I have a desktop system that has started having problems booting up in the morning.
It appears to just happen on more recent kernels.
I was having unrelated CDROM problems with a driver in an old kernel and decided
to test 2.6.27-rcX
The CDROM problem is fine now.
However I started having problems on -rc1. I found that the machine was hanging
soon after booting and needed a reboot. After a reboot it would work fine for
the rest of the day.
When -rc3 came out I tried that and the problem still appears to be there.
The normal process is now to boot to single-user, ctrl-alt-sysreq-SUB and then
reboot to multi-user. This isn't ideal.
If I cold boot 2.6.25.3 the problem doesn't occur.
I will try different versions over the next few days.
Sample log from a few days back. (2.6.27-rc1 I think)
The problem does cause filesystem crashes so I'm cautious about messing around
unguided.
Happy to try any suggestions.
David
PS I've run memtest and it's fine.
Aug 12 09:49:10 (none) syslogd 1.5.0#5: restart.
Aug 12 09:49:10 (none) kernel: klogd 1.5.0#5, log source = /proc/kmsg started.
Aug 12 09:49:10 (none) kernel: ddr 00:04:e2:cd:ac:db
Aug 12 09:49:10 (none) kernel: via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by
Donald Becker
Aug 12 09:49:10 (none) kernel: via-rhine 0000:00:12.0: PCI INT A -> GSI 23
(level, low) -> IRQ 23
Aug 12 09:49:10 (none) kernel: eth1: VIA Rhine II at 0xdd000000,
00:11:2f:cd:d0:b6, IRQ 23.
Aug 12 09:49:10 (none) kernel: eth1: MII PHY found at address 1, status 0x7849
advertising 01e1 Link 0000.
Aug 12 09:49:10 (none) kernel: netconsole: local port 6665
Aug 12 09:49:10 (none) kernel: netconsole: local IP 10.0.0.74
Aug 12 09:49:10 (none) kernel: netconsole: interface eth0
Aug 12 09:49:10 (none) kernel: netconsole: remote port 6666
Aug 12 09:49:10 (none) kernel: netconsole: remote IP 10.0.0.7
Aug 12 09:49:10 (none) kernel: netconsole: remote ethernet address 00:13:20:55:b6:60
Aug 12 09:49:10 (none) kernel: netconsole: device eth0 not up yet, forcing it
Aug 12 09:49:10 (none) kernel: skge eth0: enabling interface
Aug 12 09:49:10 (none) kernel: skge eth0: Link is up at 1000 Mbps, full duplex,
flow control both
Aug 12 09:49:10 (none) kernel: console [netcon0] enabled
Aug 12 09:49:10 (none) kernel: netconsole: network logging started
Aug 12 09:49:10 (none) kernel: Driver 'sd' needs updating - please use bus_type
methods
Aug 12 09:49:10 (none) kernel: Driver 'sr' needs updating - please use bus_type
methods
Aug 12 09:49:10 (none) kernel: sata_sil 0000:00:0a.0: version 2.3
Aug 12 09:49:10 (none) kernel: sata_sil 0000:00:0a.0: PCI INT A -> GSI 16
(level, low) -> IRQ 16
Aug 12 09:49:10 (none) kernel: scsi0 : sata_sil
Aug 12 09:49:10 (none) kernel: scsi1 : sata_sil
Aug 12 09:49:10 (none) kernel: ata1: SATA max UDMA/100 mmio m512@0xde800000 tf
0xde800080 irq 16
Aug 12 09:49:10 (none) kernel: ata2: SATA max UDMA/100 mmio m512@0xde800000 tf
0xde8000c0 irq 16
Aug 12 09:49:10 (none) kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl
310)
Aug 12 09:49:10 (none) kernel: ata1.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
Aug 12 09:49:10 (none) kernel: ata1.00: 625142448 sectors, multi 0: LBA48 NCQ
(depth 0/32)
Aug 12 09:49:10 (none) kernel: ata1.00: configured for UDMA/100
Aug 12 09:49:10 (none) kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
310)
Aug 12 09:49:10 (none) kernel: ata2.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133
Aug 12 09:49:10 (none) kernel: ata2.00: 625142448 sectors, multi 0: LBA48 NCQ
(depth 0/32)
Aug 12 09:49:10 (none) kernel: ata2.00: configured for UDMA/100
Aug 12 09:49:10 (none) kernel: scsi 0:0:0:0: Direct-Access ATA
ST3320620AS 3.AA PQ: 0 ANSI: 5
Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] 625142448 512-byte hardware
sectors (320073 MB)
Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] 625142448 512-byte hardware
sectors (320073 MB)
Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Write Protect is off
Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Aug 12 09:49:10 (none) kernel: sda: sda1
Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Attached SCSI disk
Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Aug 12 09:49:10 (none) kernel: scsi 1:0:0:0: Direct-Access ATA
ST3320620AS 3.AA PQ: 0 ANSI: 5
Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] 625142448 512-byte hardware
sectors (320073 MB)
Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Write Protect is off
Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Aug 12 09:49:10 (none) kernel: sda: sda1
Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Attached SCSI disk
Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Aug 12 09:49:10 (none) kernel: scsi 1:0:0:0: Direct-Access ATA
ST3320620AS 3.AA PQ: 0 ANSI: 5
Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] 625142448 512-byte hardware
sectors (320073 MB)
Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Write Protect is off
Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] 625142448 512-byte hardware
sectors (320073 MB)
Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Write Protect is off
Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Aug 12 09:49:10 (none) kernel: sdb: sdb1 sdb2
Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Attached SCSI disk
Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: Attached scsi generic sg1 type 0
