Hi,
I recently needed some more space and bought a Deskstar 7K1000.B for my server.
The motherboard is old, and did not have SATA port, so I added a
VT6421 PCI SATA controller.
I was first able to run cfdisk to setup the partition table.
The I tried to run hdparm -tT on it (mkfs.ext4 did'nt work either) but
I doesn't work (I/O errors).
Note that I dowgraded the disk to SATA I using hitachi tools. Also
tested the disk on a motherboard with SATA and it seems ok.
Any idea ?
Thanks
lspci + dmesg below:
00:0f.0 RAID bus controller: VIA Technologies, Inc. VT6421 IDE RAID
Controller (rev 50)
Subsystem: VIA Technologies, Inc. VT6421 IDE RAID Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at d000 [size=16]
Region 1: I/O ports at b800 [size=16]
Region 2: I/O ports at b400 [size=16]
Region 3: I/O ports at b000 [size=16]
Region 4: I/O ports at a800 [size=32]
Region 5: I/O ports at a400 [size=256]
[virtual] Expansion ROM at 40010000 [disabled] [size=64K]
Capabilities: [e0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: sata_via
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1916.734 MHz processor.
[ 0.001217] Console: colour VGA+ 80x25
[ 0.001220] console [tty0] enabled
[ 0.004000] Calibrating delay loop (skipped), value calculated
using timer frequency.. 3833.46 BogoMIPS (lpj=7666936)
[ 0.004000] Mount-cache hash table entries: 512
[ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
[ 0.004000] CPU: L2 Cache: 512K (64 bytes/line)
[ 0.004000] mce: CPU supports 4 MCE banks
[ 0.004000] Checking 'hlt' instruction... OK.
[ 0.016354] SMP alternatives: switching to UP code
[ 0.019735] Freeing SMP alternatives: 15k freed
[ 0.019815] ACPI: Core revision 20090521
[ 0.029040] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.068811] CPU0: AMD Athlon(TM) XP 2600+ stepping 00
[ 0.072001] Brought up 1 CPUs
[ 0.072001] Total of 1 processors activated (3833.46 BogoMIPS).
[ 0.072001] NET: Registered protocol family 16
[ 0.072001] ACPI: bus type pci registered
[ 0.072001] PCI: Using configuration type 1 for base access
[ 0.072176] bio: create slab <bio-0> at 0
[ 0.072820] ACPI: EC: Look up EC in DSDT
[ 0.081700] ACPI: Interpreter enabled
[ 0.081772] ACPI: (supports S0 S5)
[ 0.081916] ACPI: Using IOAPIC for interrupt routing
[ 0.098369] ACPI: No dock devices found.
[ 0.098598] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.098749] pci 0000:00:00.0: reg 10 32bit mmio:
[0xf8000000-0xfbffffff]
[ 0.098833] pci 0000:00:01.0: supports D1
[ 0.098873] pci 0000:00:0d.0: reg 10 io port: [0xd800-0xd8ff]
[ 0.098880] pci 0000:00:0d.0: reg 14 32bit mmio:
[0xed800000-0xed8000ff]
[ 0.098901] pci 0000:00:0d.0: reg 30 32bit mmio:
[0x000000-0x00ffff]
[ 0.098917] pci 0000:00:0d.0: supports D1 D2
[ 0.098920] pci 0000:00:0d.0: PME# supported from D1 D2 D3hot
D3cold
[ 0.098996] pci 0000:00:0d.0: PME# disabled
[ 0.099093] pci 0000:00:0e.0: reg 10 io port: [0xd400-0xd4ff]
[ 0.099099] pci 0000:00:0e.0: reg 14 32bit mmio:
[0xed000000-0xed0000ff]
[ 0.099133] pci 0000:00:0e.0: supports D1 D2
[ 0.099135] pci 0000:00:0e.0: PME# supported from D1 D2 D3hot
D3cold
[ 0.099210] pci 0000:00:0e.0: PME# disabled
[ 0.099309] pci 0000:00:0f.0: reg 10 io port: [0xd000-0xd00f]
[ 0.099315] pci 0000:00:0f.0: reg 14 io port: [0xb800-0xb80f]
[ 0.099322] pci 0000:00:0f.0: reg 18 io port: [0xb400-0xb40f]
[ 0.099328] pci 0000:00:0f.0: reg 1c io port: [0xb000-0xb00f]
[ 0.099335] pci 0000:00:0f.0: reg 20 io port: [0xa800-0xa81f]
[ 0.099341] pci 0000:00:0f.0: reg 24 io port: [0xa400-0xa4ff]
[ 0.099348] pci 0000:00:0f.0: reg 30 32bit mmio:
[0x000000-0x00ffff]
[ 0.099405] pci 0000:00:10.0: reg 20 io port: [0xa000-0xa01f]
[ 0.099427] pci 0000:00:10.0: supports D1 D2
[ 0.099429] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.099505] pci 0000:00:10.0: PME# disabled
[ 0.099620] pci 0000:00:10.1: reg 20 io port: [0x9800-0x981f]
[ 0.099642] pci 0000:00:10.1: supports D1 D2
[ 0.099644] pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.099721] pci 0000:00:10.1: PME# disabled
[ 0.099834] pci 0000:00:10.2: reg 20 io port: [0x9400-0x941f]
[ 0.099856] pci 0000:00:10.2: supports D1 D2
[ 0.099858] pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.099934] pci 0000:00:10.2: PME# disabled
[ 0.100031] pci 0000:00:10.3: reg 10 32bit mmio:
[0xec800000-0xec8000ff]
[ 0.100068] pci 0000:00:10.3: supports D1 D2
