Just installed 3.8.1....
Thought this had been fixed? Note it causes the kernel to
show up as tainted after the 1st...
As the system was coming up and initializing the bond0 driver:
[ 19.847743] ixgbe 0000:06:00.0: registered PHC device on eth_s2_0
[ 20.258245] BUG: scheduling while atomic: ifup-bonding/2003/0x00000002
[ 20.264812] 4 locks held by ifup-bonding/2003:
[ 20.269298] #0: (&buffer->mutex){......}, at: [<ffffffff811c401f>]
sysfs_write_file+0x3f/0x150
[ 20.278319] #1: (s_active#59){......}, at: [<ffffffff811c409b>]
sysfs_write_file+0xbb/0x150
[ 20.287088] #2: (rtnl_mutex){......}, at: [<ffffffff81590bf0>]
rtnl_trylock+0x10/0x20
[ 20.295373] #3: (&bond->lock){......}, at: [<ffffffff8145be6f>]
bond_enslave+0x4ef/0xb80
[ 20.303912] Modules linked in: iptable_filter kvm_intel kvm acpi_cpufreq
mperf button processor mousedev iTCO_wdt
[ 20.314695] Pid: 2003, comm: ifup-bonding Not tainted 3.8.1-Isht-Van #5
[ 20.321340] Call Trace:
[ 20.323833] [<ffffffff8162b029>] __schedule_bug+0x5e/0x6c
[ 20.329356] [<ffffffff81634592>] __schedule+0x762/0x7f0
[ 20.334701] [<ffffffff81634734>] schedule+0x24/0x70
[ 20.339703] [<ffffffff816336f4>] schedule_hrtimeout_range_clock+0xa4/0x130
[ 20.346699] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
[ 20.352130] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
[ 20.358434] [<ffffffff8163378e>] schedule_hrtimeout_range+0xe/0x10
[ 20.364734] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
[ 20.370082] [<ffffffff814b2d7c>] ixgbe_acquire_swfw_sync_X540+0xbc/0x100
[ 20.376905] [<ffffffff814aeb0d>] ixgbe_read_phy_reg_generic+0x3d/0x140
[ 20.383553] [<ffffffff814aedac>]
ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
[ 20.391499] [<ffffffff8145be6f>] ? bond_enslave+0x4ef/0xb80
[ 20.397194] [<ffffffff814a64e4>] ixgbe_get_settings+0x34/0x340
[ 20.403148] [<ffffffff81586ab8>] __ethtool_get_settings+0x88/0x130
[ 20.409448] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
[ 20.415833] [<ffffffff8145bed9>] bond_enslave+0x559/0xb80
[ 20.421356] [<ffffffff8146454f>] bonding_store_slaves+0x16f/0x1c0
[ 20.427569] [<ffffffff813bfb83>] dev_attr_store+0x13/0x30
[ 20.433091] [<ffffffff811c40b4>] sysfs_write_file+0xd4/0x150
[ 20.438872] [<ffffffff81154b81>] vfs_write+0xb1/0x190
[ 20.444047] [<ffffffff81154ee0>] sys_write+0x50/0xa0
[ 20.449137] [<ffffffff81637092>] system_call_fastpath+0x16/0x1b
[ 20.455264] BUG: scheduling while atomic: ifup-bonding/2003/0x00000002
[ 20.461851] 4 locks held by ifup-bonding/2003:
[ 20.466334] #0: (&buffer->mutex){......}, at: [<ffffffff811c401f>]
sysfs_write_file+0x3f/0x150
[ 20.475356] #1: (s_active#59){......}, at: [<ffffffff811c409b>]
sysfs_write_file+0xbb/0x150
[ 20.484117] #2: (rtnl_mutex){......}, at: [<ffffffff81590bf0>]
rtnl_trylock+0x10/0x20
[ 20.492403] #3: (&bond->lock){......}, at: [<ffffffff8145be6f>]
bond_enslave+0x4ef/0xb80
[ 20.500902] Modules linked in: iptable_filter kvm_intel kvm acpi_cpufreq
mperf button processor mousedev iTCO_wdt
[ 20.511640] Pid: 2003, comm: ifup-bonding Tainted: G W
3.8.1-Isht-Van #5
[ 20.519240] Call Trace:
[ 20.521729] [<ffffffff8162b029>] __schedule_bug+0x5e/0x6c
[ 20.527251] [<ffffffff81634592>] __schedule+0x762/0x7f0
[ 20.532599] [<ffffffff81634734>] schedule+0x24/0x70
[ 20.537599] [<ffffffff816336f4>] schedule_hrtimeout_range_clock+0xa4/0x130
[ 20.544592] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
[ 20.550026] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
[ 20.555462] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
[ 20.561763] [<ffffffff8163378e>] schedule_hrtimeout_range+0xe/0x10
[ 20.568064] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
[ 20.573415] [<ffffffff814b2cae>] ixgbe_release_swfw_sync_X540+0x4e/0x60
[ 20.580146] [<ffffffff814aebdd>] ixgbe_read_phy_reg_generic+0x10d/0x140
[ 20.586960] [<ffffffff814aedac>]
ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
[ 20.594908] [<ffffffff8145be6f>] ? bond_enslave+0x4ef/0xb80
[ 20.600601] [<ffffffff814a64e4>] ixgbe_get_settings+0x34/0x340
[ 20.606557] [<ffffffff81586ab8>] __ethtool_get_settings+0x88/0x130
[ 20.612858] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
[ 20.619244] [<ffffffff8145bed9>] bond_enslave+0x559/0xb80
[ 20.624767] [<ffffffff8146454f>] bonding_store_slaves+0x16f/0x1c0
[ 20.630983] [<ffffffff813bfb83>] dev_attr_store+0x13/0x30
[ 20.636503] [<ffffffff811c40b4>] sysfs_write_file+0xd4/0x150
[ 20.642283] [<ffffffff81154b81>] vfs_write+0xb1/0x190
[ 20.647462] [<ffffffff81154ee0>] sys_write+0x50/0xa0
[ 20.652548] [<ffffffff81637092>] system_call_fastpath+0x16/0x1b
[ 20.658696] bonding: bond0: enslaving eth_s2_0 as an active interface with a
down link.
[ 20.676577] bonding: bond0: Adding slave eth_s2_1.
[ 20.743760] pps pps1: new PPS source ptp1
[ 20.747792] ixgbe 0000:06:00.1: registered PHC device on eth_s2_1
[ 21.150267] BUG: scheduling while atomic: ifup-bonding/2003/0x00000002
[ 21.156836] 4 locks held by ifup-bonding/2003:
[ 21.161319] #0: (&buffer->mutex){......}, at: [<ffffffff811c401f>]
sysfs_write_file+0x3f/0x150
[ 21.170388] #1: (s_active#59){......}, at: [<ffffffff811c409b>]
sysfs_write_file+0xbb/0x150
[ 21.179149] #2: (rtnl_mutex){......}, at: [<ffffffff81590bf0>]
rtnl_trylock+0x10/0x20
[ 21.187403] #3: (&bond->lock){......}, at: [<ffffffff8145be6f>]
bond_enslave+0x4ef/0xb80
[ 21.195904] Modules linked in: iptable_filter kvm_intel kvm acpi_cpufreq
mperf button processor mousedev iTCO_wdt
[ 21.206644] Pid: 2003, comm: ifup-bonding Tainted: G W
3.8.1-Isht-Van #5
[ 21.214240] Call Trace:
[ 21.216732] [<ffffffff8162b029>] __schedule_bug+0x5e/0x6c
[ 21.222254] [<ffffffff81634592>] __schedule+0x762/0x7f0
[ 21.227604] [<ffffffff81634734>] schedule+0x24/0x70
[ 21.232606] [<ffffffff816336f4>] schedule_hrtimeout_range_clock+0xa4/0x130
[ 21.239601] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
[ 21.245033] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
[ 21.251339] [<ffffffff8163378e>] schedule_hrtimeout_range+0xe/0x10
[ 21.257635] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
[ 21.262987] [<ffffffff814b2d7c>] ixgbe_acquire_swfw_sync_X540+0xbc/0x100
[ 21.269811] [<ffffffff814aeb0d>] ixgbe_read_phy_reg_generic+0x3d/0x140
[ 21.276461] [<ffffffff814aedac>]
ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
[ 21.284409] [<ffffffff8145be6f>] ? bond_enslave+0x4ef/0xb80
[ 21.290106] [<ffffffff814a64e4>] ixgbe_get_settings+0x34/0x340
[ 21.296067] [<ffffffff81586ab8>] __ethtool_get_settings+0x88/0x130
[ 21.302369] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
[ 21.308754] [<ffffffff8145bed9>] bond_enslave+0x559/0xb80
[ 21.314278] [<ffffffff8146454f>] bonding_store_slaves+0x16f/0x1c0
[ 21.320491] [<ffffffff813bfb83>] dev_attr_store+0x13/0x30
[ 21.326009] [<ffffffff811c40b4>] sysfs_write_file+0xd4/0x150
[ 21.331793] [<ffffffff81154b81>] vfs_write+0xb1/0x190
[ 21.336964] [<ffffffff81154ee0>] sys_write+0x50/0xa0
[ 21.342053] [<ffffffff81637092>] system_call_fastpath+0x16/0x1b
[ 21.348191] BUG: scheduling while atomic: ifup-bonding/2003/0x00000002
[ 21.354775] 4 locks held by ifup-bonding/2003:
[ 21.359258] #0: (&buffer->mutex){......}, at: [<ffffffff811c401f>]
sysfs_write_file+0x3f/0x150
[ 21.368283] #1: (s_active#59){......}, at: [<ffffffff811c409b>]
sysfs_write_file+0xbb/0x150
[ 21.377104] #2: (rtnl_mutex){......}, at: [<ffffffff81590bf0>]
rtnl_trylock+0x10/0x20
[ 21.385343] #3: (&bond->lock){......}, at: [<ffffffff8145be6f>]
bond_enslave+0x4ef/0xb80
[ 21.393887] Modules linked in: iptable_filter kvm_intel kvm acpi_cpufreq
mperf button processor mousedev iTCO_wdt
[ 21.404575] Pid: 2003, comm: ifup-bonding Tainted: G W
3.8.1-Isht-Van #5
[ 21.412176] Call Trace:
[ 21.414666] [<ffffffff8162b029>] __schedule_bug+0x5e/0x6c
[ 21.420188] [<ffffffff81634592>] __schedule+0x762/0x7f0
[ 21.425536] [<ffffffff81634734>] schedule+0x24/0x70
[ 21.430541] [<ffffffff816336f4>] schedule_hrtimeout_range_clock+0xa4/0x130
[ 21.437532] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
[ 21.442967] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
[ 21.448407] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
[ 21.454712] [<ffffffff8163378e>] schedule_hrtimeout_range+0xe/0x10
[ 21.461015] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
[ 21.466370] [<ffffffff814b2cae>] ixgbe_release_swfw_sync_X540+0x4e/0x60
[ 21.473105] [<ffffffff814aebdd>] ixgbe_read_phy_reg_generic+0x10d/0x140
[ 21.479843] [<ffffffff814aedac>]
ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
[ 21.487787] [<ffffffff8145be6f>] ? bond_enslave+0x4ef/0xb80
[ 21.493513] [<ffffffff814a64e4>] ixgbe_get_settings+0x34/0x340
[ 21.499468] [<ffffffff81586ab8>] __ethtool_get_settings+0x88/0x130
[ 21.505767] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
[ 21.512153] [<ffffffff8145bed9>] bond_enslave+0x559/0xb80
[ 21.517677] [<ffffffff8146454f>] bonding_store_slaves+0x16f/0x1c0
[ 21.523889] [<ffffffff813bfb83>] dev_attr_store+0x13/0x30
[ 21.529412] [<ffffffff811c40b4>] sysfs_write_file+0xd4/0x150
[ 21.535193] [<ffffffff81154b81>] vfs_write+0xb1/0x190
[ 21.540373] [<ffffffff81154ee0>] sys_write+0x50/0xa0
[ 21.545463] [<ffffffff81637092>] system_call_fastpath+0x16/0x1b
On Fri, 2013-03-01 at 00:15 -0800, Linda Walsh wrote:
> Just installed 3.8.1....
>
> Thought this had been fixed? Note it causes the kernel to
> show up as tainted after the 1st...
>
CC netdev & Jay Vosburgh & Jeff Kirsher
>
>
> As the system was coming up and initializing the bond0 driver:
>
>
> [ 19.847743] ixgbe 0000:06:00.0: registered PHC device on eth_s2_0
> [ 20.258245] BUG: scheduling while atomic: ifup-bonding/2003/0x00000002
> [ 20.264812] 4 locks held by ifup-bonding/2003:
> [ 20.269298] #0: (&buffer->mutex){......}, at: [<ffffffff811c401f>]
> sysfs_write_file+0x3f/0x150
> [ 20.278319] #1: (s_active#59){......}, at: [<ffffffff811c409b>]
> sysfs_write_file+0xbb/0x150
> [ 20.287088] #2: (rtnl_mutex){......}, at: [<ffffffff81590bf0>]
> rtnl_trylock+0x10/0x20
> [ 20.295373] #3: (&bond->lock){......}, at: [<ffffffff8145be6f>]
> bond_enslave+0x4ef/0xb80
> [ 20.303912] Modules linked in: iptable_filter kvm_intel kvm acpi_cpufreq
> mperf button processor mousedev iTCO_wdt
> [ 20.314695] Pid: 2003, comm: ifup-bonding Not tainted 3.8.1-Isht-Van #5
> [ 20.321340] Call Trace:
> [ 20.323833] [<ffffffff8162b029>] __schedule_bug+0x5e/0x6c
> [ 20.329356] [<ffffffff81634592>] __schedule+0x762/0x7f0
> [ 20.334701] [<ffffffff81634734>] schedule+0x24/0x70
> [ 20.339703] [<ffffffff816336f4>] schedule_hrtimeout_range_clock+0xa4/0x130
> [ 20.346699] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 20.352130] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
> [ 20.358434] [<ffffffff8163378e>] schedule_hrtimeout_range+0xe/0x10
> [ 20.364734] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
> [ 20.370082] [<ffffffff814b2d7c>] ixgbe_acquire_swfw_sync_X540+0xbc/0x100
> [ 20.376905] [<ffffffff814aeb0d>] ixgbe_read_phy_reg_generic+0x3d/0x140
> [ 20.383553] [<ffffffff814aedac>]
> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
> [ 20.391499] [<ffffffff8145be6f>] ? bond_enslave+0x4ef/0xb80
> [ 20.397194] [<ffffffff814a64e4>] ixgbe_get_settings+0x34/0x340
> [ 20.403148] [<ffffffff81586ab8>] __ethtool_get_settings+0x88/0x130
> [ 20.409448] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
> [ 20.415833] [<ffffffff8145bed9>] bond_enslave+0x559/0xb80
> [ 20.421356] [<ffffffff8146454f>] bonding_store_slaves+0x16f/0x1c0
> [ 20.427569] [<ffffffff813bfb83>] dev_attr_store+0x13/0x30
> [ 20.433091] [<ffffffff811c40b4>] sysfs_write_file+0xd4/0x150
> [ 20.438872] [<ffffffff81154b81>] vfs_write+0xb1/0x190
> [ 20.444047] [<ffffffff81154ee0>] sys_write+0x50/0xa0
> [ 20.449137] [<ffffffff81637092>] system_call_fastpath+0x16/0x1b
> [ 20.455264] BUG: scheduling while atomic: ifup-bonding/2003/0x00000002
> [ 20.461851] 4 locks held by ifup-bonding/2003:
> [ 20.466334] #0: (&buffer->mutex){......}, at: [<ffffffff811c401f>]
> sysfs_write_file+0x3f/0x150
> [ 20.475356] #1: (s_active#59){......}, at: [<ffffffff811c409b>]
> sysfs_write_file+0xbb/0x150
> [ 20.484117] #2: (rtnl_mutex){......}, at: [<ffffffff81590bf0>]
> rtnl_trylock+0x10/0x20
> [ 20.492403] #3: (&bond->lock){......}, at: [<ffffffff8145be6f>]
> bond_enslave+0x4ef/0xb80
> [ 20.500902] Modules linked in: iptable_filter kvm_intel kvm acpi_cpufreq
> mperf button processor mousedev iTCO_wdt
> [ 20.511640] Pid: 2003, comm: ifup-bonding Tainted: G W
> 3.8.1-Isht-Van #5
> [ 20.519240] Call Trace:
> [ 20.521729] [<ffffffff8162b029>] __schedule_bug+0x5e/0x6c
> [ 20.527251] [<ffffffff81634592>] __schedule+0x762/0x7f0
> [ 20.532599] [<ffffffff81634734>] schedule+0x24/0x70
> [ 20.537599] [<ffffffff816336f4>] schedule_hrtimeout_range_clock+0xa4/0x130
> [ 20.544592] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 20.550026] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 20.555462] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
> [ 20.561763] [<ffffffff8163378e>] schedule_hrtimeout_range+0xe/0x10
> [ 20.568064] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
> [ 20.573415] [<ffffffff814b2cae>] ixgbe_release_swfw_sync_X540+0x4e/0x60
> [ 20.580146] [<ffffffff814aebdd>] ixgbe_read_phy_reg_generic+0x10d/0x140
> [ 20.586960] [<ffffffff814aedac>]
> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
> [ 20.594908] [<ffffffff8145be6f>] ? bond_enslave+0x4ef/0xb80
> [ 20.600601] [<ffffffff814a64e4>] ixgbe_get_settings+0x34/0x340
> [ 20.606557] [<ffffffff81586ab8>] __ethtool_get_settings+0x88/0x130
> [ 20.612858] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
> [ 20.619244] [<ffffffff8145bed9>] bond_enslave+0x559/0xb80
> [ 20.624767] [<ffffffff8146454f>] bonding_store_slaves+0x16f/0x1c0
> [ 20.630983] [<ffffffff813bfb83>] dev_attr_store+0x13/0x30
> [ 20.636503] [<ffffffff811c40b4>] sysfs_write_file+0xd4/0x150
> [ 20.642283] [<ffffffff81154b81>] vfs_write+0xb1/0x190
> [ 20.647462] [<ffffffff81154ee0>] sys_write+0x50/0xa0
> [ 20.652548] [<ffffffff81637092>] system_call_fastpath+0x16/0x1b
> [ 20.658696] bonding: bond0: enslaving eth_s2_0 as an active interface with a
> down link.
> [ 20.676577] bonding: bond0: Adding slave eth_s2_1.
> [ 20.743760] pps pps1: new PPS source ptp1
> [ 20.747792] ixgbe 0000:06:00.1: registered PHC device on eth_s2_1
> [ 21.150267] BUG: scheduling while atomic: ifup-bonding/2003/0x00000002
> [ 21.156836] 4 locks held by ifup-bonding/2003:
> [ 21.161319] #0: (&buffer->mutex){......}, at: [<ffffffff811c401f>]
> sysfs_write_file+0x3f/0x150
> [ 21.170388] #1: (s_active#59){......}, at: [<ffffffff811c409b>]
> sysfs_write_file+0xbb/0x150
> [ 21.179149] #2: (rtnl_mutex){......}, at: [<ffffffff81590bf0>]
> rtnl_trylock+0x10/0x20
> [ 21.187403] #3: (&bond->lock){......}, at: [<ffffffff8145be6f>]
> bond_enslave+0x4ef/0xb80
> [ 21.195904] Modules linked in: iptable_filter kvm_intel kvm acpi_cpufreq
> mperf button processor mousedev iTCO_wdt
> [ 21.206644] Pid: 2003, comm: ifup-bonding Tainted: G W
> 3.8.1-Isht-Van #5
> [ 21.214240] Call Trace:
> [ 21.216732] [<ffffffff8162b029>] __schedule_bug+0x5e/0x6c
> [ 21.222254] [<ffffffff81634592>] __schedule+0x762/0x7f0
> [ 21.227604] [<ffffffff81634734>] schedule+0x24/0x70
> [ 21.232606] [<ffffffff816336f4>] schedule_hrtimeout_range_clock+0xa4/0x130
> [ 21.239601] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 21.245033] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
> [ 21.251339] [<ffffffff8163378e>] schedule_hrtimeout_range+0xe/0x10
> [ 21.257635] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
> [ 21.262987] [<ffffffff814b2d7c>] ixgbe_acquire_swfw_sync_X540+0xbc/0x100
> [ 21.269811] [<ffffffff814aeb0d>] ixgbe_read_phy_reg_generic+0x3d/0x140
> [ 21.276461] [<ffffffff814aedac>]
> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
> [ 21.284409] [<ffffffff8145be6f>] ? bond_enslave+0x4ef/0xb80
> [ 21.290106] [<ffffffff814a64e4>] ixgbe_get_settings+0x34/0x340
> [ 21.296067] [<ffffffff81586ab8>] __ethtool_get_settings+0x88/0x130
> [ 21.302369] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
> [ 21.308754] [<ffffffff8145bed9>] bond_enslave+0x559/0xb80
> [ 21.314278] [<ffffffff8146454f>] bonding_store_slaves+0x16f/0x1c0
> [ 21.320491] [<ffffffff813bfb83>] dev_attr_store+0x13/0x30
> [ 21.326009] [<ffffffff811c40b4>] sysfs_write_file+0xd4/0x150
> [ 21.331793] [<ffffffff81154b81>] vfs_write+0xb1/0x190
> [ 21.336964] [<ffffffff81154ee0>] sys_write+0x50/0xa0
> [ 21.342053] [<ffffffff81637092>] system_call_fastpath+0x16/0x1b
> [ 21.348191] BUG: scheduling while atomic: ifup-bonding/2003/0x00000002
> [ 21.354775] 4 locks held by ifup-bonding/2003:
> [ 21.359258] #0: (&buffer->mutex){......}, at: [<ffffffff811c401f>]
> sysfs_write_file+0x3f/0x150
> [ 21.368283] #1: (s_active#59){......}, at: [<ffffffff811c409b>]
> sysfs_write_file+0xbb/0x150
> [ 21.377104] #2: (rtnl_mutex){......}, at: [<ffffffff81590bf0>]
> rtnl_trylock+0x10/0x20
> [ 21.385343] #3: (&bond->lock){......}, at: [<ffffffff8145be6f>]
> bond_enslave+0x4ef/0xb80
> [ 21.393887] Modules linked in: iptable_filter kvm_intel kvm acpi_cpufreq
> mperf button processor mousedev iTCO_wdt
> [ 21.404575] Pid: 2003, comm: ifup-bonding Tainted: G W
> 3.8.1-Isht-Van #5
> [ 21.412176] Call Trace:
> [ 21.414666] [<ffffffff8162b029>] __schedule_bug+0x5e/0x6c
> [ 21.420188] [<ffffffff81634592>] __schedule+0x762/0x7f0
> [ 21.425536] [<ffffffff81634734>] schedule+0x24/0x70
> [ 21.430541] [<ffffffff816336f4>] schedule_hrtimeout_range_clock+0xa4/0x130
> [ 21.437532] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 21.442967] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 21.448407] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
> [ 21.454712] [<ffffffff8163378e>] schedule_hrtimeout_range+0xe/0x10
> [ 21.461015] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
> [ 21.466370] [<ffffffff814b2cae>] ixgbe_release_swfw_sync_X540+0x4e/0x60
> [ 21.473105] [<ffffffff814aebdd>] ixgbe_read_phy_reg_generic+0x10d/0x140
> [ 21.479843] [<ffffffff814aedac>]
> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
> [ 21.487787] [<ffffffff8145be6f>] ? bond_enslave+0x4ef/0xb80
> [ 21.493513] [<ffffffff814a64e4>] ixgbe_get_settings+0x34/0x340
> [ 21.499468] [<ffffffff81586ab8>] __ethtool_get_settings+0x88/0x130
> [ 21.505767] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
> [ 21.512153] [<ffffffff8145bed9>] bond_enslave+0x559/0xb80
> [ 21.517677] [<ffffffff8146454f>] bonding_store_slaves+0x16f/0x1c0
> [ 21.523889] [<ffffffff813bfb83>] dev_attr_store+0x13/0x30
> [ 21.529412] [<ffffffff811c40b4>] sysfs_write_file+0xd4/0x150
> [ 21.535193] [<ffffffff81154b81>] vfs_write+0xb1/0x190
> [ 21.540373] [<ffffffff81154ee0>] sys_write+0x50/0xa0
> [ 21.545463] [<ffffffff81637092>] system_call_fastpath+0x16/0x1b
> --
Linda Walsh wrote:
>
>
> This patch is not in the latest kernel. I don't know if it is the
> 'best' way, but it does stop BUG error messages.
