From: Peter Robinson <[email protected]>
Pinebook Pro is a RK3399 based laptop produced by Pine64.
Add a basic DTS for it.
Signed-off-by: Peter Robinson <[email protected]>
Signed-off-by: Emmanuel Vadot <[email protected]>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3399-pinebook-pro.dts | 626 ++++++++++++++++++
2 files changed, 627 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 48fb631d5451..9099fb7e2073 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -28,6 +28,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopc-t4.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-m4.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-neo4.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-orangepi.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-mezzanine.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
new file mode 100644
index 000000000000..d2e3d7b35cc6
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
@@ -0,0 +1,626 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3399.dtsi"
+#include "rk3399-opp.dtsi"
+
+/ {
+ model = "Pine64 Pinebook Pro";
+ compatible = "pine64,pinebook-pro", "rockchip,rk3399";
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ aliases {
+ spi0 = &spi1;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ enable-gpios = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
+ pwms = <&pwm0 0 740740 0>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwrbtn>;
+
+ power {
+ debounce-interval = <100>;
+ gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+ label = "GPIO Key Power";
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ leds {
+ status = "okay";
+ compatible = "gpio-leds";
+
+ work-led {
+ label = "work";
+ gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
+ };
+
+ standby-led {
+ label = "standby";
+ gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc1v8_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_1v8>;
+ };
+
+ dc_12v: dc-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "dc_12v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc3v3_sys: vcc3v3-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc5v0_host: vcc5v0-host-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host_vbus_drv>;
+ regulator-name = "vcc5v0_host";
+ };
+
+ vcc5v0_usb3_host: vcc5v0-usb3-host-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host_usb3_drv>;
+ regulator-name = "vcc5v0_usb3_host";
+ regulator-always-on;
+ };
+
+ vcc3v3_s0: vcc3v3-s0-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdvcc_en>;
+ regulator-name = "vcc3v3_s0";
+ regulator-always-on;
+ };
+
+ vcc_sys: vcc-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_12v>;
+ };
+
+ vdd_log: vdd-log {
+ compatible = "pwm-regulator";
+ pwms = <&pwm2 0 25000 1>;
+ pwm-supply = <&vcc_sys>;
+ regulator-name = "vdd_log";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-init-microvolt = <950000>;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ };
+};
+
+&cpu_l0 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l1 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l2 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l3 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&emmc_phy {
+ status = "okay";
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+ i2c-scl-rising-time-ns = <168>;
+ i2c-scl-falling-time-ns = <4>;
+ status = "okay";
+
+ rk808: pmic@1b {
+ compatible = "rockchip,rk808";
+ reg = <0x1b>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk808-clkout2";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc6-supply = <&vcc_sys>;
+ vcc7-supply = <&vcc_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc_sys>;
+ vcc10-supply = <&vcc_sys>;
+ vcc11-supply = <&vcc_sys>;
+ vcc12-supply = <&vcc3v3_sys>;
+ vddio-supply = <&vcc_1v8>;
+
+ regulators {
+ vdd_center: DCDC_REG1 {
+ regulator-name = "vdd_center";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_l: DCDC_REG2 {
+ regulator-name = "vdd_cpu_l";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG4 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc1v8_dvp: LDO_REG1 {
+ regulator-name = "vcc1v8_dvp";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v0_touch: LDO_REG2 {
+ regulator-name = "vcc3v0_touch";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3000000>;
+ };
+ };
+
+ vcc1v8_pmu: LDO_REG3 {
+ regulator-name = "vcc1v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_sdio: LDO_REG4 {
+ regulator-name = "vcc_sdio";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca3v0_codec: LDO_REG5 {
+ regulator-name = "vcca3v0_codec";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v5: LDO_REG6 {
+ regulator-name = "vcc_1v5";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1500000>;
+ };
+ };
+
+ vcca1v8_codec: LDO_REG7 {
+ regulator-name = "vcca1v8_codec";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v0: LDO_REG8 {
+ regulator-name = "vcc_3v0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3000000>;
+ };
+ };
+
+ vcc3v3_s3: SWITCH_REG1 {
+ regulator-name = "vcc3v3_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ switch_reg2: SWITCH_REG2 {
+ regulator-name = "SWITCH_REG2";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+
+ vdd_cpu_b: regulator@40 {
+ compatible = "silergy,syr827";
+ reg = <0x40>;
+ fcs,suspend-voltage-selector = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vsel1_gpio>;
+ vsel-gpios = <&gpio1 RK_PC1 GPIO_ACTIVE_HIGH>;
+ regulator-compatible = "fan53555-reg";