Aug 12 09:49:10 (none) kernel: sata_via 0000:00:0f.0: version 2.3
Aug 12 09:49:10 (none) kernel: sata_via 0000:00:0f.0: PCI INT B -> GSI 20
(level, low) -> IRQ 20
Aug 12 09:49:10 (none) kernel: sata_via 0000:00:0f.0: routed to hard irq line 0
Aug 12 09:49:10 (none) kernel: scsi2 : sata_via
Aug 12 09:49:10 (none) kernel: scsi3 : sata_via
Aug 12 09:49:10 (none) kernel: ata3: SATA max UDMA/133 cmd 0x9800 ctl 0x9400
bmdma 0x8400 irq 20
Aug 12 09:49:10 (none) kernel: ata4: SATA max UDMA/133 cmd 0x9000 ctl 0x8800
bmdma 0x8408 irq 20
Aug 12 09:49:10 (none) kernel: ata3: SATA link up 1.5 Gbps (SStatus 113 SControl
300)
Aug 12 09:49:10 (none) kernel: ata3.00: ATA-7: Maxtor 6L300S0, BANC1E00, max
UDMA/133
Aug 12 09:49:10 (none) kernel: ata3.00: 586114704 sectors, multi 16: LBA48 NCQ
(not used)
Aug 12 09:49:10 (none) kernel: ata3.00: configured for UDMA/133
Aug 12 09:49:10 (none) kernel: ata4: SATA link up 1.5 Gbps (SStatus 113 SControl
300)
Aug 12 09:49:10 (none) kernel: ata4.00: ATA-7: ST3320620AS, 3.AAC, max UDMA/133
Aug 12 09:49:10 (none) kernel: ata4.00: 625134827 sectors, multi 16: LBA48 NCQ
(depth 0/32)
Aug 12 09:49:10 (none) kernel: ata4.00: configured for UDMA/133
Aug 12 09:49:10 (none) kernel: scsi 2:0:0:0: Direct-Access ATA Maxtor
6L300S0 BANC PQ: 0 ANSI: 5
Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] 586114704 512-byte hardware
sectors (300091 MB)
Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] Write Protect is off
Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] Write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] 586114704 512-byte hardware
sectors (300091 MB)
Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] Write Protect is off
Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] Write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Aug 12 09:49:10 (none) kernel: sdc: sdc1 sdc2
Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] Attached SCSI disk
Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: Attached scsi generic sg2 type 0
Aug 12 09:49:10 (none) kernel: scsi 3:0:0:0: Direct-Access ATA
ST3320620AS 3.AA PQ: 0 ANSI: 5
Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] 625134827 512-byte hardware
sectors (320069 MB)
Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] Write Protect is off
Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] 625134827 512-byte hardware
sectors (320069 MB)
Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] Write Protect is off
Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Aug 12 09:49:10 (none) kernel: sdd: sdd1 sdd2 sdd3
Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] Attached SCSI disk
Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: Attached scsi generic sg3 type 0
Aug 12 09:49:10 (none) kernel: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M]
at 0x60,0x64 irq 1,12
Aug 12 09:49:10 (none) kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
Aug 12 09:49:10 (none) kernel: serio: i8042 AUX port at 0x60,0x64 irq 12
Aug 12 09:49:10 (none) kernel: mice: PS/2 mouse device common for all mice
Aug 12 09:49:10 (none) kernel: input: AT Translated Set 2 keyboard as
/class/input/input2
Aug 12 09:49:10 (none) kernel: md: raid1 personality registered for level 1
Aug 12 09:49:10 (none) kernel: raid6: int32x1 925 MB/s
Aug 12 09:49:10 (none) kernel: raid6: int32x2 972 MB/s
Aug 12 09:49:10 (none) kernel: raid6: int32x4 789 MB/s
Aug 12 09:49:10 (none) kernel: raid6: int32x8 636 MB/s
Aug 12 09:49:10 (none) kernel: raid6: mmxx1 1753 MB/s
Aug 12 09:49:10 (none) kernel: raid6: mmxx2 3128 MB/s
Aug 12 09:49:10 (none) kernel: raid6: sse1x1 1644 MB/s
Aug 12 09:49:10 (none) kernel: raid6: sse1x2 2781 MB/s
Aug 12 09:49:10 (none) kernel: raid6: using algorithm sse1x2 (2781 MB/s)
Aug 12 09:49:10 (none) kernel: md: raid6 personality registered for level 6
Aug 12 09:49:10 (none) kernel: md: raid5 personality registered for level 5
Aug 12 09:49:10 (none) kernel: md: raid4 personality registered for level 4
Aug 12 09:49:10 (none) kernel: TCP cubic registered
Aug 12 09:49:10 (none) kernel: Using IPI Shortcut mode
Aug 12 09:49:10 (none) kernel: PM: Resume from partition /dev/sdd3
Aug 12 09:49:10 (none) kernel: PM: Checking hibernation image.
Aug 12 09:49:10 (none) kernel: PM: Resume from disk failed.
Aug 12 09:49:10 (none) kernel: input: ImExPS/2 Generic Explorer Mouse as
/class/input/input3
Aug 12 09:49:10 (none) kernel: md: Autodetecting RAID arrays.
Aug 12 09:49:10 (none) kernel: md: Scanned 2 and added 2 devices.
Aug 12 09:49:10 (none) kernel: md: autorun ...
Aug 12 09:49:10 (none) kernel: md: considering sdc2 ...
Aug 12 09:49:10 (none) kernel: md: adding sdc2 ...
Aug 12 09:49:10 (none) kernel: md: adding sdb2 ...
Aug 12 09:49:10 (none) kernel: md: created md0
Aug 12 09:49:10 (none) kernel: md: bind<sdb2>
Aug 12 09:49:10 (none) kernel: md: bind<sdc2>
Aug 12 09:49:10 (none) kernel: md: running: <sdc2><sdb2>
Aug 12 09:49:10 (none) kernel: raid1: raid set md0 active with 2 out of 2 mirrors
Aug 12 09:49:10 (none) kernel: md: ... autorun DONE.
Aug 12 09:49:10 (none) kernel: Filesystem "md0": Disabling barriers, not
supported by the underlying device
Aug 12 09:49:10 (none) kernel: XFS mounting filesystem md0
Aug 12 09:49:10 (none) kernel: Ending clean XFS mount for filesystem: md0
Aug 12 09:49:10 (none) kernel: VFS: Mounted root (xfs filesystem) readonly.