---
Update -- it *used* to stop the messages in 3.6.7.
It no longer stops the messages in 3.8.1 -- (and isn't present by
default -- tried
adding the unlock/lock -- no difference.
Weird. *sigh*
>
>
> -------- Original Message --------
> Subject: Re: BUG: scheduling while atomic:
> ifup-bonding/3711/0x00000002 -- V3.6.7
> Date: Wed, 28 Nov 2012 13:17:31 -0800
> From: Linda Walsh <[email protected]>
> To: Cong Wang <[email protected]>
> CC: LKML <[email protected]>, Linux Kernel Network
> Developers <[email protected]>
> References: <[email protected]>
> <CAM_iQpUW2Oz9p0K0gGKc6JoD7WAu0kJtRa4uBSe+WfXg0Nn3jA@mail.gmail.com>
>
>
>
> Cong Wang wrote:
>> Does this quick fix help?
>> diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c
>> index 5f5b69f..4a4d9eb 100644
>> --- a/drivers/net/bonding/bond_main.c
>> +++ b/drivers/net/bonding/bond_main.c
>> @@ -1785,7 +1785,9 @@ int bond_enslave(struct net_device *bond_dev,
>> struct net_device *slave_dev)
>> new_slave->link == BOND_LINK_DOWN ? "DOWN" :
>> (new_slave->link == BOND_LINK_UP ? "UP" : "BACK"));
>>
>> + read_unlock(&bond->lock);
>> bond_update_speed_duplex(new_slave);
>> + read_lock(&bond->lock);
>>
>> if (USES_PRIMARY(bond->params.mode) && bond->params.primary[0]) {
>> /* if there is a primary slave, remember it */
>>
>> Thanks!
>>
>
>
>
>
> Eric Dumazet wrote:
>> On Fri, 2013-03-01 at 00:15 -0800, Linda Walsh wrote:
>>
>>> Just installed 3.8.1....
>>>
>>> Thought this had been fixed? Note it causes the kernel to
>>> show up as tainted after the 1st...
>>>
>>>
>>
>> CC netdev & Jay Vosburgh & Jeff Kirsher
>>
>>
>>> As the system was coming up and initializing the bond0 driver:
>>>
>>>
>>> [ 19.847743] ixgbe 0000:06:00.0: registered PHC device on eth_s2_0
>>> [ 20.258245] BUG: scheduling while atomic: ifup-bonding/2003/0x00000002
>>> [ 20.264812] 4 locks held by ifup-bonding/2003:
>>> [ 20.269298] #0: (&buffer->mutex){......}, at: [<ffffffff811c401f>]
>>> sysfs_write_file+0x3f/0x150
>>> [ 20.278319] #1: (s_active#59){......}, at: [<ffffffff811c409b>]
>>> sysfs_write_file+0xbb/0x150
>>> [ 20.287088] #2: (rtnl_mutex){......}, at: [<ffffffff81590bf0>]
>>> rtnl_trylock+0x10/0x20
>>> [ 20.295373] #3: (&bond->lock){......}, at: [<ffffffff8145be6f>]
>>> bond_enslave+0x4ef/0xb80
>>> [ 20.303912] Modules linked in: iptable_filter kvm_intel kvm acpi_cpufreq
>>> mperf button processor mousedev iTCO_wdt
>>> [ 20.314695] Pid: 2003, comm: ifup-bonding Not tainted 3.8.1-Isht-Van #5
>>> [ 20.321340] Call Trace:
>>> [ 20.323833] [<ffffffff8162b029>] __schedule_bug+0x5e/0x6c
>>> [ 20.329356] [<ffffffff81634592>] __schedule+0x762/0x7f0
>>> [ 20.334701] [<ffffffff81634734>] schedule+0x24/0x70
>>> [ 20.339703] [<ffffffff816336f4>] schedule_hrtimeout_range_clock+0xa4/0x130
>>> [ 20.346699] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
>>> [ 20.352130] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
>>> [ 20.358434] [<ffffffff8163378e>] schedule_hrtimeout_range+0xe/0x10
>>> [ 20.364734] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
>>> [ 20.370082] [<ffffffff814b2d7c>] ixgbe_acquire_swfw_sync_X540+0xbc/0x100
>>> [ 20.376905] [<ffffffff814aeb0d>] ixgbe_read_phy_reg_generic+0x3d/0x140
>>> [ 20.383553] [<ffffffff814aedac>]
>>> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
>>> [ 20.391499] [<ffffffff8145be6f>] ? bond_enslave+0x4ef/0xb80
>>> [ 20.397194] [<ffffffff814a64e4>] ixgbe_get_settings+0x34/0x340
>>> [ 20.403148] [<ffffffff81586ab8>] __ethtool_get_settings+0x88/0x130
>>> [ 20.409448] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
>>> [ 20.415833] [<ffffffff8145bed9>] bond_enslave+0x559/0xb80
>>> [ 20.421356] [<ffffffff8146454f>] bonding_store_slaves+0x16f/0x1c0
>>> [ 20.427569] [<ffffffff813bfb83>] dev_attr_store+0x13/0x30
>>> [ 20.433091] [<ffffffff811c40b4>] sysfs_write_file+0xd4/0x150
>>> [ 20.438872] [<ffffffff81154b81>] vfs_write+0xb1/0x190
>>> [ 20.444047] [<ffffffff81154ee0>] sys_write+0x50/0xa0
>>> [ 20.449137] [<ffffffff81637092>] system_call_fastpath+0x16/0x1b
>>> [ 20.455264] BUG: scheduling while atomic: ifup-bonding/2003/0x00000002
>>> [ 20.461851] 4 locks held by ifup-bonding/2003:
>>> [ 20.466334] #0: (&buffer->mutex){......}, at: [<ffffffff811c401f>]
>>> sysfs_write_file+0x3f/0x150
>>> [ 20.475356] #1: (s_active#59){......}, at: [<ffffffff811c409b>]
>>> sysfs_write_file+0xbb/0x150
>>> [ 20.484117] #2: (rtnl_mutex){......}, at: [<ffffffff81590bf0>]
>>> rtnl_trylock+0x10/0x20
>>> [ 20.492403] #3: (&bond->lock){......}, at: [<ffffffff8145be6f>]
>>> bond_enslave+0x4ef/0xb80
>>> [ 20.500902] Modules linked in: iptable_filter kvm_intel kvm acpi_cpufreq
>>> mperf button processor mousedev iTCO_wdt
>>> [ 20.511640] Pid: 2003, comm: ifup-bonding Tainted: G W
>>> 3.8.1-Isht-Van #5
>>> [ 20.519240] Call Trace:
>>> [ 20.521729] [<ffffffff8162b029>] __schedule_bug+0x5e/0x6c
>>> [ 20.527251] [<ffffffff81634592>] __schedule+0x762/0x7f0
>>> [ 20.532599] [<ffffffff81634734>] schedule+0x24/0x70
>>> [ 20.537599] [<ffffffff816336f4>] schedule_hrtimeout_range_clock+0xa4/0x130
>>> [ 20.544592] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
>>> [ 20.550026] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
>>> [ 20.555462] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
>>> [ 20.561763] [<ffffffff8163378e>] schedule_hrtimeout_range+0xe/0x10
>>> [ 20.568064] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
>>> [ 20.573415] [<ffffffff814b2cae>] ixgbe_release_swfw_sync_X540+0x4e/0x60
>>> [ 20.580146] [<ffffffff814aebdd>] ixgbe_read_phy_reg_generic+0x10d/0x140
>>> [ 20.586960] [<ffffffff814aedac>]
>>> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
>>> [ 20.594908] [<ffffffff8145be6f>] ? bond_enslave+0x4ef/0xb80
>>> [ 20.600601] [<ffffffff814a64e4>] ixgbe_get_settings+0x34/0x340
>>> [ 20.606557] [<ffffffff81586ab8>] __ethtool_get_settings+0x88/0x130
>>> [ 20.612858] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
>>> [ 20.619244] [<ffffffff8145bed9>] bond_enslave+0x559/0xb80
>>> [ 20.624767] [<ffffffff8146454f>] bonding_store_slaves+0x16f/0x1c0
>>> [ 20.630983] [<ffffffff813bfb83>] dev_attr_store+0x13/0x30
>>> [ 20.636503] [<ffffffff811c40b4>] sysfs_write_file+0xd4/0x150
>>> [ 20.642283] [<ffffffff81154b81>] vfs_write+0xb1/0x190
>>> [ 20.647462] [<ffffffff81154ee0>] sys_write+0x50/0xa0
>>> [ 20.652548] [<ffffffff81637092>] system_call_fastpath+0x16/0x1b
>>> [ 20.658696] bonding: bond0: enslaving eth_s2_0 as an active interface with a
>>> down link.
>>> [ 20.676577] bonding: bond0: Adding slave eth_s2_1.
>>> [ 20.743760] pps pps1: new PPS source ptp1
>>> [ 20.747792] ixgbe 0000:06:00.1: registered PHC device on eth_s2_1
>>> [ 21.150267] BUG: scheduling while atomic: ifup-bonding/2003/0x00000002
>>> [ 21.156836] 4 locks held by ifup-bonding/2003:
>>> [ 21.161319] #0: (&buffer->mutex){......}, at: [<ffffffff811c401f>]
>>> sysfs_write_file+0x3f/0x150
>>> [ 21.170388] #1: (s_active#59){......}, at: [<ffffffff811c409b>]
>>> sysfs_write_file+0xbb/0x150
>>> [ 21.179149] #2: (rtnl_mutex){......}, at: [<ffffffff81590bf0>]
>>> rtnl_trylock+0x10/0x20
>>> [ 21.187403] #3: (&bond->lock){......}, at: [<ffffffff8145be6f>]
>>> bond_enslave+0x4ef/0xb80
>>> [ 21.195904] Modules linked in: iptable_filter kvm_intel kvm acpi_cpufreq
>>> mperf button processor mousedev iTCO_wdt
>>> [ 21.206644] Pid: 2003, comm: ifup-bonding Tainted: G W
>>> 3.8.1-Isht-Van #5
>>> [ 21.214240] Call Trace:
>>> [ 21.216732] [<ffffffff8162b029>] __schedule_bug+0x5e/0x6c
>>> [ 21.222254] [<ffffffff81634592>] __schedule+0x762/0x7f0
>>> [ 21.227604] [<ffffffff81634734>] schedule+0x24/0x70
>>> [ 21.232606] [<ffffffff816336f4>] schedule_hrtimeout_range_clock+0xa4/0x130
>>> [ 21.239601] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
>>> [ 21.245033] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
>>> [ 21.251339] [<ffffffff8163378e>] schedule_hrtimeout_range+0xe/0x10
>>> [ 21.257635] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
>>> [ 21.262987] [<ffffffff814b2d7c>] ixgbe_acquire_swfw_sync_X540+0xbc/0x100
>>> [ 21.269811] [<ffffffff814aeb0d>] ixgbe_read_phy_reg_generic+0x3d/0x140
>>> [ 21.276461] [<ffffffff814aedac>]
>>> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
>>> [ 21.284409] [<ffffffff8145be6f>] ? bond_enslave+0x4ef/0xb80
>>> [ 21.290106] [<ffffffff814a64e4>] ixgbe_get_settings+0x34/0x340
>>> [ 21.296067] [<ffffffff81586ab8>] __ethtool_get_settings+0x88/0x130
>>> [ 21.302369] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
>>> [ 21.308754] [<ffffffff8145bed9>] bond_enslave+0x559/0xb80
>>> [ 21.314278] [<ffffffff8146454f>] bonding_store_slaves+0x16f/0x1c0
>>> [ 21.320491] [<ffffffff813bfb83>] dev_attr_store+0x13/0x30
>>> [ 21.326009] [<ffffffff811c40b4>] sysfs_write_file+0xd4/0x150
>>> [ 21.331793] [<ffffffff81154b81>] vfs_write+0xb1/0x190
>>> [ 21.336964] [<ffffffff81154ee0>] sys_write+0x50/0xa0
>>> [ 21.342053] [<ffffffff81637092>] system_call_fastpath+0x16/0x1b
>>> [ 21.348191] BUG: scheduling while atomic: ifup-bonding/2003/0x00000002
>>> [ 21.354775] 4 locks held by ifup-bonding/2003:
>>> [ 21.359258] #0: (&buffer->mutex){......}, at: [<ffffffff811c401f>]
>>> sysfs_write_file+0x3f/0x150
>>> [ 21.368283] #1: (s_active#59){......}, at: [<ffffffff811c409b>]
>>> sysfs_write_file+0xbb/0x150
>>> [ 21.377104] #2: (rtnl_mutex){......}, at: [<ffffffff81590bf0>]
>>> rtnl_trylock+0x10/0x20
>>> [ 21.385343] #3: (&bond->lock){......}, at: [<ffffffff8145be6f>]
>>> bond_enslave+0x4ef/0xb80
>>> [ 21.393887] Modules linked in: iptable_filter kvm_intel kvm acpi_cpufreq
>>> mperf button processor mousedev iTCO_wdt
>>> [ 21.404575] Pid: 2003, comm: ifup-bonding Tainted: G W
>>> 3.8.1-Isht-Van #5
>>> [ 21.412176] Call Trace:
>>> [ 21.414666] [<ffffffff8162b029>] __schedule_bug+0x5e/0x6c
>>> [ 21.420188] [<ffffffff81634592>] __schedule+0x762/0x7f0
>>> [ 21.425536] [<ffffffff81634734>] schedule+0x24/0x70
>>> [ 21.430541] [<ffffffff816336f4>] schedule_hrtimeout_range_clock+0xa4/0x130
>>> [ 21.437532] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
>>> [ 21.442967] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
>>> [ 21.448407] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
>>> [ 21.454712] [<ffffffff8163378e>] schedule_hrtimeout_range+0xe/0x10
>>> [ 21.461015] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
>>> [ 21.466370] [<ffffffff814b2cae>] ixgbe_release_swfw_sync_X540+0x4e/0x60
>>> [ 21.473105] [<ffffffff814aebdd>] ixgbe_read_phy_reg_generic+0x10d/0x140
>>> [ 21.479843] [<ffffffff814aedac>]
>>> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
>>> [ 21.487787] [<ffffffff8145be6f>] ? bond_enslave+0x4ef/0xb80
>>> [ 21.493513] [<ffffffff814a64e4>] ixgbe_get_settings+0x34/0x340
>>> [ 21.499468] [<ffffffff81586ab8>] __ethtool_get_settings+0x88/0x130
>>> [ 21.505767] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
>>> [ 21.512153] [<ffffffff8145bed9>] bond_enslave+0x559/0xb80
>>> [ 21.517677] [<ffffffff8146454f>] bonding_store_slaves+0x16f/0x1c0
>>> [ 21.523889] [<ffffffff813bfb83>] dev_attr_store+0x13/0x30
>>> [ 21.529412] [<ffffffff811c40b4>] sysfs_write_file+0xd4/0x150
>>> [ 21.535193] [<ffffffff81154b81>] vfs_write+0xb1/0x190
>>> [ 21.540373] [<ffffffff81154ee0>] sys_write+0x50/0xa0
>>> [ 21.545463] [<ffffffff81637092>] system_call_fastpath+0x16/0x1b
>>> --
>>>
>>
>>
>
On 03/02/2013 01:21 PM, Linda Walsh wrote:
>
>
>
>
> Linda Walsh wrote:
>>
>>
>> This patch is not in the latest kernel. I don't know if it is the
>> 'best' way, but it does stop BUG error messages.
> ---
> Update -- it *used* to stop the messages in 3.6.7.
>
> It no longer stops the messages in 3.8.1 -- (and isn't present by
> default -- tried
> adding the unlock/lock -- no difference.
>
> Weird. *sigh*
Hi, Linda
Do you have the BUG log after applied this patch?
bond->lock seems to be the only one who will add the preempt_count, the
patch should works...
And have you tried the 3.9.0-rc1, is the issue still exist?
Regards,
Michael Wang
>
>>
>>
>> -------- Original Message --------
>> Subject: Re: BUG: scheduling while atomic:
>> ifup-bonding/3711/0x00000002 -- V3.6.7
>> Date: Wed, 28 Nov 2012 13:17:31 -0800
>> From: Linda Walsh <[email protected]>
>> To: Cong Wang <[email protected]>
>> CC: LKML <[email protected]>, Linux Kernel Network
>> Developers <[email protected]>
>> References: <[email protected]>
>> <CAM_iQpUW2Oz9p0K0gGKc6JoD7WAu0kJtRa4uBSe+WfXg0Nn3jA@mail.gmail.com>
>>
>>
>>
>> Cong Wang wrote:
>>> Does this quick fix help?
>>> diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c
>>> index 5f5b69f..4a4d9eb 100644
>>> --- a/drivers/net/bonding/bond_main.c
>>> +++ b/drivers/net/bonding/bond_main.c
>>> @@ -1785,7 +1785,9 @@ int bond_enslave(struct net_device *bond_dev,
>>> struct net_device *slave_dev)
>>> new_slave->link == BOND_LINK_DOWN ? "DOWN" :
>>> (new_slave->link == BOND_LINK_UP ? "UP" : "BACK"));
>>>
>>> + read_unlock(&bond->lock);
>>> bond_update_speed_duplex(new_slave);
>>> + read_lock(&bond->lock);
>>>
>>> if (USES_PRIMARY(bond->params.mode) && bond->params.primary[0]) {
>>> /* if there is a primary slave, remember it */
>>>
>>> Thanks!
>>>
>>
>>
>>
>>
>> Eric Dumazet wrote:
>>> On Fri, 2013-03-01 at 00:15 -0800, Linda Walsh wrote:
>>>
>>>> Just installed 3.8.1....
>>>>
>>>> Thought this had been fixed? Note it causes the kernel to
>>>> show up as tainted after the 1st...
>>>>
>>>>
>>>
>>> CC netdev & Jay Vosburgh & Jeff Kirsher
>>>
>>>
>>>> As the system was coming up and initializing the bond0 driver:
>>>>
>>>>
>>>> [ 19.847743] ixgbe 0000:06:00.0: registered PHC device on eth_s2_0
>>>> [ 20.258245] BUG: scheduling while atomic: ifup-bonding/2003/0x00000002
>>>> [ 20.264812] 4 locks held by ifup-bonding/2003:
>>>> [ 20.269298] #0: (&buffer->mutex){......}, at: [<ffffffff811c401f>]
>>>> sysfs_write_file+0x3f/0x150
>>>> [ 20.278319] #1: (s_active#59){......}, at: [<ffffffff811c409b>]
>>>> sysfs_write_file+0xbb/0x150
>>>> [ 20.287088] #2: (rtnl_mutex){......}, at: [<ffffffff81590bf0>]
>>>> rtnl_trylock+0x10/0x20
>>>> [ 20.295373] #3: (&bond->lock){......}, at: [<ffffffff8145be6f>]
>>>> bond_enslave+0x4ef/0xb80
>>>> [ 20.303912] Modules linked in: iptable_filter kvm_intel kvm acpi_cpufreq
>>>> mperf button processor mousedev iTCO_wdt
>>>> [ 20.314695] Pid: 2003, comm: ifup-bonding Not tainted 3.8.1-Isht-Van #5
>>>> [ 20.321340] Call Trace:
>>>> [ 20.323833] [<ffffffff8162b029>] __schedule_bug+0x5e/0x6c
>>>> [ 20.329356] [<ffffffff81634592>] __schedule+0x762/0x7f0
>>>> [ 20.334701] [<ffffffff81634734>] schedule+0x24/0x70
>>>> [ 20.339703] [<ffffffff816336f4>] schedule_hrtimeout_range_clock+0xa4/0x130
>>>> [ 20.346699] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
>>>> [ 20.352130] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
>>>> [ 20.358434] [<ffffffff8163378e>] schedule_hrtimeout_range+0xe/0x10
>>>> [ 20.364734] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
>>>> [ 20.370082] [<ffffffff814b2d7c>] ixgbe_acquire_swfw_sync_X540+0xbc/0x100
>>>> [ 20.376905] [<ffffffff814aeb0d>] ixgbe_read_phy_reg_generic+0x3d/0x140
>>>> [ 20.383553] [<ffffffff814aedac>]
>>>> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
>>>> [ 20.391499] [<ffffffff8145be6f>] ? bond_enslave+0x4ef/0xb80
>>>> [ 20.397194] [<ffffffff814a64e4>] ixgbe_get_settings+0x34/0x340
>>>> [ 20.403148] [<ffffffff81586ab8>] __ethtool_get_settings+0x88/0x130
>>>> [ 20.409448] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
>>>> [ 20.415833] [<ffffffff8145bed9>] bond_enslave+0x559/0xb80
>>>> [ 20.421356] [<ffffffff8146454f>] bonding_store_slaves+0x16f/0x1c0
>>>> [ 20.427569] [<ffffffff813bfb83>] dev_attr_store+0x13/0x30
>>>> [ 20.433091] [<ffffffff811c40b4>] sysfs_write_file+0xd4/0x150
>>>> [ 20.438872] [<ffffffff81154b81>] vfs_write+0xb1/0x190
>>>> [ 20.444047] [<ffffffff81154ee0>] sys_write+0x50/0xa0
>>>> [ 20.449137] [<ffffffff81637092>] system_call_fastpath+0x16/0x1b
>>>> [ 20.455264] BUG: scheduling while atomic: ifup-bonding/2003/0x00000002
>>>> [ 20.461851] 4 locks held by ifup-bonding/2003:
>>>> [ 20.466334] #0: (&buffer->mutex){......}, at: [<ffffffff811c401f>]
>>>> sysfs_write_file+0x3f/0x150
>>>> [ 20.475356] #1: (s_active#59){......}, at: [<ffffffff811c409b>]
>>>> sysfs_write_file+0xbb/0x150
>>>> [ 20.484117] #2: (rtnl_mutex){......}, at: [<ffffffff81590bf0>]
>>>> rtnl_trylock+0x10/0x20
>>>> [ 20.492403] #3: (&bond->lock){......}, at: [<ffffffff8145be6f>]
>>>> bond_enslave+0x4ef/0xb80
>>>> [ 20.500902] Modules linked in: iptable_filter kvm_intel kvm acpi_cpufreq
>>>> mperf button processor mousedev iTCO_wdt
>>>> [ 20.511640] Pid: 2003, comm: ifup-bonding Tainted: G W
>>>> 3.8.1-Isht-Van #5
>>>> [ 20.519240] Call Trace:
>>>> [ 20.521729] [<ffffffff8162b029>] __schedule_bug+0x5e/0x6c
>>>> [ 20.527251] [<ffffffff81634592>] __schedule+0x762/0x7f0
>>>> [ 20.532599] [<ffffffff81634734>] schedule+0x24/0x70
>>>> [ 20.537599] [<ffffffff816336f4>] schedule_hrtimeout_range_clock+0xa4/0x130
>>>> [ 20.544592] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
>>>> [ 20.550026] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
>>>> [ 20.555462] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
>>>> [ 20.561763] [<ffffffff8163378e>] schedule_hrtimeout_range+0xe/0x10
>>>> [ 20.568064] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
>>>> [ 20.573415] [<ffffffff814b2cae>] ixgbe_release_swfw_sync_X540+0x4e/0x60
>>>> [ 20.580146] [<ffffffff814aebdd>] ixgbe_read_phy_reg_generic+0x10d/0x140
>>>> [ 20.586960] [<ffffffff814aedac>]
>>>> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
>>>> [ 20.594908] [<ffffffff8145be6f>] ? bond_enslave+0x4ef/0xb80
>>>> [ 20.600601] [<ffffffff814a64e4>] ixgbe_get_settings+0x34/0x340
>>>> [ 20.606557] [<ffffffff81586ab8>] __ethtool_get_settings+0x88/0x130
>>>> [ 20.612858] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
>>>> [ 20.619244] [<ffffffff8145bed9>] bond_enslave+0x559/0xb80
>>>> [ 20.624767] [<ffffffff8146454f>] bonding_store_slaves+0x16f/0x1c0
>>>> [ 20.630983] [<ffffffff813bfb83>] dev_attr_store+0x13/0x30
>>>> [ 20.636503] [<ffffffff811c40b4>] sysfs_write_file+0xd4/0x150
>>>> [ 20.642283] [<ffffffff81154b81>] vfs_write+0xb1/0x190
>>>> [ 20.647462] [<ffffffff81154ee0>] sys_write+0x50/0xa0
>>>> [ 20.652548] [<ffffffff81637092>] system_call_fastpath+0x16/0x1b
>>>> [ 20.658696] bonding: bond0: enslaving eth_s2_0 as an active interface with a
>>>> down link.