+ regulator-name = "vdd_cpu_b";
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1500000>;
+ regulator-ramp-delay = <1000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: regulator@41 {
+ compatible = "silergy,syr828";
+ reg = <0x41>;
+ fcs,suspend-voltage-selector = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vsel2_gpio>;
+ vsel-gpios = <&gpio1 RK_PB6 GPIO_ACTIVE_HIGH>;
+ regulator-compatible = "fan53555-reg";
+ regulator-name = "vdd_gpu";
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1500000>;
+ regulator-ramp-delay = <1000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+};
+
+&i2c4 {
+ i2c-scl-rising-time-ns = <600>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+
+ fusb0: typec-portc@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&fusb0_int>;
+ vbus-supply = <&vcc5v0_usb3_host>;
+ status = "okay";
+ };
+};
+
+&io_domains {
+ status = "okay";
+
+ bt656-supply = <&vcc1v8_dvp>;
+ audio-supply = <&vcca1v8_codec>;
+ sdmmc-supply = <&vcc_sdio>;
+ gpio1830-supply = <&vcc_3v0>;
+};
+
+&pmu_io_domains {
+ pmu1830-supply = <&vcc_3v0>;
+ status = "okay";
+};
+
+&pinctrl {
+ buttons {
+ pwrbtn: pwrbtn {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ fusb302x {
+ fusb0_int: fusb0-int {
+ rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ vsel1_gpio: vsel1-gpio {
+ rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ vsel2_gpio: vsel2-gpio {
+ rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb-typec {
+ vcc5v0_typec_en: vcc5v0_typec_en {
+ rockchip,pins = <1 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb2 {
+ vcc5v0_host_en: vcc5v0-host-en {
+ rockchip,pins = <4 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ host_vbus_drv: host-vbus-drv {
+ rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ host_usb3_drv: host-usb3-drv {
+ rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ /* Shared between LCD and usb */
+ lcdvcc_en: lcdvcc-en {
+ rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pwm0 {
+ status = "okay";
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&saradc {
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ status = "okay";
+ max-frequency = <20000000>;
+};
+
+&sdhci {
+ bus-width = <8>;
+ max-frequency = <25000000>;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ non-removable;
+ status = "okay";
+};
+
+&tcphy0 {
+ status = "okay";
+};
+
+&tcphy1 {
+ status = "okay";
+};
+
+&tsadc {
+ /* tshut mode 0:CRU 1:GPIO */
+ rockchip,hw-tshut-mode = <1>;
+ /* tshut polarity 0:LOW 1:HIGH */
+ rockchip,hw-tshut-polarity = <1>;
+ status = "okay";
+};
+
+&u2phy0 {
+ status = "okay";
+
+ u2phy0_otg: otg-port {
+ status = "okay";
+ };
+
+ u2phy0_host: host-port {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+ };
+};
+
+&u2phy1 {
+ status = "okay";
+
+ u2phy1_otg: otg-port {
+ status = "okay";
+ };
+
+ u2phy1_host: host-port {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+ };
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ phy-supply = <&vcc3v3_s0>;
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ phy-supply = <&vcc3v3_s0>;
+ status = "okay";
+};
+
+&usbdrd3_0 {
+ status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+ status = "okay";
+ dr_mode = "otg";
+};
+
+&usbdrd3_1 {
+ status = "okay";
+};
+
+&usbdrd_dwc3_1 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&spi1 {
+ status = "okay";
+
+ spiflash: spi-flash@0 {
+ #address-cells = <0x1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-max-frequency = <10000000>;
+ status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ loader@8000 {
+ label = "loader";
+ reg = <0x0 0x3F8000>;
+ };
+
+ env@3f8000 {
+ label = "env";
+ reg = <0x3F8000 0x8000>;
+ };
+
+ vendor@7c0000 {
+ label = "vendor";
+ reg = <0x7C0000 0x40000>;
+ };
+ };
+ };
+};
--
2.24.1
Hi,
overall looks good, but some small things below
Am Donnerstag, 16. Januar 2020, 23:56:17 CET schrieb Emmanuel Vadot:
> From: Peter Robinson <[email protected]>
>
> Pinebook Pro is a RK3399 based laptop produced by Pine64.
>
> Add a basic DTS for it.
>
> Signed-off-by: Peter Robinson <[email protected]>
> Signed-off-by: Emmanuel Vadot <[email protected]>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3399-pinebook-pro.dts | 626 ++++++++++++++++++
> 2 files changed, 627 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index 48fb631d5451..9099fb7e2073 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -28,6 +28,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopc-t4.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-m4.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-neo4.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-orangepi.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-mezzanine.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
> new file mode 100644
> index 000000000000..d2e3d7b35cc6
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
> @@ -0,0 +1,626 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
You might want to clarify the copyright ... 2020 and Pine64-something?
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/pwm/pwm.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include "rk3399.dtsi"
> +#include "rk3399-opp.dtsi"
> +
> +/ {
> + model = "Pine64 Pinebook Pro";
> + compatible = "pine64,pinebook-pro", "rockchip,rk3399";
> +
> + chosen {
> + stdout-path = "serial2:115200n8";
> + };
> +
> + aliases {
> + spi0 = &spi1;
why is this needed ... I'd think spi can just enumerate itself?