[ 0.100071] pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.100146] pci 0000:00:10.3: PME# disabled
[ 0.100271] HPET not enabled in BIOS. You might try hpet=force boot
option
[ 0.100351] pci 0000:00:11.0: quirk: region e400-e47f claimed by
vt8235 PM
[ 0.100428] pci 0000:00:11.0: quirk: region e800-e80f claimed by
vt8235 SMB
[ 0.100557] pci 0000:00:11.1: reg 20 io port: [0x9000-0x900f]
[ 0.100613] pci 0000:00:11.5: reg 10 io port: [0xe000-0xe0ff]
[ 0.100651] pci 0000:00:11.5: supports D1 D2
[ 0.100683] pci 0000:00:12.0: reg 10 io port: [0x8800-0x88ff]
[ 0.100689] pci 0000:00:12.0: reg 14 32bit mmio:
[0xec000000-0xec0000ff]
[ 0.100723] pci 0000:00:12.0: supports D1 D2
[ 0.100725] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.100803] pci 0000:00:12.0: PME# disabled
[ 0.100922] pci 0000:01:00.0: reg 10 32bit mmio:
[0xee000000-0xeeffffff]
[ 0.100928] pci 0000:01:00.0: reg 14 32bit mmio:
[0xf0000000-0xf7ffffff]
[ 0.100934] pci 0000:01:00.0: reg 18 32bit mmio:
[0xef800000-0xef87ffff]
[ 0.100948] pci 0000:01:00.0: reg 30 32bit mmio:
[0xef7e0000-0xef7fffff]
[ 0.100994] pci 0000:00:01.0: bridge 32bit mmio:
[0xee000000-0xef5fffff]
[ 0.100999] pci 0000:00:01.0: bridge 32bit mmio pref:
[0xef700000-0xf7ffffff]
[ 0.101006] pci_bus 0000:00: on NUMA node 0
[ 0.101012] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.101226] ACPI: PCI Interrupt Routing Table
[\_SB_.PCI0.PCI1._PRT]
[ 0.206605] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10
*11 12)
[ 0.207149] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10
11 12)
[ 0.207689] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11
*12)
[ 0.208215] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11
12) *0, disabled.
[ 0.208865] ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 9 10
11 12)
[ 0.209488] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 9 10
11 12)
[ 0.210040] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 *6 7 10 11
12 14 15)
[ 0.210788] SCSI subsystem initialized
[ 0.210900] libata version 3.00 loaded.
[ 0.211050] PCI: Using ACPI for IRQ routing
[ 0.211735] pnp: PnP ACPI init
[ 0.211813] ACPI: bus type pnp registered
[ 0.217363] pnp: PnP ACPI: found 13 devices
[ 0.217436] ACPI: ACPI bus type pnp unregistered
[ 0.217519] system 00:00: iomem range 0x0-0x9ffff could not be
reserved
[ 0.217596] system 00:00: iomem range 0xf0000-0xfffff could not be
reserved
[ 0.217671] system 00:00: iomem range 0x100000-0x3fffffff could not
be reserved
[ 0.217778] system 00:00: iomem range 0xfec00000-0xfec000ff could
not be reserved
[ 0.217885] system 00:00: iomem range 0xfee00000-0xfee00fff has
been reserved
[ 0.217964] system 00:02: ioport range 0xe400-0xe47f has been
reserved
[ 0.218039] system 00:02: ioport range 0xe800-0xe81f could not be
reserved
[ 0.218115] system 00:02: iomem range 0xfff80000-0xffffffff could
not be reserved
[ 0.218223] system 00:02: iomem range 0xffb80000-0xffbfffff has
been reserved
[ 0.218303] system 00:03: ioport range 0x4d0-0x4d1 has been
reserved
[ 0.218384] system 00:0c: ioport range 0x290-0x297 has been
reserved
[ 0.218458] system 00:0c: ioport range 0x370-0x375 has been
reserved
[ 0.253113] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.253188] pci 0000:00:01.0: IO window: disabled
[ 0.253264] pci 0000:00:01.0: MEM window: 0xee000000-0xef5fffff
[ 0.253340] pci 0000:00:01.0: PREFETCH window:
0xef700000-0xf7ffffff
[ 0.253427] pci 0000:00:01.0: setting latency timer to 64
[ 0.253432] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.253435] pci_bus 0000:00: resource 1 mem:
[0x000000-0xffffffffffffffff]
[ 0.253439] pci_bus 0000:01: resource 1 mem:
[0xee000000-0xef5fffff]
[ 0.253442] pci_bus 0000:01: resource 2 pref mem
[0xef700000-0xf7ffffff]
[ 0.253463] NET: Registered protocol family 2
[ 0.253578] IP route cache hash table entries: 32768 (order: 5,
131072 bytes)
[ 0.253954] TCP established hash table entries: 131072 (order: 8,
1048576 bytes)
[ 0.256042] TCP bind hash table entries: 65536 (order: 7, 524288
bytes)
[ 0.257150] TCP: Hash tables configured (established 131072 bind
65536)
[ 0.257225] TCP reno registered
[ 0.257407] NET: Registered protocol family 1
[ 0.257726] Simple Boot Flag at 0x3a set to 0x1
[ 0.258482] microcode: CPU0: AMD CPU family 0x6 not supported
[ 0.258594] Microcode Update Driver: v2.00
<[email protected]>, Peter Oruba
[ 0.263022] Installing knfsd (copyright (C) 1996
[email protected]).
