2015-11-19 23:05:57

by Jon Mason

[permalink] [raw]
Subject: [PATCH v2 0/3] ARM: dts: add support for NS, NSP, and NS2 clocks

Changes in v2:
Rebased off of outstanding NSP DT patches and tweaked the entry names
per Ray Jui


This patch series adds device tree support for the Broadcom Northstar,
Northstar Plus, and Northstar 2 clocks.

Last sent as an RFC (see https://lkml.org/lkml/2015/10/13/882) due to
the inability to merge because of the driver dependencies. Those
necessary driver changes were merged into 4.4. All comments have been
addressed and it is ready to be pulled in.


Jon Mason (3):
ARM: dts: enable clock support for BCM5301X
ARM: dts: enable clock support for Broadcom NSP
ARM64: dts: enable clock support for Broadcom NS2

arch/arm/boot/dts/bcm-nsp.dtsi | 77 ++++++++++++++++++++++++-----
arch/arm/boot/dts/bcm5301x.dtsi | 92 +++++++++++++++++++++++++++--------
arch/arm64/boot/dts/broadcom/ns2.dtsi | 80 +++++++++++++++++++++++++++++-
3 files changed, 214 insertions(+), 35 deletions(-)

--
1.9.1


2015-11-19 23:05:59

by Jon Mason

[permalink] [raw]
Subject: [PATCH v2 1/3] ARM: dts: enable clock support for BCM5301X

Replace current device tree dummy clocks with real clock support for
Broadcom Northstar SoCs.

Signed-off-by: Jon Mason <[email protected]>
---
arch/arm/boot/dts/bcm5301x.dtsi | 92 +++++++++++++++++++++++++++++++----------
1 file changed, 71 insertions(+), 21 deletions(-)

diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
index 6f50f67..65a1309 100644
--- a/arch/arm/boot/dts/bcm5301x.dtsi
+++ b/arch/arm/boot/dts/bcm5301x.dtsi
@@ -8,6 +8,7 @@
* Licensed under the GNU/GPL. See COPYING for details.
*/

+#include <dt-bindings/clock/bcm-nsp.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
@@ -27,7 +28,7 @@
compatible = "ns16550";
reg = <0x0300 0x100>;
interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
- clock-frequency = <100000000>;
+ clocks = <&iprocslow>;
status = "disabled";
};

@@ -35,48 +36,55 @@
compatible = "ns16550";
reg = <0x0400 0x100>;
interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
- clock-frequency = <100000000>;
+ clocks = <&iprocslow>;
status = "disabled";
};
};

mpcore {
compatible = "simple-bus";
- ranges = <0x00000000 0x19020000 0x00003000>;
+ ranges = <0x00000000 0x19000000 0x00023000>;
#address-cells = <1>;
#size-cells = <1>;

- scu@0000 {
+ a9pll: arm_clk@00000 {
+ #clock-cells = <0>;
+ compatible = "brcm,nsp-armpll";
+ clocks = <&osc>;
+ reg = <0x00000 0x1000>;
+ };
+
+ scu@20000 {
compatible = "arm,cortex-a9-scu";
- reg = <0x0000 0x100>;
+ reg = <0x20000 0x100>;
};

- timer@0200 {
+ timer@20200 {
compatible = "arm,cortex-a9-global-timer";
- reg = <0x0200 0x100>;
+ reg = <0x20200 0x100>;
interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clk_periph>;
+ clocks = <&periph_clk>;
};

- local-timer@0600 {
+ local-timer@20600 {
compatible = "arm,cortex-a9-twd-timer";
- reg = <0x0600 0x100>;
+ reg = <0x20600 0x100>;
interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clk_periph>;
+ clocks = <&periph_clk>;
};

- gic: interrupt-controller@1000 {
+ gic: interrupt-controller@21000 {
compatible = "arm,cortex-a9-gic";
#interrupt-cells = <3>;
#address-cells = <0>;
interrupt-controller;
- reg = <0x1000 0x1000>,
- <0x0100 0x100>;
+ reg = <0x21000 0x1000>,
+ <0x20100 0x100>;
};

- L2: cache-controller@2000 {
+ L2: cache-controller@22000 {
compatible = "arm,pl310-cache";
- reg = <0x2000 0x1000>;
+ reg = <0x22000 0x1000>;
cache-unified;
arm,shared-override;
prefetch-data = <1>;
@@ -94,14 +102,37 @@

clocks {
#address-cells = <1>;
- #size-cells = <0>;
+ #size-cells = <1>;
+ ranges;