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + enable-gpios = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
> + pwms = <&pwm0 0 740740 0>;
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + autorepeat;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwrbtn>;
> +
> + power {
> + debounce-interval = <100>;
> + gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
> + label = "GPIO Key Power";
> + linux,code = <KEY_POWER>;
> + wakeup-source;
> + };
> + };
> +
> + leds {
> + status = "okay";
new board-specific nodes don't need a status property
> + compatible = "gpio-leds";
> +
> + work-led {
> + label = "work";
> + gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
> + };
> +
> + standby-led {
> + label = "standby";
> + gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc1v8_s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_1v8>;
> + };
> +
> + dc_12v: dc-12v {
> + compatible = "regulator-fixed";
> + regulator-name = "dc_12v";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + };
> +
> + vcc3v3_sys: vcc3v3-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + vcc5v0_host: vcc5v0-host-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&host_vbus_drv>;
> + regulator-name = "vcc5v0_host";
> + };
> +
> + vcc5v0_usb3_host: vcc5v0-usb3-host-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&host_usb3_drv>;
> + regulator-name = "vcc5v0_usb3_host";
> + regulator-always-on;
> + };
> +
> + vcc3v3_s0: vcc3v3-s0-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&lcdvcc_en>;
> + regulator-name = "vcc3v3_s0";
> + regulator-always-on;
> + };
> +
> + vcc_sys: vcc-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&dc_12v>;
> + };
> +
> + vdd_log: vdd-log {
> + compatible = "pwm-regulator";
> + pwms = <&pwm2 0 25000 1>;
> + pwm-supply = <&vcc_sys>;
> + regulator-name = "vdd_log";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-init-microvolt = <950000>;
There is no init-microvolt property in mainline, I'd think bootloader should
already setup the pwm to a suitable setting?
Not
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1400000>;
> + };
> +};
> +
> +&cpu_l0 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l1 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l2 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l3 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
what happened to cpu_b0 and cpu_b1 supplies?
Should probably reference the cpu_b regulator below?
> +
> +&emmc_phy {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + clock-frequency = <400000>;
> + i2c-scl-rising-time-ns = <168>;
> + i2c-scl-falling-time-ns = <4>;
> + status = "okay";
[...]
> + vdd_cpu_b: regulator@40 {
> + compatible = "silergy,syr827";
> + reg = <0x40>;
> + fcs,suspend-voltage-selector = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vsel1_gpio>;
> + vsel-gpios = <&gpio1 RK_PC1 GPIO_ACTIVE_HIGH>;
This is not yet specified in the syr82x (fan5355) bindings and
also unknown to the driver
> + regulator-compatible = "fan53555-reg";
> + regulator-name = "vdd_cpu_b";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-ramp-delay = <1000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu: regulator@41 {
> + compatible = "silergy,syr828";
> + reg = <0x41>;
> + fcs,suspend-voltage-selector = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vsel2_gpio>;
> + vsel-gpios = <&gpio1 RK_PB6 GPIO_ACTIVE_HIGH>;
same
> + regulator-compatible = "fan53555-reg";
> + regulator-name = "vdd_gpu";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-ramp-delay = <1000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> +};
[...]
> +&saradc {
> + status = "okay";
needs a vref-supply
> +};
> +
> +&sdmmc {
> + bus-width = <4>;
> + status = "okay";
> + max-frequency = <20000000>;
vmmc / vqmmc supplies?
Especially if one wants to achieve higher speeds on uhs cards.
Heiko
On Sun, 19 Jan 2020 21:17:39 +0100
Heiko St?bner <[email protected]> wrote:
> Hi,
>
> overall looks good, but some small things below
>
> Am Donnerstag, 16. Januar 2020, 23:56:17 CET schrieb Emmanuel Vadot:
> > From: Peter Robinson <[email protected]>
> >
> > Pinebook Pro is a RK3399 based laptop produced by Pine64.
> >
> > Add a basic DTS for it.
> >
> > Signed-off-by: Peter Robinson <[email protected]>
> > Signed-off-by: Emmanuel Vadot <[email protected]>
> > ---
> > arch/arm64/boot/dts/rockchip/Makefile | 1 +
> > .../boot/dts/rockchip/rk3399-pinebook-pro.dts | 626 ++++++++++++++++++
> > 2 files changed, 627 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
> >
> > diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> > index 48fb631d5451..9099fb7e2073 100644
> > --- a/arch/arm64/boot/dts/rockchip/Makefile
> > +++ b/arch/arm64/boot/dts/rockchip/Makefile
> > @@ -28,6 +28,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopc-t4.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-m4.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-neo4.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-orangepi.dtb
> > +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-mezzanine.dtb
> > diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
> > new file mode 100644
> > index 000000000000..d2e3d7b35cc6
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
> > @@ -0,0 +1,626 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
>
> You might want to clarify the copyright ... 2020 and Pine64-something?
