Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
The new driver uses the generic PHY framework and will interact
with DWC3 controller present on Exynos5 series of SoCs.
Thereby, removing old phy-samsung-usb3 driver and related code
used untill now which was based on usb/phy framework.
Signed-off-by: Vivek Gautam <[email protected]>
---
Changes from v2:
1) Added support for multiple PHYs (UTMI+ and PIPE3) and
related changes in the driver structuring.
2) Added a xlate function to get the required phy out of
number of PHYs in mutiple PHY scenerio.
3) Changed the names of few structures and variables to
have a clearer meaning.
4) Added 'usb3phy_config' structure to take care of mutiple
phys for a SoC having 'exynos5_usb3phy_drv_data' driver data.
5) Not deleting support for old driver 'phy-samsung-usb3' until
required support for generic phy is added to DWC3.
.../devicetree/bindings/phy/samsung-phy.txt | 49 ++
drivers/phy/Kconfig | 8 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-exynos5-usb3.c | 621 ++++++++++++++++++++
4 files changed, 679 insertions(+)
create mode 100644 drivers/phy/phy-exynos5-usb3.c
diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt
index c0fccaa..57079f8 100644
--- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
+++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
@@ -20,3 +20,52 @@ Required properties:
- compatible : should be "samsung,exynos5250-dp-video-phy";
- reg : offset and length of the Display Port PHY register set;
- #phy-cells : from the generic PHY bindings, must be 0;
+
+Samsung Exynos5 SoC series USB 3.0 PHY controller
+--------------------------------------------------
+
+Required properties:
+- compatible : Should be set to one of the following supported values:
+ - "samsung,exynos5250-usb3phy" - for exynos5250 SoC,
+ - "samsung,exynos5420-usb3phy" - for exynos5420 SoC.
+- reg : Register offset and length of USB 3.0 PHY register set;
+- clocks: Clock IDs array as required by the controller
+- clock-names: names of clocks correseponding to IDs in the clock property;
+ Required clocks:
+ - phy: main PHY clock (same as USB 3.0 controller IP clock),
+ used for register access.
+ - usb3phy_refclk: PHY's reference clock (usually crystal clock),
+ associated by phy name, used to determine bit values for
+ clock settings register.
+ Additional clock required for Exynos5420:
+ - usb30_sclk_100m: Additional special clock used for PHY operation
+ depicted as 'sclk_usbphy30' in CMU of Exynos5420.
+- samsung,syscon-phandle: phandle for syscon interface, which is used to
+ control pmu registers for power isolation.
+- #phy-cells : from the generic PHY bindings, must be 1;
+
+For "samsung,exynos5250-usb3phy" and "samsung,exynos5420-usb3phy" compatible
+PHYs, the second cell in the PHY specifier identifies the PHY id, which is
+interpreted as follows:
+ 0 - UTMI+ type phy,
+ 1 - PIPE3 type phy,
+
+Example:
+ usb3_phy: usbphy@12100000 {
+ compatible = "samsung,exynos5250-usb3phy";
+ reg = <0x12100000 0x100>;
+ clocks = <&clock 286>, <&clock 1>;
+ clock-names = "phy", "usb3phy_refclk";
+ samsung,syscon-phandle = <&pmu_syscon>;
+ #phy-cells = <1>;
+ };
+
+- aliases: For SoCs like Exynos5420 having multiple USB PHY controllers,
+ 'usb3_phy' nodes should have numbered alias in the aliases node,
+ in the form of usb3phyN, N = 0, 1... (depending on number of
+ controllers).
+Example:
+ aliases {
+ usb3phy0 = &usb3_phy0;
+ usb3phy1 = &usb3_phy1;
+ };
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 330ef2d..32f9f38 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -51,4 +51,12 @@ config PHY_EXYNOS_DP_VIDEO
help
Support for Display Port PHY found on Samsung EXYNOS SoCs.
+config PHY_EXYNOS5_USB3
+ tristate "Exynos5 SoC series USB 3.0 PHY driver"
+ depends on ARCH_EXYNOS5
+ select GENERIC_PHY
+ select MFD_SYSCON
+ help
+ Enable USB 3.0 PHY support for Exynos 5 SoC series
+
endmenu
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index d0caae9..9c06a61 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -7,3 +7,4 @@ obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) += phy-exynos-dp-video.o
obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
+obj-$(CONFIG_PHY_EXYNOS5_USB3) += phy-exynos5-usb3.o
diff --git a/drivers/phy/phy-exynos5-usb3.c b/drivers/phy/phy-exynos5-usb3.c
new file mode 100644
index 0000000..24efed0
--- /dev/null
+++ b/drivers/phy/phy-exynos5-usb3.c
@@ -0,0 +1,621 @@
+/*
+ * Samsung EXYNOS5 SoC series USB 3.0 PHY driver
+ *
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Author: Vivek Gautam <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/mutex.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+
+/* Exynos USB PHY registers */
+#define EXYNOS5_FSEL_9MHZ6 0x0
+#define EXYNOS5_FSEL_10MHZ 0x1
+#define EXYNOS5_FSEL_12MHZ 0x2
+#define EXYNOS5_FSEL_19MHZ2 0x3
+#define EXYNOS5_FSEL_20MHZ 0x4
+#define EXYNOS5_FSEL_24MHZ 0x5
+#define EXYNOS5_FSEL_50MHZ 0x7
+
+/* EXYNOS5: USB 3.0 DRD PHY registers */
+#define EXYNOS5_DRD_LINKSYSTEM (0x04)
+
+#define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
+#define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
+#define LINKSYSTEM_XHCI_VERSION_CONTROL (0x1 << 27)
+
+#define EXYNOS5_DRD_PHYUTMI (0x08)
+
+#define PHYUTMI_OTGDISABLE (0x1 << 6)
+#define PHYUTMI_FORCESUSPEND (0x1 << 1)
+#define PHYUTMI_FORCESLEEP (0x1 << 0)
+
+#define EXYNOS5_DRD_PHYPIPE (0x0c)
+
+#define EXYNOS5_DRD_PHYCLKRST (0x10)
+
+#define PHYCLKRST_EN_UTMISUSPEND (0x1 << 31)
+
+#define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23)
+#define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23)
+
+#define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21)
+#define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21)
+
+#define PHYCLKRST_SSC_EN (0x1 << 20)
+#define PHYCLKRST_REF_SSP_EN (0x1 << 19)
+#define PHYCLKRST_REF_CLKDIV2 (0x1 << 18)
+
+#define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x32 << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
+
+#define PHYCLKRST_FSEL_MASK (0x3f << 5)
+#define PHYCLKRST_FSEL(_x) ((_x) << 5)
+#define PHYCLKRST_FSEL_PAD_100MHZ (0x27 << 5)
+#define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5)
+#define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5)
+#define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5)
+
+#define PHYCLKRST_RETENABLEN (0x1 << 4)
+
+#define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2)
+#define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2)
+#define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2)
+
+#define PHYCLKRST_PORTRESET (0x1 << 1)
+#define PHYCLKRST_COMMONONN (0x1 << 0)
+
+#define EXYNOS5_DRD_PHYREG0 (0x14)
+#define EXYNOS5_DRD_PHYREG1 (0x18)
+
+#define EXYNOS5_DRD_PHYPARAM0 (0x1c)
+
+#define PHYPARAM0_REF_USE_PAD (0x1 << 31)
+#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26)
+#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26)
+
+#define EXYNOS5_DRD_PHYPARAM1 (0x20)
+
+#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
+#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
+
+#define EXYNOS5_DRD_PHYTERM (0x24)
+
+#define EXYNOS5_DRD_PHYTEST (0x28)
+
+#define PHYTEST_POWERDOWN_SSP (0x1 << 3)
+#define PHYTEST_POWERDOWN_HSP (0x1 << 2)
+
+#define EXYNOS5_DRD_PHYADP (0x2c)
+
+#define EXYNOS5_DRD_PHYBATCHG (0x30)
+
+#define PHYBATCHG_UTMI_CLKSEL (0x1 << 2)
+
+#define EXYNOS5_DRD_PHYRESUME (0x34)
+#define EXYNOS5_DRD_LINKPORT (0x44)
+
+/* Power isolation defined in power management unit */
+#define EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET (0x704)
+#define EXYNOS5_USB3DRD_PMU_ISOL (1 << 0)
+
+#define KHZ 1000
+#define MHZ (KHZ * KHZ)
+
+enum exynos5_usb3phy_id {
+ EXYNOS5_USB3PHY_UTMI,
+ EXYNOS5_USB3PHY_PIPE3,
+ EXYNOS5_USB3PHYS_NUM,
+};
+
+struct usb3phy_config {
+ u32 id;
+ u32 reg_pmu_offset;
+ void (*phy_isol)(struct phy *phy, u32 on);
+};
+
+struct exynos5_usb3phy_drv_data {
+ bool has_usb30_sclk;
+ bool has_multi_controller;
+ const struct usb3phy_config *phy_cfg;
+};
+
+/**
+ * struct exynos5_usb3phy_driver - driver data for USB 3.0 PHY
+ * @dev: pointer to device instance of this platform device
+ * @reg_phy: usb phy controller register memory base
+ * @clk: phy clock for register access
+ * @usb30_sclk: additional special clock for phy operations
+ * @drv_data: pointer to SoC level driver data structure
+ * @phys[]: array for 'EXYNOS5_USB3PHYS_NUM' number of PHY
+ * instances each with its 'phy' and 'phy_cfg'.
+ * @extrefclk: frequency select settings when using 'separate
+ * reference clocks' for SS and HS operations
+ * @rate: rate of reference clock to PHY block
+ * @channel: number of PHY channels present in SoC
+ */
+struct exynos5_usb3phy_driver {
+ struct device *dev;
+ void __iomem *reg_phy;
+ struct clk *clk;
+ struct clk *usb30_sclk;
+ const struct exynos5_usb3phy_drv_data *drv_data;
+ struct phy_usb_instance {
+ struct phy *phy;
+ u32 index;
+ struct regmap *reg_isol;
+ const struct usb3phy_config *phy_cfg;
+ } phys[EXYNOS5_USB3PHYS_NUM];
+ u32 extrefclk;
+ unsigned long rate;
+ u32 channel;
+};
+
+#define to_usb3phy_driver(inst) \
+ container_of((inst), struct exynos5_usb3phy_driver, \
+ phys[(inst)->index]);
+
+/*
+ * exynos5_rate_to_clk() converts the supplied clock rate to the value that
+ * can be written to the phy register.
+ */
+static u32 exynos5_rate_to_clk(unsigned long rate)
+{
+ unsigned int clksel;
+
+ /* EXYNOS5_FSEL_MASK */
+
+ switch (rate) {
+ case 9600 * KHZ:
+ clksel = EXYNOS5_FSEL_9MHZ6;
+ break;
+ case 10 * MHZ:
+ clksel = EXYNOS5_FSEL_10MHZ;
+ break;
+ case 12 * MHZ:
+ clksel = EXYNOS5_FSEL_12MHZ;
+ break;
+ case 19200 * KHZ:
+ clksel = EXYNOS5_FSEL_19MHZ2;
+ break;
+ case 20 * MHZ:
+ clksel = EXYNOS5_FSEL_20MHZ;
+ break;
+ case 24 * MHZ:
+ clksel = EXYNOS5_FSEL_24MHZ;
+ break;
+ case 50 * MHZ:
+ clksel = EXYNOS5_FSEL_50MHZ;
+ break;
+ default:
+ clksel = -EINVAL;
+ }
+
+ return clksel;
+}
+
+static void exynos5_usb3phy_isol(struct phy *phy, unsigned int on)
+{
+ u32 pmu_offset;
+ struct phy_usb_instance *inst = phy_get_drvdata(phy);
+ struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
+
+ pmu_offset = inst->phy_cfg->reg_pmu_offset;
+ if (!inst->reg_isol)
+ return;
+
+ switch (drv->channel) {
+ case 1:
+ /* Channel 1 is at 0x708 offset */
+ pmu_offset += sizeof(&pmu_offset);
+ break;
+ case 0:
+ default:
+ /* Channel 0 is at 0x704 offset */
+ break;
+ }
+
+ regmap_update_bits(inst->reg_isol, pmu_offset,
+ EXYNOS5_USB3DRD_PMU_ISOL, ~on);
+}
+
+/*
+ * Sets the phy clk as EXTREFCLK (XXTI) which is internal clock from clock core.
+ */
+static u32 exynos5_usb3phy_set_refclk(struct exynos5_usb3phy_driver *drv)
+{
+ u32 reg;
+
+ reg = PHYCLKRST_REFCLKSEL_EXT_REFCLK |
+ PHYCLKRST_FSEL(drv->extrefclk);
+
+ switch (drv->extrefclk) {
+ case EXYNOS5_FSEL_50MHZ:
+ reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
+ PHYCLKRST_SSC_REFCLKSEL(0x00));
+ break;
+ case EXYNOS5_FSEL_24MHZ:
+ reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
+ PHYCLKRST_SSC_REFCLKSEL(0x88));
+ break;
+ case EXYNOS5_FSEL_20MHZ:
+ reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
+ PHYCLKRST_SSC_REFCLKSEL(0x00));
+ break;
+ case EXYNOS5_FSEL_19MHZ2:
+ reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
+ PHYCLKRST_SSC_REFCLKSEL(0x88));
+ break;
+ default:
+ dev_dbg(drv->dev, "unsupported ref clk\n");
+ break;
+ }
+
+ return reg;
+}
+
+static int exynos5_usb3phy_init(struct phy *phy)
+{
+ int ret;
+ u32 phyparam0;
+ u32 phyparam1;
+ u32 linksystem;
+ u32 phybatchg;
+ u32 phytest;
+ u32 phyclkrst;
+ struct phy_usb_instance *inst = phy_get_drvdata(phy);
+ struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
+
+ ret = clk_prepare_enable(drv->clk);
+ if (ret)
+ return ret;
+
+ drv->extrefclk = exynos5_rate_to_clk(drv->rate);
+ if (drv->extrefclk == -EINVAL) {
+ dev_err(drv->dev, "Clock rate (%ld) not supported\n",
+ drv->rate);
+ return -EINVAL;
+ }
+
+ /* Reset USB 3.0 PHY */
+ writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYREG0);
+
+ phyparam0 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
+ /* Select PHY CLK source */
+ phyparam0 &= ~PHYPARAM0_REF_USE_PAD;
+ /* Set Loss-of-Signal Detector sensitivity */
+ phyparam0 &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
+ phyparam0 |= PHYPARAM0_REF_LOSLEVEL;
+ writel(phyparam0, drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
+
+ writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYRESUME);
+
+ /*
+ * Setting the Frame length Adj value[6:1] to default 0x20
+ * See xHCI 1.0 spec, 5.2.4
+ */
+ linksystem = LINKSYSTEM_XHCI_VERSION_CONTROL |
+ LINKSYSTEM_FLADJ(0x20);
+ writel(linksystem, drv->reg_phy + EXYNOS5_DRD_LINKSYSTEM);
+
+ phyparam1 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
+ /* Set Tx De-Emphasis level */
+ phyparam1 &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
+ phyparam1 |= PHYPARAM1_PCS_TXDEEMPH;
+ writel(phyparam1, drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
+
+ phybatchg = readl(drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
+ phybatchg |= PHYBATCHG_UTMI_CLKSEL;
+ writel(phybatchg, drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
+
+ /* PHYTEST POWERDOWN Control */
+ phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
+ phytest &= ~(PHYTEST_POWERDOWN_SSP |
+ PHYTEST_POWERDOWN_HSP);
+ writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
+
+ /* UTMI Power Control */
+ writel(PHYUTMI_OTGDISABLE, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
+
+ phyclkrst = exynos5_usb3phy_set_refclk(drv);
+
+ phyclkrst |= PHYCLKRST_PORTRESET |
+ /* Digital power supply in normal operating mode */
+ PHYCLKRST_RETENABLEN |
+ /* Enable ref clock for SS function */
+ PHYCLKRST_REF_SSP_EN |
+ /* Enable spread spectrum */
+ PHYCLKRST_SSC_EN |
+ /* Power down HS Bias and PLL blocks in suspend mode */
+ PHYCLKRST_COMMONONN;
+
+ writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+
+ udelay(10);
+
+ phyclkrst &= ~PHYCLKRST_PORTRESET;
+ writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+
+ clk_disable_unprepare(drv->clk);
+
+ return 0;
+}
+
+static int exynos5_usb3phy_exit(struct phy *phy)
+{
+ int ret;
+ u32 phyutmi;
+ u32 phyclkrst;
+ u32 phytest;
+ struct phy_usb_instance *inst = phy_get_drvdata(phy);
+ struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
+
+ ret = clk_prepare_enable(drv->clk);
+ if (ret)
+ return ret;
+
+ phyutmi = PHYUTMI_OTGDISABLE |
+ PHYUTMI_FORCESUSPEND |
+ PHYUTMI_FORCESLEEP;
+ writel(phyutmi, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
+
+ /* Resetting the PHYCLKRST enable bits to reduce leakage current */
+ phyclkrst = readl(drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+ phyclkrst &= ~(PHYCLKRST_REF_SSP_EN |
+ PHYCLKRST_SSC_EN |
+ PHYCLKRST_COMMONONN);
+ writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+
+ /* Control PHYTEST to remove leakage current */
+ phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
+ phytest |= PHYTEST_POWERDOWN_SSP |
+ PHYTEST_POWERDOWN_HSP;
+ writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
+
+ clk_disable_unprepare(drv->clk);
+
+ return 0;
+}
+
+static int exynos5_usb3phy_power_on(struct phy *phy)
+{
+ struct phy_usb_instance *inst = phy_get_drvdata(phy);
+ struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
+
+ dev_dbg(drv->dev, "Request to power_on usb3drd phy\n");
+
+ if (!IS_ERR(drv->usb30_sclk))
+ clk_prepare_enable(drv->usb30_sclk);
+
+ /* Power-on PHY*/
+ inst->phy_cfg->phy_isol(phy, 0);
+
+ return 0;
+}
+
+static int exynos5_usb3phy_power_off(struct phy *phy)
+{
+ struct phy_usb_instance *inst = phy_get_drvdata(phy);
+ struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
+
+ dev_dbg(drv->dev, "Request to power_off usb3drd phy\n");
+
+ /* Power-off the PHY */
+ inst->phy_cfg->phy_isol(phy, 1);
+
+ if (!IS_ERR(drv->usb30_sclk))
+ clk_disable_unprepare(drv->usb30_sclk);
+
+ return 0;
+}
+
+static struct phy *exynos5_usb3phy_xlate(struct device *dev,
+ struct of_phandle_args *args)
+{
+ struct exynos5_usb3phy_driver *drv = dev_get_drvdata(dev);
+
+ if (WARN_ON(args->args[0] > EXYNOS5_USB3PHYS_NUM))
+ return ERR_PTR(-ENODEV);
+
+ return drv->phys[args->args[0]].phy;
+}
+
+static struct phy_ops exynos5_usb3phy_ops = {
+ .init = exynos5_usb3phy_init,
+ .exit = exynos5_usb3phy_exit,
+ .power_on = exynos5_usb3phy_power_on,
+ .power_off = exynos5_usb3phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+const struct usb3phy_config exynos5_usb3phy_cfg[] = {
+ {
+ .id = EXYNOS5_USB3PHY_UTMI,
+ .reg_pmu_offset = EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET,
+ .phy_isol = exynos5_usb3phy_isol,
+ },
+ {
+ .id = EXYNOS5_USB3PHY_PIPE3,
+ .reg_pmu_offset = EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET,
+ .phy_isol = exynos5_usb3phy_isol,
+ },
+ {},
+};
+
+const struct exynos5_usb3phy_drv_data exynos5420_usb3phy = {
+ .has_usb30_sclk = true,
+ .has_multi_controller = true,
+ .phy_cfg = exynos5_usb3phy_cfg,
+};
+
+const struct exynos5_usb3phy_drv_data exynos5250_usb3phy = {
+ .has_usb30_sclk = false,
+ .has_multi_controller = false,
+ .phy_cfg = exynos5_usb3phy_cfg,
+};
+
+static const struct of_device_id exynos5_usb3phy_of_match[] = {
+ {
+ .compatible = "samsung,exynos5250-usb3phy",
+ .data = &exynos5250_usb3phy
+ }, {
+ .compatible = "samsung,exynos5420-usb3phy",
+ .data = &exynos5420_usb3phy
+ },
+ { },
+};
+
+static int exynos5_usb3phy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *node = dev->of_node;
+ struct exynos5_usb3phy_driver *drv;
+ struct phy_provider *phy_provider;
+ struct resource *res;
+ struct clk *clk;
+ const struct of_device_id *match;
+ const struct exynos5_usb3phy_drv_data *drv_data;
+ struct regmap *reg_isol;
+ int i;
+
+ /*
+ * Exynos systems are completely DT enabled,
+ * so lets not have any platform data support for this driver.