>>>> [ 20.676577] bonding: bond0: Adding slave eth_s2_1.
>>>> [ 20.743760] pps pps1: new PPS source ptp1
>>>> [ 20.747792] ixgbe 0000:06:00.1: registered PHC device on eth_s2_1
>>>> [ 21.150267] BUG: scheduling while atomic: ifup-bonding/2003/0x00000002
>>>> [ 21.156836] 4 locks held by ifup-bonding/2003:
>>>> [ 21.161319] #0: (&buffer->mutex){......}, at: [<ffffffff811c401f>]
>>>> sysfs_write_file+0x3f/0x150
>>>> [ 21.170388] #1: (s_active#59){......}, at: [<ffffffff811c409b>]
>>>> sysfs_write_file+0xbb/0x150
>>>> [ 21.179149] #2: (rtnl_mutex){......}, at: [<ffffffff81590bf0>]
>>>> rtnl_trylock+0x10/0x20
>>>> [ 21.187403] #3: (&bond->lock){......}, at: [<ffffffff8145be6f>]
>>>> bond_enslave+0x4ef/0xb80
>>>> [ 21.195904] Modules linked in: iptable_filter kvm_intel kvm acpi_cpufreq
>>>> mperf button processor mousedev iTCO_wdt
>>>> [ 21.206644] Pid: 2003, comm: ifup-bonding Tainted: G W
>>>> 3.8.1-Isht-Van #5
>>>> [ 21.214240] Call Trace:
>>>> [ 21.216732] [<ffffffff8162b029>] __schedule_bug+0x5e/0x6c
>>>> [ 21.222254] [<ffffffff81634592>] __schedule+0x762/0x7f0
>>>> [ 21.227604] [<ffffffff81634734>] schedule+0x24/0x70
>>>> [ 21.232606] [<ffffffff816336f4>] schedule_hrtimeout_range_clock+0xa4/0x130
>>>> [ 21.239601] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
>>>> [ 21.245033] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
>>>> [ 21.251339] [<ffffffff8163378e>] schedule_hrtimeout_range+0xe/0x10
>>>> [ 21.257635] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
>>>> [ 21.262987] [<ffffffff814b2d7c>] ixgbe_acquire_swfw_sync_X540+0xbc/0x100
>>>> [ 21.269811] [<ffffffff814aeb0d>] ixgbe_read_phy_reg_generic+0x3d/0x140
>>>> [ 21.276461] [<ffffffff814aedac>]
>>>> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
>>>> [ 21.284409] [<ffffffff8145be6f>] ? bond_enslave+0x4ef/0xb80
>>>> [ 21.290106] [<ffffffff814a64e4>] ixgbe_get_settings+0x34/0x340
>>>> [ 21.296067] [<ffffffff81586ab8>] __ethtool_get_settings+0x88/0x130
>>>> [ 21.302369] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
>>>> [ 21.308754] [<ffffffff8145bed9>] bond_enslave+0x559/0xb80
>>>> [ 21.314278] [<ffffffff8146454f>] bonding_store_slaves+0x16f/0x1c0
>>>> [ 21.320491] [<ffffffff813bfb83>] dev_attr_store+0x13/0x30
>>>> [ 21.326009] [<ffffffff811c40b4>] sysfs_write_file+0xd4/0x150
>>>> [ 21.331793] [<ffffffff81154b81>] vfs_write+0xb1/0x190
>>>> [ 21.336964] [<ffffffff81154ee0>] sys_write+0x50/0xa0
>>>> [ 21.342053] [<ffffffff81637092>] system_call_fastpath+0x16/0x1b
>>>> [ 21.348191] BUG: scheduling while atomic: ifup-bonding/2003/0x00000002
>>>> [ 21.354775] 4 locks held by ifup-bonding/2003:
>>>> [ 21.359258] #0: (&buffer->mutex){......}, at: [<ffffffff811c401f>]
>>>> sysfs_write_file+0x3f/0x150
>>>> [ 21.368283] #1: (s_active#59){......}, at: [<ffffffff811c409b>]
>>>> sysfs_write_file+0xbb/0x150
>>>> [ 21.377104] #2: (rtnl_mutex){......}, at: [<ffffffff81590bf0>]
>>>> rtnl_trylock+0x10/0x20
>>>> [ 21.385343] #3: (&bond->lock){......}, at: [<ffffffff8145be6f>]
>>>> bond_enslave+0x4ef/0xb80
>>>> [ 21.393887] Modules linked in: iptable_filter kvm_intel kvm acpi_cpufreq
>>>> mperf button processor mousedev iTCO_wdt
>>>> [ 21.404575] Pid: 2003, comm: ifup-bonding Tainted: G W
>>>> 3.8.1-Isht-Van #5
>>>> [ 21.412176] Call Trace:
>>>> [ 21.414666] [<ffffffff8162b029>] __schedule_bug+0x5e/0x6c
>>>> [ 21.420188] [<ffffffff81634592>] __schedule+0x762/0x7f0
>>>> [ 21.425536] [<ffffffff81634734>] schedule+0x24/0x70
>>>> [ 21.430541] [<ffffffff816336f4>] schedule_hrtimeout_range_clock+0xa4/0x130
>>>> [ 21.437532] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
>>>> [ 21.442967] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
>>>> [ 21.448407] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
>>>> [ 21.454712] [<ffffffff8163378e>] schedule_hrtimeout_range+0xe/0x10
>>>> [ 21.461015] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
>>>> [ 21.466370] [<ffffffff814b2cae>] ixgbe_release_swfw_sync_X540+0x4e/0x60
>>>> [ 21.473105] [<ffffffff814aebdd>] ixgbe_read_phy_reg_generic+0x10d/0x140
>>>> [ 21.479843] [<ffffffff814aedac>]
>>>> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
>>>> [ 21.487787] [<ffffffff8145be6f>] ? bond_enslave+0x4ef/0xb80
>>>> [ 21.493513] [<ffffffff814a64e4>] ixgbe_get_settings+0x34/0x340
>>>> [ 21.499468] [<ffffffff81586ab8>] __ethtool_get_settings+0x88/0x130
>>>> [ 21.505767] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
>>>> [ 21.512153] [<ffffffff8145bed9>] bond_enslave+0x559/0xb80
>>>> [ 21.517677] [<ffffffff8146454f>] bonding_store_slaves+0x16f/0x1c0
>>>> [ 21.523889] [<ffffffff813bfb83>] dev_attr_store+0x13/0x30
>>>> [ 21.529412] [<ffffffff811c40b4>] sysfs_write_file+0xd4/0x150
>>>> [ 21.535193] [<ffffffff81154b81>] vfs_write+0xb1/0x190
>>>> [ 21.540373] [<ffffffff81154ee0>] sys_write+0x50/0xa0
>>>> [ 21.545463] [<ffffffff81637092>] system_call_fastpath+0x16/0x1b
>>>> --
>>>>
>>>
>>>
>>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
Michael Wang wrote:
> On 03/02/2013 01:21 PM, Linda Walsh wrote:
> Update -- it *used* to stop the messages in 3.6.7.
>
> It no longer stops the messages in 3.8.1 -- (and isn't present by
> default -- tried
> adding the unlock/lock -- no difference.
>
> Weird. *sigh*
>
> Hi, Linda
>
> Do you have the BUG log after applied this patch?
>
> bond->lock seems to be the only one who will add the preempt_count, the
> patch should works...
>
> And have you tried the 3.9.0-rc1, is the issue still exist?
>
> Regards,
> Michael Wang
-------------------
What do you mean by 'bug log', do you mean kernel log --- including
the log from boot, in case anything weird pops out, but bug happens
edited out stretch of repetitious looking stuff that was unlikely to
be related...
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.8.1-Isht-Van (law@Ishtar) (gcc version
4.6.2 (SUSE Linux) ) #6 SMP PREEMPT Fri Mar 1 20:29:32 PST 2013
[ 0.000000] Command line: BOOT_IMAGE=381-Isht-Van rw root=/dev/sdc1
root=/dev/sdc1 showopts console=ttyS0,115200n8 console=tty0 elevator=cfq
pcie_aspm=force pcie_ports=native reboot=bios
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009ffff] usable
...
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000c2fffffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.6 present.
[ 0.000000] DMI: Dell Inc. PowerEdge T610/0CX0R0, BIOS 6.1.0 10/18/2011
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0xc30000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
...
[ 0.000000] EC000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask FF80000000 write-back
...
[ 0.000000] 7 base 0C00000000 mask FFC0000000 write-back
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new
0x7010600070106
[ 0.000000] e820: update [mem 0xd0000000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xcf379 max_arch_pfn = 0x400000000
[ 0.000000] initial memory mapped: [mem 0x00000000-0x1fffffff]
[ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: [mem 0x00000000-0xcf378fff]
[ 0.000000] [mem 0x00000000-0xbfffffff] page 1G
[ 0.000000] [mem 0xc0000000-0xcf1fffff] page 2M
[ 0.000000] [mem 0xcf200000-0xcf378fff] page 4k
[ 0.000000] kernel direct mapping tables up to 0xcf378fff @ [mem
0x1fffd000-0x1fffffff]
[ 0.000000] init_memory_mapping: [mem 0x100000000-0xc2fffffff]
[ 0.000000] [mem 0x100000000-0xbffffffff] page 1G
[ 0.000000] [mem 0xc00000000-0xc2fffffff] page 2M
[ 0.000000] kernel direct mapping tables up to 0xc2fffffff @ [mem
0xcf377000-0xcf378fff]
[ 0.000000] ACPI: RSDP 00000000000f1170 00024 (v02 DELL )
...
[ 0.000000] ACPI: TCPA 00000000cf3b3f34 00064 (v02 DELL PE_SC3
00000001 DELL 00000001)
[ 0.000000] ACPI: SSDT 00000000cf3b7000 037A4 (v01 INTEL PPM RCM
80000001 INTL 20061109)
[ 0.000000] ACPI: Local APIC address 0xfee00000
...
[ 0.000000] SRAT: PXM 2 -> APIC 0x14 -> Node 1
[ 0.000000] SRAT: Node 1 PXM 2 [mem 0x00000000-0xcfffffff]
[ 0.000000] SRAT: Node 1 PXM 2 [mem 0x100000000-0x62fffffff]
[ 0.000000] SRAT: Node 0 PXM 1 [mem 0x630000000-0xc2fffffff]
[ 0.000000] NUMA: Node 1 [mem 0x00000000-0xcfffffff] + [mem
0x100000000-0x62fffffff] -> [mem 0x00000000-0x62fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x630000000-0xc2fffffff]
[ 0.000000] NODE_DATA [mem 0xc2fffd000-0xc2fffffff]
[ 0.000000] Initmem setup node 1 [mem 0x00000000-0x62fffffff]
[ 0.000000] NODE_DATA [mem 0x62fffd000-0x62fffffff]
[ 0.000000] [ffffea0000000000-ffffea0018bfffff] PMD ->
[ffff880617e00000-ffff88062fdfffff] on node 1
[ 0.000000] [ffffea0018c00000-ffffea0030bfffff] PMD ->
[ffff880c17600000-ffff880c2f5fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0xc2fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 1: [mem 0x00001000-0x0009ffff]
[ 0.000000] node 1: [mem 0x00100000-0xcf378fff]
[ 0.000000] node 1: [mem 0x100000000-0x62fffffff]
[ 0.000000] node 0: [mem 0x630000000-0xc2fffffff]
[ 0.000000] On node 0 totalpages: 6291456
[ 0.000000] Normal zone: 98304 pages used for memmap
[ 0.000000] Normal zone: 6193152 pages, LIFO batch:31
[ 0.000000] On node 1 totalpages: 6288152
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 8 pages reserved
[ 0.000000] DMA zone: 3927 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 13198 pages used for memmap
[ 0.000000] DMA32 zone: 831467 pages, LIFO batch:31
[ 0.000000] Normal zone: 84992 pages used for memmap
[ 0.000000] Normal zone: 5354496 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
...
[ 0.000000] ACPI: LAPIC (acpi_id[0x20] lapic_id[0xff] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI
0-23
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec80000] gsi_base[32])
[ 0.000000] IOAPIC[1]: apic_id 1, version 32, address 0xfec80000, GSI
32-55
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
[ 0.000000] smpboot: 32 Processors exceeds NR_CPUS limit of 12
[ 0.000000] smpboot: Allowing 12 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 72
[ 0.000000] e820: [mem 0xd0000000-0xdfffffff] available for PCI devices
[ 0.000000] setup_percpu: NR_CPUS:12 nr_cpumask_bits:12 nr_cpu_ids:12
nr_node_ids:2
[ 0.000000] PERCPU: Embedded 476 pages/cpu @ffff880617200000 s1918016
r8192 d23488 u2097152
[ 0.000000] pcpu-alloc: s1918016 r8192 d23488 u2097152 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 00 [0] 02 [0] 04 [0] 06 [0] 08 [0] 10 [1]
01 [1] 03
[ 0.000000] pcpu-alloc: [1] 05 [1] 07 [1] 09 [1] 11
[ 0.000000] Built 2 zonelists in Zone order, mobility grouping on.
Total pages: 12383042
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: reboot=bios BOOT_IMAGE=381-Isht-Van
rw root=/dev/sdc1 root=/dev/sdc1 showopts console=ttyS0,115200n8
console=tty0 elevator=cfq pcie_aspm=force pcie_ports=native reboot=bios
[ 0.000000] PCIe ASPM is forcibly enabled
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Memory: 49417684k/51118080k available (6379k kernel code,
799648k absent, 900748k reserved, 6697k data, 2356k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0,
CPUs=12, Nodes=2
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:4352 nr_irqs:1320 16
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 132x43
[ 0.000000] console [tty0] enabled
[ 0.000000] console [ttyS0] enabled
...
[ 0.000000] Enabling automatic NUMA balancing. Configure with
numa_balancing= or sysctl
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.001000] tsc: Detected 2793.076 MHz processor
[ 0.000004] Calibrating delay loop (skipped), value calculated using
timer frequency.. 5586.15 BogoMIPS (lpj=2793076)
[ 0.010813] pid_max: default: 32768 minimum: 301
[ 0.015614] Security Framework initialized
[ 0.023350] Dentry cache hash table entries: 8388608 (order: 14,
67108864 bytes)
[ 0.044185] Inode-cache hash table entries: 4194304 (order: 13,
33554432 bytes)
[ 0.057474] Mount-cache hash table entries: 256
...
[ 0.089812] CPU: Physical Processor ID: 1
[ 0.093952] CPU: Processor Core ID: 0
[ 0.097757] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.097757] ENERGY_PERF_BIAS: View and update with
x86_energy_perf_policy(8)
[ 0.110967] mce: CPU supports 9 MCE banks
[ 0.115114] CPU0: Thermal monitoring enabled (TM1)
[ 0.120048] process: using mwait in idle threads
[ 0.124793] Last level iTLB entries: 4KB 512, 2MB 7, 4MB 7
[ 0.124793] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32
[ 0.124793] tlb_flushall_shift: 6
[ 0.139667] Freeing SMP alternatives: 20k freed
[ 0.144332] ACPI: Core revision 20121018
[ 0.152164] dmar: Host address width 40
[ 0.156136] dmar: DRHD base: 0x000000fed90000 flags: 0x1
[ 0.161569] dmar: IOMMU 0: reg_base_addr fed90000 ver 1:0 cap
c90780106f0462 ecap f020f6
...
[ 0.224974] dmar: RMRR base: 0x000000cf4c2000 end: 0x000000cf4c2fff
[ 0.231442] dmar: ATSR flags: 0x0
[ 0.235046] Switched APIC routing to physical flat.
[ 0.240639] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.256738] smpboot: CPU0: Intel(R) Xeon(R) CPU X5660 @
2.80GHz (fam: 06, model: 2c, stepping: 02)
[ 0.368291] Performance Events: PEBS fmt1+, 16-deep LBR, Westmere
events, Intel PMU driver.
[ 0.376959] perf_event_intel: CPUID marked event: 'bus cycles'
unavailable
[ 0.383937] ... version: 3
[ 0.388059] ... bit width: 48
[ 0.392282] ... generic registers: 4
[ 0.396395] ... value mask: 0000ffffffffffff
[ 0.401818] ... max period: 000000007fffffff
[ 0.407240] ... fixed-purpose events: 3
[ 0.411353] ... event mask: 000000070000000f
[ 0.424313] SMP alternatives: lockdep: fixing up alternatives
[ 0.526339] NMI watchdog: enabled on all CPUs, permanently consumes
one hw-PMU counter.
[ 0.430197] smpboot: Booting Node 1, Processors #1
...
[ 0.767737] smpboot: Booting Node 0, Processors #10
[ 0.787660] SMP alternatives: lockdep: fixing up alternatives
[ 0.793815] OK
[ 0.795696] smpboot: Booting Node 1, Processors #11 OK
[ 0.814480] Brought up 12 CPUs
[ 0.817643] smpboot: Total of 12 processors activated (67031.54 BogoMIPS)
[ 0.837389] devtmpfs: initialized
[ 0.841517] NET: Registered protocol family 16
[ 0.846297] i2c-core: driver [dummy] registered
[ 0.846445] ACPI FADT declares the system doesn't support PCIe ASPM,
so disable it
[ 0.854119] ACPI: bus type pci registered
[ 0.858333] dca service started, version 1.12.1
[ 0.863002] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem
0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.872412] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.915444] PCI: Using configuration type 1 for base access
[ 0.923541] bio: create slab <bio-0> at 0
[ 0.927876] ACPI: Added _OSI(Module Device)
[ 0.932207] ACPI: Added _OSI(Processor Device)
[ 0.936769] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.941613] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.949347] ACPI: EC: Look up EC in DSDT
[ 0.952568] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.962779] ACPI: Interpreter enabled
[ 0.966551] ACPI: (supports S0 S5)
[ 0.970176] ACPI: Using IOAPIC for interrupt routing
[ 0.982895] HEST: Table parsing has been initialized.
[ 0.988063] PCI: Using host bridge windows from ACPI; if necessary,
use "pci=nocrs" and report a bug
[ 0.997500] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 1.003792] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 1.004949] pci_root PNP0A08:00: Requesting ACPI _OSC control (0x15)
[ 1.011897] pci_root PNP0A08:00: ACPI _OSC control (0x15) granted
[ 1.018511] PCI host bridge to bus 0000:00
[ 1.022727] pci_bus 0000:00: root bus resource [bus 00-ff]
...
[ 1.054860] pci_bus 0000:00: root bus resource [mem
0xfed40000-0xfed44fff]
[ 1.065200] pci 0000:00:00.0: [8086:3406] type 00 class 0x060000
...
[ 1.066442] pci 0000:00:16.0: [8086:3430] type 00 class 0x088000
[ 1.066459] pci 0000:00:16.0: reg 10: [mem 0xdf0e0000-0xdf0e3fff 64bit]
...
[ 1.067245] pci 0000:00:16.7: [8086:342c] type 00 class 0x088000
[ 1.067261] pci 0000:00:16.7: reg 10: [mem 0xdf0fc000-0xdf0fffff 64bit]
[ 1.067362] pci 0000:00:1a.0: [8086:2937] type 00 class 0x0c0300
...
[ 1.144174] pci 0000:00:1e.0: bridge window [mem
0xd0000000-0xfdffffff] (subtractive decode)
[ 1.144176] pci 0000:00:1e.0: bridge window [mem
0xfed40000-0xfed44fff] (subtractive decode)
[ 1.144234] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
...
[ 1.201823] ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 14
15) *0, disabled.
[ 1.210634] ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 1.218252] SCSI subsystem initialized
[ 1.222118] ACPI: bus type scsi registered
[ 1.226390] libata version 3.00 loaded.
[ 1.226405] ACPI: bus type usb registered
[ 1.230546] usbcore: registered new interface driver usbfs
[ 1.236210] usbcore: registered new interface driver hub
[ 1.241673] usbcore: registered new device driver usb
[ 1.246856] pps_core: LinuxPPS API ver. 1 registered
[ 1.251935] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
Rodolfo Giometti <[email protected]>
[ 1.261180] PTP clock support registered
[ 1.265251] PCI: Using ACPI for IRQ routing
[ 1.276548] PCI: Discovered peer bus fe
[ 1.280502] PCI: root bus fe: using default resources
[ 1.280503] PCI: Probing PCI hardware (bus fe)
[ 1.280544] PCI host bridge to bus 0000:fe
[ 1.284756] pci_bus 0000:fe: root bus resource [io 0x0000-0xffff]
[ 1.291039] pci_bus 0000:fe: root bus resource [mem
0x00000000-0xffffffffff]
[ 1.298198] pci_bus 0000:fe: No busn resource found for root bus,
will use [bus fe-ff]
[ 1.306219] pci 0000:fe:00.0: [8086:2c70] type 00 class 0x060000
...