[ 0.263333] msgmni has been set to 1763
[ 0.263582] alg: No test for stdrng (krng)
[ 0.263666] io scheduler noop registered
[ 0.263822] io scheduler cfq registered (default)
[ 0.263907] pci 0000:00:01.0: disabling DAC on VIA PCI bridge
[ 0.264129] pci 0000:01:00.0: Boot video device
[ 0.264161] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.298870] Real Time Clock Driver v1.12b
[ 0.299150] Hangcheck: starting hangcheck timer 0.9.0 (tick is 180
seconds, margin is 60 seconds).
[ 0.299823] Hangcheck: Using get_cycles().
[ 0.300318] processor LNXCPU:00: registered as cooling_device0
[ 0.300499] Serial: 8250/16550 driver, 4 ports, IRQ sharing
disabled
[ 0.300681] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.301549] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.755957] Switched to NOHz mode on CPU #0
[ 3.316010] floppy0: no floppy controllers found
[ 3.317786] brd: module loaded
[ 3.318694] loop: module loaded
[ 3.318938] sata_via 0000:00:0f.0: version 2.4
[ 3.318969] sata_via 0000:00:0f.0: PCI INT A -> GSI 18 (level, low)
-> IRQ 18
[ 3.319104] sata_via 0000:00:0f.0: routed to hard irq line 12
[ 3.319268] scsi0 : sata_via
[ 3.319474] scsi1 : sata_via
[ 3.319621] scsi2 : sata_via
[ 3.319752] ata1: SATA max UDMA/133 port i16@0xd000 bmdma 0xa800
irq 18
[ 3.319828] ata2: SATA max UDMA/133 port i16@0xb800 bmdma 0xa808
irq 18
[ 3.319902] ata3: PATA max UDMA/133 port i16@0xb400 bmdma 0xa810
irq 18
[ 3.320053] pata_via 0000:00:11.1: version 0.3.4
[ 3.320070] pata_via 0000:00:11.1: can't derive routing for PCI INT
A
[ 3.320381] scsi3 : pata_via
[ 3.320525] scsi4 : pata_via
[ 3.321443] ata4: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma
0x9000 irq 14
[ 3.321519] ata5: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma
0x9008 irq 15
[ 3.321673] <6>8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22,
2004)
[ 3.321749] 8139cp 0000:00:0d.0: This (id 10ec:8139 rev 10) is not
an 8139C+ compatible chip, use 8139too
[ 3.321868] 8139cp 0000:00:0e.0: This (id 10ec:8139 rev 10) is not
an 8139C+ compatible chip, use 8139too
[ 3.322128] 8139too Fast Ethernet driver 0.9.28
[ 3.322217] 8139too 0000:00:0d.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[ 3.322672] eth0: RealTek RTL8139 at 0xf873a000, 00:e0:4c:02:25:33,
IRQ 16
[ 3.322765] 8139too 0000:00:0e.0: PCI INT A -> GSI 17 (level, low)
-> IRQ 17
[ 3.323163] eth1: RealTek RTL8139 at 0xf873e000, 00:50:bf:e0:d3:62,
IRQ 17
[ 3.323424] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 3.323499] PNP: PS/2 appears to have AUX port disabled, if this is
incorrect please boot with i8042.nopnp
[ 3.323973] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.324387] mice: PS/2 mouse device common for all mice
[ 3.324587] cpuidle: using governor ladder
[ 3.324659] cpuidle: using governor menu
[ 3.324936] TCP cubic registered
[ 3.325008] NET: Registered protocol family 17
[ 3.325211] RPC: Registered udp transport module.
[ 3.325284] RPC: Registered tcp transport module.
