_SERIAL_CP2101=m
CONFIG_USB_SERIAL_CYPRESS_M8=m
CONFIG_USB_SERIAL_EMPEG=m
CONFIG_USB_SERIAL_FTDI_SIO=m
CONFIG_USB_SERIAL_FUNSOFT=m
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_IPAQ=m
# CONFIG_USB_SERIAL_IR is not set
CONFIG_USB_SERIAL_EDGEPORT=m
CONFIG_USB_SERIAL_EDGEPORT_TI=m
CONFIG_USB_SERIAL_GARMIN=m
CONFIG_USB_SERIAL_IPW=m
CONFIG_USB_SERIAL_KEYSPAN_PDA=m
# CONFIG_USB_SERIAL_KEYSPAN is not set
CONFIG_USB_SERIAL_KLSI=m
CONFIG_USB_SERIAL_KOBIL_SCT=m
CONFIG_USB_SERIAL_MCT_U232=m
CONFIG_USB_SERIAL_MOS7720=m
CONFIG_USB_SERIAL_MOS7840=m
CONFIG_USB_SERIAL_NAVMAN=m
CONFIG_USB_SERIAL_PL2303=m
# CONFIG_USB_SERIAL_OTI6858 is not set
CONFIG_USB_SERIAL_HP4X=m
CONFIG_USB_SERIAL_SAFE=m
# CONFIG_USB_SERIAL_SAFE_PADDED is not set
CONFIG_USB_SERIAL_SIERRAWIRELESS=m
CONFIG_USB_SERIAL_TI=m
CONFIG_USB_SERIAL_CYBERJACK=m
CONFIG_USB_SERIAL_XIRCOM=m
CONFIG_USB_SERIAL_OPTION=m
CONFIG_USB_SERIAL_OMNINET=m
CONFIG_USB_SERIAL_DEBUG=m
CONFIG_USB_EZUSB=y

#
# USB Miscellaneous drivers
#
CONFIG_USB_EMI62=m
CONFIG_USB_EMI26=m
CONFIG_USB_ADUTUX=m
CONFIG_USB_AUERSWALD=m
CONFIG_USB_RIO500=m
CONFIG_USB_LEGOTOWER=m
CONFIG_USB_LCD=m
CONFIG_USB_BERRY_CHARGE=m
CONFIG_USB_LED=m
CONFIG_USB_CYPRESS_CY7C63=m
CONFIG_USB_CYTHERM=m
CONFIG_USB_PHIDGET=m
CONFIG_USB_PHIDGETKIT=m
CONFIG_USB_PHIDGETMOTORCONTROL=m
CONFIG_USB_PHIDGETSERVO=m
CONFIG_USB_IDMOUSE=m
CONFIG_USB_FTDI_ELAN=m
CONFIG_USB_APPLEDISPLAY=m
CONFIG_USB_SISUSBVGA=m
# CONFIG_USB_SISUSBVGA_CON is not set
CONFIG_USB_LD=m
CONFIG_USB_TRANCEVIBRATOR=m
CONFIG_USB_IOWARRIOR=m
# CONFIG_USB_TEST is not set

#
# USB DSL modem support
#
CONFIG_USB_ATM=m
CONFIG_USB_SPEEDTOUCH=m
CONFIG_USB_CXACRU=m
CONFIG_USB_UEAGLEATM=m
CONFIG_USB_XUSBATM=m

#
# USB Gadget Support
#
CONFIG_USB_GADGET=m
# CONFIG_USB_GADGET_DEBUG is not set
# CONFIG_USB_GADGET_DEBUG_FILES is not set
# CONFIG_USB_GADGET_DEBUG_FS is not set
CONFIG_USB_GADGET_SELECTED=y
# CONFIG_USB_GADGET_AMD5536UDC is not set
# CONFIG_USB_GADGET_ATMEL_USBA is not set
# CONFIG_USB_GADGET_FSL_USB2 is not set
CONFIG_USB_GADGET_NET2280=y
CONFIG_USB_NET2280=m
# CONFIG_USB_GADGET_PXA2XX is not set
# CONFIG_USB_GADGET_M66592 is not set
# CONFIG_USB_GADGET_GOKU is not set
# CONFIG_USB_GADGET_LH7A40X is not set
# CONFIG_USB_GADGET_OMAP is not set
# CONFIG_USB_GADGET_S3C2410 is not set
# CONFIG_USB_GADGET_AT91 is not set
# CONFIG_USB_GADGET_DUMMY_HCD is not set
CONFIG_USB_GADGET_DUALSPEED=y
CONFIG_USB_ZERO=m
CONFIG_USB_ETH=m
CONFIG_USB_ETH_RNDIS=y
CONFIG_USB_GADGETFS=m
CONFIG_USB_FILE_STORAGE=m
# CONFIG_USB_FILE_STORAGE_TEST is not set
CONFIG_USB_G_SERIAL=m
CONFIG_USB_MIDI_GADGET=m
CONFIG_MMC=m
# CONFIG_MMC_DEBUG is not set
# CONFIG_MMC_UNSAFE_RESUME is not set

#
# MMC/SD Card Drivers
#
CONFIG_MMC_BLOCK=m
CONFIG_MMC_BLOCK_BOUNCE=y
# CONFIG_SDIO_UART is not set

#
# MMC/SD Host Controller Drivers
#
CONFIG_MMC_SDHCI=m
# CONFIG_MMC_RICOH_MMC is not set
CONFIG_MMC_WBSD=m
CONFIG_MMC_TIFM_SD=m
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=m

#
# LED drivers
#
CONFIG_LEDS_NET48XX=m
CONFIG_LEDS_WRAP=m

#
# LED Triggers
#
# CONFIG_LEDS_TRIGGERS is not set
CONFIG_INFINIBAND=m
CONFIG_INFINIBAND_USER_MAD=m
CONFIG_INFINIBAND_USER_ACCESS=m
CONFIG_INFINIBAND_USER_MEM=y
CONFIG_INFINIBAND_ADDR_TRANS=y
CONFIG_INFINIBAND_MTHCA=m
CONFIG_INFINIBAND_MTHCA_DEBUG=y
CONFIG_INFINIBAND_AMSO1100=m
CONFIG_INFINIBAND_AMSO1100_DEBUG=y
CONFIG_INFINIBAND_CXGB3=m
# CONFIG_INFINIBAND_CXGB3_DEBUG is not set
CONFIG_MLX4_INFINIBAND=m
CONFIG_INFINIBAND_IPOIB=m
CONFIG_INFINIBAND_IPOIB_CM=y
CONFIG_INFINIBAND_IPOIB_DEBUG=y
# CONFIG_INFINIBAND_IPOIB_DEBUG_DATA is not set
CONFIG_INFINIBAND_SRP=m
CONFIG_INFINIBAND_ISER=m
# CONFIG_EDAC is not set
CONFIG_RTC_LIB=m
CONFIG_RTC_CLASS=m

#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=y
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
CONFIG_RTC_INTF_DEV_UIE_EMUL=y
CONFIG_RTC_DRV_TEST=m

#
# I2C RTC drivers
#
CONFIG_RTC_DRV_DS1307=m
# CONFIG_RTC_DRV_DS1374 is not set
CONFIG_RTC_DRV_DS1672=m
CONFIG_RTC_DRV_MAX6900=m
CONFIG_RTC_DRV_RS5C372=m
CONFIG_RTC_DRV_ISL1208=m
CONFIG_RTC_DRV_X1205=m
CONFIG_RTC_DRV_PCF8563=m
CONFIG_RTC_DRV_PCF8583=m
# CONFIG_RTC_DRV_M41T80 is not set

#
# SPI RTC drivers
#
CONFIG_RTC_DRV_RS5C348=m
CONFIG_RTC_DRV_MAX6902=m

#
# Platform RTC drivers
#
# CONFIG_RTC_DRV_CMOS is not set
CONFIG_RTC_DRV_DS1553=m
# CONFIG_RTC_DRV_STK17TA8 is not set
CONFIG_RTC_DRV_DS1742=m
CONFIG_RTC_DRV_M48T86=m
# CONFIG_RTC_DRV_M48T59 is not set
CONFIG_RTC_DRV_V3020=m

#
# on-CPU RTC drivers
#
# CONFIG_DMADEVICES is not set
# CONFIG_AUXDISPLAY is not set
CONFIG_VIRTUALIZATION=y
CONFIG_KVM=m
CONFIG_KVM_INTEL=m
CONFIG_KVM_AMD=m
CONFIG_LGUEST=m