Aug 12 09:49:10 (none) kernel: Freeing unused kernel memory: 248k freed
Aug 12 09:49:10 (none) kernel: uname[892]: segfault at ffffffbf ip ffffffbf sp
bfb4b09c error 4
Aug 12 09:49:10 (none) kernel: cat[894]: segfault at ffffffbf ip ffffffbf sp
bfb121ec error 4
Aug 12 09:49:10 (none) kernel: uname[898]: segfault at ffffffbf ip ffffffbf sp
bfccc22c error 4
Aug 12 09:49:10 (none) kernel: uname[903]: segfault at ffffffbf ip ffffffbf sp
bfb8a0ec error 4
Aug 12 09:49:10 (none) kernel: uname[910]: segfault at ffffffbf ip ffffffbf sp
bfd7f2ec error 4
Aug 12 09:49:10 (none) kernel: uname[922]: segfault at ffffffbf ip ffffffbf sp
bffbe51c error 4
Aug 12 09:49:10 (none) kernel: uname[923]: segfault at ffffffbf ip ffffffbf sp
bf8dae3c error 4
Aug 12 09:49:10 (none) kernel: uname[1004]: segfault at ffffffbf ip ffffffbf sp
bff2dc8c error 4
Aug 12 09:49:10 (none) kernel: uname[1005]: segfault at ffffffbf ip ffffffbf sp
bfd86adc error 4
Aug 12 09:49:10 (none) kernel: Adding 2048276k swap on /dev/sdd3. Priority:-1
extents:1 across:2048276k
Aug 12 09:49:10 (none) kernel: Filesystem "md0": Disabling barriers, not
supported by the underlying device
Aug 12 09:49:10 (none) kernel: uname[1032]: segfault at ffffffbf ip ffffffbf sp
bffd453c error 4
Aug 12 09:49:10 (none) kernel: device-mapper: ioctl: 4.14.0-ioctl (2008-04-23)
initialised: [email protected]
Aug 12 09:49:10 (none) kernel: Filesystem "md0": XFS internal error
xfs_btree_check_sblock at line 334 of file fs/xfs/xfs_btree.c. Caller 0xc01f51fa
Aug 12 09:49:10 (none) kernel: Pid: 1113, comm: sh Not tainted 2.6.27-rc1 #10
Aug 12 09:49:10 (none) kernel: [<c01efe64>] ? xfs_cmn_err+0x34/0x60
Aug 12 09:49:10 (none) kernel: [<c01efede>] xfs_error_report+0x4e/0x50
Aug 12 09:49:10 (none) kernel: [<c01f51fa>] ? xfs_inobt_lookup+0xfa/0x3a0
Aug 12 09:49:10 (none) kernel: [<c01e29c6>] xfs_btree_check_sblock+0x56/0xd0
On Thursday, 21 of August 2008, David Greaves wrote:
> I have a desktop system that has started having problems booting up in the morning.
>
> It appears to just happen on more recent kernels.
> I was having unrelated CDROM problems with a driver in an old kernel and decided
> to test 2.6.27-rcX
> The CDROM problem is fine now.
>
> However I started having problems on -rc1. I found that the machine was hanging
> soon after booting and needed a reboot. After a reboot it would work fine for
> the rest of the day.
> When -rc3 came out I tried that and the problem still appears to be there.
>
> The normal process is now to boot to single-user, ctrl-alt-sysreq-SUB and then
> reboot to multi-user. This isn't ideal.
>
>
> If I cold boot 2.6.25.3 the problem doesn't occur.
> I will try different versions over the next few days.
>
> Sample log from a few days back. (2.6.27-rc1 I think)
>
> The problem does cause filesystem crashes so I'm cautious about messing around
> unguided.
>
> Happy to try any suggestions.
Please try 2.6.26.x and see if the problem is present in there.
Thanks,
Rafael
Rafael J. Wysocki wrote:
> Please try 2.6.26.x and see if the problem is present in there.
I'm pretty sure it is - it's my wife's machine and she's been stable on 2.6.25
for a while. I moved to 2.6.26 to fix a CDROM problem and I think that was when
I encountered this. IIRC I then tried 2.6.27-rcX to see if it had been fixed and
here we are...
I'll confirm tomorrow morning.
I wrote first in case there was any debug/instrumentation worth configuring in
as I have plenty time to recompile a kernel before shutting down tonight.
David
[Adding CCs]
[The issue is probably present in 2.6.26 too]
On Thursday, 21 of August 2008, David Greaves wrote:
> I have a desktop system that has started having problems booting up in the morning.
>
> It appears to just happen on more recent kernels.
> I was having unrelated CDROM problems with a driver in an old kernel and decided
> to test 2.6.27-rcX
> The CDROM problem is fine now.
>
> However I started having problems on -rc1. I found that the machine was hanging
> soon after booting and needed a reboot. After a reboot it would work fine for
> the rest of the day.
> When -rc3 came out I tried that and the problem still appears to be there.
>
> The normal process is now to boot to single-user, ctrl-alt-sysreq-SUB and then
> reboot to multi-user. This isn't ideal.
>
>
> If I cold boot 2.6.25.3 the problem doesn't occur.
> I will try different versions over the next few days.
>
> Sample log from a few days back. (2.6.27-rc1 I think)
>
> The problem does cause filesystem crashes so I'm cautious about messing around
> unguided.
>
> Happy to try any suggestions.
>
> David
> PS I've run memtest and it's fine.
>
>
> Aug 12 09:49:10 (none) syslogd 1.5.0#5: restart.
> Aug 12 09:49:10 (none) kernel: klogd 1.5.0#5, log source = /proc/kmsg started.
> Aug 12 09:49:10 (none) kernel: ddr 00:04:e2:cd:ac:db
> Aug 12 09:49:10 (none) kernel: via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by
> Donald Becker
> Aug 12 09:49:10 (none) kernel: via-rhine 0000:00:12.0: PCI INT A -> GSI 23
> (level, low) -> IRQ 23
> Aug 12 09:49:10 (none) kernel: eth1: VIA Rhine II at 0xdd000000,
> 00:11:2f:cd:d0:b6, IRQ 23.
> Aug 12 09:49:10 (none) kernel: eth1: MII PHY found at address 1, status 0x7849
> advertising 01e1 Link 0000.