+ */
+ if (!node) {
+ dev_err(dev, "no device node found\n");
+ return -ENODEV;
+ }
+
+ match = of_match_node(exynos5_usb3phy_of_match, pdev->dev.of_node);
+ if (!match) {
+ dev_err(dev, "of_match_node() failed\n");
+ return -EINVAL;
+ }
+ drv_data = match->data;
+
+ drv = devm_kzalloc(dev, sizeof(*drv), GFP_KERNEL);
+ if (!drv) {
+ dev_err(dev, "Failed to allocate memory\n");
+ return -ENOMEM;
+ }
+
+ dev_set_drvdata(dev, drv);
+ drv->dev = dev;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ drv->reg_phy = devm_ioremap_resource(dev, res);
+ if (IS_ERR(drv->reg_phy)) {
+ dev_err(dev, "Failed to map register memory (phy)\n");
+ return PTR_ERR(drv->reg_phy);
+ }
+
+ drv->drv_data = drv_data;
+
+ /*
+ * Exynos5420 SoC has multiple channels for USB 3.0 PHY, with
+ * each having separate power control registers.
+ * 'drv->channel' facilitates to set such registers.
+ */
+ if (drv->drv_data->has_multi_controller) {
+ drv->channel = of_alias_get_id(node, "usb3phy");
+ if (drv->channel < 0) {
+ dev_err(dev, "Invalid usb3drd phy node\n");
+ return -EINVAL;
+ }
+ }
+
+ drv->clk = devm_clk_get(dev, "phy");
+ if (IS_ERR(drv->clk)) {
+ dev_err(dev, "Failed to get clock of phy controller\n");
+ return PTR_ERR(drv->clk);
+ }
+
+ /*
+ * Exysno5420 SoC has an additional special clock, used for
+ * for USB 3.0 PHY operation, this clock goes to the PHY block
+ * as a reference clock to clock generation block of the controller,
+ * named as 'USB30_SCLK_100M'.
+ */
+ if (drv_data->has_usb30_sclk) {
+ drv->usb30_sclk = devm_clk_get(dev, "usb30_sclk_100m");
+ if (IS_ERR(drv->usb30_sclk)) {
+ dev_err(dev, "Failed to get phy reference clock\n");
+ return PTR_ERR(drv->usb30_sclk);
+ }
+ }
+
+ clk = clk_get(dev, "usb3phy_refclk");
+ if (IS_ERR(clk)) {
+ dev_err(dev, "Failed to get reference clock of usb3drd phy\n");
+ return PTR_ERR(clk);
+ }
+ drv->rate = clk_get_rate(clk);
+ clk_put(clk);
+
+ dev_dbg(dev, "Creating usb3drd phy\n");
+
+ reg_isol = syscon_regmap_lookup_by_phandle(dev->of_node,
+ "samsung,syscon-phandle");
+ if (IS_ERR(reg_isol)) {
+ dev_err(dev, "Failed to map register memory (isolation)\n");
+ return PTR_ERR(reg_isol);
+ }
+
+ for (i = 0; i < EXYNOS5_USB3PHYS_NUM; i++) {
+ struct phy *phy = devm_phy_create(dev, &exynos5_usb3phy_ops,
+ NULL);
+ if (IS_ERR(phy)) {
+ dev_err(dev, "Failed to create usb3drd phy\n");
+ return PTR_ERR(phy);
+ }
+
+ drv->phys[i].phy = phy;
+ drv->phys[i].index = i;
+ drv->phys[i].reg_isol = reg_isol;
+ drv->phys[i].phy_cfg = &drv_data->phy_cfg[i];
+ phy_set_drvdata(phy, &drv->phys[i]);
+ }
+
+ phy_provider = devm_of_phy_provider_register(dev,
+ exynos5_usb3phy_xlate);
+ if (IS_ERR(phy_provider)) {
+ dev_err(drv->dev, "Failed to register phy provider\n");
+ return PTR_ERR(phy_provider);
+ }
+
+ return 0;
+}
+
+static struct platform_driver exynos5_usb3phy_driver = {
+ .probe = exynos5_usb3phy_probe,
+ .driver = {
+ .of_match_table = exynos5_usb3phy_of_match,
+ .name = "exynos5-usb3phy",
+ .owner = THIS_MODULE,
+ }
+};
+
+module_platform_driver(exynos5_usb3phy_driver);
+MODULE_DESCRIPTION("Samsung EXYNOS5 series SoC USB 3.0 PHY driver");
+MODULE_AUTHOR("Vivek Gautam <[email protected]>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:exynos5-usb3phy");
--
1.7.10.4
On Mon, Jan 20, 2014 at 7:12 PM, Vivek Gautam <[email protected]> wrote:
> Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
> The new driver uses the generic PHY framework and will interact
> with DWC3 controller present on Exynos5 series of SoCs.
> Thereby, removing old phy-samsung-usb3 driver and related code
> used untill now which was based on usb/phy framework.
>
> Signed-off-by: Vivek Gautam <[email protected]>
Sorry, forgot to add a Reviewed-by tag from Felipe. :-(
Will update in the next version of patch after getting a feedback on this patch.
> ---
>
> Changes from v2:
> 1) Added support for multiple PHYs (UTMI+ and PIPE3) and
> related changes in the driver structuring.
> 2) Added a xlate function to get the required phy out of
> number of PHYs in mutiple PHY scenerio.
> 3) Changed the names of few structures and variables to
> have a clearer meaning.
> 4) Added 'usb3phy_config' structure to take care of mutiple
> phys for a SoC having 'exynos5_usb3phy_drv_data' driver data.
> 5) Not deleting support for old driver 'phy-samsung-usb3' until
> required support for generic phy is added to DWC3.
>
> .../devicetree/bindings/phy/samsung-phy.txt | 49 ++
> drivers/phy/Kconfig | 8 +
> drivers/phy/Makefile | 1 +
> drivers/phy/phy-exynos5-usb3.c | 621 ++++++++++++++++++++
> 4 files changed, 679 insertions(+)
> create mode 100644 drivers/phy/phy-exynos5-usb3.c
>
> diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt
> index c0fccaa..57079f8 100644
> --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
> +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
> @@ -20,3 +20,52 @@ Required properties:
> - compatible : should be "samsung,exynos5250-dp-video-phy";
> - reg : offset and length of the Display Port PHY register set;
> - #phy-cells : from the generic PHY bindings, must be 0;
> +
> +Samsung Exynos5 SoC series USB 3.0 PHY controller
> +--------------------------------------------------
> +
> +Required properties:
> +- compatible : Should be set to one of the following supported values:
> + - "samsung,exynos5250-usb3phy" - for exynos5250 SoC,
> + - "samsung,exynos5420-usb3phy" - for exynos5420 SoC.
> +- reg : Register offset and length of USB 3.0 PHY register set;
> +- clocks: Clock IDs array as required by the controller
> +- clock-names: names of clocks correseponding to IDs in the clock property;
> + Required clocks:
> + - phy: main PHY clock (same as USB 3.0 controller IP clock),
> + used for register access.
> + - usb3phy_refclk: PHY's reference clock (usually crystal clock),
> + associated by phy name, used to determine bit values for
> + clock settings register.
> + Additional clock required for Exynos5420:
> + - usb30_sclk_100m: Additional special clock used for PHY operation
> + depicted as 'sclk_usbphy30' in CMU of Exynos5420.
> +- samsung,syscon-phandle: phandle for syscon interface, which is used to
> + control pmu registers for power isolation.
> +- #phy-cells : from the generic PHY bindings, must be 1;
> +
> +For "samsung,exynos5250-usb3phy" and "samsung,exynos5420-usb3phy" compatible
> +PHYs, the second cell in the PHY specifier identifies the PHY id, which is
> +interpreted as follows:
> + 0 - UTMI+ type phy,
> + 1 - PIPE3 type phy,
> +
> +Example:
> + usb3_phy: usbphy@12100000 {
> + compatible = "samsung,exynos5250-usb3phy";
> + reg = <0x12100000 0x100>;
> + clocks = <&clock 286>, <&clock 1>;
> + clock-names = "phy", "usb3phy_refclk";
> + samsung,syscon-phandle = <&pmu_syscon>;
> + #phy-cells = <1>;
> + };
> +
> +- aliases: For SoCs like Exynos5420 having multiple USB PHY controllers,
> + 'usb3_phy' nodes should have numbered alias in the aliases node,
> + in the form of usb3phyN, N = 0, 1... (depending on number of
> + controllers).
> +Example:
> + aliases {
> + usb3phy0 = &usb3_phy0;
> + usb3phy1 = &usb3_phy1;
> + };
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 330ef2d..32f9f38 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -51,4 +51,12 @@ config PHY_EXYNOS_DP_VIDEO
> help
> Support for Display Port PHY found on Samsung EXYNOS SoCs.
>
> +config PHY_EXYNOS5_USB3
> + tristate "Exynos5 SoC series USB 3.0 PHY driver"
> + depends on ARCH_EXYNOS5
> + select GENERIC_PHY
> + select MFD_SYSCON
> + help
> + Enable USB 3.0 PHY support for Exynos 5 SoC series
> +
> endmenu
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index d0caae9..9c06a61 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -7,3 +7,4 @@ obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) += phy-exynos-dp-video.o
> obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
> obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
> obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
> +obj-$(CONFIG_PHY_EXYNOS5_USB3) += phy-exynos5-usb3.o
> diff --git a/drivers/phy/phy-exynos5-usb3.c b/drivers/phy/phy-exynos5-usb3.c
> new file mode 100644
> index 0000000..24efed0
> --- /dev/null
> +++ b/drivers/phy/phy-exynos5-usb3.c
> @@ -0,0 +1,621 @@
> +/*
> + * Samsung EXYNOS5 SoC series USB 3.0 PHY driver
> + *
> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> + * Author: Vivek Gautam <[email protected]>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/mutex.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/regmap.h>
> +
> +/* Exynos USB PHY registers */
> +#define EXYNOS5_FSEL_9MHZ6 0x0
> +#define EXYNOS5_FSEL_10MHZ 0x1
> +#define EXYNOS5_FSEL_12MHZ 0x2
> +#define EXYNOS5_FSEL_19MHZ2 0x3
> +#define EXYNOS5_FSEL_20MHZ 0x4
> +#define EXYNOS5_FSEL_24MHZ 0x5
> +#define EXYNOS5_FSEL_50MHZ 0x7
> +
> +/* EXYNOS5: USB 3.0 DRD PHY registers */
> +#define EXYNOS5_DRD_LINKSYSTEM (0x04)
> +
> +#define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
> +#define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
> +#define LINKSYSTEM_XHCI_VERSION_CONTROL (0x1 << 27)
> +
> +#define EXYNOS5_DRD_PHYUTMI (0x08)
> +
> +#define PHYUTMI_OTGDISABLE (0x1 << 6)
> +#define PHYUTMI_FORCESUSPEND (0x1 << 1)
> +#define PHYUTMI_FORCESLEEP (0x1 << 0)
> +
> +#define EXYNOS5_DRD_PHYPIPE (0x0c)
> +
> +#define EXYNOS5_DRD_PHYCLKRST (0x10)
> +
> +#define PHYCLKRST_EN_UTMISUSPEND (0x1 << 31)
> +
> +#define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23)
> +#define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23)
> +
> +#define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21)
> +#define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21)
> +
> +#define PHYCLKRST_SSC_EN (0x1 << 20)
> +#define PHYCLKRST_REF_SSP_EN (0x1 << 19)
> +#define PHYCLKRST_REF_CLKDIV2 (0x1 << 18)
> +
> +#define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x32 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
> +
> +#define PHYCLKRST_FSEL_MASK (0x3f << 5)
> +#define PHYCLKRST_FSEL(_x) ((_x) << 5)
> +#define PHYCLKRST_FSEL_PAD_100MHZ (0x27 << 5)
> +#define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5)
> +#define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5)
> +#define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5)
> +
> +#define PHYCLKRST_RETENABLEN (0x1 << 4)
> +
> +#define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2)
> +#define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2)
> +#define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2)
> +
> +#define PHYCLKRST_PORTRESET (0x1 << 1)
> +#define PHYCLKRST_COMMONONN (0x1 << 0)
> +
> +#define EXYNOS5_DRD_PHYREG0 (0x14)
> +#define EXYNOS5_DRD_PHYREG1 (0x18)
> +
> +#define EXYNOS5_DRD_PHYPARAM0 (0x1c)
> +
> +#define PHYPARAM0_REF_USE_PAD (0x1 << 31)
> +#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26)
> +#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26)
> +
> +#define EXYNOS5_DRD_PHYPARAM1 (0x20)
> +
> +#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
> +#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
> +
> +#define EXYNOS5_DRD_PHYTERM (0x24)
> +
> +#define EXYNOS5_DRD_PHYTEST (0x28)
> +
> +#define PHYTEST_POWERDOWN_SSP (0x1 << 3)
> +#define PHYTEST_POWERDOWN_HSP (0x1 << 2)
> +
> +#define EXYNOS5_DRD_PHYADP (0x2c)
> +
> +#define EXYNOS5_DRD_PHYBATCHG (0x30)
> +
> +#define PHYBATCHG_UTMI_CLKSEL (0x1 << 2)
> +
> +#define EXYNOS5_DRD_PHYRESUME (0x34)
> +#define EXYNOS5_DRD_LINKPORT (0x44)
> +
> +/* Power isolation defined in power management unit */
> +#define EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET (0x704)
> +#define EXYNOS5_USB3DRD_PMU_ISOL (1 << 0)
> +
> +#define KHZ 1000
> +#define MHZ (KHZ * KHZ)
> +
> +enum exynos5_usb3phy_id {
> + EXYNOS5_USB3PHY_UTMI,
> + EXYNOS5_USB3PHY_PIPE3,
> + EXYNOS5_USB3PHYS_NUM,
> +};
> +
> +struct usb3phy_config {
> + u32 id;
> + u32 reg_pmu_offset;
> + void (*phy_isol)(struct phy *phy, u32 on);
> +};
> +
> +struct exynos5_usb3phy_drv_data {
> + bool has_usb30_sclk;
> + bool has_multi_controller;
> + const struct usb3phy_config *phy_cfg;
> +};
> +
> +/**
> + * struct exynos5_usb3phy_driver - driver data for USB 3.0 PHY
> + * @dev: pointer to device instance of this platform device
> + * @reg_phy: usb phy controller register memory base
> + * @clk: phy clock for register access
> + * @usb30_sclk: additional special clock for phy operations
> + * @drv_data: pointer to SoC level driver data structure
> + * @phys[]: array for 'EXYNOS5_USB3PHYS_NUM' number of PHY
> + * instances each with its 'phy' and 'phy_cfg'.
> + * @extrefclk: frequency select settings when using 'separate
> + * reference clocks' for SS and HS operations
> + * @rate: rate of reference clock to PHY block
> + * @channel: number of PHY channels present in SoC
> + */
> +struct exynos5_usb3phy_driver {
> + struct device *dev;
> + void __iomem *reg_phy;
> + struct clk *clk;
> + struct clk *usb30_sclk;
> + const struct exynos5_usb3phy_drv_data *drv_data;
> + struct phy_usb_instance {
> + struct phy *phy;
> + u32 index;
> + struct regmap *reg_isol;
> + const struct usb3phy_config *phy_cfg;
> + } phys[EXYNOS5_USB3PHYS_NUM];
> + u32 extrefclk;
> + unsigned long rate;
> + u32 channel;
> +};
> +
> +#define to_usb3phy_driver(inst) \
> + container_of((inst), struct exynos5_usb3phy_driver, \
> + phys[(inst)->index]);
> +
> +/*
> + * exynos5_rate_to_clk() converts the supplied clock rate to the value that
> + * can be written to the phy register.
> + */
> +static u32 exynos5_rate_to_clk(unsigned long rate)
> +{
> + unsigned int clksel;
> +
> + /* EXYNOS5_FSEL_MASK */
> +
> + switch (rate) {
> + case 9600 * KHZ:
> + clksel = EXYNOS5_FSEL_9MHZ6;
> + break;
> + case 10 * MHZ:
> + clksel = EXYNOS5_FSEL_10MHZ;
> + break;
> + case 12 * MHZ:
> + clksel = EXYNOS5_FSEL_12MHZ;
> + break;
> + case 19200 * KHZ:
> + clksel = EXYNOS5_FSEL_19MHZ2;
> + break;
> + case 20 * MHZ:
> + clksel = EXYNOS5_FSEL_20MHZ;
> + break;
> + case 24 * MHZ:
> + clksel = EXYNOS5_FSEL_24MHZ;
> + break;
> + case 50 * MHZ:
> + clksel = EXYNOS5_FSEL_50MHZ;
> + break;
> + default:
> + clksel = -EINVAL;
> + }
> +
> + return clksel;
> +}
> +
> +static void exynos5_usb3phy_isol(struct phy *phy, unsigned int on)
> +{
> + u32 pmu_offset;
> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
> +
> + pmu_offset = inst->phy_cfg->reg_pmu_offset;
> + if (!inst->reg_isol)
> + return;
> +
> + switch (drv->channel) {
> + case 1:
> + /* Channel 1 is at 0x708 offset */
> + pmu_offset += sizeof(&pmu_offset);
> + break;
> + case 0:
> + default:
> + /* Channel 0 is at 0x704 offset */
> + break;
> + }
> +
> + regmap_update_bits(inst->reg_isol, pmu_offset,
> + EXYNOS5_USB3DRD_PMU_ISOL, ~on);
> +}
> +
> +/*
> + * Sets the phy clk as EXTREFCLK (XXTI) which is internal clock from clock core.
> + */
> +static u32 exynos5_usb3phy_set_refclk(struct exynos5_usb3phy_driver *drv)
> +{
> + u32 reg;
> +
> + reg = PHYCLKRST_REFCLKSEL_EXT_REFCLK |
> + PHYCLKRST_FSEL(drv->extrefclk);
> +
> + switch (drv->extrefclk) {
> + case EXYNOS5_FSEL_50MHZ:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x00));
> + break;
> + case EXYNOS5_FSEL_24MHZ:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x88));
> + break;
> + case EXYNOS5_FSEL_20MHZ:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x00));
> + break;
> + case EXYNOS5_FSEL_19MHZ2:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x88));
> + break;
> + default:
> + dev_dbg(drv->dev, "unsupported ref clk\n");
> + break;
> + }
> +
> + return reg;
> +}
> +
> +static int exynos5_usb3phy_init(struct phy *phy)
> +{
> + int ret;
> + u32 phyparam0;
> + u32 phyparam1;
> + u32 linksystem;
> + u32 phybatchg;
> + u32 phytest;
> + u32 phyclkrst;
> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
> +
> + ret = clk_prepare_enable(drv->clk);
> + if (ret)
> + return ret;
> +
> + drv->extrefclk = exynos5_rate_to_clk(drv->rate);
> + if (drv->extrefclk == -EINVAL) {
> + dev_err(drv->dev, "Clock rate (%ld) not supported\n",
> + drv->rate);
> + return -EINVAL;
> + }
> +
> + /* Reset USB 3.0 PHY */
> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYREG0);
> +
> + phyparam0 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
> + /* Select PHY CLK source */
> + phyparam0 &= ~PHYPARAM0_REF_USE_PAD;
> + /* Set Loss-of-Signal Detector sensitivity */
> + phyparam0 &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
> + phyparam0 |= PHYPARAM0_REF_LOSLEVEL;
> + writel(phyparam0, drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
> +
> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYRESUME);
> +
> + /*
> + * Setting the Frame length Adj value[6:1] to default 0x20
> + * See xHCI 1.0 spec, 5.2.4
> + */
> + linksystem = LINKSYSTEM_XHCI_VERSION_CONTROL |
> + LINKSYSTEM_FLADJ(0x20);
> + writel(linksystem, drv->reg_phy + EXYNOS5_DRD_LINKSYSTEM);
> +
> + phyparam1 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
> + /* Set Tx De-Emphasis level */
> + phyparam1 &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
> + phyparam1 |= PHYPARAM1_PCS_TXDEEMPH;
> + writel(phyparam1, drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
> +
> + phybatchg = readl(drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
> + phybatchg |= PHYBATCHG_UTMI_CLKSEL;
> + writel(phybatchg, drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
> +
> + /* PHYTEST POWERDOWN Control */
> + phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> + phytest &= ~(PHYTEST_POWERDOWN_SSP |
> + PHYTEST_POWERDOWN_HSP);
> + writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> +
> + /* UTMI Power Control */
> + writel(PHYUTMI_OTGDISABLE, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
> +
> + phyclkrst = exynos5_usb3phy_set_refclk(drv);
> +
> + phyclkrst |= PHYCLKRST_PORTRESET |
> + /* Digital power supply in normal operating mode */
> + PHYCLKRST_RETENABLEN |
> + /* Enable ref clock for SS function */
> + PHYCLKRST_REF_SSP_EN |
> + /* Enable spread spectrum */
> + PHYCLKRST_SSC_EN |
> + /* Power down HS Bias and PLL blocks in suspend mode */
> + PHYCLKRST_COMMONONN;
> +
> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +
> + udelay(10);
> +
> + phyclkrst &= ~PHYCLKRST_PORTRESET;
> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +
> + clk_disable_unprepare(drv->clk);
> +
> + return 0;
> +}
> +
> +static int exynos5_usb3phy_exit(struct phy *phy)
> +{
> + int ret;
> + u32 phyutmi;
> + u32 phyclkrst;
> + u32 phytest;
> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
> +
> + ret = clk_prepare_enable(drv->clk);
> + if (ret)
> + return ret;
> +
> + phyutmi = PHYUTMI_OTGDISABLE |
> + PHYUTMI_FORCESUSPEND |
> + PHYUTMI_FORCESLEEP;
> + writel(phyutmi, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
> +
> + /* Resetting the PHYCLKRST enable bits to reduce leakage current */
> + phyclkrst = readl(drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> + phyclkrst &= ~(PHYCLKRST_REF_SSP_EN |
> + PHYCLKRST_SSC_EN |
> + PHYCLKRST_COMMONONN);
> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +
> + /* Control PHYTEST to remove leakage current */
> + phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> + phytest |= PHYTEST_POWERDOWN_SSP |
> + PHYTEST_POWERDOWN_HSP;
> + writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> +
> + clk_disable_unprepare(drv->clk);
> +
> + return 0;
> +}
> +
> +static int exynos5_usb3phy_power_on(struct phy *phy)
> +{
> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
> +
> + dev_dbg(drv->dev, "Request to power_on usb3drd phy\n");
> +
> + if (!IS_ERR(drv->usb30_sclk))
> + clk_prepare_enable(drv->usb30_sclk);
> +
> + /* Power-on PHY*/
> + inst->phy_cfg->phy_isol(phy, 0);
> +
> + return 0;
> +}
> +
> +static int exynos5_usb3phy_power_off(struct phy *phy)
> +{
> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
> +
> + dev_dbg(drv->dev, "Request to power_off usb3drd phy\n");
> +
> + /* Power-off the PHY */
> + inst->phy_cfg->phy_isol(phy, 1);
> +
> + if (!IS_ERR(drv->usb30_sclk))
> + clk_disable_unprepare(drv->usb30_sclk);
> +
> + return 0;
> +}
> +
> +static struct phy *exynos5_usb3phy_xlate(struct device *dev,
> + struct of_phandle_args *args)
> +{
> + struct exynos5_usb3phy_driver *drv = dev_get_drvdata(dev);
> +
> + if (WARN_ON(args->args[0] > EXYNOS5_USB3PHYS_NUM))
> + return ERR_PTR(-ENODEV);
> +
> + return drv->phys[args->args[0]].phy;
> +}
> +
> +static struct phy_ops exynos5_usb3phy_ops = {
> + .init = exynos5_usb3phy_init,
> + .exit = exynos5_usb3phy_exit,
> + .power_on = exynos5_usb3phy_power_on,
> + .power_off = exynos5_usb3phy_power_off,
> + .owner = THIS_MODULE,
> +};
> +
> +const struct usb3phy_config exynos5_usb3phy_cfg[] = {
> + {
> + .id = EXYNOS5_USB3PHY_UTMI,
> + .reg_pmu_offset = EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET,
> + .phy_isol = exynos5_usb3phy_isol,
> + },
> + {
> + .id = EXYNOS5_USB3PHY_PIPE3,
> + .reg_pmu_offset = EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET,
> + .phy_isol = exynos5_usb3phy_isol,
> + },
> + {},
> +};
> +
> +const struct exynos5_usb3phy_drv_data exynos5420_usb3phy = {
> + .has_usb30_sclk = true,
> + .has_multi_controller = true,
> + .phy_cfg = exynos5_usb3phy_cfg,
> +};
> +
> +const struct exynos5_usb3phy_drv_data exynos5250_usb3phy = {
> + .has_usb30_sclk = false,
> + .has_multi_controller = false,
> + .phy_cfg = exynos5_usb3phy_cfg,
> +};
> +
> +static const struct of_device_id exynos5_usb3phy_of_match[] = {
> + {
> + .compatible = "samsung,exynos5250-usb3phy",
> + .data = &exynos5250_usb3phy
> + }, {
> + .compatible = "samsung,exynos5420-usb3phy",
> + .data = &exynos5420_usb3phy
> + },
> + { },
> +};
> +
> +static int exynos5_usb3phy_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct device_node *node = dev->of_node;
> + struct exynos5_usb3phy_driver *drv;
> + struct phy_provider *phy_provider;
> + struct resource *res;
> + struct clk *clk;
> + const struct of_device_id *match;
> + const struct exynos5_usb3phy_drv_data *drv_data;
> + struct regmap *reg_isol;
> + int i;
> +
> + /*
> + * Exynos systems are completely DT enabled,
> + * so lets not have any platform data support for this driver.