This is a DTS that Peter Robinson first wrote, I've just kept the
copyright.
> > + */
> > +
> > +/dts-v1/;
> > +#include <dt-bindings/input/linux-event-codes.h>
> > +#include <dt-bindings/pwm/pwm.h>
> > +#include <dt-bindings/pinctrl/rockchip.h>
> > +#include "rk3399.dtsi"
> > +#include "rk3399-opp.dtsi"
> > +
> > +/ {
> > + model = "Pine64 Pinebook Pro";
> > + compatible = "pine64,pinebook-pro", "rockchip,rk3399";
> > +
> > + chosen {
> > + stdout-path = "serial2:115200n8";
> > + };
> > +
> > + aliases {
> > + spi0 = &spi1;
>
> why is this needed ... I'd think spi can just enumerate itself?
This was taken from u-boot and yes I think it's not needed for both
Linux and FreeBSD.
>
> > + };
> > +
> > + backlight: backlight {
> > + compatible = "pwm-backlight";
> > + enable-gpios = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
> > + pwms = <&pwm0 0 740740 0>;
> > + };
> > +
> > + gpio-keys {
> > + compatible = "gpio-keys";
> > + autorepeat;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pwrbtn>;
> > +
> > + power {
> > + debounce-interval = <100>;
> > + gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
> > + label = "GPIO Key Power";
> > + linux,code = <KEY_POWER>;
> > + wakeup-source;
> > + };
> > + };
> > +
> > + leds {
> > + status = "okay";
>
> new board-specific nodes don't need a status property
Ok.
> > + compatible = "gpio-leds";
> > +
> > + work-led {
> > + label = "work";
> > + gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + standby-led {
> > + label = "standby";
> > + gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
> > + };
> > + };
> > +
> > + vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc1v8_s3";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + vin-supply = <&vcc_1v8>;
> > + };
> > +
> > + dc_12v: dc-12v {
> > + compatible = "regulator-fixed";
> > + regulator-name = "dc_12v";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <12000000>;
> > + regulator-max-microvolt = <12000000>;
> > + };
> > +
> > + vcc3v3_sys: vcc3v3-sys {
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc3v3_sys";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + vin-supply = <&vcc_sys>;
> > + };
> > +
> > + vcc5v0_host: vcc5v0-host-regulator {
> > + compatible = "regulator-fixed";
> > + gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&host_vbus_drv>;
> > + regulator-name = "vcc5v0_host";
> > + };
> > +
> > + vcc5v0_usb3_host: vcc5v0-usb3-host-regulator {
> > + compatible = "regulator-fixed";
> > + enable-active-high;
> > + gpio = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&host_usb3_drv>;
> > + regulator-name = "vcc5v0_usb3_host";
> > + regulator-always-on;
> > + };
> > +
> > + vcc3v3_s0: vcc3v3-s0-regulator {
> > + compatible = "regulator-fixed";
> > + enable-active-high;
> > + gpio = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&lcdvcc_en>;
> > + regulator-name = "vcc3v3_s0";
> > + regulator-always-on;
> > + };
> > +
> > + vcc_sys: vcc-sys {
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc_sys";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + vin-supply = <&dc_12v>;
> > + };
> > +
> > + vdd_log: vdd-log {
> > + compatible = "pwm-regulator";
> > + pwms = <&pwm2 0 25000 1>;
> > + pwm-supply = <&vcc_sys>;
> > + regulator-name = "vdd_log";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-init-microvolt = <950000>;
>
> There is no init-microvolt property in mainline, I'd think bootloader should
> already setup the pwm to a suitable setting?
>
> Not
I'll fix that.
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <1400000>;
> > + };
> > +};
> > +
> > +&cpu_l0 {
> > + cpu-supply = <&vdd_cpu_l>;
> > +};
> > +
> > +&cpu_l1 {
> > + cpu-supply = <&vdd_cpu_l>;
> > +};
> > +
> > +&cpu_l2 {
> > + cpu-supply = <&vdd_cpu_l>;
> > +};
> > +
> > +&cpu_l3 {
> > + cpu-supply = <&vdd_cpu_l>;
> > +};
>
> what happened to cpu_b0 and cpu_b1 supplies?
> Should probably reference the cpu_b regulator below?
Yes, sorry.
> > +
> > +&emmc_phy {
> > + status = "okay";
> > +};
> > +
> > +&i2c0 {
> > + clock-frequency = <400000>;
> > + i2c-scl-rising-time-ns = <168>;
> > + i2c-scl-falling-time-ns = <4>;
> > + status = "okay";
>
> [...]
>
> > + vdd_cpu_b: regulator@40 {
> > + compatible = "silergy,syr827";
> > + reg = <0x40>;
> > + fcs,suspend-voltage-selector = <1>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&vsel1_gpio>;
> > + vsel-gpios = <&gpio1 RK_PC1 GPIO_ACTIVE_HIGH>;
>
> This is not yet specified in the syr82x (fan5355) bindings and
> also unknown to the driver
I'll have another look at the bindings, thanks.