> Aug 12 09:49:10 (none) kernel: netconsole: local port 6665
> Aug 12 09:49:10 (none) kernel: netconsole: local IP 10.0.0.74
> Aug 12 09:49:10 (none) kernel: netconsole: interface eth0
> Aug 12 09:49:10 (none) kernel: netconsole: remote port 6666
> Aug 12 09:49:10 (none) kernel: netconsole: remote IP 10.0.0.7
> Aug 12 09:49:10 (none) kernel: netconsole: remote ethernet address 00:13:20:55:b6:60
> Aug 12 09:49:10 (none) kernel: netconsole: device eth0 not up yet, forcing it
> Aug 12 09:49:10 (none) kernel: skge eth0: enabling interface
> Aug 12 09:49:10 (none) kernel: skge eth0: Link is up at 1000 Mbps, full duplex,
> flow control both
> Aug 12 09:49:10 (none) kernel: console [netcon0] enabled
> Aug 12 09:49:10 (none) kernel: netconsole: network logging started
> Aug 12 09:49:10 (none) kernel: Driver 'sd' needs updating - please use bus_type
> methods
> Aug 12 09:49:10 (none) kernel: Driver 'sr' needs updating - please use bus_type
> methods
> Aug 12 09:49:10 (none) kernel: sata_sil 0000:00:0a.0: version 2.3
> Aug 12 09:49:10 (none) kernel: sata_sil 0000:00:0a.0: PCI INT A -> GSI 16
> (level, low) -> IRQ 16
> Aug 12 09:49:10 (none) kernel: scsi0 : sata_sil
> Aug 12 09:49:10 (none) kernel: scsi1 : sata_sil
> Aug 12 09:49:10 (none) kernel: ata1: SATA max UDMA/100 mmio m512@0xde800000 tf
> 0xde800080 irq 16
> Aug 12 09:49:10 (none) kernel: ata2: SATA max UDMA/100 mmio m512@0xde800000 tf
> 0xde8000c0 irq 16
> Aug 12 09:49:10 (none) kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl
> 310)
> Aug 12 09:49:10 (none) kernel: ata1.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
> Aug 12 09:49:10 (none) kernel: ata1.00: 625142448 sectors, multi 0: LBA48 NCQ
> (depth 0/32)
> Aug 12 09:49:10 (none) kernel: ata1.00: configured for UDMA/100
> Aug 12 09:49:10 (none) kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl
> 310)
> Aug 12 09:49:10 (none) kernel: ata2.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133
> Aug 12 09:49:10 (none) kernel: ata2.00: 625142448 sectors, multi 0: LBA48 NCQ
> (depth 0/32)
> Aug 12 09:49:10 (none) kernel: ata2.00: configured for UDMA/100
> Aug 12 09:49:10 (none) kernel: scsi 0:0:0:0: Direct-Access ATA
> ST3320620AS 3.AA PQ: 0 ANSI: 5
> Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] 625142448 512-byte hardware
> sectors (320073 MB)
> Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Write Protect is off
> Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Write cache: enabled, read
> cache: enabled, doesn't support DPO or FUA
> Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] 625142448 512-byte hardware
> sectors (320073 MB)
> Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Write Protect is off
> Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Write cache: enabled, read
> cache: enabled, doesn't support DPO or FUA
> Aug 12 09:49:10 (none) kernel: sda: sda1
> Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Attached SCSI disk
> Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
> Aug 12 09:49:10 (none) kernel: scsi 1:0:0:0: Direct-Access ATA
> ST3320620AS 3.AA PQ: 0 ANSI: 5
> Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] 625142448 512-byte hardware
> sectors (320073 MB)
> Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Write Protect is off
> Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
> Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Write cache: enabled, read
> cache: enabled, doesn't support DPO or FUA
> Aug 12 09:49:10 (none) kernel: sda: sda1
> Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: [sda] Attached SCSI disk
> Aug 12 09:49:10 (none) kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
> Aug 12 09:49:10 (none) kernel: scsi 1:0:0:0: Direct-Access ATA
> ST3320620AS 3.AA PQ: 0 ANSI: 5
> Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] 625142448 512-byte hardware
> sectors (320073 MB)
> Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Write Protect is off
> Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
> Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read
> cache: enabled, doesn't support DPO or FUA
> Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] 625142448 512-byte hardware
> sectors (320073 MB)
> Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Write Protect is off
> Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
> Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read
> cache: enabled, doesn't support DPO or FUA
> Aug 12 09:49:10 (none) kernel: sdb: sdb1 sdb2
> Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: [sdb] Attached SCSI disk
> Aug 12 09:49:10 (none) kernel: sd 1:0:0:0: Attached scsi generic sg1 type 0
> Aug 12 09:49:10 (none) kernel: sata_via 0000:00:0f.0: version 2.3
> Aug 12 09:49:10 (none) kernel: sata_via 0000:00:0f.0: PCI INT B -> GSI 20
> (level, low) -> IRQ 20
> Aug 12 09:49:10 (none) kernel: sata_via 0000:00:0f.0: routed to hard irq line 0
> Aug 12 09:49:10 (none) kernel: scsi2 : sata_via
> Aug 12 09:49:10 (none) kernel: scsi3 : sata_via
> Aug 12 09:49:10 (none) kernel: ata3: SATA max UDMA/133 cmd 0x9800 ctl 0x9400
> bmdma 0x8400 irq 20
> Aug 12 09:49:10 (none) kernel: ata4: SATA max UDMA/133 cmd 0x9000 ctl 0x8800
> bmdma 0x8408 irq 20
> Aug 12 09:49:10 (none) kernel: ata3: SATA link up 1.5 Gbps (SStatus 113 SControl
> 300)
> Aug 12 09:49:10 (none) kernel: ata3.00: ATA-7: Maxtor 6L300S0, BANC1E00, max
> UDMA/133
> Aug 12 09:49:10 (none) kernel: ata3.00: 586114704 sectors, multi 16: LBA48 NCQ
> (not used)
> Aug 12 09:49:10 (none) kernel: ata3.00: configured for UDMA/133
> Aug 12 09:49:10 (none) kernel: ata4: SATA link up 1.5 Gbps (SStatus 113 SControl
> 300)
> Aug 12 09:49:10 (none) kernel: ata4.00: ATA-7: ST3320620AS, 3.AAC, max UDMA/133
> Aug 12 09:49:10 (none) kernel: ata4.00: 625134827 sectors, multi 16: LBA48 NCQ
> (depth 0/32)
> Aug 12 09:49:10 (none) kernel: ata4.00: configured for UDMA/133
> Aug 12 09:49:10 (none) kernel: scsi 2:0:0:0: Direct-Access ATA Maxtor
> 6L300S0 BANC PQ: 0 ANSI: 5
> Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] 586114704 512-byte hardware
> sectors (300091 MB)
> Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] Write Protect is off
> Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
> Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] Write cache: enabled, read
> cache: enabled, doesn't support DPO or FUA
> Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] 586114704 512-byte hardware
> sectors (300091 MB)
> Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] Write Protect is off
> Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
> Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] Write cache: enabled, read
> cache: enabled, doesn't support DPO or FUA
> Aug 12 09:49:10 (none) kernel: sdc: sdc1 sdc2
> Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: [sdc] Attached SCSI disk
> Aug 12 09:49:10 (none) kernel: sd 2:0:0:0: Attached scsi generic sg2 type 0
> Aug 12 09:49:10 (none) kernel: scsi 3:0:0:0: Direct-Access ATA
> ST3320620AS 3.AA PQ: 0 ANSI: 5
> Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] 625134827 512-byte hardware
> sectors (320069 MB)
> Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] Write Protect is off
> Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
> Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read
> cache: enabled, doesn't support DPO or FUA
> Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] 625134827 512-byte hardware
> sectors (320069 MB)
> Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] Write Protect is off
> Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
> Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] Write cache: enabled, read
> cache: enabled, doesn't support DPO or FUA
> Aug 12 09:49:10 (none) kernel: sdd: sdd1 sdd2 sdd3
> Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: [sdd] Attached SCSI disk
> Aug 12 09:49:10 (none) kernel: sd 3:0:0:0: Attached scsi generic sg3 type 0
> Aug 12 09:49:10 (none) kernel: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M]
> at 0x60,0x64 irq 1,12
> Aug 12 09:49:10 (none) kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
> Aug 12 09:49:10 (none) kernel: serio: i8042 AUX port at 0x60,0x64 irq 12
> Aug 12 09:49:10 (none) kernel: mice: PS/2 mouse device common for all mice
> Aug 12 09:49:10 (none) kernel: input: AT Translated Set 2 keyboard as
> /class/input/input2
> Aug 12 09:49:10 (none) kernel: md: raid1 personality registered for level 1
> Aug 12 09:49:10 (none) kernel: raid6: int32x1 925 MB/s
> Aug 12 09:49:10 (none) kernel: raid6: int32x2 972 MB/s
> Aug 12 09:49:10 (none) kernel: raid6: int32x4 789 MB/s
> Aug 12 09:49:10 (none) kernel: raid6: int32x8 636 MB/s
> Aug 12 09:49:10 (none) kernel: raid6: mmxx1 1753 MB/s
> Aug 12 09:49:10 (none) kernel: raid6: mmxx2 3128 MB/s
> Aug 12 09:49:10 (none) kernel: raid6: sse1x1 1644 MB/s
> Aug 12 09:49:10 (none) kernel: raid6: sse1x2 2781 MB/s
> Aug 12 09:49:10 (none) kernel: raid6: using algorithm sse1x2 (2781 MB/s)
> Aug 12 09:49:10 (none) kernel: md: raid6 personality registered for level 6
> Aug 12 09:49:10 (none) kernel: md: raid5 personality registered for level 5
> Aug 12 09:49:10 (none) kernel: md: raid4 personality registered for level 4
> Aug 12 09:49:10 (none) kernel: TCP cubic registered
> Aug 12 09:49:10 (none) kernel: Using IPI Shortcut mode
> Aug 12 09:49:10 (none) kernel: PM: Resume from partition /dev/sdd3
> Aug 12 09:49:10 (none) kernel: PM: Checking hibernation image.