> + */
> + if (!node) {
> + dev_err(dev, "no device node found\n");
> + return -ENODEV;
> + }
> +
> + match = of_match_node(exynos5_usb3phy_of_match, pdev->dev.of_node);
> + if (!match) {
> + dev_err(dev, "of_match_node() failed\n");
> + return -EINVAL;
> + }
> + drv_data = match->data;
> +
> + drv = devm_kzalloc(dev, sizeof(*drv), GFP_KERNEL);
> + if (!drv) {
> + dev_err(dev, "Failed to allocate memory\n");
> + return -ENOMEM;
> + }
> +
> + dev_set_drvdata(dev, drv);
> + drv->dev = dev;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + drv->reg_phy = devm_ioremap_resource(dev, res);
> + if (IS_ERR(drv->reg_phy)) {
> + dev_err(dev, "Failed to map register memory (phy)\n");
> + return PTR_ERR(drv->reg_phy);
> + }
> +
> + drv->drv_data = drv_data;
> +
> + /*
> + * Exynos5420 SoC has multiple channels for USB 3.0 PHY, with
> + * each having separate power control registers.
> + * 'drv->channel' facilitates to set such registers.
> + */
> + if (drv->drv_data->has_multi_controller) {
> + drv->channel = of_alias_get_id(node, "usb3phy");
> + if (drv->channel < 0) {
> + dev_err(dev, "Invalid usb3drd phy node\n");
> + return -EINVAL;
> + }
> + }
> +
> + drv->clk = devm_clk_get(dev, "phy");
> + if (IS_ERR(drv->clk)) {
> + dev_err(dev, "Failed to get clock of phy controller\n");
> + return PTR_ERR(drv->clk);
> + }
> +
> + /*
> + * Exysno5420 SoC has an additional special clock, used for
> + * for USB 3.0 PHY operation, this clock goes to the PHY block
> + * as a reference clock to clock generation block of the controller,
> + * named as 'USB30_SCLK_100M'.
> + */
> + if (drv_data->has_usb30_sclk) {
> + drv->usb30_sclk = devm_clk_get(dev, "usb30_sclk_100m");
> + if (IS_ERR(drv->usb30_sclk)) {
> + dev_err(dev, "Failed to get phy reference clock\n");
> + return PTR_ERR(drv->usb30_sclk);
> + }
> + }
> +
> + clk = clk_get(dev, "usb3phy_refclk");
> + if (IS_ERR(clk)) {
> + dev_err(dev, "Failed to get reference clock of usb3drd phy\n");
> + return PTR_ERR(clk);
> + }
> + drv->rate = clk_get_rate(clk);
> + clk_put(clk);
> +
> + dev_dbg(dev, "Creating usb3drd phy\n");
> +
> + reg_isol = syscon_regmap_lookup_by_phandle(dev->of_node,
> + "samsung,syscon-phandle");
> + if (IS_ERR(reg_isol)) {
> + dev_err(dev, "Failed to map register memory (isolation)\n");
> + return PTR_ERR(reg_isol);
> + }
> +
> + for (i = 0; i < EXYNOS5_USB3PHYS_NUM; i++) {
> + struct phy *phy = devm_phy_create(dev, &exynos5_usb3phy_ops,
> + NULL);
> + if (IS_ERR(phy)) {
> + dev_err(dev, "Failed to create usb3drd phy\n");
> + return PTR_ERR(phy);
> + }
> +
> + drv->phys[i].phy = phy;
> + drv->phys[i].index = i;
> + drv->phys[i].reg_isol = reg_isol;
> + drv->phys[i].phy_cfg = &drv_data->phy_cfg[i];
> + phy_set_drvdata(phy, &drv->phys[i]);
> + }
> +
> + phy_provider = devm_of_phy_provider_register(dev,
> + exynos5_usb3phy_xlate);
> + if (IS_ERR(phy_provider)) {
> + dev_err(drv->dev, "Failed to register phy provider\n");
> + return PTR_ERR(phy_provider);
> + }
> +
> + return 0;
> +}
> +
> +static struct platform_driver exynos5_usb3phy_driver = {
> + .probe = exynos5_usb3phy_probe,
> + .driver = {
> + .of_match_table = exynos5_usb3phy_of_match,
> + .name = "exynos5-usb3phy",
> + .owner = THIS_MODULE,
> + }
> +};
> +
> +module_platform_driver(exynos5_usb3phy_driver);
> +MODULE_DESCRIPTION("Samsung EXYNOS5 series SoC USB 3.0 PHY driver");
> +MODULE_AUTHOR("Vivek Gautam <[email protected]>");
> +MODULE_LICENSE("GPL v2");
> +MODULE_ALIAS("platform:exynos5-usb3phy");
> --
> 1.7.10.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
Best Regards
Vivek Gautam
Samsung R&D Institute, Bangalore
India
Hi,
On Monday 20 January 2014 07:12 PM, Vivek Gautam wrote:
> Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
> The new driver uses the generic PHY framework and will interact
> with DWC3 controller present on Exynos5 series of SoCs.
> Thereby, removing old phy-samsung-usb3 driver and related code
> used untill now which was based on usb/phy framework.
>
> Signed-off-by: Vivek Gautam <[email protected]>
> ---
>
> Changes from v2:
> 1) Added support for multiple PHYs (UTMI+ and PIPE3) and
> related changes in the driver structuring.
> 2) Added a xlate function to get the required phy out of
> number of PHYs in mutiple PHY scenerio.
> 3) Changed the names of few structures and variables to
> have a clearer meaning.
> 4) Added 'usb3phy_config' structure to take care of mutiple
> phys for a SoC having 'exynos5_usb3phy_drv_data' driver data.
> 5) Not deleting support for old driver 'phy-samsung-usb3' until
> required support for generic phy is added to DWC3.
>
> .../devicetree/bindings/phy/samsung-phy.txt | 49 ++
> drivers/phy/Kconfig | 8 +
> drivers/phy/Makefile | 1 +
> drivers/phy/phy-exynos5-usb3.c | 621 ++++++++++++++++++++
> 4 files changed, 679 insertions(+)
> create mode 100644 drivers/phy/phy-exynos5-usb3.c
>
> diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt
> index c0fccaa..57079f8 100644
> --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
> +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
> @@ -20,3 +20,52 @@ Required properties:
> - compatible : should be "samsung,exynos5250-dp-video-phy";
> - reg : offset and length of the Display Port PHY register set;
> - #phy-cells : from the generic PHY bindings, must be 0;
> +
> +Samsung Exynos5 SoC series USB 3.0 PHY controller
> +--------------------------------------------------
> +
> +Required properties:
> +- compatible : Should be set to one of the following supported values:
> + - "samsung,exynos5250-usb3phy" - for exynos5250 SoC,
> + - "samsung,exynos5420-usb3phy" - for exynos5420 SoC.
> +- reg : Register offset and length of USB 3.0 PHY register set;
> +- clocks: Clock IDs array as required by the controller
> +- clock-names: names of clocks correseponding to IDs in the clock property;
> + Required clocks:
> + - phy: main PHY clock (same as USB 3.0 controller IP clock),
> + used for register access.
> + - usb3phy_refclk: PHY's reference clock (usually crystal clock),
> + associated by phy name, used to determine bit values for
> + clock settings register.
> + Additional clock required for Exynos5420:
> + - usb30_sclk_100m: Additional special clock used for PHY operation
> + depicted as 'sclk_usbphy30' in CMU of Exynos5420.
> +- samsung,syscon-phandle: phandle for syscon interface, which is used to
> + control pmu registers for power isolation.
> +- #phy-cells : from the generic PHY bindings, must be 1;
> +
> +For "samsung,exynos5250-usb3phy" and "samsung,exynos5420-usb3phy" compatible
> +PHYs, the second cell in the PHY specifier identifies the PHY id, which is
> +interpreted as follows:
> + 0 - UTMI+ type phy,
> + 1 - PIPE3 type phy,
> +
> +Example:
> + usb3_phy: usbphy@12100000 {
> + compatible = "samsung,exynos5250-usb3phy";
> + reg = <0x12100000 0x100>;
> + clocks = <&clock 286>, <&clock 1>;
> + clock-names = "phy", "usb3phy_refclk";
> + samsung,syscon-phandle = <&pmu_syscon>;
> + #phy-cells = <1>;
> + };
> +
> +- aliases: For SoCs like Exynos5420 having multiple USB PHY controllers,
> + 'usb3_phy' nodes should have numbered alias in the aliases node,
> + in the form of usb3phyN, N = 0, 1... (depending on number of
> + controllers).
> +Example:
> + aliases {
> + usb3phy0 = &usb3_phy0;
> + usb3phy1 = &usb3_phy1;
> + };
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 330ef2d..32f9f38 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -51,4 +51,12 @@ config PHY_EXYNOS_DP_VIDEO
> help
> Support for Display Port PHY found on Samsung EXYNOS SoCs.
>
> +config PHY_EXYNOS5_USB3
> + tristate "Exynos5 SoC series USB 3.0 PHY driver"
> + depends on ARCH_EXYNOS5
> + select GENERIC_PHY
> + select MFD_SYSCON
add depends on 'HAS_IOMEM'. Someone reported getting
undefined reference to `devm_ioremap_resource' with it.
> + help
> + Enable USB 3.0 PHY support for Exynos 5 SoC series
> +
> endmenu
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index d0caae9..9c06a61 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -7,3 +7,4 @@ obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) += phy-exynos-dp-video.o
> obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
> obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
> obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
> +obj-$(CONFIG_PHY_EXYNOS5_USB3) += phy-exynos5-usb3.o
> diff --git a/drivers/phy/phy-exynos5-usb3.c b/drivers/phy/phy-exynos5-usb3.c
> new file mode 100644
> index 0000000..24efed0
> --- /dev/null
> +++ b/drivers/phy/phy-exynos5-usb3.c
> @@ -0,0 +1,621 @@
> +/*
> + * Samsung EXYNOS5 SoC series USB 3.0 PHY driver
> + *
> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> + * Author: Vivek Gautam <[email protected]>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/mutex.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/regmap.h>
> +
> +/* Exynos USB PHY registers */
> +#define EXYNOS5_FSEL_9MHZ6 0x0
> +#define EXYNOS5_FSEL_10MHZ 0x1
> +#define EXYNOS5_FSEL_12MHZ 0x2
> +#define EXYNOS5_FSEL_19MHZ2 0x3
> +#define EXYNOS5_FSEL_20MHZ 0x4
> +#define EXYNOS5_FSEL_24MHZ 0x5
> +#define EXYNOS5_FSEL_50MHZ 0x7
> +
> +/* EXYNOS5: USB 3.0 DRD PHY registers */
> +#define EXYNOS5_DRD_LINKSYSTEM (0x04)
> +
> +#define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
> +#define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
> +#define LINKSYSTEM_XHCI_VERSION_CONTROL (0x1 << 27)
> +
> +#define EXYNOS5_DRD_PHYUTMI (0x08)
> +
> +#define PHYUTMI_OTGDISABLE (0x1 << 6)
> +#define PHYUTMI_FORCESUSPEND (0x1 << 1)
> +#define PHYUTMI_FORCESLEEP (0x1 << 0)
use BIT macro here and below?
> +
> +#define EXYNOS5_DRD_PHYPIPE (0x0c)
> +
> +#define EXYNOS5_DRD_PHYCLKRST (0x10)
> +
> +#define PHYCLKRST_EN_UTMISUSPEND (0x1 << 31)
> +
> +#define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23)
> +#define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23)
> +
> +#define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21)
> +#define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21)
> +
> +#define PHYCLKRST_SSC_EN (0x1 << 20)
> +#define PHYCLKRST_REF_SSP_EN (0x1 << 19)
> +#define PHYCLKRST_REF_CLKDIV2 (0x1 << 18)
> +
> +#define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x32 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
> +
> +#define PHYCLKRST_FSEL_MASK (0x3f << 5)
> +#define PHYCLKRST_FSEL(_x) ((_x) << 5)
> +#define PHYCLKRST_FSEL_PAD_100MHZ (0x27 << 5)
> +#define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5)
> +#define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5)
> +#define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5)
> +
> +#define PHYCLKRST_RETENABLEN (0x1 << 4)
> +
> +#define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2)
> +#define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2)
> +#define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2)
> +
> +#define PHYCLKRST_PORTRESET (0x1 << 1)
> +#define PHYCLKRST_COMMONONN (0x1 << 0)
> +
> +#define EXYNOS5_DRD_PHYREG0 (0x14)
> +#define EXYNOS5_DRD_PHYREG1 (0x18)
> +
> +#define EXYNOS5_DRD_PHYPARAM0 (0x1c)
> +
> +#define PHYPARAM0_REF_USE_PAD (0x1 << 31)
> +#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26)
> +#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26)
> +
> +#define EXYNOS5_DRD_PHYPARAM1 (0x20)
> +
> +#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
> +#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
> +
> +#define EXYNOS5_DRD_PHYTERM (0x24)
> +
> +#define EXYNOS5_DRD_PHYTEST (0x28)
> +
> +#define PHYTEST_POWERDOWN_SSP (0x1 << 3)
> +#define PHYTEST_POWERDOWN_HSP (0x1 << 2)
> +
> +#define EXYNOS5_DRD_PHYADP (0x2c)
> +
> +#define EXYNOS5_DRD_PHYBATCHG (0x30)
> +
> +#define PHYBATCHG_UTMI_CLKSEL (0x1 << 2)
> +
> +#define EXYNOS5_DRD_PHYRESUME (0x34)
> +#define EXYNOS5_DRD_LINKPORT (0x44)
> +
> +/* Power isolation defined in power management unit */
> +#define EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET (0x704)
> +#define EXYNOS5_USB3DRD_PMU_ISOL (1 << 0)
> +
> +#define KHZ 1000
> +#define MHZ (KHZ * KHZ)
> +
> +enum exynos5_usb3phy_id {
> + EXYNOS5_USB3PHY_UTMI,
> + EXYNOS5_USB3PHY_PIPE3,
> + EXYNOS5_USB3PHYS_NUM,
> +};
> +
> +struct usb3phy_config {
> + u32 id;
> + u32 reg_pmu_offset;
> + void (*phy_isol)(struct phy *phy, u32 on);
> +};
> +
> +struct exynos5_usb3phy_drv_data {
> + bool has_usb30_sclk;
> + bool has_multi_controller;
> + const struct usb3phy_config *phy_cfg;
> +};
> +
> +/**
> + * struct exynos5_usb3phy_driver - driver data for USB 3.0 PHY
Is this really a driver data? I think it should be just exynos5_usb3phy.
> + * @dev: pointer to device instance of this platform device
> + * @reg_phy: usb phy controller register memory base
> + * @clk: phy clock for register access
> + * @usb30_sclk: additional special clock for phy operations
> + * @drv_data: pointer to SoC level driver data structure
> + * @phys[]: array for 'EXYNOS5_USB3PHYS_NUM' number of PHY
> + * instances each with its 'phy' and 'phy_cfg'.
> + * @extrefclk: frequency select settings when using 'separate
> + * reference clocks' for SS and HS operations
> + * @rate: rate of reference clock to PHY block
> + * @channel: number of PHY channels present in SoC
> + */
> +struct exynos5_usb3phy_driver {
> + struct device *dev;
> + void __iomem *reg_phy;
> + struct clk *clk;
> + struct clk *usb30_sclk;
> + const struct exynos5_usb3phy_drv_data *drv_data;
> + struct phy_usb_instance {
> + struct phy *phy;
> + u32 index;
> + struct regmap *reg_isol;
> + const struct usb3phy_config *phy_cfg;
> + } phys[EXYNOS5_USB3PHYS_NUM];
> + u32 extrefclk;
> + unsigned long rate;
> + u32 channel;
> +};
> +
> +#define to_usb3phy_driver(inst) \
> + container_of((inst), struct exynos5_usb3phy_driver, \
> + phys[(inst)->index]);
> +
> +/*
> + * exynos5_rate_to_clk() converts the supplied clock rate to the value that
> + * can be written to the phy register.
> + */
> +static u32 exynos5_rate_to_clk(unsigned long rate)
> +{
> + unsigned int clksel;
> +
> + /* EXYNOS5_FSEL_MASK */
> +
> + switch (rate) {
> + case 9600 * KHZ:
> + clksel = EXYNOS5_FSEL_9MHZ6;
> + break;
> + case 10 * MHZ:
> + clksel = EXYNOS5_FSEL_10MHZ;
> + break;
> + case 12 * MHZ:
> + clksel = EXYNOS5_FSEL_12MHZ;
> + break;
> + case 19200 * KHZ:
> + clksel = EXYNOS5_FSEL_19MHZ2;
> + break;
> + case 20 * MHZ:
> + clksel = EXYNOS5_FSEL_20MHZ;
> + break;
> + case 24 * MHZ:
> + clksel = EXYNOS5_FSEL_24MHZ;
> + break;
> + case 50 * MHZ:
> + clksel = EXYNOS5_FSEL_50MHZ;
> + break;
> + default:
> + clksel = -EINVAL;
> + }
> +
> + return clksel;
> +}
> +
> +static void exynos5_usb3phy_isol(struct phy *phy, unsigned int on)
> +{
> + u32 pmu_offset;
> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
> +
> + pmu_offset = inst->phy_cfg->reg_pmu_offset;
> + if (!inst->reg_isol)
> + return;
> +
> + switch (drv->channel) {
> + case 1:
> + /* Channel 1 is at 0x708 offset */
> + pmu_offset += sizeof(&pmu_offset);
> + break;
> + case 0:
> + default:
> + /* Channel 0 is at 0x704 offset */
> + break;
> + }
This can be in a simple 'if' stmt no?