[ 1.307032] pci 0000:fe:06.3: [8086:2db3] type 00 class 0x060000
[ 1.307092] pci_bus 0000:fe: busn_res: [bus fe-ff] end is updated to fe
[ 1.307859] PCI: Discovered peer bus ff
[ 1.311814] PCI: root bus ff: using default resources
[ 1.311815] PCI: Probing PCI hardware (bus ff)
[ 1.311850] PCI host bridge to bus 0000:ff
[ 1.316053] pci_bus 0000:ff: root bus resource [io 0x0000-0xffff]
[ 1.322346] pci_bus 0000:ff: root bus resource [mem
0x00000000-0xffffffffff]
[ 1.329504] pci_bus 0000:ff: No busn resource found for root bus,
will use [bus ff-ff]
[ 1.337525] pci 0000:ff:00.0: [8086:2c70] type 00 class 0x060000
...
[ 1.338386] pci 0000:ff:06.3: [8086:2db3] type 00 class 0x060000
[ 1.338450] pci_bus 0000:ff: busn_res: [bus ff] end is updated to ff
[ 1.339197] PCI: pci_cache_line_size set to 64 bytes
[ 1.339469] e820: reserve RAM buffer [mem 0xcf379000-0xcfffffff]
[ 1.339687] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 1.345199] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[ 1.353153] Switching to clocksource hpet
[ 1.369117] FS-Cache: Loaded
[ 1.372138] pnp: PnP ACPI init
[ 1.375319] ACPI: bus type pnp registered
[ 1.379569] pnp 00:00: [dma 4]
...
[ 1.455138] pnp 00:0a: Plug and Play ACPI device, IDs PNP0103 (active)
[ 1.455269] system 00:0b: [mem 0xfed90000-0xfed91fff] could not be
reserved
[ 1.462353] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.462732] pnp: PnP ACPI: found 12 devices
[ 1.467044] ACPI: ACPI bus type pnp unregistered
[ 1.481774] pci 0000:06:00.1: address space collision: [mem
0xdf300000-0xdf37ffff pref] conflicts with 0000:06:00.0 [mem
0xdf300000-0xdf37ffff pref]
[ 1.495395] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 1.500484] pci 0000:00:01.0: bridge window [mem 0xda000000-0xddffffff]
...
[ 1.611994] pci 0000:00:1e.0: bridge window [mem 0xde000000-0xdeffffff]
[ 1.623952] pci 0000:00:1e.0: bridge window [mem
0xd9000000-0xd97fffff 64bit pref]
[ 1.631898] pci 0000:00:1e.0: setting latency timer to 64
...
[ 1.631951] pci_bus 0000:ff: resource 5 [mem 0x00000000-0xffffffffff]
[ 1.632012] NET: Registered protocol family 2
[ 1.637148] TCP established hash table entries: 524288 (order: 11,
8388608 bytes)
[ 1.646389] TCP bind hash table entries: 65536 (order: 10, 5242880 bytes)
...
[ 1.815851] IOMMU: Setting identity map for device 0000:00:1a.7
[0xcf4c8000 - 0xcf4dffff]
[ 1.824137] IOMMU: Setting identity map for device 0000:00:1d.7
[0xcf4c8000 - 0xcf4dffff]
[ 1.832424] IOMMU: Prepare 0-16MiB unity mapping for LPC
[ 1.837883] IOMMU: Setting identity map for device 0000:00:1f.0 [0x0
- 0xffffff]
[ 1.845592] PCI-DMA: Intel(R) Virtualization Technology for Directed I/O
...
[ 1.923963] microcode: CPU11 sig=0x206c2, pf=0x1, revision=0x15
[ 1.930096] microcode: Microcode Update Driver: v2.00
<[email protected]>, Peter Oruba
[ 1.939117] sha1_ssse3: Using SSSE3 optimized SHA-1 implementation
[ 1.939131] cryptomgr_test (77) used greatest stack depth: 5832 bytes
left
[ 1.954626] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.965735] Key type cifs.idmap registered
[ 1.970070] SGI XFS with ACLs, security attributes, realtime, large
block/inode numbers, no debug enabled
[ 1.980271] msgmni has been set to 32768
[ 1.985133] cryptomgr_test (97) used greatest stack depth: 5776 bytes
left
[ 1.985471] alg: No test for stdrng (krng)
[ 1.985539] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 250)
[ 1.985596] io scheduler noop registered
[ 1.985643] io scheduler cfq registered (default)
...
[ 1.987902] pcieport 0000:00:0a.0: irq 79 for MSI/MSI-X
[ 1.988057] pcieport 0000:00:01.0: Signaling PME through PCIe PME
interrupt
...
[ 1.988274] pcie_pme 0000:00:0a.0:pcie01: service driver pcie_pme loaded
[ 1.988375] intel_idle: MWAIT substates: 0x1120
[ 1.988375] intel_idle: v0.4 model 0x2C
[ 1.988376] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 2.115394] cryptomgr_test (99) used greatest stack depth: 5208 bytes
left
[ 2.122414] ipmi message handler version 39.2
[ 2.126909] ipmi device interface
[ 2.130384] IPMI System Interface driver.
[ 2.134590] ipmi_si: probing via SMBIOS
[ 2.138537] ipmi_si: SMBIOS: io 0xca8 regsize 1 spacing 4 irq 0
[ 2.144571] ipmi_si: Adding SMBIOS-specified kcs state machine
[ 2.150581] ipmi_si: Trying SMBIOS-specified kcs state machine at i/o
address 0xca8, slave address 0x20, irq 0
[ 2.376680] ipmi_si ipmi_si.0: Found new BMC (man_id: 0x0002a2,
prod_id: 0x0100, dev_id: 0x20)
[ 2.385509] ipmi_si ipmi_si.0: IPMI kcs interface initialized
[ 2.391506] ERST: Error Record Serialization Table (ERST) support is
initialized.
[ 2.399478] GHES: APEI firmware first mode is enabled by APEI bit and
WHEA _OSC.
[ 2.406995] ioatdma: Intel(R) QuickData Technology Driver 4.00
...
[ 2.416327] ioatdma 0000:00:16.7: irq 87 for MSI/MSI-X
[ 2.450434] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 2.480844] 00:04: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.507130] 00:05: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 2.513742] Non-volatile memory driver v1.3
[ 2.521604] brd: module loaded
[ 2.526285] loop: module loaded
[ 2.530376] nbd: registered device at major 43
[ 2.537559] gpio_ich: GPIO from 195 to 255 on gpio_ich
[ 2.543005] Loading iSCSI transport class v2.0-870.
[ 2.548103] megasas: 06.504.01.00-rc1 Mon. Oct. 1 17:00:00 PDT 2012
[ 2.554547] megasas: 0x1000:0x0079:0x1000:0x9275: bus 5:slot 0:func 0
[ 2.561326] megasas: FW now in Ready state
...
[ 2.844408] scsi 0:0:29:0: Direct-Access ATA Hitachi
HUA72202 A3EA PQ: 0 ANSI: 5
...
[ 2.958508] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April
27, 2011)
[ 2.959107] bnx2: Broadcom NetXtreme II Gigabit Ethernet Driver bnx2
v2.2.3 (June 27, 2012)
[ 2.959422] scsi 1:0:4:0: Direct-Access ATA Hitachi HUA72202
A3EA PQ: 0 ANSI: 5
[ 2.959720] bnx2 0000:01:00.0 eth0: Broadcom NetXtreme II BCM5709
1000Base-T (C0) PCI Express found at mem da000000, IRQ 36, node addr
00:26:b9:2c:a4:ef
[ 2.960305] bnx2 0000:01:00.1 eth1: Broadcom NetXtreme II BCM5709
1000Base-T (C0) PCI Express found at mem dc000000, IRQ 48, node addr
00:26:b9:2c:a4:f1
[ 2.960347] e1000e: Intel(R) PRO/1000 Network Driver - 2.1.4-k
[ 2.960348] e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
[ 2.960377] e1000e 0000:03:00.0: Disabling ASPM L1
[ 2.960470] e1000e 0000:03:00.0: Interrupt Throttling Rate (ints/sec)
set to dynamic conservative mode
[ 2.960511] e1000e 0000:03:00.0: irq 89 for MSI/MSI-X
[ 3.007831] scsi 1:0:5:0: Direct-Access ATA Hitachi HUA72202
A3EA PQ: 0 ANSI: 5
...
[ 3.127317] scsi 0:0:39:0: Direct-Access ATA Hitachi
HUA72202 A3EA PQ: 0 ANSI: 5
[ 3.132612] e1000e 0000:03:00.0 eth2: (PCI Express:2.5GT/s:Width x4)
00:15:17:bf:be:b2
[ 3.132614] e1000e 0000:03:00.0 eth2: Intel(R) PRO/1000 Network
Connection
[ 3.132689] e1000e 0000:03:00.0 eth2: MAC: 0, PHY: 4, PBA No: C57721-005
[ 3.132702] e1000e 0000:03:00.1: Disabling ASPM L1
[ 3.132795] e1000e 0000:03:00.1: Interrupt Throttling Rate (ints/sec)
set to dynamic conservative mode
[ 3.132836] e1000e 0000:03:00.1: irq 90 for MSI/MSI-X
[ 3.159261] Uhhuh. NMI received for unknown reason 31 on CPU 0.
[ 3.159261] Do you have a strange power saving mode enabled?
[ 3.159262] Dazed and confused, but trying to continue
[ 3.188918] dmar: DRHD: handling fault status reg 2
[ 3.193907] dmar: DMAR:[DMA Read] Request device [02:00.0] fault addr
ffe76000
[ 3.193907] DMAR:[fault reason 06] PTE Read access is not set
[ 3.240182] scsi 0:2:0:0: Direct-Access LSI MR9280DE-8e
2.0. PQ: 0 ANSI: 5
[ 3.248746] scsi 0:2:1:0: Direct-Access LSI MR9280DE-8e
2.0. PQ: 0 ANSI: 5
[ 3.282652] dmar: DRHD: handling fault status reg 102
[ 3.284312] ses 0:0:14:0: Attached Enclosure device
[ 3.284426] ses 0:0:14:0: Attached scsi generic sg0 type 13
[ 3.301981] dmar: DMAR:[DMA Read] Request device [02:00.0] fault addr
ffe8a000
[ 3.301981] DMAR:[fault reason 06] PTE Read access is not set
[ 3.305305] e1000e 0000:03:00.1 eth3: (PCI Express:2.5GT/s:Width x4)
00:15:17:bf:be:b3
[ 3.305307] e1000e 0000:03:00.1 eth3: Intel(R) PRO/1000 Network
Connection
[ 3.305382] e1000e 0000:03:00.1 eth3: MAC: 0, PHY: 4, PBA No: C57721-005
[ 3.305431] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver -
version 3.11.33-k
[ 3.305431] ixgbe: Copyright (c) 1999-2012 Intel Corporation.
[ 3.350903] scsi 1:0:32:0: Enclosure DP
BACKPLANE 1.07 PQ: 0 ANSI: 5
[ 3.359344] dmar: DRHD: handling fault status reg 202
[ 3.364534] dmar: DMAR:[DMA Read] Request device [02:00.0] fault addr
ffe89000
[ 3.364534] DMAR:[fault reason 06] PTE Read access is not set
[ 3.386416] ses 0:0:27:0: Attached Enclosure device
...
[ 3.508700] sd 0:2:1:0: [sdb] Attached SCSI disk
[ 3.622261] ses 1:0:32:0: Attached Enclosure device
[ 3.627372] ses 1:0:32:0: Attached scsi generic sg4 type 13
[ 3.733753] ixgbe 0000:06:00.0: irq 91 for MSI/MSI-X
[ 3.733763] ixgbe 0000:06:00.0: irq 92 for MSI/MSI-X
[ 3.733772] ixgbe 0000:06:00.0: irq 93 for MSI/MSI-X
[ 3.733780] ixgbe 0000:06:00.0: irq 94 for MSI/MSI-X
[ 3.733789] ixgbe 0000:06:00.0: irq 95 for MSI/MSI-X
[ 3.733797] ixgbe 0000:06:00.0: irq 96 for MSI/MSI-X
[ 3.733805] ixgbe 0000:06:00.0: irq 97 for MSI/MSI-X
[ 3.733814] ixgbe 0000:06:00.0: irq 98 for MSI/MSI-X
[ 3.733822] ixgbe 0000:06:00.0: irq 99 for MSI/MSI-X
[ 3.733831] ixgbe 0000:06:00.0: irq 100 for MSI/MSI-X
[ 3.733839] ixgbe 0000:06:00.0: irq 101 for MSI/MSI-X
[ 3.733847] ixgbe 0000:06:00.0: irq 102 for MSI/MSI-X
[ 3.733856] ixgbe 0000:06:00.0: irq 103 for MSI/MSI-X
[ 3.733933] ixgbe 0000:06:00.0: Multiqueue Enabled: Rx Queue count =
12, Tx Queue count = 12
[ 3.742464] dmar: DRHD: handling fault status reg 302
[ 3.742467] dmar: DMAR:[DMA Read] Request device [02:00.0] fault addr
ffe86000
[ 3.742467] DMAR:[fault reason 06] PTE Read access is not set
[ 3.805353] dmar: DRHD: handling fault status reg 402
[ 3.810529] dmar: DMAR:[DMA Read] Request device [02:00.0] fault addr
ffe87000
[ 3.810529] DMAR:[fault reason 06] PTE Read access is not set
[ 3.820908] ixgbe 0000:06:00.0: (PCI Express:5.0GT/s:Width x8)
a0:36:9f:15:c9:c0
[ 3.889229] dmar: DRHD: handling fault status reg 502
[ 3.894389] dmar: DMAR:[DMA Read] Request device [02:00.0] fault addr
ffe84000
[ 3.894389] DMAR:[fault reason 06] PTE Read access is not set
...
[ 4.037793] sd 1:2:0:0: [sdc] Attached SCSI disk
[ 4.062063] dmar: DRHD: handling fault status reg 702
[ 4.067233] dmar: DMAR:[DMA Read] Request device [02:00.0] fault addr
ffe7f000
[ 4.067233] DMAR:[fault reason 06] PTE Read access is not set
[ 4.100647] sdd: sdd1
[ 4.103655] sd 1:2:1:0: [sdd] Attached SCSI disk
[ 4.123872] ixgbe 0000:06:00.0: Intel(R) 10 Gigabit Network Connection
[ 4.558317] ixgbe 0000:06:00.1: irq 104 for MSI/MSI-X
[ 4.558326] ixgbe 0000:06:00.1: irq 105 for MSI/MSI-X
[ 4.558335] ixgbe 0000:06:00.1: irq 106 for MSI/MSI-X
[ 4.558343] ixgbe 0000:06:00.1: irq 107 for MSI/MSI-X
[ 4.558351] ixgbe 0000:06:00.1: irq 108 for MSI/MSI-X
[ 4.558360] ixgbe 0000:06:00.1: irq 109 for MSI/MSI-X
[ 4.558368] ixgbe 0000:06:00.1: irq 110 for MSI/MSI-X
[ 4.558376] ixgbe 0000:06:00.1: irq 111 for MSI/MSI-X
[ 4.558385] ixgbe 0000:06:00.1: irq 112 for MSI/MSI-X
[ 4.558393] ixgbe 0000:06:00.1: irq 113 for MSI/MSI-X
[ 4.558401] ixgbe 0000:06:00.1: irq 114 for MSI/MSI-X
[ 4.558410] ixgbe 0000:06:00.1: irq 115 for MSI/MSI-X
[ 4.558418] ixgbe 0000:06:00.1: irq 116 for MSI/MSI-X
[ 4.558490] ixgbe 0000:06:00.1: Multiqueue Enabled: Rx Queue count =
12, Tx Queue count = 12
[ 4.627063] ixgbe 0000:06:00.1: (PCI Express:5.0GT/s:Width x8)
a0:36:9f:15:c9:c2
[ 4.794640] ixgbe 0000:06:00.1: MAC: 3, PHY: 3, PBA No: G45270-002
[ 4.943908] ixgbe 0000:06:00.1: Intel(R) 10 Gigabit Network Connection
[ 4.950603] I2O subsystem v1.325
[ 4.953953] i2o: max drivers = 8
...
[ 5.519890] usbserial: USB Serial support registered for generic
[ 5.526107] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 5.535870] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 5.541055] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 5.549583] usbcore: registered new interface driver wacom
[ 5.555277] input: PC Speaker as /devices/platform/pcspkr/input/input0
[ 5.562198] rtc_cmos 00:03: RTC can wake from S4
[ 5.567265] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 5.574040] rtc0: alarms up to one day, y3k, 242 bytes nvram, hpet irqs
[ 5.580796] i2c /dev entries driver
[ 5.585128] ACPI Error: No handler for Region [IPMI]
(ffff880613c39240) [IPMI] (20121018/evregion-376)
[ 5.594665] ACPI Error: Region IPMI (ID=7) has no handler
(20121018/exfldio-305)
[ 5.602573] ACPI Error: Method parse/execution failed
[\_SB_.PMI0._GHL] (Node ffff880613c38b18), AE_NOT_EXIST
(20121018/psparse-537)
[ 5.614909] ACPI Error: Method parse/execution failed
[\_SB_.PMI0._PMC] (Node ffff880613c38a78), AE_NOT_EXIST
(20121018/psparse-537)
[ 5.627254] ACPI Exception: AE_NOT_EXIST, Evaluating _PMC
(20121018/power_meter-753)
[ 5.635332] coretemp coretemp.1: TjMax is 96 degrees C
...
[ 5.635573] coretemp coretemp.0: TjMax is 96 degrees C
[ 5.635834] device-mapper: uevent: version 1.0.3
[ 5.640724] device-mapper: ioctl: 4.23.1-ioctl (2012-12-18)
initialised: [email protected]
[ 5.649319] EDAC MC: Ver: 3.0.0
[ 5.653653] EDAC MC1: Giving out device to 'i7core_edac.c' 'i7 core
#1': DEV 0000:fe:03.0
[ 5.662012] EDAC PCI0: Giving out device to module 'i7core_edac'
controller 'EDAC PCI controller': DEV '0000:fe:03.0' (POLLED)
[ 5.674123] EDAC MC0: Giving out device to 'i7core_edac.c' 'i7 core
#0': DEV 0000:ff:03.0
[ 5.682450] EDAC PCI1: Giving out device to module 'i7core_edac'
controller 'EDAC PCI controller': DEV '0000:ff:03.0' (POLLED)
[ 5.694321] EDAC i7core: Driver loaded, 2 memory controller(s) found.
[ 5.701319] cpuidle: using governor ladder
[ 5.706287] cpuidle: using governor menu
[ 5.711285] EFI Variables Facility v0.08 2004-May-17
[ 5.716452] dcdbas dcdbas: Dell Systems Management Base Driver
(version 5.6.0-3.2)
[ 5.724250] usbcore: registered new interface driver usbhid
[ 5.729946] usbhid: USB HID core driver
[ 5.733841] usb 7-1: new low-speed USB device number 2 using uhci_hcd
[ 5.740464] GACT probability on
[ 5.743781] Netfilter messages via NETLINK v0.30.
[ 5.748733] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 5.754795] TCP: highspeed registered
[ 5.758606] TCP: htcp registered
[ 5.761957] TCP: scalable registered
[ 5.765638] TCP: lp registered
[ 5.768828] NET: Registered protocol family 17
[ 5.773416] Key type dns_resolver registered
[ 5.778771] registered taskstats version 1
[ 5.785472] console [netcon0] enabled
[ 5.789268] netconsole: network logging started
[ 5.794417] rtc_cmos 00:03: setting system clock to 2013-03-03
13:36:33 UTC (1362317793)
...
[ 6.034685] Freeing unused kernel memory: 2356k freed
[ 6.040393] Write protecting the kernel read-only data: 12288k
[ 6.055099] Freeing unused kernel memory: 1804k freed
[ 6.066535] Freeing unused kernel memory: 1296k freed
...
[ 7.272433] XFS (sdc6): Ending clean mount
[ 8.729858] ACPI: Requesting acpi_cpufreq
[ 8.736906] mousedev: PS/2 mouse device common for all mice
[ 8.740862] Uhhuh. NMI received for unknown reason 31 on CPU 0.
[ 8.740862] Do you have a strange power saving mode enabled?
[ 8.740863] Dazed and confused, but trying to continue
[ 8.763852] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
[ 8.771464] ACPI: Power Button [PWRF]
[ 8.816722] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 8.822886] iTCO_wdt: Found a ICH9 TCO device (Version=2, TCOBASE=0x0860)
[ 8.830275] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 8.871909] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work
properly. Using workaround
[ 9.311531] Adding 8393924k swap on /dev/sdc5. Priority:-1 extents:1
across:8393924k
[ 9.898467] bio: create slab <bio-1> at 1
[ 10.320156] bio: create slab <bio-2> at 2
[ 12.848010] XFS (sdc2): Mounting Filesystem
...
[ 14.534075] XFS (dm-6): Ending clean mount
[ 18.538494] bonding: bond0: Setting MII monitoring interval to 250.
[ 18.552402] bonding: bond0: Adding slave eth_s2_0.
[ 18.620810] pps pps0: new PPS source ptp0
[ 18.624829] ixgbe 0000:06:00.0: registered PHC device on eth_s2_0
[ 19.055454] bonding: bond0: enslaving eth_s2_0 as an active interface
with a down link.
[ 19.073574] bonding: bond0: Adding slave eth_s2_1.
[ 19.140326] pps pps1: new PPS source ptp1
[ 19.144340] ixgbe 0000:06:00.1: registered PHC device on eth_s2_1
[ 19.574896] bonding: bond0: enslaving eth_s2_1 as an active interface
with a down link.
[ 19.597337] ixgbe 0000:06:00.0 eth_s2_0: changing MTU from 1500 to 9000
[ 20.466899] ixgbe 0000:06:00.1 eth_s2_1: changing MTU from 1500 to 9000
[ 22.177843] e1000e 0000:03:00.0 eth0: changing MTU from 1500 to 9000
[ 22.472021] e1000e 0000:03:00.0: irq 89 for MSI/MSI-X
[ 22.572957] e1000e 0000:03:00.0: irq 89 for MSI/MSI-X
[ 22.917065] e1000e 0000:03:00.1 eth1: changing MTU from 1500 to 9000
[ 23.211319] e1000e 0000:03:00.1: irq 90 for MSI/MSI-X
[ 23.311726] e1000e 0000:03:00.1: irq 90 for MSI/MSI-X
[ 23.677061] bnx2 0000:01:00.0: irq 117 for MSI/MSI-X
...
[ 23.677168] bnx2 0000:01:00.0: irq 125 for MSI/MSI-X
[ 23.729930] bnx2 0000:01:00.0 eth2: using MSIX
[ 23.730055] ip (2400) used greatest stack depth: 2096 bytes left
[ 24.075847] bnx2 0000:01:00.1: irq 126 for MSI/MSI-X
...