#
# Userspace I/O
#
# CONFIG_UIO is not set
CONFIG_VIRTIO=y
CONFIG_VIRTIO_RING=y

#
# Firmware Drivers
#
# CONFIG_EDD is not set
CONFIG_EFI_VARS=y
CONFIG_DELL_RBU=m
CONFIG_DCDBAS=m
CONFIG_DMIID=y

#
# File systems
#
CONFIG_EXT2_FS=m
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=m
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=m
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=m
CONFIG_REISERFS_FS=m
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
CONFIG_REISERFS_FS_SECURITY=y
CONFIG_JFS_FS=m
CONFIG_JFS_POSIX_ACL=y
CONFIG_JFS_SECURITY=y
# CONFIG_JFS_DEBUG is not set
CONFIG_JFS_STATISTICS=y
CONFIG_FS_POSIX_ACL=y
CONFIG_XFS_FS=m
CONFIG_XFS_QUOTA=y
CONFIG_XFS_SECURITY=y
CONFIG_XFS_POSIX_ACL=y
CONFIG_XFS_RT=y
CONFIG_GFS2_FS=m
CONFIG_GFS2_FS_LOCKING_NOLOCK=m
CONFIG_GFS2_FS_LOCKING_DLM=m
CONFIG_OCFS2_FS=m
CONFIG_OCFS2_DEBUG_MASKLOG=y
# CONFIG_OCFS2_DEBUG_FS is not set
CONFIG_MINIX_FS=m
CONFIG_ROMFS_FS=m
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
CONFIG_QUOTA=y
# CONFIG_QUOTA_NETLINK_INTERFACE is not set
CONFIG_PRINT_QUOTA_WARNING=y
CONFIG_QFMT_V1=m
CONFIG_QFMT_V2=m
CONFIG_QUOTACTL=y
CONFIG_DNOTIFY=y
CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
# CONFIG_NTFS_RW is not set

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_VMCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_CONFIGFS_FS=m

#
# Miscellaneous filesystems
#
CONFIG_ADFS_FS=m
# CONFIG_ADFS_FS_RW is not set
CONFIG_AFFS_FS=m
CONFIG_ECRYPT_FS=m
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
CONFIG_BEFS_FS=m
# CONFIG_BEFS_DEBUG is not set
CONFIG_BFS_FS=m
CONFIG_EFS_FS=m
CONFIG_JFFS2_FS=m
CONFIG_JFFS2_FS_DEBUG=0
CONFIG_JFFS2_FS_WRITEBUFFER=y
# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
# CONFIG_JFFS2_SUMMARY is not set
# CONFIG_JFFS2_FS_XATTR is not set
# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
CONFIG_JFFS2_ZLIB=y
# CONFIG_JFFS2_LZO is not set
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
CONFIG_CRAMFS=y
CONFIG_VXFS_FS=m
CONFIG_HPFS_FS=m
CONFIG_QNX4FS_FS=m
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
# CONFIG_UFS_FS_WRITE is not set
# CONFIG_UFS_DEBUG is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
CONFIG_NFS_DIRECTIO=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
CONFIG_SUNRPC_XPRT_RDMA=m
# CONFIG_SUNRPC_BIND34 is not set
CONFIG_RPCSEC_GSS_KRB5=m
CONFIG_RPCSEC_GSS_SPKM3=m
CONFIG_SMB_FS=m
# CONFIG_SMB_NLS_DEFAULT is not set
CONFIG_CIFS=m
# CONFIG_CIFS_STATS is not set
# CONFIG_CIFS_WEAK_PW_HASH is not set
# CONFIG_CIFS_XATTR is not set
# CONFIG_CIFS_DEBUG2 is not set
# CONFIG_CIFS_EXPERIMENTAL is not set
CONFIG_NCP_FS=m
CONFIG_NCPFS_PACKET_SIGNING=y
CONFIG_NCPFS_IOCTL_LOCKING=y
CONFIG_NCPFS_STRONG=y
CONFIG_NCPFS_NFS_NS=y
CONFIG_NCPFS_OS2_NS=y
# CONFIG_NCPFS_SMALLDOS is not set
CONFIG_NCPFS_NLS=y
CONFIG_NCPFS_EXTRAS=y
CONFIG_CODA_FS=m
# CONFIG_CODA_FS_OLD_API is not set
CONFIG_AFS_FS=m
# CONFIG_AFS_DEBUG is not set

#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
CONFIG_ACORN_PARTITION=y
# CONFIG_ACORN_PARTITION_CUMANA is not set
# CONFIG_ACORN_PARTITION_EESOX is not set
CONFIG_ACORN_PARTITION_ICS=y
# CONFIG_ACORN_PARTITION_ADFS is not set
# CONFIG_ACORN_PARTITION_POWERTEC is not set
CONFIG_ACORN_PARTITION_RISCIX=y
CONFIG_OSF_PARTITION=y
CONFIG_AMIGA_PARTITION=y
CONFIG_ATARI_PARTITION=y
CONFIG_MAC_PARTITION=y
CONFIG_MSDOS_PARTITION=y
CONFIG_BSD_DISKLABEL=y
CONFIG_MINIX_SUBPARTITION=y
CONFIG_SOLARIS_X86_PARTITION=y
CONFIG_UNIXWARE_DISKLABEL=y
CONFIG_LDM_PARTITION=y
# CONFIG_LDM_DEBUG is not set
CONFIG_SGI_PARTITION=y
CONFIG_ULTRIX_PARTITION=y
CONFIG_SUN_PARTITION=y
CONFIG_KARMA_PARTITION=y
CONFIG_EFI_PARTITION=y
CONFIG_SYSV68_PARTITION=y
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="cp437"
CONFIG_NLS_CODEPAGE_437=m
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_936=m
CONFIG_NLS_CODEPAGE_950=m
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_CODEPAGE_949=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m
CONFIG_DLM=m
# CONFIG_DLM_DEBUG is not set
CONFIG_INSTRUMENTATION=y
CONFIG_PROFILING=y
CONFIG_OPROFILE=m
CONFIG_KPROBES=y
CONFIG_MARKERS=y

#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_PRINTK_TIME=y
CONFIG_ENABLE_WARN_DEPRECATED=y
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_MAGIC_SYSRQ=y
CONFIG_UNUSED_SYMBOLS=y
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
CONFIG_TIMER_STATS=y
# CONFIG_SLUB_DEBUG_ON is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_HIGHMEM is not set
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_FRAME_POINTER is not set
# CONFIG_FORCED_INLINING is not set
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_LKDTM is not set
# CONFIG_FAULT_INJECTION is not set
CONFIG_SAMPLES=y
CONFIG_SAMPLE_MARKERS=m
CONFIG_EARLY_PRINTK=y
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_PAGEALLOC is not set
# CONFIG_DEBUG_RODATA is not set
# CONFIG_4KSTACKS is not set
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
CONFIG_DOUBLEFAULT=y

#
# Security options
#
CONFIG_KEYS=y
# CONFIG_KEYS_DEBUG_PROC_KEYS is not set
CONFIG_SECURITY=y
CONFIG_SECURITY_NETWORK=y
# CONFIG_SECURITY_NETWORK_XFRM is not set
CONFIG_SECURITY_CAPABILITIES=y
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
CONFIG_SECURITY_SELINUX=y
CONFIG_SECURITY_SELINUX_BOOTPARAM=y
CONFIG_SECURITY_SELINUX_BOOTPARAM_VALUE=0
CONFIG_SECURITY_SELINUX_DISABLE=y
CONFIG_SECURITY_SELINUX_DEVELOP=y
CONFIG_SECURITY_SELINUX_AVC_STATS=y
CONFIG_SECURITY_SELINUX_CHECKREQPROT_VALUE=1
# CONFIG_SECURITY_SELINUX_ENABLE_SECMARK_DEFAULT is not set
# CONFIG_SECURITY_SELINUX_POLICYDB_VERSION_MAX is not set
CONFIG_XOR_BLOCKS=m
CONFIG_ASYNC_CORE=m
CONFIG_ASYNC_MEMCPY=m
CONFIG_ASYNC_XOR=m
CONFIG_CRYPTO=y
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ABLKCIPHER=m
CONFIG_CRYPTO_BLKCIPHER=m
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_WP512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_GF128MUL=m
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_CBC=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_LRW=m
# CONFIG_CRYPTO_XTS is not set
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_DES=m
CONFIG_CRYPTO_FCRYPT=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_TWOFISH_COMMON=m
CONFIG_CRYPTO_TWOFISH_586=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_AES_586=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_KHAZAD=m
CONFIG_CRYPTO_ANUBIS=m
# CONFIG_CRYPTO_SEED is not set
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_TEST=m
# CONFIG_CRYPTO_AUTHENC is not set
CONFIG_CRYPTO_HW=y
CONFIG_CRYPTO_DEV_PADLOCK=y
CONFIG_CRYPTO_DEV_PADLOCK_AES=m
CONFIG_CRYPTO_DEV_PADLOCK_SHA=m
CONFIG_CRYPTO_DEV_GEODE=m

#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
CONFIG_LIBCRC32C=m
CONFIG_AUDIT_GENERIC=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
CONFIG_GENERIC_ALLOCATOR=y
CONFIG_REED_SOLOMON=m
CONFIG_REED_SOLOMON_DEC16=y
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_TEXTSEARCH_BM=m
CONFIG_TEXTSEARCH_FSM=m
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
CONFIG_CHECK_SIGNATURE=y

ver_linux:

Linux machine 2.6.24-rc5-custom #1 SMP Wed Dec 12 23:18:52 EST 2007
i686 GNU/Linux