> +
> + regmap_update_bits(inst->reg_isol, pmu_offset,
> + EXYNOS5_USB3DRD_PMU_ISOL, ~on);
> +}
> +
> +/*
> + * Sets the phy clk as EXTREFCLK (XXTI) which is internal clock from clock core.
> + */
> +static u32 exynos5_usb3phy_set_refclk(struct exynos5_usb3phy_driver *drv)
> +{
> + u32 reg;
> +
> + reg = PHYCLKRST_REFCLKSEL_EXT_REFCLK |
> + PHYCLKRST_FSEL(drv->extrefclk);
> +
> + switch (drv->extrefclk) {
> + case EXYNOS5_FSEL_50MHZ:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x00));
> + break;
> + case EXYNOS5_FSEL_24MHZ:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x88));
> + break;
> + case EXYNOS5_FSEL_20MHZ:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x00));
> + break;
> + case EXYNOS5_FSEL_19MHZ2:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x88));
> + break;
> + default:
> + dev_dbg(drv->dev, "unsupported ref clk\n");
> + break;
> + }
> +
> + return reg;
> +}
> +
> +static int exynos5_usb3phy_init(struct phy *phy)
> +{
> + int ret;
> + u32 phyparam0;
> + u32 phyparam1;
> + u32 linksystem;
> + u32 phybatchg;
> + u32 phytest;
> + u32 phyclkrst;
instead you can define a single variable 'u32 reg' for register read and writes.
> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
> +
> + ret = clk_prepare_enable(drv->clk);
> + if (ret)
> + return ret;
> +
> + drv->extrefclk = exynos5_rate_to_clk(drv->rate);
> + if (drv->extrefclk == -EINVAL) {
> + dev_err(drv->dev, "Clock rate (%ld) not supported\n",
> + drv->rate);
> + return -EINVAL;
> + }
> +
> + /* Reset USB 3.0 PHY */
> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYREG0);
> +
> + phyparam0 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
> + /* Select PHY CLK source */
> + phyparam0 &= ~PHYPARAM0_REF_USE_PAD;
> + /* Set Loss-of-Signal Detector sensitivity */
> + phyparam0 &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
> + phyparam0 |= PHYPARAM0_REF_LOSLEVEL;
> + writel(phyparam0, drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
> +
> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYRESUME);
> +
> + /*
> + * Setting the Frame length Adj value[6:1] to default 0x20
> + * See xHCI 1.0 spec, 5.2.4
> + */
> + linksystem = LINKSYSTEM_XHCI_VERSION_CONTROL |
> + LINKSYSTEM_FLADJ(0x20);
> + writel(linksystem, drv->reg_phy + EXYNOS5_DRD_LINKSYSTEM);
> +
> + phyparam1 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
> + /* Set Tx De-Emphasis level */
> + phyparam1 &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
> + phyparam1 |= PHYPARAM1_PCS_TXDEEMPH;
> + writel(phyparam1, drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
> +
> + phybatchg = readl(drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
> + phybatchg |= PHYBATCHG_UTMI_CLKSEL;
> + writel(phybatchg, drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
> +
> + /* PHYTEST POWERDOWN Control */
> + phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> + phytest &= ~(PHYTEST_POWERDOWN_SSP |
> + PHYTEST_POWERDOWN_HSP);
> + writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> +
> + /* UTMI Power Control */
> + writel(PHYUTMI_OTGDISABLE, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
All these UTMI configuration should be done in usb2 init.
> +
> + phyclkrst = exynos5_usb3phy_set_refclk(drv);
> +
> + phyclkrst |= PHYCLKRST_PORTRESET |
> + /* Digital power supply in normal operating mode */
> + PHYCLKRST_RETENABLEN |
> + /* Enable ref clock for SS function */
> + PHYCLKRST_REF_SSP_EN |
> + /* Enable spread spectrum */
> + PHYCLKRST_SSC_EN |
> + /* Power down HS Bias and PLL blocks in suspend mode */
> + PHYCLKRST_COMMONONN;
> +
> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +
> + udelay(10);
> +
> + phyclkrst &= ~PHYCLKRST_PORTRESET;
> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +
> + clk_disable_unprepare(drv->clk);
> +
> + return 0;
> +}
> +
> +static int exynos5_usb3phy_exit(struct phy *phy)
> +{
> + int ret;
> + u32 phyutmi;
> + u32 phyclkrst;
> + u32 phytest;
same here..
> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
> +
> + ret = clk_prepare_enable(drv->clk);
> + if (ret)
> + return ret;
> +
> + phyutmi = PHYUTMI_OTGDISABLE |
> + PHYUTMI_FORCESUSPEND |
> + PHYUTMI_FORCESLEEP;
> + writel(phyutmi, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
here too.. UTMI configuration should be part of USB2.
> +
> + /* Resetting the PHYCLKRST enable bits to reduce leakage current */
> + phyclkrst = readl(drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> + phyclkrst &= ~(PHYCLKRST_REF_SSP_EN |
> + PHYCLKRST_SSC_EN |
> + PHYCLKRST_COMMONONN);
> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +
> + /* Control PHYTEST to remove leakage current */
> + phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> + phytest |= PHYTEST_POWERDOWN_SSP |
> + PHYTEST_POWERDOWN_HSP;
> + writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> +
> + clk_disable_unprepare(drv->clk);
> +
> + return 0;
> +}
> +
> +static int exynos5_usb3phy_power_on(struct phy *phy)
> +{
> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
> +
> + dev_dbg(drv->dev, "Request to power_on usb3drd phy\n");
> +
> + if (!IS_ERR(drv->usb30_sclk))
> + clk_prepare_enable(drv->usb30_sclk);
> +
> + /* Power-on PHY*/
> + inst->phy_cfg->phy_isol(phy, 0);
> +
> + return 0;
> +}
> +
> +static int exynos5_usb3phy_power_off(struct phy *phy)
> +{
> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
> +
> + dev_dbg(drv->dev, "Request to power_off usb3drd phy\n");
> +
> + /* Power-off the PHY */
> + inst->phy_cfg->phy_isol(phy, 1);
> +
> + if (!IS_ERR(drv->usb30_sclk))
> + clk_disable_unprepare(drv->usb30_sclk);
> +
> + return 0;
> +}
> +
> +static struct phy *exynos5_usb3phy_xlate(struct device *dev,
> + struct of_phandle_args *args)
> +{
> + struct exynos5_usb3phy_driver *drv = dev_get_drvdata(dev);
> +
> + if (WARN_ON(args->args[0] > EXYNOS5_USB3PHYS_NUM))
> + return ERR_PTR(-ENODEV);
> +
> + return drv->phys[args->args[0]].phy;
> +}
> +
> +static struct phy_ops exynos5_usb3phy_ops = {
> + .init = exynos5_usb3phy_init,
> + .exit = exynos5_usb3phy_exit,
> + .power_on = exynos5_usb3phy_power_on,
> + .power_off = exynos5_usb3phy_power_off,
> + .owner = THIS_MODULE,
> +};
> +
> +const struct usb3phy_config exynos5_usb3phy_cfg[] = {
> + {
> + .id = EXYNOS5_USB3PHY_UTMI,
This should be USB2 no?
> + .reg_pmu_offset = EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET,
> + .phy_isol = exynos5_usb3phy_isol,
> + },
> + {
> + .id = EXYNOS5_USB3PHY_PIPE3,
> + .reg_pmu_offset = EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET,
> + .phy_isol = exynos5_usb3phy_isol,
> + },
> + {},
> +};
> +
> +const struct exynos5_usb3phy_drv_data exynos5420_usb3phy = {
> + .has_usb30_sclk = true,
> + .has_multi_controller = true,
> + .phy_cfg = exynos5_usb3phy_cfg,
> +};
> +
> +const struct exynos5_usb3phy_drv_data exynos5250_usb3phy = {
> + .has_usb30_sclk = false,
> + .has_multi_controller = false,
> + .phy_cfg = exynos5_usb3phy_cfg,
> +};
> +
> +static const struct of_device_id exynos5_usb3phy_of_match[] = {
> + {
> + .compatible = "samsung,exynos5250-usb3phy",
> + .data = &exynos5250_usb3phy
> + }, {
> + .compatible = "samsung,exynos5420-usb3phy",
> + .data = &exynos5420_usb3phy
> + },
> + { },
> +};
> +
> +static int exynos5_usb3phy_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct device_node *node = dev->of_node;
> + struct exynos5_usb3phy_driver *drv;
> + struct phy_provider *phy_provider;
> + struct resource *res;
> + struct clk *clk;
> + const struct of_device_id *match;
> + const struct exynos5_usb3phy_drv_data *drv_data;
> + struct regmap *reg_isol;
> + int i;
> +
> + /*
> + * Exynos systems are completely DT enabled,
> + * so lets not have any platform data support for this driver.
> + */
Then you should add depend on OF for this driver.
> + if (!node) {
> + dev_err(dev, "no device node found\n");
> + return -ENODEV;
> + }
> +
> + match = of_match_node(exynos5_usb3phy_of_match, pdev->dev.of_node);
> + if (!match) {
> + dev_err(dev, "of_match_node() failed\n");
> + return -EINVAL;
> + }
> + drv_data = match->data;
> +
> + drv = devm_kzalloc(dev, sizeof(*drv), GFP_KERNEL);
> + if (!drv) {
> + dev_err(dev, "Failed to allocate memory\n");
dev_err is not needed here.
> + return -ENOMEM;
> + }
> +
> + dev_set_drvdata(dev, drv);
> + drv->dev = dev;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + drv->reg_phy = devm_ioremap_resource(dev, res);
> + if (IS_ERR(drv->reg_phy)) {
> + dev_err(dev, "Failed to map register memory (phy)\n");
> + return PTR_ERR(drv->reg_phy);
> + }
> +
> + drv->drv_data = drv_data;
> +
> + /*
> + * Exynos5420 SoC has multiple channels for USB 3.0 PHY, with
> + * each having separate power control registers.
> + * 'drv->channel' facilitates to set such registers.
> + */
> + if (drv->drv_data->has_multi_controller) {
> + drv->channel = of_alias_get_id(node, "usb3phy");
> + if (drv->channel < 0) {
> + dev_err(dev, "Invalid usb3drd phy node\n");
> + return -EINVAL;
> + }
> + }
> +
> + drv->clk = devm_clk_get(dev, "phy");
> + if (IS_ERR(drv->clk)) {
> + dev_err(dev, "Failed to get clock of phy controller\n");
> + return PTR_ERR(drv->clk);
> + }
> +
> + /*
> + * Exysno5420 SoC has an additional special clock, used for
> + * for USB 3.0 PHY operation, this clock goes to the PHY block
> + * as a reference clock to clock generation block of the controller,
> + * named as 'USB30_SCLK_100M'.
> + */
> + if (drv_data->has_usb30_sclk) {
> + drv->usb30_sclk = devm_clk_get(dev, "usb30_sclk_100m");
> + if (IS_ERR(drv->usb30_sclk)) {
> + dev_err(dev, "Failed to get phy reference clock\n");
> + return PTR_ERR(drv->usb30_sclk);
> + }
> + }
> +
> + clk = clk_get(dev, "usb3phy_refclk");
> + if (IS_ERR(clk)) {
> + dev_err(dev, "Failed to get reference clock of usb3drd phy\n");
> + return PTR_ERR(clk);
> + }
> + drv->rate = clk_get_rate(clk);
> + clk_put(clk);
> +
> + dev_dbg(dev, "Creating usb3drd phy\n");
dev_vdbg?
Cheers
Kishon
Hi Kishon,
On Mon, Jan 27, 2014 at 2:27 PM, Kishon Vijay Abraham I <[email protected]> wrote:
> Hi,
Thanks for review. Please find my answers inline below.
>
> On Monday 20 January 2014 07:12 PM, Vivek Gautam wrote:
>> Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
>> The new driver uses the generic PHY framework and will interact
>> with DWC3 controller present on Exynos5 series of SoCs.
>> Thereby, removing old phy-samsung-usb3 driver and related code
>> used untill now which was based on usb/phy framework.
>>
>> Signed-off-by: Vivek Gautam <[email protected]>
>> ---
>>
>> Changes from v2:
>> 1) Added support for multiple PHYs (UTMI+ and PIPE3) and
>> related changes in the driver structuring.
>> 2) Added a xlate function to get the required phy out of
>> number of PHYs in mutiple PHY scenerio.
>> 3) Changed the names of few structures and variables to
>> have a clearer meaning.
>> 4) Added 'usb3phy_config' structure to take care of mutiple
>> phys for a SoC having 'exynos5_usb3phy_drv_data' driver data.
>> 5) Not deleting support for old driver 'phy-samsung-usb3' until
>> required support for generic phy is added to DWC3.
>>
>> .../devicetree/bindings/phy/samsung-phy.txt | 49 ++
>> drivers/phy/Kconfig | 8 +
>> drivers/phy/Makefile | 1 +
>> drivers/phy/phy-exynos5-usb3.c | 621 ++++++++++++++++++++
>> 4 files changed, 679 insertions(+)
>> create mode 100644 drivers/phy/phy-exynos5-usb3.c
[snip]
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index 330ef2d..32f9f38 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -51,4 +51,12 @@ config PHY_EXYNOS_DP_VIDEO
>> help
>> Support for Display Port PHY found on Samsung EXYNOS SoCs.
>>
>> +config PHY_EXYNOS5_USB3
>> + tristate "Exynos5 SoC series USB 3.0 PHY driver"
>> + depends on ARCH_EXYNOS5
>> + select GENERIC_PHY
>> + select MFD_SYSCON
>
> add depends on 'HAS_IOMEM'. Someone reported getting
> undefined reference to `devm_ioremap_resource' with it.
Ok will add it.
>> + help
>> + Enable USB 3.0 PHY support for Exynos 5 SoC series
>> +
>> endmenu
[snip]
>> diff --git a/drivers/phy/phy-exynos5-usb3.c b/drivers/phy/phy-exynos5-usb3.c
>> new file mode 100644
>> index 0000000..24efed0
>> --- /dev/null
>> +++ b/drivers/phy/phy-exynos5-usb3.c
>> @@ -0,0 +1,621 @@
>> +/*
>> + * Samsung EXYNOS5 SoC series USB 3.0 PHY driver
>> + *
>> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
>> + * Author: Vivek Gautam <[email protected]>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + */
>> +
>> +#include <linux/clk.h>
>> +#include <linux/delay.h>
>> +#include <linux/io.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/of_address.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/mutex.h>
>> +#include <linux/mfd/syscon.h>
>> +#include <linux/regmap.h>
>> +
>> +/* Exynos USB PHY registers */
>> +#define EXYNOS5_FSEL_9MHZ6 0x0
>> +#define EXYNOS5_FSEL_10MHZ 0x1
>> +#define EXYNOS5_FSEL_12MHZ 0x2
>> +#define EXYNOS5_FSEL_19MHZ2 0x3
>> +#define EXYNOS5_FSEL_20MHZ 0x4
>> +#define EXYNOS5_FSEL_24MHZ 0x5
>> +#define EXYNOS5_FSEL_50MHZ 0x7
>> +
>> +/* EXYNOS5: USB 3.0 DRD PHY registers */
>> +#define EXYNOS5_DRD_LINKSYSTEM (0x04)
>> +
>> +#define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
>> +#define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
>> +#define LINKSYSTEM_XHCI_VERSION_CONTROL (0x1 << 27)
>> +
>> +#define EXYNOS5_DRD_PHYUTMI (0x08)
>> +
>> +#define PHYUTMI_OTGDISABLE (0x1 << 6)
>> +#define PHYUTMI_FORCESUSPEND (0x1 << 1)
>> +#define PHYUTMI_FORCESLEEP (0x1 << 0)
>
> use BIT macro here and below?
Ok.
>> +
>> +#define EXYNOS5_DRD_PHYPIPE (0x0c)
>> +
>> +#define EXYNOS5_DRD_PHYCLKRST (0x10)
>> +
>> +#define PHYCLKRST_EN_UTMISUSPEND (0x1 << 31)
>> +
>> +#define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23)
>> +#define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23)
>> +
>> +#define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21)
>> +#define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21)
>> +
>> +#define PHYCLKRST_SSC_EN (0x1 << 20)
>> +#define PHYCLKRST_REF_SSP_EN (0x1 << 19)
>> +#define PHYCLKRST_REF_CLKDIV2 (0x1 << 18)
>> +
>> +#define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11)
>> +#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11)
>> +#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x32 << 11)
>> +#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11)
>> +#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11)
>> +#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
>> +
>> +#define PHYCLKRST_FSEL_MASK (0x3f << 5)
>> +#define PHYCLKRST_FSEL(_x) ((_x) << 5)
>> +#define PHYCLKRST_FSEL_PAD_100MHZ (0x27 << 5)
>> +#define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5)
>> +#define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5)
>> +#define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5)
>> +
>> +#define PHYCLKRST_RETENABLEN (0x1 << 4)
>> +
>> +#define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2)
>> +#define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2)
>> +#define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2)
>> +
>> +#define PHYCLKRST_PORTRESET (0x1 << 1)
>> +#define PHYCLKRST_COMMONONN (0x1 << 0)
>> +
>> +#define EXYNOS5_DRD_PHYREG0 (0x14)
>> +#define EXYNOS5_DRD_PHYREG1 (0x18)
>> +
>> +#define EXYNOS5_DRD_PHYPARAM0 (0x1c)
>> +
>> +#define PHYPARAM0_REF_USE_PAD (0x1 << 31)
>> +#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26)
>> +#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26)
>> +
>> +#define EXYNOS5_DRD_PHYPARAM1 (0x20)
>> +
>> +#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
>> +#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
>> +
>> +#define EXYNOS5_DRD_PHYTERM (0x24)
>> +
>> +#define EXYNOS5_DRD_PHYTEST (0x28)
>> +
>> +#define PHYTEST_POWERDOWN_SSP (0x1 << 3)
>> +#define PHYTEST_POWERDOWN_HSP (0x1 << 2)
>> +
>> +#define EXYNOS5_DRD_PHYADP (0x2c)
>> +
>> +#define EXYNOS5_DRD_PHYBATCHG (0x30)
>> +
>> +#define PHYBATCHG_UTMI_CLKSEL (0x1 << 2)
>> +
>> +#define EXYNOS5_DRD_PHYRESUME (0x34)
>> +#define EXYNOS5_DRD_LINKPORT (0x44)
>> +
>> +/* Power isolation defined in power management unit */
>> +#define EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET (0x704)
>> +#define EXYNOS5_USB3DRD_PMU_ISOL (1 << 0)
>> +
>> +#define KHZ 1000
>> +#define MHZ (KHZ * KHZ)
>> +
>> +enum exynos5_usb3phy_id {
>> + EXYNOS5_USB3PHY_UTMI,
>> + EXYNOS5_USB3PHY_PIPE3,
>> + EXYNOS5_USB3PHYS_NUM,
>> +};
>> +
>> +struct usb3phy_config {
>> + u32 id;
>> + u32 reg_pmu_offset;
>> + void (*phy_isol)(struct phy *phy, u32 on);
>> +};
>> +
>> +struct exynos5_usb3phy_drv_data {
>> + bool has_usb30_sclk;
>> + bool has_multi_controller;
>> + const struct usb3phy_config *phy_cfg;
>> +};
>> +
>> +/**
>> + * struct exynos5_usb3phy_driver - driver data for USB 3.0 PHY
>
> Is this really a driver data? I think it should be just exynos5_usb3phy.
Yes, not a driver data, rather just 'exynos_usb3phy' structure. will
modify the name
>> + * @dev: pointer to device instance of this platform device
>> + * @reg_phy: usb phy controller register memory base
>> + * @clk: phy clock for register access
>> + * @usb30_sclk: additional special clock for phy operations
>> + * @drv_data: pointer to SoC level driver data structure
>> + * @phys[]: array for 'EXYNOS5_USB3PHYS_NUM' number of PHY
>> + * instances each with its 'phy' and 'phy_cfg'.
>> + * @extrefclk: frequency select settings when using 'separate
>> + * reference clocks' for SS and HS operations
>> + * @rate: rate of reference clock to PHY block
>> + * @channel: number of PHY channels present in SoC
>> + */
>> +struct exynos5_usb3phy_driver {
>> + struct device *dev;
>> + void __iomem *reg_phy;
>> + struct clk *clk;
>> + struct clk *usb30_sclk;
>> + const struct exynos5_usb3phy_drv_data *drv_data;
>> + struct phy_usb_instance {
>> + struct phy *phy;
>> + u32 index;
>> + struct regmap *reg_isol;
>> + const struct usb3phy_config *phy_cfg;
>> + } phys[EXYNOS5_USB3PHYS_NUM];
>> + u32 extrefclk;
>> + unsigned long rate;
>> + u32 channel;
>> +};
>> +
>> +#define to_usb3phy_driver(inst) \
>> + container_of((inst), struct exynos5_usb3phy_driver, \
>> + phys[(inst)->index]);
>> +
>> +/*
>> + * exynos5_rate_to_clk() converts the supplied clock rate to the value that
>> + * can be written to the phy register.