[ 3.325359] Using IPI Shortcut mode
[ 3.346864] input: AT Translated Set 2 keyboard as
/class/input/input0
[ 3.493910] ata4.00: ATA-7: Maxtor 6L160P0, BAH41G10, max UDMA/133
[ 3.493987] ata4.00: 312581808 sectors, multi 16: LBA48
[ 3.494293] ata4.01: ATA-7: Hitachi HDS721616PLAT80, P22OA85A, max
UDMA/133
[ 3.494369] ata4.01: 321672960 sectors, multi 16: LBA48
[ 3.509756] ata4.00: configured for UDMA/133
[ 3.524390] ata4.01: configured for UDMA/133
[ 3.650459] ata1: SATA link down (SStatus 0 SControl 310)
[ 3.968033] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3.992344] ata2.00: ATA-8: Hitachi HDT721010SLA360, ST6OA3AA, max
UDMA/133
[ 3.992419] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth
0/32)
[ 4.008361] ata2.00: configured for UDMA/133
[ 4.008583] scsi 1:0:0:0: Direct-Access ATA Hitachi
HDT72101 ST6O PQ: 0 ANSI: 5
[ 4.008880] sd 1:0:0:0: [sda] 1953525168 512-byte logical blocks:
(1.00 TB/931 GiB)
[ 4.009035] sd 1:0:0:0: [sda] Write Protect is off
[ 4.009111] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.009135] sd 1:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 4.009375] sda:
[ 4.009642] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 4.022505] sda1 sda2
[ 4.022933] sd 1:0:0:0: [sda] Attached SCSI disk
[ 4.175093] scsi 3:0:0:0: Direct-Access ATA Maxtor 6L160P0
BAH4 PQ: 0 ANSI: 5
[ 4.175361] sd 3:0:0:0: [sdb] 312581808 512-byte logical blocks:
(160 GB/149 GiB)
[ 4.175509] sd 3:0:0:0: [sdb] Write Protect is off
[ 4.175582] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 4.175604] sd 3:0:0:0: [sdb] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 4.175826] sdb:
[ 4.176044] sd 3:0:0:0: Attached scsi generic sg1 type 0
[ 4.209190] sdb1
[ 4.209360] scsi 3:0:1:0: Direct-Access ATA Hitachi
HDS72161 P22O PQ: 0 ANSI: 5
[ 4.209710] sd 3:0:1:0: [sdc] 321672960 512-byte logical blocks:
(164 GB/153 GiB)
[ 4.209861] sd 3:0:1:0: [sdc] Write Protect is off
[ 4.209933] sd 3:0:1:0: [sdc] Mode Sense: 00 3a 00 00
[ 4.209955] sd 3:0:1:0: [sdc] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 4.210165] sdc:
[ 4.210390] sd 3:0:1:0: Attached scsi generic sg2 type 0
[ 4.220707] sdc1 sdc2
[ 4.220963] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 4.221257] sd 3:0:1:0: [sdc] Attached SCSI disk
[ 4.375829] REISERFS (device sdc1): found reiserfs format "3.6"
with standard journal
[ 4.375953] REISERFS (device sdc1): using ordered data mode
[ 4.386195] REISERFS (device sdc1): journal params: device sdc1,
size 8192, journal first block 18, max trans len 1024, max batch 900,
max commit age 30, max trans age 30
[ 4.387850] REISERFS (device sdc1): checking transaction log (sdc1)
[ 4.848572] REISERFS (device sdc1): replayed 15 transactions in 0
seconds
[ 4.869310] REISERFS (device sdc1): Using r5 hash to sort names
[ 4.869424] VFS: Mounted root (reiserfs filesystem) readonly on
device 8:33.
[ 4.869536] Freeing unused kernel memory: 384k freed
[ 7.448690] udev: starting version 141
[ 7.448729] udev: deprecated sysfs layout; update the kernel or
disable CONFIG_SYSFS_DEPRECATED; some udev features will not work
correctly
[ 7.956400] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1380500
action 0x6
[ 7.956405] ata2.00: BMDMA stat 0x4
[ 7.956410] ata2: SError: { UnrecovData Proto 10B8B Dispar BadCRC
TrStaTrns }
[ 7.956420] ata2.00: cmd c8/00:20:00:08:00/00:00:00:00:00/e0 tag 0
dma 16384 in
[ 7.956422] res 51/84:00:1f:08:00/00:00:00:00:00/e0 Emask
0x12 (ATA bus error)
[ 7.956426] ata2.00: status: { DRDY ERR }
[ 7.956428] ata2.00: error: { ICRC ABRT }
[ 7.956439] ata2: hard resetting link
[ 8.276541] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 8.300891] ata2.00: configured for UDMA/133
[ 8.300956] ata2: EH complete
[ 8.306329] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1380500
action 0x6
[ 8.306334] ata2.00: BMDMA stat 0x5
[ 8.306339] ata2: SError: { UnrecovData Proto 10B8B Dispar BadCRC
TrStaTrns }
[ 8.306349] ata2.00: cmd c8/00:20:00:08:00/00:00:00:00:00/e0 tag 0
dma 16384 in
[ 8.306351] res 51/84:00:1f:08:00/00:00:00:00:00/e0 Emask
0x12 (ATA bus error)
[ 8.306354] ata2.00: status: { DRDY ERR }
[ 8.306357] ata2.00: error: { ICRC ABRT }
[ 8.306368] ata2: hard resetting link
[ 8.624043] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 8.648362] ata2.00: configured for UDMA/133
[ 8.648385] ata2: EH complete
[ 8.656260] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1380500
action 0x6
[ 8.656264] ata2.00: BMDMA stat 0x5