[ 24.075913] bnx2 0000:01:00.1: irq 134 for MSI/MSI-X
[ 24.129293] bnx2 0000:01:00.1 eth3: using MSIX
[ 24.776033] ixgbe 0000:06:00.0 eth_s2_0: NIC Link is Up 10 Gbps, Flow
Control: RX/TX
[ 24.820010] BUG: scheduling while atomic: kworker/u:2/109/0x00000002
[ 24.826415] 4 locks held by kworker/u:2/109:
[ 24.826425] #0: ((bond_dev->name)){......}, at:
[<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
[ 24.826428] #1: ((&(&bond->mii_work)->work)){......}, at:
[<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
[ 24.826435] #2: (rtnl_mutex){......}, at: [<ffffffff81590c00>]
rtnl_trylock+0x10/0x20
[ 24.826441] #3: (&bond->lock){......}, at: [<ffffffff8145af55>]
bond_mii_monitor+0x2d5/0x630
[ 24.826448] Modules linked in: iptable_filter kvm_intel kvm iTCO_wdt
acpi_cpufreq mperf button mousedev processor
[ 24.826451] Pid: 109, comm: kworker/u:2 Not tainted 3.8.1-Isht-Van #6
[ 24.826452] Call Trace:
[ 24.826459] [<ffffffff8162b039>] __schedule_bug+0x5e/0x6c
[ 24.826475] [<ffffffff816345a2>] __schedule+0x762/0x7f0
[ 24.826479] [<ffffffff81634744>] schedule+0x24/0x70
[ 24.826488] [<ffffffff81633704>]
schedule_hrtimeout_range_clock+0xa4/0x130
[ 24.826495] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
[ 24.826499] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
[ 24.826507] [<ffffffff8163379e>] schedule_hrtimeout_range+0xe/0x10
[ 24.826512] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
[ 24.826518] [<ffffffff814b2d8c>] ixgbe_acquire_swfw_sync_X540+0xbc/0x100
[ 24.826527] [<ffffffff814aeb1d>] ixgbe_read_phy_reg_generic+0x3d/0x140
[ 24.826532] [<ffffffff814aedbc>]
ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
[ 24.826537] [<ffffffff8145af55>] ? bond_mii_monitor+0x2d5/0x630
[ 24.826543] [<ffffffff814a64f4>] ixgbe_get_settings+0x34/0x340
[ 24.826546] [<ffffffff81586ac8>] __ethtool_get_settings+0x88/0x130
[ 24.826552] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
[ 24.826554] [<ffffffff8145afc4>] bond_mii_monitor+0x344/0x630
[ 24.826556] [<ffffffff8105dab1>] process_one_work+0x1a1/0x5d0
[ 24.826558] [<ffffffff8105da4d>] ? process_one_work+0x13d/0x5d0
[ 24.826560] [<ffffffff8145ac80>] ? bond_loadbalance_arp_mon+0x300/0x300
[ 24.826563] [<ffffffff8105ed60>] worker_thread+0x160/0x3f0
[ 24.826565] [<ffffffff8105ec00>] ? manage_workers+0x290/0x290
[ 24.826569] [<ffffffff81064446>] kthread+0xd6/0xe0
[ 24.826573] [<ffffffff8107004a>] ? finish_task_switch+0x3a/0x100
[ 24.826576] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
[ 24.826578] [<ffffffff81636fec>] ret_from_fork+0x7c/0xb0
[ 24.826580] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
[ 24.829930] BUG: scheduling while atomic: kworker/u:2/109/0x00000002
[ 24.836284] 4 locks held by kworker/u:2/109:
[ 24.836287] #0: ((bond_dev->name)){......}, at:
[<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
[ 24.836297] #1: ((&(&bond->mii_work)->work)){......}, at:
[<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
[ 24.836304] #2: (rtnl_mutex){......}, at: [<ffffffff81590c00>]
rtnl_trylock+0x10/0x20
[ 24.836312] #3: (&bond->lock){......}, at: [<ffffffff8145af55>]
bond_mii_monitor+0x2d5/0x630
[ 24.836320] Modules linked in: iptable_filter kvm_intel kvm iTCO_wdt
acpi_cpufreq mperf button mousedev processor
[ 24.836334] Pid: 109, comm: kworker/u:2 Tainted: G W
3.8.1-Isht-Van #6
[ 24.836336] Call Trace:
[ 24.836342] [<ffffffff8162b039>] __schedule_bug+0x5e/0x6c
[ 24.836348] [<ffffffff816345a2>] __schedule+0x762/0x7f0
[ 24.836352] [<ffffffff81634744>] schedule+0x24/0x70
[ 24.836357] [<ffffffff81633704>]
schedule_hrtimeout_range_clock+0xa4/0x130
[ 24.836362] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
[ 24.836366] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
[ 24.836371] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
[ 24.836375] [<ffffffff8163379e>] schedule_hrtimeout_range+0xe/0x10
[ 24.836380] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
[ 24.836385] [<ffffffff814b2cbe>] ixgbe_release_swfw_sync_X540+0x4e/0x60
[ 24.836390] [<ffffffff814aebed>] ixgbe_read_phy_reg_generic+0x10d/0x140
[ 24.836395] [<ffffffff814aedbc>]
ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
[ 24.836400] [<ffffffff8145af55>] ? bond_mii_monitor+0x2d5/0x630
[ 24.836404] [<ffffffff814a64f4>] ixgbe_get_settings+0x34/0x340
[ 24.836409] [<ffffffff81586ac8>] __ethtool_get_settings+0x88/0x130
[ 24.836413] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
[ 24.836418] [<ffffffff8145afc4>] bond_mii_monitor+0x344/0x630
[ 24.836422] [<ffffffff8105dab1>] process_one_work+0x1a1/0x5d0
[ 24.836426] [<ffffffff8105da4d>] ? process_one_work+0x13d/0x5d0
[ 24.836431] [<ffffffff8145ac80>] ? bond_loadbalance_arp_mon+0x300/0x300
[ 24.836436] [<ffffffff8105ed60>] worker_thread+0x160/0x3f0
[ 24.836440] [<ffffffff8105ec00>] ? manage_workers+0x290/0x290
[ 24.836445] [<ffffffff81064446>] kthread+0xd6/0xe0
[ 24.836449] [<ffffffff8107004a>] ? finish_task_switch+0x3a/0x100
[ 24.836455] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
[ 24.836459] [<ffffffff81636fec>] ret_from_fork+0x7c/0xb0
[ 24.836464] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
[ 24.839952] bonding: bond0: link status definitely up for interface
eth_s2_0, 10000 Mbps full duplex.
[ 24.839968] bonding: bond0: first active interface up!
[ 24.955598] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow
Control: Rx/Tx
[ 25.621770] ixgbe 0000:06:00.1 eth_s2_1: NIC Link is Up 10 Gbps, Flow
Control: RX/TX
[ 25.838277] BUG: scheduling while atomic: kworker/u:2/109/0x00000002
[ 25.844673] 4 locks held by kworker/u:2/109:
[ 25.844676] #0: ((bond_dev->name)){......}, at:
[<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
[ 25.844689] #1: ((&(&bond->mii_work)->work)){......}, at:
[<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
[ 25.844705] #2: (rtnl_mutex){......}, at: [<ffffffff81590c00>]
rtnl_trylock+0x10/0x20
[ 25.844715] #3: (&bond->lock){......}, at: [<ffffffff8145af55>]
bond_mii_monitor+0x2d5/0x630
[ 25.844724] Modules linked in: iptable_filter kvm_intel kvm iTCO_wdt
acpi_cpufreq mperf button mousedev processor
[ 25.844740] Pid: 109, comm: kworker/u:2 Tainted: G W
3.8.1-Isht-Van #6
[ 25.844743] Call Trace:
[ 25.844752] [<ffffffff8162b039>] __schedule_bug+0x5e/0x6c
[ 25.844759] [<ffffffff816345a2>] __schedule+0x762/0x7f0
[ 25.844764] [<ffffffff81634744>] schedule+0x24/0x70
[ 25.844770] [<ffffffff81633704>]
schedule_hrtimeout_range_clock+0xa4/0x130
[ 25.844776] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
[ 25.844781] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
[ 25.844786] [<ffffffff8163379e>] schedule_hrtimeout_range+0xe/0x10
[ 25.844791] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
[ 25.844798] [<ffffffff814b2d8c>] ixgbe_acquire_swfw_sync_X540+0xbc/0x100
[ 25.844805] [<ffffffff814aeb1d>] ixgbe_read_phy_reg_generic+0x3d/0x140
[ 25.844811] [<ffffffff814aedbc>]
ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
[ 25.844818] [<ffffffff8145af55>] ? bond_mii_monitor+0x2d5/0x630
[ 25.844832] [<ffffffff814a64f4>] ixgbe_get_settings+0x34/0x340
[ 25.844845] [<ffffffff81586ac8>] __ethtool_get_settings+0x88/0x130
[ 25.844858] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
[ 25.844866] [<ffffffff8145afc4>] bond_mii_monitor+0x344/0x630
[ 25.844871] [<ffffffff8105dab1>] process_one_work+0x1a1/0x5d0
[ 25.844875] [<ffffffff8105da4d>] ? process_one_work+0x13d/0x5d0
[ 25.844880] [<ffffffff8145ac80>] ? bond_loadbalance_arp_mon+0x300/0x300
[ 25.844885] [<ffffffff8105ed60>] worker_thread+0x160/0x3f0
[ 25.844890] [<ffffffff8105ec00>] ? manage_workers+0x290/0x290
[ 25.844896] [<ffffffff81064446>] kthread+0xd6/0xe0
[ 25.844901] [<ffffffff8107004a>] ? finish_task_switch+0x3a/0x100
[ 25.844907] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
[ 25.844911] [<ffffffff81636fec>] ret_from_fork+0x7c/0xb0
[ 25.844916] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
[ 25.848369] BUG: scheduling while atomic: kworker/u:2/109/0x00000002
[ 25.854761] 4 locks held by kworker/u:2/109:
[ 25.854764] #0: ((bond_dev->name)){......}, at:
[<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
[ 25.854774] #1: ((&(&bond->mii_work)->work)){......}, at:
[<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
[ 25.854781] #2: (rtnl_mutex){......}, at: [<ffffffff81590c00>]
rtnl_trylock+0x10/0x20
[ 25.854790] #3: (&bond->lock){......}, at: [<ffffffff8145af55>]
bond_mii_monitor+0x2d5/0x630
[ 25.854798] Modules linked in: iptable_filter kvm_intel kvm iTCO_wdt
acpi_cpufreq mperf button mousedev processor
[ 25.854812] Pid: 109, comm: kworker/u:2 Tainted: G W
3.8.1-Isht-Van #6
[ 25.854814] Call Trace:
[ 25.854820] [<ffffffff8162b039>] __schedule_bug+0x5e/0x6c
[ 25.854826] [<ffffffff816345a2>] __schedule+0x762/0x7f0
[ 25.854831] [<ffffffff81634744>] schedule+0x24/0x70
[ 25.854835] [<ffffffff81633704>]
schedule_hrtimeout_range_clock+0xa4/0x130
[ 25.854840] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
[ 25.854844] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
[ 25.854849] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
[ 25.854854] [<ffffffff8163379e>] schedule_hrtimeout_range+0xe/0x10
[ 25.854858] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
[ 25.854863] [<ffffffff814b2cbe>] ixgbe_release_swfw_sync_X540+0x4e/0x60
[ 25.854869] [<ffffffff814aebed>] ixgbe_read_phy_reg_generic+0x10d/0x140
[ 25.854874] [<ffffffff814aedbc>]
ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
[ 25.854879] [<ffffffff8145af55>] ? bond_mii_monitor+0x2d5/0x630
[ 25.854883] [<ffffffff814a64f4>] ixgbe_get_settings+0x34/0x340
[ 25.854888] [<ffffffff81586ac8>] __ethtool_get_settings+0x88/0x130
[ 25.854892] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
[ 25.854897] [<ffffffff8145afc4>] bond_mii_monitor+0x344/0x630
[ 25.854901] [<ffffffff8105dab1>] process_one_work+0x1a1/0x5d0
[ 25.854905] [<ffffffff8105da4d>] ? process_one_work+0x13d/0x5d0
[ 25.854910] [<ffffffff8145ac80>] ? bond_loadbalance_arp_mon+0x300/0x300
[ 25.854915] [<ffffffff8105ed60>] worker_thread+0x160/0x3f0
[ 25.854920] [<ffffffff8105ec00>] ? manage_workers+0x290/0x290
[ 25.854925] [<ffffffff81064446>] kthread+0xd6/0xe0
[ 25.854929] [<ffffffff8107004a>] ? finish_task_switch+0x3a/0x100
[ 25.854935] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
[ 25.854939] [<ffffffff81636fec>] ret_from_fork+0x7c/0xb0
[ 25.854944] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
[ 25.858392] bonding: bond0: link status definitely up for interface
eth_s2_1, 10000 Mbps full duplex.
[ 27.292402] bnx2 0000:01:00.1 eth3: NIC Copper Link is Up, 1000 Mbps
full duplex
[ 27.292406] , receive & transmit flow control ON
[ 28.682172] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow
Control: Rx/Tx
[ 29.037441] Status code returned 0xc000005e NT_STATUS_NO_LOGON_SERVERS
[ 29.037451] CIFS VFS: Send error in SessSetup = -5
[ 29.043058] CIFS VFS: cifs_mount failed w/return code = -5
[ 30.005962] Status code returned 0xc000005e NT_STATUS_NO_LOGON_SERVERS
[ 30.005971] CIFS VFS: Send error in SessSetup = -5
[ 30.011333] CIFS VFS: cifs_mount failed w/return code = -5
[ 31.093294] Status code returned 0xc000000d NT_STATUS_INVALID_PARAMETER
[ 31.093303] CIFS VFS: Send error in SessSetup = -22
[ 31.098672] CIFS VFS: cifs_mount failed w/return code = -22
[ 32.339022] device eth0 entered promiscuous mode
[ 32.523684] device eth1 entered promiscuous mode
[ 32.739312] device eth2 entered promiscuous mode
[ 32.922051] device eth3 entered promiscuous mode
[ 33.075705] device bond0 entered promiscuous mode
[ 33.075711] device eth_s2_0 entered promiscuous mode
[ 33.076022] device eth_s2_1 entered promiscuous mode
[ 34.783087] u32 classifier
[ 34.783089] Performance counters on
[ 34.783090] input device check on
[ 34.783091] Actions configured
[ 40.834154] bnx2 0000:01:00.0 eth2: NIC Copper Link is Up, 100 Mbps
full duplex
[ 40.834158] , receive & transmit flow control ON
On 03/07/2013 03:05 PM, Linda Walsh wrote:
>
>
>
>
> Michael Wang wrote:
>> On 03/02/2013 01:21 PM, Linda Walsh wrote:
>> Update -- it *used* to stop the messages in 3.6.7.
>>
>> It no longer stops the messages in 3.8.1 -- (and isn't present by
>> default -- tried
>> adding the unlock/lock -- no difference.
>>
>> Weird. *sigh*
>>
>> Hi, Linda
>>
>> Do you have the BUG log after applied this patch?
>>
>> bond->lock seems to be the only one who will add the preempt_count, the
>> patch should works...
>>
>> And have you tried the 3.9.0-rc1, is the issue still exist?
>>
>> Regards,
>> Michael Wang
> -------------------
>
> What do you mean by 'bug log', do you mean kernel log --- including
> the log from boot, in case anything weird pops out, but bug happens
> edited out stretch of repetitious looking stuff that was unlikely to
> be related...
But do you have the log after applied the change which unlock bond->lock
before enter bond_update_speed_duplex() ? you mentioned that the fix
doesn't address the problem, but I'd like to take a look at the log, may
be there will be more clue ;-)
And have you tried 3.9.0-rc1? may be the issue already solved.
Regards,
Michael Wang
>
>
> [ 0.000000] Initializing cgroup subsys cpuset
> [ 0.000000] Initializing cgroup subsys cpu
> [ 0.000000] Linux version 3.8.1-Isht-Van (law@Ishtar) (gcc version
> 4.6.2 (SUSE Linux) ) #6 SMP PREEMPT Fri Mar 1 20:29:32 PST 2013
> [ 0.000000] Command line: BOOT_IMAGE=381-Isht-Van rw root=/dev/sdc1
> root=/dev/sdc1 showopts console=ttyS0,115200n8 console=tty0 elevator=cfq
> pcie_aspm=force pcie_ports=native reboot=bios
> [ 0.000000] KERNEL supported cpus:
> [ 0.000000] Intel GenuineIntel
> [ 0.000000] e820: BIOS-provided physical RAM map:
> [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009ffff] usable
> ...
> [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000c2fffffff] usable
> [ 0.000000] NX (Execute Disable) protection: active
> [ 0.000000] SMBIOS 2.6 present.
> [ 0.000000] DMI: Dell Inc. PowerEdge T610/0CX0R0, BIOS 6.1.0 10/18/2011
> [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
> [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
> [ 0.000000] e820: last_pfn = 0xc30000 max_arch_pfn = 0x400000000
> [ 0.000000] MTRR default type: uncachable
> [ 0.000000] MTRR fixed ranges enabled:
> ...
> [ 0.000000] EC000-FFFFF write-protect
> [ 0.000000] MTRR variable ranges enabled:
> [ 0.000000] 0 base 0000000000 mask FF80000000 write-back
> ...
> [ 0.000000] 7 base 0C00000000 mask FFC0000000 write-back
> [ 0.000000] 8 disabled
> [ 0.000000] 9 disabled
> [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new
> 0x7010600070106
> [ 0.000000] e820: update [mem 0xd0000000-0xffffffff] usable ==> reserved
> [ 0.000000] e820: last_pfn = 0xcf379 max_arch_pfn = 0x400000000
> [ 0.000000] initial memory mapped: [mem 0x00000000-0x1fffffff]
> [ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
> [ 0.000000] Using GB pages for direct mapping
> [ 0.000000] init_memory_mapping: [mem 0x00000000-0xcf378fff]
> [ 0.000000] [mem 0x00000000-0xbfffffff] page 1G
> [ 0.000000] [mem 0xc0000000-0xcf1fffff] page 2M
> [ 0.000000] [mem 0xcf200000-0xcf378fff] page 4k
> [ 0.000000] kernel direct mapping tables up to 0xcf378fff @ [mem
> 0x1fffd000-0x1fffffff]
> [ 0.000000] init_memory_mapping: [mem 0x100000000-0xc2fffffff]
> [ 0.000000] [mem 0x100000000-0xbffffffff] page 1G
> [ 0.000000] [mem 0xc00000000-0xc2fffffff] page 2M
> [ 0.000000] kernel direct mapping tables up to 0xc2fffffff @ [mem
> 0xcf377000-0xcf378fff]
> [ 0.000000] ACPI: RSDP 00000000000f1170 00024 (v02 DELL )
> ...
> [ 0.000000] ACPI: TCPA 00000000cf3b3f34 00064 (v02 DELL PE_SC3
> 00000001 DELL 00000001)
> [ 0.000000] ACPI: SSDT 00000000cf3b7000 037A4 (v01 INTEL PPM RCM
> 80000001 INTL 20061109)
> [ 0.000000] ACPI: Local APIC address 0xfee00000
> ...
> [ 0.000000] SRAT: PXM 2 -> APIC 0x14 -> Node 1
> [ 0.000000] SRAT: Node 1 PXM 2 [mem 0x00000000-0xcfffffff]
> [ 0.000000] SRAT: Node 1 PXM 2 [mem 0x100000000-0x62fffffff]
> [ 0.000000] SRAT: Node 0 PXM 1 [mem 0x630000000-0xc2fffffff]
> [ 0.000000] NUMA: Node 1 [mem 0x00000000-0xcfffffff] + [mem
> 0x100000000-0x62fffffff] -> [mem 0x00000000-0x62fffffff]
> [ 0.000000] Initmem setup node 0 [mem 0x630000000-0xc2fffffff]
> [ 0.000000] NODE_DATA [mem 0xc2fffd000-0xc2fffffff]
> [ 0.000000] Initmem setup node 1 [mem 0x00000000-0x62fffffff]
> [ 0.000000] NODE_DATA [mem 0x62fffd000-0x62fffffff]
> [ 0.000000] [ffffea0000000000-ffffea0018bfffff] PMD ->
> [ffff880617e00000-ffff88062fdfffff] on node 1
> [ 0.000000] [ffffea0018c00000-ffffea0030bfffff] PMD ->
> [ffff880c17600000-ffff880c2f5fffff] on node 0
> [ 0.000000] Zone ranges:
> [ 0.000000] DMA [mem 0x00001000-0x00ffffff]
> [ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
> [ 0.000000] Normal [mem 0x100000000-0xc2fffffff]
> [ 0.000000] Movable zone start for each node
> [ 0.000000] Early memory node ranges
> [ 0.000000] node 1: [mem 0x00001000-0x0009ffff]
> [ 0.000000] node 1: [mem 0x00100000-0xcf378fff]
> [ 0.000000] node 1: [mem 0x100000000-0x62fffffff]
> [ 0.000000] node 0: [mem 0x630000000-0xc2fffffff]
> [ 0.000000] On node 0 totalpages: 6291456
> [ 0.000000] Normal zone: 98304 pages used for memmap
> [ 0.000000] Normal zone: 6193152 pages, LIFO batch:31
> [ 0.000000] On node 1 totalpages: 6288152
> [ 0.000000] DMA zone: 64 pages used for memmap
> [ 0.000000] DMA zone: 8 pages reserved
> [ 0.000000] DMA zone: 3927 pages, LIFO batch:0
> [ 0.000000] DMA32 zone: 13198 pages used for memmap
> [ 0.000000] DMA32 zone: 831467 pages, LIFO batch:31
> [ 0.000000] Normal zone: 84992 pages used for memmap
> [ 0.000000] Normal zone: 5354496 pages, LIFO batch:31
> [ 0.000000] ACPI: PM-Timer IO Port: 0x808
> [ 0.000000] ACPI: Local APIC address 0xfee00000
> ...
> [ 0.000000] ACPI: LAPIC (acpi_id[0x20] lapic_id[0xff] disabled)
> [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
> [ 0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
> [ 0.000000] IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI
> 0-23
> [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec80000] gsi_base[32])
> [ 0.000000] IOAPIC[1]: apic_id 1, version 32, address 0xfec80000, GSI
> 32-55
> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> [ 0.000000] ACPI: IRQ0 used by override.
> [ 0.000000] ACPI: IRQ2 used by override.
> [ 0.000000] ACPI: IRQ9 used by override.
> [ 0.000000] Using ACPI (MADT) for SMP configuration information
> [ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
> [ 0.000000] smpboot: 32 Processors exceeds NR_CPUS limit of 12
> [ 0.000000] smpboot: Allowing 12 CPUs, 0 hotplug CPUs
> [ 0.000000] nr_irqs_gsi: 72
> [ 0.000000] e820: [mem 0xd0000000-0xdfffffff] available for PCI devices
> [ 0.000000] setup_percpu: NR_CPUS:12 nr_cpumask_bits:12 nr_cpu_ids:12
> nr_node_ids:2
> [ 0.000000] PERCPU: Embedded 476 pages/cpu @ffff880617200000 s1918016
> r8192 d23488 u2097152
> [ 0.000000] pcpu-alloc: s1918016 r8192 d23488 u2097152 alloc=1*2097152
> [ 0.000000] pcpu-alloc: [0] 00 [0] 02 [0] 04 [0] 06 [0] 08 [0] 10 [1]
> 01 [1] 03
> [ 0.000000] pcpu-alloc: [1] 05 [1] 07 [1] 09 [1] 11
> [ 0.000000] Built 2 zonelists in Zone order, mobility grouping on.