>> + */
>> +static u32 exynos5_rate_to_clk(unsigned long rate)
>> +{
>> + unsigned int clksel;
>> +
>> + /* EXYNOS5_FSEL_MASK */
>> +
>> + switch (rate) {
>> + case 9600 * KHZ:
>> + clksel = EXYNOS5_FSEL_9MHZ6;
>> + break;
>> + case 10 * MHZ:
>> + clksel = EXYNOS5_FSEL_10MHZ;
>> + break;
>> + case 12 * MHZ:
>> + clksel = EXYNOS5_FSEL_12MHZ;
>> + break;
>> + case 19200 * KHZ:
>> + clksel = EXYNOS5_FSEL_19MHZ2;
>> + break;
>> + case 20 * MHZ:
>> + clksel = EXYNOS5_FSEL_20MHZ;
>> + break;
>> + case 24 * MHZ:
>> + clksel = EXYNOS5_FSEL_24MHZ;
>> + break;
>> + case 50 * MHZ:
>> + clksel = EXYNOS5_FSEL_50MHZ;
>> + break;
>> + default:
>> + clksel = -EINVAL;
>> + }
>> +
>> + return clksel;
>> +}
>> +
>> +static void exynos5_usb3phy_isol(struct phy *phy, unsigned int on)
>> +{
>> + u32 pmu_offset;
>> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
>> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
>> +
>> + pmu_offset = inst->phy_cfg->reg_pmu_offset;
>> + if (!inst->reg_isol)
>> + return;
>> +
>> + switch (drv->channel) {
>> + case 1:
>> + /* Channel 1 is at 0x708 offset */
>> + pmu_offset += sizeof(&pmu_offset);
>> + break;
>> + case 0:
>> + default:
>> + /* Channel 0 is at 0x704 offset */
>> + break;
>> + }
>
> This can be in a simple 'if' stmt no?
What if there are systems with more channels? In that case also we
will have to fall back to a switch-case statement ?
>> +
>> + regmap_update_bits(inst->reg_isol, pmu_offset,
>> + EXYNOS5_USB3DRD_PMU_ISOL, ~on);
>> +}
>> +
>> +/*
>> + * Sets the phy clk as EXTREFCLK (XXTI) which is internal clock from clock core.
>> + */
>> +static u32 exynos5_usb3phy_set_refclk(struct exynos5_usb3phy_driver *drv)
>> +{
>> + u32 reg;
>> +
>> + reg = PHYCLKRST_REFCLKSEL_EXT_REFCLK |
>> + PHYCLKRST_FSEL(drv->extrefclk);
>> +
>> + switch (drv->extrefclk) {
>> + case EXYNOS5_FSEL_50MHZ:
>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
>> + PHYCLKRST_SSC_REFCLKSEL(0x00));
>> + break;
>> + case EXYNOS5_FSEL_24MHZ:
>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
>> + PHYCLKRST_SSC_REFCLKSEL(0x88));
>> + break;
>> + case EXYNOS5_FSEL_20MHZ:
>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
>> + PHYCLKRST_SSC_REFCLKSEL(0x00));
>> + break;
>> + case EXYNOS5_FSEL_19MHZ2:
>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
>> + PHYCLKRST_SSC_REFCLKSEL(0x88));
>> + break;
>> + default:
>> + dev_dbg(drv->dev, "unsupported ref clk\n");
>> + break;
>> + }
>> +
>> + return reg;
>> +}
>> +
>> +static int exynos5_usb3phy_init(struct phy *phy)
>> +{
>> + int ret;
>> + u32 phyparam0;
>> + u32 phyparam1;
>> + u32 linksystem;
>> + u32 phybatchg;
>> + u32 phytest;
>> + u32 phyclkrst;
>
> instead you can define a single variable 'u32 reg' for register read and writes.
Right.
>> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
>> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
>> +
>> + ret = clk_prepare_enable(drv->clk);
>> + if (ret)
>> + return ret;
>> +
>> + drv->extrefclk = exynos5_rate_to_clk(drv->rate);
>> + if (drv->extrefclk == -EINVAL) {
>> + dev_err(drv->dev, "Clock rate (%ld) not supported\n",
>> + drv->rate);
>> + return -EINVAL;
>> + }
>> +
>> + /* Reset USB 3.0 PHY */
>> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYREG0);
>> +
>> + phyparam0 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
>> + /* Select PHY CLK source */
>> + phyparam0 &= ~PHYPARAM0_REF_USE_PAD;
>> + /* Set Loss-of-Signal Detector sensitivity */
>> + phyparam0 &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
>> + phyparam0 |= PHYPARAM0_REF_LOSLEVEL;
>> + writel(phyparam0, drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
>> +
>> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYRESUME);
>> +
>> + /*
>> + * Setting the Frame length Adj value[6:1] to default 0x20
>> + * See xHCI 1.0 spec, 5.2.4
>> + */
>> + linksystem = LINKSYSTEM_XHCI_VERSION_CONTROL |
>> + LINKSYSTEM_FLADJ(0x20);
>> + writel(linksystem, drv->reg_phy + EXYNOS5_DRD_LINKSYSTEM);
>> +
>> + phyparam1 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
>> + /* Set Tx De-Emphasis level */
>> + phyparam1 &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
>> + phyparam1 |= PHYPARAM1_PCS_TXDEEMPH;
>> + writel(phyparam1, drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
>> +
>> + phybatchg = readl(drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
>> + phybatchg |= PHYBATCHG_UTMI_CLKSEL;
>> + writel(phybatchg, drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
>> +
>> + /* PHYTEST POWERDOWN Control */
>> + phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
>> + phytest &= ~(PHYTEST_POWERDOWN_SSP |
>> + PHYTEST_POWERDOWN_HSP);
>> + writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
>> +
>> + /* UTMI Power Control */
>> + writel(PHYUTMI_OTGDISABLE, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
>
> All these UTMI configuration should be done in usb2 init.
Ok, will move this to separate function.
>> +
>> + phyclkrst = exynos5_usb3phy_set_refclk(drv);
>> +
>> + phyclkrst |= PHYCLKRST_PORTRESET |
>> + /* Digital power supply in normal operating mode */
>> + PHYCLKRST_RETENABLEN |
>> + /* Enable ref clock for SS function */
>> + PHYCLKRST_REF_SSP_EN |
>> + /* Enable spread spectrum */
>> + PHYCLKRST_SSC_EN |
>> + /* Power down HS Bias and PLL blocks in suspend mode */
>> + PHYCLKRST_COMMONONN;
>> +
>> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>> +
>> + udelay(10);
>> +
>> + phyclkrst &= ~PHYCLKRST_PORTRESET;
>> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>> +
>> + clk_disable_unprepare(drv->clk);
>> +
>> + return 0;
>> +}
>> +
>> +static int exynos5_usb3phy_exit(struct phy *phy)
>> +{
>> + int ret;
>> + u32 phyutmi;
>> + u32 phyclkrst;
>> + u32 phytest;
>
> same here..
right, will do it.
>> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
>> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
>> +
>> + ret = clk_prepare_enable(drv->clk);
>> + if (ret)
>> + return ret;
>> +
>> + phyutmi = PHYUTMI_OTGDISABLE |
>> + PHYUTMI_FORCESUSPEND |
>> + PHYUTMI_FORCESLEEP;
>> + writel(phyutmi, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
>
> here too.. UTMI configuration should be part of USB2.
ok.
>> +
[snip]
>> +
>> +static struct phy_ops exynos5_usb3phy_ops = {
>> + .init = exynos5_usb3phy_init,
>> + .exit = exynos5_usb3phy_exit,
>> + .power_on = exynos5_usb3phy_power_on,
>> + .power_off = exynos5_usb3phy_power_off,
>> + .owner = THIS_MODULE,
>> +};
>> +
>> +const struct usb3phy_config exynos5_usb3phy_cfg[] = {
>> + {
>> + .id = EXYNOS5_USB3PHY_UTMI,
>
> This should be USB2 no?
Actually the thought was to have similar naming for enums.
EXYNOS5_USB3PHY_UTMI
EXYNOS5_USB3PHY_PIPE3
Since the entire driver was going that way.
But will change these to a more common name
EXYNOS5_DRDPHY_UTMI
EXYNOS5_DRDPHY_PIPE3,
in the same fashion the register names are defined.
Will that be fine ?
>> + .reg_pmu_offset = EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET,
>> + .phy_isol = exynos5_usb3phy_isol,
>> + },
>> + {
>> + .id = EXYNOS5_USB3PHY_PIPE3,
>> + .reg_pmu_offset = EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET,
>> + .phy_isol = exynos5_usb3phy_isol,
>> + },
>> + {},
>> +};
>> +
>> +const struct exynos5_usb3phy_drv_data exynos5420_usb3phy = {
>> + .has_usb30_sclk = true,
>> + .has_multi_controller = true,
>> + .phy_cfg = exynos5_usb3phy_cfg,
>> +};
>> +
>> +const struct exynos5_usb3phy_drv_data exynos5250_usb3phy = {
>> + .has_usb30_sclk = false,
>> + .has_multi_controller = false,
>> + .phy_cfg = exynos5_usb3phy_cfg,
>> +};
>> +
>> +static const struct of_device_id exynos5_usb3phy_of_match[] = {
>> + {
>> + .compatible = "samsung,exynos5250-usb3phy",
>> + .data = &exynos5250_usb3phy
>> + }, {
>> + .compatible = "samsung,exynos5420-usb3phy",
>> + .data = &exynos5420_usb3phy
>> + },
>> + { },
>> +};
>> +
>> +static int exynos5_usb3phy_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct device_node *node = dev->of_node;
>> + struct exynos5_usb3phy_driver *drv;
>> + struct phy_provider *phy_provider;
>> + struct resource *res;
>> + struct clk *clk;
>> + const struct of_device_id *match;
>> + const struct exynos5_usb3phy_drv_data *drv_data;
>> + struct regmap *reg_isol;
>> + int i;
>> +
>> + /*
>> + * Exynos systems are completely DT enabled,
>> + * so lets not have any platform data support for this driver.
>> + */
>
> Then you should add depend on OF for this driver.
Right. depends on CONFIG_OF. Will add one.
>> + if (!node) {
>> + dev_err(dev, "no device node found\n");
>> + return -ENODEV;
>> + }
>> +
>> + match = of_match_node(exynos5_usb3phy_of_match, pdev->dev.of_node);
>> + if (!match) {
>> + dev_err(dev, "of_match_node() failed\n");
>> + return -EINVAL;
>> + }
>> + drv_data = match->data;
>> +
>> + drv = devm_kzalloc(dev, sizeof(*drv), GFP_KERNEL);
>> + if (!drv) {
>> + dev_err(dev, "Failed to allocate memory\n");
>
> dev_err is not needed here.
Right, will remove it.
>> + return -ENOMEM;
>> + }
>> +
[snip]
>> + dev_dbg(dev, "Creating usb3drd phy\n");
> dev_vdbg?
Sure.
>
> Cheers
> Kishon
> --
> To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
Best Regards
Vivek Gautam
Samsung R&D Institute, Bangalore
India
Hi,
On Thursday 30 January 2014 09:49 AM, Vivek Gautam wrote:
> Hi Kishon,
>
>
> On Mon, Jan 27, 2014 at 2:27 PM, Kishon Vijay Abraham I <[email protected]> wrote:
>> Hi,
>
> Thanks for review. Please find my answers inline below.
>
>>
>> On Monday 20 January 2014 07:12 PM, Vivek Gautam wrote:
>>> Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
>>> The new driver uses the generic PHY framework and will interact
>>> with DWC3 controller present on Exynos5 series of SoCs.
>>> Thereby, removing old phy-samsung-usb3 driver and related code
>>> used untill now which was based on usb/phy framework.
>>>
>>> Signed-off-by: Vivek Gautam <[email protected]>
>>> ---
>>>
>>> Changes from v2:
>>> 1) Added support for multiple PHYs (UTMI+ and PIPE3) and
>>> related changes in the driver structuring.
>>> 2) Added a xlate function to get the required phy out of
>>> number of PHYs in mutiple PHY scenerio.
>>> 3) Changed the names of few structures and variables to
>>> have a clearer meaning.
>>> 4) Added 'usb3phy_config' structure to take care of mutiple
>>> phys for a SoC having 'exynos5_usb3phy_drv_data' driver data.
>>> 5) Not deleting support for old driver 'phy-samsung-usb3' until
>>> required support for generic phy is added to DWC3.
>>>
>>> .../devicetree/bindings/phy/samsung-phy.txt | 49 ++
>>> drivers/phy/Kconfig | 8 +
>>> drivers/phy/Makefile | 1 +
>>> drivers/phy/phy-exynos5-usb3.c | 621 ++++++++++++++++++++
>>> 4 files changed, 679 insertions(+)
>>> create mode 100644 drivers/phy/phy-exynos5-usb3.c
> [snip]
>
>>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>>> index 330ef2d..32f9f38 100644
>>> --- a/drivers/phy/Kconfig
>>> +++ b/drivers/phy/Kconfig
>>> @@ -51,4 +51,12 @@ config PHY_EXYNOS_DP_VIDEO
>>> help
>>> Support for Display Port PHY found on Samsung EXYNOS SoCs.
>>>
>>> +config PHY_EXYNOS5_USB3
This shouldn't be USB3 since this driver has support for both USB2 and USB3.
maybe just PHY_EXYNOS5_USB?
>>> + tristate "Exynos5 SoC series USB 3.0 PHY driver"
>>> + depends on ARCH_EXYNOS5
>>> + select GENERIC_PHY
>>> + select MFD_SYSCON
>>
>> add depends on 'HAS_IOMEM'. Someone reported getting
>> undefined reference to `devm_ioremap_resource' with it.
>
> Ok will add it.
>
>>> + help
>>> + Enable USB 3.0 PHY support for Exynos 5 SoC series
>>> +
>>> endmenu
> [snip]
>
>>> diff --git a/drivers/phy/phy-exynos5-usb3.c b/drivers/phy/phy-exynos5-usb3.c
>>> new file mode 100644
>>> index 0000000..24efed0
>>> --- /dev/null
>>> +++ b/drivers/phy/phy-exynos5-usb3.c
>>> @@ -0,0 +1,621 @@
>>> +/*
>>> + * Samsung EXYNOS5 SoC series USB 3.0 PHY driver
>>> + *
>>> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
>>> + * Author: Vivek Gautam <[email protected]>
>>> + *
>>> + * This program is free software; you can redistribute it and/or modify
>>> + * it under the terms of the GNU General Public License version 2 as
>>> + * published by the Free Software Foundation.
>>> + */
>>> +
>>> +#include <linux/clk.h>
>>> +#include <linux/delay.h>
>>> +#include <linux/io.h>
>>> +#include <linux/kernel.h>
>>> +#include <linux/module.h>
>>> +#include <linux/of.h>
>>> +#include <linux/of_address.h>
>>> +#include <linux/phy/phy.h>
>>> +#include <linux/platform_device.h>
>>> +#include <linux/mutex.h>
>>> +#include <linux/mfd/syscon.h>
>>> +#include <linux/regmap.h>
>>> +
>>> +/* Exynos USB PHY registers */
>>> +#define EXYNOS5_FSEL_9MHZ6 0x0
>>> +#define EXYNOS5_FSEL_10MHZ 0x1
>>> +#define EXYNOS5_FSEL_12MHZ 0x2
>>> +#define EXYNOS5_FSEL_19MHZ2 0x3
>>> +#define EXYNOS5_FSEL_20MHZ 0x4
>>> +#define EXYNOS5_FSEL_24MHZ 0x5
>>> +#define EXYNOS5_FSEL_50MHZ 0x7
>>> +
>>> +/* EXYNOS5: USB 3.0 DRD PHY registers */
>>> +#define EXYNOS5_DRD_LINKSYSTEM (0x04)
>>> +
>>> +#define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
>>> +#define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
>>> +#define LINKSYSTEM_XHCI_VERSION_CONTROL (0x1 << 27)
>>> +
>>> +#define EXYNOS5_DRD_PHYUTMI (0x08)
>>> +
>>> +#define PHYUTMI_OTGDISABLE (0x1 << 6)
>>> +#define PHYUTMI_FORCESUSPEND (0x1 << 1)
>>> +#define PHYUTMI_FORCESLEEP (0x1 << 0)
>>
>> use BIT macro here and below?
>
> Ok.
>
>>> +
>>> +#define EXYNOS5_DRD_PHYPIPE (0x0c)
>>> +
>>> +#define EXYNOS5_DRD_PHYCLKRST (0x10)
>>> +
>>> +#define PHYCLKRST_EN_UTMISUSPEND (0x1 << 31)
>>> +
>>> +#define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23)
>>> +#define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23)
>>> +
>>> +#define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21)
>>> +#define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21)
>>> +
>>> +#define PHYCLKRST_SSC_EN (0x1 << 20)
>>> +#define PHYCLKRST_REF_SSP_EN (0x1 << 19)
>>> +#define PHYCLKRST_REF_CLKDIV2 (0x1 << 18)
>>> +
>>> +#define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11)
>>> +#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11)
>>> +#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x32 << 11)
>>> +#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11)
>>> +#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11)
>>> +#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
>>> +
>>> +#define PHYCLKRST_FSEL_MASK (0x3f << 5)
>>> +#define PHYCLKRST_FSEL(_x) ((_x) << 5)
>>> +#define PHYCLKRST_FSEL_PAD_100MHZ (0x27 << 5)
>>> +#define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5)
>>> +#define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5)
>>> +#define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5)
>>> +
>>> +#define PHYCLKRST_RETENABLEN (0x1 << 4)
>>> +
>>> +#define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2)
>>> +#define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2)
>>> +#define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2)
>>> +
>>> +#define PHYCLKRST_PORTRESET (0x1 << 1)
>>> +#define PHYCLKRST_COMMONONN (0x1 << 0)
>>> +
>>> +#define EXYNOS5_DRD_PHYREG0 (0x14)
>>> +#define EXYNOS5_DRD_PHYREG1 (0x18)
>>> +
>>> +#define EXYNOS5_DRD_PHYPARAM0 (0x1c)
>>> +
>>> +#define PHYPARAM0_REF_USE_PAD (0x1 << 31)
>>> +#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26)
>>> +#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26)
>>> +
>>> +#define EXYNOS5_DRD_PHYPARAM1 (0x20)
>>> +
>>> +#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
>>> +#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
>>> +
>>> +#define EXYNOS5_DRD_PHYTERM (0x24)
>>> +
>>> +#define EXYNOS5_DRD_PHYTEST (0x28)
>>> +
>>> +#define PHYTEST_POWERDOWN_SSP (0x1 << 3)
>>> +#define PHYTEST_POWERDOWN_HSP (0x1 << 2)
>>> +
>>> +#define EXYNOS5_DRD_PHYADP (0x2c)
>>> +
>>> +#define EXYNOS5_DRD_PHYBATCHG (0x30)
>>> +
>>> +#define PHYBATCHG_UTMI_CLKSEL (0x1 << 2)
>>> +
>>> +#define EXYNOS5_DRD_PHYRESUME (0x34)
>>> +#define EXYNOS5_DRD_LINKPORT (0x44)
>>> +
>>> +/* Power isolation defined in power management unit */
>>> +#define EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET (0x704)
>>> +#define EXYNOS5_USB3DRD_PMU_ISOL (1 << 0)
>>> +
>>> +#define KHZ 1000
>>> +#define MHZ (KHZ * KHZ)
>>> +
>>> +enum exynos5_usb3phy_id {
>>> + EXYNOS5_USB3PHY_UTMI,
>>> + EXYNOS5_USB3PHY_PIPE3,
>>> + EXYNOS5_USB3PHYS_NUM,
>>> +};
here and all the structure names below shouldn't have usb3 in their names since
this is not just a 'usb3' phy driver..
>>> +
>>> +struct usb3phy_config {
>>> + u32 id;
>>> + u32 reg_pmu_offset;
>>> + void (*phy_isol)(struct phy *phy, u32 on);
>>> +};
>>> +
>>> +struct exynos5_usb3phy_drv_data {
>>> + bool has_usb30_sclk;
>>> + bool has_multi_controller;
>>> + const struct usb3phy_config *phy_cfg;
>>> +};
>>> +
>>> +/**
>>> + * struct exynos5_usb3phy_driver - driver data for USB 3.0 PHY
>>
>> Is this really a driver data? I think it should be just exynos5_usb3phy.
> Yes, not a driver data, rather just 'exynos_usb3phy' structure. will
> modify the name
>
>>> + * @dev: pointer to device instance of this platform device
>>> + * @reg_phy: usb phy controller register memory base
>>> + * @clk: phy clock for register access
>>> + * @usb30_sclk: additional special clock for phy operations
>>> + * @drv_data: pointer to SoC level driver data structure
>>> + * @phys[]: array for 'EXYNOS5_USB3PHYS_NUM' number of PHY
>>> + * instances each with its 'phy' and 'phy_cfg'.