Gnu C 4.1.3
Gnu make 3.81
binutils 2.18
util-linux 2.13
mount 2.13
module-init-tools 3.3-pre2
e2fsprogs 1.40.2
reiserfsprogs 3.6.19
pcmciautils 014
PPP 2.4.4
Linux C Library 2.6.1
Dynamic linker (ldd) 2.6.1
Procps 3.2.7
Net-tools 1.60
Console-tools 0.2.3
Sh-utils 5.97
udev 113
wireless-tools 29
Modules Loaded af_packet rfcomm l2cap bluetooth ppdev ipv6 sbs
sbshc video output container dock ac battery power_supply parport_pc
lp parport psmouse serio_raw intel_agp shpchp pcspkr iTCO_wdt
iTCO_vendor_support e1000e agpgart pci_hotplug button evdev ext3 jbd
mbcache sr_mod cdrom sg sd_mod usb_storage usbhid hid libusual ahci
libata scsi_mod ehci_hcd uhci_hcd usbcore thermal processor fan fuse


/proc/modules:

af_packet 23684 2 - Live 0xf8c58000
rfcomm 41744 2 - Live 0xf8ceb000
l2cap 25728 11 rfcomm, Live 0xf8c50000
bluetooth 60132 4 rfcomm,l2cap, Live 0xf8c40000
ppdev 10500 0 - Live 0xf8c63000
ipv6 266756 16 - Live 0xf90a4000
sbs 15368 0 - Live 0xf8c2a000
sbshc 7936 1 sbs, Live 0xf8c27000
video 19728 0 - Live 0xf8c21000
output 4864 1 video, Live 0xf8c32000
container 5888 0 - Live 0xf8c1e000
dock 11408 0 - Live 0xf8c1a000
ac 7172 0 - Live 0xf8c35000
battery 14468 0 - Live 0xf8c3b000
power_supply 10116 3 sbs,ac,battery, Live 0xf89ec000
parport_pc 37284 0 - Live 0xf89e1000
lp 12580 0 - Live 0xf89c4000
parport 37960 3 ppdev,parport_pc,lp, Live 0xf89d6000
psmouse 40592 0 - Live 0xf89b9000
serio_raw 8196 0 - Live 0xf89b5000
intel_agp 25748 0 - Live 0xf89ad000
shpchp 34708 0 - Live 0xf89a1000
pcspkr 4352 0 - Live 0xf897c000
iTCO_wdt 13220 0 - Live 0xf8973000
iTCO_vendor_support 4996 1 iTCO_wdt, Live 0xf8970000
e1000e 98084 0 - Live 0xf8954000
agpgart 35016 1 intel_agp, Live 0xf8948000
pci_hotplug 31136 1 shpchp, Live 0xf893f000
button 9488 0 - Live 0xf890f000
evdev 13056 3 - Live 0xf890a000
ext3 135944 2 - Live 0xf891c000
jbd 48276 1 ext3, Live 0xf89c9000
mbcache 9728 1 ext3, Live 0xf8906000
sr_mod 18084 0 - Live 0xf8900000
cdrom 37280 1 sr_mod, Live 0xf88f5000
sg 37136 0 - Live 0xf88ea000
sd_mod 30592 5 - Live 0xf88b6000
usb_storage 73408 0 - Live 0xf88d7000
usbhid 32000 0 - Live 0xf88ce000
hid 32132 1 usbhid, Live 0xf8913000
libusual 19236 1 usb_storage, Live 0xf88b0000
ahci 28420 4 - Live 0xf889b000
libata 156400 1 ahci, Live 0xf89f1000
scsi_mod 151564 5 sr_mod,sg,sd_mod,usb_storage,libata, Live 0xf8874000
ehci_hcd 37388 0 - Live 0xf8869000
uhci_hcd 27024 0 - Live 0xf88a5000
usbcore 146412 6 usb_storage,usbhid,libusual,ehci_hcd,uhci_hcd, Live 0xf8844000
thermal 17052 0 - Live 0xf8838000
processor 30704 1 thermal, Live 0xf8828000
fan 5636 0 - Live 0xf8841000
fuse 50452 3 - Live 0xf88c0000


/proc/ioports:

0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0290-0297 : pnp 00:01
03c0-03df : vga+
0400-04bf : pnp 00:07
0400-0403 : ACPI PM1a_EVT_BLK
0404-0405 : ACPI PM1a_CNT_BLK
0408-040b : ACPI PM_TMR
0420-042f : ACPI GPE0_BLK
0460-047f : iTCO_wdt
04d0-04d1 : pnp 00:01
0500-051f : 0000:00:1f.3
0800-087f : pnp 00:01
0880-088f : pnp 00:01
0cf8-0cff : PCI conf1
c000-cfff : PCI Bus #02
d000-dfff : PCI Bus #01
df00-df7f : 0000:01:00.0
f400-f41f : 0000:00:1f.2
f500-f503 : 0000:00:1f.2
f600-f607 : 0000:00:1f.2
f700-f703 : 0000:00:1f.2
f800-f807 : 0000:00:1f.2
f900-f91f : 0000:00:1d.2
f900-f91f : uhci_hcd
fa00-fa1f : 0000:00:1d.1
fa00-fa1f : uhci_hcd
fb00-fb1f : 0000:00:1d.0
fb00-fb1f : uhci_hcd
fc00-fc1f : 0000:00:1a.2
fc00-fc1f : uhci_hcd
fd00-fd1f : 0000:00:1a.1
fd00-fd1f : uhci_hcd
fe00-fe1f : 0000:00:1a.0
fe00-fe1f : uhci_hcd
ff00-ff1f : 0000:00:19.0
ff00-ff1f : e1000e


/proc/iomem:

00000000-00099bff : System RAM
00099c00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000ccdff : Video ROM
000d3000-000d6fff : Adapter ROM
000f0000-000fffff : System ROM
00100000-7fe8ffff : System RAM
00100000-00305407 : Kernel code
00305408-003f4d83 : Kernel data
00455000-004cb6ff : Kernel bss
7fe90000-7fee2fff : ACPI Non-volatile Storage
7fee3000-7feeffff : ACPI Tables
7fef0000-7fefffff : reserved
7ff00000-7fffffff : pnp 00:0a
d0000000-dfffffff : PCI Bus #01
d0000000-dfffffff : 0000:01:00.0
e0000000-efffffff : PCI MMCONFIG 0
e0000000-efffffff : reserved
f8000000-fbffffff : PCI Bus #01
f8000000-f9ffffff : 0000:01:00.0
fa000000-faffffff : 0000:01:00.0
fb000000-fb01ffff : 0000:01:00.0
fdd00000-fddfffff : PCI Bus #02
fde00000-fdefffff : PCI Bus #02
fdfc0000-fdfdffff : 0000:00:19.0
fdfc0000-fdfdffff : e1000e
fdff4000-fdff7fff : 0000:00:1b.0
fdffb000-fdffb0ff : 0000:00:1f.3
fdffc000-fdffc7ff : 0000:00:1f.2
fdffc000-fdffc7ff : ahci
fdffd000-fdffd3ff : 0000:00:1d.7
fdffd000-fdffd3ff : ehci_hcd
fdffe000-fdffe3ff : 0000:00:1a.7
fdffe000-fdffe3ff : ehci_hcd
fdfff000-fdffffff : 0000:00:19.0
fdfff000-fdffffff : e1000e
fec00000-ffffffff : reserved
fed00000-fed003ff : HPET 0


lspci -vvv:

00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM
Controller (rev 02)
Subsystem: Dell Unknown device 023d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information

00:01.0 PCI bridge: Intel Corporation 82G33/G31/P35/P31 Express PCI
Express Root Port (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f8000000-fbffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [88] Subsystem: Dell Unknown device 023d
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0300c Data: 41b1
Capabilities: [a0] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Virtual Channel
Capabilities: [140] Unknown (5)

00:19.0 Ethernet controller: Intel Corporation 82562V-2 10/100 Network
Connection (rev 02)
Subsystem: Dell Unknown device 023d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 221
Region 0: Memory at fdfc0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fdfff000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at ff00 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee0300c Data: 41e9
Capabilities: [e0] Vendor Specific Information

00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB
UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device 023d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at fe00 [size=32]
Capabilities: [50] Vendor Specific Information

00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB
UHCI Controller #5 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device 023d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at fd00 [size=32]
Capabilities: [50] Vendor Specific Information

00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB
UHCI Controller #6 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device 023d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 18
Region 4: I/O ports at fc00 [size=32]
Capabilities: [50] Vendor Specific Information

00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2
EHCI Controller #2 (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell Unknown device 023d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 20
Region 0: Memory at fdffe000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio
Controller (rev 02)
Subsystem: Dell Unknown device 023d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 3
Region 0: Memory at fdff4000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)

00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB
UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device 023d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 4: I/O ports at fb00 [size=32]
Capabilities: [50] Vendor Specific Information

00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB
UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device 023d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 4: I/O ports at fa00 [size=32]
Capabilities: [50] Vendor Specific Information

00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB
UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device 023d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 20
Region 4: I/O ports at f900 [size=32]
Capabilities: [50] Vendor Specific Information

00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2
EHCI Controller #1 (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell Unknown device 023d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fdffd000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92)
(prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: 00000000fde00000-00000000fdefffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: Dell Unknown device 023d