> Total pages: 12383042
> [ 0.000000] Policy zone: Normal
> [ 0.000000] Kernel command line: reboot=bios BOOT_IMAGE=381-Isht-Van
> rw root=/dev/sdc1 root=/dev/sdc1 showopts console=ttyS0,115200n8
> console=tty0 elevator=cfq pcie_aspm=force pcie_ports=native reboot=bios
> [ 0.000000] PCIe ASPM is forcibly enabled
> [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
> [ 0.000000] __ex_table already sorted, skipping sort
> [ 0.000000] Memory: 49417684k/51118080k available (6379k kernel code,
> 799648k absent, 900748k reserved, 6697k data, 2356k init)
> [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0,
> CPUs=12, Nodes=2
> [ 0.000000] Preemptible hierarchical RCU implementation.
> [ 0.000000] NR_IRQS:4352 nr_irqs:1320 16
> [ 0.000000] Extended CMOS year: 2000
> [ 0.000000] Console: colour VGA+ 132x43
> [ 0.000000] console [tty0] enabled
> [ 0.000000] console [ttyS0] enabled
> ...
> [ 0.000000] Enabling automatic NUMA balancing. Configure with
> numa_balancing= or sysctl
> [ 0.000000] hpet clockevent registered
> [ 0.000000] tsc: Fast TSC calibration using PIT
> [ 0.001000] tsc: Detected 2793.076 MHz processor
> [ 0.000004] Calibrating delay loop (skipped), value calculated using
> timer frequency.. 5586.15 BogoMIPS (lpj=2793076)
> [ 0.010813] pid_max: default: 32768 minimum: 301
> [ 0.015614] Security Framework initialized
> [ 0.023350] Dentry cache hash table entries: 8388608 (order: 14,
> 67108864 bytes)
> [ 0.044185] Inode-cache hash table entries: 4194304 (order: 13,
> 33554432 bytes)
> [ 0.057474] Mount-cache hash table entries: 256
> ...
> [ 0.089812] CPU: Physical Processor ID: 1
> [ 0.093952] CPU: Processor Core ID: 0
> [ 0.097757] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
> [ 0.097757] ENERGY_PERF_BIAS: View and update with
> x86_energy_perf_policy(8)
> [ 0.110967] mce: CPU supports 9 MCE banks
> [ 0.115114] CPU0: Thermal monitoring enabled (TM1)
> [ 0.120048] process: using mwait in idle threads
> [ 0.124793] Last level iTLB entries: 4KB 512, 2MB 7, 4MB 7
> [ 0.124793] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32
> [ 0.124793] tlb_flushall_shift: 6
> [ 0.139667] Freeing SMP alternatives: 20k freed
> [ 0.144332] ACPI: Core revision 20121018
> [ 0.152164] dmar: Host address width 40
> [ 0.156136] dmar: DRHD base: 0x000000fed90000 flags: 0x1
> [ 0.161569] dmar: IOMMU 0: reg_base_addr fed90000 ver 1:0 cap
> c90780106f0462 ecap f020f6
> ...
> [ 0.224974] dmar: RMRR base: 0x000000cf4c2000 end: 0x000000cf4c2fff
> [ 0.231442] dmar: ATSR flags: 0x0
> [ 0.235046] Switched APIC routing to physical flat.
> [ 0.240639] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
> [ 0.256738] smpboot: CPU0: Intel(R) Xeon(R) CPU X5660 @
> 2.80GHz (fam: 06, model: 2c, stepping: 02)
> [ 0.368291] Performance Events: PEBS fmt1+, 16-deep LBR, Westmere
> events, Intel PMU driver.
> [ 0.376959] perf_event_intel: CPUID marked event: 'bus cycles'
> unavailable
> [ 0.383937] ... version: 3
> [ 0.388059] ... bit width: 48
> [ 0.392282] ... generic registers: 4
> [ 0.396395] ... value mask: 0000ffffffffffff
> [ 0.401818] ... max period: 000000007fffffff
> [ 0.407240] ... fixed-purpose events: 3
> [ 0.411353] ... event mask: 000000070000000f
> [ 0.424313] SMP alternatives: lockdep: fixing up alternatives
> [ 0.526339] NMI watchdog: enabled on all CPUs, permanently consumes
> one hw-PMU counter.
> [ 0.430197] smpboot: Booting Node 1, Processors #1
> ...
> [ 0.767737] smpboot: Booting Node 0, Processors #10
> [ 0.787660] SMP alternatives: lockdep: fixing up alternatives
> [ 0.793815] OK
> [ 0.795696] smpboot: Booting Node 1, Processors #11 OK
> [ 0.814480] Brought up 12 CPUs
> [ 0.817643] smpboot: Total of 12 processors activated (67031.54 BogoMIPS)
> [ 0.837389] devtmpfs: initialized
> [ 0.841517] NET: Registered protocol family 16
> [ 0.846297] i2c-core: driver [dummy] registered
> [ 0.846445] ACPI FADT declares the system doesn't support PCIe ASPM,
> so disable it
> [ 0.854119] ACPI: bus type pci registered
> [ 0.858333] dca service started, version 1.12.1
> [ 0.863002] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem
> 0xe0000000-0xefffffff] (base 0xe0000000)
> [ 0.872412] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
> [ 0.915444] PCI: Using configuration type 1 for base access
> [ 0.923541] bio: create slab <bio-0> at 0
> [ 0.927876] ACPI: Added _OSI(Module Device)
> [ 0.932207] ACPI: Added _OSI(Processor Device)
> [ 0.936769] ACPI: Added _OSI(3.0 _SCP Extensions)
> [ 0.941613] ACPI: Added _OSI(Processor Aggregator Device)
> [ 0.949347] ACPI: EC: Look up EC in DSDT
> [ 0.952568] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
> [ 0.962779] ACPI: Interpreter enabled
> [ 0.966551] ACPI: (supports S0 S5)
> [ 0.970176] ACPI: Using IOAPIC for interrupt routing
> [ 0.982895] HEST: Table parsing has been initialized.
> [ 0.988063] PCI: Using host bridge windows from ACPI; if necessary,
> use "pci=nocrs" and report a bug
> [ 0.997500] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
> [ 1.003792] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> [ 1.004949] pci_root PNP0A08:00: Requesting ACPI _OSC control (0x15)
> [ 1.011897] pci_root PNP0A08:00: ACPI _OSC control (0x15) granted
> [ 1.018511] PCI host bridge to bus 0000:00
> [ 1.022727] pci_bus 0000:00: root bus resource [bus 00-ff]
> ...
> [ 1.054860] pci_bus 0000:00: root bus resource [mem
> 0xfed40000-0xfed44fff]
> [ 1.065200] pci 0000:00:00.0: [8086:3406] type 00 class 0x060000
> ...
> [ 1.066442] pci 0000:00:16.0: [8086:3430] type 00 class 0x088000
> [ 1.066459] pci 0000:00:16.0: reg 10: [mem 0xdf0e0000-0xdf0e3fff 64bit]
> ...
> [ 1.067245] pci 0000:00:16.7: [8086:342c] type 00 class 0x088000
> [ 1.067261] pci 0000:00:16.7: reg 10: [mem 0xdf0fc000-0xdf0fffff 64bit]
> [ 1.067362] pci 0000:00:1a.0: [8086:2937] type 00 class 0x0c0300
> ...
> [ 1.144174] pci 0000:00:1e.0: bridge window [mem
> 0xd0000000-0xfdffffff] (subtractive decode)
> [ 1.144176] pci 0000:00:1e.0: bridge window [mem
> 0xfed40000-0xfed44fff] (subtractive decode)
> [ 1.144234] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
> ...
> [ 1.201823] ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 14
> 15) *0, disabled.
> [ 1.210634] ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 *5 6 7 10 11 14 15)
> [ 1.218252] SCSI subsystem initialized
> [ 1.222118] ACPI: bus type scsi registered
> [ 1.226390] libata version 3.00 loaded.
> [ 1.226405] ACPI: bus type usb registered
> [ 1.230546] usbcore: registered new interface driver usbfs
> [ 1.236210] usbcore: registered new interface driver hub
> [ 1.241673] usbcore: registered new device driver usb
> [ 1.246856] pps_core: LinuxPPS API ver. 1 registered
> [ 1.251935] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
> Rodolfo Giometti <[email protected]>
> [ 1.261180] PTP clock support registered
> [ 1.265251] PCI: Using ACPI for IRQ routing
> [ 1.276548] PCI: Discovered peer bus fe
> [ 1.280502] PCI: root bus fe: using default resources
> [ 1.280503] PCI: Probing PCI hardware (bus fe)
> [ 1.280544] PCI host bridge to bus 0000:fe
> [ 1.284756] pci_bus 0000:fe: root bus resource [io 0x0000-0xffff]
> [ 1.291039] pci_bus 0000:fe: root bus resource [mem
> 0x00000000-0xffffffffff]
> [ 1.298198] pci_bus 0000:fe: No busn resource found for root bus,
> will use [bus fe-ff]
> [ 1.306219] pci 0000:fe:00.0: [8086:2c70] type 00 class 0x060000
> ...
> [ 1.307032] pci 0000:fe:06.3: [8086:2db3] type 00 class 0x060000
> [ 1.307092] pci_bus 0000:fe: busn_res: [bus fe-ff] end is updated to fe
> [ 1.307859] PCI: Discovered peer bus ff
> [ 1.311814] PCI: root bus ff: using default resources
> [ 1.311815] PCI: Probing PCI hardware (bus ff)
> [ 1.311850] PCI host bridge to bus 0000:ff
> [ 1.316053] pci_bus 0000:ff: root bus resource [io 0x0000-0xffff]
> [ 1.322346] pci_bus 0000:ff: root bus resource [mem
> 0x00000000-0xffffffffff]
> [ 1.329504] pci_bus 0000:ff: No busn resource found for root bus,
> will use [bus ff-ff]
> [ 1.337525] pci 0000:ff:00.0: [8086:2c70] type 00 class 0x060000
> ...
> [ 1.338386] pci 0000:ff:06.3: [8086:2db3] type 00 class 0x060000
> [ 1.338450] pci_bus 0000:ff: busn_res: [bus ff] end is updated to ff
> [ 1.339197] PCI: pci_cache_line_size set to 64 bytes
> [ 1.339469] e820: reserve RAM buffer [mem 0xcf379000-0xcfffffff]
> [ 1.339687] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
> [ 1.345199] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
> [ 1.353153] Switching to clocksource hpet
> [ 1.369117] FS-Cache: Loaded
> [ 1.372138] pnp: PnP ACPI init
> [ 1.375319] ACPI: bus type pnp registered
> [ 1.379569] pnp 00:00: [dma 4]
> ...
> [ 1.455138] pnp 00:0a: Plug and Play ACPI device, IDs PNP0103 (active)
> [ 1.455269] system 00:0b: [mem 0xfed90000-0xfed91fff] could not be
> reserved
> [ 1.462353] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
> [ 1.462732] pnp: PnP ACPI: found 12 devices
> [ 1.467044] ACPI: ACPI bus type pnp unregistered
> [ 1.481774] pci 0000:06:00.1: address space collision: [mem
> 0xdf300000-0xdf37ffff pref] conflicts with 0000:06:00.0 [mem
> 0xdf300000-0xdf37ffff pref]
> [ 1.495395] pci 0000:00:01.0: PCI bridge to [bus 01]
> [ 1.500484] pci 0000:00:01.0: bridge window [mem 0xda000000-0xddffffff]
> ...
> [ 1.611994] pci 0000:00:1e.0: bridge window [mem 0xde000000-0xdeffffff]
> [ 1.623952] pci 0000:00:1e.0: bridge window [mem
> 0xd9000000-0xd97fffff 64bit pref]
> [ 1.631898] pci 0000:00:1e.0: setting latency timer to 64
> ...
> [ 1.631951] pci_bus 0000:ff: resource 5 [mem 0x00000000-0xffffffffff]
> [ 1.632012] NET: Registered protocol family 2
> [ 1.637148] TCP established hash table entries: 524288 (order: 11,
> 8388608 bytes)
> [ 1.646389] TCP bind hash table entries: 65536 (order: 10, 5242880 bytes)
> ...
> [ 1.815851] IOMMU: Setting identity map for device 0000:00:1a.7
> [0xcf4c8000 - 0xcf4dffff]
> [ 1.824137] IOMMU: Setting identity map for device 0000:00:1d.7
> [0xcf4c8000 - 0xcf4dffff]
> [ 1.832424] IOMMU: Prepare 0-16MiB unity mapping for LPC
> [ 1.837883] IOMMU: Setting identity map for device 0000:00:1f.0 [0x0
> - 0xffffff]
> [ 1.845592] PCI-DMA: Intel(R) Virtualization Technology for Directed I/O
> ...
> [ 1.923963] microcode: CPU11 sig=0x206c2, pf=0x1, revision=0x15
> [ 1.930096] microcode: Microcode Update Driver: v2.00
> <[email protected]>, Peter Oruba
> [ 1.939117] sha1_ssse3: Using SSSE3 optimized SHA-1 implementation
> [ 1.939131] cryptomgr_test (77) used greatest stack depth: 5832 bytes
> left
> [ 1.954626] HugeTLB registered 2 MB page size, pre-allocated 0 pages
> [ 1.965735] Key type cifs.idmap registered
> [ 1.970070] SGI XFS with ACLs, security attributes, realtime, large
> block/inode numbers, no debug enabled
> [ 1.980271] msgmni has been set to 32768
> [ 1.985133] cryptomgr_test (97) used greatest stack depth: 5776 bytes
> left
> [ 1.985471] alg: No test for stdrng (krng)
> [ 1.985539] Block layer SCSI generic (bsg) driver version 0.4 loaded
> (major 250)
> [ 1.985596] io scheduler noop registered
> [ 1.985643] io scheduler cfq registered (default)
> ...
> [ 1.987902] pcieport 0000:00:0a.0: irq 79 for MSI/MSI-X
> [ 1.988057] pcieport 0000:00:01.0: Signaling PME through PCIe PME
> interrupt
> ...
> [ 1.988274] pcie_pme 0000:00:0a.0:pcie01: service driver pcie_pme loaded
> [ 1.988375] intel_idle: MWAIT substates: 0x1120
> [ 1.988375] intel_idle: v0.4 model 0x2C
> [ 1.988376] intel_idle: lapic_timer_reliable_states 0xffffffff
> [ 2.115394] cryptomgr_test (99) used greatest stack depth: 5208 bytes
> left
> [ 2.122414] ipmi message handler version 39.2
> [ 2.126909] ipmi device interface
> [ 2.130384] IPMI System Interface driver.
> [ 2.134590] ipmi_si: probing via SMBIOS
> [ 2.138537] ipmi_si: SMBIOS: io 0xca8 regsize 1 spacing 4 irq 0
> [ 2.144571] ipmi_si: Adding SMBIOS-specified kcs state machine
> [ 2.150581] ipmi_si: Trying SMBIOS-specified kcs state machine at i/o
> address 0xca8, slave address 0x20, irq 0
> [ 2.376680] ipmi_si ipmi_si.0: Found new BMC (man_id: 0x0002a2,
> prod_id: 0x0100, dev_id: 0x20)
> [ 2.385509] ipmi_si ipmi_si.0: IPMI kcs interface initialized
> [ 2.391506] ERST: Error Record Serialization Table (ERST) support is
> initialized.
> [ 2.399478] GHES: APEI firmware first mode is enabled by APEI bit and
> WHEA _OSC.
> [ 2.406995] ioatdma: Intel(R) QuickData Technology Driver 4.00
> ...
> [ 2.416327] ioatdma 0000:00:16.7: irq 87 for MSI/MSI-X
> [ 2.450434] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
> [ 2.480844] 00:04: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> [ 2.507130] 00:05: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> [ 2.513742] Non-volatile memory driver v1.3
> [ 2.521604] brd: module loaded
> [ 2.526285] loop: module loaded
> [ 2.530376] nbd: registered device at major 43
> [ 2.537559] gpio_ich: GPIO from 195 to 255 on gpio_ich
> [ 2.543005] Loading iSCSI transport class v2.0-870.
> [ 2.548103] megasas: 06.504.01.00-rc1 Mon. Oct. 1 17:00:00 PDT 2012
> [ 2.554547] megasas: 0x1000:0x0079:0x1000:0x9275: bus 5:slot 0:func 0
> [ 2.561326] megasas: FW now in Ready state
> ...
> [ 2.844408] scsi 0:0:29:0: Direct-Access ATA Hitachi
> HUA72202 A3EA PQ: 0 ANSI: 5
> ...
> [ 2.958508] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April
> 27, 2011)
> [ 2.959107] bnx2: Broadcom NetXtreme II Gigabit Ethernet Driver bnx2
> v2.2.3 (June 27, 2012)
> [ 2.959422] scsi 1:0:4:0: Direct-Access ATA Hitachi HUA72202
> A3EA PQ: 0 ANSI: 5
> [ 2.959720] bnx2 0000:01:00.0 eth0: Broadcom NetXtreme II BCM5709
> 1000Base-T (C0) PCI Express found at mem da000000, IRQ 36, node addr
> 00:26:b9:2c:a4:ef
> [ 2.960305] bnx2 0000:01:00.1 eth1: Broadcom NetXtreme II BCM5709
> 1000Base-T (C0) PCI Express found at mem dc000000, IRQ 48, node addr
> 00:26:b9:2c:a4:f1
> [ 2.960347] e1000e: Intel(R) PRO/1000 Network Driver - 2.1.4-k
> [ 2.960348] e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
> [ 2.960377] e1000e 0000:03:00.0: Disabling ASPM L1
> [ 2.960470] e1000e 0000:03:00.0: Interrupt Throttling Rate (ints/sec)
> set to dynamic conservative mode
> [ 2.960511] e1000e 0000:03:00.0: irq 89 for MSI/MSI-X
> [ 3.007831] scsi 1:0:5:0: Direct-Access ATA Hitachi HUA72202
> A3EA PQ: 0 ANSI: 5
> ...
> [ 3.127317] scsi 0:0:39:0: Direct-Access ATA Hitachi
> HUA72202 A3EA PQ: 0 ANSI: 5
> [ 3.132612] e1000e 0000:03:00.0 eth2: (PCI Express:2.5GT/s:Width x4)
> 00:15:17:bf:be:b2
> [ 3.132614] e1000e 0000:03:00.0 eth2: Intel(R) PRO/1000 Network
> Connection
> [ 3.132689] e1000e 0000:03:00.0 eth2: MAC: 0, PHY: 4, PBA No: C57721-005
> [ 3.132702] e1000e 0000:03:00.1: Disabling ASPM L1
> [ 3.132795] e1000e 0000:03:00.1: Interrupt Throttling Rate (ints/sec)
> set to dynamic conservative mode
> [ 3.132836] e1000e 0000:03:00.1: irq 90 for MSI/MSI-X
> [ 3.159261] Uhhuh. NMI received for unknown reason 31 on CPU 0.
> [ 3.159261] Do you have a strange power saving mode enabled?
> [ 3.159262] Dazed and confused, but trying to continue
> [ 3.188918] dmar: DRHD: handling fault status reg 2
> [ 3.193907] dmar: DMAR:[DMA Read] Request device [02:00.0] fault addr
> ffe76000
> [ 3.193907] DMAR:[fault reason 06] PTE Read access is not set
> [ 3.240182] scsi 0:2:0:0: Direct-Access LSI MR9280DE-8e
> 2.0. PQ: 0 ANSI: 5
> [ 3.248746] scsi 0:2:1:0: Direct-Access LSI MR9280DE-8e
> 2.0. PQ: 0 ANSI: 5
> [ 3.282652] dmar: DRHD: handling fault status reg 102
> [ 3.284312] ses 0:0:14:0: Attached Enclosure device
> [ 3.284426] ses 0:0:14:0: Attached scsi generic sg0 type 13
> [ 3.301981] dmar: DMAR:[DMA Read] Request device [02:00.0] fault addr
> ffe8a000
> [ 3.301981] DMAR:[fault reason 06] PTE Read access is not set
> [ 3.305305] e1000e 0000:03:00.1 eth3: (PCI Express:2.5GT/s:Width x4)
> 00:15:17:bf:be:b3
> [ 3.305307] e1000e 0000:03:00.1 eth3: Intel(R) PRO/1000 Network
> Connection
> [ 3.305382] e1000e 0000:03:00.1 eth3: MAC: 0, PHY: 4, PBA No: C57721-005
> [ 3.305431] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver -
> version 3.11.33-k
> [ 3.305431] ixgbe: Copyright (c) 1999-2012 Intel Corporation.
> [ 3.350903] scsi 1:0:32:0: Enclosure DP
> BACKPLANE 1.07 PQ: 0 ANSI: 5
> [ 3.359344] dmar: DRHD: handling fault status reg 202
> [ 3.364534] dmar: DMAR:[DMA Read] Request device [02:00.0] fault addr
> ffe89000
> [ 3.364534] DMAR:[fault reason 06] PTE Read access is not set
> [ 3.386416] ses 0:0:27:0: Attached Enclosure device
> ...
> [ 3.508700] sd 0:2:1:0: [sdb] Attached SCSI disk
> [ 3.622261] ses 1:0:32:0: Attached Enclosure device
> [ 3.627372] ses 1:0:32:0: Attached scsi generic sg4 type 13
> [ 3.733753] ixgbe 0000:06:00.0: irq 91 for MSI/MSI-X
> [ 3.733763] ixgbe 0000:06:00.0: irq 92 for MSI/MSI-X
> [ 3.733772] ixgbe 0000:06:00.0: irq 93 for MSI/MSI-X
> [ 3.733780] ixgbe 0000:06:00.0: irq 94 for MSI/MSI-X
> [ 3.733789] ixgbe 0000:06:00.0: irq 95 for MSI/MSI-X
> [ 3.733797] ixgbe 0000:06:00.0: irq 96 for MSI/MSI-X
> [ 3.733805] ixgbe 0000:06:00.0: irq 97 for MSI/MSI-X
> [ 3.733814] ixgbe 0000:06:00.0: irq 98 for MSI/MSI-X
> [ 3.733822] ixgbe 0000:06:00.0: irq 99 for MSI/MSI-X
> [ 3.733831] ixgbe 0000:06:00.0: irq 100 for MSI/MSI-X
> [ 3.733839] ixgbe 0000:06:00.0: irq 101 for MSI/MSI-X
> [ 3.733847] ixgbe 0000:06:00.0: irq 102 for MSI/MSI-X
> [ 3.733856] ixgbe 0000:06:00.0: irq 103 for MSI/MSI-X
> [ 3.733933] ixgbe 0000:06:00.0: Multiqueue Enabled: Rx Queue count =
> 12, Tx Queue count = 12
> [ 3.742464] dmar: DRHD: handling fault status reg 302
> [ 3.742467] dmar: DMAR:[DMA Read] Request device [02:00.0] fault addr
> ffe86000
> [ 3.742467] DMAR:[fault reason 06] PTE Read access is not set
> [ 3.805353] dmar: DRHD: handling fault status reg 402
> [ 3.810529] dmar: DMAR:[DMA Read] Request device [02:00.0] fault addr
> ffe87000
> [ 3.810529] DMAR:[fault reason 06] PTE Read access is not set
> [ 3.820908] ixgbe 0000:06:00.0: (PCI Express:5.0GT/s:Width x8)
> a0:36:9f:15:c9:c0
> [ 3.889229] dmar: DRHD: handling fault status reg 502
> [ 3.894389] dmar: DMAR:[DMA Read] Request device [02:00.0] fault addr
> ffe84000
> [ 3.894389] DMAR:[fault reason 06] PTE Read access is not set
> ...
