This patch series adds the relevant phy and controller
configurations for enabling USB2 on IPQ5332
v6:
Binding and dts:-
Dropped the qcom,dwc3.yaml patch as it has been picked up for linux-next
Add const to compatible, vdd-supply
Move nodes per register address
Driver:-
Add vdd-supply
Cleanup error paths in probe with dev_err_probe
v5:
Binding and dts:-
Fix email id
Removed 'Reviewed-by: Krzysztof Kozlowski <[email protected]>'
as had to change bindings file to be able to use generic phy instead of
usb-phy
Driver:-
Remove unused definition
Use generic phy instead of usb-phy
v4:
Binding and dts:-
Change node name (bindings & dts)
Driver:-
Remove unused enum
static const for '.data'
Error handling for devm_clk_get
v3:
Fix bindings file based on review comments
v1:
Cleanup DTS
Combine driver, kconfig and makefile patches
Remove unused functions from M31 driver
Drop the clock driver changes
Varadarajan Narayanan (5):
dt-bindings: phy: qcom,m31: Document qcom,m31 USB phy
phy: qcom-m31: Introduce qcom,m31 USB phy driver
arm64: dts: qcom: ipq5332: Add USB related nodes
arm64: dts: qcom: ipq5332: Enable USB
arm64: defconfig: Enable M31 USB phy driver
.../bindings/phy/qcom,ipq5332-usb-hsphy.yaml | 59 +++++
arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts | 23 ++
arch/arm64/boot/dts/qcom/ipq5332.dtsi | 55 +++++
arch/arm64/configs/defconfig | 1 +
drivers/phy/qualcomm/Kconfig | 11 +
drivers/phy/qualcomm/Makefile | 1 +
drivers/phy/qualcomm/phy-qcom-m31.c | 248 +++++++++++++++++++++
7 files changed, 398 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom,ipq5332-usb-hsphy.yaml
create mode 100644 drivers/phy/qualcomm/phy-qcom-m31.c
--
2.7.4
Enable M31 USB phy driver present in IPQ5332.
Signed-off-by: Varadarajan Narayanan <[email protected]>
---
v2:
Add full stop to commit log.
---
arch/arm64/configs/defconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 6cbf6eb..e6d2012 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -1389,6 +1389,7 @@ CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2=m
CONFIG_PHY_QCOM_USB_HS_28NM=m
CONFIG_PHY_QCOM_USB_SS=m
CONFIG_PHY_QCOM_SGMII_ETH=m
+CONFIG_PHY_QCOM_M31_USB=m
CONFIG_PHY_R8A779F0_ETHERNET_SERDES=y
CONFIG_PHY_RCAR_GEN3_PCIE=y
CONFIG_PHY_RCAR_GEN3_USB2=y
--
2.7.4
Add the M31 USB2 phy driver.
Signed-off-by: Varadarajan Narayanan <[email protected]>
---
v6:
Kconfig:Add COMPILE_TEST and remove USB_GADGET from 'depends'
Change 'selects' USB_PHY -> GENERIC_PHY
Driver: Use correct headers
const int -> unsigned int for 'nregs' in private data
Use generic names for clk, phy in m31 phy structure
Init register details directly instead of using macro
Use dev_err_probe in the error paths of driver probe
v5:
Kconfig and Makefile:- place snippet according to sorted order
Use generic phy instead of usb-phy
Use ARRAY_SIZE for reg init instead of blank last entry
Fix copyright year
v4:
Remove unused enum
Error handling for devm_clk_get
v1:
Combine driver, makefile and kconfig into 1 patch
Remove 'qscratch' region and its usage. The controller driver takes care
of those settings
Use compatible/data to handle ipq5332 init
Drop the default case
Get resources by index instead of name as there is only one resource
Add clock
Fix review comments in the driver
---
drivers/phy/qualcomm/Kconfig | 11 ++
drivers/phy/qualcomm/Makefile | 1 +
drivers/phy/qualcomm/phy-qcom-m31.c | 248 ++++++++++++++++++++++++++++++++++++
3 files changed, 260 insertions(+)
create mode 100644 drivers/phy/qualcomm/phy-qcom-m31.c
diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
index ced6038..d891058 100644
--- a/drivers/phy/qualcomm/Kconfig
+++ b/drivers/phy/qualcomm/Kconfig
@@ -143,6 +143,17 @@ config PHY_QCOM_EUSB2_REPEATER
PMICs. The repeater is paired with a Synopsys eUSB2 Phy
on Qualcomm SOCs.
