2014-11-19 15:51:15

by Nicolas Ferre

[permalink] [raw]
Subject: Re: [PATCH 6/6] ARM: at91/dt: add ISI node

On 30/09/2014 18:19, Boris Brezillon :
> Add ISI (Image Sensor Interface) DT node.
>
> Signed-off-by: Boris Brezillon <[email protected]>

I take this one for at91-3.19-dt2

Thanks, best regards.

> ---
> arch/arm/boot/dts/at91sam9g45.dtsi | 32 ++++++++++++++++++++++++++++++++
> 1 file changed, 32 insertions(+)
>
> diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
> index 790c890..5d8746a 100644
> --- a/arch/arm/boot/dts/at91sam9g45.dtsi
> +++ b/arch/arm/boot/dts/at91sam9g45.dtsi
> @@ -804,6 +804,27 @@
> };
> };
>
> + isi {
> + pinctrl_isi: isi-0 {
> + atmel,pins = <AT91_PIOB 8 AT91_PERIPH_B AT91_PINCTRL_NONE /* D8 */
> + AT91_PIOB 9 AT91_PERIPH_B AT91_PINCTRL_NONE /* D9 */
> + AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE /* D10 */
> + AT91_PIOB 11 AT91_PERIPH_B AT91_PINCTRL_NONE /* D11 */
> + AT91_PIOB 20 AT91_PERIPH_A AT91_PINCTRL_NONE /* D0 */
> + AT91_PIOB 21 AT91_PERIPH_A AT91_PINCTRL_NONE /* D1 */
> + AT91_PIOB 22 AT91_PERIPH_A AT91_PINCTRL_NONE /* D2 */
> + AT91_PIOB 23 AT91_PERIPH_A AT91_PINCTRL_NONE /* D3 */
> + AT91_PIOB 24 AT91_PERIPH_A AT91_PINCTRL_NONE /* D4 */
> + AT91_PIOB 25 AT91_PERIPH_A AT91_PINCTRL_NONE /* D5 */
> + AT91_PIOB 26 AT91_PERIPH_A AT91_PINCTRL_NONE /* D6 */
> + AT91_PIOB 27 AT91_PERIPH_A AT91_PINCTRL_NONE /* D7 */
> + AT91_PIOB 28 AT91_PERIPH_A AT91_PINCTRL_NONE /* PCK */
> + AT91_PIOB 29 AT91_PERIPH_A AT91_PINCTRL_NONE /* VSYNC */
> + AT91_PIOB 30 AT91_PERIPH_A AT91_PINCTRL_NONE /* HSYNC */
> + AT91_PIOB 31 AT91_PERIPH_A AT91_PINCTRL_NONE /* MCK */>;
> + };
> + };
> +
> pioA: gpio@fffff200 {
> compatible = "atmel,at91rm9200-gpio";
> reg = <0xfffff200 0x200>;
> @@ -1029,6 +1050,17 @@
> };
> };
>
> + isi@fffb4000 {
> + compatible = "atmel,at91sam9g45-isi";
> + reg = <0xfffb4000 0x4000>;
> + interrupts = <26 IRQ_TYPE_LEVEL_HIGH 5>;
> + clocks = <&isi_clk>;
> + clock-names = "isi_clk";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_isi>;
> + status = "disabled";
> + };
> +
> pwm0: pwm@fffb8000 {
> compatible = "atmel,at91sam9rl-pwm";
> reg = <0xfffb8000 0x300>;
>


--
Nicolas Ferre