> [ 4.037793] sd 1:2:0:0: [sdc] Attached SCSI disk
> [ 4.062063] dmar: DRHD: handling fault status reg 702
> [ 4.067233] dmar: DMAR:[DMA Read] Request device [02:00.0] fault addr
> ffe7f000
> [ 4.067233] DMAR:[fault reason 06] PTE Read access is not set
> [ 4.100647] sdd: sdd1
> [ 4.103655] sd 1:2:1:0: [sdd] Attached SCSI disk
> [ 4.123872] ixgbe 0000:06:00.0: Intel(R) 10 Gigabit Network Connection
> [ 4.558317] ixgbe 0000:06:00.1: irq 104 for MSI/MSI-X
> [ 4.558326] ixgbe 0000:06:00.1: irq 105 for MSI/MSI-X
> [ 4.558335] ixgbe 0000:06:00.1: irq 106 for MSI/MSI-X
> [ 4.558343] ixgbe 0000:06:00.1: irq 107 for MSI/MSI-X
> [ 4.558351] ixgbe 0000:06:00.1: irq 108 for MSI/MSI-X
> [ 4.558360] ixgbe 0000:06:00.1: irq 109 for MSI/MSI-X
> [ 4.558368] ixgbe 0000:06:00.1: irq 110 for MSI/MSI-X
> [ 4.558376] ixgbe 0000:06:00.1: irq 111 for MSI/MSI-X
> [ 4.558385] ixgbe 0000:06:00.1: irq 112 for MSI/MSI-X
> [ 4.558393] ixgbe 0000:06:00.1: irq 113 for MSI/MSI-X
> [ 4.558401] ixgbe 0000:06:00.1: irq 114 for MSI/MSI-X
> [ 4.558410] ixgbe 0000:06:00.1: irq 115 for MSI/MSI-X
> [ 4.558418] ixgbe 0000:06:00.1: irq 116 for MSI/MSI-X
> [ 4.558490] ixgbe 0000:06:00.1: Multiqueue Enabled: Rx Queue count =
> 12, Tx Queue count = 12
> [ 4.627063] ixgbe 0000:06:00.1: (PCI Express:5.0GT/s:Width x8)
> a0:36:9f:15:c9:c2
> [ 4.794640] ixgbe 0000:06:00.1: MAC: 3, PHY: 3, PBA No: G45270-002
> [ 4.943908] ixgbe 0000:06:00.1: Intel(R) 10 Gigabit Network Connection
> [ 4.950603] I2O subsystem v1.325
> [ 4.953953] i2o: max drivers = 8
> ...
> [ 5.519890] usbserial: USB Serial support registered for generic
> [ 5.526107] i8042: PNP: No PS/2 controller found. Probing ports directly.
> [ 5.535870] serio: i8042 KBD port at 0x60,0x64 irq 1
> [ 5.541055] serio: i8042 AUX port at 0x60,0x64 irq 12
> [ 5.549583] usbcore: registered new interface driver wacom
> [ 5.555277] input: PC Speaker as /devices/platform/pcspkr/input/input0
> [ 5.562198] rtc_cmos 00:03: RTC can wake from S4
> [ 5.567265] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
> [ 5.574040] rtc0: alarms up to one day, y3k, 242 bytes nvram, hpet irqs
> [ 5.580796] i2c /dev entries driver
> [ 5.585128] ACPI Error: No handler for Region [IPMI]
> (ffff880613c39240) [IPMI] (20121018/evregion-376)
> [ 5.594665] ACPI Error: Region IPMI (ID=7) has no handler
> (20121018/exfldio-305)
> [ 5.602573] ACPI Error: Method parse/execution failed
> [\_SB_.PMI0._GHL] (Node ffff880613c38b18), AE_NOT_EXIST
> (20121018/psparse-537)
> [ 5.614909] ACPI Error: Method parse/execution failed
> [\_SB_.PMI0._PMC] (Node ffff880613c38a78), AE_NOT_EXIST
> (20121018/psparse-537)
> [ 5.627254] ACPI Exception: AE_NOT_EXIST, Evaluating _PMC
> (20121018/power_meter-753)
> [ 5.635332] coretemp coretemp.1: TjMax is 96 degrees C
> ...
> [ 5.635573] coretemp coretemp.0: TjMax is 96 degrees C
> [ 5.635834] device-mapper: uevent: version 1.0.3
> [ 5.640724] device-mapper: ioctl: 4.23.1-ioctl (2012-12-18)
> initialised: [email protected]
> [ 5.649319] EDAC MC: Ver: 3.0.0
> [ 5.653653] EDAC MC1: Giving out device to 'i7core_edac.c' 'i7 core
> #1': DEV 0000:fe:03.0
> [ 5.662012] EDAC PCI0: Giving out device to module 'i7core_edac'
> controller 'EDAC PCI controller': DEV '0000:fe:03.0' (POLLED)
> [ 5.674123] EDAC MC0: Giving out device to 'i7core_edac.c' 'i7 core
> #0': DEV 0000:ff:03.0
> [ 5.682450] EDAC PCI1: Giving out device to module 'i7core_edac'
> controller 'EDAC PCI controller': DEV '0000:ff:03.0' (POLLED)
> [ 5.694321] EDAC i7core: Driver loaded, 2 memory controller(s) found.
> [ 5.701319] cpuidle: using governor ladder
> [ 5.706287] cpuidle: using governor menu
> [ 5.711285] EFI Variables Facility v0.08 2004-May-17
> [ 5.716452] dcdbas dcdbas: Dell Systems Management Base Driver
> (version 5.6.0-3.2)
> [ 5.724250] usbcore: registered new interface driver usbhid
> [ 5.729946] usbhid: USB HID core driver
> [ 5.733841] usb 7-1: new low-speed USB device number 2 using uhci_hcd
> [ 5.740464] GACT probability on
> [ 5.743781] Netfilter messages via NETLINK v0.30.
> [ 5.748733] ip_tables: (C) 2000-2006 Netfilter Core Team
> [ 5.754795] TCP: highspeed registered
> [ 5.758606] TCP: htcp registered
> [ 5.761957] TCP: scalable registered
> [ 5.765638] TCP: lp registered
> [ 5.768828] NET: Registered protocol family 17
> [ 5.773416] Key type dns_resolver registered
> [ 5.778771] registered taskstats version 1
> [ 5.785472] console [netcon0] enabled
> [ 5.789268] netconsole: network logging started
> [ 5.794417] rtc_cmos 00:03: setting system clock to 2013-03-03
> 13:36:33 UTC (1362317793)
> ...
> [ 6.034685] Freeing unused kernel memory: 2356k freed
> [ 6.040393] Write protecting the kernel read-only data: 12288k
> [ 6.055099] Freeing unused kernel memory: 1804k freed
> [ 6.066535] Freeing unused kernel memory: 1296k freed
> ...
> [ 7.272433] XFS (sdc6): Ending clean mount
> [ 8.729858] ACPI: Requesting acpi_cpufreq
> [ 8.736906] mousedev: PS/2 mouse device common for all mice
> [ 8.740862] Uhhuh. NMI received for unknown reason 31 on CPU 0.
> [ 8.740862] Do you have a strange power saving mode enabled?
> [ 8.740863] Dazed and confused, but trying to continue
> [ 8.763852] input: Power Button as
> /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
> [ 8.771464] ACPI: Power Button [PWRF]
> [ 8.816722] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
> [ 8.822886] iTCO_wdt: Found a ICH9 TCO device (Version=2, TCOBASE=0x0860)
> [ 8.830275] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
> [ 8.871909] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work
> properly. Using workaround
> [ 9.311531] Adding 8393924k swap on /dev/sdc5. Priority:-1 extents:1
> across:8393924k
> [ 9.898467] bio: create slab <bio-1> at 1
> [ 10.320156] bio: create slab <bio-2> at 2
> [ 12.848010] XFS (sdc2): Mounting Filesystem
> ...
> [ 14.534075] XFS (dm-6): Ending clean mount
> [ 18.538494] bonding: bond0: Setting MII monitoring interval to 250.
> [ 18.552402] bonding: bond0: Adding slave eth_s2_0.
> [ 18.620810] pps pps0: new PPS source ptp0
> [ 18.624829] ixgbe 0000:06:00.0: registered PHC device on eth_s2_0
> [ 19.055454] bonding: bond0: enslaving eth_s2_0 as an active interface
> with a down link.
> [ 19.073574] bonding: bond0: Adding slave eth_s2_1.
> [ 19.140326] pps pps1: new PPS source ptp1
> [ 19.144340] ixgbe 0000:06:00.1: registered PHC device on eth_s2_1
> [ 19.574896] bonding: bond0: enslaving eth_s2_1 as an active interface
> with a down link.
> [ 19.597337] ixgbe 0000:06:00.0 eth_s2_0: changing MTU from 1500 to 9000
> [ 20.466899] ixgbe 0000:06:00.1 eth_s2_1: changing MTU from 1500 to 9000
> [ 22.177843] e1000e 0000:03:00.0 eth0: changing MTU from 1500 to 9000
> [ 22.472021] e1000e 0000:03:00.0: irq 89 for MSI/MSI-X
> [ 22.572957] e1000e 0000:03:00.0: irq 89 for MSI/MSI-X
> [ 22.917065] e1000e 0000:03:00.1 eth1: changing MTU from 1500 to 9000
> [ 23.211319] e1000e 0000:03:00.1: irq 90 for MSI/MSI-X
> [ 23.311726] e1000e 0000:03:00.1: irq 90 for MSI/MSI-X
> [ 23.677061] bnx2 0000:01:00.0: irq 117 for MSI/MSI-X
> ...
> [ 23.677168] bnx2 0000:01:00.0: irq 125 for MSI/MSI-X
> [ 23.729930] bnx2 0000:01:00.0 eth2: using MSIX
> [ 23.730055] ip (2400) used greatest stack depth: 2096 bytes left
> [ 24.075847] bnx2 0000:01:00.1: irq 126 for MSI/MSI-X
> ...
> [ 24.075913] bnx2 0000:01:00.1: irq 134 for MSI/MSI-X
> [ 24.129293] bnx2 0000:01:00.1 eth3: using MSIX
> [ 24.776033] ixgbe 0000:06:00.0 eth_s2_0: NIC Link is Up 10 Gbps, Flow
> Control: RX/TX
> [ 24.820010] BUG: scheduling while atomic: kworker/u:2/109/0x00000002
> [ 24.826415] 4 locks held by kworker/u:2/109:
> [ 24.826425] #0: ((bond_dev->name)){......}, at:
> [<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
> [ 24.826428] #1: ((&(&bond->mii_work)->work)){......}, at:
> [<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
> [ 24.826435] #2: (rtnl_mutex){......}, at: [<ffffffff81590c00>]
> rtnl_trylock+0x10/0x20
> [ 24.826441] #3: (&bond->lock){......}, at: [<ffffffff8145af55>]
> bond_mii_monitor+0x2d5/0x630
> [ 24.826448] Modules linked in: iptable_filter kvm_intel kvm iTCO_wdt
> acpi_cpufreq mperf button mousedev processor
> [ 24.826451] Pid: 109, comm: kworker/u:2 Not tainted 3.8.1-Isht-Van #6
> [ 24.826452] Call Trace:
> [ 24.826459] [<ffffffff8162b039>] __schedule_bug+0x5e/0x6c
> [ 24.826475] [<ffffffff816345a2>] __schedule+0x762/0x7f0
> [ 24.826479] [<ffffffff81634744>] schedule+0x24/0x70
> [ 24.826488] [<ffffffff81633704>]
> schedule_hrtimeout_range_clock+0xa4/0x130
> [ 24.826495] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 24.826499] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
> [ 24.826507] [<ffffffff8163379e>] schedule_hrtimeout_range+0xe/0x10
> [ 24.826512] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
> [ 24.826518] [<ffffffff814b2d8c>] ixgbe_acquire_swfw_sync_X540+0xbc/0x100
> [ 24.826527] [<ffffffff814aeb1d>] ixgbe_read_phy_reg_generic+0x3d/0x140
> [ 24.826532] [<ffffffff814aedbc>]
> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
> [ 24.826537] [<ffffffff8145af55>] ? bond_mii_monitor+0x2d5/0x630
> [ 24.826543] [<ffffffff814a64f4>] ixgbe_get_settings+0x34/0x340
> [ 24.826546] [<ffffffff81586ac8>] __ethtool_get_settings+0x88/0x130
> [ 24.826552] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
> [ 24.826554] [<ffffffff8145afc4>] bond_mii_monitor+0x344/0x630
> [ 24.826556] [<ffffffff8105dab1>] process_one_work+0x1a1/0x5d0
> [ 24.826558] [<ffffffff8105da4d>] ? process_one_work+0x13d/0x5d0
> [ 24.826560] [<ffffffff8145ac80>] ? bond_loadbalance_arp_mon+0x300/0x300
> [ 24.826563] [<ffffffff8105ed60>] worker_thread+0x160/0x3f0
> [ 24.826565] [<ffffffff8105ec00>] ? manage_workers+0x290/0x290
> [ 24.826569] [<ffffffff81064446>] kthread+0xd6/0xe0
> [ 24.826573] [<ffffffff8107004a>] ? finish_task_switch+0x3a/0x100
> [ 24.826576] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
> [ 24.826578] [<ffffffff81636fec>] ret_from_fork+0x7c/0xb0
> [ 24.826580] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
> [ 24.829930] BUG: scheduling while atomic: kworker/u:2/109/0x00000002
> [ 24.836284] 4 locks held by kworker/u:2/109:
> [ 24.836287] #0: ((bond_dev->name)){......}, at:
> [<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
> [ 24.836297] #1: ((&(&bond->mii_work)->work)){......}, at:
> [<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
> [ 24.836304] #2: (rtnl_mutex){......}, at: [<ffffffff81590c00>]
> rtnl_trylock+0x10/0x20
> [ 24.836312] #3: (&bond->lock){......}, at: [<ffffffff8145af55>]
> bond_mii_monitor+0x2d5/0x630
> [ 24.836320] Modules linked in: iptable_filter kvm_intel kvm iTCO_wdt
> acpi_cpufreq mperf button mousedev processor
> [ 24.836334] Pid: 109, comm: kworker/u:2 Tainted: G W
> 3.8.1-Isht-Van #6
> [ 24.836336] Call Trace:
> [ 24.836342] [<ffffffff8162b039>] __schedule_bug+0x5e/0x6c
> [ 24.836348] [<ffffffff816345a2>] __schedule+0x762/0x7f0
> [ 24.836352] [<ffffffff81634744>] schedule+0x24/0x70
> [ 24.836357] [<ffffffff81633704>]
> schedule_hrtimeout_range_clock+0xa4/0x130
> [ 24.836362] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 24.836366] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 24.836371] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
> [ 24.836375] [<ffffffff8163379e>] schedule_hrtimeout_range+0xe/0x10
> [ 24.836380] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
> [ 24.836385] [<ffffffff814b2cbe>] ixgbe_release_swfw_sync_X540+0x4e/0x60
> [ 24.836390] [<ffffffff814aebed>] ixgbe_read_phy_reg_generic+0x10d/0x140
> [ 24.836395] [<ffffffff814aedbc>]
> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
> [ 24.836400] [<ffffffff8145af55>] ? bond_mii_monitor+0x2d5/0x630
> [ 24.836404] [<ffffffff814a64f4>] ixgbe_get_settings+0x34/0x340
> [ 24.836409] [<ffffffff81586ac8>] __ethtool_get_settings+0x88/0x130
> [ 24.836413] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
> [ 24.836418] [<ffffffff8145afc4>] bond_mii_monitor+0x344/0x630
> [ 24.836422] [<ffffffff8105dab1>] process_one_work+0x1a1/0x5d0
> [ 24.836426] [<ffffffff8105da4d>] ? process_one_work+0x13d/0x5d0
> [ 24.836431] [<ffffffff8145ac80>] ? bond_loadbalance_arp_mon+0x300/0x300
> [ 24.836436] [<ffffffff8105ed60>] worker_thread+0x160/0x3f0
> [ 24.836440] [<ffffffff8105ec00>] ? manage_workers+0x290/0x290
> [ 24.836445] [<ffffffff81064446>] kthread+0xd6/0xe0
> [ 24.836449] [<ffffffff8107004a>] ? finish_task_switch+0x3a/0x100
> [ 24.836455] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
> [ 24.836459] [<ffffffff81636fec>] ret_from_fork+0x7c/0xb0
> [ 24.836464] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
> [ 24.839952] bonding: bond0: link status definitely up for interface
> eth_s2_0, 10000 Mbps full duplex.
> [ 24.839968] bonding: bond0: first active interface up!
> [ 24.955598] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow
> Control: Rx/Tx
> [ 25.621770] ixgbe 0000:06:00.1 eth_s2_1: NIC Link is Up 10 Gbps, Flow
> Control: RX/TX
> [ 25.838277] BUG: scheduling while atomic: kworker/u:2/109/0x00000002
> [ 25.844673] 4 locks held by kworker/u:2/109:
> [ 25.844676] #0: ((bond_dev->name)){......}, at:
> [<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
> [ 25.844689] #1: ((&(&bond->mii_work)->work)){......}, at:
> [<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
> [ 25.844705] #2: (rtnl_mutex){......}, at: [<ffffffff81590c00>]
> rtnl_trylock+0x10/0x20
> [ 25.844715] #3: (&bond->lock){......}, at: [<ffffffff8145af55>]
> bond_mii_monitor+0x2d5/0x630
> [ 25.844724] Modules linked in: iptable_filter kvm_intel kvm iTCO_wdt
> acpi_cpufreq mperf button mousedev processor
> [ 25.844740] Pid: 109, comm: kworker/u:2 Tainted: G W
> 3.8.1-Isht-Van #6
> [ 25.844743] Call Trace:
> [ 25.844752] [<ffffffff8162b039>] __schedule_bug+0x5e/0x6c
> [ 25.844759] [<ffffffff816345a2>] __schedule+0x762/0x7f0
> [ 25.844764] [<ffffffff81634744>] schedule+0x24/0x70
> [ 25.844770] [<ffffffff81633704>]
> schedule_hrtimeout_range_clock+0xa4/0x130
> [ 25.844776] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 25.844781] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
> [ 25.844786] [<ffffffff8163379e>] schedule_hrtimeout_range+0xe/0x10
> [ 25.844791] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
> [ 25.844798] [<ffffffff814b2d8c>] ixgbe_acquire_swfw_sync_X540+0xbc/0x100
> [ 25.844805] [<ffffffff814aeb1d>] ixgbe_read_phy_reg_generic+0x3d/0x140
> [ 25.844811] [<ffffffff814aedbc>]
> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
> [ 25.844818] [<ffffffff8145af55>] ? bond_mii_monitor+0x2d5/0x630
> [ 25.844832] [<ffffffff814a64f4>] ixgbe_get_settings+0x34/0x340
> [ 25.844845] [<ffffffff81586ac8>] __ethtool_get_settings+0x88/0x130
> [ 25.844858] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
> [ 25.844866] [<ffffffff8145afc4>] bond_mii_monitor+0x344/0x630
> [ 25.844871] [<ffffffff8105dab1>] process_one_work+0x1a1/0x5d0
> [ 25.844875] [<ffffffff8105da4d>] ? process_one_work+0x13d/0x5d0
> [ 25.844880] [<ffffffff8145ac80>] ? bond_loadbalance_arp_mon+0x300/0x300
> [ 25.844885] [<ffffffff8105ed60>] worker_thread+0x160/0x3f0
> [ 25.844890] [<ffffffff8105ec00>] ? manage_workers+0x290/0x290
> [ 25.844896] [<ffffffff81064446>] kthread+0xd6/0xe0
> [ 25.844901] [<ffffffff8107004a>] ? finish_task_switch+0x3a/0x100
> [ 25.844907] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
> [ 25.844911] [<ffffffff81636fec>] ret_from_fork+0x7c/0xb0
> [ 25.844916] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
> [ 25.848369] BUG: scheduling while atomic: kworker/u:2/109/0x00000002
> [ 25.854761] 4 locks held by kworker/u:2/109:
> [ 25.854764] #0: ((bond_dev->name)){......}, at:
> [<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
> [ 25.854774] #1: ((&(&bond->mii_work)->work)){......}, at:
> [<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
> [ 25.854781] #2: (rtnl_mutex){......}, at: [<ffffffff81590c00>]
> rtnl_trylock+0x10/0x20
> [ 25.854790] #3: (&bond->lock){......}, at: [<ffffffff8145af55>]
> bond_mii_monitor+0x2d5/0x630
> [ 25.854798] Modules linked in: iptable_filter kvm_intel kvm iTCO_wdt
> acpi_cpufreq mperf button mousedev processor
> [ 25.854812] Pid: 109, comm: kworker/u:2 Tainted: G W
> 3.8.1-Isht-Van #6
> [ 25.854814] Call Trace:
> [ 25.854820] [<ffffffff8162b039>] __schedule_bug+0x5e/0x6c
> [ 25.854826] [<ffffffff816345a2>] __schedule+0x762/0x7f0
> [ 25.854831] [<ffffffff81634744>] schedule+0x24/0x70
> [ 25.854835] [<ffffffff81633704>]
> schedule_hrtimeout_range_clock+0xa4/0x130
> [ 25.854840] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 25.854844] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 25.854849] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
> [ 25.854854] [<ffffffff8163379e>] schedule_hrtimeout_range+0xe/0x10
> [ 25.854858] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
> [ 25.854863] [<ffffffff814b2cbe>] ixgbe_release_swfw_sync_X540+0x4e/0x60
> [ 25.854869] [<ffffffff814aebed>] ixgbe_read_phy_reg_generic+0x10d/0x140
> [ 25.854874] [<ffffffff814aedbc>]
> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
> [ 25.854879] [<ffffffff8145af55>] ? bond_mii_monitor+0x2d5/0x630
> [ 25.854883] [<ffffffff814a64f4>] ixgbe_get_settings+0x34/0x340
> [ 25.854888] [<ffffffff81586ac8>] __ethtool_get_settings+0x88/0x130
> [ 25.854892] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
> [ 25.854897] [<ffffffff8145afc4>] bond_mii_monitor+0x344/0x630
> [ 25.854901] [<ffffffff8105dab1>] process_one_work+0x1a1/0x5d0
> [ 25.854905] [<ffffffff8105da4d>] ? process_one_work+0x13d/0x5d0
> [ 25.854910] [<ffffffff8145ac80>] ? bond_loadbalance_arp_mon+0x300/0x300
> [ 25.854915] [<ffffffff8105ed60>] worker_thread+0x160/0x3f0
> [ 25.854920] [<ffffffff8105ec00>] ? manage_workers+0x290/0x290
> [ 25.854925] [<ffffffff81064446>] kthread+0xd6/0xe0
> [ 25.854929] [<ffffffff8107004a>] ? finish_task_switch+0x3a/0x100
> [ 25.854935] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
> [ 25.854939] [<ffffffff81636fec>] ret_from_fork+0x7c/0xb0
> [ 25.854944] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
> [ 25.858392] bonding: bond0: link status definitely up for interface
> eth_s2_1, 10000 Mbps full duplex.