[ 8.656269] ata2: SError: { UnrecovData Proto 10B8B Dispar BadCRC
TrStaTrns }
[ 8.656278] ata2.00: cmd c8/00:20:00:08:00/00:00:00:00:00/e0 tag 0
dma 16384 in
[ 8.656280] res 51/84:00:1f:08:00/00:00:00:00:00/e0 Emask
0x12 (ATA bus error)
[ 8.656284] ata2.00: status: { DRDY ERR }
[ 8.656286] ata2.00: error: { ICRC ABRT }
[ 8.656296] ata2: hard resetting link
[ 8.976032] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9.000360] ata2.00: configured for UDMA/133
[ 9.000367] ata2: EH complete
[ 9.006004] ata2.00: limiting speed to UDMA/100:PIO4
[ 9.006008] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1380500
action 0x6
[ 9.006011] ata2.00: BMDMA stat 0x4
[ 9.006014] ata2: SError: { UnrecovData Proto 10B8B Dispar BadCRC
TrStaTrns }
[ 9.006021] ata2.00: cmd c8/00:20:00:08:00/00:00:00:00:00/e0 tag 0
dma 16384 in
[ 9.006023] res 51/84:00:1f:08:00/00:00:00:00:00/e0 Emask
0x12 (ATA bus error)
[ 9.006026] ata2.00: status: { DRDY ERR }
[ 9.006028] ata2.00: error: { ICRC ABRT }
[ 9.006035] ata2: hard resetting link
[ 9.324032] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9.348898] ata2.00: configured for UDMA/100
[ 9.348904] ata2: EH complete
[ 9.355898] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1280500
action 0x6
[ 9.355901] ata2.00: BMDMA stat 0x4
[ 9.355904] ata2: SError: { UnrecovData Proto 10B8B BadCRC
TrStaTrns }
[ 9.355912] ata2.00: cmd c8/00:20:00:08:00/00:00:00:00:00/e0 tag 0
dma 16384 in
[ 9.355913] res 51/84:00:1f:08:00/00:00:00:00:00/e0 Emask
0x12 (ATA bus error)
[ 9.355917] ata2.00: status: { DRDY ERR }
[ 9.355919] ata2.00: error: { ICRC ABRT }
[ 9.355926] ata2: hard resetting link
[ 9.672032] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9.696360] ata2.00: configured for UDMA/100
[ 9.696366] ata2: EH complete
[ 9.705768] ata2.00: limiting speed to UDMA/33:PIO4
[ 9.705772] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1380500
action 0x6
[ 9.705775] ata2.00: BMDMA stat 0x5
[ 9.705778] ata2: SError: { UnrecovData Proto 10B8B Dispar BadCRC
TrStaTrns }
[ 9.705785] ata2.00: cmd c8/00:20:00:08:00/00:00:00:00:00/e0 tag 0
dma 16384 in
[ 9.705787] res 51/84:00:1f:08:00/00:00:00:00:00/e0 Emask
0x12 (ATA bus error)
[ 9.705790] ata2.00: status: { DRDY ERR }
[ 9.705793] ata2.00: error: { ICRC ABRT }
[ 9.705800] ata2: hard resetting link
[ 10.024610] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 10.048360] ata2.00: configured for UDMA/33
[ 10.048375] sd 1:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
[ 10.048379] sd 1:0:0:0: [sda] Sense Key : 0xb [current]
[descriptor]
[ 10.048384] Descriptor sense data with sense descriptors (in hex):
[ 10.048387] 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 10.048395] 00 00 08 1f
[ 10.048398] sd 1:0:0:0: [sda] ASC=0x47 ASCQ=0x0
[ 10.048402] end_request: I/O error, dev sda, sector 2048
[ 10.048408] Buffer I/O error on device sda1, logical block 0
[ 10.048414] Buffer I/O error on device sda1, logical block 1
[ 10.048418] Buffer I/O error on device sda1, logical block 2
[ 10.048421] Buffer I/O error on device sda1, logical block 3
[ 10.048436] ata2: EH complete
[ 10.060522] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1380500
action 0x6
[ 10.060526] ata2.00: BMDMA stat 0x5
[ 10.060530] ata2: SError: { UnrecovData Proto 10B8B Dispar BadCRC
TrStaTrns }
[ 10.060538] ata2.00: cmd c8/00:20:00:88:38/00:00:00:00:00/e1 tag 0
dma 16384 in
[ 10.060540] res 51/84:00:1f:88:38/00:00:00:00:00/e1 Emask
0x12 (ATA bus error)
[ 10.060543] ata2.00: status: { DRDY ERR }
[ 10.060545] ata2.00: error: { ICRC ABRT }
[ 10.060554] ata2: hard resetting link
[ 10.376035] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 10.400361] ata2.00: configured for UDMA/33
[ 10.400372] ata2: EH complete
[ 10.410412] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1380500
action 0x6
[ 10.410415] ata2.00: BMDMA stat 0x5
[ 10.410418] ata2: SError: { UnrecovData Proto 10B8B Dispar BadCRC
TrStaTrns }
[ 10.410426] ata2.00: cmd c8/00:20:00:88:38/00:00:00:00:00/e1 tag 0
dma 16384 in
[ 10.410427] res 51/84:00:1f:88:38/00:00:00:00:00/e1 Emask
0x12 (ATA bus error)
[ 10.410431] ata2.00: status: { DRDY ERR }
[ 10.410433] ata2.00: error: { ICRC ABRT }
[ 10.410440] ata2: hard resetting link
[ 10.728032] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 10.752987] ata2.00: configured for UDMA/33
[ 10.752993] ata2: EH complete
[ 10.760309] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1380500
action 0x6
[ 10.760313] ata2.00: BMDMA stat 0x4