00:1f.0 ISA bridge: Intel Corporation 82801IR (ICH9R) LPC Interface
Controller (rev 02)
Subsystem: Dell Unknown device 023d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information

00:1f.2 RAID bus controller: Intel Corporation 82801 SATA RAID
Controller (rev 02)
Subsystem: Dell Unknown device 023d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 222
Region 0: I/O ports at f800 [size=8]
Region 1: I/O ports at f700 [size=4]
Region 2: I/O ports at f600 [size=8]
Region 3: I/O ports at f500 [size=4]
Region 4: I/O ports at f400 [size=32]
Region 5: Memory at fdffc000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/4 Enable+
Address: fee0300c Data: 41d9
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] #12 [0010]
Capabilities: [b0] Vendor Specific Information

00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02)
Subsystem: Dell Unknown device 023d
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 11
Region 0: Memory at fdffb000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0500 [size=32]

01:00.0 VGA compatible controller: nVidia Corporation GeForce 8300 GS
(rev a1) (prog-if 00 [VGA])
Subsystem: nVidia Corporation Unknown device 0494
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at f8000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at df00 [size=128]
[virtual] Expansion ROM at fb000000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <512ns, L1 <4us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM unknown, Port 0
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Capabilities: [100] Virtual Channel
Capabilities: [128] Power Budgeting
Capabilities: [600] Unknown (11)


/proc/scsi/scsi:

Attached devices:
Host: scsi6 Channel: 00 Id: 00 Lun: 00
Vendor: Generic Model: Flash HS-CF Rev: 4.44
Type: Direct-Access ANSI SCSI revision: 00
Host: scsi6 Channel: 00 Id: 00 Lun: 01
Vendor: Generic Model: Flash HS-COMBO Rev: 4.44
Type: Direct-Access ANSI SCSI revision: 00
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: ATA Model: SAMSUNG HD321KJ Rev: CP10
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: HL-DT-ST Model: DVD-ROM GDRH20N Rev: 0D04
Type: CD-ROM ANSI SCSI revision: 05
Host: scsi4 Channel: 00 Id: 00 Lun: 00
Vendor: HL-DT-ST Model: DVD+-RW GSA-H73N Rev: B103
Type: CD-ROM ANSI SCSI revision: 05

/proc/mttr:

reg00: base=0x00000000 ( 0MB), size=2048MB: write-back, count=1
reg01: base=0x7ff00000 (2047MB), size= 1MB: uncachable, count=1

2007-12-14 09:53:52

by Andrew Morton

Subject: Re: PROBLEM: E6850 has an 8+ minute delay during boot

On Fri, 14 Dec 2007 04:10:31 -0500 "Arun Thomas" <[email protected]> wrote:

> My Dell Vostro desktop w/ an Intel E6850 dual-core 3GHz CPU has an 8+
> minute delay during boot. The machine seems to run fine after it
> boots. The problem occurs on the Ubuntu gutsy 2.6.22-14 kernel,
> 2.6.23.9, and 2.6.24-rc5. I have upgraded to the most recent Dell BIOS
> version (1.0.8). I am running an SMP kernel currently, but the problem
> presents itself in uniprocessor mode (nosmp) also. I'm running the
> machine in 32-bit mode w/hyperthreading configured.
>
> Here are a few interesting things in the dmesg output for the
> 2.6.24-rc5 kernel (smp). The full dmesg is also included farther down.
>
> [ 20.101501] CPU: After generic identify, caps: bfebfbff 20100000
> 00000000 00000000 0000e3fd 00000000 00000001 00000000
> [ 20.101505] monitor/mwait feature present.
> [ 20.101506] using mwait in idle threads.
> [ 20.101508] CPU: L1 I cache: 32K, L1 D cache: 32K
> [ 20.101509] CPU: L2 cache: 4096K
> [ 20.101511] CPU: Physical Processor ID: 0
> [ 20.101511] CPU: Processor Core ID: 0
> [ 20.101513] CPU: After all inits, caps: bfebfbff 20100000 00000000
> 00003940 0000e3fd 00000000 00000001 00000000
> [ 20.101517] Compat vDSO mapped to ffffe000.
> [ 20.101525] Checking 'hlt' instruction... OK.
> [ 20.117651] SMP alternatives: switching to UP code
> [ 20.118574] ACPI: Core revision 20070126
> [ 20.175154] CPU0: Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz stepping 0b
> [ 20.175163] SMP alternatives: switching to SMP code
> [ 20.175437] Booting processor 1/1 eip 3000
> [ 20.185881] Initializing CPU#1
> [ 527.926587] Calibrating delay using timer specific routine..
> 200566.59 BogoMIPS (lpj=401133185)
> [ 527.926592] CPU: After generic identify, caps: bfebfbff 20100000
> 00000000 00000000 0000e3fd 00000000 00000001 00000000
> [ 527.926595] monitor/mwait feature present.
> [ 527.926596] CPU: L1 I cache: 32K, L1 D cache: 32K
> [ 527.926597] CPU: L2 cache: 4096K
> [ 527.926599] CPU: Physical Processor ID: 0

Silly question: is that delay actually observeable by a human,
or is it just a leap in the printk timestamping?

2007-12-14 10:01:42

by Arun Thomas

Subject: Re: PROBLEM: E6850 has an 8+ minute delay during boot

On Dec 14, 2007 4:53 AM, Andrew Morton <[email protected]> wrote:
>
> On Fri, 14 Dec 2007 04:10:31 -0500 "Arun Thomas" <[email protected]> wrote:
>
> > [ 20.185881] Initializing CPU#1
> > [ 527.926587] Calibrating delay using timer specific routine..
> > 200566.59 BogoMIPS (lpj=401133185)
>
> Silly question: is that delay actually observeable by a human,
> or is it just a leap in the printk timestamping?

Good question. Yes, it's human-observable. The kernel "hangs" for 8
mins by my wall clock, and then it continues to boot up.

Thanks,
Arun

2007-12-14 10:18:39

by Jiri Slaby

Subject: Re: PROBLEM: E6850 has an 8+ minute delay during boot

On 12/14/2007 11:01 AM, Arun Thomas wrote:
> On Dec 14, 2007 4:53 AM, Andrew Morton <[email protected]> wrote:
>> On Fri, 14 Dec 2007 04:10:31 -0500 "Arun Thomas" <[email protected]> wrote:
>>

some time before:
[ 20.101392] Calibrating delay using timer specific routine..
5989.01 BogoMIPS (lpj=11978034)

>>> [ 20.185881] Initializing CPU#1
>>> [ 527.926587] Calibrating delay using timer specific routine..
>>> 200566.59 BogoMIPS (lpj=401133185)
>> Silly question: is that delay actually observeable by a human,
>> or is it just a leap in the printk timestamping?
>
> Good question. Yes, it's human-observable. The kernel "hangs" for 8
> mins by my wall clock, and then it continues to boot up.

By the way, the same processor here, but
Calibrating delay using timer specific routine.. 5984.76 BogoMIPS (lpj=11969527)
for the second core.

The calibration is some kind of weird there.

If any info needed from me, feel free to ask (x86_64 here). No problems with it
here AFAIK.

2007-12-14 10:44:18

by Thomas Gleixner

Subject: Re: PROBLEM: E6850 has an 8+ minute delay during boot

On Fri, 14 Dec 2007, Jiri Slaby wrote:

> On 12/14/2007 11:01 AM, Arun Thomas wrote:
> > On Dec 14, 2007 4:53 AM, Andrew Morton <[email protected]> wrote:
> >> On Fri, 14 Dec 2007 04:10:31 -0500 "Arun Thomas" <[email protected]> wrote:
> >>
>
> some time before:
> [ 20.101392] Calibrating delay using timer specific routine..
> 5989.01 BogoMIPS (lpj=11978034)
>
> >>> [ 20.185881] Initializing CPU#1
> >>> [ 527.926587] Calibrating delay using timer specific routine..
> >>> 200566.59 BogoMIPS (lpj=401133185)
> >> Silly question: is that delay actually observeable by a human,
> >> or is it just a leap in the printk timestamping?
> >
> > Good question. Yes, it's human-observable. The kernel "hangs" for 8
> > mins by my wall clock, and then it continues to boot up.
>
> By the way, the same processor here, but
> Calibrating delay using timer specific routine.. 5984.76 BogoMIPS (lpj=11969527)
> for the second core.
>
> The calibration is some kind of weird there.
>
> If any info needed from me, feel free to ask (x86_64 here). No problems with it
> here AFAIK.

The problem is caused by an SMI during the calibration routine. We
really need to come up with a solid solution which does not rely on
the periodic timer coming in, when there is something else (HPET,
pm_timer) available.

I have a look into this.

Arun, do you have an USB keyboard plugged in ? If not, can you connect
one and check, whether it changes things or not ?

Thanks,

tglx

2007-12-14 11:15:35

by Arun Thomas

Subject: Re: PROBLEM: E6850 has an 8+ minute delay during boot

On Dec 14, 2007 5:43 AM, Thomas Gleixner <[email protected]> wrote:

>
> Arun, do you have an USB keyboard plugged in ? If not, can you connect
> one and check, whether it changes things or not ?