> [ 27.292402] bnx2 0000:01:00.1 eth3: NIC Copper Link is Up, 1000 Mbps
> full duplex
> [ 27.292406] , receive & transmit flow control ON
> [ 28.682172] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow
> Control: Rx/Tx
> [ 29.037441] Status code returned 0xc000005e NT_STATUS_NO_LOGON_SERVERS
> [ 29.037451] CIFS VFS: Send error in SessSetup = -5
> [ 29.043058] CIFS VFS: cifs_mount failed w/return code = -5
> [ 30.005962] Status code returned 0xc000005e NT_STATUS_NO_LOGON_SERVERS
> [ 30.005971] CIFS VFS: Send error in SessSetup = -5
> [ 30.011333] CIFS VFS: cifs_mount failed w/return code = -5
> [ 31.093294] Status code returned 0xc000000d NT_STATUS_INVALID_PARAMETER
> [ 31.093303] CIFS VFS: Send error in SessSetup = -22
> [ 31.098672] CIFS VFS: cifs_mount failed w/return code = -22
> [ 32.339022] device eth0 entered promiscuous mode
> [ 32.523684] device eth1 entered promiscuous mode
> [ 32.739312] device eth2 entered promiscuous mode
> [ 32.922051] device eth3 entered promiscuous mode
> [ 33.075705] device bond0 entered promiscuous mode
> [ 33.075711] device eth_s2_0 entered promiscuous mode
> [ 33.076022] device eth_s2_1 entered promiscuous mode
> [ 34.783087] u32 classifier
> [ 34.783089] Performance counters on
> [ 34.783090] input device check on
> [ 34.783091] Actions configured
> [ 40.834154] bnx2 0000:01:00.0 eth2: NIC Copper Link is Up, 100 Mbps
> full duplex
> [ 40.834158] , receive & transmit flow control ON
>
>
>
On 03/07/2013 03:05 PM, Linda Walsh wrote:
[snip]
> [ 24.820010] BUG: scheduling while atomic: kworker/u:2/109/0x00000002
> [ 24.826415] 4 locks held by kworker/u:2/109:
> [ 24.826425] #0: ((bond_dev->name)){......}, at:
> [<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
> [ 24.826428] #1: ((&(&bond->mii_work)->work)){......}, at:
> [<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
> [ 24.826435] #2: (rtnl_mutex){......}, at: [<ffffffff81590c00>]
> rtnl_trylock+0x10/0x20
> [ 24.826441] #3: (&bond->lock){......}, at: [<ffffffff8145af55>]
> bond_mii_monitor+0x2d5/0x630
> [ 24.826448] Modules linked in: iptable_filter kvm_intel kvm iTCO_wdt
> acpi_cpufreq mperf button mousedev processor
> [ 24.826451] Pid: 109, comm: kworker/u:2 Not tainted 3.8.1-Isht-Van #6
> [ 24.826452] Call Trace:
> [ 24.826459] [<ffffffff8162b039>] __schedule_bug+0x5e/0x6c
> [ 24.826475] [<ffffffff816345a2>] __schedule+0x762/0x7f0
> [ 24.826479] [<ffffffff81634744>] schedule+0x24/0x70
> [ 24.826488] [<ffffffff81633704>]
> schedule_hrtimeout_range_clock+0xa4/0x130
> [ 24.826495] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 24.826499] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
> [ 24.826507] [<ffffffff8163379e>] schedule_hrtimeout_range+0xe/0x10
> [ 24.826512] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
> [ 24.826518] [<ffffffff814b2d8c>] ixgbe_acquire_swfw_sync_X540+0xbc/0x100
> [ 24.826527] [<ffffffff814aeb1d>] ixgbe_read_phy_reg_generic+0x3d/0x140
> [ 24.826532] [<ffffffff814aedbc>]
> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
> [ 24.826537] [<ffffffff8145af55>] ? bond_mii_monitor+0x2d5/0x630
> [ 24.826543] [<ffffffff814a64f4>] ixgbe_get_settings+0x34/0x340
> [ 24.826546] [<ffffffff81586ac8>] __ethtool_get_settings+0x88/0x130
> [ 24.826552] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
> [ 24.826554] [<ffffffff8145afc4>] bond_mii_monitor+0x344/0x630
And both bond_enslave() and bond_mii_monitor() are using bond_update_speed_duplex()
with preempt disabled.
Along with the changes in bond_enslave(), I think you also need this (untested):
diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c
index 11d01d6..9af143a 100644
--- a/drivers/net/bonding/bond_main.c
+++ b/drivers/net/bonding/bond_main.c
@@ -2373,7 +2373,9 @@ static void bond_miimon_commit(struct bonding *bond)
bond_set_backup_slave(slave);
}
+ read_unlock(&bond->lock);
bond_update_speed_duplex(slave);
+ read_lock(&bond->lock);
pr_info("%s: link status definitely up for interface %s, %u Mbps %s duplex.\n",
bond->dev->name, slave->dev->name,
Regards,
Michael Wang
> [ 24.826556] [<ffffffff8105dab1>] process_one_work+0x1a1/0x5d0
> [ 24.826558] [<ffffffff8105da4d>] ? process_one_work+0x13d/0x5d0
> [ 24.826560] [<ffffffff8145ac80>] ? bond_loadbalance_arp_mon+0x300/0x300
> [ 24.826563] [<ffffffff8105ed60>] worker_thread+0x160/0x3f0
> [ 24.826565] [<ffffffff8105ec00>] ? manage_workers+0x290/0x290
> [ 24.826569] [<ffffffff81064446>] kthread+0xd6/0xe0
> [ 24.826573] [<ffffffff8107004a>] ? finish_task_switch+0x3a/0x100
> [ 24.826576] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
> [ 24.826578] [<ffffffff81636fec>] ret_from_fork+0x7c/0xb0
> [ 24.826580] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
> [ 24.829930] BUG: scheduling while atomic: kworker/u:2/109/0x00000002
> [ 24.836284] 4 locks held by kworker/u:2/109:
> [ 24.836287] #0: ((bond_dev->name)){......}, at:
> [<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
> [ 24.836297] #1: ((&(&bond->mii_work)->work)){......}, at:
> [<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
> [ 24.836304] #2: (rtnl_mutex){......}, at: [<ffffffff81590c00>]
> rtnl_trylock+0x10/0x20
> [ 24.836312] #3: (&bond->lock){......}, at: [<ffffffff8145af55>]
> bond_mii_monitor+0x2d5/0x630
> [ 24.836320] Modules linked in: iptable_filter kvm_intel kvm iTCO_wdt
> acpi_cpufreq mperf button mousedev processor
> [ 24.836334] Pid: 109, comm: kworker/u:2 Tainted: G W
> 3.8.1-Isht-Van #6
> [ 24.836336] Call Trace:
> [ 24.836342] [<ffffffff8162b039>] __schedule_bug+0x5e/0x6c
> [ 24.836348] [<ffffffff816345a2>] __schedule+0x762/0x7f0
> [ 24.836352] [<ffffffff81634744>] schedule+0x24/0x70
> [ 24.836357] [<ffffffff81633704>]
> schedule_hrtimeout_range_clock+0xa4/0x130
> [ 24.836362] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 24.836366] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 24.836371] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
> [ 24.836375] [<ffffffff8163379e>] schedule_hrtimeout_range+0xe/0x10
> [ 24.836380] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
> [ 24.836385] [<ffffffff814b2cbe>] ixgbe_release_swfw_sync_X540+0x4e/0x60
> [ 24.836390] [<ffffffff814aebed>] ixgbe_read_phy_reg_generic+0x10d/0x140
> [ 24.836395] [<ffffffff814aedbc>]
> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
> [ 24.836400] [<ffffffff8145af55>] ? bond_mii_monitor+0x2d5/0x630
> [ 24.836404] [<ffffffff814a64f4>] ixgbe_get_settings+0x34/0x340
> [ 24.836409] [<ffffffff81586ac8>] __ethtool_get_settings+0x88/0x130
> [ 24.836413] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
> [ 24.836418] [<ffffffff8145afc4>] bond_mii_monitor+0x344/0x630
> [ 24.836422] [<ffffffff8105dab1>] process_one_work+0x1a1/0x5d0
> [ 24.836426] [<ffffffff8105da4d>] ? process_one_work+0x13d/0x5d0
> [ 24.836431] [<ffffffff8145ac80>] ? bond_loadbalance_arp_mon+0x300/0x300
> [ 24.836436] [<ffffffff8105ed60>] worker_thread+0x160/0x3f0
> [ 24.836440] [<ffffffff8105ec00>] ? manage_workers+0x290/0x290
> [ 24.836445] [<ffffffff81064446>] kthread+0xd6/0xe0
> [ 24.836449] [<ffffffff8107004a>] ? finish_task_switch+0x3a/0x100
> [ 24.836455] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
> [ 24.836459] [<ffffffff81636fec>] ret_from_fork+0x7c/0xb0
> [ 24.836464] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
> [ 24.839952] bonding: bond0: link status definitely up for interface
> eth_s2_0, 10000 Mbps full duplex.
> [ 24.839968] bonding: bond0: first active interface up!
> [ 24.955598] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow
> Control: Rx/Tx
> [ 25.621770] ixgbe 0000:06:00.1 eth_s2_1: NIC Link is Up 10 Gbps, Flow
> Control: RX/TX
> [ 25.838277] BUG: scheduling while atomic: kworker/u:2/109/0x00000002
> [ 25.844673] 4 locks held by kworker/u:2/109:
> [ 25.844676] #0: ((bond_dev->name)){......}, at:
> [<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
> [ 25.844689] #1: ((&(&bond->mii_work)->work)){......}, at:
> [<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
> [ 25.844705] #2: (rtnl_mutex){......}, at: [<ffffffff81590c00>]
> rtnl_trylock+0x10/0x20
> [ 25.844715] #3: (&bond->lock){......}, at: [<ffffffff8145af55>]
> bond_mii_monitor+0x2d5/0x630
> [ 25.844724] Modules linked in: iptable_filter kvm_intel kvm iTCO_wdt
> acpi_cpufreq mperf button mousedev processor
> [ 25.844740] Pid: 109, comm: kworker/u:2 Tainted: G W
> 3.8.1-Isht-Van #6
> [ 25.844743] Call Trace:
> [ 25.844752] [<ffffffff8162b039>] __schedule_bug+0x5e/0x6c
> [ 25.844759] [<ffffffff816345a2>] __schedule+0x762/0x7f0
> [ 25.844764] [<ffffffff81634744>] schedule+0x24/0x70
> [ 25.844770] [<ffffffff81633704>]
> schedule_hrtimeout_range_clock+0xa4/0x130
> [ 25.844776] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 25.844781] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
> [ 25.844786] [<ffffffff8163379e>] schedule_hrtimeout_range+0xe/0x10
> [ 25.844791] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
> [ 25.844798] [<ffffffff814b2d8c>] ixgbe_acquire_swfw_sync_X540+0xbc/0x100
> [ 25.844805] [<ffffffff814aeb1d>] ixgbe_read_phy_reg_generic+0x3d/0x140
> [ 25.844811] [<ffffffff814aedbc>]
> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
> [ 25.844818] [<ffffffff8145af55>] ? bond_mii_monitor+0x2d5/0x630
> [ 25.844832] [<ffffffff814a64f4>] ixgbe_get_settings+0x34/0x340
> [ 25.844845] [<ffffffff81586ac8>] __ethtool_get_settings+0x88/0x130
> [ 25.844858] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
> [ 25.844866] [<ffffffff8145afc4>] bond_mii_monitor+0x344/0x630
> [ 25.844871] [<ffffffff8105dab1>] process_one_work+0x1a1/0x5d0
> [ 25.844875] [<ffffffff8105da4d>] ? process_one_work+0x13d/0x5d0
> [ 25.844880] [<ffffffff8145ac80>] ? bond_loadbalance_arp_mon+0x300/0x300
> [ 25.844885] [<ffffffff8105ed60>] worker_thread+0x160/0x3f0
> [ 25.844890] [<ffffffff8105ec00>] ? manage_workers+0x290/0x290
> [ 25.844896] [<ffffffff81064446>] kthread+0xd6/0xe0
> [ 25.844901] [<ffffffff8107004a>] ? finish_task_switch+0x3a/0x100
> [ 25.844907] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
> [ 25.844911] [<ffffffff81636fec>] ret_from_fork+0x7c/0xb0
> [ 25.844916] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
> [ 25.848369] BUG: scheduling while atomic: kworker/u:2/109/0x00000002
> [ 25.854761] 4 locks held by kworker/u:2/109:
> [ 25.854764] #0: ((bond_dev->name)){......}, at:
> [<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
> [ 25.854774] #1: ((&(&bond->mii_work)->work)){......}, at:
> [<ffffffff8105da4d>] process_one_work+0x13d/0x5d0
> [ 25.854781] #2: (rtnl_mutex){......}, at: [<ffffffff81590c00>]
> rtnl_trylock+0x10/0x20
> [ 25.854790] #3: (&bond->lock){......}, at: [<ffffffff8145af55>]
> bond_mii_monitor+0x2d5/0x630
> [ 25.854798] Modules linked in: iptable_filter kvm_intel kvm iTCO_wdt
> acpi_cpufreq mperf button mousedev processor
> [ 25.854812] Pid: 109, comm: kworker/u:2 Tainted: G W
> 3.8.1-Isht-Van #6
> [ 25.854814] Call Trace:
> [ 25.854820] [<ffffffff8162b039>] __schedule_bug+0x5e/0x6c
> [ 25.854826] [<ffffffff816345a2>] __schedule+0x762/0x7f0
> [ 25.854831] [<ffffffff81634744>] schedule+0x24/0x70
> [ 25.854835] [<ffffffff81633704>]
> schedule_hrtimeout_range_clock+0xa4/0x130
> [ 25.854840] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 25.854844] [<ffffffff81068250>] ? update_rmtp+0x60/0x60
> [ 25.854849] [<ffffffff81068f9f>] ? hrtimer_start_range_ns+0xf/0x20
> [ 25.854854] [<ffffffff8163379e>] schedule_hrtimeout_range+0xe/0x10
> [ 25.854858] [<ffffffff8104ec1b>] usleep_range+0x3b/0x40
> [ 25.854863] [<ffffffff814b2cbe>] ixgbe_release_swfw_sync_X540+0x4e/0x60
> [ 25.854869] [<ffffffff814aebed>] ixgbe_read_phy_reg_generic+0x10d/0x140
> [ 25.854874] [<ffffffff814aedbc>]
> ixgbe_get_copper_link_capabilities_generic+0x2c/0x60
> [ 25.854879] [<ffffffff8145af55>] ? bond_mii_monitor+0x2d5/0x630
> [ 25.854883] [<ffffffff814a64f4>] ixgbe_get_settings+0x34/0x340
> [ 25.854888] [<ffffffff81586ac8>] __ethtool_get_settings+0x88/0x130
> [ 25.854892] [<ffffffff814568a3>] bond_update_speed_duplex+0x23/0x60
> [ 25.854897] [<ffffffff8145afc4>] bond_mii_monitor+0x344/0x630
> [ 25.854901] [<ffffffff8105dab1>] process_one_work+0x1a1/0x5d0
> [ 25.854905] [<ffffffff8105da4d>] ? process_one_work+0x13d/0x5d0
> [ 25.854910] [<ffffffff8145ac80>] ? bond_loadbalance_arp_mon+0x300/0x300
> [ 25.854915] [<ffffffff8105ed60>] worker_thread+0x160/0x3f0
> [ 25.854920] [<ffffffff8105ec00>] ? manage_workers+0x290/0x290
> [ 25.854925] [<ffffffff81064446>] kthread+0xd6/0xe0
> [ 25.854929] [<ffffffff8107004a>] ? finish_task_switch+0x3a/0x100
> [ 25.854935] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
> [ 25.854939] [<ffffffff81636fec>] ret_from_fork+0x7c/0xb0
> [ 25.854944] [<ffffffff81064370>] ? flush_kthread_worker+0x160/0x160
> [ 25.858392] bonding: bond0: link status definitely up for interface
> eth_s2_1, 10000 Mbps full duplex.
> [ 27.292402] bnx2 0000:01:00.1 eth3: NIC Copper Link is Up, 1000 Mbps
> full duplex
> [ 27.292406] , receive & transmit flow control ON
> [ 28.682172] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow
> Control: Rx/Tx
> [ 29.037441] Status code returned 0xc000005e NT_STATUS_NO_LOGON_SERVERS
> [ 29.037451] CIFS VFS: Send error in SessSetup = -5
> [ 29.043058] CIFS VFS: cifs_mount failed w/return code = -5
> [ 30.005962] Status code returned 0xc000005e NT_STATUS_NO_LOGON_SERVERS
> [ 30.005971] CIFS VFS: Send error in SessSetup = -5
> [ 30.011333] CIFS VFS: cifs_mount failed w/return code = -5
> [ 31.093294] Status code returned 0xc000000d NT_STATUS_INVALID_PARAMETER
> [ 31.093303] CIFS VFS: Send error in SessSetup = -22
> [ 31.098672] CIFS VFS: cifs_mount failed w/return code = -22
> [ 32.339022] device eth0 entered promiscuous mode
> [ 32.523684] device eth1 entered promiscuous mode
> [ 32.739312] device eth2 entered promiscuous mode
> [ 32.922051] device eth3 entered promiscuous mode
> [ 33.075705] device bond0 entered promiscuous mode
> [ 33.075711] device eth_s2_0 entered promiscuous mode
> [ 33.076022] device eth_s2_1 entered promiscuous mode
> [ 34.783087] u32 classifier
> [ 34.783089] Performance counters on
> [ 34.783090] input device check on
> [ 34.783091] Actions configured
> [ 40.834154] bnx2 0000:01:00.0 eth2: NIC Copper Link is Up, 100 Mbps
> full duplex
> [ 40.834158] , receive & transmit flow control ON
>
>
>
On 03/07/2013 04:50 PM, Linda Walsh wrote:
>
> I am *not* seeing the bug in 3.8.2 with the 2nd patch applied (in
> addition to the first)...
So that means bond lock is the reason, nice, but this is really not a
good fix if we just unlock it...
The better way is to move the cycle wait logical out of the
bond_update_speed_duplex() IMO, I think we need the folk who work on
this driver to make the decision ;-)
Regards,
Michael Wang
>
>
> Michael Wang wrote:
>>
>>
>> And both bond_enslave() and bond_mii_monitor() are using bond_update_speed_duplex()
>> with preempt disabled.
>>
>> Along with the changes in bond_enslave(), I think you also need this (untested):
>>
>> diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c
>> index 11d01d6..9af143a 100644
>> --- a/drivers/net/bonding/bond_main.c
>> +++ b/drivers/net/bonding/bond_main.c
>> @@ -2373,7 +2373,9 @@ static void bond_miimon_commit(struct bonding *bond)
>> bond_set_backup_slave(slave);
>> }
>>
>> + read_unlock(&bond->lock);
>> bond_update_speed_duplex(slave);
>> + read_lock(&bond->lock);
>>
>> pr_info("%s: link status definitely up for interface %s, %u Mbps %s duplex.\n",
>> bond->dev->name, slave->dev->name,
>>
>>
>> Regards,
>> Michael Wang
>>
>>
>>
>
On Thu, Mar 7, 2013 at 10:50 AM, Michael Wang
<[email protected]> wrote:
> On 03/07/2013 04:50 PM, Linda Walsh wrote:
>>
>> I am *not* seeing the bug in 3.8.2 with the 2nd patch applied (in
>> addition to the first)...
>
> So that means bond lock is the reason, nice, but this is really not a
> good fix if we just unlock it...
You're right, we can't unlock bond->lock while in bond_for_each_slave(),
however I think we don't even need that bond_update_speed_duplex() in
bond_miimon_commit() - cause the speed/duplex on interface state change
were already updated via NETDEV_UP/CHANGE event in
bond_slave_netdev_event() - and if not, it's not our fault, but the
driver's that he didn't call the notifiers.
So, maybe something like this would work (any feedback welcome, it's
definitely not the first time we hit the wall with sleeping in
bond_update_speed_duplex):
Subject: [PATCH] bonding: don't call update_speed_duplex() under spinlocks
bond_update_speed_duplex() might sleep while calling underlying slave's
routines. Move it out of atomic context in bond_enslave() and remove it
from bond_miimon_commit() - it was introduced by commit 546add79, however
when the slave interfaces go up/change state it's their responsability to
fire NETDEV_UP/NETDEV_CHANGE events so that bonding can properly update
their speed.
---
drivers/net/bonding/bond_main.c | 6 ++----
1 files changed, 2 insertions(+), 4 deletions(-)
diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c
index 7bd068a..c63a33c 100644
--- a/drivers/net/bonding/bond_main.c
+++ b/drivers/net/bonding/bond_main.c
@@ -1746,6 +1746,8 @@ int bond_enslave(struct net_device *bond_dev,
struct net_device *slave_dev)
bond_compute_features(bond);
+ bond_update_speed_duplex(new_slave);
+
read_lock(&bond->lock);
new_slave->last_arp_rx = jiffies -
@@ -1798,8 +1800,6 @@ int bond_enslave(struct net_device *bond_dev,
struct net_device *slave_dev)
new_slave->link == BOND_LINK_DOWN ? "DOWN" :
(new_slave->link == BOND_LINK_UP ? "UP" : "BACK"));
- bond_update_speed_duplex(new_slave);
-
if (USES_PRIMARY(bond->params.mode) && bond->params.primary[0]) {
/* if there is a primary slave, remember it */
if (strcmp(bond->params.primary, new_slave->dev->name) == 0) {
@@ -2373,8 +2373,6 @@ static void bond_miimon_commit(struct bonding *bond)
bond_set_backup_slave(slave);
}
- bond_update_speed_duplex(slave);
-
pr_info("%s: link status definitely up for interface %s, %u Mbps
%s duplex.\n",
bond->dev->name, slave->dev->name,
slave->speed, slave->duplex ? "full" : "half");
--
1.7.1
>
> The better way is to move the cycle wait logical out of the
> bond_update_speed_duplex() IMO, I think we need the folk who work on
> this driver to make the decision ;-)
>
> Regards,
> Michael Wang
>
>>
>>
>> Michael Wang wrote:
>>>
>>>
>>> And both bond_enslave() and bond_mii_monitor() are using bond_update_speed_duplex()
>>> with preempt disabled.
>>>
>>> Along with the changes in bond_enslave(), I think you also need this (untested):
>>>
>>> diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c
>>> index 11d01d6..9af143a 100644
>>> --- a/drivers/net/bonding/bond_main.c
>>> +++ b/drivers/net/bonding/bond_main.c
>>> @@ -2373,7 +2373,9 @@ static void bond_miimon_commit(struct bonding *bond)
>>> bond_set_backup_slave(slave);
>>> }
>>>
>>> + read_unlock(&bond->lock);
>>> bond_update_speed_duplex(slave);
>>> + read_lock(&bond->lock);
>>>
>>> pr_info("%s: link status definitely up for interface %s, %u Mbps %s duplex.\n",
>>> bond->dev->name, slave->dev->name,
>>>
>>>
>>> Regards,
>>> Michael Wang
>>>
>>>
>>>
>>
>
> --
> To unsubscribe from this list: send the line "unsubscribe netdev" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
Best regards,
Veaceslav Falico