>>> + * @extrefclk: frequency select settings when using 'separate
>>> + * reference clocks' for SS and HS operations
>>> + * @rate: rate of reference clock to PHY block
>>> + * @channel: number of PHY channels present in SoC
>>> + */
>>> +struct exynos5_usb3phy_driver {
>>> + struct device *dev;
>>> + void __iomem *reg_phy;
>>> + struct clk *clk;
>>> + struct clk *usb30_sclk;
>>> + const struct exynos5_usb3phy_drv_data *drv_data;
>>> + struct phy_usb_instance {
>>> + struct phy *phy;
>>> + u32 index;
>>> + struct regmap *reg_isol;
>>> + const struct usb3phy_config *phy_cfg;
>>> + } phys[EXYNOS5_USB3PHYS_NUM];
>>> + u32 extrefclk;
>>> + unsigned long rate;
>>> + u32 channel;
>>> +};
>>> +
>>> +#define to_usb3phy_driver(inst) \
>>> + container_of((inst), struct exynos5_usb3phy_driver, \
>>> + phys[(inst)->index]);
>>> +
>>> +/*
>>> + * exynos5_rate_to_clk() converts the supplied clock rate to the value that
>>> + * can be written to the phy register.
>>> + */
>>> +static u32 exynos5_rate_to_clk(unsigned long rate)
>>> +{
>>> + unsigned int clksel;
>>> +
>>> + /* EXYNOS5_FSEL_MASK */
>>> +
>>> + switch (rate) {
>>> + case 9600 * KHZ:
>>> + clksel = EXYNOS5_FSEL_9MHZ6;
>>> + break;
>>> + case 10 * MHZ:
>>> + clksel = EXYNOS5_FSEL_10MHZ;
>>> + break;
>>> + case 12 * MHZ:
>>> + clksel = EXYNOS5_FSEL_12MHZ;
>>> + break;
>>> + case 19200 * KHZ:
>>> + clksel = EXYNOS5_FSEL_19MHZ2;
>>> + break;
>>> + case 20 * MHZ:
>>> + clksel = EXYNOS5_FSEL_20MHZ;
>>> + break;
>>> + case 24 * MHZ:
>>> + clksel = EXYNOS5_FSEL_24MHZ;
>>> + break;
>>> + case 50 * MHZ:
>>> + clksel = EXYNOS5_FSEL_50MHZ;
>>> + break;
>>> + default:
>>> + clksel = -EINVAL;
>>> + }
>>> +
>>> + return clksel;
>>> +}
>>> +
>>> +static void exynos5_usb3phy_isol(struct phy *phy, unsigned int on)
>>> +{
>>> + u32 pmu_offset;
>>> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
>>> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
>>> +
>>> + pmu_offset = inst->phy_cfg->reg_pmu_offset;
>>> + if (!inst->reg_isol)
>>> + return;
>>> +
>>> + switch (drv->channel) {
>>> + case 1:
>>> + /* Channel 1 is at 0x708 offset */
>>> + pmu_offset += sizeof(&pmu_offset);
>>> + break;
>>> + case 0:
>>> + default:
>>> + /* Channel 0 is at 0x704 offset */
>>> + break;
>>> + }
>>
>> This can be in a simple 'if' stmt no?
> What if there are systems with more channels? In that case also we
> will have to fall back to a switch-case statement ?
right.
>
>>> +
>>> + regmap_update_bits(inst->reg_isol, pmu_offset,
>>> + EXYNOS5_USB3DRD_PMU_ISOL, ~on);
>>> +}
>>> +
>>> +/*
>>> + * Sets the phy clk as EXTREFCLK (XXTI) which is internal clock from clock core.
>>> + */
>>> +static u32 exynos5_usb3phy_set_refclk(struct exynos5_usb3phy_driver *drv)
>>> +{
>>> + u32 reg;
>>> +
>>> + reg = PHYCLKRST_REFCLKSEL_EXT_REFCLK |
>>> + PHYCLKRST_FSEL(drv->extrefclk);
>>> +
>>> + switch (drv->extrefclk) {
>>> + case EXYNOS5_FSEL_50MHZ:
>>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
>>> + PHYCLKRST_SSC_REFCLKSEL(0x00));
>>> + break;
>>> + case EXYNOS5_FSEL_24MHZ:
>>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
>>> + PHYCLKRST_SSC_REFCLKSEL(0x88));
>>> + break;
>>> + case EXYNOS5_FSEL_20MHZ:
>>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
>>> + PHYCLKRST_SSC_REFCLKSEL(0x00));
>>> + break;
>>> + case EXYNOS5_FSEL_19MHZ2:
>>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
>>> + PHYCLKRST_SSC_REFCLKSEL(0x88));
>>> + break;
>>> + default:
>>> + dev_dbg(drv->dev, "unsupported ref clk\n");
>>> + break;
>>> + }
>>> +
>>> + return reg;
>>> +}
>>> +
>>> +static int exynos5_usb3phy_init(struct phy *phy)
>>> +{
>>> + int ret;
>>> + u32 phyparam0;
>>> + u32 phyparam1;
>>> + u32 linksystem;
>>> + u32 phybatchg;
>>> + u32 phytest;
>>> + u32 phyclkrst;
>>
>> instead you can define a single variable 'u32 reg' for register read and writes.
>
> Right.
>
>>> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
>>> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
>>> +
>>> + ret = clk_prepare_enable(drv->clk);
>>> + if (ret)
>>> + return ret;
>>> +
>>> + drv->extrefclk = exynos5_rate_to_clk(drv->rate);
>>> + if (drv->extrefclk == -EINVAL) {
>>> + dev_err(drv->dev, "Clock rate (%ld) not supported\n",
>>> + drv->rate);
>>> + return -EINVAL;
>>> + }
>>> +
>>> + /* Reset USB 3.0 PHY */
>>> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYREG0);
>>> +
>>> + phyparam0 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
>>> + /* Select PHY CLK source */
>>> + phyparam0 &= ~PHYPARAM0_REF_USE_PAD;
>>> + /* Set Loss-of-Signal Detector sensitivity */
>>> + phyparam0 &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
>>> + phyparam0 |= PHYPARAM0_REF_LOSLEVEL;
>>> + writel(phyparam0, drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
>>> +
>>> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYRESUME);
>>> +
>>> + /*
>>> + * Setting the Frame length Adj value[6:1] to default 0x20
>>> + * See xHCI 1.0 spec, 5.2.4
>>> + */
>>> + linksystem = LINKSYSTEM_XHCI_VERSION_CONTROL |
>>> + LINKSYSTEM_FLADJ(0x20);
>>> + writel(linksystem, drv->reg_phy + EXYNOS5_DRD_LINKSYSTEM);
>>> +
>>> + phyparam1 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
>>> + /* Set Tx De-Emphasis level */
>>> + phyparam1 &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
>>> + phyparam1 |= PHYPARAM1_PCS_TXDEEMPH;
>>> + writel(phyparam1, drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
>>> +
>>> + phybatchg = readl(drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
>>> + phybatchg |= PHYBATCHG_UTMI_CLKSEL;
>>> + writel(phybatchg, drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
>>> +
>>> + /* PHYTEST POWERDOWN Control */
>>> + phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
>>> + phytest &= ~(PHYTEST_POWERDOWN_SSP |
>>> + PHYTEST_POWERDOWN_HSP);
>>> + writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
>>> +
>>> + /* UTMI Power Control */
>>> + writel(PHYUTMI_OTGDISABLE, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
>>
>> All these UTMI configuration should be done in usb2 init.
> Ok, will move this to separate function.
>
>>> +
>>> + phyclkrst = exynos5_usb3phy_set_refclk(drv);
>>> +
>>> + phyclkrst |= PHYCLKRST_PORTRESET |
>>> + /* Digital power supply in normal operating mode */
>>> + PHYCLKRST_RETENABLEN |
>>> + /* Enable ref clock for SS function */
>>> + PHYCLKRST_REF_SSP_EN |
>>> + /* Enable spread spectrum */
>>> + PHYCLKRST_SSC_EN |
>>> + /* Power down HS Bias and PLL blocks in suspend mode */
>>> + PHYCLKRST_COMMONONN;
>>> +
>>> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>>> +
>>> + udelay(10);
>>> +
>>> + phyclkrst &= ~PHYCLKRST_PORTRESET;
>>> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>>> +
>>> + clk_disable_unprepare(drv->clk);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int exynos5_usb3phy_exit(struct phy *phy)
>>> +{
>>> + int ret;
>>> + u32 phyutmi;
>>> + u32 phyclkrst;
>>> + u32 phytest;
>>
>> same here..
> right, will do it.
>
>>> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
>>> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
>>> +
>>> + ret = clk_prepare_enable(drv->clk);
>>> + if (ret)
>>> + return ret;
>>> +
>>> + phyutmi = PHYUTMI_OTGDISABLE |
>>> + PHYUTMI_FORCESUSPEND |
>>> + PHYUTMI_FORCESLEEP;
>>> + writel(phyutmi, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
>>
>> here too.. UTMI configuration should be part of USB2.
> ok.
>
>>> +
> [snip]
>
>>> +
>>> +static struct phy_ops exynos5_usb3phy_ops = {
>>> + .init = exynos5_usb3phy_init,
>>> + .exit = exynos5_usb3phy_exit,
>>> + .power_on = exynos5_usb3phy_power_on,
>>> + .power_off = exynos5_usb3phy_power_off,
>>> + .owner = THIS_MODULE,
>>> +};
>>> +
>>> +const struct usb3phy_config exynos5_usb3phy_cfg[] = {
>>> + {
>>> + .id = EXYNOS5_USB3PHY_UTMI,
>>
>> This should be USB2 no?
> Actually the thought was to have similar naming for enums.
> EXYNOS5_USB3PHY_UTMI
> EXYNOS5_USB3PHY_PIPE3
>
> Since the entire driver was going that way.
> But will change these to a more common name
> EXYNOS5_DRDPHY_UTMI
> EXYNOS5_DRDPHY_PIPE3,
> in the same fashion the register names are defined.
> Will that be fine ?
Yeah.
Thanks
Kishon
Hi,
On Thu, Jan 30, 2014 at 11:48 AM, Kishon Vijay Abraham I <[email protected]> wrote:
> Hi,
>
> On Thursday 30 January 2014 09:49 AM, Vivek Gautam wrote:
>> Hi Kishon,
>>
>>
>> On Mon, Jan 27, 2014 at 2:27 PM, Kishon Vijay Abraham I <[email protected]> wrote:
>>> Hi,
>>
>> Thanks for review. Please find my answers inline below.
>>
>>>
>>> On Monday 20 January 2014 07:12 PM, Vivek Gautam wrote:
>>>> Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
>>>> The new driver uses the generic PHY framework and will interact
>>>> with DWC3 controller present on Exynos5 series of SoCs.
>>>> Thereby, removing old phy-samsung-usb3 driver and related code
>>>> used untill now which was based on usb/phy framework.
>>>>
>>>> Signed-off-by: Vivek Gautam <[email protected]>
>>>> ---
>>>>
>>>> Changes from v2:
>>>> 1) Added support for multiple PHYs (UTMI+ and PIPE3) and
>>>> related changes in the driver structuring.
>>>> 2) Added a xlate function to get the required phy out of
>>>> number of PHYs in mutiple PHY scenerio.
>>>> 3) Changed the names of few structures and variables to
>>>> have a clearer meaning.
>>>> 4) Added 'usb3phy_config' structure to take care of mutiple
>>>> phys for a SoC having 'exynos5_usb3phy_drv_data' driver data.
>>>> 5) Not deleting support for old driver 'phy-samsung-usb3' until
>>>> required support for generic phy is added to DWC3.
>>>>
>>>> .../devicetree/bindings/phy/samsung-phy.txt | 49 ++
>>>> drivers/phy/Kconfig | 8 +
>>>> drivers/phy/Makefile | 1 +
>>>> drivers/phy/phy-exynos5-usb3.c | 621 ++++++++++++++++++++
>>>> 4 files changed, 679 insertions(+)
>>>> create mode 100644 drivers/phy/phy-exynos5-usb3.c
>> [snip]
>>
>>>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>>>> index 330ef2d..32f9f38 100644
>>>> --- a/drivers/phy/Kconfig
>>>> +++ b/drivers/phy/Kconfig
>>>> @@ -51,4 +51,12 @@ config PHY_EXYNOS_DP_VIDEO
>>>> help
>>>> Support for Display Port PHY found on Samsung EXYNOS SoCs.
>>>>
>>>> +config PHY_EXYNOS5_USB3
>
> This shouldn't be USB3 since this driver has support for both USB2 and USB3.
> maybe just PHY_EXYNOS5_USB?
Ok, will change this.
>>>> + tristate "Exynos5 SoC series USB 3.0 PHY driver"
>>>> + depends on ARCH_EXYNOS5
>>>> + select GENERIC_PHY
>>>> + select MFD_SYSCON
>>>
>>> add depends on 'HAS_IOMEM'. Someone reported getting
>>> undefined reference to `devm_ioremap_resource' with it.
>>
>> Ok will add it.
>>
>>>> + help
>>>> + Enable USB 3.0 PHY support for Exynos 5 SoC series
>>>> +
>>>> endmenu
>> [snip]
>>
>>>> diff --git a/drivers/phy/phy-exynos5-usb3.c b/drivers/phy/phy-exynos5-usb3.c
>>>> new file mode 100644
>>>> index 0000000..24efed0
>>>> --- /dev/null
>>>> +++ b/drivers/phy/phy-exynos5-usb3.c
>>>> @@ -0,0 +1,621 @@
>>>> +/*
>>>> + * Samsung EXYNOS5 SoC series USB 3.0 PHY driver
>>>> + *
>>>> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
>>>> + * Author: Vivek Gautam <[email protected]>
>>>> + *
>>>> + * This program is free software; you can redistribute it and/or modify
>>>> + * it under the terms of the GNU General Public License version 2 as
>>>> + * published by the Free Software Foundation.
>>>> + */
>>>> +
>>>> +#include <linux/clk.h>
>>>> +#include <linux/delay.h>
>>>> +#include <linux/io.h>
>>>> +#include <linux/kernel.h>
>>>> +#include <linux/module.h>
>>>> +#include <linux/of.h>
>>>> +#include <linux/of_address.h>
>>>> +#include <linux/phy/phy.h>
>>>> +#include <linux/platform_device.h>
>>>> +#include <linux/mutex.h>
>>>> +#include <linux/mfd/syscon.h>
>>>> +#include <linux/regmap.h>
>>>> +
>>>> +/* Exynos USB PHY registers */
>>>> +#define EXYNOS5_FSEL_9MHZ6 0x0
>>>> +#define EXYNOS5_FSEL_10MHZ 0x1
>>>> +#define EXYNOS5_FSEL_12MHZ 0x2
>>>> +#define EXYNOS5_FSEL_19MHZ2 0x3
>>>> +#define EXYNOS5_FSEL_20MHZ 0x4
>>>> +#define EXYNOS5_FSEL_24MHZ 0x5
>>>> +#define EXYNOS5_FSEL_50MHZ 0x7
>>>> +
>>>> +/* EXYNOS5: USB 3.0 DRD PHY registers */
>>>> +#define EXYNOS5_DRD_LINKSYSTEM (0x04)
>>>> +
>>>> +#define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
>>>> +#define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
>>>> +#define LINKSYSTEM_XHCI_VERSION_CONTROL (0x1 << 27)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYUTMI (0x08)
>>>> +
>>>> +#define PHYUTMI_OTGDISABLE (0x1 << 6)
>>>> +#define PHYUTMI_FORCESUSPEND (0x1 << 1)
>>>> +#define PHYUTMI_FORCESLEEP (0x1 << 0)
>>>
>>> use BIT macro here and below?
>>
>> Ok.
>>
>>>> +
>>>> +#define EXYNOS5_DRD_PHYPIPE (0x0c)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYCLKRST (0x10)
>>>> +
>>>> +#define PHYCLKRST_EN_UTMISUSPEND (0x1 << 31)
>>>> +
>>>> +#define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23)
>>>> +#define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23)
>>>> +
>>>> +#define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21)
>>>> +#define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21)
>>>> +
>>>> +#define PHYCLKRST_SSC_EN (0x1 << 20)
>>>> +#define PHYCLKRST_REF_SSP_EN (0x1 << 19)
>>>> +#define PHYCLKRST_REF_CLKDIV2 (0x1 << 18)
>>>> +
>>>> +#define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11)
>>>> +#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11)
>>>> +#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x32 << 11)
>>>> +#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11)
>>>> +#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11)
>>>> +#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
>>>> +
>>>> +#define PHYCLKRST_FSEL_MASK (0x3f << 5)
>>>> +#define PHYCLKRST_FSEL(_x) ((_x) << 5)
>>>> +#define PHYCLKRST_FSEL_PAD_100MHZ (0x27 << 5)
>>>> +#define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5)
>>>> +#define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5)
>>>> +#define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5)
>>>> +
>>>> +#define PHYCLKRST_RETENABLEN (0x1 << 4)
>>>> +
>>>> +#define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2)
>>>> +#define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2)
>>>> +#define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2)
>>>> +
>>>> +#define PHYCLKRST_PORTRESET (0x1 << 1)
>>>> +#define PHYCLKRST_COMMONONN (0x1 << 0)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYREG0 (0x14)
>>>> +#define EXYNOS5_DRD_PHYREG1 (0x18)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYPARAM0 (0x1c)
>>>> +
>>>> +#define PHYPARAM0_REF_USE_PAD (0x1 << 31)
>>>> +#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26)
>>>> +#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYPARAM1 (0x20)
>>>> +
>>>> +#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
>>>> +#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYTERM (0x24)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYTEST (0x28)
>>>> +
>>>> +#define PHYTEST_POWERDOWN_SSP (0x1 << 3)
>>>> +#define PHYTEST_POWERDOWN_HSP (0x1 << 2)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYADP (0x2c)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYBATCHG (0x30)
>>>> +
>>>> +#define PHYBATCHG_UTMI_CLKSEL (0x1 << 2)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYRESUME (0x34)
>>>> +#define EXYNOS5_DRD_LINKPORT (0x44)
>>>> +
>>>> +/* Power isolation defined in power management unit */
>>>> +#define EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET (0x704)
>>>> +#define EXYNOS5_USB3DRD_PMU_ISOL (1 << 0)
>>>> +
>>>> +#define KHZ 1000
>>>> +#define MHZ (KHZ * KHZ)
>>>> +
>>>> +enum exynos5_usb3phy_id {
>>>> + EXYNOS5_USB3PHY_UTMI,
>>>> + EXYNOS5_USB3PHY_PIPE3,
>>>> + EXYNOS5_USB3PHYS_NUM,
>>>> +};
>
> here and all the structure names below shouldn't have usb3 in their names since
> this is not just a 'usb3' phy driver..
right, will change the nomenclature driver-wide (including function names too).
>>>> +
>>>> +struct usb3phy_config {
>>>> + u32 id;
>>>> + u32 reg_pmu_offset;
>>>> + void (*phy_isol)(struct phy *phy, u32 on);
>>>> +};
>>>> +
>>>> +struct exynos5_usb3phy_drv_data {
>>>> + bool has_usb30_sclk;
>>>> + bool has_multi_controller;
>>>> + const struct usb3phy_config *phy_cfg;
>>>> +};
>>>> +
>>>> +/**
>>>> + * struct exynos5_usb3phy_driver - driver data for USB 3.0 PHY
>>>
>>> Is this really a driver data? I think it should be just exynos5_usb3phy.
>> Yes, not a driver data, rather just 'exynos_usb3phy' structure. will
>> modify the name
>>
>>>> + * @dev: pointer to device instance of this platform device
>>>> + * @reg_phy: usb phy controller register memory base
>>>> + * @clk: phy clock for register access
>>>> + * @usb30_sclk: additional special clock for phy operations
>>>> + * @drv_data: pointer to SoC level driver data structure
>>>> + * @phys[]: array for 'EXYNOS5_USB3PHYS_NUM' number of PHY
>>>> + * instances each with its 'phy' and 'phy_cfg'.
>>>> + * @extrefclk: frequency select settings when using 'separate
>>>> + * reference clocks' for SS and HS operations
>>>> + * @rate: rate of reference clock to PHY block
>>>> + * @channel: number of PHY channels present in SoC
>>>> + */
>>>> +struct exynos5_usb3phy_driver {
>>>> + struct device *dev;
>>>> + void __iomem *reg_phy;
>>>> + struct clk *clk;
>>>> + struct clk *usb30_sclk;
>>>> + const struct exynos5_usb3phy_drv_data *drv_data;
>>>> + struct phy_usb_instance {
>>>> + struct phy *phy;
>>>> + u32 index;
>>>> + struct regmap *reg_isol;
>>>> + const struct usb3phy_config *phy_cfg;
>>>> + } phys[EXYNOS5_USB3PHYS_NUM];
>>>> + u32 extrefclk;
>>>> + unsigned long rate;
>>>> + u32 channel;
>>>> +};
>>>> +
>>>> +#define to_usb3phy_driver(inst) \
>>>> + container_of((inst), struct exynos5_usb3phy_driver, \
>>>> + phys[(inst)->index]);
>>>> +
>>>> +/*
>>>> + * exynos5_rate_to_clk() converts the supplied clock rate to the value that
>>>> + * can be written to the phy register.