> > + regulator-compatible = "fan53555-reg";
> > + regulator-name = "vdd_cpu_b";
> > + regulator-min-microvolt = <712500>;
> > + regulator-max-microvolt = <1500000>;
> > + regulator-ramp-delay = <1000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + vin-supply = <&vcc_sys>;
> > +
> > + regulator-state-mem {
> > + regulator-off-in-suspend;
> > + };
> > + };
> > +
> > + vdd_gpu: regulator@41 {
> > + compatible = "silergy,syr828";
> > + reg = <0x41>;
> > + fcs,suspend-voltage-selector = <1>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&vsel2_gpio>;
> > + vsel-gpios = <&gpio1 RK_PB6 GPIO_ACTIVE_HIGH>;
>
> same
>
> > + regulator-compatible = "fan53555-reg";
> > + regulator-name = "vdd_gpu";
> > + regulator-min-microvolt = <712500>;
> > + regulator-max-microvolt = <1500000>;
> > + regulator-ramp-delay = <1000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + vin-supply = <&vcc_sys>;
> > +
> > + regulator-state-mem {
> > + regulator-off-in-suspend;
> > + };
> > + };
> > +
> > +};
>
> [...]
>
> > +&saradc {
> > + status = "okay";
>
> needs a vref-supply
>
> > +};
> > +
> > +&sdmmc {
> > + bus-width = <4>;
> > + status = "okay";
> > + max-frequency = <20000000>;
>
> vmmc / vqmmc supplies?
> Especially if one wants to achieve higher speeds on uhs cards.
Yep, will do that.
> Heiko
>
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> [email protected]
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
Emmanuel Vadot <[email protected]> <[email protected]>
Hi,
I do strongly oppose merging this DTS. It is missing several device
components (for example the eDP panel and the lid switch) and the power
supply setup does not reflect the implementation in the device at all.
Also some control/irq GPIOs are incorrect. See comments below.
The schematic of the Pinebook Pro can be found here:
http://files.pine64.org/doc/PinebookPro/pinebookpro_v2.1_mainboard_schematic.pdf
I'm currently planning on submitting a DTS with correct power supply and
GPIO setup as well as more supported hardware components late February.
Unfortunately I won't get around to doing it any sooner.
Current state of the DTS can be found here:
https://gitlab.manjaro.org/tsys/linux-pinebook-pro/blob/v5.5-rc7/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
> From: Peter Robinson <[email protected]>
>
> + gpio-keys {
> + compatible = "gpio-keys";
> + autorepeat;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwrbtn>;
> +
> + power {
> + debounce-interval = <100>;
> + gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
> + label = "GPIO Key Power";
> + linux,code = <KEY_POWER>;
> + wakeup-source;
> + };
Missing lid switch
> + };
> +
> + leds {
> + status = "okay";
> + compatible = "gpio-leds";
> +
> + work-led {
> + label = "work";
> + gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
> + };
> +
> + standby-led {
> + label = "standby";
> + gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
vcc1v8_s3 and vcca1v8_s3 are not the same. They are powered from
different vin supplies.
> + compatible = "regulator-fixed";
> + regulator-name = "vcc1v8_s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_1v8>;
> + };
> +
> + dc_12v: dc-12v {
> + compatible = "regulator-fixed";
> + regulator-name = "dc_12v";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + };
There is no primary 12 V supply on the Pinebook Pro
> +
> + vcc3v3_sys: vcc3v3-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + vcc5v0_host: vcc5v0-host-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&host_vbus_drv>;
> + regulator-name = "vcc5v0_host";
> + };
> +
> + vcc5v0_usb3_host: vcc5v0-usb3-host-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&host_usb3_drv>;
> + regulator-name = "vcc5v0_usb3_host";
> + regulator-always-on;
> + };
> +
> + vcc3v3_s0: vcc3v3-s0-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&lcdvcc_en>;
> + regulator-name = "vcc3v3_s0";
> + regulator-always-on;
> + };
> +
> + vcc_sys: vcc-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&dc_12v>;
> + };
> +The main system voltage is not 5 V and it is not powered by a 12 V rail
> + vdd_log: vdd-log {
> + compatible = "pwm-regulator";
> + pwms = <&pwm2 0 25000 1>;
> + pwm-supply = <&vcc_sys>;
> + regulator-name = "vdd_log";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-init-microvolt = <950000>;
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1400000>;
> + };
> +};
> +
Regulators for backlight, 0.9 V rail, USB-C power out and SD card power
are missing
Also most regulator names do not match the names of the power rails in
the schematic
> +&cpu_l0 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l1 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l2 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l3 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&emmc_phy {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + clock-frequency = <400000>;
> + i2c-scl-rising-time-ns = <168>;
> + i2c-scl-falling-time-ns = <4>;
> + status = "okay";
> +
> + rk808: pmic@1b {
> + compatible = "rockchip,rk808";
> + reg = <0x1b>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
Interrupt GPIO is not correct, should be 10. This will stop the RTC from
working correctly.