+config PHY_QCOM_M31_USB
+ tristate "Qualcomm M31 HS PHY driver support"
+ depends on USB && (ARCH_QCOM || COMPILE_TEST)
+ select GENERIC_PHY
+ help
+ Enable this to support M31 HS PHY transceivers on Qualcomm chips
+ with DWC3 USB core. It handles PHY initialization, clock
+ management required after resetting the hardware and power
+ management. This driver is required even for peripheral only or
+ host only mode configurations.
+
config PHY_QCOM_USB_HS
tristate "Qualcomm USB HS PHY module"
depends on USB_ULPI_BUS
diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
index df94581..ffd609a 100644
--- a/drivers/phy/qualcomm/Makefile
+++ b/drivers/phy/qualcomm/Makefile
@@ -4,6 +4,7 @@ obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o
obj-$(CONFIG_PHY_QCOM_EDP) += phy-qcom-edp.o
obj-$(CONFIG_PHY_QCOM_IPQ4019_USB) += phy-qcom-ipq4019-usb.o
obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
+obj-$(CONFIG_PHY_QCOM_M31_USB) += phy-qcom-m31.o
obj-$(CONFIG_PHY_QCOM_PCIE2) += phy-qcom-pcie2.o
obj-$(CONFIG_PHY_QCOM_QMP_COMBO) += phy-qcom-qmp-combo.o
diff --git a/drivers/phy/qualcomm/phy-qcom-m31.c b/drivers/phy/qualcomm/phy-qcom-m31.c
new file mode 100644
index 0000000..d6a8d06
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-m31.c
@@ -0,0 +1,248 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2014-2023, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+#define USB2PHY_PORT_UTMI_CTRL1 0x40
+
+#define USB2PHY_PORT_UTMI_CTRL2 0x44
+ #define UTMI_ULPI_SEL BIT(7)
+ #define UTMI_TEST_MUX_SEL BIT(6)
+
+#define HS_PHY_CTRL_REG 0x10
+ #define UTMI_OTG_VBUS_VALID BIT(20)
+ #define SW_SESSVLD_SEL BIT(28)
+
+#define USB_PHY_UTMI_CTRL0 0x3c
+
+#define USB_PHY_UTMI_CTRL5 0x50
+ #define POR_EN BIT(1)
+
+#define USB_PHY_HS_PHY_CTRL_COMMON0 0x54
+ #define COMMONONN BIT(7)
+ #define FSEL BIT(4)
+ #define RETENABLEN BIT(3)
+ #define FREQ_24MHZ (GENMASK(6, 6) | GENMASK(4, 4))
+
+#define USB_PHY_HS_PHY_CTRL2 0x64
+ #define USB2_SUSPEND_N_SEL BIT(3)
+ #define USB2_SUSPEND_N BIT(2)
+ #define USB2_UTMI_CLK_EN BIT(1)
+
+#define USB_PHY_CFG0 0x94
+ #define UTMI_PHY_OVERRIDE_EN BIT(1)
+
+#define USB_PHY_REFCLK_CTRL 0xa0
+ #define CLKCORE BIT(1)
+
+#define USB2PHY_PORT_POWERDOWN 0xa4
+ #define POWER_UP BIT(0)
+ #define POWER_DOWN 0
+
+#define USB_PHY_FSEL_SEL 0xb8
+ #define FREQ_SEL BIT(0)
+
+#define USB2PHY_USB_PHY_M31_XCFGI_1 0xbc
+ #define USB2_0_TX_ENABLE BIT(2)
+
+#define USB2PHY_USB_PHY_M31_XCFGI_4 0xc8
+ #define HSTX_SLEW_RATE_565PS GENMASK(1, 0)
+ #define PLL_CHARGING_PUMP_CURRENT_35UA GENMASK(4, 3)
+ #define ODT_VALUE_38_02_OHM GENMASK(7, 6)
+
+#define USB2PHY_USB_PHY_M31_XCFGI_5 0xcc
+ #define ODT_VALUE_45_02_OHM BIT(2)
+ #define HSTX_PRE_EMPHASIS_LEVEL_0_55MA BIT(0)
+
+#define USB2PHY_USB_PHY_M31_XCFGI_11 0xe4
+ #define XCFG_COARSE_TUNE_NUM BIT(1)
+ #define XCFG_FINE_TUNE_NUM BIT(3)
+
+struct m31_phy_regs {
+ u32 off;
+ u32 val;
+ u32 delay;
+};
+
+struct m31_priv_data {
+ bool ulpi_mode;
+ const struct m31_phy_regs *regs;
+ unsigned int nregs;
+};
+
+struct m31_phy_regs m31_ipq5332_regs[] = {
+ { USB_PHY_CFG0, UTMI_PHY_OVERRIDE_EN, 0 },