>>>> + */
>>>> +static u32 exynos5_rate_to_clk(unsigned long rate)
>>>> +{
>>>> + unsigned int clksel;
>>>> +
>>>> + /* EXYNOS5_FSEL_MASK */
>>>> +
>>>> + switch (rate) {
>>>> + case 9600 * KHZ:
>>>> + clksel = EXYNOS5_FSEL_9MHZ6;
>>>> + break;
>>>> + case 10 * MHZ:
>>>> + clksel = EXYNOS5_FSEL_10MHZ;
>>>> + break;
>>>> + case 12 * MHZ:
>>>> + clksel = EXYNOS5_FSEL_12MHZ;
>>>> + break;
>>>> + case 19200 * KHZ:
>>>> + clksel = EXYNOS5_FSEL_19MHZ2;
>>>> + break;
>>>> + case 20 * MHZ:
>>>> + clksel = EXYNOS5_FSEL_20MHZ;
>>>> + break;
>>>> + case 24 * MHZ:
>>>> + clksel = EXYNOS5_FSEL_24MHZ;
>>>> + break;
>>>> + case 50 * MHZ:
>>>> + clksel = EXYNOS5_FSEL_50MHZ;
>>>> + break;
>>>> + default:
>>>> + clksel = -EINVAL;
>>>> + }
>>>> +
>>>> + return clksel;
>>>> +}
>>>> +
>>>> +static void exynos5_usb3phy_isol(struct phy *phy, unsigned int on)
>>>> +{
>>>> + u32 pmu_offset;
>>>> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
>>>> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
>>>> +
>>>> + pmu_offset = inst->phy_cfg->reg_pmu_offset;
>>>> + if (!inst->reg_isol)
>>>> + return;
>>>> +
>>>> + switch (drv->channel) {
>>>> + case 1:
>>>> + /* Channel 1 is at 0x708 offset */
>>>> + pmu_offset += sizeof(&pmu_offset);
>>>> + break;
>>>> + case 0:
>>>> + default:
>>>> + /* Channel 0 is at 0x704 offset */
>>>> + break;
>>>> + }
>>>
>>> This can be in a simple 'if' stmt no?
>> What if there are systems with more channels? In that case also we
>> will have to fall back to a switch-case statement ?
>
> right.
>>
>>>> +
>>>> + regmap_update_bits(inst->reg_isol, pmu_offset,
>>>> + EXYNOS5_USB3DRD_PMU_ISOL, ~on);
>>>> +}
>>>> +
>>>> +/*
>>>> + * Sets the phy clk as EXTREFCLK (XXTI) which is internal clock from clock core.
>>>> + */
>>>> +static u32 exynos5_usb3phy_set_refclk(struct exynos5_usb3phy_driver *drv)
>>>> +{
>>>> + u32 reg;
>>>> +
>>>> + reg = PHYCLKRST_REFCLKSEL_EXT_REFCLK |
>>>> + PHYCLKRST_FSEL(drv->extrefclk);
>>>> +
>>>> + switch (drv->extrefclk) {
>>>> + case EXYNOS5_FSEL_50MHZ:
>>>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
>>>> + PHYCLKRST_SSC_REFCLKSEL(0x00));
>>>> + break;
>>>> + case EXYNOS5_FSEL_24MHZ:
>>>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
>>>> + PHYCLKRST_SSC_REFCLKSEL(0x88));
>>>> + break;
>>>> + case EXYNOS5_FSEL_20MHZ:
>>>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
>>>> + PHYCLKRST_SSC_REFCLKSEL(0x00));
>>>> + break;
>>>> + case EXYNOS5_FSEL_19MHZ2:
>>>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
>>>> + PHYCLKRST_SSC_REFCLKSEL(0x88));
>>>> + break;
>>>> + default:
>>>> + dev_dbg(drv->dev, "unsupported ref clk\n");
>>>> + break;
>>>> + }
>>>> +
>>>> + return reg;
>>>> +}
>>>> +
>>>> +static int exynos5_usb3phy_init(struct phy *phy)
>>>> +{
>>>> + int ret;
>>>> + u32 phyparam0;
>>>> + u32 phyparam1;
>>>> + u32 linksystem;
>>>> + u32 phybatchg;
>>>> + u32 phytest;
>>>> + u32 phyclkrst;
>>>
>>> instead you can define a single variable 'u32 reg' for register read and writes.
>>
>> Right.
>>
>>>> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
>>>> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
>>>> +
>>>> + ret = clk_prepare_enable(drv->clk);
>>>> + if (ret)
>>>> + return ret;
>>>> +
>>>> + drv->extrefclk = exynos5_rate_to_clk(drv->rate);
>>>> + if (drv->extrefclk == -EINVAL) {
>>>> + dev_err(drv->dev, "Clock rate (%ld) not supported\n",
>>>> + drv->rate);
>>>> + return -EINVAL;
>>>> + }
>>>> +
>>>> + /* Reset USB 3.0 PHY */
>>>> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYREG0);
>>>> +
>>>> + phyparam0 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
>>>> + /* Select PHY CLK source */
>>>> + phyparam0 &= ~PHYPARAM0_REF_USE_PAD;
>>>> + /* Set Loss-of-Signal Detector sensitivity */
>>>> + phyparam0 &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
>>>> + phyparam0 |= PHYPARAM0_REF_LOSLEVEL;
>>>> + writel(phyparam0, drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
>>>> +
>>>> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYRESUME);
>>>> +
>>>> + /*
>>>> + * Setting the Frame length Adj value[6:1] to default 0x20
>>>> + * See xHCI 1.0 spec, 5.2.4
>>>> + */
>>>> + linksystem = LINKSYSTEM_XHCI_VERSION_CONTROL |
>>>> + LINKSYSTEM_FLADJ(0x20);
>>>> + writel(linksystem, drv->reg_phy + EXYNOS5_DRD_LINKSYSTEM);
>>>> +
>>>> + phyparam1 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
>>>> + /* Set Tx De-Emphasis level */
>>>> + phyparam1 &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
>>>> + phyparam1 |= PHYPARAM1_PCS_TXDEEMPH;
>>>> + writel(phyparam1, drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
>>>> +
>>>> + phybatchg = readl(drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
>>>> + phybatchg |= PHYBATCHG_UTMI_CLKSEL;
>>>> + writel(phybatchg, drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
>>>> +
>>>> + /* PHYTEST POWERDOWN Control */
>>>> + phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
>>>> + phytest &= ~(PHYTEST_POWERDOWN_SSP |
>>>> + PHYTEST_POWERDOWN_HSP);
>>>> + writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
>>>> +
>>>> + /* UTMI Power Control */
>>>> + writel(PHYUTMI_OTGDISABLE, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
>>>
>>> All these UTMI configuration should be done in usb2 init.
>> Ok, will move this to separate function.
>>
>>>> +
>>>> + phyclkrst = exynos5_usb3phy_set_refclk(drv);
>>>> +
>>>> + phyclkrst |= PHYCLKRST_PORTRESET |
>>>> + /* Digital power supply in normal operating mode */
>>>> + PHYCLKRST_RETENABLEN |
>>>> + /* Enable ref clock for SS function */
>>>> + PHYCLKRST_REF_SSP_EN |
>>>> + /* Enable spread spectrum */
>>>> + PHYCLKRST_SSC_EN |
>>>> + /* Power down HS Bias and PLL blocks in suspend mode */
>>>> + PHYCLKRST_COMMONONN;
>>>> +
>>>> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>>>> +
>>>> + udelay(10);
>>>> +
>>>> + phyclkrst &= ~PHYCLKRST_PORTRESET;
>>>> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>>>> +
>>>> + clk_disable_unprepare(drv->clk);
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int exynos5_usb3phy_exit(struct phy *phy)
>>>> +{
>>>> + int ret;
>>>> + u32 phyutmi;
>>>> + u32 phyclkrst;
>>>> + u32 phytest;
>>>
>>> same here..
>> right, will do it.
>>
>>>> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
>>>> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
>>>> +
>>>> + ret = clk_prepare_enable(drv->clk);
>>>> + if (ret)
>>>> + return ret;
>>>> +
>>>> + phyutmi = PHYUTMI_OTGDISABLE |
>>>> + PHYUTMI_FORCESUSPEND |
>>>> + PHYUTMI_FORCESLEEP;
>>>> + writel(phyutmi, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
>>>
>>> here too.. UTMI configuration should be part of USB2.
>> ok.
>>
>>>> +
>> [snip]
>>
>>>> +
>>>> +static struct phy_ops exynos5_usb3phy_ops = {
>>>> + .init = exynos5_usb3phy_init,
>>>> + .exit = exynos5_usb3phy_exit,
>>>> + .power_on = exynos5_usb3phy_power_on,
>>>> + .power_off = exynos5_usb3phy_power_off,
>>>> + .owner = THIS_MODULE,
>>>> +};
>>>> +
>>>> +const struct usb3phy_config exynos5_usb3phy_cfg[] = {
>>>> + {
>>>> + .id = EXYNOS5_USB3PHY_UTMI,
>>>
>>> This should be USB2 no?
>> Actually the thought was to have similar naming for enums.
>> EXYNOS5_USB3PHY_UTMI
>> EXYNOS5_USB3PHY_PIPE3
>>
>> Since the entire driver was going that way.
>> But will change these to a more common name
>> EXYNOS5_DRDPHY_UTMI
>> EXYNOS5_DRDPHY_PIPE3,
>> in the same fashion the register names are defined.
>> Will that be fine ?
>
> Yeah.
>
> Thanks
> Kishon
--
Best Regards
Vivek Gautam
Samsung R&D Institute, Bangalore
India
Hi Vivek,
This patch is just adding the PHY driver. I would also like to look at
some users of it, to see how this works when put together.
For now, please see my comments inline.
On 20.01.2014 14:42, Vivek Gautam wrote:
> Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
> The new driver uses the generic PHY framework and will interact
> with DWC3 controller present on Exynos5 series of SoCs.
> Thereby, removing old phy-samsung-usb3 driver and related code
> used untill now which was based on usb/phy framework.
>
> Signed-off-by: Vivek Gautam <[email protected]>
> ---
>
> Changes from v2:
> 1) Added support for multiple PHYs (UTMI+ and PIPE3) and
> related changes in the driver structuring.
I'm a bit skeptical about this separation. Can the PHY operate with just
the UTMI+ or PIPE3 part enabled alone without the other? Can any PHY
consumer operate this way?
Introducing separation of something that can't exist alone doesn't add
any value, but instead makes things more difficult to work with. Of
course, it's fine if the answer to my questions above if yes, but better
safe than sorry.
> 2) Added a xlate function to get the required phy out of
> number of PHYs in mutiple PHY scenerio.
> 3) Changed the names of few structures and variables to
> have a clearer meaning.
> 4) Added 'usb3phy_config' structure to take care of mutiple
> phys for a SoC having 'exynos5_usb3phy_drv_data' driver data.
> 5) Not deleting support for old driver 'phy-samsung-usb3' until
> required support for generic phy is added to DWC3.
[snip]
> +
> +- aliases: For SoCs like Exynos5420 having multiple USB PHY controllers,
> + 'usb3_phy' nodes should have numbered alias in the aliases node,
> + in the form of usb3phyN, N = 0, 1... (depending on number of
> + controllers).
> +Example:
> + aliases {
> + usb3phy0 = &usb3_phy0;
> + usb3phy1 = &usb3_phy1;
> + };
What is the reason to have these aliases?
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 330ef2d..32f9f38 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -51,4 +51,12 @@ config PHY_EXYNOS_DP_VIDEO
> help
> Support for Display Port PHY found on Samsung EXYNOS SoCs.
>
> +config PHY_EXYNOS5_USB3
> + tristate "Exynos5 SoC series USB 3.0 PHY driver"
> + depends on ARCH_EXYNOS5
> + select GENERIC_PHY
> + select MFD_SYSCON
> + help
> + Enable USB 3.0 PHY support for Exynos 5 SoC series
> +
> endmenu
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index d0caae9..9c06a61 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -7,3 +7,4 @@ obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) += phy-exynos-dp-video.o
> obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
> obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
> obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
> +obj-$(CONFIG_PHY_EXYNOS5_USB3) += phy-exynos5-usb3.o
> diff --git a/drivers/phy/phy-exynos5-usb3.c b/drivers/phy/phy-exynos5-usb3.c
> new file mode 100644
> index 0000000..24efed0
> --- /dev/null
> +++ b/drivers/phy/phy-exynos5-usb3.c
> @@ -0,0 +1,621 @@
> +/*
> + * Samsung EXYNOS5 SoC series USB 3.0 PHY driver
> + *
> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> + * Author: Vivek Gautam <[email protected]>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/mutex.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/regmap.h>
> +
> +/* Exynos USB PHY registers */
> +#define EXYNOS5_FSEL_9MHZ6 0x0
> +#define EXYNOS5_FSEL_10MHZ 0x1
> +#define EXYNOS5_FSEL_12MHZ 0x2
> +#define EXYNOS5_FSEL_19MHZ2 0x3
> +#define EXYNOS5_FSEL_20MHZ 0x4
> +#define EXYNOS5_FSEL_24MHZ 0x5
> +#define EXYNOS5_FSEL_50MHZ 0x7
> +
> +/* EXYNOS5: USB 3.0 DRD PHY registers */
> +#define EXYNOS5_DRD_LINKSYSTEM (0x04)
nit: No need for parentheses around simple literal. (+ more occurrences
below)
> +
> +#define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
> +#define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
> +#define LINKSYSTEM_XHCI_VERSION_CONTROL (0x1 << 27)
nit: BIT() macro could be used for single bits. (+ more occurrences below)
> +
> +#define EXYNOS5_DRD_PHYUTMI (0x08)
> +
> +#define PHYUTMI_OTGDISABLE (0x1 << 6)
> +#define PHYUTMI_FORCESUSPEND (0x1 << 1)
> +#define PHYUTMI_FORCESLEEP (0x1 << 0)
> +
> +#define EXYNOS5_DRD_PHYPIPE (0x0c)
> +
> +#define EXYNOS5_DRD_PHYCLKRST (0x10)
> +
> +#define PHYCLKRST_EN_UTMISUSPEND (0x1 << 31)
> +
> +#define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23)
> +#define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23)
> +
> +#define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21)
> +#define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21)
> +
> +#define PHYCLKRST_SSC_EN (0x1 << 20)
> +#define PHYCLKRST_REF_SSP_EN (0x1 << 19)
> +#define PHYCLKRST_REF_CLKDIV2 (0x1 << 18)
> +
> +#define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x32 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
> +
> +#define PHYCLKRST_FSEL_MASK (0x3f << 5)
> +#define PHYCLKRST_FSEL(_x) ((_x) << 5)
> +#define PHYCLKRST_FSEL_PAD_100MHZ (0x27 << 5)
> +#define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5)
> +#define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5)
> +#define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5)
> +
> +#define PHYCLKRST_RETENABLEN (0x1 << 4)
> +
> +#define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2)
> +#define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2)
> +#define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2)
> +
> +#define PHYCLKRST_PORTRESET (0x1 << 1)
> +#define PHYCLKRST_COMMONONN (0x1 << 0)
> +
> +#define EXYNOS5_DRD_PHYREG0 (0x14)
> +#define EXYNOS5_DRD_PHYREG1 (0x18)
> +
> +#define EXYNOS5_DRD_PHYPARAM0 (0x1c)
> +
> +#define PHYPARAM0_REF_USE_PAD (0x1 << 31)
> +#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26)
> +#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26)
> +
> +#define EXYNOS5_DRD_PHYPARAM1 (0x20)
> +
> +#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
> +#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
> +
> +#define EXYNOS5_DRD_PHYTERM (0x24)
> +
> +#define EXYNOS5_DRD_PHYTEST (0x28)
> +
> +#define PHYTEST_POWERDOWN_SSP (0x1 << 3)
> +#define PHYTEST_POWERDOWN_HSP (0x1 << 2)
> +
> +#define EXYNOS5_DRD_PHYADP (0x2c)
> +
> +#define EXYNOS5_DRD_PHYBATCHG (0x30)
> +
> +#define PHYBATCHG_UTMI_CLKSEL (0x1 << 2)
> +
> +#define EXYNOS5_DRD_PHYRESUME (0x34)
> +#define EXYNOS5_DRD_LINKPORT (0x44)
> +
> +/* Power isolation defined in power management unit */
> +#define EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET (0x704)
> +#define EXYNOS5_USB3DRD_PMU_ISOL (1 << 0)
> +
> +#define KHZ 1000
> +#define MHZ (KHZ * KHZ)
> +
> +enum exynos5_usb3phy_id {
> + EXYNOS5_USB3PHY_UTMI,
> + EXYNOS5_USB3PHY_PIPE3,
> + EXYNOS5_USB3PHYS_NUM,
> +};
> +
> +struct usb3phy_config {
> + u32 id;
> + u32 reg_pmu_offset;
> + void (*phy_isol)(struct phy *phy, u32 on);
> +};
> +
> +struct exynos5_usb3phy_drv_data {
> + bool has_usb30_sclk;
> + bool has_multi_controller;
> + const struct usb3phy_config *phy_cfg;
> +};
> +
> +/**
> + * struct exynos5_usb3phy_driver - driver data for USB 3.0 PHY
> + * @dev: pointer to device instance of this platform device
> + * @reg_phy: usb phy controller register memory base
> + * @clk: phy clock for register access
> + * @usb30_sclk: additional special clock for phy operations
> + * @drv_data: pointer to SoC level driver data structure
> + * @phys[]: array for 'EXYNOS5_USB3PHYS_NUM' number of PHY
> + * instances each with its 'phy' and 'phy_cfg'.
> + * @extrefclk: frequency select settings when using 'separate
> + * reference clocks' for SS and HS operations
> + * @rate: rate of reference clock to PHY block
> + * @channel: number of PHY channels present in SoC
> + */
> +struct exynos5_usb3phy_driver {
> + struct device *dev;
> + void __iomem *reg_phy;
> + struct clk *clk;
> + struct clk *usb30_sclk;
> + const struct exynos5_usb3phy_drv_data *drv_data;
> + struct phy_usb_instance {
> + struct phy *phy;
> + u32 index;
> + struct regmap *reg_isol;
> + const struct usb3phy_config *phy_cfg;
> + } phys[EXYNOS5_USB3PHYS_NUM];
> + u32 extrefclk;
> + unsigned long rate;
> + u32 channel;
> +};
> +
> +#define to_usb3phy_driver(inst) \
> + container_of((inst), struct exynos5_usb3phy_driver, \
> + phys[(inst)->index]);
> +
> +/*
> + * exynos5_rate_to_clk() converts the supplied clock rate to the value that
> + * can be written to the phy register.
> + */
> +static u32 exynos5_rate_to_clk(unsigned long rate)
> +{
> + unsigned int clksel;
> +
> + /* EXYNOS5_FSEL_MASK */
> +
> + switch (rate) {
> + case 9600 * KHZ:
> + clksel = EXYNOS5_FSEL_9MHZ6;
> + break;
> + case 10 * MHZ:
> + clksel = EXYNOS5_FSEL_10MHZ;
> + break;
> + case 12 * MHZ:
> + clksel = EXYNOS5_FSEL_12MHZ;
> + break;
> + case 19200 * KHZ:
> + clksel = EXYNOS5_FSEL_19MHZ2;
> + break;
> + case 20 * MHZ:
> + clksel = EXYNOS5_FSEL_20MHZ;
> + break;
> + case 24 * MHZ:
> + clksel = EXYNOS5_FSEL_24MHZ;
> + break;
> + case 50 * MHZ:
> + clksel = EXYNOS5_FSEL_50MHZ;
> + break;
> + default:
> + clksel = -EINVAL;
> + }
> +
> + return clksel;
> +}
> +
> +static void exynos5_usb3phy_isol(struct phy *phy, unsigned int on)
> +{
> + u32 pmu_offset;
> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
> +
> + pmu_offset = inst->phy_cfg->reg_pmu_offset;
> + if (!inst->reg_isol)
> + return;
> +
> + switch (drv->channel) {
> + case 1:
> + /* Channel 1 is at 0x708 offset */
> + pmu_offset += sizeof(&pmu_offset);
> + break;
> + case 0:
> + default:
> + /* Channel 0 is at 0x704 offset */
> + break;
> + }
> +
> + regmap_update_bits(inst->reg_isol, pmu_offset,
> + EXYNOS5_USB3DRD_PMU_ISOL, ~on);
> +}
> +
> +/*
> + * Sets the phy clk as EXTREFCLK (XXTI) which is internal clock from clock core.