> + #clock-cells = <1>;
> + clock-output-names = "xin32k", "rk808-clkout2";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int_l>;
> + rockchip,system-power-controller;
> + wakeup-source;
> +
> + vcc1-supply = <&vcc_sys>;
> + vcc2-supply = <&vcc_sys>;
> + vcc3-supply = <&vcc_sys>;
> + vcc4-supply = <&vcc_sys>;
> + vcc6-supply = <&vcc_sys>;
> + vcc7-supply = <&vcc_sys>;
> + vcc8-supply = <&vcc3v3_sys>;
> + vcc9-supply = <&vcc_sys>;
> + vcc10-supply = <&vcc_sys>;
> + vcc11-supply = <&vcc_sys>;
> + vcc12-supply = <&vcc3v3_sys>;
> + vddio-supply = <&vcc_1v8>;
vddio-supply is not vcc_1v8 but vcc_3v0
> +
> + regulators {
> + vdd_center: DCDC_REG1 {
> + regulator-name = "vdd_center";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_cpu_l: DCDC_REG2 {
> + regulator-name = "vdd_cpu_l";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-name = "vcc_ddr";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_1v8: DCDC_REG4 {
> + regulator-name = "vcc_1v8";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc1v8_dvp: LDO_REG1 {
> + regulator-name = "vcc1v8_dvp";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc3v0_touch: LDO_REG2 {
> + regulator-name = "vcc3v0_touch";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3000000>;
> + };
> + };
> +
> + vcc1v8_pmu: LDO_REG3 {
> + regulator-name = "vcc1v8_pmu";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc_sdio: LDO_REG4 {
> + regulator-name = "vcc_sdio";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcca3v0_codec: LDO_REG5 {
> + regulator-name = "vcca3v0_codec";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_1v5: LDO_REG6 {
> + regulator-name = "vcc_1v5";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1500000>;
> + };
> + };
> +
> + vcca1v8_codec: LDO_REG7 {
> + regulator-name = "vcca1v8_codec";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_3v0: LDO_REG8 {
> + regulator-name = "vcc_3v0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3000000>;
> + };
> + };
> +
> + vcc3v3_s3: SWITCH_REG1 {
> + regulator-name = "vcc3v3_s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + switch_reg2: SWITCH_REG2 {
> + regulator-name = "SWITCH_REG2";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> + };
> + };
> +
> + vdd_cpu_b: regulator@40 {
> + compatible = "silergy,syr827";
> + reg = <0x40>;
> + fcs,suspend-voltage-selector = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vsel1_gpio>;
> + vsel-gpios = <&gpio1 RK_PC1 GPIO_ACTIVE_HIGH>;
> + regulator-compatible = "fan53555-reg";
> + regulator-name = "vdd_cpu_b";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-ramp-delay = <1000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu: regulator@41 {
> + compatible = "silergy,syr828";
> + reg = <0x41>;
> + fcs,suspend-voltage-selector = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vsel2_gpio>;
> + vsel-gpios = <&gpio1 RK_PB6 GPIO_ACTIVE_HIGH>;
> + regulator-compatible = "fan53555-reg";
> + regulator-name = "vdd_gpu";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-ramp-delay = <1000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> +};
Additionally there a quite a few components missing. This includes the
aforementioned lid switch and eDP panel but there are also a battery
gauge, two chargers, a es8316 audio codec, two speaker amplifiers and a
BT/WiFi module.
Best regards,
Tobias
Hi,
Am Dienstag, 21. Januar 2020, 15:13:06 CET schrieb Tobias Schramm:
> I do strongly oppose merging this DTS. It is missing several device
> components (for example the eDP panel and the lid switch) and the power
> supply setup does not reflect the implementation in the device at all.
> Also some control/irq GPIOs are incorrect. See comments below.
>
> The schematic of the Pinebook Pro can be found here:
> http://files.pine64.org/doc/PinebookPro/pinebookpro_v2.1_mainboard_schematic.pdf
>
> I'm currently planning on submitting a DTS with correct power supply and
> GPIO setup as well as more supported hardware components late February.
> Unfortunately I won't get around to doing it any sooner.
>
> Current state of the DTS can be found here:
> https://gitlab.manjaro.org/tsys/linux-pinebook-pro/blob/v5.5-rc7/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
I really like power trees that match the actual schematics, so I'm all
for it ;-) . I don't have a Pinebook Pro myself, so won't be comparing
the power-tree to the schematics myself though.
As for timing, it's too late for 5.6 anyway, so you have time until
around 5.6-rc5 gets released so around 8 weeks.