[ 10.760316] ata2: SError: { UnrecovData Proto 10B8B Dispar BadCRC
TrStaTrns }
[ 10.760323] ata2.00: cmd c8/00:20:00:88:38/00:00:00:00:00/e1 tag 0
dma 16384 in
[ 10.760325] res 51/84:00:1f:88:38/00:00:00:00:00/e1 Emask
0x12 (ATA bus error)
[ 10.760328] ata2.00: status: { DRDY ERR }
[ 10.760330] ata2.00: error: { ICRC ABRT }
[ 10.760338] ata2: hard resetting link
[ 11.080032] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 11.104359] ata2.00: configured for UDMA/33
[ 11.104365] ata2: EH complete
[ 11.110213] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1380500
action 0x6
[ 11.110217] ata2.00: BMDMA stat 0x5
[ 11.110220] ata2: SError: { UnrecovData Proto 10B8B Dispar BadCRC
TrStaTrns }
[ 11.110227] ata2.00: cmd c8/00:20:00:88:38/00:00:00:00:00/e1 tag 0
dma 16384 in
[ 11.110229] res 51/84:00:1f:88:38/00:00:00:00:00/e1 Emask
0x12 (ATA bus error)
[ 11.110232] ata2.00: status: { DRDY ERR }
[ 11.110235] ata2.00: error: { ICRC ABRT }
[ 11.110242] ata2: hard resetting link
[ 11.428698] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 11.452365] ata2.00: configured for UDMA/33
[ 11.452371] ata2: EH complete
[ 36.534034] REISERFS (device sdb1): found reiserfs format "3.6"
with standard journal
[ 36.534061] REISERFS (device sdb1): using ordered data mode
[ 36.548375] REISERFS (device sdb1): journal params: device sdb1,
size 8192, journal first block 18, max trans len 1024, max batch 900,
max commit age 30, max trans age 30
[ 36.549794] REISERFS (device sdb1): checking transaction log (sdb1)
[ 36.566360] REISERFS (device sdb1): Using r5 hash to sort names
[ 36.759675] Adding 674720k swap on /dev/sdc2. Priority:-1
extents:1 across:674720k
[ 41.087727] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 41.194335] nf_conntrack version 0.5.0 (14321 buckets, 57284 max)
[ 41.194606] CONFIG_NF_CT_ACCT is deprecated and will be removed
soon. Please use
[ 41.194609] nf_conntrack.acct=1 kernel parameter, acct=1
nf_conntrack module option or
[ 41.194612] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 41.818616] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x180000
action 0x6 frozen
[ 41.818624] ata2: SError: { 10B8B Dispar }
[ 41.818633] ata2.00: cmd c8/00:20:00:88:38/00:00:00:00:00/e1 tag 0
dma 16384 in
[ 41.818635] res 40/00:00:1f:88:38/00:00:00:00:00/e1 Emask
0x4 (timeout)
[ 41.818639] ata2.00: status: { DRDY }
[ 41.818650] ata2: hard resetting link
[ 42.138653] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 42.163006] ata2.00: configured for UDMA/33
[ 42.163033] ata2: EH complete
[ 42.167969] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1380500
action 0x6
[ 42.167975] ata2.00: BMDMA stat 0x5
[ 42.167980] ata2: SError: { UnrecovData Proto 10B8B Dispar BadCRC
TrStaTrns }
[ 42.167990] ata2.00: cmd c8/00:20:00:88:38/00:00:00:00:00/e1 tag 0
dma 16384 in
[ 42.167991] res 51/84:00:1f:88:38/00:00:00:00:00/e1 Emask
0x12 (ATA bus error)
[ 42.167995] ata2.00: status: { DRDY ERR }
[ 42.167998] ata2.00: error: { ICRC ABRT }
[ 42.168009] ata2: hard resetting link
[ 42.486693] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 42.511044] ata2.00: configured for UDMA/33
[ 42.511072] sd 1:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
[ 42.511076] sd 1:0:0:0: [sda] Sense Key : 0xb [current]
[descriptor]
[ 42.511082] Descriptor sense data with sense descriptors (in hex):
[ 42.511084] 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 42.511092] 01 38 88 1f
[ 42.511096] sd 1:0:0:0: [sda] ASC=0x47 ASCQ=0x0
[ 42.511100] end_request: I/O error, dev sda, sector 20482048
[ 42.511106] Buffer I/O error on device sda2, logical block 0
[ 42.511112] Buffer I/O error on device sda2, logical block 1
[ 42.511116] Buffer I/O error on device sda2, logical block 2
[ 42.511119] Buffer I/O error on device sda2, logical block 3
[ 42.511142] ata2: EH complete
[ 43.898662] eth0: link down
[ 47.533238] eth1: link down
[ 100.814847] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1300500
action 0x6
[ 100.814852] ata2.00: BMDMA stat 0x5
[ 100.814857] ata2: SError: { UnrecovData Proto Dispar BadCRC
TrStaTrns }
[ 100.814867] ata2.00: cmd 25/00:00:00:00:00/00:02:00:00:00/e0 tag 0
dma 262144 in
[ 100.814869] res 51/84:80:80:01:00/84:00:00:00:00/e0 Emask
0x12 (ATA bus error)
[ 100.814872] ata2.00: status: { DRDY ERR }
[ 100.814875] ata2.00: error: { ICRC ABRT }
[ 100.814886] ata2: hard resetting link
[ 101.132036] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 101.156362] ata2.00: configured for UDMA/33