> Aug 12 09:49:10 (none) kernel: PM: Resume from disk failed.
> Aug 12 09:49:10 (none) kernel: input: ImExPS/2 Generic Explorer Mouse as
> /class/input/input3
> Aug 12 09:49:10 (none) kernel: md: Autodetecting RAID arrays.
> Aug 12 09:49:10 (none) kernel: md: Scanned 2 and added 2 devices.
> Aug 12 09:49:10 (none) kernel: md: autorun ...
> Aug 12 09:49:10 (none) kernel: md: considering sdc2 ...
> Aug 12 09:49:10 (none) kernel: md: adding sdc2 ...
> Aug 12 09:49:10 (none) kernel: md: adding sdb2 ...
> Aug 12 09:49:10 (none) kernel: md: created md0
> Aug 12 09:49:10 (none) kernel: md: bind<sdb2>
> Aug 12 09:49:10 (none) kernel: md: bind<sdc2>
> Aug 12 09:49:10 (none) kernel: md: running: <sdc2><sdb2>
> Aug 12 09:49:10 (none) kernel: raid1: raid set md0 active with 2 out of 2 mirrors
> Aug 12 09:49:10 (none) kernel: md: ... autorun DONE.
> Aug 12 09:49:10 (none) kernel: Filesystem "md0": Disabling barriers, not
> supported by the underlying device
> Aug 12 09:49:10 (none) kernel: XFS mounting filesystem md0
> Aug 12 09:49:10 (none) kernel: Ending clean XFS mount for filesystem: md0
> Aug 12 09:49:10 (none) kernel: VFS: Mounted root (xfs filesystem) readonly.
> Aug 12 09:49:10 (none) kernel: Freeing unused kernel memory: 248k freed
> Aug 12 09:49:10 (none) kernel: uname[892]: segfault at ffffffbf ip ffffffbf sp
> bfb4b09c error 4
> Aug 12 09:49:10 (none) kernel: cat[894]: segfault at ffffffbf ip ffffffbf sp
> bfb121ec error 4
> Aug 12 09:49:10 (none) kernel: uname[898]: segfault at ffffffbf ip ffffffbf sp
> bfccc22c error 4
> Aug 12 09:49:10 (none) kernel: uname[903]: segfault at ffffffbf ip ffffffbf sp
> bfb8a0ec error 4
> Aug 12 09:49:10 (none) kernel: uname[910]: segfault at ffffffbf ip ffffffbf sp
> bfd7f2ec error 4
> Aug 12 09:49:10 (none) kernel: uname[922]: segfault at ffffffbf ip ffffffbf sp
> bffbe51c error 4
> Aug 12 09:49:10 (none) kernel: uname[923]: segfault at ffffffbf ip ffffffbf sp
> bf8dae3c error 4
> Aug 12 09:49:10 (none) kernel: uname[1004]: segfault at ffffffbf ip ffffffbf sp
> bff2dc8c error 4
> Aug 12 09:49:10 (none) kernel: uname[1005]: segfault at ffffffbf ip ffffffbf sp
> bfd86adc error 4
> Aug 12 09:49:10 (none) kernel: Adding 2048276k swap on /dev/sdd3. Priority:-1
> extents:1 across:2048276k
> Aug 12 09:49:10 (none) kernel: Filesystem "md0": Disabling barriers, not
> supported by the underlying device
> Aug 12 09:49:10 (none) kernel: uname[1032]: segfault at ffffffbf ip ffffffbf sp
> bffd453c error 4
> Aug 12 09:49:10 (none) kernel: device-mapper: ioctl: 4.14.0-ioctl (2008-04-23)
> initialised: [email protected]
> Aug 12 09:49:10 (none) kernel: Filesystem "md0": XFS internal error
> xfs_btree_check_sblock at line 334 of file fs/xfs/xfs_btree.c. Caller 0xc01f51fa
> Aug 12 09:49:10 (none) kernel: Pid: 1113, comm: sh Not tainted 2.6.27-rc1 #10
> Aug 12 09:49:10 (none) kernel: [<c01efe64>] ? xfs_cmn_err+0x34/0x60
> Aug 12 09:49:10 (none) kernel: [<c01efede>] xfs_error_report+0x4e/0x50
> Aug 12 09:49:10 (none) kernel: [<c01f51fa>] ? xfs_inobt_lookup+0xfa/0x3a0
> Aug 12 09:49:10 (none) kernel: [<c01e29c6>] xfs_btree_check_sblock+0x56/0xd0
Rafael J. Wysocki wrote:
> [Adding CCs]
>
> [The issue is probably present in 2.6.26 too]
>
> On Thursday, 21 of August 2008, David Greaves wrote:
>> I have a desktop system that has started having problems booting up in the morning.
>>
>> It appears to just happen on more recent kernels.
>> I was having unrelated CDROM problems with a driver in an old kernel and decided
>> to test 2.6.27-rcX
>> The CDROM problem is fine now.