The other parts you can coordinate between you ;-)
Heiko
> > From: Peter Robinson <[email protected]>
> >
>
> > + gpio-keys {
> > + compatible = "gpio-keys";
> > + autorepeat;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pwrbtn>;
> > +
> > + power {
> > + debounce-interval = <100>;
> > + gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
> > + label = "GPIO Key Power";
> > + linux,code = <KEY_POWER>;
> > + wakeup-source;
> > + };
>
> Missing lid switch
> > + };
> > +
> > + leds {
> > + status = "okay";
> > + compatible = "gpio-leds";
> > +
> > + work-led {
> > + label = "work";
> > + gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + standby-led {
> > + label = "standby";
> > + gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
> > + };
> > + };
> > +
> > + vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
> vcc1v8_s3 and vcca1v8_s3 are not the same. They are powered from
> different vin supplies.
>
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc1v8_s3";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + vin-supply = <&vcc_1v8>;
> > + };
> > +
> > + dc_12v: dc-12v {
> > + compatible = "regulator-fixed";
> > + regulator-name = "dc_12v";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <12000000>;
> > + regulator-max-microvolt = <12000000>;
> > + };
> There is no primary 12 V supply on the Pinebook Pro
>
> > +
> > + vcc3v3_sys: vcc3v3-sys {
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc3v3_sys";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + vin-supply = <&vcc_sys>;
> > + };
> > +
> > + vcc5v0_host: vcc5v0-host-regulator {
> > + compatible = "regulator-fixed";
> > + gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&host_vbus_drv>;
> > + regulator-name = "vcc5v0_host";
> > + };
> > +
> > + vcc5v0_usb3_host: vcc5v0-usb3-host-regulator {
> > + compatible = "regulator-fixed";
> > + enable-active-high;
> > + gpio = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&host_usb3_drv>;
> > + regulator-name = "vcc5v0_usb3_host";
> > + regulator-always-on;
> > + };
> > +
> > + vcc3v3_s0: vcc3v3-s0-regulator {
> > + compatible = "regulator-fixed";
> > + enable-active-high;
> > + gpio = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&lcdvcc_en>;
> > + regulator-name = "vcc3v3_s0";
> > + regulator-always-on;
> > + };
> > +
> > + vcc_sys: vcc-sys {
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc_sys";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + vin-supply = <&dc_12v>;
> > + };
> > +The main system voltage is not 5 V and it is not powered by a 12 V rail
>
> > + vdd_log: vdd-log {
> > + compatible = "pwm-regulator";
> > + pwms = <&pwm2 0 25000 1>;
> > + pwm-supply = <&vcc_sys>;
> > + regulator-name = "vdd_log";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-init-microvolt = <950000>;
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <1400000>;
> > + };
> > +};
> > +
>
> Regulators for backlight, 0.9 V rail, USB-C power out and SD card power
> are missing
>
> Also most regulator names do not match the names of the power rails in
> the schematic
>
> > +&cpu_l0 {
> > + cpu-supply = <&vdd_cpu_l>;
> > +};
> > +
> > +&cpu_l1 {
> > + cpu-supply = <&vdd_cpu_l>;
> > +};
> > +
> > +&cpu_l2 {
> > + cpu-supply = <&vdd_cpu_l>;
> > +};
> > +
> > +&cpu_l3 {
> > + cpu-supply = <&vdd_cpu_l>;
> > +};
> > +
> > +&emmc_phy {
> > + status = "okay";
> > +};
> > +
> > +&i2c0 {
> > + clock-frequency = <400000>;
> > + i2c-scl-rising-time-ns = <168>;
> > + i2c-scl-falling-time-ns = <4>;
> > + status = "okay";
> > +
> > + rk808: pmic@1b {
> > + compatible = "rockchip,rk808";
> > + reg = <0x1b>;
> > + interrupt-parent = <&gpio1>;
> > + interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
> Interrupt GPIO is not correct, should be 10. This will stop the RTC from
> working correctly.