I had a USB keyboard and mouse connected when I encountered the
problem. Do you want me to try with a PS/2 keyboard/mouse?

Thanks,
Arun

2007-12-14 14:38:42

by Mark Lord

Subject: Re: PROBLEM: E6850 has an 8+ minute delay during boot

Arun Thomas wrote:
...
> [ 31.670148] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
> [ 31.670351] TCP: Hash tables configured (established 131072 bind 65536)
> [ 31.670391] TCP reno registered
> [ 31.681591] checking if image is initramfs...<7>Switched to high
> resolution mode on CPU 0
> [ 540.133678] Clocksource tsc unstable (delta = 299978139535 ns)
> [ 540.137708] Time: hpet clocksource has been installed.
> [ 540.432798] it is
> [ 541.570364] Freeing initrd memory: 44428k freed
> [ 541.570748] audit: initializing netlink socket (disabled)
...

Ahh... BINGO!

This is very likely the same problem that I first reported back in 2.6.21(20?),
when NOHZ and HPET first came in!

It never occurred to me to wait a full 8-minutes though,
so I just rebooted again after a 1-2 minute wait each time.

Seen on Core2Duo T7400 and Core2Quad E6600 systems, with kernels 2.6.21/22
at various points. Not consistent -- sometimes it would boot after a few
attempts, sometimes not.

It always hung around the "Switched to high resolution mode" messages.

Thomas Gleixner wrote:
> The problem is caused by an SMI during the calibration routine. We
> really need to come up with a solid solution which does not rely on
> the periodic timer coming in, when there is something else (HPET,
> pm_timer) available.
...

Oh good, an explanation!

Now we just need a creative fix.

One thing that *might* be sufficient, would be to do the
delay loop calibration twice, and compare the results to
see if they're within 10% (pick a number) of each other.

Is there a flag or something that SMI sets that we could poll
before/after the calibration? That could be used to tell us
that it needs redoing ?

2007-12-14 14:44:59

by Mark Lord

Subject: Re: PROBLEM: E6850 has an 8+ minute delay during boot

Thomas Gleixner wrote:
..
> Arun, do you have an USB keyboard plugged in ? If not, can you connect
> one and check, whether it changes things or not ?
..

One of my two affected boxes has a USB mouse plugged in,
and it makes no difference one way or another.

No USB keyboards here, though.

Cheers

2007-12-14 19:02:31

by H. Peter Anvin

Subject: Re: PROBLEM: E6850 has an 8+ minute delay during boot

Thomas Gleixner wrote:
>
> The problem is caused by an SMI during the calibration routine. We
> really need to come up with a solid solution which does not rely on
> the periodic timer coming in, when there is something else (HPET,
> pm_timer) available.
>
> I have a look into this.
>
> Arun, do you have an USB keyboard plugged in ? If not, can you connect
> one and check, whether it changes things or not ?
>

How long is the SMI?

-hpa

2007-12-15 00:00:51

by Arun Thomas

Subject: Re: PROBLEM: E6850 has an 8+ minute delay during boot

On Dec 14, 2007 2:01 PM, H. Peter Anvin <[email protected]> wrote:
> Thomas Gleixner wrote:
> >
> > The problem is caused by an SMI during the calibration routine. We
> > really need to come up with a solid solution which does not rely on
> > the periodic timer coming in, when there is something else (HPET,
> > pm_timer) available.
>
> How long is the SMI?

Is there some instrumentation code somewhere which would allow me to
determine this? If not, can you give me some hints on where to add the
instrumentation code?

Thanks,
Arun

2007-12-15 00:39:40

by H. Peter Anvin

Subject: Re: PROBLEM: E6850 has an 8+ minute delay during boot

Arun Thomas wrote:
> On Dec 14, 2007 2:01 PM, H. Peter Anvin <[email protected]> wrote:
>> Thomas Gleixner wrote:
>>> The problem is caused by an SMI during the calibration routine. We
>>> really need to come up with a solid solution which does not rely on
>>> the periodic timer coming in, when there is something else (HPET,
>>> pm_timer) available.
>> How long is the SMI?
>
> Is there some instrumentation code somewhere which would allow me to
> determine this? If not, can you give me some hints on where to add the
> instrumentation code?

Well, the most obvious way to do it would be to run the calibration loop
a large number of times, and observe the statistical variation. In
particular, one should see a bi- or multimodal pattern where the
difference between the peaks amount to the "lost time".

When we have a clue about the loss of time then we can figure out how to
detect it.

-hpa

2007-12-15 06:07:43

by Len Brown

Subject: Re: PROBLEM: E6850 has an 8+ minute delay during boot

On Friday 14 December 2007 04:10, Arun Thomas wrote:
> Hi,
>
> My Dell Vostro desktop w/ an Intel E6850 dual-core 3GHz CPU has an 8+
> minute delay during boot. The machine seems to run fine after it
> boots. The problem occurs on the Ubuntu gutsy 2.6.22-14 kernel,
> 2.6.23.9, and 2.6.24-rc5. I have upgraded to the most recent Dell BIOS
> version (1.0.8). I am running an SMP kernel currently, but the problem
> presents itself in uniprocessor mode (nosmp) also. I'm running the
> machine in 32-bit mode w/hyperthreading configured.
>
> Here are a few interesting things in the dmesg output for the
> 2.6.24-rc5 kernel (smp). The full dmesg is also included farther down.
>
> [ 20.101501] CPU: After generic identify, caps: bfebfbff 20100000
> 00000000 00000000 0000e3fd 00000000 00000001 00000000
> [ 20.101505] monitor/mwait feature present.
> [ 20.101506] using mwait in idle threads.
> [ 20.101508] CPU: L1 I cache: 32K, L1 D cache: 32K
> [ 20.101509] CPU: L2 cache: 4096K
> [ 20.101511] CPU: Physical Processor ID: 0
> [ 20.101511] CPU: Processor Core ID: 0
> [ 20.101513] CPU: After all inits, caps: bfebfbff 20100000 00000000
> 00003940 0000e3fd 00000000 00000001 00000000
> [ 20.101517] Compat vDSO mapped to ffffe000.
> [ 20.101525] Checking 'hlt' instruction... OK.
> [ 20.117651] SMP alternatives: switching to UP code
> [ 20.118574] ACPI: Core revision 20070126
> [ 20.175154] CPU0: Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz stepping 0b
> [ 20.175163] SMP alternatives: switching to SMP code
> [ 20.175437] Booting processor 1/1 eip 3000
> [ 20.185881] Initializing CPU#1
> [ 527.926587] Calibrating delay using timer specific routine..
> 200566.59 BogoMIPS (lpj=401133185)
> [ 527.926592] CPU: After generic identify, caps: bfebfbff 20100000

try CONFIG_HIGH_RES_TIMERS=n
try "hpet=disable"

-Len

2007-12-16 05:38:25

by Arun Thomas

Subject: Re: PROBLEM: E6850 has an 8+ minute delay during boot

On Dec 15, 2007 1:07 AM, Len Brown <[email protected]> wrote:
<snip>
>
> try CONFIG_HIGH_RES_TIMERS=n
> try "hpet=disable"

The problem still manifests when I unset CONFIG_HIGH_RES_TIMERS,
CONFIG_HPET_TIMER, and CONFIG_NO_HZ (for good measure) in the kernel
config. The delay occurs later in the bootup process now. Here's a
dmesg snippet:

[ 31.895755] TCP established hash table entries: 131072 (order: 8,
1048576 bytes)
[ 31.896046] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 31.896203] TCP: Hash tables configured (established 131072 bind 65536)
[ 31.896244] TCP reno registered
[ 31.907674] checking if image is initramfs... it is
[ 541.796307] Freeing initrd memory: 44299k freed
[ 541.796748] audit: initializing netlink socket (disabled)
[ 541.796798] audit(1197764951.576:1): initialized

Thanks,
Arun

=====================

Full dmesg:

[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 2.6.24-rc5 (root@machine) (gcc version
4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #2 SMP Sat Dec
15 23:38:57 EST 2007
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 0000000000099c00 (usable)
[ 0.000000] BIOS-e820: 0000000000099c00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fe90000 (usable)
[ 0.000000] BIOS-e820: 000000007fe90000 - 000000007fee3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007fee3000 - 000000007fef0000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007fef0000 - 000000007ff00000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] 1150MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f3f00
[ 0.000000] Entering add_active_range(0, 0, 523920) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 523920
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 523920
[ 0.000000] On node 0 totalpages: 523920
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2301 pages used for memmap
[ 0.000000] HighMem zone: 292243 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.5 present.
[ 0.000000] ACPI: RSDP 000F97A0, 0024 (r2 DELL )
[ 0.000000] ACPI: XSDT 7FEE3080, 005C (r1 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: FACP 7FEE7200, 00F4 (r3 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: DSDT 7FEE3200, 3FFC (r1 DELL AWRDACPI 1000
MSFT 3000000)
[ 0.000000] ACPI: FACS 7FE90000, 0040
[ 0.000000] ACPI: HPET 7FEE73C0, 0038 (r1 DELL FX09 42302E31
AWRD 98)
[ 0.000000] ACPI: MCFG 7FEE7400, 003C (r1 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: SLIC 7FEE7440, 0176 (r1 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: DMY2 7FEE75C0, 0080 (r1 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: APIC 7FEE7300, 0084 (r1 DELL FX09 42302E31
AWRD 0)
[ 0.000000] ACPI: SSDT 7FEE7CA0, 0380 (r1 PmRef CpuPm 3000
INTL 20041203)
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:15 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 6:15 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 80000000 (gap:
7ff00000:60100000)
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 519827
[ 0.000000] Kernel command line:
root=UUID=8420f2d5-9569-476d-b3fc-6365a9987426 ro
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 2992.589 MHz processor.
[ 31.280619] Console: colour VGA+ 80x25
[ 31.280621] console [tty0] enabled
[ 31.283054] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 31.283251] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 31.342926] Memory: 2028880k/2095680k available (2049k kernel code,
65480k reserved, 949k data, 360k init, 1178176k highmem)
[ 31.342982] virtual kernel memory layout:
[ 31.342983] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 31.342983] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 31.342984] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 31.342985] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 31.342985] .init : 0xc03f3000 - 0xc044d000 ( 360 kB)
[ 31.342986] .data : 0xc0300798 - 0xc03edd84 ( 949 kB)
[ 31.342986] .text : 0xc0100000 - 0xc0300798 (2049 kB)
[ 31.343295] Checking if this processor honours the WP bit even in
supervisor mode... Ok.
[ 31.343395] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4,
CPUs=2, Nodes=1
[ 31.423420] Calibrating delay using timer specific routine..
5989.37 BogoMIPS (lpj=11978751)
[ 31.423512] Security Framework initialized
[ 31.423553] SELinux: Disabled at boot.
[ 31.423593] Capability LSM initialized
[ 31.423636] Mount-cache hash table entries: 512
[ 31.423747] Initializing cgroup subsys cpuacct
[ 31.423791] CPU: After generic identify, caps: bfebfbff 20100000
00000000 00000000 0000e3fd 00000000 00000001 00000000
[ 31.423795] monitor/mwait feature present.
[ 31.423833] using mwait in idle threads.
[ 31.423873] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 31.423938] CPU: L2 cache: 4096K
[ 31.423976] CPU: Physical Processor ID: 0
[ 31.424014] CPU: Processor Core ID: 0
[ 31.424051] CPU: After all inits, caps: bfebfbff 20100000 00000000
00003940 0000e3fd 00000000 00000001 00000000
[ 31.424056] Compat vDSO mapped to ffffe000.
[ 31.424101] Checking 'hlt' instruction... OK.
[ 31.439705] SMP alternatives: switching to UP code
[ 31.440655] ACPI: Core revision 20070126
[ 31.497466] CPU0: Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz stepping 0b
[ 31.497566] SMP alternatives: switching to SMP code
[ 31.497877] Booting processor 1/1 eip 3000
[ 31.508358] Initializing CPU#1
[ 31.587337] Calibrating delay using timer specific routine..
5985.38 BogoMIPS (lpj=11970776)
[ 31.587341] CPU: After generic identify, caps: bfebfbff 20100000
00000000 00000000 0000e3fd 00000000 00000001 00000000
[ 31.587344] monitor/mwait feature present.
[ 31.587346] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 31.587347] CPU: L2 cache: 4096K
[ 31.587348] CPU: Physical Processor ID: 0
[ 31.587349] CPU: Processor Core ID: 1
[ 31.587350] CPU: After all inits, caps: bfebfbff 20100000 00000000
00003940 0000e3fd 00000000 00000001 00000000
[ 31.587852] CPU1: Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz stepping 0b
[ 31.588225] Total of 2 processors activated (11974.76 BogoMIPS).
[ 31.588398] ENABLING IO-APIC IRQs
[ 31.588590] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 31.735333] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 31.755397] Brought up 2 CPUs
[ 31.755450] CPU0 attaching sched-domain:
[ 31.755451] domain 0: span 03
[ 31.755452] groups: 01 02
[ 31.755454] CPU1 attaching sched-domain:
[ 31.755455] domain 0: span 03
[ 31.755456] groups: 02 01
[ 31.755581] net_namespace: 64 bytes
[ 31.755622] Booting paravirtualized kernel on bare hardware
[ 31.755916] Time: 0:20:42 Date: 12/16/07
[ 31.755981] NET: Registered protocol family 16
[ 31.756111] EISA bus registered
[ 31.756150] ACPI: bus type pci registered
[ 31.756230] PCI: Using MMCONFIG
[ 31.756588] Setting up standard PCI resources
[ 31.757730] mtrr: your CPUs had inconsistent fixed MTRR settings
[ 31.757769] mtrr: probably your BIOS does not setup all CPUs.
[ 31.757809] mtrr: corrected configuration.
[ 31.758568] ACPI: EC: Look up EC in DSDT
[ 31.760761] ACPI: Interpreter enabled
[ 31.760800] ACPI: (supports S0 S3 S5)
[ 31.760920] ACPI: Using IOAPIC for interrupt routing
[ 31.763322] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 31.763929] PCI: Transparent bridge - 0000:00:1e.0
[ 31.763982] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 31.764081] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 31.772299] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[ 31.772714] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11
12 14 15) *0, disabled.
[ 31.773188] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11 12 14 15)
[ 31.773600] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 31.774015] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[ 31.774428] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 31.774841] ACPI: PCI Interrupt Link [LNK0] (IRQs *3 4 5 7 9 10 11 12 14 15)
[ 31.775256] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 *4 5 7 9 10 11 12 14 15)
[ 31.775673] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 31.775726] pnp: PnP ACPI init
[ 31.775766] ACPI: bus type pnp registered
[ 31.776735] pnpacpi: exceeded the max number of mem resources: 12
[ 31.776806] pnp: PnP ACPI: found 11 devices
[ 31.776844] ACPI: ACPI bus type pnp unregistered
[ 31.776883] PnPBIOS: Disabled by ACPI PNP
[ 31.777005] PCI: Using ACPI for IRQ routing
[ 31.777044] PCI: If a device doesn't work, try "pci=routeirq". If
it helps, post a report
[ 31.803468] NET: Registered protocol family 8
[ 31.803508] NET: Registered protocol family 20
[ 31.807325] Time: tsc clocksource has been installed.
[ 31.823514] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 31.823557] system 00:01: ioport range 0x800-0x87f has been reserved
[ 31.823603] system 00:01: ioport range 0x290-0x297 has been reserved
[ 31.823644] system 00:01: ioport range 0x880-0x88f has been reserved
[ 31.823687] system 00:07: ioport range 0x400-0x4bf has been reserved
[ 31.823730] system 00:09: iomem range 0xe0000000-0xefffffff could
not be reserved
[ 31.823780] system 00:0a: iomem range 0xf0000-0xfffff could not be reserved
[ 31.823822] system 00:0a: iomem range 0x7ff00000-0x7fffffff has been reserved
[ 31.823863] system 00:0a: iomem range 0xfed00000-0xfed000ff could
not be reserved
[ 31.823912] system 00:0a: iomem range 0x7fe90000-0x7fefffff could
not be reserved
[ 31.823961] system 00:0a: iomem range 0x0-0x9ffff could not be reserved
[ 31.824002] system 00:0a: iomem range 0x100000-0x7fe8ffff could not
be reserved
[ 31.824051] system 00:0a: iomem range 0xfec00000-0xfec00fff could
not be reserved
[ 31.824100] system 00:0a: iomem range 0xfed14000-0xfed1dfff could
not be reserved
[ 31.824149] system 00:0a: iomem range 0xfed20000-0xfed9ffff could
not be reserved
[ 31.824198] system 00:0a: iomem range 0xfee00000-0xfee00fff could
not be reserved
[ 31.824247] system 00:0a: iomem range 0xffb00000-0xffb7ffff could
not be reserved
[ 31.824296] system 00:0a: iomem range 0xfff00000-0xffffffff could
not be reserved
[ 31.854532] PCI: Bridge: 0000:00:01.0
[ 31.854569] IO window: d000-dfff