[ 101.156375] ata2: EH complete
[ 101.173825] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1300500
action 0x6
[ 101.173831] ata2.00: BMDMA stat 0x5
[ 101.173836] ata2: SError: { UnrecovData Proto Dispar BadCRC
TrStaTrns }
[ 101.173845] ata2.00: cmd 25/00:00:00:06:00/00:02:00:00:00/e0 tag 0
dma 262144 in
[ 101.173847] res 51/84:90:70:07:00/84:00:00:00:00/e0 Emask
0x12 (ATA bus error)
[ 101.173851] ata2.00: status: { DRDY ERR }
[ 101.173853] ata2.00: error: { ICRC ABRT }
[ 101.173864] ata2: hard resetting link
[ 101.492043] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 101.516362] ata2.00: configured for UDMA/33
[ 101.516380] ata2: EH complete
[ 101.529902] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1380500
action 0x6
[ 101.529908] ata2.00: BMDMA stat 0x5
[ 101.529913] ata2: SError: { UnrecovData Proto 10B8B Dispar BadCRC
TrStaTrns }
[ 101.529923] ata2.00: cmd 25/00:00:00:08:00/00:02:00:00:00/e0 tag 0
dma 262144 in
[ 101.529925] res 51/84:e0:20:08:00/84:01:00:00:00/e0 Emask
0x12 (ATA bus error)
[ 101.529928] ata2.00: status: { DRDY ERR }
[ 101.529931] ata2.00: error: { ICRC ABRT }
[ 101.529942] ata2: hard resetting link
[ 101.848036] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 101.857593] ata2.00: failed to read native max address
(err_mask=0x1)
[ 101.857597] ata2.00: HPA support seems broken, skipping HPA
handling
[ 101.936194] ata2.00: configured for UDMA/33
[ 101.936206] ata2: EH complete
[ 101.953932] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1380500
action 0x6
[ 101.953935] ata2.00: BMDMA stat 0x5
[ 101.953938] ata2: SError: { UnrecovData Proto 10B8B Dispar BadCRC
TrStaTrns }
[ 101.953946] ata2.00: cmd 25/00:00:00:08:00/00:02:00:00:00/e0 tag 0
dma 262144 in
[ 101.953947] res 51/84:e0:20:08:00/84:01:00:00:00/e0 Emask
0x12 (ATA bus error)
[ 101.953951] ata2.00: status: { DRDY ERR }
[ 101.953953] ata2.00: error: { ICRC ABRT }
[ 101.953960] ata2: hard resetting link
[ 102.272033] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 102.296192] ata2.00: configured for UDMA/33
[ 102.296199] ata2: EH complete
[ 102.303830] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1280500
action 0x6
[ 102.303834] ata2.00: BMDMA stat 0x5
[ 102.303837] ata2: SError: { UnrecovData Proto 10B8B BadCRC
TrStaTrns }
[ 102.303845] ata2.00: cmd 25/00:00:00:08:00/00:02:00:00:00/e0 tag 0
dma 262144 in
[ 102.303846] res 51/84:e0:20:08:00/84:01:00:00:00/e0 Emask
0x12 (ATA bus error)
[ 102.303850] ata2.00: status: { DRDY ERR }
[ 102.303852] ata2.00: error: { ICRC ABRT }
[ 102.303859] ata2: hard resetting link
[ 102.622398] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 102.644192] ata2.00: configured for UDMA/33
[ 102.644198] ata2: EH complete
[ 102.653732] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1380500 action 0x6
[ 102.653736] ata2.00: BMDMA stat 0x5
[ 102.653739] ata2: SError: { UnrecovData Proto 10B8B Dispar BadCRC TrStaTrns }
[ 102.653747] ata2.00: cmd 25/00:00:00:08:00/00:02:00:00:00/e0 tag 0
dma 262144 in
[ 102.653748] res 51/84:e0:20:08:00/84:01:00:00:00/e0 Emask
0x12 (ATA bus error)
[ 102.653752] ata2.00: status: { DRDY ERR }
[ 102.653754] ata2.00: error: { ICRC ABRT }
[ 102.653761] ata2: hard resetting link
[ 102.972033] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 102.996192] ata2.00: configured for UDMA/33
[ 102.996198] ata2: EH complete
[ 103.003636] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1380500 action 0x6
[ 103.003639] ata2.00: BMDMA stat 0x5
[ 103.003642] ata2: SError: { UnrecovData Proto 10B8B Dispar BadCRC TrStaTrns }
[ 103.003650] ata2.00: cmd 25/00:00:00:08:00/00:02:00:00:00/e0 tag 0
dma 262144 in
[ 103.003651] res 51/84:e0:20:08:00/84:01:00:00:00/e0 Emask
0x12 (ATA bus error)
[ 103.003655] ata2.00: status: { DRDY ERR }
[ 103.003657] ata2.00: error: { ICRC ABRT }
[ 103.003664] ata2: hard resetting link
[ 103.320043] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 103.344194] ata2.00: configured for UDMA/33
[ 103.344216] ata2: EH complete
[ 103.353544] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1380500 action 0x6
[ 103.353548] ata2.00: BMDMA stat 0x5
[ 103.353552] ata2: SError: { UnrecovData Proto 10B8B Dispar BadCRC TrStaTrns }
[ 103.353561] ata2.00: cmd 25/00:00:00:08:00/00:02:00:00:00/e0 tag 0
dma 262144 in
[ 103.353563] res 51/84:e0:20:08:00/84:01:00:00:00/e0 Emask
0x12 (ATA bus error)
[ 103.353567] ata2.00: status: { DRDY ERR }