- /* As long as we do not have a real clock driver us this
- * fixed clock */
- clk_periph: periph {
+ osc: oscillator {
+ #clock-cells = <0>;
compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ };
+
+ iprocmed: iprocmed {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
+ clock-div = <2>;
+ clock-mult = <1>;
+ };
+
+ iprocslow: iprocslow {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
+ clock-div = <4>;
+ clock-mult = <1>;
+ };
+
+ periph_clk: periph_clk {
#clock-cells = <0>;
- clock-frequency = <400000000>;
+ compatible = "fixed-factor-clock";
+ clocks = <&a9pll>;
+ clock-div = <2>;
+ clock-mult = <1>;
};
};

@@ -178,6 +209,25 @@
};
};

+ lcpll0: lcpll0@1800c100 {
+ #clock-cells = <1>;
+ compatible = "brcm,nsp-lcpll0";
+ reg = <0x1800c100 0x14>;
+ clocks = <&osc>;
+ clock-output-names = "lcpll0", "pcie_phy", "sdio",
+ "ddr_phy";
+ };
+
+ genpll: genpll@1800c140 {
+ #clock-cells = <1>;
+ compatible = "brcm,nsp-genpll";
+ reg = <0x1800c140 0x24>;
+ clocks = <&osc>;
+ clock-output-names = "genpll", "phy", "ethernetclk",
+ "usbclk", "iprocfast", "sata1",
+ "sata2";
+ };
+
nand: nand@18028000 {
compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1", "brcm,brcmnand";
reg = <0x18028000 0x600>, <0x1811a408 0x600>, <0x18028f00 0x20>;
--
1.9.1

2015-11-19 23:06:53

by Jon Mason

[permalink] [raw]
Subject: [PATCH v2 2/3] ARM: dts: enable clock support for Broadcom NSP

Replace current device tree dummy clocks with real clock support for
Broadcom Northstar Plus SoC

Signed-off-by: Jon Mason <[email protected]>
---
arch/arm/boot/dts/bcm-nsp.dtsi | 77 +++++++++++++++++++++++++++++++++++-------
1 file changed, 64 insertions(+), 13 deletions(-)

diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi
index b74438c..361c2a6 100644
--- a/arch/arm/boot/dts/bcm-nsp.dtsi
+++ b/arch/arm/boot/dts/bcm-nsp.dtsi
@@ -32,6 +32,7 @@

#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/clock/bcm-nsp.h>

#include "skeleton.dtsi"

@@ -42,7 +43,7 @@

mpcore {
compatible = "simple-bus";
- ranges = <0x00000000 0x19020000 0x00003000>;
+ ranges = <0x00000000 0x19000000 0x00023000>;
#address-cells = <1>;
#size-cells = <1>;

@@ -58,16 +59,23 @@
};
};

+ a9pll: arm_clk@0000 {
+ #clock-cells = <0>;
+ compatible = "brcm,nsp-armpll";
+ clocks = <&osc>;
+ reg = <0x0000 0x1000>;
+ };
+
timer@0200 {
compatible = "arm,cortex-a9-global-timer";
- reg = <0x0200 0x100>;
+ reg = <0x20200 0x100>;
interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&periph_clk>;
};

twd-timer@0600 {
compatible = "arm,cortex-a9-twd-timer";
- reg = <0x0600 0x20>;
+ reg = <0x20600 0x20>;
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
IRQ_TYPE_LEVEL_HIGH)>;
clocks = <&periph_clk>;
@@ -75,7 +83,7 @@

twd-watchdog@0620 {
compatible = "arm,cortex-a9-twd-wdt";
- reg = <0x0620 0x20>;
+ reg = <0x20620 0x20>;
interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
IRQ_TYPE_LEVEL_HIGH)>;
clocks = <&periph_clk>;
@@ -86,13 +94,13 @@
#interrupt-cells = <3>;
#address-cells = <0>;
interrupt-controller;
- reg = <0x1000 0x1000>,
- <0x0100 0x100>;
+ reg = <0x21000 0x1000>,
+ <0x20100 0x100>;
};

L2: l2-cache {
compatible = "arm,pl310-cache";
- reg = <0x2000 0x1000>;
+ reg = <0x22000 0x1000>;
cache-unified;
cache-level = <2>;
};
@@ -103,10 +111,34 @@
#size-cells = <1>;
ranges;