>
> > + #clock-cells = <1>;
> > + clock-output-names = "xin32k", "rk808-clkout2";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pmic_int_l>;
> > + rockchip,system-power-controller;
> > + wakeup-source;
> > +
> > + vcc1-supply = <&vcc_sys>;
> > + vcc2-supply = <&vcc_sys>;
> > + vcc3-supply = <&vcc_sys>;
> > + vcc4-supply = <&vcc_sys>;
> > + vcc6-supply = <&vcc_sys>;
> > + vcc7-supply = <&vcc_sys>;
> > + vcc8-supply = <&vcc3v3_sys>;
> > + vcc9-supply = <&vcc_sys>;
> > + vcc10-supply = <&vcc_sys>;
> > + vcc11-supply = <&vcc_sys>;
> > + vcc12-supply = <&vcc3v3_sys>;
> > + vddio-supply = <&vcc_1v8>;
> vddio-supply is not vcc_1v8 but vcc_3v0
>
> > +
> > + regulators {
> > + vdd_center: DCDC_REG1 {
> > + regulator-name = "vdd_center";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <750000>;
> > + regulator-max-microvolt = <1350000>;
> > + regulator-ramp-delay = <6001>;
> > + regulator-state-mem {
> > + regulator-off-in-suspend;
> > + };
> > + };
> > +
> > + vdd_cpu_l: DCDC_REG2 {
> > + regulator-name = "vdd_cpu_l";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <750000>;
> > + regulator-max-microvolt = <1350000>;
> > + regulator-ramp-delay = <6001>;
> > + regulator-state-mem {
> > + regulator-off-in-suspend;
> > + };
> > + };
> > +
> > + vcc_ddr: DCDC_REG3 {
> > + regulator-name = "vcc_ddr";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + };
> > + };
> > +
> > + vcc_1v8: DCDC_REG4 {
> > + regulator-name = "vcc_1v8";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <1800000>;
> > + };
> > + };
> > +
> > + vcc1v8_dvp: LDO_REG1 {
> > + regulator-name = "vcc1v8_dvp";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-state-mem {
> > + regulator-off-in-suspend;
> > + };
> > + };
> > +
> > + vcc3v0_touch: LDO_REG2 {
> > + regulator-name = "vcc3v0_touch";
> > + regulator-min-microvolt = <3000000>;
> > + regulator-max-microvolt = <3000000>;
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <3000000>;
> > + };
> > + };
> > +
> > + vcc1v8_pmu: LDO_REG3 {
> > + regulator-name = "vcc1v8_pmu";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <1800000>;
> > + };
> > + };
> > +
> > + vcc_sdio: LDO_REG4 {
> > + regulator-name = "vcc_sdio";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <3300000>;
> > + };
> > + };
> > +
> > + vcca3v0_codec: LDO_REG5 {
> > + regulator-name = "vcca3v0_codec";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <3000000>;
> > + regulator-max-microvolt = <3000000>;
> > + regulator-state-mem {
> > + regulator-off-in-suspend;
> > + };
> > + };
> > +
> > + vcc_1v5: LDO_REG6 {
> > + regulator-name = "vcc_1v5";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <1500000>;
> > + regulator-max-microvolt = <1500000>;
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <1500000>;
> > + };
> > + };
> > +
> > + vcca1v8_codec: LDO_REG7 {
> > + regulator-name = "vcca1v8_codec";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-state-mem {
> > + regulator-off-in-suspend;
> > + };
> > + };
> > +
> > + vcc_3v0: LDO_REG8 {
> > + regulator-name = "vcc_3v0";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-min-microvolt = <3000000>;
> > + regulator-max-microvolt = <3000000>;
> > + regulator-state-mem {
> > + regulator-on-in-suspend;
> > + regulator-suspend-microvolt = <3000000>;
> > + };
> > + };
> > +
> > + vcc3v3_s3: SWITCH_REG1 {
> > + regulator-name = "vcc3v3_s3";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-state-mem {
> > + regulator-off-in-suspend;
> > + };
> > + };
> > +
> > + switch_reg2: SWITCH_REG2 {
> > + regulator-name = "SWITCH_REG2";
> > + regulator-state-mem {
> > + regulator-off-in-suspend;
> > + };
> > + };
> > + };
> > + };
> > +
> > + vdd_cpu_b: regulator@40 {
> > + compatible = "silergy,syr827";
> > + reg = <0x40>;
> > + fcs,suspend-voltage-selector = <1>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&vsel1_gpio>;
> > + vsel-gpios = <&gpio1 RK_PC1 GPIO_ACTIVE_HIGH>;
> > + regulator-compatible = "fan53555-reg";
> > + regulator-name = "vdd_cpu_b";
> > + regulator-min-microvolt = <712500>;
> > + regulator-max-microvolt = <1500000>;
> > + regulator-ramp-delay = <1000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + vin-supply = <&vcc_sys>;
> > +
> > + regulator-state-mem {
> > + regulator-off-in-suspend;
> > + };
> > + };
> > +
> > + vdd_gpu: regulator@41 {
> > + compatible = "silergy,syr828";
> > + reg = <0x41>;
> > + fcs,suspend-voltage-selector = <1>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&vsel2_gpio>;
> > + vsel-gpios = <&gpio1 RK_PB6 GPIO_ACTIVE_HIGH>;
> > + regulator-compatible = "fan53555-reg";
> > + regulator-name = "vdd_gpu";
> > + regulator-min-microvolt = <712500>;
> > + regulator-max-microvolt = <1500000>;
> > + regulator-ramp-delay = <1000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + vin-supply = <&vcc_sys>;
> > +
> > + regulator-state-mem {
> > + regulator-off-in-suspend;
> > + };
> > + };
> > +
> > +};
>
> Additionally there a quite a few components missing. This includes the
> aforementioned lid switch and eDP panel but there are also a battery
> gauge, two chargers, a es8316 audio codec, two speaker amplifiers and a
> BT/WiFi module.
>
> Best regards,
>
> Tobias
>
>