[ 103.353569] ata2.00: error: { ICRC ABRT }
[ 103.353579] ata2: hard resetting link
[ 103.672032] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 103.696192] ata2.00: configured for UDMA/33
[ 103.696220] sd 1:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
[ 103.696224] sd 1:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 103.696230] Descriptor sense data with sense descriptors (in hex):
[ 103.696233] 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 103.696240] 00 00 08 20
[ 103.696244] sd 1:0:0:0: [sda] ASC=0x47 ASCQ=0x0
[ 103.696248] end_request: I/O error, dev sda, sector 2048
[ 103.696254] Buffer I/O error on device sda, logical block 256
[ 103.696260] Buffer I/O error on device sda, logical block 257
[ 103.696263] Buffer I/O error on device sda, logical block 258
[ 103.696267] Buffer I/O error on device sda, logical block 259
[ 103.696270] Buffer I/O error on device sda, logical block 260
[ 103.696273] Buffer I/O error on device sda, logical block 261
[ 103.696276] Buffer I/O error on device sda, logical block 262
[ 103.696279] Buffer I/O error on device sda, logical block 263
[ 103.696282] Buffer I/O error on device sda, logical block 264
[ 103.696285] Buffer I/O error on device sda, logical block 265
[ 103.696322] ata2: EH complete
--
Corentin Chary
http://xf.iksaif.net
On Sun, 11 Oct 2009 11:54:49 +0200
Corentin Chary <[email protected]> wrote:
> Hi,
> I recently needed some more space and bought a Deskstar 7K1000.B for my server.
> The motherboard is old, and did not have SATA port, so I added a
> VT6421 PCI SATA controller.
Lots of 6421 setups do not work on Linux full stop. I've asked VIA
several times for the relevant data sheet/info to fix this and they've
never done more than acknowledge receipt of the mail.
Alan
On Sun, Oct 11, 2009 at 3:16 PM, Alan Cox <[email protected]> wrote:
> On Sun, 11 Oct 2009 11:54:49 +0200
> Corentin Chary <[email protected]> wrote:
>
>> Hi,
>> I recently needed some more space and bought a Deskstar 7K1000.B for my server.
>> The motherboard is old, and did not have SATA port, so I added a
>> VT6421 PCI SATA controller.
>
> Lots of 6421 setups do not work on Linux full stop. I've asked VIA
> several times for the relevant data sheet/info to fix this and they've
> never done more than acknowledge receipt of the mail.
>
> Alan
>
Great :(
I think I'll try to find another controller card/motherboard...
--
Corentin Chary
http://xf.iksaif.net
On Sun, Oct 11, 2009 at 3:16 PM, Alan Cox <[email protected]> wrote:
> On Sun, 11 Oct 2009 11:54:49 +0200
> Corentin Chary <[email protected]> wrote:
>
>> Hi,
>> I recently needed some more space and bought a Deskstar 7K1000.B for my server.
>> The motherboard is old, and did not have SATA port, so I added a
>> VT6421 PCI SATA controller.
>
> Lots of 6421 setups do not work on Linux full stop. I've asked VIA
> several times for the relevant data sheet/info to fix this and they've
> never done more than acknowledge receipt of the mail.
>
> Alan
>
I tried to contact VIA, they said the datasheet have been available
for some month,
here is the link they gave to me:
ftp://vtbridge.org/Docs/Storage/DS_VT6421A_100_CCPL.PDF
Thanks,
--
Corentin Chary
http://xf.iksaif.net
Hi Alan,
Alan Cox wrote:
>> I recently needed some more space and bought a Deskstar 7K1000.B for my server.
>> The motherboard is old, and did not have SATA port, so I added a
>> VT6421 PCI SATA controller.
>
> Lots of 6421 setups do not work on Linux full stop. I've asked VIA
> several times for the relevant data sheet/info to fix this and they've
> never done more than acknowledge receipt of the mail.
Whom did you e-mail?
The document is available from
ftp://ftp.vtbridge.org/Docs/Storage/DS_VT6421A_100_CCPL.PDF
for almost one year now.
If you requested it, maybe it was put there but somebody just forgot to
send follow-up mail to you.
To anyone working on Linux or other Free Software regarding VIA
hardware: If you need documentation, or if you have any other issues,
please contact me. I am the Liaison and I can talk with various people
and departments inside VIA.
There are some things where VIA has no documentation, and there are
other parts like video acceleration where documentation cannot be
published due to 3rd party patents and patent licensing schemes.
But for general hardware like storage controller, north/southbridge,
audio codecs, ... the documentation is possible to be released without NDA.
--
Harald Welte <[email protected]>