- periph_clk: periph_clk {
+ osc: oscillator {
+ #clock-cells = <0>;
compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ };
+
+ iprocmed: iprocmed {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
+ clock-div = <2>;
+ clock-mult = <1>;
+ };
+
+ iprocslow: iprocslow {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
+ clock-div = <4>;
+ clock-mult = <1>;
+ };
+
+ periph_clk: periph_clk {
#clock-cells = <0>;
- clock-frequency = <500000000>;
+ compatible = "fixed-factor-clock";
+ clocks = <&a9pll>;
+ clock-div = <2>;
+ clock-mult = <1>;
};
};

@@ -118,17 +150,17 @@

uart0: serial@0300 {
compatible = "ns16550a";
- reg = <0x0300 0x100>;
+ reg = <0x000300 0x100>;
interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
- clock-frequency = <62499840>;
+ clocks = <&osc>;
status = "disabled";
};

uart1: serial@0400 {
compatible = "ns16550a";
- reg = <0x0400 0x100>;
+ reg = <0x000400 0x100>;
interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
- clock-frequency = <62499840>;
+ clocks = <&osc>;
status = "disabled";
};

@@ -226,5 +258,24 @@
interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>;
clock-frequency = <100000>;
};
+
+ lcpll0: lcpll0@3f100 {
+ #clock-cells = <1>;
+ compatible = "brcm,nsp-lcpll0";
+ reg = <0x3f100 0x14>;
+ clocks = <&osc>;
+ clock-output-names = "lcpll0", "pcie_phy", "sdio",
+ "ddr_phy";
+ };
+
+ genpll: genpll@3f140 {
+ #clock-cells = <1>;
+ compatible = "brcm,nsp-genpll";
+ reg = <0x3f140 0x24>;
+ clocks = <&osc>;
+ clock-output-names = "genpll", "phy", "ethernetclk",
+ "usbclk", "iprocfast", "sata1",
+ "sata2";
+ };
};
};
--
1.9.1

2015-11-19 23:06:21

by Jon Mason

[permalink] [raw]
Subject: [PATCH v2 3/3] ARM64: dts: enable clock support for Broadcom NS2

Add device tree entries for clock support for Broadcom Northstar 2 SoC

Signed-off-by: Jon Mason <[email protected]>
---
arch/arm64/boot/dts/broadcom/ns2.dtsi | 80 ++++++++++++++++++++++++++++++++++-
1 file changed, 79 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/broadcom/ns2.dtsi b/arch/arm64/boot/dts/broadcom/ns2.dtsi
index 9610822..a510d3a 100644
--- a/arch/arm64/boot/dts/broadcom/ns2.dtsi
+++ b/arch/arm64/boot/dts/broadcom/ns2.dtsi
@@ -31,6 +31,7 @@
*/

#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/bcm-ns2.h>

/memreserve/ 0x84b00000 0x00000008;

@@ -109,6 +110,33 @@
<&A57_3>;
};

+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ osc: oscillator {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ };
+
+ iprocmed: iprocmed {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&genpll_scr BCM_NS2_GENPLL_SCR_SCR_CLK>;
+ clock-div = <2>;
+ clock-mult = <1>;
+ };
+
+ iprocslow: iprocslow {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&genpll_scr BCM_NS2_GENPLL_SCR_SCR_CLK>;
+ clock-div = <4>;
+ clock-mult = <1>;
+ };
+ };
+
soc: soc {
compatible = "simple-bus";
#address-cells = <1>;
@@ -156,6 +184,56 @@
mmu-masters;
};