+ { USB_PHY_UTMI_CTRL5, POR_EN, 15 },
+ { USB_PHY_FSEL_SEL, FREQ_SEL, 0 },
+ { USB_PHY_HS_PHY_CTRL_COMMON0, COMMONONN | FREQ_24MHZ | RETENABLEN, 0 },
+ { USB_PHY_UTMI_CTRL5, POR_EN, 0 },
+ { USB_PHY_HS_PHY_CTRL2, USB2_SUSPEND_N_SEL | USB2_SUSPEND_N | USB2_UTMI_CLK_EN, 0 },
+ { USB2PHY_USB_PHY_M31_XCFGI_11, XCFG_COARSE_TUNE_NUM | XCFG_FINE_TUNE_NUM, 0 },
+ { USB2PHY_USB_PHY_M31_XCFGI_4, HSTX_SLEW_RATE_565PS | PLL_CHARGING_PUMP_CURRENT_35UA |
+ ODT_VALUE_38_02_OHM, 0 },
+ { USB2PHY_USB_PHY_M31_XCFGI_1, USB2_0_TX_ENABLE, 0 },
+ { USB2PHY_USB_PHY_M31_XCFGI_5, ODT_VALUE_45_02_OHM | HSTX_PRE_EMPHASIS_LEVEL_0_55MA, 4 },
+ { USB_PHY_UTMI_CTRL5, 0x0, 0 },
+ { USB_PHY_HS_PHY_CTRL2, USB2_SUSPEND_N | USB2_UTMI_CLK_EN, 0 },
+};
+
+struct m31usb_phy {
+ struct phy *phy;
+ void __iomem *base;
+ const struct m31_phy_regs *regs;
+ int nregs;
+
+ struct regulator *vreg;
+ struct clk *clk;
+ struct reset_control *reset;
+
+ bool ulpi_mode;
+};
+
+static int m31usb_phy_init(struct phy *phy)
+{
+ struct m31usb_phy *qphy = phy_get_drvdata(phy);
+ const struct m31_phy_regs *regs = qphy->regs;
+ int i, ret;
+
+ ret = regulator_enable(qphy->vreg);
+ if (ret) {
+ dev_err(&phy->dev, "failed to enable regulator, %d\n", ret);
+ return ret;
+ }
+
+ ret = clk_prepare_enable(qphy->clk);
+ if (ret) {
+ if (qphy->vreg)
+ regulator_disable(qphy->vreg);
+ dev_err(&phy->dev, "failed to enable cfg ahb clock, %d\n", ret);
+ return ret;
+ }
+
+ /* Perform phy reset */
+ reset_control_assert(qphy->reset);
+ udelay(5);
+ reset_control_deassert(qphy->reset);
+
+ /* configure for ULPI mode if requested */
+ if (qphy->ulpi_mode)
+ writel(0x0, qphy->base + USB2PHY_PORT_UTMI_CTRL2);
+
+ /* Enable the PHY */
+ writel(POWER_UP, qphy->base + USB2PHY_PORT_POWERDOWN);
+
+ /* Turn on phy ref clock */
+ for (i = 0; i < qphy->nregs; i++) {
+ writel(regs[i].val, qphy->base + regs[i].off);
+ if (regs[i].delay)
+ udelay(regs[i].delay);
+ }
+
+ return 0;
+}
+
+static int m31usb_phy_shutdown(struct phy *phy)
+{
+ struct m31usb_phy *qphy = phy_get_drvdata(phy);
+
+ /* Disable the PHY */
+ writel_relaxed(POWER_DOWN, qphy->base + USB2PHY_PORT_POWERDOWN);
+
+ clk_disable_unprepare(qphy->clk);
+
+ regulator_disable(qphy->vreg);
+
+ return 0;
+}
+
+static const struct phy_ops m31usb_phy_gen_ops = {
+ .power_on = m31usb_phy_init,
+ .power_off = m31usb_phy_shutdown,
+ .owner = THIS_MODULE,
+};
+
+static int m31usb_phy_probe(struct platform_device *pdev)
+{
+ struct phy_provider *phy_provider;
+ const struct m31_priv_data *data;
+ struct device *dev = &pdev->dev;
+ struct m31usb_phy *qphy;
+
+ qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL);
+ if (!qphy)
+ return -ENOMEM;
+
+ qphy->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(qphy->base))
+ return PTR_ERR(qphy->base);
+
+ qphy->reset = devm_reset_control_get_exclusive_by_index(dev, 0);
+ if (IS_ERR(qphy->reset))
+ return PTR_ERR(qphy->reset);
+
+ qphy->clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(qphy->clk))
+ return dev_err_probe(dev, PTR_ERR(qphy->clk),
+ "failed to get clk\n");
+