>>
>> However I started having problems on -rc1. I found that the machine was hanging
>> soon after booting and needed a reboot. After a reboot it would work fine for
>> the rest of the day.
>> When -rc3 came out I tried that and the problem still appears to be there.
>>
>> The normal process is now to boot to single-user, ctrl-alt-sysreq-SUB and then
>> reboot to multi-user. This isn't ideal.
>>
>>
>> If I cold boot 2.6.25.3 the problem doesn't occur.
>> I will try different versions over the next few days.
As promised, I tried 2.6.26.3 this morning and didn't have the problem. I will
try again a few times to confirm.
Nb Although the log had an XFS failure, I think the real issue is the segfaults;
I think XFS is a casuality, not a cause. Th problem almost always results in an
XFS crash at some point - but usually preceded by many segfaults in random binaries.
David
Rafael J. Wysocki wrote:
> [Adding CCs]
>
> [The issue is probably present in 2.6.26 too]
Yes, below is a netconsole boot of 2.26.6.3
I cold booted - lots of segfaults. I then did a ctrl-Alt-SysRq-S-U-B to a warm
boot. No segfaults
(lots of #### mark the split)
I've just started 2.6.25.14 building for tomorrow to confirm how far back it
goes. (I'm 99% sure 2.6.25 is OK)
David
elm:~# netcat -u -l -p 6666
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata2.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133
ata2.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdb: sdb1 sdb2
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg1 type 0
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
sata_via 0000:00:0f.0: routed to hard irq line 0
scsi2 : sata_via
scsi3 : sata_via
ata3: SATA max UDMA/133 cmd 0x9800 ctl 0x9400 bmdma 0x8400 irq 20
ata4: SATA max UDMA/133 cmd 0x9000 ctl 0x8800 bmdma 0x8408 irq 20
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATA-7: Maxtor 6L300S0, BANC1E00, max UDMA/133
ata3.00: 586114704 sectors, multi 16: LBA48 NCQ (not used)
ata3.00: configured for UDMA/133
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATA-7: ST3320620AS, 3.AAC, max UDMA/133
ata4.00: 625134827 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata4.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA Maxtor 6L300S0 BANC PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 586114704 512-byte hardware sectors (300091 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sd 2:0:0:0: [sdc] 586114704 512-byte hardware sectors (300091 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdc: sdc1 sdc2
sd 2:0:0:0: [sdc] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg2 type 0
scsi 3:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 3:0:0:0: [sdd] 625134827 512-byte hardware sectors (320069 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sd 3:0:0:0: [sdd] 625134827 512-byte hardware sectors (320069 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdd: sdd1 sdd2 sdd3
sd 3:0:0:0: [sdd] Attached SCSI disk
sd 3:0:0:0: Attached scsi generic sg3 type 0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input2
md: raid1 personality registered for level 1
raid6: int32x1 925 MB/s
raid6: int32x2 972 MB/s
raid6: int32x4 777 MB/s
raid6: int32x8 601 MB/s
raid6: mmxx1 1730 MB/s
raid6: mmxx2 3105 MB/s
raid6: sse1x1 1644 MB/s
raid6: sse1x2 2789 MB/s
raid6: using algorithm sse1x2 (2789 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
TCP cubic registered
Using IPI Shortcut mode
input: ImExPS/2 Generic Explorer Mouse as /class/input/input3
md: Autodetecting RAID arrays.
md: Scanned 2 and added 2 devices.
md: autorun ...
md: considering sdc2 ...
md: adding sdc2 ...
md: adding sdb2 ...
md: created md0
md: bind<sdb2>
md: bind<sdc2>
md: running: <sdc2><sdb2>
raid1: raid set md0 active with 2 out of 2 mirrors
md: ... autorun DONE.
Filesystem "md0": Disabling barriers, not supported by the underlying device
XFS mounting filesystem md0
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 228k freed
Linux agpgart interface v0.103
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 32M @ 0xfc000000
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
scsi4 : pata_via
scsi5 : pata_via
ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x7800 irq 14
ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x7808 irq 15
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ata5.00: ATAPI: PLEXTOR DVDR PX-708A, 1.02, max UDMA/33
ata5.01: ATAPI: TSSTcorpCD/DVDW SH-W162C, TS10, max UDMA/33
ata5.00: configured for UDMA/33
ata5.01: configured for UDMA/33
ata6.00: ATAPI: PLEXTOR CD-R PX-W2410A, 1.02, max UDMA/33
ata6.00: configured for UDMA/33
scsi 4:0:0:0: CD-ROM PLEXTOR DVDR PX-708A 1.02 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 4:0:0:0: Attached scsi generic sg4 type 5
scsi 4:0:1:0: CD-ROM TSSTcorp CD/DVDW SH-W162C TS10 PQ: 0 ANSI: 5
sr1: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
sr 4:0:1:0: Attached scsi generic sg5 type 5
scsi 5:0:0:0: CD-ROM PLEXTOR CD-R PX-W2410A 1.02 PQ: 0 ANSI: 5
sr2: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
sr 5:0:0:0: Attached scsi generic sg6 type 5
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 21, io base 0x00007400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 21, io base 0x00007000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 21, io base 0x00006800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 21, io base 0x00006400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 21, io mem 0xdd800000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 22
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
Adding 2048276k swap on /dev/sdd3. Priority:-1 extents:1 across:2048276k
Filesystem "md0": Disabling barriers, not supported by the underlying device
device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: [email protected]
md: md1 stopped.
md: bind<sdc1>
md: bind<sdb1>
md: bind<sda1>
md: bind<sdd1>
raid5: device sdd1 operational as raid disk 0
raid5: device sda1 operational as raid disk 3
raid5: device sdb1 operational as raid disk 2
raid5: device sdc1 operational as raid disk 1
raid5: allocated 4203kB for md1
raid5: raid level 5 set md1 active with 4 out of 4 devices, algorithm 2
RAID5 conf printout:
--- rd:4 wd:4
disk 0, o:1, dev:sdd1
disk 1, o:1, dev:sdc1
disk 2, o:1, dev:sdb1
disk 3, o:1, dev:sda1
md1: bitmap initialized from disk: read 9/9 pages, set 0 bits
created bitmap (135 pages) for device md1
Filesystem "dm-0": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-0
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
acpid[2800]: segfault at ffffffbf ip ffffffbf sp bfe7839c error 4
warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
Installing knfsd (copyright (C) 1996 [email protected]).