+ lcpll_ddr: lcpll_ddr@6501d058 {
+ #clock-cells = <1>;
+ compatible = "brcm,ns2-lcpll-ddr";
+ reg = <0x6501d058 0x20>,
+ <0x6501c020 0x4>,
+ <0x6501d04c 0x4>;
+ clocks = <&osc>;
+ clock-output-names = "lcpll_ddr", "pcie_sata_usb",
+ "ddr", "ddr_ch2_unused",
+ "ddr_ch3_unused", "ddr_ch4_unused",
+ "ddr_ch5_unused";
+ };
+
+ lcpll_ports: lcpll_ports@6501d078 {
+ #clock-cells = <1>;
+ compatible = "brcm,ns2-lcpll-ports";
+ reg = <0x6501d078 0x20>,
+ <0x6501c020 0x4>,
+ <0x6501d054 0x4>;
+ clocks = <&osc>;
+ clock-output-names = "lcpll_ports", "wan", "rgmii",
+ "ports_ch2_unused",
+ "ports_ch3_unused",
+ "ports_ch4_unused",
+ "ports_ch5_unused";
+ };
+
+ genpll_scr: genpll_scr@6501d098 {
+ #clock-cells = <1>;
+ compatible = "brcm,ns2-genpll-scr";
+ reg = <0x6501d098 0x32>,
+ <0x6501c020 0x4>,
+ <0x6501d044 0x4>;
+ clocks = <&osc>;
+ clock-output-names = "genpll_scr", "scr", "fs",
+ "audio_ref", "scr_ch3_unused",
+ "scr_ch4_unused", "scr_ch5_unused";
+ };
+
+ genpll_sw: genpll_sw@6501d0c4 {
+ #clock-cells = <1>;
+ compatible = "brcm,ns2-genpll-sw";
+ reg = <0x6501d0c4 0x32>,
+ <0x6501c020 0x4>,
+ <0x6501d044 0x4>;
+ clocks = <&osc>;
+ clock-output-names = "genpll_sw", "rpe", "250", "nic",
+ "chimp", "port", "sdio";
+ };
+
crmu: crmu@65024000 {
compatible = "syscon";
reg = <0x65024000 0x100>;
@@ -204,7 +282,7 @@
interrupts = <GIC_SPI 393 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clock-frequency = <23961600>;
+ clocks = <&osc>;
status = "disabled";
};

--
1.9.1

2015-11-19 23:40:12

by Ray Jui

[permalink] [raw]
Subject: Re: [PATCH v2 2/3] ARM: dts: enable clock support for Broadcom NSP



On 11/19/2015 3:05 PM, Jon Mason wrote:
> Replace current device tree dummy clocks with real clock support for
> Broadcom Northstar Plus SoC
>
> Signed-off-by: Jon Mason <[email protected]>
> ---
> arch/arm/boot/dts/bcm-nsp.dtsi | 77 +++++++++++++++++++++++++++++++++++-------
> 1 file changed, 64 insertions(+), 13 deletions(-)
>
> diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi
> index b74438c..361c2a6 100644
> --- a/arch/arm/boot/dts/bcm-nsp.dtsi
> +++ b/arch/arm/boot/dts/bcm-nsp.dtsi
> @@ -32,6 +32,7 @@
>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/clock/bcm-nsp.h>
>
> #include "skeleton.dtsi"
>
> @@ -42,7 +43,7 @@
>
> mpcore {
> compatible = "simple-bus";
> - ranges = <0x00000000 0x19020000 0x00003000>;
> + ranges = <0x00000000 0x19000000 0x00023000>;
> #address-cells = <1>;
> #size-cells = <1>;
>
> @@ -58,16 +59,23 @@
> };
> };
>
> + a9pll: arm_clk@0000 {
> + #clock-cells = <0>;
> + compatible = "brcm,nsp-armpll";
> + clocks = <&osc>;
> + reg = <0x0000 0x1000>;
> + };
> +
> timer@0200 {

timer@20200. Or is this addressed in another patch? I completely lose
track of these....

> compatible = "arm,cortex-a9-global-timer";
> - reg = <0x0200 0x100>;
> + reg = <0x20200 0x100>;
> interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&periph_clk>;
> };
>
> twd-timer@0600 {

twd-timer@20600

> compatible = "arm,cortex-a9-twd-timer";
> - reg = <0x0600 0x20>;
> + reg = <0x20600 0x20>;
> interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
> IRQ_TYPE_LEVEL_HIGH)>;
> clocks = <&periph_clk>;
> @@ -75,7 +83,7 @@
>
> twd-watchdog@0620 {