[ 31.854607] MEM window: f8000000-fbffffff
[ 31.854645] PREFETCH window: d0000000-dfffffff
[ 31.854684] PCI: Bridge: 0000:00:1e.0
[ 31.854722] IO window: c000-cfff
[ 31.854761] MEM window: fdd00000-fddfffff
[ 31.854799] PREFETCH window: fde00000-fdefffff
[ 31.854842] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level,
low) -> IRQ 16
[ 31.854918] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 31.854923] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 31.854928] NET: Registered protocol family 2
[ 31.895598] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 31.895755] TCP established hash table entries: 131072 (order: 8,
1048576 bytes)
[ 31.896046] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 31.896203] TCP: Hash tables configured (established 131072 bind 65536)
[ 31.896244] TCP reno registered
[ 31.907674] checking if image is initramfs... it is
[ 541.796307] Freeing initrd memory: 44299k freed
[ 541.796748] audit: initializing netlink socket (disabled)
[ 541.796798] audit(1197764951.576:1): initialized
[ 541.796967] highmem bounce pool size: 64 pages
[ 541.797994] VFS: Disk quotas dquot_6.5.1
[ 541.798068] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 541.798179] io scheduler noop registered
[ 541.798217] io scheduler anticipatory registered
[ 541.798256] io scheduler deadline registered
[ 541.798299] io scheduler cfq registered (default)
[ 541.798428] Boot video device is 0000:01:00.0
[ 541.798477] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 541.798487] assign_interrupt_mode Found MSI capability
[ 541.798535] Allocate Port Service[0000:00:01.0:pcie00]
[ 541.798553] Allocate Port Service[0000:00:01.0:pcie03]
[ 541.798659] isapnp: Scanning for PnP cards...
[ 542.151548] isapnp: No Plug & Play device found
[ 542.161922] Real Time Clock Driver v1.12ac
[ 542.161963] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports,
IRQ sharing enabled
[ 542.162597] RAMDISK driver initialized: 16 RAM disks of 65536K size
1024 blocksize
[ 542.162678] input: Macintosh mouse button emulation as /class/input/input0
[ 542.162785] PNP: No PS/2 controller found. Probing ports directly.
[ 542.163089] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 542.163132] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 542.192724] mice: PS/2 mouse device common for all mice
[ 542.192821] EISA: Probing bus 0 at eisa.0
[ 542.192879] EISA: Detected 0 cards.
[ 542.192958] TCP cubic registered
[ 542.192999] NET: Registered protocol family 1
[ 542.193051] Using IPI No-Shortcut mode
[ 542.193155] Magic number: 3:506:304
[ 542.193217] hash matches device tty33
[ 542.193362] Freeing unused kernel memory: 360k freed
[ 542.300168] fuse init (API version 7.9)
[ 542.302846] ACPI: Fan [FAN] (on)
[ 542.305823] ACPI: SSDT 7FEE7680, 022A (r1 PmRef Cpu0Ist 3000
INTL 20040311)
[ 542.306072] ACPI: SSDT 7FEE7B40, 0152 (r1 PmRef Cpu1Ist 3000
INTL 20040311)
[ 542.306242] ACPI Exception (processor_core-0816): AE_NOT_FOUND,
Processor Device is not present [20070126]
[ 542.306350] ACPI Exception (processor_core-0816): AE_NOT_FOUND,
Processor Device is not present [20070126]
[ 542.307254] ACPI: Thermal Zone [THRM] (40 C)
[ 542.585020] usbcore: registered new interface driver usbfs
[ 542.585078] usbcore: registered new interface driver hub
[ 542.585223] usbcore: registered new device driver usb
[ 542.586051] USB Universal Host Controller Interface driver v3.0
[ 542.586121] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level,
low) -> IRQ 16
[ 542.586202] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 542.586204] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 542.586341] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned
bus number 1
[ 542.586410] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000fe00
[ 542.586519] usb usb1: configuration #1 chosen from 1 choice
[ 542.586571] hub 1-0:1.0: USB hub found
[ 542.586610] hub 1-0:1.0: 2 ports detected
[ 542.628698] SCSI subsystem initialized
[ 542.638501] libata version 3.00 loaded.
[ 542.688450] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level,
low) -> IRQ 17
[ 542.688538] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 542.688541] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 542.688603] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned
bus number 2
[ 542.688675] uhci_hcd 0000:00:1a.1: irq 17, io base 0x0000fd00
[ 542.688775] usb usb2: configuration #1 chosen from 1 choice
[ 542.688826] hub 2-0:1.0: USB hub found
[ 542.688866] hub 2-0:1.0: 2 ports detected
[ 542.792623] ACPI: PCI Interrupt 0000:00:1a.2[D] -> GSI 19 (level,
low) -> IRQ 18
[ 542.792705] PCI: Setting latency timer of device 0000:00:1a.2 to 64
[ 542.792708] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 542.792772] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned
bus number 3
[ 542.792838] uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000fc00
[ 542.792932] usb usb3: configuration #1 chosen from 1 choice
[ 542.792983] hub 3-0:1.0: USB hub found
[ 542.793022] hub 3-0:1.0: 2 ports detected
[ 542.896839] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level,
low) -> IRQ 19
[ 542.896921] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 542.896923] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 542.896987] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned
bus number 4
[ 542.897052] uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000fb00
[ 542.897149] usb usb4: configuration #1 chosen from 1 choice
[ 542.897202] hub 4-0:1.0: USB hub found
[ 542.897242] hub 4-0:1.0: 2 ports detected
[ 543.001054] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level,
low) -> IRQ 18
[ 543.001136] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 543.001138] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 543.001194] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned
bus number 5
[ 543.001264] uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000fa00
[ 543.001363] usb usb5: configuration #1 chosen from 1 choice
[ 543.001414] hub 5-0:1.0: USB hub found
[ 543.001453] hub 5-0:1.0: 2 ports detected
[ 543.033190] usb 2-2: new full speed USB device using uhci_hcd and address 2
[ 543.105300] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level,
low) -> IRQ 20
[ 543.105382] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 543.105385] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 543.105442] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned
bus number 6
[ 543.105514] uhci_hcd 0000:00:1d.2: irq 20, io base 0x0000f900
[ 543.105609] usb usb6: configuration #1 chosen from 1 choice
[ 543.105660] hub 6-0:1.0: USB hub found
[ 543.105699] hub 6-0:1.0: 2 ports detected
[ 543.176521] usb 2-2: configuration #1 chosen from 1 choice
[ 543.179481] hub 2-2:1.0: USB hub found
[ 543.181464] hub 2-2:1.0: 2 ports detected
[ 543.209917] ahci 0000:00:1f.2: version 3.0
[ 543.209929] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 19 (level,
low) -> IRQ 18
[ 543.488295] usb 2-2.1: new full speed USB device using uhci_hcd and address 3
[ 543.610292] usb 2-2.1: configuration #1 chosen from 1 choice
[ 543.613243] hub 2-2.1:1.0: USB hub found
[ 543.615223] hub 2-2.1:1.0: 4 ports detected
[ 543.945043] usb 2-2.1.1: new full speed USB device using uhci_hcd
and address 4
[ 544.145997] usb 2-2.1.1: configuration #1 chosen from 1 choice
[ 544.216937] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3
Gbps 0x3f impl RAID mode
[ 544.216997] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pmp
pio slum part
[ 544.217047] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 544.217222] scsi0 : ahci
[ 544.217337] scsi1 : ahci
[ 544.217437] scsi2 : ahci
[ 544.217536] scsi3 : ahci
[ 544.217635] scsi4 : ahci
[ 544.217736] scsi5 : ahci
[ 544.217829] ata1: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc100 irq 222
[ 544.217878] ata2: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc180 irq 222
[ 544.217927] ata3: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc200 irq 222
[ 544.217977] ata4: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc280 irq 222
[ 544.218027] ata5: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc300 irq 222
[ 544.218077] ata6: SATA max UDMA/133 abar m2048@0xfdffc000 port
0xfdffc380 irq 222
[ 544.370809] usb 2-2.1.3: new low speed USB device using uhci_hcd
and address 5
[ 544.501803] usb 2-2.1.3: configuration #1 chosen from 1 choice
[ 544.723612] usb 2-2.1.4: new low speed USB device using uhci_hcd
and address 6
[ 544.894587] usb 2-2.1.4: configuration #1 chosen from 1 choice
[ 544.932540] usbcore: registered new interface driver hiddev
[ 544.932542] usbcore: registered new interface driver libusual
[ 544.936026] Initializing USB Mass Storage driver...
[ 544.936103] scsi6 : SCSI emulation for USB Mass Storage devices
[ 544.936175] usb-storage: device found at 4
[ 544.936176] usb-storage: waiting for device to settle before scanning
[ 544.945628] input: USB Optical Mouse as /class/input/input1
[ 544.971371] input: USB HID v1.11 Mouse [USB Optical Mouse] on
usb-0000:00:1a.1-2.1.3
[ 545.003628] input: Dell Dell USB Keyboard as /class/input/input2
[ 545.015490] input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard]