env[3550]: segfault at ffffffbf ip ffffffbf sp bf92962c error 4
env[3551]: segfault at ffffffbf ip ffffffbf sp bff9648c error 4
env[3558]: segfault at ffffffbf ip ffffffbf sp bfb3683c error 4
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized radeon 1.29.0 20080528 on minor 0
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 1 usecs
kdm_greet[3710]: segfault at ffffffbf ip ffffffbf sp bfc5a3ac error 4
Filesystem "md0": XFS internal error xfs_btree_check_lblock at line 213 of file
fs/xfs/xfs_btree.c. Caller 0xc01ddfa1
Pid: 161, comm: pdflush Not tainted 2.6.26.3 #12
[<c01ee734>] ? xfs_cmn_err+0x34/0x60
[<c01ee7ae>] xfs_error_report+0x4e/0x50
[<c01ddfa1>] ? xfs_bmbt_lookup+0x2c1/0x4f0
[<c01e140d>] xfs_btree_check_lblock+0x4d/0x150
[<c01ddfa1>] ? xfs_bmbt_lookup+0x2c1/0x4f0
[<c01ddfa1>] xfs_bmbt_lookup+0x2c1/0x4f0
[<c01de225>] xfs_bmbt_lookup_eq+0x25/0x30
[<c01d5faf>] xfs_bmap_add_extent_delay_real+0x72f/0x11b0
[<c020ff30>] ? xfs_trans_log_buf+0x70/0x80
[<c01c5f12>] ? xfs_alloc_search_busy+0xb2/0xe0
[<c01c83be>] ? xfs_alloc_vextent+0x33e/0x450
[<c01d79a3>] ? xfs_bmap_btalloc+0x743/0xa80
[<c01f6899>] ? xfs_iext_bno_to_ext+0x89/0x1a0
[<c0156d69>] ? get_page_from_freelist+0x239/0x4e0
[<c01d6e57>] xfs_bmap_add_extent+0x427/0x450
[<c01e0d98>] ? xfs_btree_init_cursor+0x28/0x1d0
[<c01db022>] xfs_bmapi+0xd12/0x12e0
[<c0218d20>] ? kmem_zone_alloc+0x80/0xc0
[<c01fcf44>] xfs_iomap_write_allocate+0x254/0x3e0
[<c020f5a8>] ? xfs_trans_unlocked_item+0x38/0x50
[<c01fdf87>] xfs_iomap+0x327/0x370
[<c023277d>] ? submit_bio+0x6d/0x110
[<c0219b4e>] xfs_map_blocks+0x3e/0x90
[<c021a97a>] xfs_page_state_convert+0x41a/0x810
[<c0231d4a>] ? blk_done_softirq+0x5a/0x70
[<c021b05a>] xfs_vm_writepage+0x5a/0xf0
[<c015769b>] __writepage+0xb/0x40
[<c015811e>] write_cache_pages+0x17e/0x330
[<c0157690>] ? __writepage+0x0/0x40
[<c0220e27>] ? xfs_bdstrat_cb+0x37/0x70
[<c021ce62>] ? xfs_buf_iostart+0x42/0xb0
[<c01f93e8>] ? xfs_iflush+0x288/0x2f0
[<c01582f3>] generic_writepages+0x23/0x30
[<c021afc5>] xfs_vm_writepages+0x55/0x70
[<c021af70>] ? xfs_vm_writepages+0x0/0x70
[<c015832e>] do_writepages+0x2e/0x50
[<c0194ee3>] __writeback_single_inode+0x93/0x490
[<f895d1a3>] ? dm_table_any_congested+0x33/0x80 [dm_mod]
[<c02e3b6c>] ? raid1_congested+0x7c/0xb0
[<c01957a2>] sync_sb_inodes+0x242/0x390
[<c0211f0d>] ? xfs_sync+0x3d/0x60
[<c0195b1e>] writeback_inodes+0x5e/0x140
[<c015845b>] wb_kupdate+0x7b/0xf0
[<c0158d80>] ? pdflush+0x0/0x210
[<c0158e90>] pdflush+0x110/0x210
[<c01583e0>] ? wb_kupdate+0x0/0xf0
[<c013572a>] kthread+0x3a/0x70
[<c01356f0>] ? kthread+0x0/0x70
[<c0103d1f>] kernel_thread_helper+0x7/0x18
=======================
Filesystem "md0": XFS internal error xfs_trans_cancel at line 1163 of file
fs/xfs/xfs_trans.c. Caller 0xc01fd04c
Pid: 161, comm: pdflush Not tainted 2.6.26.3 #12
[<c01ee734>] ? xfs_cmn_err+0x34/0x60
[<c01ee7ae>] xfs_error_report+0x4e/0x50
[<c01fd04c>] ? xfs_iomap_write_allocate+0x35c/0x3e0
[<c020e3ea>] xfs_trans_cancel+0xca/0xf0
[<c01fd04c>] ? xfs_iomap_write_allocate+0x35c/0x3e0
[<c01fd04c>] xfs_iomap_write_allocate+0x35c/0x3e0
[<c020f5a8>] ? xfs_trans_unlocked_item+0x38/0x50
[<c01fdf87>] xfs_iomap+0x327/0x370
[<c023277d>] ? submit_bio+0x6d/0x110
[<c0219b4e>] xfs_map_blocks+0x3e/0x90
[<c021a97a>] xfs_page_state_convert+0x41a/0x810
[<c0231d4a>] ? blk_done_softirq+0x5a/0x70
[<c021b05a>] xfs_vm_writepage+0x5a/0xf0
[<c015769b>] __writepage+0xb/0x40
[<c015811e>] write_cache_pages+0x17e/0x330
[<c0157690>] ? __writepage+0x0/0x40
[<c0220e27>] ? xfs_bdstrat_cb+0x37/0x70
[<c021ce62>] ? xfs_buf_iostart+0x42/0xb0
[<c01f93e8>] ? xfs_iflush+0x288/0x2f0
[<c01582f3>] generic_writepages+0x23/0x30
[<c021afc5>] xfs_vm_writepages+0x55/0x70
[<c021af70>] ? xfs_vm_writepages+0x0/0x70
[<c015832e>] do_writepages+0x2e/0x50
[<c0194ee3>] __writeback_single_inode+0x93/0x490
[<f895d1a3>] ? dm_table_any_congested+0x33/0x80 [dm_mod]
[<c02e3b6c>] ? raid1_congested+0x7c/0xb0
[<c01957a2>] sync_sb_inodes+0x242/0x390
[<c0211f0d>] ? xfs_sync+0x3d/0x60
[<c0195b1e>] writeback_inodes+0x5e/0x140
[<c015845b>] wb_kupdate+0x7b/0xf0
[<c0158d80>] ? pdflush+0x0/0x210
[<c0158e90>] pdflush+0x110/0x210
[<c01583e0>] ? wb_kupdate+0x0/0xf0
[<c013572a>] kthread+0x3a/0x70
[<c01356f0>] ? kthread+0x0/0x70
[<c0103d1f>] kernel_thread_helper+0x7/0x18
=======================
xfs_force_shutdown(md0,0x8) called from line 1164 of file fs/xfs/xfs_trans.c.