same here

> compatible = "arm,cortex-a9-twd-wdt";
> - reg = <0x0620 0x20>;
> + reg = <0x20620 0x20>;
> interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
> IRQ_TYPE_LEVEL_HIGH)>;
> clocks = <&periph_clk>;
> @@ -86,13 +94,13 @@
> #interrupt-cells = <3>;
> #address-cells = <0>;
> interrupt-controller;
> - reg = <0x1000 0x1000>,
> - <0x0100 0x100>;
> + reg = <0x21000 0x1000>,
> + <0x20100 0x100>;
> };
>
> L2: l2-cache {
> compatible = "arm,pl310-cache";
> - reg = <0x2000 0x1000>;
> + reg = <0x22000 0x1000>;
> cache-unified;
> cache-level = <2>;
> };
> @@ -103,10 +111,34 @@
> #size-cells = <1>;
> ranges;
>
> - periph_clk: periph_clk {
> + osc: oscillator {
> + #clock-cells = <0>;
> compatible = "fixed-clock";
> + clock-frequency = <25000000>;
> + };
> +
> + iprocmed: iprocmed {
> + #clock-cells = <0>;
> + compatible = "fixed-factor-clock";
> + clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
> + clock-div = <2>;
> + clock-mult = <1>;
> + };
> +
> + iprocslow: iprocslow {
> + #clock-cells = <0>;
> + compatible = "fixed-factor-clock";
> + clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
> + clock-div = <4>;
> + clock-mult = <1>;
> + };
> +
> + periph_clk: periph_clk {
> #clock-cells = <0>;
> - clock-frequency = <500000000>;
> + compatible = "fixed-factor-clock";
> + clocks = <&a9pll>;
> + clock-div = <2>;
> + clock-mult = <1>;
> };
> };
>
> @@ -118,17 +150,17 @@
>
> uart0: serial@0300 {
> compatible = "ns16550a";
> - reg = <0x0300 0x100>;
> + reg = <0x000300 0x100>;
> interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
> - clock-frequency = <62499840>;
> + clocks = <&osc>;
> status = "disabled";
> };
>
> uart1: serial@0400 {
> compatible = "ns16550a";
> - reg = <0x0400 0x100>;
> + reg = <0x000400 0x100>;
> interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
> - clock-frequency = <62499840>;
> + clocks = <&osc>;
> status = "disabled";
> };
>
> @@ -226,5 +258,24 @@
> interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>;
> clock-frequency = <100000>;
> };
> +
> + lcpll0: lcpll0@3f100 {
> + #clock-cells = <1>;
> + compatible = "brcm,nsp-lcpll0";
> + reg = <0x3f100 0x14>;
> + clocks = <&osc>;
> + clock-output-names = "lcpll0", "pcie_phy", "sdio",
> + "ddr_phy";
> + };
> +
> + genpll: genpll@3f140 {
> + #clock-cells = <1>;
> + compatible = "brcm,nsp-genpll";
> + reg = <0x3f140 0x24>;
> + clocks = <&osc>;
> + clock-output-names = "genpll", "phy", "ethernetclk",
> + "usbclk", "iprocfast", "sata1",
> + "sata2";
> + };
> };
> };
>

2015-11-20 15:14:46

by Jon Mason

[permalink] [raw]
Subject: Re: [PATCH v2 2/3] ARM: dts: enable clock support for Broadcom NSP

On Thu, Nov 19, 2015 at 03:40:04PM -0800, Ray Jui wrote:
>
>
> On 11/19/2015 3:05 PM, Jon Mason wrote:
> >Replace current device tree dummy clocks with real clock support for
> >Broadcom Northstar Plus SoC
> >
> >Signed-off-by: Jon Mason <[email protected]>
> >---
> > arch/arm/boot/dts/bcm-nsp.dtsi | 77 +++++++++++++++++++++++++++++++++++-------
> > 1 file changed, 64 insertions(+), 13 deletions(-)
> >
> >diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi
> >index b74438c..361c2a6 100644
> >--- a/arch/arm/boot/dts/bcm-nsp.dtsi
> >+++ b/arch/arm/boot/dts/bcm-nsp.dtsi
> >@@ -32,6 +32,7 @@
> >
> > #include <dt-bindings/interrupt-controller/arm-gic.h>
> > #include <dt-bindings/interrupt-controller/irq.h>
> >+#include <dt-bindings/clock/bcm-nsp.h>
> >
> > #include "skeleton.dtsi"
> >
> >@@ -42,7 +43,7 @@
> >
> > mpcore {
> > compatible = "simple-bus";
> >- ranges = <0x00000000 0x19020000 0x00003000>;
> >+ ranges = <0x00000000 0x19000000 0x00023000>;
> > #address-cells = <1>;
> > #size-cells = <1>;
> >
> >@@ -58,16 +59,23 @@
> > };
> > };
> >
> >+ a9pll: arm_clk@0000 {
> >+ #clock-cells = <0>;
> >+ compatible = "brcm,nsp-armpll";
> >+ clocks = <&osc>;
> >+ reg = <0x0000 0x1000>;
> >+ };
> >+
> > timer@0200 {
>
> timer@20200. Or is this addressed in another patch? I completely
> lose track of these....

