Dear all,
very often we observe issue with Ethernet cable detection during cable
unplugging and plugging.
We use Voipac i.MX51 SOMs (System On Modules). They are based on
Freescale i.MX51 CPU with LAN7800 PHY in MII mode. The schematic of PHY
connection is very similar to the Freescale i.MX51 Babbage board.
The Ethernet interface eth0 is configured statically for simplicity, but
same issue exists with DHCP configuration.
I did a lot of tests to determine stability of Ethernet cable detection
by the "fec" Ethernet driver.
In normal operation, if I unplug the Ethernet cable, then "fec" driver
prints "fec 83fec000.ethernet eth0: Link is Down" and green LED
(Ethernet medium detected) is OFF.
If I plug cable back, then "fec" driver print "fec 83fec000.ethernet
eth0: Link is Up - 100Mbps/Full - flow control off" and green LED is ON.
But sometimes, after cable plugging, "fec" driver does not print
anything on the console and green LED does not show detection of
Ethernet cable. Frequency of issue appearing is a random value.
Sometimes issue appears after second cable unplugging/plugging, but
sometimes - after 10-20 unplugging/plugging.
The issue was tested and exists on kernels from linux-3.8.5 till current
linux-4.2-rc4-cbfe8fa6cd672011c755c3cd85c9ffd4e2d10a6f.
Same tests was made with different versions of the Barebox bootloader
and cable detection works flawless.
Please, help to resolve issue with Linux drivers.
Best wishes.
--
Igor Plyatov
From: Igor Plyatov <[email protected]> Sent: Monday, July 27, 2015 10:51 PM
> To: [email protected]; [email protected]
> Cc: Florian Fainelli; Joe Perches; Zhou Luwei-B45643; Duan Fugang-B38611;
> Richard Cochran; David S. Miller; Uwe Kleine-König; Estevam Fabio-R49496;
> Lothar Waßmann; Li Frank-B20596
> Subject: Buggy cable detection on i.MX51, fec driver and LAN8700 PHY
>
> Dear all,
>
> very often we observe issue with Ethernet cable detection during cable
> unplugging and plugging.
>
> We use Voipac i.MX51 SOMs (System On Modules). They are based on
> Freescale i.MX51 CPU with LAN7800 PHY in MII mode. The schematic of PHY
> connection is very similar to the Freescale i.MX51 Babbage board.
>
> The Ethernet interface eth0 is configured statically for simplicity, but
> same issue exists with DHCP configuration.
>
> I did a lot of tests to determine stability of Ethernet cable detection
> by the "fec" Ethernet driver.
>
> In normal operation, if I unplug the Ethernet cable, then "fec" driver
> prints "fec 83fec000.ethernet eth0: Link is Down" and green LED (Ethernet
> medium detected) is OFF.
> If I plug cable back, then "fec" driver print "fec 83fec000.ethernet
> eth0: Link is Up - 100Mbps/Full - flow control off" and green LED is ON.
>
> But sometimes, after cable plugging, "fec" driver does not print anything
> on the console and green LED does not show detection of Ethernet cable.
> Frequency of issue appearing is a random value.
> Sometimes issue appears after second cable unplugging/plugging, but
> sometimes - after 10-20 unplugging/plugging.
>
> The issue was tested and exists on kernels from linux-3.8.5 till current
> linux-4.2-rc4-cbfe8fa6cd672011c755c3cd85c9ffd4e2d10a6f.
>
> Same tests was made with different versions of the Barebox bootloader and
> cable detection works flawless.
>
> Please, help to resolve issue with Linux drivers.
>
> Best wishes.
> --
> Igor Plyatov
For phy cable detection issue, mostly it is phy device issue like:
- Phy is not stable, maybe the phy initial setting is not right.
- MDIO bus read is not right, maybe MDIO/MDC pin drive strength (timing) doesn't match spec requirement.
You can measure the MDIO timing firstly, and then check the phy setting.
Regards,
Andy
????{.n?+???????+%?????ݶ??w??{.n?+????{??G?????{ay? ʇڙ?,j??f???h?????????z_??(?階?ݢj"???m??????G????????????&???~???iO???z??v?^?m???? ????????I?
On Mon, Jul 27, 2015 at 11:50 AM, Igor Plyatov <[email protected]> wrote:
> Dear all,
>
> very often we observe issue with Ethernet cable detection during cable
> unplugging and plugging.
>
> We use Voipac i.MX51 SOMs (System On Modules). They are based on Freescale
> i.MX51 CPU with LAN7800 PHY in MII mode. The schematic of PHY connection is
> very similar to the Freescale i.MX51 Babbage board.
>
> The Ethernet interface eth0 is configured statically for simplicity, but
> same issue exists with DHCP configuration.
>
> I did a lot of tests to determine stability of Ethernet cable detection by
> the "fec" Ethernet driver.
>
> In normal operation, if I unplug the Ethernet cable, then "fec" driver
> prints "fec 83fec000.ethernet eth0: Link is Down" and green LED (Ethernet
> medium detected) is OFF.
> If I plug cable back, then "fec" driver print "fec 83fec000.ethernet eth0:
> Link is Up - 100Mbps/Full - flow control off" and green LED is ON.
>
> But sometimes, after cable plugging, "fec" driver does not print anything on
> the console and green LED does not show detection of Ethernet cable.
> Frequency of issue appearing is a random value. Sometimes issue appears
> after second cable unplugging/plugging, but sometimes - after 10-20
> unplugging/plugging.
>
> The issue was tested and exists on kernels from linux-3.8.5 till current
> linux-4.2-rc4-cbfe8fa6cd672011c755c3cd85c9ffd4e2d10a6f.
>
> Same tests was made with different versions of the Barebox bootloader and
> cable detection works flawless.
>
> Please, help to resolve issue with Linux drivers.
I tried linux-next on a imx51-babbage and could not reproduce the problem here.
Regards,
Fabio Estevam