+ data = of_device_get_match_data(dev);
+ qphy->regs = data->regs;
+ qphy->nregs = data->nregs;
+ qphy->ulpi_mode = data->ulpi_mode;
+
+ qphy->phy = devm_phy_create(dev, NULL, &m31usb_phy_gen_ops);
+ if (IS_ERR(qphy->phy))
+ return dev_err_probe(dev, PTR_ERR(qphy->phy),
+ "failed to create phy\n");
+
+ qphy->vreg = devm_regulator_get(dev, "vdda-phy");
+ if (IS_ERR(qphy->vreg))
+ return dev_err_probe(dev, PTR_ERR(qphy->phy),
+ "failed to get vreg\n");
+
+ phy_set_drvdata(qphy->phy, qphy);
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (!IS_ERR(phy_provider))
+ dev_info(dev, "Registered M31 USB phy\n");
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct m31_priv_data m31_ipq5332_data = {
+ .ulpi_mode = false,
+ .regs = m31_ipq5332_regs,
+ .nregs = ARRAY_SIZE(m31_ipq5332_regs),
+};
+
+static const struct of_device_id m31usb_phy_id_table[] = {
+ { .compatible = "qcom,ipq5332-usb-hsphy", .data = &m31_ipq5332_data },
+ { },
+};
+MODULE_DEVICE_TABLE(of, m31usb_phy_id_table);
+
+static struct platform_driver m31usb_phy_driver = {
+ .probe = m31usb_phy_probe,
+ .driver = {
+ .name = "qcom-m31usb-phy",
+ .of_match_table = m31usb_phy_id_table,
+ },
+};
+
+module_platform_driver(m31usb_phy_driver);
+
+MODULE_DESCRIPTION("USB2 Qualcomm M31 HSPHY driver");
+MODULE_LICENSE("GPL");
--
2.7.4
Enable USB2 in host mode.
Signed-off-by: Varadarajan Narayanan <[email protected]>
---
v6:
Add vdd-supply and corresponding regulator
v1:
Enable usb-phy node
---
arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts | 23 +++++++++++++++++++++++
1 file changed, 23 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts b/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
index f96b0c8..b4099a2f 100644
--- a/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
+++ b/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
@@ -12,6 +12,15 @@
/ {
model = "Qualcomm Technologies, Inc. IPQ5332 MI01.6";
compatible = "qcom,ipq5332-ap-mi01.6", "qcom,ipq5332";
+
+ regulator_fixed_5p0: s0500 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <500000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-name = "fixed_5p0";
+ };
};
&blsp1_spi0 {
@@ -79,3 +88,17 @@
bias-pull-up;
};
};
+
+&usbphy0 {
+ vdd-supply = <®ulator_fixed_5p0>;
+
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb2_0_dwc {
+ dr_mode = "host";
+};
--
2.7.4
Document the M31 USB2 phy present in IPQ5332.
Co-developed-by: Sricharan Ramabadhran <[email protected]>
Signed-off-by: Sricharan Ramabadhran <[email protected]>
Signed-off-by: Varadarajan Narayanan <[email protected]>
---
v6:
Add 'Co-developed-by: Sricharan'
Add 'const' to compatible, vdd-supply
Remove label and use usb2-phy for nodename in the example
v5:
Add '#phy-cells', to be able to use generic phy
Remove 'Reviewed-by: Krzysztof Kozlowski' due to above change
v4:
Move M31 URL to description
Remove maxItems and relevant content from clock-names
Change node name to generic name
'make dt_binding_check DT_SCHEMA_FILES=qcom' passed
v3:
Incorporate review comments. Will bring in ipq5018 compatible
string while posting ipq5018 usb patchset.