Return address = 0xc020e402
Filesystem "md0": Corruption of in-memory data detected. Shutting down
filesystem: md0
Please umount the filesystem, and rectify the problem(s)
SysRq : Emergency Sync
Filesystem "md0": xfs_log_force: error 5 returned.
Emergency Sync complete
SysRq : Emergency Remount R/O
Filesystem "md0": xfs_log_force: error 5 returned.
Filesystem "md0": xfs_log_force: error 5 returned.
xfs_force_shutdown(md0,0x1) called from line 420 of file fs/xfs/xfs_rw.c.
Return address = 0xc021880c
Filesystem "md0": xfs_log_force: error 5 returned.
Filesystem "md0": xfs_log_force: error 5 returned.
xfs_force_shutdown(md0,0x1) called from line 420 of file fs/xfs/xfs_rw.c.
Return address = 0xc021880c
Filesystem "md0": xfs_log_force: error 5 returned.
Filesystem "md0": xfs_log_force: error 5 returned.
Emergency Remount complete
SysRq : Resetting
##################################################################################
##################################################################################
##################################################################################
##################################################################################
##################################################################################
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata2.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133
ata2.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdb: sdb1 sdb2
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg1 type 0
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
sata_via 0000:00:0f.0: routed to hard irq line 0
scsi2 : sata_via
scsi3 : sata_via
ata3: SATA max UDMA/133 cmd 0x9800 ctl 0x9400 bmdma 0x8400 irq 20
ata4: SATA max UDMA/133 cmd 0x9000 ctl 0x8800 bmdma 0x8408 irq 20
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATA-7: Maxtor 6L300S0, BANC1E00, max UDMA/133
ata3.00: 586114704 sectors, multi 16: LBA48 NCQ (not used)
ata3.00: configured for UDMA/133
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATA-7: ST3320620AS, 3.AAC, max UDMA/133
ata4.00: 625134827 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata4.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA Maxtor 6L300S0 BANC PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 586114704 512-byte hardware sectors (300091 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sd 2:0:0:0: [sdc] 586114704 512-byte hardware sectors (300091 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdc: sdc1 sdc2
sd 2:0:0:0: [sdc] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg2 type 0
scsi 3:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
sd 3:0:0:0: [sdd] 625134827 512-byte hardware sectors (320069 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sd 3:0:0:0: [sdd] 625134827 512-byte hardware sectors (320069 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdd: sdd1 sdd2 sdd3
sd 3:0:0:0: [sdd] Attached SCSI disk
sd 3:0:0:0: Attached scsi generic sg3 type 0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input2
md: raid1 personality registered for level 1
raid6: int32x1 925 MB/s
raid6: int32x2 972 MB/s
raid6: int32x4 777 MB/s
raid6: int32x8 601 MB/s
raid6: mmxx1 1730 MB/s
raid6: mmxx2 3105 MB/s
raid6: sse1x1 1644 MB/s
raid6: sse1x2 2789 MB/s
raid6: using algorithm sse1x2 (2789 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
TCP cubic registered
Using IPI Shortcut mode
input: ImExPS/2 Generic Explorer Mouse as /class/input/input3
md: Autodetecting RAID arrays.
md: Scanned 2 and added 2 devices.
md: autorun ...
md: considering sdc2 ...
md: adding sdc2 ...
md: adding sdb2 ...
md: created md0
md: bind<sdb2>
md: bind<sdc2>
md: running: <sdc2><sdb2>
raid1: raid set md0 active with 2 out of 2 mirrors
md: ... autorun DONE.
Filesystem "md0": Disabling barriers, not supported by the underlying device
XFS mounting filesystem md0
Starting XFS recovery on filesystem: md0 (logdev: internal)
Ending XFS recovery on filesystem: md0 (logdev: internal)
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 228k freed
Linux agpgart interface v0.103
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 32M @ 0xfc000000
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
scsi4 : pata_via
scsi5 : pata_via
ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x7800 irq 14
ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x7808 irq 15
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ata5.00: ATAPI: PLEXTOR DVDR PX-708A, 1.02, max UDMA/33
ata5.01: ATAPI: TSSTcorpCD/DVDW SH-W162C, TS10, max UDMA/33
ata5.00: configured for UDMA/33
ata5.01: configured for UDMA/33
ata6.00: ATAPI: PLEXTOR CD-R PX-W2410A, 1.02, max UDMA/33
ata6.00: configured for UDMA/33
scsi 4:0:0:0: CD-ROM PLEXTOR DVDR PX-708A 1.02 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 4:0:0:0: Attached scsi generic sg4 type 5
scsi 4:0:1:0: CD-ROM TSSTcorp CD/DVDW SH-W162C TS10 PQ: 0 ANSI: 5
sr1: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
sr 4:0:1:0: Attached scsi generic sg5 type 5
scsi 5:0:0:0: CD-ROM PLEXTOR CD-R PX-W2410A 1.02 PQ: 0 ANSI: 5
sr2: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
sr 5:0:0:0: Attached scsi generic sg6 type 5
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 21, io base 0x00007400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 21, io base 0x00007000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 21, io base 0x00006800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 21, io base 0x00006400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 21, io mem 0xdd800000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 22
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
Adding 2048276k swap on /dev/sdd3. Priority:-1 extents:1 across:2048276k
Filesystem "md0": Disabling barriers, not supported by the underlying device
device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: [email protected]
md: md1 stopped.
md: bind<sdc1>
md: bind<sdb1>
md: bind<sda1>
md: bind<sdd1>
raid5: device sdd1 operational as raid disk 0
raid5: device sda1 operational as raid disk 3
raid5: device sdb1 operational as raid disk 2
raid5: device sdc1 operational as raid disk 1
raid5: allocated 4203kB for md1
raid5: raid level 5 set md1 active with 4 out of 4 devices, algorithm 2
RAID5 conf printout:
--- rd:4 wd:4
disk 0, o:1, dev:sdd1
disk 1, o:1, dev:sdc1
disk 2, o:1, dev:sdb1
disk 3, o:1, dev:sda1
md1: bitmap initialized from disk: read 9/9 pages, set 2 bits
created bitmap (135 pages) for device md1
Filesystem "dm-0": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-0
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
Installing knfsd (copyright (C) 1996 [email protected]).
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized radeon 1.29.0 20080528 on minor 0
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 1 usecs