> + */
> +static u32 exynos5_usb3phy_set_refclk(struct exynos5_usb3phy_driver *drv)
> +{
> + u32 reg;
> +
> + reg = PHYCLKRST_REFCLKSEL_EXT_REFCLK |
> + PHYCLKRST_FSEL(drv->extrefclk);
> +
> + switch (drv->extrefclk) {
> + case EXYNOS5_FSEL_50MHZ:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x00));
> + break;
> + case EXYNOS5_FSEL_24MHZ:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x88));
> + break;
> + case EXYNOS5_FSEL_20MHZ:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x00));
> + break;
> + case EXYNOS5_FSEL_19MHZ2:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x88));
> + break;
> + default:
> + dev_dbg(drv->dev, "unsupported ref clk\n");
> + break;
> + }
> +
> + return reg;
> +}
> +
> +static int exynos5_usb3phy_init(struct phy *phy)
> +{
> + int ret;
> + u32 phyparam0;
> + u32 phyparam1;
> + u32 linksystem;
> + u32 phybatchg;
> + u32 phytest;
> + u32 phyclkrst;
> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
> +
> + ret = clk_prepare_enable(drv->clk);
> + if (ret)
> + return ret;
> +
> + drv->extrefclk = exynos5_rate_to_clk(drv->rate);
> + if (drv->extrefclk == -EINVAL) {
> + dev_err(drv->dev, "Clock rate (%ld) not supported\n",
> + drv->rate);
> + return -EINVAL;
> + }
> +
> + /* Reset USB 3.0 PHY */
> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYREG0);
> +
> + phyparam0 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
> + /* Select PHY CLK source */
> + phyparam0 &= ~PHYPARAM0_REF_USE_PAD;
> + /* Set Loss-of-Signal Detector sensitivity */
> + phyparam0 &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
> + phyparam0 |= PHYPARAM0_REF_LOSLEVEL;
> + writel(phyparam0, drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
> +
> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYRESUME);
> +
> + /*
> + * Setting the Frame length Adj value[6:1] to default 0x20
> + * See xHCI 1.0 spec, 5.2.4
> + */
> + linksystem = LINKSYSTEM_XHCI_VERSION_CONTROL |
> + LINKSYSTEM_FLADJ(0x20);
> + writel(linksystem, drv->reg_phy + EXYNOS5_DRD_LINKSYSTEM);
> +
> + phyparam1 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
> + /* Set Tx De-Emphasis level */
> + phyparam1 &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
> + phyparam1 |= PHYPARAM1_PCS_TXDEEMPH;
> + writel(phyparam1, drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
> +
> + phybatchg = readl(drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
> + phybatchg |= PHYBATCHG_UTMI_CLKSEL;
> + writel(phybatchg, drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
> +
> + /* PHYTEST POWERDOWN Control */
> + phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> + phytest &= ~(PHYTEST_POWERDOWN_SSP |
> + PHYTEST_POWERDOWN_HSP);
> + writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> +
> + /* UTMI Power Control */
> + writel(PHYUTMI_OTGDISABLE, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
> +
> + phyclkrst = exynos5_usb3phy_set_refclk(drv);
> +
> + phyclkrst |= PHYCLKRST_PORTRESET |
> + /* Digital power supply in normal operating mode */
> + PHYCLKRST_RETENABLEN |
> + /* Enable ref clock for SS function */
> + PHYCLKRST_REF_SSP_EN |
> + /* Enable spread spectrum */
> + PHYCLKRST_SSC_EN |
> + /* Power down HS Bias and PLL blocks in suspend mode */
> + PHYCLKRST_COMMONONN;
> +
> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +
> + udelay(10);
> +
> + phyclkrst &= ~PHYCLKRST_PORTRESET;
> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +
> + clk_disable_unprepare(drv->clk);
I'm still not convinced that this is the right place for this setup.
This way you force consumer driver to always call phy_power_on() and
phy_init() together, otherwise the PHY won't work.
I believe the right thing to do here is to do all the initialization in
.power_on() and let the driver simply call phy_power_on() when it needs
the PHY and phy_power_off() otherwise.
Analogically, .exit() should be merged into .power_off().
> +
> + return 0;
> +}
[snip]
> + /*
> + * Exynos5420 SoC has multiple channels for USB 3.0 PHY, with
> + * each having separate power control registers.
> + * 'drv->channel' facilitates to set such registers.
> + */
> + if (drv->drv_data->has_multi_controller) {
> + drv->channel = of_alias_get_id(node, "usb3phy");
> + if (drv->channel < 0) {
> + dev_err(dev, "Invalid usb3drd phy node\n");
> + return -EINVAL;
> + }
> + }
Aha, so this is why you need aliases. Maybe a "samsung,pmu-offset"
property, simply specifying the offset to PMU regs would be better here?
> +
> + drv->clk = devm_clk_get(dev, "phy");
> + if (IS_ERR(drv->clk)) {
> + dev_err(dev, "Failed to get clock of phy controller\n");
> + return PTR_ERR(drv->clk);
> + }
> +
> + /*
> + * Exysno5420 SoC has an additional special clock, used for
> + * for USB 3.0 PHY operation, this clock goes to the PHY block
> + * as a reference clock to clock generation block of the controller,
> + * named as 'USB30_SCLK_100M'.
> + */
> + if (drv_data->has_usb30_sclk) {
> + drv->usb30_sclk = devm_clk_get(dev, "usb30_sclk_100m");
> + if (IS_ERR(drv->usb30_sclk)) {
> + dev_err(dev, "Failed to get phy reference clock\n");
> + return PTR_ERR(drv->usb30_sclk);
> + }
> + }
> +
> + clk = clk_get(dev, "usb3phy_refclk");
> + if (IS_ERR(clk)) {
> + dev_err(dev, "Failed to get reference clock of usb3drd phy\n");
> + return PTR_ERR(clk);
> + }
> + drv->rate = clk_get_rate(clk);
> + clk_put(clk);
To comply with clock API semantics, you should keep the reference on
this clock until the driver is removed. Moreover, I believe you should
call clk_prepare_enable() on it as well, to make sure that the clock is
enabled, even if current implementation of clock drivers for Exynos 5
can't disable this clock.
Best regards,
Tomasz
Hi,
On Thursday 06 February 2014 07:37 PM, Tomasz Figa wrote:
> Hi Vivek,
>
> This patch is just adding the PHY driver. I would also like to look at some
> users of it, to see how this works when put together.
>
> For now, please see my comments inline.
>
> On 20.01.2014 14:42, Vivek Gautam wrote:
>> Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
>> The new driver uses the generic PHY framework and will interact
>> with DWC3 controller present on Exynos5 series of SoCs.
>> Thereby, removing old phy-samsung-usb3 driver and related code
>> used untill now which was based on usb/phy framework.
>>
>> Signed-off-by: Vivek Gautam <[email protected]>
>> ---
>>
>> Changes from v2:
>> 1) Added support for multiple PHYs (UTMI+ and PIPE3) and
>> related changes in the driver structuring.
>
> I'm a bit skeptical about this separation. Can the PHY operate with just the
> UTMI+ or PIPE3 part enabled alone without the other? Can any PHY consumer
> operate this way?
Theoretically yes. If the USB controller should operate only in high-speed
mode, the PIPE3 part is not required at all. However for super speed mode both
PIPE3 part and UTMI part should be enabled. Maybe it doesn't work that way with
all SoCs because of some HW bug.
>
> Introducing separation of something that can't exist alone doesn't add any
> value, but instead makes things more difficult to work with. Of course, it's
IMO separating it into different parts adds more clarity to the driver.
Thanks
Kishon
Hi Tomasz,
On Thu, Feb 6, 2014 at 7:37 PM, Tomasz Figa <[email protected]> wrote:
> Hi Vivek,
>
> This patch is just adding the PHY driver. I would also like to look at some
> users of it, to see how this works when put together.
The DWC3's changes had been posted by Kishon sometime back, which will enable
DWC3 to use generic PHY dirver. [1]
I had skipped posting corresponding arch patch to use DWC3 on Exynos5
(although i had
posted that in earlier versions of the patch-series).
I will post the corresponding arch patches in the next version of the
patch-series.
>
> For now, please see my comments inline.
>
>
> On 20.01.2014 14:42, Vivek Gautam wrote:
>>
>> Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
>> The new driver uses the generic PHY framework and will interact
>> with DWC3 controller present on Exynos5 series of SoCs.
>> Thereby, removing old phy-samsung-usb3 driver and related code
>> used untill now which was based on usb/phy framework.
>>
>> Signed-off-by: Vivek Gautam <[email protected]>
>> ---
>>
>> Changes from v2:
>> 1) Added support for multiple PHYs (UTMI+ and PIPE3) and
>> related changes in the driver structuring.
>
>
> I'm a bit skeptical about this separation. Can the PHY operate with just the
> UTMI+ or PIPE3 part enabled alone without the other? Can any PHY consumer
> operate this way?
Yes :-)
As also pointed by Kishon the PHY consumer (which is DWC3 in case of
Exynos5 SoC series)
should theoretically be able use either UTMI+ phy for High speed
operations or both (UTMI+ and PIPE3)
for Super Speed operations.
>
> Introducing separation of something that can't exist alone doesn't add any
> value, but instead makes things more difficult to work with. Of course, it's
> fine if the answer to my questions above if yes, but better safe than sorry.
>
>
>> 2) Added a xlate function to get the required phy out of
>> number of PHYs in mutiple PHY scenerio.
>> 3) Changed the names of few structures and variables to
>> have a clearer meaning.
>> 4) Added 'usb3phy_config' structure to take care of mutiple
>> phys for a SoC having 'exynos5_usb3phy_drv_data' driver data.
>> 5) Not deleting support for old driver 'phy-samsung-usb3' until
>> required support for generic phy is added to DWC3.
>
>
> [snip]
>
>
>> +
>> +- aliases: For SoCs like Exynos5420 having multiple USB PHY controllers,
>> + 'usb3_phy' nodes should have numbered alias in the aliases
>> node,
>> + in the form of usb3phyN, N = 0, 1... (depending on number of
>> + controllers).
>> +Example:
>> + aliases {
>> + usb3phy0 = &usb3_phy0;
>> + usb3phy1 = &usb3_phy1;
>> + };
>
>
> What is the reason to have these aliases?
>
>
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index 330ef2d..32f9f38 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -51,4 +51,12 @@ config PHY_EXYNOS_DP_VIDEO
>> help
>> Support for Display Port PHY found on Samsung EXYNOS SoCs.
>>
>> +config PHY_EXYNOS5_USB3
>> + tristate "Exynos5 SoC series USB 3.0 PHY driver"
>> + depends on ARCH_EXYNOS5
>> + select GENERIC_PHY
>> + select MFD_SYSCON
>> + help
>> + Enable USB 3.0 PHY support for Exynos 5 SoC series
>> +
>> endmenu
>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>> index d0caae9..9c06a61 100644
>> --- a/drivers/phy/Makefile
>> +++ b/drivers/phy/Makefile
>> @@ -7,3 +7,4 @@ obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) +=
>> phy-exynos-dp-video.o
>> obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
>> obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
>> obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
>> +obj-$(CONFIG_PHY_EXYNOS5_USB3) += phy-exynos5-usb3.o
>> diff --git a/drivers/phy/phy-exynos5-usb3.c
>> b/drivers/phy/phy-exynos5-usb3.c
>> new file mode 100644
>> index 0000000..24efed0
>> --- /dev/null
>> +++ b/drivers/phy/phy-exynos5-usb3.c
>> @@ -0,0 +1,621 @@
>> +/*
>> + * Samsung EXYNOS5 SoC series USB 3.0 PHY driver
>> + *
>> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
>> + * Author: Vivek Gautam <[email protected]>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + */
>> +
>> +#include <linux/clk.h>
>> +#include <linux/delay.h>
>> +#include <linux/io.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/of_address.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/mutex.h>
>> +#include <linux/mfd/syscon.h>
>> +#include <linux/regmap.h>
>> +
>> +/* Exynos USB PHY registers */
>> +#define EXYNOS5_FSEL_9MHZ6 0x0
>> +#define EXYNOS5_FSEL_10MHZ 0x1
>> +#define EXYNOS5_FSEL_12MHZ 0x2
>> +#define EXYNOS5_FSEL_19MHZ2 0x3
>> +#define EXYNOS5_FSEL_20MHZ 0x4
>> +#define EXYNOS5_FSEL_24MHZ 0x5
>> +#define EXYNOS5_FSEL_50MHZ 0x7
>> +
>> +/* EXYNOS5: USB 3.0 DRD PHY registers */
>> +#define EXYNOS5_DRD_LINKSYSTEM (0x04)
>
>
> nit: No need for parentheses around simple literal. (+ more occurrences
> below)
Ok, will remove them.
>
>
>> +
>> +#define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
>> +#define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
>> +#define LINKSYSTEM_XHCI_VERSION_CONTROL (0x1 << 27)
>
>
> nit: BIT() macro could be used for single bits. (+ more occurrences below)
Pointed out by Kishon too. :-)
Will use them.
>
>
>> +
>> +#define EXYNOS5_DRD_PHYUTMI (0x08)
[snip]
>> +
>> +static int exynos5_usb3phy_init(struct phy *phy)
>> +{
>> + int ret;
>> + u32 phyparam0;
>> + u32 phyparam1;
>> + u32 linksystem;
>> + u32 phybatchg;
>> + u32 phytest;
>> + u32 phyclkrst;
>> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
>> + struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
>> +
>> + ret = clk_prepare_enable(drv->clk);
>> + if (ret)
>> + return ret;
>> +
>> + drv->extrefclk = exynos5_rate_to_clk(drv->rate);
>> + if (drv->extrefclk == -EINVAL) {
>> + dev_err(drv->dev, "Clock rate (%ld) not supported\n",
>> + drv->rate);
>> + return -EINVAL;
>> + }
>> +
>> + /* Reset USB 3.0 PHY */
>> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYREG0);
>> +
>> + phyparam0 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
>> + /* Select PHY CLK source */
>> + phyparam0 &= ~PHYPARAM0_REF_USE_PAD;
>> + /* Set Loss-of-Signal Detector sensitivity */
>> + phyparam0 &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
>> + phyparam0 |= PHYPARAM0_REF_LOSLEVEL;
>> + writel(phyparam0, drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
>> +
>> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYRESUME);
>> +
>> + /*
>> + * Setting the Frame length Adj value[6:1] to default 0x20
>> + * See xHCI 1.0 spec, 5.2.4
>> + */
>> + linksystem = LINKSYSTEM_XHCI_VERSION_CONTROL |
>> + LINKSYSTEM_FLADJ(0x20);
>> + writel(linksystem, drv->reg_phy + EXYNOS5_DRD_LINKSYSTEM);
>> +
>> + phyparam1 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
>> + /* Set Tx De-Emphasis level */
>> + phyparam1 &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
>> + phyparam1 |= PHYPARAM1_PCS_TXDEEMPH;
>> + writel(phyparam1, drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
>> +
>> + phybatchg = readl(drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
>> + phybatchg |= PHYBATCHG_UTMI_CLKSEL;
>> + writel(phybatchg, drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
>> +
>> + /* PHYTEST POWERDOWN Control */
>> + phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
>> + phytest &= ~(PHYTEST_POWERDOWN_SSP |
>> + PHYTEST_POWERDOWN_HSP);
>> + writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
>> +
>> + /* UTMI Power Control */
>> + writel(PHYUTMI_OTGDISABLE, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
>> +
>> + phyclkrst = exynos5_usb3phy_set_refclk(drv);
>> +
>> + phyclkrst |= PHYCLKRST_PORTRESET |
>> + /* Digital power supply in normal operating mode */
>> + PHYCLKRST_RETENABLEN |
>> + /* Enable ref clock for SS function */
>> + PHYCLKRST_REF_SSP_EN |
>> + /* Enable spread spectrum */
>> + PHYCLKRST_SSC_EN |
>> + /* Power down HS Bias and PLL blocks in suspend mode
>> */
>> + PHYCLKRST_COMMONONN;
>> +
>> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>> +
>> + udelay(10);
>> +
>> + phyclkrst &= ~PHYCLKRST_PORTRESET;
>> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>> +
>> + clk_disable_unprepare(drv->clk);
>
>
> I'm still not convinced that this is the right place for this setup. This
> way you force consumer driver to always call phy_power_on() and phy_init()
> together, otherwise the PHY won't work.
Isn't how the things are supposed to work ?
call phy_init() to initialize the PHY and then call phy_power_on().
power_on() will simply
take care of disabling the power isolation for PHY (or simply provide
enable power to PHY)
and therefore doesn't need to worry about the initialization part.
Atleast that's the approach in DWC3 patch from Kishon [1]
>
> I believe the right thing to do here is to do all the initialization in
> .power_on() and let the driver simply call phy_power_on() when it needs the
> PHY and phy_power_off() otherwise.
If this is what we should be doing then what will be the purpose of
two separate APIs :
phy_power_on() and phy_init().
Am i missing while understanding the things.
>
> Analogically, .exit() should be merged into .power_off().
>
>
>> +
>> + return 0;
>> +}
>
>
> [snip]
>
>
>> + /*
>> + * Exynos5420 SoC has multiple channels for USB 3.0 PHY, with
>> + * each having separate power control registers.
>> + * 'drv->channel' facilitates to set such registers.
>> + */
>> + if (drv->drv_data->has_multi_controller) {
>> + drv->channel = of_alias_get_id(node, "usb3phy");
>> + if (drv->channel < 0) {
>> + dev_err(dev, "Invalid usb3drd phy node\n");
>> + return -EINVAL;
>> + }
>> + }
>
>
> Aha, so this is why you need aliases. Maybe a "samsung,pmu-offset" property,
> simply specifying the offset to PMU regs would be better here?
Ok.
>
>
>> +
>> + drv->clk = devm_clk_get(dev, "phy");
>> + if (IS_ERR(drv->clk)) {
>> + dev_err(dev, "Failed to get clock of phy controller\n");
>> + return PTR_ERR(drv->clk);
>> + }
>> +
>> + /*
>> + * Exysno5420 SoC has an additional special clock, used for
>> + * for USB 3.0 PHY operation, this clock goes to the PHY block
>> + * as a reference clock to clock generation block of the
>> controller,
>> + * named as 'USB30_SCLK_100M'.
>> + */
>> + if (drv_data->has_usb30_sclk) {
>> + drv->usb30_sclk = devm_clk_get(dev, "usb30_sclk_100m");
>> + if (IS_ERR(drv->usb30_sclk)) {
>> + dev_err(dev, "Failed to get phy reference
>> clock\n");
>> + return PTR_ERR(drv->usb30_sclk);
>> + }
>> + }
>> +
>> + clk = clk_get(dev, "usb3phy_refclk");
>> + if (IS_ERR(clk)) {
>> + dev_err(dev, "Failed to get reference clock of usb3drd
>> phy\n");
>> + return PTR_ERR(clk);
>> + }
>> + drv->rate = clk_get_rate(clk);
>> + clk_put(clk);
>
>
> To comply with clock API semantics, you should keep the reference on this
> clock until the driver is removed. Moreover, I believe you should call
> clk_prepare_enable() on it as well, to make sure that the clock is enabled,
> even if current implementation of clock drivers for Exynos 5 can't disable
> this clock.
Ok will do this.
--
Best Regards
Vivek Gautam
Samsung R&D Institute, Bangalore
India
Hi Vivek,
On 14.02.2014 14:53, Vivek Gautam wrote:
>>> Changes from v2:
>>> 1) Added support for multiple PHYs (UTMI+ and PIPE3) and
>>> related changes in the driver structuring.
>>
>>
>> I'm a bit skeptical about this separation. Can the PHY operate with just the
>> UTMI+ or PIPE3 part enabled alone without the other? Can any PHY consumer
>> operate this way?
>
> Yes :-)
> As also pointed by Kishon the PHY consumer (which is DWC3 in case of
> Exynos5 SoC series)
> should theoretically be able use either UTMI+ phy for High speed
> operations or both (UTMI+ and PIPE3)
> for Super Speed operations.
OK, that's fine then. This is the explanation I needed, thanks.
>>
>> I believe the right thing to do here is to do all the initialization in
>> .power_on() and let the driver simply call phy_power_on() when it needs the
>> PHY and phy_power_off() otherwise.
>
> If this is what we should be doing then what will be the purpose of
> two separate APIs :
> phy_power_on() and phy_init().
> Am i missing while understanding the things.
>
I don't understand this separation as well. Operations that should be
done together shouldn't be separated. Is there any case when you can
call one of phy_power_on() and phy_init() without calling another one
right before/after it?
Best regards,
Tomasz
Hi Tomasz,
On Fri, Feb 14, 2014 at 9:17 PM, Tomasz Figa <[email protected]> wrote:
mistakenly didn't do "Reply All", so sending it again.
> Hi Vivek,
>
>
> On 14.02.2014 14:53, Vivek Gautam wrote:
>>>>
>>>> Changes from v2:
>>>> 1) Added support for multiple PHYs (UTMI+ and PIPE3) and
>>>> related changes in the driver structuring.
>>>
>>>
>>>
>>> I'm a bit skeptical about this separation. Can the PHY operate with just
>>> the
>>> UTMI+ or PIPE3 part enabled alone without the other? Can any PHY consumer
>>> operate this way?
>>
>>
>> Yes :-)
>> As also pointed by Kishon the PHY consumer (which is DWC3 in case of
>> Exynos5 SoC series)
>> should theoretically be able use either UTMI+ phy for High speed
>> operations or both (UTMI+ and PIPE3)
>> for Super Speed operations.
>
>
> OK, that's fine then. This is the explanation I needed, thanks.
>
>
>>>
>>> I believe the right thing to do here is to do all the initialization in
>>> .power_on() and let the driver simply call phy_power_on() when it needs
>>> the
>>> PHY and phy_power_off() otherwise.
>>
>>
>> If this is what we should be doing then what will be the purpose of
>> two separate APIs :
>> phy_power_on() and phy_init().
>> Am i missing while understanding the things.
>>
>
> I don't understand this separation as well. Operations that should be done
> together shouldn't be separated. Is there any case when you can call one of
> phy_power_on() and phy_init() without calling another one right before/after
> it?
Most of the PHY consumers need to call phy_power_on() as well as phy_init()
to get PHY working (if the PHY provider gives callback to both).
I think the idea would have been to separate out the initialization
related and power related
jobs (which may include setting up the PMUs and may be regulators ?)
But, i think it's true, if the PHY provider callback for both
phy_power_on() and phy_init()
then the consumer __has__ to call both to get things working.
--
Best Regards
Vivek Gautam
Samsung R&D Institute, Bangalore
India