v1:
Rename qcom,m31.yaml -> qcom,ipq5332-usb-hsphy.yaml
Drop default binding "m31,usb-hsphy"
Add clock
Remove 'oneOf' from compatible
Remove 'qscratch' region from register space as it is not needed
Remove reset-names
Fix the example definition
---
.../bindings/phy/qcom,ipq5332-usb-hsphy.yaml | 59 ++++++++++++++++++++++
1 file changed, 59 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom,ipq5332-usb-hsphy.yaml
diff --git a/Documentation/devicetree/bindings/phy/qcom,ipq5332-usb-hsphy.yaml b/Documentation/devicetree/bindings/phy/qcom,ipq5332-usb-hsphy.yaml
new file mode 100644
index 0000000..97ad905
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,ipq5332-usb-hsphy.yaml
@@ -0,0 +1,59 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/qcom,ipq5332-usb-hsphy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: M31 USB PHY
+
+maintainers:
+ - Sricharan Ramabadhran <[email protected]>
+ - Varadarajan Narayanan <[email protected]>
+
+description:
+ USB M31 PHY (https://www.m31tech.com) found in Qualcomm
+ IPQ5018, IPQ5332 SoCs.
+
+properties:
+ "#phy-cells":
+ const: 0
+
+ compatible:
+ items:
+ - const: qcom,ipq5332-usb-hsphy
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ items:
+ - const: cfg_ahb
+
+ resets:
+ maxItems: 1
+
+ vdd-supply:
+ description:
+ Phandle to 5V regulator supply to PHY digital circuit.
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,ipq5332-gcc.h>
+ usb2-phy@7b000 {
+ compatible = "qcom,ipq5332-usb-hsphy";
+ reg = <0x0007b000 0x12c>;
+
+ clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>;
+ clock-names = "cfg_ahb";
+
+ #phy-cells = <0>;
+
+ resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
+
+ vdd-supply = <®ulator_fixed_5p0>;
+ };
--
2.7.4
On 27/07/2023 08:33, Varadarajan Narayanan wrote:
> Document the M31 USB2 phy present in IPQ5332.
>
> Co-developed-by: Sricharan Ramabadhran <[email protected]>
> Signed-off-by: Sricharan Ramabadhran <[email protected]>
> Signed-off-by: Varadarajan Narayanan <[email protected]>
> ---
> +properties:
> + "#phy-cells":
> + const: 0
> +
> + compatible:
> + items:
> + - const: qcom,ipq5332-usb-hsphy
Please keep compatible as first property.
> +
> + reg:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 1
> +
> + clock-names:
> + items:
> + - const: cfg_ahb
> +
> + resets:
> + maxItems: 1
> +
> + vdd-supply:
> + description:
> + Phandle to 5V regulator supply to PHY digital circuit.
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/qcom,ipq5332-gcc.h>
> + usb2-phy@7b000 {
This was actually better before as usb-phy, I don't know why did you
changed. Especially that you already changed once to usb-phy and this
got review tag. It's fine. If there is going to be resubmit then fix
these two issues.
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Best regards,
Krzysztof
On Thu, Jul 27, 2023 at 08:47:07AM +0200, Krzysztof Kozlowski wrote:
> On 27/07/2023 08:33, Varadarajan Narayanan wrote:
> > Document the M31 USB2 phy present in IPQ5332.
> >
> > Co-developed-by: Sricharan Ramabadhran <[email protected]>
> > Signed-off-by: Sricharan Ramabadhran <[email protected]>
> > Signed-off-by: Varadarajan Narayanan <[email protected]>
> > ---
>
>
> > +properties:
> > + "#phy-cells":
> > + const: 0
> > +
> > + compatible:
> > + items:
> > + - const: qcom,ipq5332-usb-hsphy
>
> Please keep compatible as first property.
>
> > +
> > + reg:
> > + maxItems: 1
> > +
> > + clocks:
> > + maxItems: 1
> > +
> > + clock-names:
> > + items:
> > + - const: cfg_ahb
> > +
> > + resets:
> > + maxItems: 1
> > +
> > + vdd-supply:
> > + description:
> > + Phandle to 5V regulator supply to PHY digital circuit.
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > + - |
> > + #include <dt-bindings/clock/qcom,ipq5332-gcc.h>
> > + usb2-phy@7b000 {
>
> This was actually better before as usb-phy, I don't know why did you
> changed. Especially that you already changed once to usb-phy and this
> got review tag. It's fine. If there is going to be resubmit then fix
> these two issues.
Based on Bjorn's and Rob's comments (https://lore.kernel.org/linux-arm-msm/[email protected]/)
I assumed they preferred usb2-phy and hence changed. Will revert
back to usb-phy if I post another version.
> Reviewed-by: Krzysztof Kozlowski <[email protected]>
Thanks
Varada