No, you are correct. The names need to be updated as well with the
new offsets. New series to follow.

Thanks,
Jon

>
> > compatible = "arm,cortex-a9-global-timer";
> >- reg = <0x0200 0x100>;
> >+ reg = <0x20200 0x100>;
> > interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
> > clocks = <&periph_clk>;
> > };
> >
> > twd-timer@0600 {
>
> twd-timer@20600
>
> > compatible = "arm,cortex-a9-twd-timer";
> >- reg = <0x0600 0x20>;
> >+ reg = <0x20600 0x20>;
> > interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
> > IRQ_TYPE_LEVEL_HIGH)>;
> > clocks = <&periph_clk>;
> >@@ -75,7 +83,7 @@
> >
> > twd-watchdog@0620 {
>
> same here
>
> > compatible = "arm,cortex-a9-twd-wdt";
> >- reg = <0x0620 0x20>;
> >+ reg = <0x20620 0x20>;
> > interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
> > IRQ_TYPE_LEVEL_HIGH)>;
> > clocks = <&periph_clk>;
> >@@ -86,13 +94,13 @@
> > #interrupt-cells = <3>;
> > #address-cells = <0>;
> > interrupt-controller;
> >- reg = <0x1000 0x1000>,
> >- <0x0100 0x100>;
> >+ reg = <0x21000 0x1000>,
> >+ <0x20100 0x100>;
> > };
> >
> > L2: l2-cache {
> > compatible = "arm,pl310-cache";
> >- reg = <0x2000 0x1000>;
> >+ reg = <0x22000 0x1000>;
> > cache-unified;
> > cache-level = <2>;
> > };
> >@@ -103,10 +111,34 @@
> > #size-cells = <1>;
> > ranges;
> >
> >- periph_clk: periph_clk {
> >+ osc: oscillator {
> >+ #clock-cells = <0>;
> > compatible = "fixed-clock";
> >+ clock-frequency = <25000000>;
> >+ };
> >+
> >+ iprocmed: iprocmed {
> >+ #clock-cells = <0>;
> >+ compatible = "fixed-factor-clock";
> >+ clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
> >+ clock-div = <2>;
> >+ clock-mult = <1>;
> >+ };
> >+
> >+ iprocslow: iprocslow {
> >+ #clock-cells = <0>;
> >+ compatible = "fixed-factor-clock";
> >+ clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
> >+ clock-div = <4>;
> >+ clock-mult = <1>;
> >+ };
> >+
> >+ periph_clk: periph_clk {
> > #clock-cells = <0>;
> >- clock-frequency = <500000000>;
> >+ compatible = "fixed-factor-clock";
> >+ clocks = <&a9pll>;
> >+ clock-div = <2>;
> >+ clock-mult = <1>;
> > };
> > };
> >
> >@@ -118,17 +150,17 @@
> >
> > uart0: serial@0300 {
> > compatible = "ns16550a";
> >- reg = <0x0300 0x100>;
> >+ reg = <0x000300 0x100>;
> > interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
> >- clock-frequency = <62499840>;
> >+ clocks = <&osc>;
> > status = "disabled";
> > };
> >
> > uart1: serial@0400 {
> > compatible = "ns16550a";
> >- reg = <0x0400 0x100>;
> >+ reg = <0x000400 0x100>;
> > interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
> >- clock-frequency = <62499840>;
> >+ clocks = <&osc>;
> > status = "disabled";
> > };
> >
> >@@ -226,5 +258,24 @@
> > interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>;
> > clock-frequency = <100000>;
> > };
> >+
> >+ lcpll0: lcpll0@3f100 {
> >+ #clock-cells = <1>;
> >+ compatible = "brcm,nsp-lcpll0";
> >+ reg = <0x3f100 0x14>;
> >+ clocks = <&osc>;
> >+ clock-output-names = "lcpll0", "pcie_phy", "sdio",
> >+ "ddr_phy";
> >+ };
> >+
> >+ genpll: genpll@3f140 {
> >+ #clock-cells = <1>;
> >+ compatible = "brcm,nsp-genpll";
> >+ reg = <0x3f140 0x24>;
> >+ clocks = <&osc>;
> >+ clock-output-names = "genpll", "phy", "ethernetclk",
> >+ "usbclk", "iprocfast", "sata1",
> >+ "sata2";
> >+ };
> > };
> > };
> >