on usb-0000:00:1a.1-2.1.4
[ 545.015611] usbcore: registered new interface driver usbhid
[ 545.015614] usbcore: registered new interface driver usb-storage
[ 545.015618] USB Mass Storage support registered.
[ 545.015737] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 545.869242] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 545.886749] ata1.00: ATA-8: SAMSUNG HD321KJ, CP100-12, max UDMA7
[ 545.886792] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 545.888812] ata1.00: configured for UDMA/133
[ 547.536852] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 547.693849] ata2.00: ATAPI: HL-DT-STDVD-ROM GDRH20N, 0D04, max UDMA/100
[ 547.850200] ata2.00: configured for UDMA/100
[ 548.170055] ata3: SATA link down (SStatus 0 SControl 300)
[ 548.490720] ata4: SATA link down (SStatus 0 SControl 300)
[ 549.952738] usb-storage: device scan complete
[ 549.956746] scsi 6:0:0:0: Direct-Access Generic Flash HS-CF
4.44 PQ: 0 ANSI: 0
[ 549.960739] scsi 6:0:0:1: Direct-Access Generic Flash HS-COMBO
4.44 PQ: 0 ANSI: 0
[ 549.968762] sd 6:0:0:0: [sda] Attached SCSI removable disk
[ 550.018730] sd 6:0:0:1: [sdb] Attached SCSI removable disk
[ 550.021211] sd 6:0:0:0: Attached scsi generic sg0 type 0
[ 550.021263] sd 6:0:0:1: Attached scsi generic sg1 type 0
[ 550.142456] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 550.300526] ata5.00: ATAPI: HL-DT-ST DVD+/-RW GSA-H73N, B103, max UDMA/100
[ 550.456962] ata5.00: configured for UDMA/100
[ 550.775788] ata6: SATA link down (SStatus 0 SControl 300)
[ 550.775911] scsi 0:0:0:0: Direct-Access ATA SAMSUNG
HD321KJ CP10 PQ: 0 ANSI: 5
[ 550.776023] sd 0:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
[ 550.776071] sd 0:0:0:0: [sdc] Write Protect is off
[ 550.776110] sd 0:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 550.776123] sd 0:0:0:0: [sdc] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 550.776197] sd 0:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
[ 550.776243] sd 0:0:0:0: [sdc] Write Protect is off
[ 550.776282] sd 0:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 550.776294] sd 0:0:0:0: [sdc] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 550.776344] sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 sdc6 sdc7 >
[ 550.877505] sd 0:0:0:0: [sdc] Attached SCSI disk
[ 550.877562] sd 0:0:0:0: Attached scsi generic sg2 type 0
[ 550.878917] scsi 1:0:0:0: CD-ROM HL-DT-ST DVD-ROM
GDRH20N 0D04 PQ: 0 ANSI: 5
[ 550.879022] scsi 1:0:0:0: Attached scsi generic sg3 type 5
[ 550.880504] scsi 4:0:0:0: CD-ROM HL-DT-ST DVD+-RW
GSA-H73N B103 PQ: 0 ANSI: 5
[ 550.880611] scsi 4:0:0:0: Attached scsi generic sg4 type 5
[ 550.880827] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level,
low) -> IRQ 20
[ 550.880908] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 550.880910] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 550.880964] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned
bus number 7
[ 550.884903] PCI: cache line size of 32 is not supported by device
0000:00:1a.7
[ 550.884907] ehci_hcd 0000:00:1a.7: irq 20, io mem 0xfdffe000
[ 550.899634] sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
[ 550.899677] Uniform CD-ROM driver Revision: 3.20
[ 550.899739] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 550.900190] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00,
driver 10 Dec 2004
[ 550.900311] usb usb7: configuration #1 chosen from 1 choice
[ 550.900364] hub 7-0:1.0: USB hub found
[ 550.900404] hub 7-0:1.0: 6 ports detected
[ 550.905741] sr1: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 550.905806] sr 4:0:0:0: Attached scsi CD-ROM sr1
[ 551.004505] usb 2-2: USB disconnect, address 2
[ 551.004549] usb 2-2.1: USB disconnect, address 3
[ 551.004589] usb 2-2.1.1: USB disconnect, address 4
[ 551.004734] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level,
low) -> IRQ 19
[ 551.004821] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 551.004823] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 551.004878] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned
bus number 8
[ 551.005010] usb 2-2.1.3: USB disconnect, address 5
[ 551.008829] PCI: cache line size of 32 is not supported by device
0000:00:1d.7
[ 551.008832] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xfdffd000
[ 551.024639] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00,
driver 10 Dec 2004
[ 551.024761] usb usb8: configuration #1 chosen from 1 choice
[ 551.024814] hub 8-0:1.0: USB hub found
[ 551.024854] hub 8-0:1.0: 6 ports detected
[ 551.028654] usb 2-2.1.4: USB disconnect, address 6
[ 551.179613] kjournald starting. Commit interval 5 seconds
[ 551.179619] EXT3-fs: mounted filesystem with ordered data mode.
[ 551.429834] usb 7-4: new high speed USB device using ehci_hcd and address 2
[ 551.562688] usb 7-4: configuration #1 chosen from 1 choice
[ 551.562890] hub 7-4:1.0: USB hub found
[ 551.562994] hub 7-4:1.0: 2 ports detected
[ 551.867457] usb 7-4.1: new high speed USB device using ehci_hcd and address 3
[ 551.960221] usb 7-4.1: configuration #1 chosen from 1 choice
[ 551.960422] hub 7-4.1:1.0: USB hub found
[ 551.960526] hub 7-4.1:1.0: 4 ports detected
[ 552.264984] usb 7-4.1.1: new high speed USB device using ehci_hcd
and address 4
[ 552.444197] usb 7-4.1.1: configuration #1 chosen from 1 choice
[ 552.444444] scsi7 : SCSI emulation for USB Mass Storage devices
[ 552.444520] usb-storage: device found at 4
[ 552.444522] usb-storage: waiting for device to settle before scanning
[ 552.642526] usb 7-4.1.3: new low speed USB device using ehci_hcd
and address 5
[ 552.738030] usb 7-4.1.3: configuration #1 chosen from 1 choice
[ 552.739860] input: USB Optical Mouse as /class/input/input3
[ 552.750913] input: USB HID v1.11 Mouse [USB Optical Mouse] on
usb-0000:00:1a.7-4.1.3
[ 552.951980] usb 7-4.1.4: new low speed USB device using ehci_hcd
and address 6
[ 553.074968] usb 7-4.1.4: configuration #1 chosen from 1 choice
[ 553.087950] input: Dell Dell USB Keyboard as /class/input/input4
[ 553.100372] input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard]
on usb-0000:00:1a.7-4.1.4
[ 557.293650] iTCO_vendor_support: vendor-support=0
[ 557.450277] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[ 557.450375] iTCO_wdt: Found a ICH9R TCO device (Version=2, TCOBASE=0x0460)
[ 557.450440] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 557.471135] usb-storage: device scan complete
[ 557.474372] scsi 7:0:0:0: Direct-Access Generic Flash HS-CF
4.44 PQ: 0 ANSI: 0
[ 557.477622] scsi 7:0:0:1: Direct-Access Generic Flash HS-COMBO
4.44 PQ: 0 ANSI: 0
[ 557.481879] sd 7:0:0:0: [sda] Attached SCSI removable disk
[ 557.481944] sd 7:0:0:0: Attached scsi generic sg0 type 0
[ 557.531359] sd 7:0:0:1: [sdb] Attached SCSI removable disk
[ 557.531423] sd 7:0:0:1: Attached scsi generic sg1 type 0
[ 557.558508] input: Power Button (FF) as /class/input/input5
[ 557.599211] ACPI: Power Button (FF) [PWRF]
[ 557.599297] input: Power Button (CM) as /class/input/input6
[ 557.655383] ACPI: Power Button (CM) [PWRB]
[ 557.668439] e1000e: Intel(R) PRO/1000 Network Driver - 0.2.0
[ 557.668481] e1000e: Copyright (c) 1999-2007 Intel Corporation.
[ 557.668551] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level,
low) -> IRQ 21
[ 557.668636] PCI: Setting latency timer of device 0000:00:19.0 to 64
[ 557.689999] Linux agpgart interface v0.102
[ 557.710727] input: PC Speaker as /class/input/input7
[ 557.752890] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 557.757628] 0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1)
00:1a:a0:9e:5d:da
[ 557.757678] 0000:00:19.0: eth0: Intel(R) PRO/10/100 Network Connection
[ 557.757738] 0000:00:19.0: eth0: MAC: 5, PHY: 7, PBA No: ffffff-0ff
[ 557.763758] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 558.463971] lp: driver loaded but no devices found
[ 558.567849] Adding 4192924k swap on /dev/sdc6. Priority:-1
extents:1 across:4192924k
[ 558.778771] EXT3 FS on sdc7, internal journal
[ 559.111052] kjournald starting. Commit interval 5 seconds
[ 559.111272] EXT3 FS on sdc5, internal journal
[ 559.111275] EXT3-fs: mounted filesystem with ordered data mode.
[ 560.148929] No dock devices found.
[ 560.242879] toshiba_acpi: Unknown parameter `hotkeys_over_acpi'
[ 562.327992] NET: Registered protocol family 10
[ 562.328111] lo: Disabled Privacy Extensions
[ 562.328313] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 562.476637] ppdev: user-space parallel port driver
[ 562.867975] 0000:00:19.0: eth0: Link is Up 100 Mbps Full Duplex,
Flow Control: RX/TX
[ 562.867978] 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[ 562.868753] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 562.961715] Bluetooth: Core ver 2.11
[ 562.961751] NET: Registered protocol family 31
[ 562.961752] Bluetooth: HCI device and connection manager initialized
[ 562.961755] Bluetooth: HCI socket layer initialized
[ 562.974402] Bluetooth: L2CAP ver 2.9
[ 562.974405] Bluetooth: L2CAP socket layer initialized
[ 563.056090] Bluetooth: RFCOMM socket layer initialized
[ 563.056099] Bluetooth: RFCOMM TTY layer initialized
[ 563.056100] Bluetooth: RFCOMM ver 1.8
[ 567.180365] NET: Registered protocol family 17
[ 579.175070] eth0: no IPv6 routers present